This patch adds support for the PCI-8604PW card equipped with four 878A.
It is unknown who the manufacturer of this card is and no drivers were
available during development of the patch. According to images found
online, the card is originally sold with Linux DVR software.
A CPLD on the card prevents the 878A from requesting access to the
bus until an initialization sequence has been issued via GPIOs. The
implemented sequence uses the minimum number of GPIOs needed to
successfully unlock bus access. As there are many more GPIOs connected
to the CPLD, it is very likely that some of the others have an influence
on the bus arbitration scheduling. This should be investigated further
in case of performance issues.
The tested card contains an EEPROM on one of the 878A, but it is
completely empty (i.e. contains only 0xff), so it is not possible
to detect the card.
Signed-off-by: Daniel Glöckner <daniel-gl@gmx.net>
Tested-by: Robert Longbottom <rongblor@googlemail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
New board addition. No other changes.
[m.chehab@samsung.com: rebase patch and fix whitespace mangling]
Signed-off-by: Pojar George <geoubuntu@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
I am no longer available at the kernellabs.com or m1k.net email
addresses. Update each instance of my email to my linuxtv.org
account.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Kodicom 4400R and Geovision GV-800 code in bttv driver abuses mbox_we (int)
in struct bttv as char *.
Remove this hack and add a proper sw_status array to struct bttv instead.
This is a a preparation to remove mbox_we.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Add CyberVision CV06 4-camera card (from CyberVision SV card kit):
http://www.cybervision.com.tw/products-swcard_kits-sv.html
There are some interesting things on the card but they're not supported:
4 LEDs, a connector with 4 IN and 4 OUT pins, RESET IN and RESET OUT
connectors, a relay and CyberVision CV8088-SV16 chip
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add support for noname Bt848 capture-only card (3x composite, 1x S-VHS)
with 14MHz crystal:
http://www.rainbow-software.org/images/hardware/bt848_.jpg
14MHz PLL was not supported by bttv driver until now.
[mchehab@redhat.com: CodingStyle fixes]
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a proper card entry for this device, rather than abusing entries that are
not-quite-right.
Regards,
Hans
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
'audio_input' better describes the meaning of this field.
Signed-off-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Probe for additional tvaudio devices, and allow tvaudio+tda7432 to
co-exist. My STB TV PCI FM bttv card has a tda7432, a tda9850 and a
tea6420 and with this patch it finally works again (probably for the
first time in many years).
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Note that the private chroma agc control has been replaced with the standard
CHROMA_AGC control.
Also fixes a mute/automute problem where closing the file handle would force
mute on. That's not what you want since that would make the mute state out of
sync with the mute control. Instead check against the user count.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Cc: Mauro Carvalho Chehab <mchehab@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Daniel Glöckner
