Due to a HW issue in PHY info collection rtap_include_phy_info is not
in use, hence can be removed.
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add an of_node_put when a tested device node is not available.
The semantic patch that fixes this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
identifier f;
local idexpression e;
expression x;
@@
e = f(...);
... when != of_node_put(e)
when != x = e
when != e = x
when any
if (<+...of_device_is_available(e)...+>) {
... when != of_node_put(e)
(
return e;
|
+ of_node_put(e);
return ...;
)
}
// </smpl>
Fixes: db878f76b9 ("tee: optee: take DT status property into account")
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Jens Wiklander <jens.wiklander@linaro.org>
Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/i3c/master/dw-i3c-master.c: In function ‘dw_i3c_master_bus_init’:
drivers/i3c/master/dw-i3c-master.c:603:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (ret)
^
drivers/i3c/master/dw-i3c-master.c:605:2: note: here
case I3C_BUS_MODE_PURE:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
ht_idx (ht rate index) and idx (rate table index) are calculated based on
mcs index. This mcs index used in the above calculation should be 0-9 for
getting the correct ht_idx and idx.
Currently the mcs index used for the above calculations is mcs index which
can be 0-31 (in case of HT), leading to incorrect rate index and ht index values.
Fix the issue by obtaining mcs value from the ratecode reported by firmware
and use it for calculating ht_idx and idx (rate-table index).
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e88975ca37 ("ath10k: dump tx stats in rate table format")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SGI is updated wrongly in tx stats table in debugfs per sta
entry. To know whether the packets/bytes are sent with SHORT GI,
test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or
not in the txrate flags.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the bandwidth is updated wrongly in BW table in tx_stats
debugfs per sta as there is difference in number of bandwidth type
in mac80211 and driver stats table. This leads to bandwidth getting
updated at wrong index in bandwidth table in tx_stats.
Fix this index mismatch between mac80211 and driver stats table (BW table)
by making the number of bandwidth type in driver compatible with mac80211.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The NSS data is updated incorrectly in the tx stats as the array
indexing starts from zero.
Fix the incorrect updation of NSS data in tx_stats by taking into
consideration the array index starting from zero.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c: In function '_rtl92s_firmware_downloadcode':
drivers/net/wireless/realtek/rtlwifi/rtl8192se/fw.c:139:17: warning:
variable 'seg_ptr' set but not used [-Wunused-but-set-variable]
It's not used after commit 59ae1d127a ("networking: introduce and use
skb_put_data()")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c: In function '_rtl8723e_dm_bt_coexist_2_ant':
drivers/net/wireless/realtek/rtlwifi/rtl8723ae/hal_btc.c:1408:5: warning:
variable 'bt_retry_cnt' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c: In function 'rtl8723be_dm_check_edca_turbo':
drivers/net/wireless/realtek/rtlwifi/rtl8723be/dm.c:998:7: warning:
variable 'b_last_is_cur_rdlstate' set but not used [-Wunused-but-set-variable]
It's never used and can be removed.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The call to of_find_node_by_phandle returns a node pointer with refcount
incremented thus it must be explicitly decremented after the last
usage.
Detected by coccinelle with the following warnings:
./drivers/net/wireless/mediatek/mt76/eeprom.c:58:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:61:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:67:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:70:2-8: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
./drivers/net/wireless/mediatek/mt76/eeprom.c:72:1-7: ERROR: missing of_node_put; acquired a node pointer with refcount incremented on line 48, but without a corresponding object release within this function.
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following types of blank line problems are reported:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The following problems were found:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
CHECK: Please use a blank line after function/struct/union/enum declarations
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The problems filed include the following:
WARNING: Missing a blank line after declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The types of problems fixed are as follows:
WARNING: Missing a blank line after declarations
CHECK: Please use a blank line after function/struct/union/enum declarations
CHECK: Please don't use multiple blank lines
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The errors consist of multiple blank lines, and a missing blank line
after the declarations.
There are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The instances where statement continuations are improperly aligned have
been fixed.
There are no changes to generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl reports a number of problems with block comments.
These changes do not affect the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Checkpatch.pl report problems in wifi.h where spaces are missing, as well
as extraneous spaces.
There are no changes in the generated code.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The call to ieee80211_probereq_get can return NULL if a skb allocation
fails, so add a null pointer check and free an earlier skb on the error
exit return path.
Fixes: 7fdcb8e126 ("rsi: add support for hardware scan offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If the card was removed in suspended state and a new one was inserted,
print a debug log when the check detects that it's not the old card.
Signed-off-by: hongjiefang <hongjiefang@asrmicro.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Firmware may report general errors using a special message type. Add
basic support for it by simply decoding & printing an error number.
A sample situation in which firmware reports a buf error:
CONSOLE: 027084.733 no host response IOCTL buffer available..so fail the request
will now produce a "Firmware reported general error: 9" on the host.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This updates host struct to match the in-firmawre definition. It's a
cosmetic change as it only applies to the reserved struct space.
Fixes: c988b78244 ("brcmfmac: print firmware reported ring status errors")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
SD spec v5.1 adds discard support. The flows and commands are similar to
mmc, so just set the discard arg in CMD38.
A host which supports DISCARD shall check if the DISCARD_SUPPORT (b313)
is set in the SD_STATUS register. If the card does not support discard,
the host shall not issue DISCARD command, but ERASE command instead.
Post the DISCARD operation, the card may de-allocate the discarded
blocks partially or completely. So the host mustn't make any assumptions
concerning the content of the discarded region. This is unlike ERASE
command, in which the region is guaranteed to contain either '0's or
'1's, depends on the content of DATA_STAT_AFTER_ERASE (b55) in the scr
register.
One more important difference compared to ERASE is the busy timeout
which we will address on the next patch.
Signed-off-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
the response type of CMD6 is R1B, when the first CMD6 gets response
CRC error, do retry may get timeout error due to card may still in
busy state, which cause this retry make no sense.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
perf annotate:
Wei Li:
- Fix getting source line failure
perf script:
Andi Kleen:
- Handle missing fields with -F +...
perf data:
Jiri Olsa:
- Prep work to support per-cpu files in a directory.
Intel PT:
Adrian Hunter:
- Improve thread_stack__no_call_return()
- Hide x86 retpolines in thread stacks.
- exported SQL viewer refactorings, new 'top calls' report..
Alexander Shishkin:
- Copy parent's address filter offsets on clone
- Fix address filters for vmas with non-zero offset. Applies to
ARM's CoreSight as well.
python scripts:
Tony Jones:
- Python3 support for several 'perf script' python scripts.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCXHRYNwAKCRCyPKLppCJ+
J8XmAQDKY7gb3GhkX+4aE8cGffFYB2YV5mD9Bbu4AM9tuFFBJwD+KAq87FMCy7m7
h7xyWk3UILpz6y235AVdfOmgcNDkpAQ=
=SJCG
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-5.1-20190225' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
perf annotate:
Wei Li:
- Fix getting source line failure
perf script:
Andi Kleen:
- Handle missing fields with -F +...
perf data:
Jiri Olsa:
- Prep work to support per-cpu files in a directory.
Intel PT:
Adrian Hunter:
- Improve thread_stack__no_call_return()
- Hide x86 retpolines in thread stacks.
- exported SQL viewer refactorings, new 'top calls' report..
Alexander Shishkin:
- Copy parent's address filter offsets on clone
- Fix address filters for vmas with non-zero offset. Applies to
ARM's CoreSight as well.
python scripts:
Tony Jones:
- Python3 support for several 'perf script' python scripts.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
perf report:
He Kuang:
- Don't shadow inlined symbol with different addr range.
perf script:
Jiri Olsa:
- Allow +- operator to ask for -F to add/remove fields to
the default set, for instance to ask for the removal of the
'cpu' field in tracepoint events, adding 'period' to that
kind of events, etc.
perf test:
Thomas Richter:
- Fix scheduler tracepoint signedness of COMM fields failure of
'evsel-tp-sched' test on s390 and other arches.
Tommi Rantala:
- Skip trace+probe_vfs_getname.sh when 'perf trace' is not built.
perf trace:
Arnaldo Carvalho de Melo:
- Add initial BPF map dumper, initially just for the current, minimal
needs of the augmented_raw_syscalls BPF example used to collect
pointer args payloads that uses BPF maps for pid and syscall filtering,
but will in time have features similar to 'perf stat' --interval-print,
--interval-clear, ways to signal from a BPF event that a specific
map (or range of that map) should be printed, optionally as a
histogram, etc.
General:
Jiri Olsa:
- Add cpu and numa topologies classes for further reuse, fixing some
issues in the process.
- Fixup some warnings and debug levels.
- Make rm_rf() remove single file, not just directories.
Documentation:
Jonas Rabenstein:
- Fix HEADER_CMDLINE description in perf.data documentation.
- Fix documentation of the Flags section in perf.data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQR2GiIUctdOfX2qHhGyPKLppCJ+JwUCXG36iwAKCRCyPKLppCJ+
J3+oAQDRx1tbb3PcenZ1ksgrK3FPyatZ4tM2VRkJpvaCNKk/SwEA9q6xkYNUK1BT
7ogDbIbnQO1Dz9jMsekoQu1+fd2ykAU=
=NcJY
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-5.1-20190220' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
perf report:
He Kuang:
- Don't shadow inlined symbol with different addr range.
perf script:
Jiri Olsa:
- Allow +- operator to ask for -F to add/remove fields to
the default set, for instance to ask for the removal of the
'cpu' field in tracepoint events, adding 'period' to that
kind of events, etc.
perf test:
Thomas Richter:
- Fix scheduler tracepoint signedness of COMM fields failure of
'evsel-tp-sched' test on s390 and other arches.
Tommi Rantala:
- Skip trace+probe_vfs_getname.sh when 'perf trace' is not built.
perf trace:
Arnaldo Carvalho de Melo:
- Add initial BPF map dumper, initially just for the current, minimal
needs of the augmented_raw_syscalls BPF example used to collect
pointer args payloads that uses BPF maps for pid and syscall filtering,
but will in time have features similar to 'perf stat' --interval-print,
--interval-clear, ways to signal from a BPF event that a specific
map (or range of that map) should be printed, optionally as a
histogram, etc.
General:
Jiri Olsa:
- Add CPU and NUMA topologies classes for further reuse, fixing some
issues in the process.
- Fixup some warnings and debug levels.
- Make rm_rf() remove single file, not just directories.
Documentation:
Jonas Rabenstein:
- Fix HEADER_CMDLINE description in perf.data documentation.
- Fix documentation of the Flags section in perf.data.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Shrink struct lock_class_key; we never store anything in subkeys[], we
only use the addresses.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
And move the whole lot under CONFIG_DEBUG_LOCKDEP.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will.deacon@arm.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Make sure that the lockdep_register_key() and lockdep_unregister_key()
code is tested when running the lockdep tests.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-24-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Apparently the execute bits were set for the tests/*.sh scripts on my
test setup but these are not set in the kernel tree. Fix this by adding
the interpreter path in front of the script paths.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Fixes: 5ecb8e94b4 ("tools/lib/lockdep/tests: Improve testing accuracy") # v5.0-rc1
Link: https://lkml.kernel.org/r/20190214230058.196511-23-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The following commit:
87915adc3f ("workqueue: re-add lockdep dependencies for flushing")
improved deadlock checking in the workqueue implementation. Unfortunately
that patch also introduced a few false positive lockdep complaints.
This patch suppresses these false positives by allocating the workqueue mutex
lockdep key dynamically.
An example of a false positive lockdep complaint suppressed by this patch
can be found below. The root cause of the lockdep complaint shown below
is that the direct I/O code can call alloc_workqueue() from inside a work
item created by another alloc_workqueue() call and that both workqueues
share the same lockdep key. This patch avoids that that lockdep complaint
is triggered by allocating the work queue lockdep keys dynamically.
In other words, this patch guarantees that a unique lockdep key is
associated with each work queue mutex.
======================================================
WARNING: possible circular locking dependency detected
4.19.0-dbg+ #1 Not tainted
fio/4129 is trying to acquire lock:
00000000a01cfe1a ((wq_completion)"dio/%s"sb->s_id){+.+.}, at: flush_workqueue+0xd0/0x970
but task is already holding lock:
00000000a0acecf9 (&sb->s_type->i_mutex_key#14){+.+.}, at: ext4_file_write_iter+0x154/0x710
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (&sb->s_type->i_mutex_key#14){+.+.}:
down_write+0x3d/0x80
__generic_file_fsync+0x77/0xf0
ext4_sync_file+0x3c9/0x780
vfs_fsync_range+0x66/0x100
dio_complete+0x2f5/0x360
dio_aio_complete_work+0x1c/0x20
process_one_work+0x481/0x9f0
worker_thread+0x63/0x5a0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
-> #1 ((work_completion)(&dio->complete_work)){+.+.}:
process_one_work+0x447/0x9f0
worker_thread+0x63/0x5a0
kthread+0x1cf/0x1f0
ret_from_fork+0x24/0x30
-> #0 ((wq_completion)"dio/%s"sb->s_id){+.+.}:
lock_acquire+0xc5/0x200
flush_workqueue+0xf3/0x970
drain_workqueue+0xec/0x220
destroy_workqueue+0x23/0x350
sb_init_dio_done_wq+0x6a/0x80
do_blockdev_direct_IO+0x1f33/0x4be0
__blockdev_direct_IO+0x79/0x86
ext4_direct_IO+0x5df/0xbb0
generic_file_direct_write+0x119/0x220
__generic_file_write_iter+0x131/0x2d0
ext4_file_write_iter+0x3fa/0x710
aio_write+0x235/0x330
io_submit_one+0x510/0xeb0
__x64_sys_io_submit+0x122/0x340
do_syscall_64+0x71/0x220
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Chain exists of:
(wq_completion)"dio/%s"sb->s_id --> (work_completion)(&dio->complete_work) --> &sb->s_type->i_mutex_key#14
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(&sb->s_type->i_mutex_key#14);
lock((work_completion)(&dio->complete_work));
lock(&sb->s_type->i_mutex_key#14);
lock((wq_completion)"dio/%s"sb->s_id);
*** DEADLOCK ***
1 lock held by fio/4129:
#0: 00000000a0acecf9 (&sb->s_type->i_mutex_key#14){+.+.}, at: ext4_file_write_iter+0x154/0x710
stack backtrace:
CPU: 3 PID: 4129 Comm: fio Not tainted 4.19.0-dbg+ #1
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1 04/01/2014
Call Trace:
dump_stack+0x86/0xc5
print_circular_bug.isra.32+0x20a/0x218
__lock_acquire+0x1c68/0x1cf0
lock_acquire+0xc5/0x200
flush_workqueue+0xf3/0x970
drain_workqueue+0xec/0x220
destroy_workqueue+0x23/0x350
sb_init_dio_done_wq+0x6a/0x80
do_blockdev_direct_IO+0x1f33/0x4be0
__blockdev_direct_IO+0x79/0x86
ext4_direct_IO+0x5df/0xbb0
generic_file_direct_write+0x119/0x220
__generic_file_write_iter+0x131/0x2d0
ext4_file_write_iter+0x3fa/0x710
aio_write+0x235/0x330
io_submit_one+0x510/0xeb0
__x64_sys_io_submit+0x122/0x340
do_syscall_64+0x71/0x220
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes.berg@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Tejun Heo <tj@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Link: https://lkml.kernel.org/r/20190214230058.196511-20-bvanassche@acm.org
[ Reworked the changelog a bit. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A shortcoming of the current lockdep implementation is that it requires
lock keys to be allocated statically. That forces all instances of lock
objects that occur in a given data structure to share a lock key. Since
lock dependency analysis groups lock objects per key sharing lock keys
can cause false positive lockdep reports. Make it possible to avoid
such false positive reports by allowing lock keys to be allocated
dynamically. Require that dynamically allocated lock keys are
registered before use by calling lockdep_register_key(). Complain about
attempts to register the same lock key pointer twice without calling
lockdep_unregister_key() between successive registration calls.
The purpose of the new lock_keys_hash[] data structure that keeps
track of all dynamic keys is twofold:
- Verify whether the lockdep_register_key() and lockdep_unregister_key()
functions are used correctly.
- Avoid that lockdep_init_map() complains when encountering a dynamically
allocated key.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-19-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Debugging lockdep data structure inconsistencies is challenging. Add
code that verifies data structure consistency at runtime. That code is
disabled by default because it is very CPU intensive.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-17-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A previous patch introduced a lock chain leak. Fix that leak by reusing
lock chains that have been freed.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-16-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Reflect that add_chain_cache() is always called with the graph lock held.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-15-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch does not change any functionality but makes the next patch in
this series easier to read.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-14-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Instead of abandoning elements of list_entries[] that are no longer in
use, make alloc_list_entry() reuse array elements that have been freed.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-13-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Instead of leaving lock classes that are no longer in use in the
lock_classes array, reuse entries from that array that are no longer in
use. Maintain a linked list of free lock classes with list head
'free_lock_class'. Only add freed lock classes to the free_lock_classes
list after a grace period to avoid that a lock_classes[] element would
be reused while an RCU reader is accessing it. Since the lockdep
selftests run in a context where sleeping is not allowed and since the
selftests require that lock resetting/zapping works with debug_locks
off, make the behavior of lockdep_free_key_range() and
lockdep_reset_lock() depend on whether or not these are called from
the context of the lockdep selftests.
Thanks to Peter for having shown how to modify get_pending_free()
such that that function does not have to sleep.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-12-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
synchronize_sched() has been removed recently. Update the comments that
refer to synchronize_sched().
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Fixes: 51959d85f3 ("lockdep: Replace synchronize_sched() with synchronize_rcu()") # v5.0-rc1
Link: https://lkml.kernel.org/r/20190214230058.196511-11-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The patch that frees unused lock classes will modify the behavior of
lockdep_free_key_range() and lockdep_reset_lock() depending on whether
or not these functions are called from the context of the lockdep
selftests. Hence make it easy to detect whether or not lockdep code
is called from the context of a lockdep selftest.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-10-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch does not change the behavior of these functions but makes the
patch that frees unused lock classes easier to read.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-9-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch does not change any functionality. A later patch will reuse
lock classes that have been freed. In combination with that patch this
patch wil have the effect of initializing lock class order lists once
instead of every time a lock class structure is reinitialized.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Johannes Berg <johannes@sipsolutions.net>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Waiman Long <longman@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: johannes.berg@intel.com
Cc: tj@kernel.org
Link: https://lkml.kernel.org/r/20190214230058.196511-8-bvanassche@acm.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>