For TI power management chip TPS40422, READ_TEMPERATURE_2 command is supported on
page 1 of the chip, but the original driver(pmbus.c) only tried to detect this command
on page 0, this will lead to a result that the temperature sensor in page 1 couldn't
be detected. This change is to isolate the tps40422 driver from pmbus.c into a solo
front-end driver.
Signed-off-by: Zhu Laiwen <richard.zhu@nsn.com>
[Guenter Roeck: Dropped unnecessary license text (fixes checkpatch warning)]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The chip's programming interface is quite similar to LTC3880
and supports the same set of sensors.
Reviewed-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
LTC2974 datasheet revision C lists the chip ID for LTC2974 as 0x0213.
Reviewed-by: Robert Coulson <rob.coulson@gmail.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some chips use different exponents for sensors on different pages
or rails. Detect and store exponent per page to support this situation.
This fixes a problem with wrong voltages seen on UCD90120.
Reported-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Tested-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
pmbus code currently crashes the kernel if it detects an internal
implementation error. While the detected condition suggests that there
is a bug in the code, it is hardly fatal. Therefore, it should not
trigger a crash. Replace BUG() with WARN().
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Initialize device specific coefficients from table instead of hard-coding it
to simplify adding additional chips.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Limits on all supported sensors and chips have to be within 0..0x0fff,
and limits are always positive.
Clamp written values in chip driver. Also clear value cache to ensure
that the actually written value is read back and reported correctly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far the driver reported the voltage on VAUX as "vout2". This was not
entirely appropriate as it is not an output voltage, and complicates
the code. Use the new virtual "VMON" register set and report the voltage
as "vmon" instead.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Use u16 instead of int to store cached limit attributes.
This reduces allocated data size per driver instance by 48 bytes.
Use defines for the number of pages supported by individual chips.
Use ARRAY_SIZE for loops to initialize array variables, and
initialize all variables in the same code block.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
On LTC2978, only READ_TEMPERATURE is supported. It reports
the internal junction temperature. This register is unpaged.
On LTC3880, READ_TEMPERATURE and READ_TEMPERATURE2 are supported.
READ_TEMPERATURE is paged and reports external temperatures.
READ_TEMPERATURE2 is unpaged and reports the internal junction
temperature.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
If krealloc() returns NULL, it *doesn't* free the original. So any code
of the form 'foo = krealloc(foo, …);' is almost certainly a bug.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
We read the chip ID from the chip, use it to determine if the chip ID provided
to the driver is correct, and report it if wrong. We should also use the
correct chip ID to select supported functionality.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
Peak attributes were not initialized and cleared correctly.
Also, temp2_max is only supported on page 0 and thus does not need to be
an array.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.2+
Acked-by: Jean Delvare <khali@linux-fr.org>
Rearranged some data structures, and merged some common functions.
Overall code and data size reduction by more than 900 bytes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX34460 is a PMBus 12-Channel Voltage Monitor & Sequencer.
MAX34461 is a PMBus 16-Channel Voltage Monitor & Sequencer.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Not all PMBus devices support the byte status register at 0x78.
Try to use the word status register at 0x79 instead if that is the case.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some of the ZL6100 compatible chips support monitoring a separate voltage pin,
VMON (ZL2004) or VDRV (ZL91xx). Report it as in2 / vmon.
The chips support implicit warning limits for VMON/VDRV, as percentage of the
respective critical voltage. Support by reading/writing the critical voltages
and calculating the associated warning voltages.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
For PMBus chips, modifying one limit register may affect other limits.
Since limits are all cached in the PMBus core driver, related changes
are not reflected in reported limits.
Introduce function to clear the attribute cache. After calling this function,
the core pmbus driver re-reads all cached values.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Some PMBus chips support monitoring an additional non-standard voltage. While
this voltage can in many cases be supported by simulating an additional sensor
page, this does not work in all cases. Specifically, it is problematic if the
data format is linear and the voltage is reported in LINEAR11 format. Since
output voltages use LINEAR16, and the exponent for LINEAR16 data is chip-wide
and fixed, this can result in overflows.
To solve this problem, add support for an additional virtual input voltage,
call it 'vmon', and treat this voltage as input voltage (which, when the chip
supports linear data format, uses LINEAR11).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
So far, attribute memory was allocated by pre-calculating the maximum possible
amount of attributes. Not only does this waste memory, it is also risky because
the calculation might be wrong. It also requires a lot of defines to specify
the maximum number of attributes per class.
Allocate attribute memory using krealloc() instead. That means we have to use
kfree(), since devm_krealloc() does not exist, but that is still less costly
and less risky than trying to predict the number of attributes at the beginning.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since memory is now allocated with dev_ functions, we no longer need to keep
track of allocated memory. Sensor memory allocation can therefore be
simplified significantly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Boolean handling depends on storing the sensor data index in sensor_device_attr
as part of the index variable. This limits the number of sensor attributes to
256, and means the sensor sequence number actually has to be maintained to be
able to access sensor data from boolean functions.
Rework the code to store sensor pointers in the pmbus_boolean data structure
directly. With this approach, the number of supportable sensors is now
unlimited.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Since memory is now allocated with dev_ functions, we no longer need to keep
track of allocated memory. Memory allocation for booleans and labels can
therefore be simplified substantially by allocating it only as needed.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Fix:
ERROR: Macros with multiple statements should be enclosed in a do - while loop
by unwinding the problematic macros.
As a side effect, this patch reduces code size on x86_64 by 160 bytes and bss
size by 64 bytes.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
SENSORS_LIMIT and the generic clamp_val have the same functionality,
and clamp_val is more efficient.
This patch reduces text size by 9052 bytes and bss size by 11624 bytes
for x86_64 builds.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: George Joseph <george.joseph@fairview5.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
This config item has not carried much meaning for a while now and is
almost always enabled by default. As agreed during the Linux kernel
summit, remove it.
CC: Guenter Roeck <linux@roeck-us.net>
CC: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
These drivers use no sleep or delay functions so they don't need to
include <linux/delay.h>.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Cc: Rudolf Marek <r.marek@assembler.cz>
Many hwmon drivers use jiffies but omit the inclusion of the header
file. Fix that, and also fix one driver which was including the header
file but didn't need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Luca Tettamanti <kronos.it@gmail.com>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
Some configurations produce the following compiler warning:
drivers/hwmon/pmbus/pmbus_core.c: In function 'pmbus_show_boolean':
drivers/hwmon/pmbus/pmbus_core.c:752: warning: 'val' may be used uninitialized in this function
While this is a false positive, it can easily be fixed by overloading the return
value from pmbus_get_boolean with both val and error return code (val is a
boolean and thus never negative).
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
ZL9101M and ZL9117M are compatible to ZL6100. Add support to the zl6100 driver.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Add PMBUS_VIRT_READ_TEMP_AVG, PMBUS_VIRT_READ_TEMP2_AVG,
PMBUS_VIRT_READ_POUT_AVG, PMBUS_VIRT_READ_POUT_MAX,
and PMBUS_VIRT_RESET_POUT_HISTORY.
We'll need those for MAX34446.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MDT040 is supported by the generic PMBus driver. Add device ID and reference to
datasheet. Also mention Lineage Power device support in Kconfig.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
TPS40400 and TPS40422 are supported by the generic PMBus driver.
Add device IDs and data sheet references.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
MAX34440 and compatibles support reporting the lowest measured output voltage.
Add support for it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Since devm_kzalloc() is now used to allocate driver memory, the client
driver remove function has no purpose other than to call pmbus_do_remove().
This means we can get rid of it by redefining pmbus_do_remove() to use the
same prototype, and pointing to it directly.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
This patch converts the drivers in drivers/hwmon/* to use the
module_i2c_driver() macro which makes the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Corentin Labbe <corentin.labbe@geomatys.fr>
Cc: Dirk Eibach <eibach@gdsys.de>
Cc: "Mark M. Hoffman" <mhoffman@lightlink.com>
Cc: Steve Glendinning <steve.glendinning@smsc.com>
Cc: Riku Voipio <riku.voipio@iki.fi>
Cc: Guillaume Ligneul <guillaume.ligneul@gmail.com>
Cc: David George <david.george@ska.ac.za>
Cc: "Hans J. Koch" <hjk@hansjkoch.de>
Cc: Marc Hulsman <m.hulsman@tudelft.nl>
Cc: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
strict_strtol is deprecated and results in a checkpatch warning.
Replace it with kstrtol.
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Intersil reports that all chips supported by the zl6100 driver require
an interval between chip accesses, even ZL2004 and ZL6105 which were thought
to be safe.
Reported-by: Vivek Gani <vgani@intersil.com>
Cc: stable@vger.kernel.org # 3.2+
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
A global delay parameter has the side effect of being overwritten with 0 if a
single ZL2004 or ZL6105 is instantiated. If other chips supported by the same
driver are in the system, this will result in access errors for those chips.
To solve the problem, keep a per-instance copy of the delay parameter, and do
not change the original parameter.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Cc: stable@vger.kernel.org # 3.1+
Acked-by: Jean Delvare <khali@linux-fr.org>
There are up to three POUT alarm attributes, not two, since cap_alarm was added.
Reported-by: Michele Petracca <mi.petracca@gmail.com>
Cc: stable@vger.kernel.org # 3.0+ [3.0 will need backport]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Temperature history is reset by writing 0x8000 into the peak temperature
register, not 0xffff.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
BMR4xx devices don't have an external temperature sensor,
and instantiating it does not provide value anyway if it is disabled.
Only instantiate it if it is enabled.
Also optimize wait time between I2C chip accesses in the probe function, and
replace unnecessary check for support for I2C_FUNC_SMBUS_READ_BYTE_DATA with
now required support for I2C_FUNC_SMBUS_READ_WORD_DATA.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for Ericsson BMR450, BMR451, BMR462, BMR463, and BMR464, which are
based on ZL2005 and ZL2008, to zl6100 driver. Remove BMR450 and BMR451 device
IDs from generic PMBus driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add explicit support for ZL2005. Functionality is almost the same as with other
Zilker Labs / Intersil chips, but limit register detection does not work reliably.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Since manufacturer and device ID are known, read and validate it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
[Dan Carpenter <dan.carpenter@oracle.com>: Fixed memory leak]
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Shift operations can be used for sign extensions. Use it.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add device IDs and reference to datasheets for Lineage Power DC-DC converters.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
The LTC3880 PMBus command set is comparable to LTC2978. Add support for it
to the LTC2978 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Provide explicit driver for LTC2978 to enable support for minimum and peak
attributes. Remove ltc2978 chip id from generic pmbus driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
At least one PMBus chip supports peak attributes for READ_TEMPERATURE2.
Add virtual registers to be able to report it to the user.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Always call _pmbus_read_byte() instead of pmbus_read_byte() in PMBus core
driver. With this change, device specific read functions can be implemented for
all registers.
Since the device specific read_byte function is now always called, we need to be
more careful with page validations. Only fail if the passed page number is larger
than 0, since -1 means "current page".
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
EINVAL was over-used in the code. Replace it with more appropriate errors.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
ADM1276 is mostly compatible to ADM1275, with added support for input power
measurement. Add support for it to the ADM1275 driver.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
ADM1275 supports a second current limit, which can be configured as either lower
or upper limit. Add support for it and report it as either lower or upper
critical current limit.
Also replace error return code EINVAL for unsupported pages with ENXIO as this
is more appropriate for the observed condition.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Driver remove functions have an error return value, but rarely return an error
in practice. If a driver does return an error from its remove function, the
driver won't be unloaded and is expected to stay alive.
pmbus_do_remove() is defined as returning an int, but always returns 0 (no
error). Calling code passes that return value on to high level driver
remove functions, but does not evaluate it and removes driver data even if
pmbus_do_remove() returned an error (which it in practice never does). Even if
this code could never cause a real problem, it is nevertheless conceptually
wrong.
To reduce confusion and simplify the code, change pmbus_do_remove() to be a void
function, and have PMBus client drivers always return zero in their driver
remove functions.
Reported-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Return values for functions reading/writing manufacturer specific registers are
poorly explained. Add comments to improve documentation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Temperature alarms are detected by checking the alarm bit and comparing
temperature limits against the current temperature. For low limits, this
comparison needs to be reversed (temp < limit instead of temp > limit).
This was not taken into account, resulting in wrong alarms if a temperature
fell below a low limit.
Fix by adding a low limit flag in the limit data structure. When creating the
sensor entry, the order of registers to compare is now reversed for low limits.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Cc: stable@kernel.org # 3.0+
Rewrite the loop walking the id array during probe. The new code is
better adapted to a null-terminated array, and is also clearer and
more efficient than the original.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Axel Lin <axel.lin@gmail.com>
Cc: Guenter Roeck <guenter.roeck@ericsson.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
pmbus_clear_faults() attempts to clear faults on non-existing real pages.
As a result, the command error bit in the status register is set, and faults
are not really cleared.
All byte writes to non-zero pages are requests to clear the status register
on that page. Since non-zero pages are virtual and do not exist on the chip,
there is nothing to do, and such requests have to be ignored. This fixes
above problem.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
With virtual pages and to be able to handle more chips, it is necessary to
virtualise pmbus_write_byte().
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage, current, and temperature peak (historic maximum)
attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and temperature peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add support for voltage and current peak (historic maximum) attributes.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Most PMBus devices provide manufacturer specific commands to read low and/or
high peak values for some or all of its sensors.
To support providing those values as lowest/highest attributes to the user,
introduce virtual PMBus commands. Those commands reside outside the normal
command set and have to be implemented in device specific code, which map the
virtual commands to device specific commands.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
With virtual register page support, it is now possible that the status register
on virtual pages does not exist or is itself virtual. To take this into account
when creating alarm attributes, generate those attributes only if the status
register on the respective page is known to exist.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some PMBus chips have non-standard sensor registers. An easy way to
support such sensors is to introduce virtual pages and map the non-standard
registers into standard registers on an extra page.
For this to work, the code verifying if the configured number of pages exists
has to be removed. Since a wrong number of pages can only be configured in a
front-end driver, this should not have a practical impact since the resulting
errors should be found during development and testing.
Also, functions to read the chip status while checking if a command register
exists must be modified to no longer set the page register before reading the
status, since the physical page associated with the checked register may not
exist. This does not make a functional difference since the page was already set
when the attempt to read the register was made.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some PMBus devices use non-standard registers for some of the sensors and/or
limits. To support such devices, add code to support reading and writing of word
size registers in device specific code.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Some hwmon sysfs attributes have a length of 20 bytes (plus terminating 0).
I2C_NAME_SIZE is defined as 20 and thus can not be used to define the length
of hwmon sysfs attributes. Replace it with PMBUS_NAME_SIZE, set to 24.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Add ADP4000, NCP4200 and NCP4208 to the list of devices supported by the generic
PMBus driver, and add device IDs to enable explicit instantiation.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
In VID mode, output voltages are measured and reported as VID values, and
have to be converted to voltages using VID conversion tables or functions.
Support is added for VR11 only at this time.
This patch enables support for PMBus devices supporting VID VR11 based output
voltage selection such as NCP4200 and NCP4208.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Since the number of PMBus drivers is getting large, move them into
directory drivers/hwmon/pmbus to improve readability and scalability.
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
Reviewed-by: Robert Coulson <robert.coulson@ericsson.com>
Zhu, Richard \(NSN - CN/Beijing\)