Pull tile update from Chris Metcalf:
"The interesting bug fix is support for the upcoming "4.2" release of
the Tilera hypervisor, which by default launches Linux at privilege
level 2 instead of 1. The fix lets new and old hypervisors and
Linuxes interoperate more smoothly, so I've tagged it for
stable@kernel.org so that older Linuxes will be able to boot under the
newer hypervisor."
* 'stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
usb: tilegx: fix memleak when create hcd fail
arch/tile: remove inline marking of EXPORT_SYMBOL functions
rtc: rtc-tile: add missing platform_device_unregister() when module exit
tile: support new Tilera hypervisor
Pull networking update from David Miller:
1) Propagate return error values properly in irda, spider_net, sfc, and
bfin_mac. From Wei Yongjun.
2) Fix fec driver OOPS on rapid link up/down, from Frank Li.
3) FIX VF resource allocation and chip message payload length errors in
be2net driver, from Sathya Perla.
4) Fix inner protocol inspection during GSO from Pravin B Shelar.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net:
if_cablemodem.h: Add parenthesis around ioctl macros
gso: Handle Trans-Ether-Bridging protocol in skb_network_protocol()
net: fec: fix kernel oops when plug/unplug cable many times
bfin_mac: fix error return code in bfin_mac_probe()
sfc: fix return value check in efx_ptp_probe_channel()
net/spider_net: fix error return code in spider_net_open()
net/irda: fix error return code in bfin_sir_open()
net: of_mdio: fix behavior on missing phy device
sierra_net: keep status interrupt URB active
usbnet: allow status interrupt URB to always be active
qmi_wwan/cdc_ether: add device IDs for Dell 5804 (Novatel E371) WWAN card
be2net: disable TX in be_close()
be2net: fix EQ from getting full while cleaning RX CQ
be2net: fix payload_len value for GET_MAC_LIST cmd req
be2net: provision VF resources before enabling SR-IOV
GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any valid
cases for enableing GENERIC_GPIO without GPIOLIB, even though it is
possible to do so which has been causing confusion and breakage. This
branch does the work to completely eliminate GENERIC_GPIO.
However, it is not trivial to just create a branch to remove it. Over
the course of the v3.9 cycle more code referencing GENERIC_GPIO has been
added to linux-next that conflicts with this branch. The following must
be done to resolve the conflicts when merging this branch into mainline:
* "git grep CONFIG_GENERIC_GPIO" should return 0 hits. Matches should be
replaced with CONFIG_GPIOLIB
* "git grep '\bGENERIC_GPIO\b'" should return 1 hit in the Chinese
documentation.
* Selectors of GENERIC_GPIO should be turned into selectors of GPIOLIB
* definitions of the option in architecture Kconfig code should be deleted.
Stephen has 3 merge fixup patches[1] that do the above. They are currently
applicable on mainline as of May 2nd.
[1] http://www.mail-archive.com/linux-kernel@vger.kernel.org/msg428056.html
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xodc
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux
Pull removal of GENERIC_GPIO from Grant Likely:
"GENERIC_GPIO now synonymous with GPIOLIB. There are no longer any
valid cases for enableing GENERIC_GPIO without GPIOLIB, even though it
is possible to do so which has been causing confusion and breakage.
This branch does the work to completely eliminate GENERIC_GPIO."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux:
gpio: update gpio Chinese documentation
Remove GENERIC_GPIO config option
Convert selectors of GENERIC_GPIO to GPIOLIB
blackfin: force use of gpiolib
m68k: coldfire: use gpiolib
mips: pnx833x: remove requirement for GENERIC_GPIO
openrisc: default GENERIC_GPIO to false
avr32: default GENERIC_GPIO to false
xtensa: remove explicit selection of GENERIC_GPIO
sh: replace CONFIG_GENERIC_GPIO by CONFIG_GPIOLIB
powerpc: remove redundant GENERIC_GPIO selection
unicore32: default GENERIC_GPIO to false
unicore32: remove unneeded select GENERIC_GPIO
arm: plat-orion: use GPIO driver on CONFIG_GPIOLIB
arm: remove redundant GENERIC_GPIO selection
mips: alchemy: require gpiolib
mips: txx9: change GENERIC_GPIO to GPIOLIB
mips: loongson: use GPIO driver on CONFIG_GPIOLIB
mips: remove redundant GENERIC_GPIO select
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1ojD
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull InfiniBand/RDMA changes from Roland Dreier:
- XRC transport fixes
- Fix DHCP on IPoIB
- mlx4 preparations for flow steering
- iSER fixes
- miscellaneous other fixes
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (23 commits)
IB/iser: Add support for iser CM REQ additional info
IB/iser: Return error to upper layers on EAGAIN registration failures
IB/iser: Move informational messages from error to info level
IB/iser: Add module version
mlx4_core: Expose a few helpers to fill DMFS HW strucutures
mlx4_core: Directly expose fields of DMFS HW rule control segment
mlx4_core: Change a few DMFS fields names to match firmare spec
mlx4: Match DMFS promiscuous field names to firmware spec
mlx4_core: Move DMFS HW structs to common header file
IB/mlx4: Set link type for RAW PACKET QPs in the QP context
IB/mlx4: Disable VLAN stripping for RAW PACKET QPs
mlx4_core: Reduce warning message for SRQ_LIMIT event to debug level
RDMA/iwcm: Don't touch cmid after dropping reference
IB/qib: Correct qib_verbs_register_sysfs() error handling
IB/ipath: Correct ipath_verbs_register_sysfs() error handling
RDMA/cxgb4: Fix SQ allocation when on-chip SQ is disabled
SRPT: Fix odd use of WARN_ON()
IPoIB: Fix ipoib_hard_header() return value
RDMA: Rename random32() to prandom_u32()
RDMA/cxgb3: Fix uninitialized variable
...
reproduce steps
1. flood ping from other machine
ping -f -s 41000 IP
2. run below script
while [ 1 ]; do ethtool -s eth0 autoneg off;
sleep 3;ethtool -s eth0 autoneg on; sleep 4; done;
You can see oops in one hour.
The reason is fec_restart clear BD but NAPI may use it.
The solution is disable NAPI and stop xmit when reset BD.
disable NAPI may sleep, so fec_restart can't be call in
atomic context.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
Tested-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
In case of error, the function ptp_clock_register() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Reviewed-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return a negative error code from the error handling
case instead of 0, as done elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix to return -ENOMEM in the irlap_open() error handling case instead
of 0(overwrite to 0 by bfin_sir_startup()), as done elsewhere in this
function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver and firmware sync up through SYNC messages, and the
firmware's affirmative reply to these SYNC messages appears to be the
"Reset" indication received via the status interrupt endpoint. Thus the
driver needs the status interrupt endpoint always active so that the
Reset indication can be received even if the netdev is closed, which is
the case right after device insertion.
If the Reset indication is not received by the driver, it continues
sending SYNC messages to the firmware, which crashes about 10 seconds
later and the device stops responding.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some drivers (sierra_net) need the status interrupt URB
active even when the device is closed, because they receive
custom indications from firmware. Add functions to refcount
the status interrupt URB submit/kill operation so that
sub-drivers and the generic driver don't fight over whether
the status interrupt URB is active or not.
A sub-driver can call usbnet_status_start() at any time, but
the URB is only submitted the first time the function is
called. Likewise, when the sub-driver is done with the URB,
it calls usbnet_status_stop() but the URB is only killed when
all users have stopped it. The URB is still killed and
re-submitted for suspend/resume, as before, with the same
refcount it had at suspend.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Oliver Neukum <oliver@neukum.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A rebranded Novatel E371 for AT&T's LTE bands. qmi_wwan should drive this
device, while cdc_ether should ignore it. Even though the USB descriptors
are plain CDC-ETHER that USB interface is a QMI interface.
Cc: <stable@vger.kernel.org>
Signed-off-by: Dan Williams <dcbw@redhat.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
be_close() followed by be_clear() is called as a part of cleanup in the
EEH/AER flow. This patch stops TX in be_close() before cleaning/freeing
up the TX queues in be_clear(). This prevents be_xmit() from being called
while TX queues no longer exist.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While cleaning RX queues, the CQ DB may be rung several times (with rearm)
while waiting for the flush compl. Each CQ-notify with rearm can result in
an event. The EQ may get full resulting in a HW error.
Fix this by not re-arming the CQ while notifying a valid completion.
Also, there's no need to wait for 1ms after destroying RXQ, as the code in
be_rx_cq_clean() waits for the flush compl to arrive.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The buffer size for a FW cmd request must be big enough to fit the response,
else the cmd fails. For GET_MAC_LIST cmd, though the memory allocated for
the cmd is big enough to fit the response, the payload_len value in the
WRB hdr is being set to the request length only.
Fix this for GET_MAC_LIST cmd.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the PF driver calls pci_enable_sriov(), the VFs may be probed
inline before the call returns. So, the resources required for all VFs
must be provisioned by the PF driver *before* calling pci_enable_sriov();
else, VF probe will fail.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Merge more incoming from Andrew Morton:
- Various fixes which were stalled or which I picked up recently
- A large rotorooting of the AIO code. Allegedly to improve
performance but I don't really have good performance numbers (I might
have lost the email) and I can't raise Kent today. I held this out
of 3.9 and we could give it another cycle if it's all too late/scary.
I ended up taking only the first two thirds of the AIO rotorooting. I
left the percpu parts and the batch completion for later. - Linus
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (33 commits)
aio: don't include aio.h in sched.h
aio: kill ki_retry
aio: kill ki_key
aio: give shared kioctx fields their own cachelines
aio: kill struct aio_ring_info
aio: kill batch allocation
aio: change reqs_active to include unreaped completions
aio: use cancellation list lazily
aio: use flush_dcache_page()
aio: make aio_read_evt() more efficient, convert to hrtimers
wait: add wait_event_hrtimeout()
aio: refcounting cleanup
aio: make aio_put_req() lockless
aio: do fget() after aio_get_req()
aio: dprintk() -> pr_debug()
aio: move private stuff out of aio.h
aio: add kiocb_cancel()
aio: kill return value of aio_complete()
char: add aio_{read,write} to /dev/{null,zero}
aio: remove retry-based AIO
...
These are mostly new device tree bindings for existing drivers, as well
as changes to the device tree source files to add support for those
devices, and a couple of new boards, most notably Samsung's Exynos5
based Chromebook.
The changes depend on earlier platform specific updates and touch
the usual platforms: omap, exynos, tegra, mxs, mvebu and davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G60S
-----END PGP SIGNATURE-----
Merge tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC device tree updates (part 2) from Arnd Bergmann:
"These are mostly new device tree bindings for existing drivers, as
well as changes to the device tree source files to add support for
those devices, and a couple of new boards, most notably Samsung's
Exynos5 based Chromebook.
The changes depend on earlier platform specific updates and touch the
usual platforms: omap, exynos, tegra, mxs, mvebu and davinci."
* tag 'dt-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (169 commits)
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: add mshc controller node for Exynos4x12 SoCs
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
ARM: davinci: da850-evm: add SPI flash support
ARM: davinci: da850: override SPI DT node device name
ARM: davinci: da850: add SPI1 DT node
spi/davinci: add DT binding documentation
spi/davinci: no wildcards in DT compatible property
ARM: dts: mvebu: Convert mvebu device tree files to 64 bits
ARM: dts: mvebu: introduce internal-regs node
ARM: dts: mvebu: Convert all the mvebu files to use the range property
ARM: dts: mvebu: move all peripherals inside soc
ARM: dts: mvebu: fix cpus section indentation
ARM: davinci: da850: add EHRPWM & ECAP DT node
ARM/dts: OMAP3: fix pinctrl-single configuration
ARM: dts: Add OMAP3430 SDP NOR flash memory binding
ARM: dts: Add NOR flash bindings for OMAP2420 H4
...
A scheduling while atomic bug was introduced recently (by commit
ce43a2168c59: "e1000e: cleanup USLEEP_RANGE checkpatch checks").
Revert the particular instance of usleep_range() which causes the bug.
Reported-by: Maarten Lankhorst <m.b.lankhorst@gmail.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is support for the ARM Chromebook, originally scheduled
as a "late" pull request. Since it's already late now, we
can combine this into the existing next/dt2 branch.
* late/dt:
ARM: exynos: dts: cros5250: add EC device
ARM: dts: Add sbs-battery for exynos5250-snow
ARM: dts: Add i2c-arbitrator bus for exynos5250-snow
ARM: dts: Add chip-id controller node on Exynos4/5 SoC
ARM: EXYNOS: Create virtual I/O mapping for Chip-ID controller using device tree
Add new driver for supporting Realtek RTL8152 Based USB 2.0 Ethernet Adapters
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Cc: Realtek linux nic maintainers <nic_swsd@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When unloading the driver that drives an EISA board, a message similar to the
following one is displayed:
Trying to free nonexistent resource <0000000000013000-000000000001301f>
Then an user is unable to reload the driver because the resource it requested in
the previous load hasn't been freed. This happens most probably due to a typo in
vortex_eisa_remove() which calls release_region() with 'dev->base_addr' instead
of 'edev->base_addr'...
Reported-by: Matthew Whitehead <tedheadster@gmail.com>
Tested-by: Matthew Whitehead <tedheadster@gmail.com>
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some ancient pHyp versions used to create a 8 bytes local-mac-address
property in the device-tree instead of a 6 bytes one for veth.
The Linux driver code to deal with that is an insane hack which also
happens to break with some choices of MAC addresses in qemu by testing
for a bit in the address rather than just looking at the size of the
property.
Sanitize this by doing the latter instead.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull single_open() leak fixes from Al Viro:
"A bunch of fixes for a moderately common class of bugs: file with
single_open() done by its ->open() and seq_release as its ->release().
That leaks; fortunately, it's not _too_ common (either people manage
to RTFM that says "When using single_open(), the programmer should use
single_release() instead of seq_release() in the file_operations
structure to avoid a memory leak", or they just copy a correct
instance), but grepping through the tree has caught quite a pile.
All of that is, AFAICS, -stable fodder, for as far as the patches
apply. I tried to carve it up into reasonably-sized pieces (more or
less "comes from the same tree")"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
rcutrace: single_open() leaks
gadget: single_open() leaks
staging: single_open() leaks
megaraid: single_open() leak
wireless: single_open() leaks
input: single_open() leak
rtc: single_open() leaks
ds1620: single_open() leak
sh: single_open() leaks
parisc: single_open() leaks
mips: single_open() leaks
ia64: single_open() leaks
h8300: single_open() leaks
cris: single_open() leaks
arm: single_open() leaks
Pull networking fixes from David Miller:
1) Several routines do not use netdev_features_t to hold such bitmasks,
fixes from Patrick McHardy and Bjørn Mork.
2) Update cpsw IRQ software state and the actual HW irq enabling in the
correct order. From Mugunthan V N.
3) When sending tipc packets to multiple bearers, we have to make
copies of the SKB rather than just giving the original SKB directly.
Fix from Gerlando Falauto.
4) Fix race with bridging topology change timer, from Stephen
Hemminger.
5) Fix TCPv6 segmentation handling in GRE and VXLAN, from Pravin B
Shelar.
6) Endian bug in USB pegasus driver, from Dan Carpenter.
7) Fix crashes on MTU reduction in USB asix driver, from Holger
Eitzenberger.
8) Don't allow the kernel to BUG() just because the user puts some crap
in an AF_PACKET mmap() ring descriptor. Fix from Daniel Borkmann.
9) Don't use variable sized arrays on the stack in xen-netback, from
Wei Liu.
10) Fix stats reporting and an unbalanced napi_disable() in be2net
driver. From Somnath Kotur and Ajit Khaparde.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (25 commits)
cxgb4: fix error recovery when t4_fw_hello returns a positive value
sky2: Fix crash on receiving VLAN frames
packet: tpacket_v3: do not trigger bug() on wrong header status
asix: fix BUG in receive path when lowering MTU
net: qmi_wwan: Add Telewell TW-LTE 4G
usbnet: pegasus: endian bug in write_mii_word()
vxlan: Fix TCPv6 segmentation.
gre: Fix GREv4 TCPv6 segmentation.
bridge: fix race with topology change timer
tipc: pskb_copy() buffers when sending on more than one bearer
tipc: tipc_bcbearer_send(): simplify bearer selection
tipc: cosmetic: clean up comments and break a long line
drivers: net: cpsw: irq not disabled in cpsw isr in particular sequence
xen-netback: better names for thresholds
xen-netback: avoid allocating variable size array on stack
xen-netback: remove redundent parameter in netbk_count_requests
be2net: Fix to fail probe if MSI-X enable fails for a VF
be2net: avoid napi_disable() when it has not been enabled
be2net: Fix firmware download for Lancer
be2net: Fix to receive Multicast Packets when Promiscuous mode is enabled on certain devices
...
Since commit 636f9d371f ("cxgb4: Add
support for T4 configuration file"), t4_fw_hello may return a positive
value instead of 0 for success. The recovery code tests only for zero
and fails recovery for any other value.
This fix tests for negative error values and fails only on those cases.
Error recovery after an error injection works after this change.
Signed-off-by: Thadeu Lima de Souza Cascardo <cascardo@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After recent 86a9bad3 (net: vlan: add protocol argument to packet
tagging functions) my sky2 started to crash on receive of tagged
frames, with backtrace similar to
#CRASH!!!
vlan_do_receive
__netif_receive_skb_core
__netif_receive_skb
netif_receive_skb
sky2_poll
...
__net_rx_action
__do_softirq
The problem turned out to be:
1) sky2 copies small packets from ring on RX, and in its
receive_copy() skb header is copied manually field, by field, and
only for some fields;
2) 86a9bad3 added skb->vlan_proto, which vlan_untag() or
__vlan_hwaccel_put_tag() set, and which is later used in
vlan_do_receive().
That patch updated copy_skb_header() for newly introduced
skb->vlan_proto, but overlooked the need to also copy it in sky2's
receive_copy().
Because of 2, we have the following scenario:
- frame is received and tagged in a ring, by sky2_rx_tag(). Both
skb->vlan_proto and skb->vlan_tci are set;
- later skb is decided to be copied, but skb->vlan_proto is
forgotten and becomes 0.
- in the beginning of vlan_do_receive() we call
__be16 vlan_proto = skb->vlan_proto;
vlan_dev = vlan_find_dev(skb->dev, vlan_proto, vlan_id);
which eventually invokes
vlan_proto_idx(vlan_proto)
and that routine BUGs for everything except ETH_P_8021Q and
ETH_P_8021AD.
Oops.
Fix it.
P.S.
Stephen, I wonder, why copy_skb_header() is not used in
sky2.c::receive_copy() ? Problems, where receive_copy was updated field
by field showed several times already, e.g.
3f42941b (sky2: propogate rx hash when packet is copied)
e072b3fa (sky2: fix receive length error in mixed non-VLAN/VLAN traffic)
Cc: Patrick McHardy <kaber@trash.net>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: Mirko Lindner <mlindner@marvell.com>
Signed-off-by: Kirill Smelkov <kirr@mns.spb.ru>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is bug in the receive path of the asix driver at the time a
packet is received larger than MTU size and DF bit set:
BUG: unable to handle kernel paging request at 0000004000000001
IP: [<ffffffff8126f65b>] skb_release_head_state+0x2d/0xd2
...
Call Trace:
<IRQ>
[<ffffffff8126f86d>] ? skb_release_all+0x9/0x1e
[<ffffffff8126f8ad>] ? __kfree_skb+0x9/0x6f
[<ffffffffa00b4200>] ? asix_rx_fixup_internal+0xff/0x1ae [asix]
[<ffffffffa00fb3dc>] ? usbnet_bh+0x4f/0x226 [usbnet]
...
It is easily reproducable by setting an MTU of 512 e. g. and sending
something like
ping -s 1472 -c 1 -M do $SELF
from another box.
And this is because the rx->ax_skb is freed on error, but rx->ax_skb
is not reset, and the size is not reset to zero in this case.
And since the skb is added again to the usbnet->done skb queue it is
accessing already freed memory, resulting in the BUG when freeing a
2nd time. I therefore think the value 0x0000004000000001 show in the
trace is more or less random data.
Signed-off-by: Holger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We're only passing the two high bytes of an integer. It works for
little endian but not for big endian.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull i2c changes from Wolfram Sang:
- an arbitration driver. While the driver is quite simple, it caused
discussion if we need additional arbitration on top of the one
specified in the I2C standard. Conclusion is that I accept a few
generic mechanisms, but not very specific ones.
- the core lost the detach_adapter() call. It has no users anymore and
was in the way for other cleanups. attach_adapter() is sadly still
there since there are users waiting to be converted.
- the core gained a bus recovery infrastructure. I2C defines a way to
recover if the data line is stalled. This mechanism is now in the
core and drivers can now pass some data to make use of it.
- bigger driver cleanups for designware, s3c2410
- removing superfluous refcounting from drivers
- removing Ben Dooks as second maintainer due to inactivity. Thanks
for all your work so far, Ben!
- bugfixes, feature additions, devicetree fixups, simplifications...
* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (38 commits)
i2c: xiic: must always write 16-bit words to TX_FIFO
i2c: octeon: use HZ in timeout value
i2c: octeon: Fix i2c fail problem when a process is terminated by a signal
i2c: designware-pci: drop superfluous {get|put}_device
i2c: designware-plat: drop superfluous {get|put}_device
i2c: davinci: drop superfluous {get|put}_device
MAINTAINERS: Ben Dooks is inactive regarding I2C
i2c: mux: Add i2c-arb-gpio-challenge 'mux' driver
i2c: at91: convert to dma_request_slave_channel_compat()
i2c: mxs: do error checking and handling in PIO mode
i2c: mxs: remove races in PIO code
i2c-designware: switch to use runtime PM autosuspend
i2c-designware: use usleep_range() in the busy-loop
i2c-designware: enable/disable the controller properly
i2c-designware: use dynamic adapter numbering on Lynxpoint
i2c-designware-pci: use managed functions pcim_* and devm_*
i2c-designware-pci: use dev_err() instead of printk()
i2c-designware: move to managed functions (devm_*)
i2c: remove CONFIG_HOTPLUG ifdefs
i2c: s3c2410: Add SMBus emulation for block read
...
I dived into lguest again, reworking the pagetable code so we can move
the switcher page: our fixmaps sometimes take more than 2MB now...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=1tYL
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio & lguest updates from Rusty Russell:
"Lots of virtio work which wasn't quite ready for last merge window.
Plus I dived into lguest again, reworking the pagetable code so we can
move the switcher page: our fixmaps sometimes take more than 2MB now..."
Ugh. Annoying conflicts with the tcm_vhost -> vhost_scsi rename.
Hopefully correctly resolved.
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux: (57 commits)
caif_virtio: Remove bouncing email addresses
lguest: improve code readability in lg_cpu_start.
virtio-net: fill only rx queues which are being used
lguest: map Switcher below fixmap.
lguest: cache last cpu we ran on.
lguest: map Switcher text whenever we allocate a new pagetable.
lguest: don't share Switcher PTE pages between guests.
lguest: expost switcher_pages array (as lg_switcher_pages).
lguest: extract shadow PTE walking / allocating.
lguest: make check_gpte et. al return bool.
lguest: assume Switcher text is a single page.
lguest: rename switcher_page to switcher_pages.
lguest: remove RESERVE_MEM constant.
lguest: check vaddr not pgd for Switcher protection.
lguest: prepare to make SWITCHER_ADDR a variable.
virtio: console: replace EMFILE with EBUSY for already-open port
virtio-scsi: reset virtqueue affinity when doing cpu hotplug
virtio-scsi: introduce multiqueue support
virtio-scsi: push vq lock/unlock into virtscsi_vq_done
virtio-scsi: pass struct virtio_scsi to virtqueue completion function
...
In CPSW NAPI, after processing all interrupts IRQ is enabled and then book
keeping irq_enabled is updated. In random cases when a packet is transmitted
or received between processing packets and IRQ enabled, then just after
enabled IRQ and before irq_enabled is updated, ISR is called so IRQs are
not disabled as irq_enabled is still false and CPU gets locked in CPSW ISR.
By changing the sequence as update the irq_enabled and then enable IRQ
fixes the issue. This issue is not captured always as it is a timing issue
whether Tx or Rx IRQ is invoked between packet processing and enable IRQ.
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch only changes some names to avoid confusion.
In this patch we have:
MAX_SKB_SLOTS_DEFAULT -> FATAL_SKB_SLOTS_DEFAULT
max_skb_slots -> fatal_skb_slots
#define XEN_NETBK_LEGACY_SLOTS_MAX XEN_NETIF_NR_SLOTS_MIN
The fatal_skb_slots is the threshold to determine whether a packet is
malicious.
XEN_NETBK_LEGACY_SLOTS_MAX is the maximum slots a valid packet can have at
this point. It is defined to be XEN_NETIF_NR_SLOTS_MIN because that's
guaranteed to be supported by all backends.
Suggested-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tune xen_netbk_count_requests to not touch working array beyond limit, so that
we can make working array size constant.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tracking down from the caller, first_idx is always equal to vif->tx.req_cons.
Remove it to avoid confusion.
Suggested-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Wei Liu <wei.liu2@citrix.com>
Acked-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As per SPEC, INTx mode is not supported on VFs. So if enable_msix fails,
then just fail probe. Also bail out of be_open if irq_register fails.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When RQ creation fails in be_open(), driver jumps to be_close() where
napi_disable() is done without a prior napi_enable(); leading to a hang.
This change is needed as there is no way to see if napi is enable/disabled.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Increasing the timeout value of write_object command to 60 seconds as
30 second timeout was found to be not enough for the command to complete.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a user requests Promiscuous mode on SkyHawk-R devices,
the FW enables Desparate Promiscuous mode.
Due to this, we need to explicitly enable Multicast Promiscuous mode
so that Multicast packets are received as well.
This patch fixes that.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tx priority pause count is available with the driver.
But we were not showing it.
This change should fix it and display it in ethtool stats.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only BE devices provide 16-bit counter for rx_drops_no_fragment.
All other devices provide a 32-bit counter for this stat.
Use the 32-bit value where available.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SkyHawk-R devices should use v2 of cq_create command.
BE3/BE2 devices can use version 0 of the command to create a CQ.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Tilera hypervisor shipped in releases up through MDE 4.1 launches
the client operating system (i.e. Linux) at privilege level 1 (PL1).
Starting with MDE 4.2, as part of the work to enable KVM, the
Tilera hypervisor launches Linux at PL2 instead.
This commit makes the KERNEL_PL option default to 2 for tilegx, while
still saying at 1 for tilepro, which doesn't have an updated hypervisor.
It also explains how and when you might want to choose another value.
In addition, we change a small buglet in the on-chip Ethernet driver,
where we were failing to use the KERNEL_PL constant in an API call.
To make the transition cleaner, this change also provides the updated
hv_init() API for the new hypervisor that supports announcing Linux's
compiled-in PL, so the hypervisor can generate a suitable error in the
case of a mismatched hypervisor and Linux binary.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Cc: stable@vger.linux.org
Here is a collection of fixes (and some intermixed cleanups) that were
considered less important and thus not included in the later parts of
the 3.9-rc cycle.
It's a bit all over the map, contents wise. A series of ux500 fixes
and cleanups, a bunch of various fixes for OMAP and tegra, and some for
Freescale i.MX and even Qualcomm MSM.
Note that there's also a patch on this branch to globally turn off
-Wmaybe-uninitialized when building with -Os. It's been posted several
times by Arnd and no dissent was raised, but nobody seemed interested
to pick it up. So here it is, as the topmost patch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bzsu
-----END PGP SIGNATURE-----
Merge tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC non-critical fixes from Olof Johansson:
"Here is a collection of fixes (and some intermixed cleanups) that were
considered less important and thus not included in the later parts of
the 3.9-rc cycle.
It's a bit all over the map, contents wise. A series of ux500 fixes
and cleanups, a bunch of various fixes for OMAP and tegra, and some
for Freescale i.MX and even Qualcomm MSM.
Note that there's also a patch on this branch to globally turn off
-Wmaybe-uninitialized when building with -Os. It's been posted
several times by Arnd and no dissent was raised, but nobody seemed
interested to pick it up. So here it is, as the topmost patch."
* tag 'fixes-nc-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (70 commits)
Turn off -Wmaybe-uninitialized when building with -Os
ARM: orion5x: include linux/cpu.h
ARM: tegra: call cpu_do_idle from C code
ARM: u300: fix ages old copy/paste bug
ARM: OMAP2+: add dependencies on ARCH_MULTI_V6/V7
ARM: tegra: solve adr range issue with THUMB2_KERNEL enabled
ARM: tegra: fix relocation truncated error when THUMB2_KERNEL enabled
ARM: tegra: fix build error when THUMB2_KERNEL enabled
ARM: msm: Fix uncompess.h tx underrun check
ARM: vexpress: Remove A9 PMU compatible values for non-A9 platforms
ARM: cpuimx27 and mbimx27: prepend CONFIG_ to Kconfig macro
ARM: OMAP2+: fix typo "CONFIG_BRIDGE_DVFS"
ARM: OMAP1: remove "config MACH_OMAP_HTCWIZARD"
ARM: mach-imx: mach-imx6q: Fix sparse warnings
ARM: mach-imx: src: Include "common.h
ARM: mach-imx: gpc: Include "common.h"
ARM: mach-imx: avic: Staticize *avic_base
ARM: mach-imx: tzic: Staticize *tzic_base
ARM: mach-imx: clk: Include "clk.h"
ARM: mach-imx: clk-busy: Staticize clk_busy_mux_ops
...
Pull VFS updates from Al Viro,
Misc cleanups all over the place, mainly wrt /proc interfaces (switch
create_proc_entry to proc_create(), get rid of the deprecated
create_proc_read_entry() in favor of using proc_create_data() and
seq_file etc).
7kloc removed.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (204 commits)
don't bother with deferred freeing of fdtables
proc: Move non-public stuff from linux/proc_fs.h to fs/proc/internal.h
proc: Make the PROC_I() and PDE() macros internal to procfs
proc: Supply a function to remove a proc entry by PDE
take cgroup_open() and cpuset_open() to fs/proc/base.c
ppc: Clean up scanlog
ppc: Clean up rtas_flash driver somewhat
hostap: proc: Use remove_proc_subtree()
drm: proc: Use remove_proc_subtree()
drm: proc: Use minor->index to label things, not PDE->name
drm: Constify drm_proc_list[]
zoran: Don't print proc_dir_entry data in debug
reiserfs: Don't access the proc_dir_entry in r_open(), r_start() r_show()
proc: Supply an accessor for getting the data from a PDE's parent
airo: Use remove_proc_subtree()
rtl8192u: Don't need to save device proc dir PDE
rtl8187se: Use a dir under /proc/net/r8180/
proc: Add proc_mkdir_data()
proc: Move some bits from linux/proc_fs.h to linux/{of.h,signal.h,tty.h}
proc: Move PDE_NET() to fs/proc/proc_net.c
...
Use remove_proc_subtree() rather than remove_proc_entry() to remove a
device-specific proc directory and all its children.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Jouni Malinen <j@w1.fi>
cc: Johannes Berg <johannes@sipsolutions.net>
cc: linux-wireless@vger.kernel.org
cc: devel@driverdev.osuosl.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Use remove_proc_subtree() to remove the airo device subdir and all its
children instead of doing it manually.
Signed-off-by: David Howells <dhowells@redhat.com>
cc: linux-wireless@vger.kernel.org
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Linus Torvalds