There are three errors in the transcription of the latest revision to the
B6PHY init specifications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[BRIDGE]: adding new device to bridge should enable if up
[IPV6]: Do not set IF_READY if device is down
[IPSEC]: xfrm audit hook misplaced in pfkey_delete and xfrm_del_sa
[IPSEC]: Add xfrm policy change auditing to pfkey_spdget
[IPSEC]: xfrm_policy delete security check misplaced
[CONNECTOR]: Bugfix for cn_call_callback()
[DCCP]: Revert patch which disables bidirectional mode
[IPV6]: Handle np->opt being NULL in ipv6_getsockopt_sticky().
[UDP]: Reread uh pointer after pskb_trim
[NETFILTER]: nfnetlink_log: fix crash on bridged packet
[NETFILTER]: nfnetlink_log: zero-terminate prefix
[NETFILTER]: nf_conntrack_ipv6: fix incorrect classification of IPv6 fragments as ESTABLISHED
o Fix use of uninitialized variable sec.
o Make the RTC_ALM_SET ioctl return -EINVAL for non-zero seconds - the
DS1286 has no second field for the alarm time.
o Replace the obscure BIN_TO_BCD macro with BIN2BCD.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When system under heavy stress and must allocate new work
instead of reusing old one, new work must use correct
completion callback.
Patch is based on Philipp's and Lars' work.
I only cleaned small stuff (and removed spaces instead of tabs).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] cio: Call cancel_halt_clear even when actl == 0.
[S390] cio: Use path verification to check for path state.
[S390] cio: Fix locking when calling notify function.
[S390] Fixed handling of access register mode faults.
[S390] dasd: Use default recovery for SNSS requests
[S390] check_bugs() should be inline.
[S390] tape: Compression overwrites crypto setting
[S390] nss: disable kexec.
[S390] reipl: move dump_prefix_page out of text section.
[S390] smp: disable preemption in smp_call_function/smp_call_function_on
[S390] kprobes breaks BUG_ON
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
pata_pdc202xx_old: fix data corruption and other problems
pata_legacy: fix io/irq mismatch
ahci: RAID mode SATA patch for Intel ICH9M
For the Freescale M5282 ColdFire,
Port UA Pin Assignment Register should set to UART mode.
Patch submitted by David Wu <davidwu@arcturusnetworks.com>.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tlclk driver is going on the MPCBL005 so I need to make the Kconfig
more more generic. Just some text changes.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Based on a patch from Don Howard <dhoward@redhat.com>
When calling write() with a buffer larger than 512 bytes, the
driver's write buffer overflows, allowing to overwrite the EIP and
execute arbitrary code with kernel privileges.
In read(), there exists a similar problem, but coming from the device.
A malicous or buggy device sending more than 512 bytes can overflow
of the driver's read buffer, with the same effects as above.
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Harald Welte <laforge@gnumonks.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/drzeus/mmc:
sdhci: release irq during suspend
sdhci: make isr tolerant of read errors
mmc: require explicit support for high-speed
ncpfs: make sure server connection survives a kill
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
sis900 warning fixes
mv643xx_eth: Place explicit port number in mv643xx_eth_platform_data
pcnet32: Fix PCnet32 performance bug on non-coherent architecutres
__devinit & __devexit cleanups for de2104x driver
3c59x: Handle pci_enable_device() failure while resuming
dmfe: Fix link detection
dmfe: fix two bugs
dmfe: trivial/spelling fixes
revert "drivers/net/tulip/dmfe: support basic carrier detection"
ucc_geth: returns NETDEV_TX_BUSY when BD ring is full
ucc_geth: Fix BD processing
natsemi: netpoll fixes
bonding: Improve IGMP join processing
bonding: only receive ARPs for us
bonding: fix double dev_add_pack
Change the returned error code to ENOMEM if the connection event
backlog is full. This prevents the ib_cm from issuing a reject
on the connection, which can allow retries to succeed.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix memory region permission problems:
- remove useless and redundant iwch_mem_perms enum.
- create ib_to_tpt_access_rights() for mapping ib access rights
to T3 TPT permissions.
- create ib_to_mwbind_access_rights() for mapping ib access rights
to T3 MWBIND WR permissions.
- fix up the mem reg code to utilize the new functions.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Only print one AE error for a given connection in the kernel log.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Stop the endpoint timer when the MPA exchange is aborted by the peer.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Change iwch_destroy_qp() to always move the QP to ERROR and let
iwch_modify_qp() decide what to do.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fixes for "normal close" failures:
- Start normal close timer when moving to CLOSING state.
- Handle ABORTING state in close_con_rpl().
- Stop timer correctly on abort during a normal close.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
cxgb3 uses dma_alloc_coherent() et al. thus needs linux/dma-mapping.h
include in order to build reliably.
Noticed on sparc64.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct rdma_bind_list fields for hlist are not being initialized,
resulting in a corrupted list. Fix this by using kzalloc() to make
sure all pointers are NULL.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the consumer rejects the connection we end up under-referencing the
endpoint structure. The fix is to call iwch_ep_disconnect() instead
of the low level disconnect functions so that the endpoint close timer
is started correctly.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
initramfs ended up depending on BLOCK:
INITRAMFS_SOURCE <-- BLK_DEV_INITRD <-- BLOCK
This inhibits use of customized-initramfs-over-ramfs without block layer
(ramfs would still be enabled), useful in embedded applications.
Move BLK_DEV_INITRD out of 'drivers/block/Kconfig' and into 'init/Kconfig',
make it unconditional.
Signed-off-by: Dimitri Gorokhovik <dimitri.gorokhovik@free.fr>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for the struct pci_driver shutdown method to cciss.
We require notification of an impending reboot or shutdown so that we can
flush the battery backed write cache (BBWC) on the Smart Array controller.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch changes the way we determine if a logical volume is larger than
2TB.
The original test looked for a total_size of 0. Originally we added 1 to the
total_size. That would make our read_capacity return size 0 for >2TB lv's.
We assumed that we could not have a lv size of 0 so it seemed OK until we were
in a clustered system. The backup node would see a size of 0 due to the
reservation on the drive. That caused the driver to switch to 16-byte CDB's
which are not supported on older controllers. After that everything was
broken.
It may seem petty but I don't see the value in trying to determine if the LBA
is beyond the 2TB boundary. That's why when we switch we use 16-byte CDB's
for all read/write operations. Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix implicit declarations and missing code in atyfb.
drivers/video/aty/atyfb_base.c:2137: warning: implicit declaration of function 'a
ty_ld_lcd'
drivers/video/aty/atyfb_base.c:2154: warning: implicit declaration of function 'a
ty_st_lcd'
atyfb_base.c:(.text+0x33e5c): undefined reference to `aty_ld_lcd'
atyfb_base.c:(.text+0x33eb2): undefined reference to `aty_st_lcd'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drivers/video/nvidia/nv_backlight.c: In function 'nvidia_bl_init':
drivers/video/nvidia/nv_backlight.c:103: error: implicit declaration of function 'pmac_has_backlight_type'
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Cc: James Simmons <jsimmons@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interrupt is shared with another device, which resumes earlier than the
sdhci controller, and generates an interrupt.
The sdhci interrupt handler runs, sees 0xffffffff in its own device's
interrupt status, and tries to handle it.. The reason for the 0xffffffff
is that the device is still suspended, and *all* regs are reading back
0xffffffff.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
The new high-speed timings are similar to each other and the old
system, but not identical. And although things "just work" most of
the time, sometimes it does not. So we need to start marking which
hosts are known to fully comply with the new timings.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
drivers/net/sis900.c: In function 'sis900_reset_phy':
drivers/net/sis900.c:972: warning: 'status' may be used uninitialized in this function
drivers/net/sis900.c: In function 'sis900_check_mode':
drivers/net/sis900.c:1431: warning: 'status' may be used uninitialized in this function
drivers/net/sis900.c: In function 'sis900_timer':
drivers/net/sis900.c:1467: warning: 'status' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We were using the platform_device.id field to identify which ethernet
port is used for mv643xx_eth device. This is not generally correct.
It will be incorrect, for example, if a hardware platform uses a single
port but not the first port. Here, we add an explicit port_number field
to struct mv643xx_eth_platform_data.
This makes the mv643xx_eth_platform_data structure required, but that
isn't an issue since all users currently provide it already.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PCnet32 driver always passed the the size of the largest possible packet
to the pci_dma_sync_single_for_cpu and pci_dma_sync_single_for_device.
This results in a fairly large "colateral damage" in the caches and makes
the flush operation itself much slower. On a system with a 40MHz CPU this
patch increases network bandwidth by about 12%.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Handle pci_enable_device() failure while resuming, we can safely exit here.
Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a oops on module removal due to deallocating memory before unregistring
driver Fix a NULL pointer dereference when dev_alloc_skb fails
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a typo, wrap lines on 80-th column, change KERN_ERR to KERN_INFO for
link status message
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revert 7628b0a8c0. Thomas Bachler
reports:
Commit 7628b0a8c0 (drivers/net/tulip/dmfe:
support basic carrier detection) breaks networking on my Davicom DM9009.
ethtool always reports there is no link. tcpdump shows incoming packets,
but TX is disabled. Reverting the above patch fixes the problem.
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Thomas Bachler <thomas@archlinux.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix broken BD processing code.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix two issues in this driver's netpoll path: one usual, with spin_unlock_irq()
enabling interrupts which nobody asks it to do (that has been fixed recently in
a number of drivers) and one unusual, with poll_controller() method possibly
causing loss of interrupts due to the interrupt status register being cleared
by a simple read and the interrpupt handler simply storing it, not accumulating.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In active-backup mode, the current bonding code duplicates IGMP
traffic to all slaves, so that switches are up to date in case of a
failover from an active to a backup interface. If bonding then fails
back to the original active interface, it is likely that the "active
slave" switch's IGMP forwarding for the port will be out of date until
some event occurs to refresh the switch (e.g., a membership query).
This patch alters the behavior of bonding to no longer flood
IGMP to all ports, and to issue IGMP JOINs to the newly active port at
the time of a failover. This insures that switches are kept up to date
for all cases.
"GOELLESCH Niels" <niels.goellesch@eurocontrol.int> originally
reported this problem, and included a patch. His original patch was
modified by Jay Vosburgh to additionally remove the existing IGMP flood
behavior, use RCU, streamline code paths, fix trailing white space, and
adjust for style.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ARP validation code only needs ARPs for the bonding device.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bonding can erroneously register the same packet_type to receive
ARPs (for use by ARP validation): once at device open time, and once via
sysfs. Since sysfs can change the validate setting (and thus register
or unregister) at any time, a flag is needed to synchronize with device
open in order to avoid double registrations, and the simplest place is
within the packet_type structure itself. Double unregister is not an
issue.
Bug reported by Ulrich Oelmann <ulrich.oelmann@web.de>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix wrong "port" calculations in pdc202xx_{configure_piomode,set_dmamode}()
They were broken for all configurations except one (master device on primary
channel, no other devices) and as a result device settings + PIO/DMA timings
were being programmed into the wrong PCI registers. This could result in
a large variety of problems including data corruption, hangs etc. (depending
on devices used and your luck :-).
ap->port_no ap->devno used PCI registers correct PCI registers
0 0 0x60-0x62 0x60-0x62
0 1 0x62-0x64 0x64-0x66
1 0 0x64-0x66 0x68-0x6a
1 1 0x66-0x68 0x6c-0x6e
Also forward port recent fixes from drivers/ide pdc202xx_old driver:
* fix XFER_MW_DMA0 timings (they were overclocked, use the official ones)
* fix bitmasks for clearing bits of register B:
- when programming DMA mode bit 0x10 of register B was cleared which
resulted in overclocked PIO timing setting (iff PIO0 was used)
- when programming PIO mode bits 0x18 weren't cleared so suboptimal
timings were used for PIO1-4 if PIO0 was previously set (bit 0x10)
and for PIO0/3/4 if PIO1/2 was previously set (bit 0x08)
and finally bump driver version.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_legacy fails to detect the disk on my old ISA/VLB 486:
it starts to probe io=0x1f0 ctr=0x3f6 irq=15, complains
loudly about IDENTIFYs timing out, and finally fails.
(Sorry I couldn't capture the kernel's boot messages.)
It turns out that the driver's mapping from io to irq in
legacy_irq[] is wrong: index 0 for io=0x1f0 has irq=15 but
should have irq=14, and index 1 for io=0x170 has irq=14 but
should have irq=15. This is confirmed by a comparison with
include/asm-i386/ide.h:ide_default_irq().
This patch swaps the first two elements in legacy_irq[],
which makes pata_legacy work on my 486.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds the Intel ICH9M RAID controller DID for SATA support.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The subchannel may just be status pending, even with actl == 0. We
must go through the cancel_halt_clear procedure to put the subchannel
into a defined state.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After I/O has been killed by the common I/O layer, trigger path
verification which will queue cio_device_nopath_notify itself if it
finds a device to be without paths.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure we hold the device lock when we modify the ccw device
structure but always call the notify function without the lock held.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
For extended error reporting we sometimes have to start an
Sense Subsystem Status request (SNSS). When this request needs
to be recovered for some reason, the recovery request will
fail with 'command reject'.
Our usual recovery procedure will retry the failed request by
creating a new request and chaining the failed request from that
one. SNSS requests, though, must not be chained from anything,
so the recovery request will fail permanently.
Use the default recovery for SNSS request, which will just restart
the original request without further ado.
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
After switching compression on/off with the mt command, tape encryption is no
longer working. The reason for that is, that the modeset_byte is set to
the compression value instead of using bitwise and/or bit operations to
enable/disable the corresponding bit.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
I recognized a compile error in latest git:
/here/workdir/git/drivers/net/gianfar.c: In function `gfar_vlan_rx_kill_vid':
/here/workdir/git/drivers/net/gianfar.c:1135: error: structure has no member named `vgrp'
This error was introduced in commit:
commit 6d04e3b04b
...
[VLAN]: Avoid a 4-order allocation.
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
CT based mach64 cards were reported to hang on sparc64 boxes when
compiled with gcc-4.1.x and later.
Looking at this piece of code, it's no surprise. A critical
delay was implemented as an empty for() loop, and gcc 4.0.x
and previous did not optimize it away, so we did get a delay.
But gcc-4.1.x and later can optimize it away, and we get crashes.
Use a real udelay() to fix this. Fix verified on SunBlade100.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replacing use of UTS_RELEASE with utsname()->release avoids that the
usb-storage driver is recompiled each time the kernel version changes.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
"drivers/char/epca.c:2741: warning: 'get_termio' defined but not used"
Signed-off-by: Michal Piotrowski <michal.k.k.piotrowski@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch resolves the issue found here:
http://bugme.osdl.org/show_bug.cgi?id=7426
The basic summary is:
Currently we register most of i386/x86_64 clocksources at module_init
time. Then we enable clocksource selection at late_initcall time. This
causes some problems for drivers that use gettimeofday for init
calibration routines (specifically the es1968 driver in this case),
where durring module_init, the only clocksource available is the low-res
jiffies clocksource. This may cause slight calibration errors, due to
the small sampling time used.
It should be noted that drivers that require fine grained time may not
function on architectures that do not have better then jiffies
resolution timekeeping (there are a few). However, this does not
discount the reasonable need for such fine-grained timekeeping at init
time.
Thus the solution here is to register clocksources earlier (ideally when
the hardware is being initialized), and then we enable clocksource
selection at fs_initcall (before device_initcall).
This patch should probably get some testing time in -mm, since
clocksource selection is one of the most important issues for correct
timekeeping, and I've only been able to test this on a few of my own
boxes.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ipmi_si_intf tries to access default ports, if no device could be found
elsewhere. On PPC we have a function to check, if these legacy IO ports
are accessible. This patch adds a check for these ports on PPC. This
patch fixes a breakage of IPMI module on PPC machines without a BMC.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Corey Minyard <minyard@acm.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Recent patch for raid6 reshape had a change missing that showed up in
subsequent review.
Many places in the raid5 code used "conf->raid_disks-1" to mean "number of
data disks". With raid6 that had to be changed to "conf->raid_disk -
conf->max_degraded" or similar. One place was missed.
This bug means that if a raid6 reshape were aborted in the middle the
recorded position would be wrong. On restart it would either fail (as the
position wasn't on an appropriate boundary) or would leave a section of the
array unreshaped, causing data corruption.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently sm501fb_crtsrc_store() won't allow the routing to be changed via
echos from userspace in to the sysfs file. The reason for this is that the
strnicmp() for both heads uses a sizeof() for the string length, which ends
up being strlen() + 1 (\0 in the normal case, but the echo gives a newline,
which is where the issue occurs), this then causes a mismatch and
subsequently bails with the -EINVAL.
In addition to this, the hardcoded lengths were then used for the store
length that was returned, which ended up being erroneous and resulting in a
write error. There's also no point in returning anything but the full
length since it will -EINVAL out on a mismatch well before then anyways.
sizeof("string") is great for making sure you have space in your buffer,
but rather less so for string comparisons :-)
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove remaining references to saved registers now that
uart_handle_sysrq_char() does not want them.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gpio_keys driver is wrongly ARM-specific; it can't build on
other platforms with GPIO suport. This fixes that problem.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Ben Nizette <ben.nizette@iinet.net.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix soft lockup with iSeries viocd driver, caused by eventually calling
end_that_request_first() with nr_bytes 0.
Some versions of hald do an SG_IO ioctl on the viocd device which becomes a
request with hard_nr_sectors and hard_cur_sectors set to zero. Passing zero
as the number of sectors to end_request() (which calls
end_that_request_first()) causes an infinite loop when the bio is being freed.
This patch makes sure that the zero is never passed. It only requires some
number larger the the request size the terminate the loop.
The lockup is triggered by hald, interrogating the device.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
For devices that do not support msi-x we only support 1 interrupt. Therefore
we can disable that one interrupt by disabling the msi capability itself. If
we leave the intx interrupts disabled while we have the msi capability
disabled no interrupts should be delivered from that device.
Devices with just the minimal msi support (and thus hitting this code path)
include things like the intel e1000 nic, so it looks like is going to be a
fairly common case and thus important to get right.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
enable/disable_msi_mode have several side effects which keeps them from being
generally useful. So this patch replaces them with with two much more
targeted functions: msi_set_enable and msix_set_enable.
This patch makes pci_dev->msi_enabled and pci_dev->msix_enabled the definitive
way to test if linux has enabled the msi capability, and has the appropriate
msi data structures set up.
This patch ensures that while writing the msi messages in save/restore and
during device initialization we have the msi capability disabled so we don't
get into races. The pci spec requires that we do not have the msi capability
enabled and the msi messages unmasked while we write the messages. Completely
disabling the capability is overkill but it is easy :)
Care has been taken so we never have both a msi capability and intx enabled
simultaneously. We haven't run into a problem yet but better safe then sorry.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In some cases when we are not using msi we need a way to ensure that the
hardware does not have an msi capability enabled. Currently the code has been
calling disable_msi_mode to try and achieve that. However disable_msi_mode
has several other side effects and is only available when msi support is
compiled in so it isn't really appropriate.
Instead this patch implements pci_msi_off which disables all msi and msix
capabilities unconditionally with no additional side effects.
pci_disable_device was redundantly clearing the bus master enable flag and
clearing the msi enable bit. A device that is not allowed to perform bus
mastering operations cannot generate intx or msi interrupt messages as those
are essentially a special case of dma, and require bus mastering. So the call
in pci_disable_device to disable msi capabilities was redundant.
quirk_pcie_pxh also called disable_msi_mode and is updated to use pci_msi_off.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Michael Ellerman <michael@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In http://bugzilla.kernel.org/show_bug.cgi?id=8065, Shen points out that the
cyclades driver forget to return closing_wait to userspace.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Shen <shanlu@cs.uiuc.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Enabling the backlight by default appears to cause problems for many
users. This patch disables backlight controls unless explicitly
enabled by users via a module parameter. Since PMAC users are known
to work, default to enabled in that case.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Fix a mix up when the nvidia driver was converted resulting
in the backlight having an incorrect initial brightness.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[VLAN]: Avoid a 4-order allocation.
[HDLC] Fix dev->header_cache_update having a random value.
[NetLabel]: Verify sensitivity level has a valid CIPSO mapping
[PPPOE]: Key connections properly on local device.
[AF_UNIX]: Test against sk_max_ack_backlog properly.
[NET]: Fix bugs in "Whether sock accept queue is full" checking
* master.kernel.org:/home/rmk/linux-2.6-arm: (30 commits)
[ARM] Acorn: move the i2c bus driver into drivers/i2c
[ARM] ARM SCSI: Don't try to dma_map_sg too many scatterlist entries
[ARM] ARM FAS216: don't modify scsi_cmnd request_bufflen
[ARM] rtc-pcf8583: Final fixes for this RTC on RiscPC
[ARM] rtc-pcf8583: correct month and year offsets
[ARM] rtc-pcf8583: don't use BCD_TO_BIN/BIN_TO_BCD
[ARM] EBSA110: Work around build errors
[ARM] 4241/1: Define mb() as compiler barrier on a uniprocessor system
[ARM] 4239/1: S3C24XX: Update kconfig entries for PM
[ARM] 4238/1: S3C24XX: docs: update suspend and resume
[ARM] 4237/2: oprofile: Always allow backtraces on ARM
[ARM] Yet more asm/apm-emulation.h stuff
ARM: OMAP: Add missing get_irqnr_preamble and arch_ret_to_user for omap2
ARM: OMAP: Use linux/delay.h not asm/delay.h
ARM: OMAP: Remove obsolete alsa typedefs
ARM: OMAP: omap1510->15xx conversions needed for sx1
ARM: OMAP: Add missing includes to board-nokia770
ARM: OMAP: Workqueue changes for board-h4.c
ARM: OMAP: dmtimer.c omap1 register fix
ARM: OMAP: board-nokia770: correct lcd name
...
Move the Acorn IOC/IOMD I2C bus driver from drivers/i2c, strip
out the reminants of the platform specific parts of the old
PCF8583 RTC code, and remove the old obsolete PCF8583 driver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
An off-by-one bug meant we were always trying to map one too many
scatterlist entries. This was mostly harmless prior to the checks
going in to consistent_sync(), but now causes the kernel to BUG.
Also, powertec.c was missing an assignment to info->ec.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SCSI doesn't want drivers to modify request_bufflen, so keep a
driver-private copy of this in the scsi_pointer structure instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Replace the I2C bus address, as per drivers/acorn/char/pcf8583.c.
Also, since this driver also contains Acorn RiscPC specific code
for obtaining the current year from the SRAM (and updating the
platform specific checksum when writing new data back) this is
NOT a platform independent driver.
Document it as such, and update the dependencies to reflect this
fact.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Both BCD_TO_BIN(x) and BIN_TO_BCD(x) have an unexpected side-effect -
not only do they return the value as expected, they _modify_ their
argument in the process.
Let's play it safe and avoid these macros.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Use the standard magic.h for kvmfs.
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A bogus 'return r' can cause an otherwise successful module load to fail.
This both denies users the use of kvm, and it also denies them the use of
their machine, as it leaves a filesystem registered with its callbacks
pointing into now-freed module memory.
Fix by returning a zero like a good module.
Thanks to Richard Lucassen <mailinglists@lucassen.org> (?) for reporting
the problem and for providing access to a machine which exhibited it.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Enabling dirty page logging is done using KVM_SET_MEMORY_REGION ioctl.
If the memory region already exists, we need to remove write accesses,
so writes will be caught, and dirty pages will be logged.
Signed-off-by: Uri Lublin <uril@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Since dirty_bitmap is an unsigned long array, the alignment and size need
to take that into account.
Signed-off-by: Uri Lublin <uril@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
A few places where we modify guest memory fail to call mark_page_dirty(),
causing live migration to fail. This adds the missing calls.
Signed-off-by: Uri Lublin <uril@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Allocate a distinct inode for every vcpu in a VM. This has the following
benefits:
- the filp cachelines are no longer bounced when f_count is incremented on
every ioctl()
- the API and internal code are distinctly clearer; for example, on the
KVM_GET_REGS ioctl, there is no need to copy the vcpu number from
userspace and then copy the registers back; the vcpu identity is derived
from the fd used to make the call
Right now the performance benefits are completely theoretical since (a) we
don't support more than one vcpu per VM and (b) virtualization hardware
inefficiencies completely everwhelm any cacheline bouncing effects. But
both of these will change, and we need to prepare the API today.
Signed-off-by: Avi Kivity <avi@qumranet.com>
This reflects the changed scope, from device-wide to single vm (previously
every device open created a virtual machine).
Signed-off-by: Avi Kivity <avi@qumranet.com>
This avoids having filp->f_op and the corresponding inode->i_fop different,
which is a little unorthodox.
The ioctl list is split into two: global kvm ioctls and per-vm ioctls. A new
ioctl, KVM_CREATE_VM, is used to create VMs and return the VM fd.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Larry Finger