In preparation for removing the manual EMIT_FLUSH prior to emitting the
breadcrumb implement the flush inline with writing the breadcrumb for
ringbuffer emission.
With a combined flush+breadcrumb, we can use a single operation to both
flush and after the flush is complete (post-sync) write the breadcrumb.
This gives us a strongly ordered operation that should be sufficient to
serialise the write before we emit the interrupt; and therefore we may
take the opportunity to remove the irq_seqno_barrier w/a for gen6+.
Although using the PIPECONTROL to write the breadcrumb is slower than
MI_STORE_DWORD_IMM, by combining the operations into one and removing the
extra flush (next patch) it is faster
For gen2-5, we simply combine the MI_FLUSH into the breadcrumb emission,
though maybe we could find a solution here to the seqno-vs-interrupt
issue on Ironlake by mixing up the flush? The answer is no, adding an
MI_FLUSH before the interrupt is insufficient.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228153114.4948-2-chris@chris-wilson.co.uk
In preparation for removing the manual EMIT_FLUSH prior to emitting the
breadcrumb implement the flush inline with writing the breadcrumb for
execlists. Using one command to both flush and write the breadcrumb is
naturally a tiny bit faster than splitting it into two.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228153114.4948-1-chris@chris-wilson.co.uk
Having just gutted the implementation as there is no global seqno
tracking, remove the vestigal write-only stub for debugfs/i915_next_seqno.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228140736.32606-3-chris@chris-wilson.co.uk
The writing is on the wall for the existence of a single execution queue
along each engine, and as a consequence we will not be able to track
dependencies along the HW queue itself, i.e. we will not be able to use
HW semaphores on gen7 as they use a global set of registers (and unlike
gen8+ we can not effectively target memory to keep per-context seqno and
dependencies).
On the positive side, when we implement request reordering for gen7 we
also can not presume a simple execution queue and would also require
removing the current semaphore generation code. So this bring us another
step closer to request reordering for ringbuffer submission!
The negative side is that using interrupts to drive inter-engine
synchronisation is much slower (4us -> 15us to do a nop on each of the 3
engines on ivb). This is much better than it was at the time of introducing
the HW semaphores and equally important userspace weaned itself off
intermixing dependent BLT/RENDER operations (the prime culprit was glyph
rendering in UXA). So while we regress the microbenchmarks, it should not
impact the user.
References: https://bugs.freedesktop.org/show_bug.cgi?id=108888
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228140736.32606-2-chris@chris-wilson.co.uk
After we found a workaround for a hang on context load, Ben Widawsky
found confirmation that it was for an issue with waking from rc6 and
loading a context image.
The workaround from on high suggests that we should
I915_WRITE(RING_WAIT_FOR_RC6_EXIT(engine->mmio_base),
_MASKED_FIELD(RING_RC6_SEL_WRITE_ADDR_MASK,
RING_RC6_SEL_WRITE_ADDR_UPPER_LEFT));
in our rc6 setup for Haswell GT1, but on applying that we find instead
that the machine encounters a GT forcewake error and locks up.
As we are removing HW semaphore usage in the next patch, and the
suggested workaround is no improvement, we need to
decouple the PSMI workaround from HAS_SEMAPHORES to IS_HSW_GT1.
References: 2c55018347 ("drm/i915: Disable PSMI sleep messages on all rings around context switches")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181228140736.32606-1-chris@chris-wilson.co.uk
The information presented here is not relevant to current development.
We can either use the context information, but more often we want to
inspect the active gpu state.
The ulterior motive is to eradicate dev->filelist.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181227121549.29139-1-chris@chris-wilson.co.uk
Call intel_psr_enable() and intel_edp_drrs_enable() on pipe updates to make
sure that we enable PSR / DRRS (when applicable) on fastsets.
Note calling these functions when PSR / DRRS has already been enabled is a
no-op, so it is safe to do this on every encoder->update_pipe callback.
Changes in v2:
-Merge the patches adding the intel_psr_enable() and intel_edp_drrs_enable()
calls into a single patch
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220132120.15318-3-hdegoede@redhat.com
Do not make it an error to call intel_edp_drrs_enable while drrs has
already been enabled, instead exit silently in this case.
This is a preparation patch for ensuring that DRRS is enabled on fastsets.
Note that the removed WARN_ON could also be triggered from userspace
through the i915_drrs_ctl debugfs entry which was added by
commit 35954e88bc ("drm/i915: Runtime disable for eDP DRRS")
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220132120.15318-2-hdegoede@redhat.com
When we are doing a fastset (needs_modeset=false, update_pipe=true) we
may need to update some encoder-level things such as checking that PSR
is enabled.
This commit adds an update_pipe callback to intel_encoder and a new
intel_encoders_update_pipe helper which calls this for all encoders
connected to a crtc. The new intel_encoders_update_pipe helper is called
from intel_update_crtc when doing a fastset.
Changes in v2:
-Name the new encoder callback update_pipe instead of just update
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220132120.15318-1-hdegoede@redhat.com
If we fail to pin the ggtt vma slot for the ppgtt page tables, we need
to unwind the locals before reporting the error. Or else on subsequent
attempts to bind the page tables into the ggtt, we will already believe
that the vma has been pinned and continue on blithely. If something else
should happen to be at that location, choas ensues.
Fixes: a2bbf71483 ("drm/i915/gtt: Only keep gen6 page directories pinned while active")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.william.auld@gmail.com>
Cc: <stable@vger.kernel.org> # v4.19+
Reviewed-by: Matthew Auld <matthew.william.auld@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181222030623.21710-1-chris@chris-wilson.co.uk
BSpec does not show these WAs as applicable to GLK, and for CNL it
only shows them applicable for a super early pre-production stepping
we shouldn't be caring about anymore. Remove these so we can avoid
them on ICL too.
v2: Change how we check for gen9 display platforms (Ville).
Cc: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181114012432.21809-1-paulo.r.zanoni@intel.com
Without this, we will get a dmesg-warn when enable_fbc is cleared on a fastset:
WARN_ON(!crtc_state->enable_fbc)
WARNING: CPU: 0 PID: 1090 at drivers/gpu/drm/i915/intel_fbc.c:1091 intel_fbc_enable+0x2ce/0x580 [i915]
RIP: 0010:intel_fbc_enable+0x2ce/0x580 [i915]
Call Trace:
? __mutex_unlock_slowpath+0x46/0x2b0
intel_update_crtc+0x6f/0x2b0 [i915]
skl_update_crtcs+0x1d1/0x2b0 [i915]
intel_atomic_commit_tail+0x1ea/0xdb0 [i915]
intel_atomic_commit+0x244/0x330 [i915]
drm_mode_atomic_ioctl+0x85d/0x950
? drm_atomic_set_property+0x970/0x970
drm_ioctl_kernel+0x81/0xf0
drm_ioctl+0x2de/0x390
? drm_atomic_set_property+0x970/0x970
? __handle_mm_fault+0x81b/0xfc0
do_vfs_ioctl+0xa0/0x6e0
? __do_page_fault+0x2a5/0x550
ksys_ioctl+0x35/0x60
__x64_sys_ioctl+0x11/0x20
do_syscall_64+0x55/0x190
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Changes since v1:
- Move intel_fbc_disable to intel_update_crtc() (Hans)
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181220151719.30586-1-maarten.lankhorst@linux.intel.com
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Add a fallback detection method for TypeC legacy ports in case the
VBT port information used to detect normally such ports is
incorrect.
For the fallback method we use the TypeC legacy mode specific HPD
interrupt flag which should only be raised for a legacy port.
WARN if the VBT port info is incorrect.
In a case where we'd detect the port in a contradicting way both as a
legacy and also as a USB DP and/or TBT alternate port treat the port
as legacy (by also emitting a WARN from icl_update_tc_port_type).
v2:
- Repurpose the detection as a fallback method instead of using
it only for the DP legacy case. By now we should normally use VBT to
detect DP legacy ports as well.
Suggested-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com> (v1)
Reviewed-by: Mika Kahola <mika.kahola@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-5-imre.deak@intel.com
Atm HPD disconnect events on TypeC ports will break things, since we'll
switch the TypeC mode (between legacy and disconnected modes as well as
among USB DP alternate, Thunderbolt alternate and disconnected modes) on
the fly from the HPD disconnect interrupt work while the port may be
still active.
Even if the port happens to be not active during the disconnect we'd
still have a problem during a subsequent modeset or AUX transfer that
could happen regardless of the port's connected state. For instance the
system resume display mode restore code and userspace could perform a
modeset on the port or userspace could start an AUX transfer even if the
port is in disconnected state.
To fix this keep TypeC legacy ports in legacy mode whenever we're not
suspended. This mode is a static configuration as opposed to the
Thunderbolt and USB DP alternate modes between which we can switch
dynamically.
We determine if a TypeC port is legacy (wired to a legacy HDMI or a
legacy DP connector) via the VBT DDI port specific USB-TypeC and
Thunderbolt flags. If both these flags are cleared then the port is
configured for legacy mode.
On such legacy ports we'll run the TypeC PHY connect sequence explicitly
during driver loading and system resume (vs. running the sequence during
HPD processing). The connect will succeed even if the display is not
connected to begin with (or disappears during the suspended state) since
for legacy ports the PORT_TX_DFLEXDPPMS / DP_PHY_MODE_STATUS_COMPLETED
flag is always set (as opposed to the USB DP alternate mode where it
gets set only when a display is connected).
Correspondingly run the TypeC PHY disconnect sequence during system
suspend and driver unloading. For the unloading case I had to split
up intel_dp_encoder_destroy() to be able to have the 1. flush any
pending encoder work, 2. disconnect TC PHY, 3. call DRM core cleanup and
kfree on the encoder object.
For now run the PHY disconnect during suspend only for TypeC legacy
ports. We will need to disconnect even in USB DP alternate mode in the
future, but atm we don't have a way to reconnect the port in this mode
during resume if the display disappears while being suspended. So for
now punt on this case.
Note that we do not disconnect the port during runtime suspend; in
legacy mode there are no shared HW resources (PHY lanes) with other HW
blocks (USB), so no need to release / reacquire these resources as with
USB DP alternate mode. The only reason to disconnect legacy ports during
system suspend is that the PORT_TX_DFLEXDPPMS /
DP_PHY_MODE_STATUS_COMPLETED flag must be rechecked and the port must be
connected again during system resume. We'll also have to turn the check
for this flag into a poll, after figuring out what's the proper timeout
value for it.
v2:
- Remove the redundant special casing of legacy mode when doing a
disconnect in icl_tc_port_connected(). It's guaranteed already that we
won't disconnect legacy ports in that function.
- Add a note about the new intel_ddi_encoder_destroy() hook.
- Reword the commit message after switching to the VBT based detection.
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108070
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=108924
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-4-imre.deak@intel.com
This is needed by the next patch to determine if a DDI TypeC port is
physically wired to a legacy DP or legacy HDMI connector or if the port
is wired to a USB-C/Thunderbolt connector.
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-3-imre.deak@intel.com
It's useful to see at which point a TypeC port gets disconnected, so add
a debug print for it.
Cc: Paulo Zanoni <paulo.r.zanoni@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181214182703.18865-2-imre.deak@intel.com
Having completed a test run of gem_eio across all machines in CI we also
observe the phenomenon (of lost interrupts after resetting the GPU) on
gen3 machines as well as the previously sighted gen6/gen7. Let's apply
the same HWSTAM workaround that was effective for gen6+ for all, as
although we haven't seen the same failure on gen4/5 it seems prudent to
keep the code the same.
As a consequence we can remove the extra setting of HWSTAM and apply the
register from a single site.
v2: Delazy and move the HWSTAM into its own function
v3: Mask off all HWSP writes on driver unload and engine cleanup.
v4: And what about the physical hwsp?
v5: No, engine->init_hw() is not called from driver_init_hw(), don't be
daft. Really scrub HWSTAM as early as we can in driver_init_mmio()
v6: Rename set_hwsp as it was setting the mask not the hwsp register.
v7: Ville pointed out that although vcs(bsd) was introduced for g4x/ilk,
per-engine HWSTAM was not introduced until gen6!
References: https://bugs.freedesktop.org/show_bug.cgi?id=108735
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181218102712.11058-1-chris@chris-wilson.co.uk
In August 2018 the BSPEC changed the ICL port programming sequence to
closely resemble earlier gen programming sequence. Restrict combo phy to
HBR max rate unless eDP panel is connected to port.
v2: remove debug code that Imre found
v3: simplify translation table if-else
v4: edp translation table now based on link rate and low_swing
v5: Misc review comments + r-b
BSpec: 21257
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Signed-off-by: Clint Taylor <clinton.a.taylor@intel.com>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/1545084827-5776-1-git-send-email-clinton.a.taylor@intel.com
When the pipe_config's update_pipe flag is set we may need to update the
panel fitting settings. On GEN9+ this means we need to update the crtc's
scaler settings.
This fixes the following WARN_ON, during i915 loading on an Asrock
B150M Pro4S/D3 board with an i5-6500 CPU / graphics:
[drm:pipe_config_err [i915]] *ERROR* mismatch in pch_pfit.enabled
(expected no, found yes)
pipe state doesn't match!
WARNING: CPU: 3 PID: 305 at drivers/gpu/drm/i915/intel_display.c:12084
With line 12084 being the I915_STATE_WARN call inside the
"if (!intel_pipe_config_compare())" block in verify_crtc_state().
On this board with 2 1920x1080 monitors connected over HDMI the GOP
initializes both monitors at 1920x1080 and despite no scaling being
necessary configures a scaler for one of them.
When booting with fastboot=1 on the initial modeset needs_modeset will
be false while update_pipe is true. Since we were not calling
skl_update_scaler_crtc() in this case we would leave the scaler enabled
causing this error.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181217141903.4182-1-hdegoede@redhat.com
We have an update for HuC for BXT.
Load the latest version.
v2: Change the subject.
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Anusha Srivatsa <anusha.srivatsa@intel.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207182840.9292-2-anusha.srivatsa@intel.com
DSC can be supported per DP connector. This patch adds a per connector
debugfs node to expose DSC support capability by the kernel.
The same node can be used from userspace to force DSC enable.
force_dsc_en written through this debugfs node is used to force
DSC even for lower resolutions.
Credits to Ville Syrjala for suggesting the proper locks to be used
and to Lyude Paul for explaining how to use them in this context
v8:
* Add else if (ret) for drm_modeset_lock (Lyude)
v7:
* Get crtc, crtc_state from connector atomic state
and add proper locks and backoff (Ville, Chris Wilson, Lyude)
(Suggested-by: Ville Syrjala <ville.syrjala@linux.intel.com>)
* Use %zu for printing size_t variable (Lyude)
v6:
* Read fec_capable only for non edp (Manasi)
v5:
* Name it dsc sink support and also add
fec support in the same node (Ville)
v4:
* Add missed connector_status check (Manasi)
* Create i915_dsc_support node only for Gen >=10 (manasi)
* Access intel_dp->dsc_dpcd only if its not NULL (Manasi)
v3:
* Combine Force_dsc_en with this patch (Ville)
v2:
* Use kstrtobool_from_user to avoid explicit error checking (Lyude)
* Rebase on drm-tip (Manasi)
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Cc: Anusha Srivatsa <anusha.srivatsa@intel.com>
Cc: Lyude Paul <lyude@redhat.com>
Signed-off-by: Manasi Navare <manasi.d.navare@intel.com>
Reviewed-by: Lyude Paul <lyude@redhat.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181206005407.4698-1-manasi.d.navare@intel.com
SFC (Scaler & Format Converter) units are shared between VD and VEBoxes.
They also happen to have separate reset bits. So, whenever we want to reset
one or more of the media engines, we have to make sure the SFCs do not
change owner in the process and, if this owner happens to be one of the
engines being reset, we need to reset the SFC as well.
This happens in 4 steps:
1) Tell the engine that a software reset is going to happen. The engine
will then try to force lock the SFC (if currently locked, it will
remain so; if currently unlocked, it will ignore this and all new lock
requests).
2) Poll the ack bit to make sure the hardware has received the forced
lock from the driver. Once this bit is set, it indicates SFC status
(lock or unlock) will not change anymore (until we tell the engine it
is safe to unlock again).
3) Check the usage bit to see if the SFC has ended up being locked to
the engine we want to reset. If this is the case, we have to reset
the SFC as well.
4) Unlock all the SFCs once the reset sequence is completed.
Obviously, if we are resetting the whole GPU, we don't have to worry
about all of this.
BSpec: 10989
BSpec: 10990
BSpec: 10954
BSpec: 10955
BSpec: 10956
BSpec: 19212
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-4-chris@chris-wilson.co.uk
In Gen11, only even numbered "logical" VDBoxes are hooked up to an SFC
(Scaler & Format Converter) unit. We will use this information to decide
when the SFC units need to be reset.
BSpec: 20189
Signed-off-by: Tomasz Lis <tomasz.lis@intel.com>
Signed-off-by: Oscar Mateo <oscar.mateo@intel.com>
Signed-off-by: Michel Thierry <michel.thierry@intel.com>
Signed-off-by: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Michel Thierry <michel.thierry@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-3-chris@chris-wilson.co.uk
We currently require that our per-engine reset can be called from any
context, even hardirq, and in the future wish to perform the device
reset without holding struct_mutex (which requires some lockless
shenanigans that demand the lowlevel intel_reset_gpu() be able to be
used in atomic context). Test that we meet the current requirements by
calling i915_reset_engine() from under various atomic contexts.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-2-chris@chris-wilson.co.uk
After declaring a terminally wedged device, we allow ourselves to
recover on the next GPU reset (manually triggered), or resume. Check
that resetting a wedged device does work.
v2: Add rpm (taken explicitly in the subtest in case we remove the outer
wakeref) and early warning to i915_reset() for missed wakerefs
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181213091522.2926-1-chris@chris-wilson.co.uk
Define IS_GEN() similarly to our IS_GEN_RANGE(). but use gen instead of
gen_mask to do the comparison. Now callers can pass then gen as a parameter,
so we don't require one macro for each gen.
The following spatch was used to convert the users of these macros:
@@
expression e;
@@
(
- IS_GEN2(e)
+ IS_GEN(e, 2)
|
- IS_GEN3(e)
+ IS_GEN(e, 3)
|
- IS_GEN4(e)
+ IS_GEN(e, 4)
|
- IS_GEN5(e)
+ IS_GEN(e, 5)
|
- IS_GEN6(e)
+ IS_GEN(e, 6)
|
- IS_GEN7(e)
+ IS_GEN(e, 7)
|
- IS_GEN8(e)
+ IS_GEN(e, 8)
|
- IS_GEN9(e)
+ IS_GEN(e, 9)
|
- IS_GEN10(e)
+ IS_GEN(e, 10)
|
- IS_GEN11(e)
+ IS_GEN(e, 11)
)
v2: use IS_GEN rather than GT_GEN and compare to info.gen rather than
using the bitmask
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-2-lucas.demarchi@intel.com
RANGE makes it longer, but clearer. We are also going to add a macro to
check an individual gen, so add the _RANGE prefix here.
Diff generated with:
sed 's/IS_GEN(/IS_GEN_RANGE(/g' drivers/gpu/drm/i915/{*/,}*.{c,h} -i
v2: use IS_GEN rather than GT_GEN
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212181044.15886-1-lucas.demarchi@intel.com
During DDB allocation, we try to distribute enough blocks for each plane
to hit the highest watermark level; if that fails, we retry each lower
level (which should require fewer blocks) until we find one that's
possible (or until the whole commit is rejected as impossible). We need
to reset our running block count when trying each lower level, otherwise
all lower levels will fail as well.
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Fixes: d8e8749802 ("drm/i915: Switch to level-based DDB allocation algorithm (v5)")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181212191720.3706-1-matthew.d.roper@intel.com
It's not just GEN9 platforms that allow for pipes to be disabled via
the DFSM register, but all later platforms as well.
v2: drop pointless parentheses (Ville)
Signed-off-by: Bob Paauwe <bob.j.paauwe@intel.com>
Acked-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Matt Roper <matthew.d.roper@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211192545.140081-1-bob.j.paauwe@intel.com
The DDB allocation algorithm currently used by the driver grants each
plane a very small minimum allocation of DDB blocks and then divies up
all of the remaining blocks based on the percentage of the total data
rate that the plane makes up. It turns out that this proportional
allocation approach is overly-generous with the larger planes and can
leave very small planes wthout a big enough allocation to even hit their
level 0 watermark requirements (especially on APL, which has a smaller
DDB in general than other gen9 platforms). Or there can be situations
where the smallest planes hit a lower watermark level than they should
have been able to hit with a more equitable division of DDB blocks, thus
limiting the overall system sleep state that can be achieved.
The bspec now describes an alternate algorithm that can be used to
overcome these types of issues. With the new algorithm, we calculate
all plane watermark values for all wm levels first, then go back and
partition a pipe's DDB space second. The DDB allocation will calculate
what the highest watermark level that can be achieved on *all* active
planes, and then grant the blocks necessary to hit that level to each
plane. Any remaining blocks are then divided up proportionally
according to data rate, similar to the old algorithm.
There was a previous attempt to implement this algorithm a couple years
ago in bb9d85f6e9 ("drm/i915/skl: New ddb allocation algorithm"), but
some regressions were reported, the patch was reverted, and nobody
ever got around to figuring out exactly where the bug was in that
version. Our watermark code has evolved significantly in the meantime,
but we're still getting bug reports caused by the unfair proportional
algorithm, so let's give this another shot.
v2:
- Make sure cursor allocation stays constant and fixed at the end of
the pipe allocation.
- Fix some watermark level iterators that weren't handling the max
level.
v3:
- Ensure we don't leave any DDB blocks unused by using DIV_ROUND_UP+min
to calculate the extra blocks for each plane. (Ville)
- Replace a while() loop with a for() loop to be more consistent with
surrounding code. (Ville)
- Clean unattainable watermark levels with memset rather than directly
clearing the member fields. Also do the same for the transition
watermark values if they can't be achieved. (Ville)
- Drop min_disp_buf_needed calculations in skl_compute_plane_wm() since
the results are no longer needed or used. (Ville)
- Drop skl_latency[0] != 0 sanity check; both watermark methods already
account for an invalid 0 latency by returning FP_16_16_MAX. (Ville)
v4:
- Break DDB allocation loop when total_data_rate=0 rather than
alloc_size=0. If total_data_rate has dropped to 0, all remaining
planes are disabled, which isn't true for alloc_size (we might just
have not had any remaining blocks to hand out). Plus
total_data_rate=0 is the case we need to avoid to a prevent a
div-by-0. (Ville)
- s/DIV_ROUND_UP/DIV64_U64_ROUND_UP/ to prevent 32-bit breakage (Ville)
v5:
- Don't forget to move 'start' pointer forward for UV surface when
setting plane DDB boundaries. (Ville)
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=105458
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-2-matthew.d.roper@intel.com
The bspec gives an if/else chain for choosing whether to use "method 1"
or "method 2" for calculating the watermark "Selected Result Blocks"
value for a plane. One of the branches of the if chain is:
"Else If ('plane buffer allocation' is known and (plane buffer
allocation / plane blocks per line) >=1)"
Since our driver currently calculates DDB allocations first and the
actual watermark values second, the plane buffer allocation is known at
this point in our code and we include this test in our driver's logic.
However we plan to soon move to a "watermarks first, ddb allocation
second" sequence where we won't know the DDB allocation at this point.
Let's drop this arm of the if/else statement (effectively considering
the DDB allocation unknown) as an independent patch so that any
regressions can be more accurately bisected to either the different
watermark value (in this patch) or the new DDB allocation (in the next
patch).
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181211173107.11068-1-matthew.d.roper@intel.com
Try to be more consistent about intel_* types rather than drm_* types
for lower-level driver functions. While we're at it, let's also be more
consistent with state variable naming (half of the platforms use the
name 'state' whereas the other half used 'crtc_state').
While we're touching these variables, let's also be more consistent
about always naming the intel_crtc_state's "crtc_state" rather than
"state" so that different platform types aren't using different naming
conventions.
v2:
- s/state/crtc_state/ for consistency between platform types (Ville)
- Drop the crtc parameter to intel_color_check(); we can just pull that
out of the state object.
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210215415.19854-2-matthew.d.roper@intel.com
Try to be more consistent about intel_* types rather than drm_* types
for lower-level driver functions.
v2:
- Also drop the intel_crtc parameter from compute_intermediate_wm()
since we can just extract it from the crtc_state parameter. (Ville)
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181210215415.19854-1-matthew.d.roper@intel.com
SKL+ do not use crtc_state->update_wm_pre, so there is absolutely no
point it setting it. crtc_state->update_wm_pre only exists as a
temporary hack for pre-g4x platforms until we redo their
watermarks to be be atomic.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113172330.26069-3-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
skl_compute_wm() wants to compare the old and new watermarks. Currently
it gets at the old watermarks via crtc->state, which is confusing since
it can point at either the old or the new state depending on where
in the sequence we are. In this case it is correct since we have not yet
swapped the states, but let's make it super clear what this is doing
by using the explicit old state.
Cc: Stanislav Lisovskiy <stanislav.lisovskiy@intel.com>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181113172330.26069-1-ville.syrjala@linux.intel.com
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Adding an extra MI_STORE_DWORD_IMM to the gpu relocation path for gen3
was good, but still not good enough. To survive 24+ hours under test we
needed to perform not one, not two but three extra store-dw. Doing so
for each GPU relocation was a little unsightly and since we need to
worry about userspace hitting the same issues, we should apply the dummy
store-dw into the EMIT_FLUSH.
Fixes: 7dd4f6729f ("drm/i915: Async GPU relocation processing")
References: 7fa28e1469 ("drm/i915: Write GPU relocs harder with gen3")
Testcase: igt/gem_tiled_fence_blits # blb/pnv
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207134037.11848-1-chris@chris-wilson.co.uk
Although commit fb6f0b64e4 ("drm/i915: Prevent machine hang from
Broxton's vtd w/a and error capture") applied cleanly after a 24 month
hiatus, the code had moved on with new methods for peeking and fetching
the captured gpu info. Make sure we catch all uses of the stashed error
state and avoid dereferencing the error pointer.
v2: Move error pointer determination into i915_gpu_capture_state
v3: Restore early check to avoid capturing and then throwing away
subsequent GPU error states.
Fixes: fb6f0b64e4 ("drm/i915: Prevent machine hang from Broxton's vtd w/a and error capture")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20181207110554.19897-1-chris@chris-wilson.co.uk
Jani Nikula