Use DEFINE_DEBUGFS_ATTRIBUTE rather than DEFINE_SIMPLE_ATTRIBUTE
for debugfs files.
Semantic patch information:
Rationale: DEFINE_SIMPLE_ATTRIBUTE + debugfs_create_file()
imposes some significant overhead as compared to
DEFINE_DEBUGFS_ATTRIBUTE + debugfs_create_file_unsafe().
Generated by: scripts/coccinelle/api/debugfs/debugfs_simple_attr.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to add debugfs support for ptp_qoriq. Current debugfs
supports to control fiper1/fiper2 loopback mode. If the loopback mode
is enabled, the fiper1/fiper2 pulse is looped back into trigger1/
trigger2 input. This is very useful for validating hardware and driver
without external hardware. Below is an example to enable fiper1 loopback.
echo 1 > /sys/kernel/debug/2d10e00.ptp_clock/fiper1-loopback
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The external trigger stamp FIFO was introduced as a new feature
for QorIQ 1588 timer IP block. This patch is to support it by
adding a new dts property "fsl,extts-fifo". Any QorIQ 1588 timer
supporting this feature is required to add this property in its
dts node.
In addition, the FIFO should be cleaned up before enabling external
trigger interrupts. Otherwise, there will be interrupts immediately
just after enabling external trigger interrupts.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tmr_tevent register would update event bits
no matter tmr_temask bits were set or not. So we
should get interrupts by tmr_tevent & tmr_temask,
and clean up interrupts in tmr_tevent before
enabling them.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Otherwise it is impossible to use it for something else, as it will break
userspace that puts garbage there.
The same check should be done in other structures, but the fact that
data in reserved fields is ignored is already part of the kernel ABI.
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems to
be the "collection of various driver subsystems not big enough to have
their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems. This was discussed at the
Plumbers conference a few months ago and knocked into mergable shape
very fast by Christian Brauner. Who also has signed up to be
another binder maintainer, showing a distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXCZCUA8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymF9QCgx/Z8Fj1qzGVGrIE4flXOi7pxOrgAoMqJEWtU
ywwL8M9suKDz7cZT9fWQ
=xxr6
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of char and misc driver patches for 4.21-rc1.
Lots of different types of driver things in here, as this tree seems
to be the "collection of various driver subsystems not big enough to
have their own git tree" lately.
Anyway, some highlights of the changes in here:
- binderfs: is it a rule that all driver subsystems will eventually
grow to have their own filesystem? Binder now has one to handle the
use of it in containerized systems.
This was discussed at the Plumbers conference a few months ago and
knocked into mergable shape very fast by Christian Brauner. Who
also has signed up to be another binder maintainer, showing a
distinct lack of good judgement :)
- binder updates and fixes
- mei driver updates
- fpga driver updates and additions
- thunderbolt driver updates
- soundwire driver updates
- extcon driver updates
- nvmem driver updates
- hyper-v driver updates
- coresight driver updates
- pvpanic driver additions and reworking for more device support
- lp driver updates. Yes really, it's _finally_ moved to the proper
parallal port driver model, something I never thought I would see
happen. Good stuff.
- other tiny driver updates and fixes.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.21-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (116 commits)
MAINTAINERS: add another Android binder maintainer
intel_th: msu: Fix an off-by-one in attribute store
stm class: Add a reference to the SyS-T document
stm class: Fix a module refcount leak in policy creation error path
char: lp: use new parport device model
char: lp: properly count the lp devices
char: lp: use first unused lp number while registering
char: lp: detach the device when parallel port is removed
char: lp: introduce list to save port number
bus: qcom: remove duplicated include from qcom-ebi2.c
VMCI: Use memdup_user() rather than duplicating its implementation
char/rtc: Use of_node_name_eq for node name comparisons
misc: mic: fix a DMA pool free failure
ptp: fix an IS_ERR() vs NULL check
genwqe: Fix size check
binder: implement binderfs
binder: fix use-after-free due to ksys_close() during fdget()
bus: fsl-mc: remove duplicated include files
bus: fsl-mc: explicitly define the fsl_mc_command endianness
misc: ti-st: make array read_ver_cmd static, shrinks object size
...
We recently modified pps_register_source() to return error pointers
instead of NULL but it seems like there was a merge issue and part of
the commit was lost. Anyway, the ptp_clock_register() function needs to
be updated to check for IS_ERR() as well.
Fixes: 3b1ad360ac ("pps: using ERR_PTR instead of NULL while pps_register_source fails")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix smatch warning:
drivers/ptp/ptp_clock.c:298 ptp_clock_register() warn:
passing zero to 'ERR_PTR'
'err' should be set while device_create_with_groups and
pps_register_source fails
Fixes: 85a66e5501 ("ptp: create "pins" together with the rest of attributes")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a driver provides gettimex64(), use it in the PTP_SYS_OFFSET ioctl
and POSIX clock's gettime() instead of gettime64(). Drivers should
provide only one of the functions.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PTP_SYS_OFFSET ioctl, which can be used to measure the offset
between a PHC and the system clock, includes the total time that the
driver needs to read the PHC timestamp.
This typically involves reading of multiple PCI registers (sometimes in
multiple iterations) and the register that contains the lowest bits of
the timestamp is not read in the middle between the two readings of the
system clock. This asymmetry causes the measured offset to have a
significant error.
Introduce a new ioctl, driver function, and helper functions, which
allow the reading of the lowest register to be isolated from the other
readings in order to reduce the asymmetry. The ioctl returns three
timestamps for each measurement:
- system time right before reading the lowest bits of the PHC timestamp
- PHC time
- system time immediately after reading the lowest bits of the PHC
timestamp
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If a gettime64 call fails, return the error and avoid copying data back
to user.
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reorder declarations of variables as reversed Christmas tree.
Cc: Richard Cochran <richardcochran@gmail.com>
Suggested-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Building with -Wformat-nonliteral, gcc complains
drivers/ptp/ptp_clock.c: In function ‘ptp_clock_register’:
drivers/ptp/ptp_clock.c:239:26: warning: format not a string literal and no format arguments [-Wformat-nonliteral]
worker_name : info->name);
kthread_create_worker takes fmt+varargs to set the name of the
worker, and that happens with a vsnprintf() to a stack buffer (that is
then copied into task_comm). So there's no reason not to just pass
"ptp%d", ptp->index to kthread_create_worker() and avoid the
intermediate worker_name variable.
Signed-off-by: Rasmus Villemoes <linux@rasmusvillemoes.dk>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We should get 'driver_data' from 'struct device' directly. Going via
platform_device is an unneeded step back and forth.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pin_index can be indirectly controlled by user-space, hence leading
to a potential exploitation of the Spectre variant 1 vulnerability.
This issue was detected with the help of Smatch:
drivers/ptp/ptp_chardev.c:253 ptp_ioctl() warn: potential spectre issue
'ops->pin_config' [r] (local cap)
Fix this by sanitizing pin_index before using it to index
ops->pin_config, and before passing it as an argument to
function ptp_set_pinfunc(), in which it is used to index
info->pin_config.
Notice that given that speculation windows are large, the policy is
to kill the speculation on the first load and not worry if it can be
completed with a dependent load/store [1].
[1] https://marc.info/?l=linux-kernel&m=152449131114778&w=2
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level
hardware bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of
the crazy out-of-tree drivers that have been floating around
for years, combined with some really hacky userspace
implementations. This is only for GNSS receivers, but you
have to start somewhere, and this is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and existing
drivers.
Full details of everything is in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCW3g7ew8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykfBgCeOG0RkSI92XVZe0hs/QYFW9kk8JYAnRBf3Qpm
cvW7a+McOoKz/MGmEKsi
=TNfn
-----END PGP SIGNATURE-----
Merge tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
This is a fix-up patch for below build issue with multi_v7_defconfig.
drivers/ptp/ptp_qoriq.o: In function `qoriq_ptp_probe':
ptp_qoriq.c:(.text+0xd0c): undefined reference to `__aeabi_uldivmod'
Fixes: 91305f2812 ("ptp_qoriq: support automatic configuration for ptp timer")
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to support automatic configuration for ptp timer.
If required ptp dts properties are not provided, driver could
try to calculate a set of default configurations to initialize
the ptp timer. This makes the driver work for many boards which
don't have the required ptp dts properties in current kernel.
Also the users could set dts properties by themselves according
to their requirement.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems that a *break* is missing in order to avoid falling through
to the default case. Otherwise, checking *chan* makes no sense.
Fixes: 72df7a7244 ("ptp: Allow reassigning calibration pin function")
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch is to support DPAA (Data Path Acceleration Architecture)
1588 timer by adding "fsl,fman-ptp-timer" compatible, sharing
interrupt with FMan, adding FSL_DPAA_ETH dependency, and fixing
up register offset.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Madalin Bucur <madalin.bucur@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
getnstimeofday64() is deprecated and getting replaced throughout
the kernel with ktime_get_*() based helpers for a more consistent
interface.
The two functions do the exact same thing, so this is just
a cosmetic change.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is to move some definitions in ptp_qoriq.c
to the header file.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gianfar_ptp was the PTP clock driver for 1588 timer
module of Freescale QorIQ eTSEC (Enhanced Three-Speed
Ethernet Controllers) platforms. Actually QorIQ DPAA
(Data Path Acceleration Architecture) platforms is
also using the same 1588 timer module in hardware.
This patch is to rework gianfar_ptp as QorIQ common
PTP driver to support both DPAA and eTSEC. Moved
gianfar_ptp.c to drivers/ptp/, renamed it as
ptp_qoriq.c, and renamed many variables. There were
not any function changes.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use ns_to_timespec64() and timespec64_to_ns() instead of open coding
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQEcBAABAgAGBQJaDdh4AAoJELDendYovxMvPFAH/2QjTys2ydIAdmwke4odpJ7U
xuy7HOQCzOeZ5YsZthzCBsN90VmnDM7X7CcB8weSdjcKlXMSAWD+J1RgkL2iAJhI
8tzIEXECrlNuz4V5mX9TmMgtPCr4qzU3fsts0pZy4fYDq1PVWDefqOwEtbpbWabb
wRSMq/nTb9iASTMgheSC0WfhJneqtJ+J20zrzkGPCBPRFcwfppeP8/7vpkmJslBi
eH/pfchICM4w093T/BfavnsPvhLdjgRuwVzn6+e46s4tLnZAxnLRVQ7SXZXzBORq
/dL/qC0XH3YXdU+XfIs//giZsmLns6SxZaMr4vs6TxFtuzZBKpLtkOKo9zndvxk=
=sZY5
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull xen updates from Juergen Gross:
"Xen features and fixes for v4.15-rc1
Apart from several small fixes it contains the following features:
- a series by Joao Martins to add vdso support of the pv clock
interface
- a series by Juergen Gross to add support for Xen pv guests to be
able to run on 5 level paging hosts
- a series by Stefano Stabellini adding the Xen pvcalls frontend
driver using a paravirtualized socket interface"
* tag 'for-linus-4.15-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip: (34 commits)
xen/pvcalls: fix potential endless loop in pvcalls-front.c
xen/pvcalls: Add MODULE_LICENSE()
MAINTAINERS: xen, kvm: track pvclock-abi.h changes
x86/xen/time: setup vcpu 0 time info page
x86/xen/time: set pvclock flags on xen_time_init()
x86/pvclock: add setter for pvclock_pvti_cpu0_va
ptp_kvm: probe for kvm guest availability
xen/privcmd: remove unused variable pageidx
xen: select grant interface version
xen: update arch/x86/include/asm/xen/cpuid.h
xen: add grant interface version dependent constants to gnttab_ops
xen: limit grant v2 interface to the v1 functionality
xen: re-introduce support for grant v2 interface
xen: support priv-mapping in an HVM tools domain
xen/pvcalls: remove redundant check for irq >= 0
xen/pvcalls: fix unsigned less than zero error check
xen/time: Return -ENODEV from xen_get_wallclock()
xen/pvcalls-front: mark expected switch fall-through
xen: xenbus_probe_frontend: mark expected switch fall-throughs
xen/time: do not decrease steal time after live migration on xen
...
Right now there is only a pvclock_pvti_cpu0_va() which is defined
on kvmclock since:
commit dac16fba6f
("x86/vdso: Get pvclock data from the vvar VMA instead of the fixmap")
The only user of this interface so far is kvm. This commit adds a
setter function for the pvti page and moves pvclock_pvti_cpu0_va
to pvclock, which is a more generic place to have it; and would
allow other PV clocksources to use it, such as Xen.
While moving pvclock_pvti_cpu0_va into pvclock, rename also this
function to pvclock_get_pvti_cpu0_va (including its call sites)
to be symmetric with the setter (pvclock_set_pvti_cpu0_va).
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Acked-by: Andy Lutomirski <luto@kernel.org>
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
In the event of moving pvclock_pvti_cpu0_va() definition to common
pvclock code, this function would return a value on non KVM guests.
Later on this would fail with a GPF on ptp_kvm_init when running on a
Xen guest. Therefore, ptp_kvm_init() should check whether it is running
in a KVM guest.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Acked-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make these const as they are only used in a copy operation.
Done using Coccinelle.
@match disable optional_qualifier@
identifier s;
@@
static struct ptp_clock_info s = {...};
@ref@
position p;
identifier match.s;
@@
s@p
@good1@
position ref.p;
identifier match.s,f,c;
expression e;
@@
(
e = s@p
|
e = s@p.f
|
c(...,s@p.f,...)
|
c(...,s@p,...)
)
@bad depends on !good1@
position ref.p;
identifier match.s;
@@
s@p
@depends on forall !bad disable optional_qualifier@
identifier match.s;
@@
static
+ const
struct ptp_clock_info s;
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many PTP drivers required to perform some asynchronous or periodic work,
like periodically handling PHC counter overflow or handle delayed timestamp
for RX/TX network packets. In most of the cases, such work is implemented
using workqueues. Unfortunately, Kernel workqueues might introduce
significant delay in work scheduling under high system load and on -RT,
which could cause misbehavior of PTP drivers due to internal counter
overflow, for example, and there is no way to tune its execution policy and
priority manuallly.
Hence, The kthread_worker can be used insted of workqueues, as it create
separte named kthread for each worker and its its execution policy and
priority can be configured using chrt tool.
This prblem was reported for two drivers TI CPSW CPTS and dp83640, so
instead of modifying each of these driver it was proposed to add PTP
auxiliary worker to the PHC subsystem.
The patch adds PTP auxiliary worker in PHC subsystem using kthread_worker
and kthread_delayed_work and introduces two new PHC subsystem APIs:
- long (*do_aux_work)(struct ptp_clock_info *ptp) callback in
ptp_clock_info structure, which driver should assign if it require to
perform asynchronous or periodic work. Driver should return the delay of
the PTP next auxiliary work scheduling time (>=0) or negative value in case
further scheduling is not required.
- int ptp_schedule_worker(struct ptp_clock *ptp, unsigned long delay) which
allows schedule PTP auxiliary work.
The name of kthread_worker thread corresponds PTP PHC device name "ptp%d".
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With gcc 4.1.2:
drivers/ptp/ptp_dte.c: In function ‘dte_write_nco_delta’:
drivers/ptp/ptp_dte.c:105: warning: integer constant is too large for ‘long’ type
drivers/ptp/ptp_dte.c:112: warning: integer constant is too large for ‘long’ type
drivers/ptp/ptp_dte.c:114: warning: integer constant is too large for ‘long’ type
Add the missing "LL" suffix to fix this.
Fixes: 8a56aa107f ("ptp: Add a ptp clock driver for Broadcom DTE")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a ptp clock driver for the Broadcom SoCs using
the Digital timing Engine (DTE) nco.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull timer updates from Thomas Gleixner:
"The timer departement delivers:
- more year 2038 rework
- a massive rework of the arm achitected timer
- preparatory patches to allow NTP correction of clock event devices
to avoid early expiry
- the usual pile of fixes and enhancements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (91 commits)
timer/sysclt: Restrict timer migration sysctl values to 0 and 1
arm64/arch_timer: Mark errata handlers as __maybe_unused
Clocksource/mips-gic: Remove redundant non devicetree init
MIPS/Malta: Probe gic-timer via devicetree
clocksource: Use GENMASK_ULL in definition of CLOCKSOURCE_MASK
acpi/arm64: Add SBSA Generic Watchdog support in GTDT driver
clocksource: arm_arch_timer: add GTDT support for memory-mapped timer
acpi/arm64: Add memory-mapped timer support in GTDT driver
clocksource: arm_arch_timer: simplify ACPI support code.
acpi/arm64: Add GTDT table parse driver
clocksource: arm_arch_timer: split MMIO timer probing.
clocksource: arm_arch_timer: add structs to describe MMIO timer
clocksource: arm_arch_timer: move arch_timer_needs_of_probing into DT init call
clocksource: arm_arch_timer: refactor arch_timer_needs_probing
clocksource: arm_arch_timer: split dt-only rate handling
x86/uv/time: Set ->min_delta_ticks and ->max_delta_ticks
unicore32/time: Set ->min_delta_ticks and ->max_delta_ticks
um/time: Set ->min_delta_ticks and ->max_delta_ticks
tile/time: Set ->min_delta_ticks and ->max_delta_ticks
score/time: Set ->min_delta_ticks and ->max_delta_ticks
...
struct timespec is not y2038 safe on 32 bit machines.
The posix clocks apis use struct timespec directly and through struct
itimerspec.
Replace the posix clock interfaces to use struct timespec64 and struct
itimerspec64 instead. Also fix up their implementations accordingly.
Note that the clock_getres() interface has also been changed to use
timespec64 even though this particular interface is not affected by the
y2038 problem. This helps verification for internal kernel code for y2038
readiness by getting rid of time_t/ timeval/ timespec.
Signed-off-by: Deepa Dinamani <deepa.kernel@gmail.com>
Cc: arnd@arndb.de
Cc: y2038@lists.linaro.org
Cc: netdev@vger.kernel.org
Cc: Richard Cochran <richardcochran@gmail.com>
Cc: john.stultz@linaro.org
Link: http://lkml.kernel.org/r/1490555058-4603-3-git-send-email-deepa.kernel@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
drivers/ptp/ptp_kvm.c:229:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
CC: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
200 commits and noteworthy changes for most architectures.
* ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
* MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU notifiers
to support copy-on-write, KSM, idle page tracking, swapping, ballooning
and everything else. KVM_CAP_READONLY_MEM is also supported, so that
writes to some memory regions can be treated as MMIO. The new MMU also
paves the way for hardware virtualization support.
* PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
* s390: expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
* x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown in
and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
* generic:
- alternative signaling mechanism that doesn't pound on tsk->sighand->siglock
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJYral1AAoJEL/70l94x66DbNgH/Rx8YXuidFq2fe3RWOvld3RK
85OM/D5g38cTLpBE0/sJpcvX34iYN8U/l5foCZwpxB+83GHEk2Cr57JyfTogdaAJ
x8dBhHKQCA/HxSQUQLN6nFqRV+yT8WUR92Fhqx82+80BSen5Yzcfee/TDoW6T1IW
g8CYgX9FrRaGOX066ImAuUfdAdUVjyssfs9VttDTX+HiusPeuBPx/wsRe1ZEEPlH
vnltIJQb1ETV2GOZLUojKjzH6aZkjIl29XxjkYii9JTUornClG0DfW+5QT3uLrB5
gJ+G+Zmpsq8ZBx9jNDtAi7sFsoPY1Mzf+JPNCGXBra2sP2GrBAuXcxmgznRYltQ=
=8IIp
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull KVM updates from Paolo Bonzini:
"4.11 is going to be a relatively large release for KVM, with a little
over 200 commits and noteworthy changes for most architectures.
ARM:
- GICv3 save/restore
- cache flushing fixes
- working MSI injection for GICv3 ITS
- physical timer emulation
MIPS:
- various improvements under the hood
- support for SMP guests
- a large rewrite of MMU emulation. KVM MIPS can now use MMU
notifiers to support copy-on-write, KSM, idle page tracking,
swapping, ballooning and everything else. KVM_CAP_READONLY_MEM is
also supported, so that writes to some memory regions can be
treated as MMIO. The new MMU also paves the way for hardware
virtualization support.
PPC:
- support for POWER9 using the radix-tree MMU for host and guest
- resizable hashed page table
- bugfixes.
s390:
- expose more features to the guest
- more SIMD extensions
- instruction execution protection
- ESOP2
x86:
- improved hashing in the MMU
- faster PageLRU tracking for Intel CPUs without EPT A/D bits
- some refactoring of nested VMX entry/exit code, preparing for live
migration support of nested hypervisors
- expose yet another AVX512 CPUID bit
- host-to-guest PTP support
- refactoring of interrupt injection, with some optimizations thrown
in and some duct tape removed.
- remove lazy FPU handling
- optimizations of user-mode exits
- optimizations of vcpu_is_preempted() for KVM guests
generic:
- alternative signaling mechanism that doesn't pound on
tsk->sighand->siglock"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (195 commits)
x86/kvm: Provide optimized version of vcpu_is_preempted() for x86-64
x86/paravirt: Change vcp_is_preempted() arg type to long
KVM: VMX: use correct vmcs_read/write for guest segment selector/base
x86/kvm/vmx: Defer TR reload after VM exit
x86/asm/64: Drop __cacheline_aligned from struct x86_hw_tss
x86/kvm/vmx: Simplify segment_base()
x86/kvm/vmx: Get rid of segment_base() on 64-bit kernels
x86/kvm/vmx: Don't fetch the TSS base from the GDT
x86/asm: Define the kernel TSS limit in a macro
kvm: fix page struct leak in handle_vmon
KVM: PPC: Book3S HV: Disable HPT resizing on POWER9 for now
KVM: Return an error code only as a constant in kvm_get_dirty_log()
KVM: Return an error code only as a constant in kvm_get_dirty_log_protect()
KVM: Return directly after a failed copy_from_user() in kvm_vm_compat_ioctl()
KVM: x86: remove code for lazy FPU handling
KVM: race-free exit from KVM_RUN without POSIX signals
KVM: PPC: Book3S HV: Turn "KVM guest htab" message into a debug message
KVM: PPC: Book3S PR: Ratelimit copy data failure error messages
KVM: Support vCPU-based gfn->hva cache
KVM: use separate generations for each address space
...
Let's switch to using device_create_with_groups(), which will allow us to
create "pins" attribute group together with the rest of ptp device
attributes, and before userspace gets notified about ptp device creation.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of creating selected attributes after the device is created (and
after userspace potentially seen uevent), lets use attribute group
is_visible() method to control which attributes are shown. This will allow
us to create all attributes (except "pins" group, which will be taken care
of later) before userspace gets notified about new ptp class device.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kcalloc is more semantically correct when allocating arrays of objects, and
overflow-safe.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do not need explicitly call dev_set_drvdata(), as it is done for us by
device_create().
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
No point in registering the device if it cannot work.
The hypercall does not advertise itself, so we have to call it.
Signed-off-by: Radim Krčmář <rkrcmar@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Add a driver with gettime method returning hosts realtime clock.
This allows Chrony to synchronize host and guest clocks with
high precision (see results below).
chronyc> sources
MS Name/IP address Stratum Poll Reach LastRx Last sample
===============================================================================
To configure Chronyd to use PHC refclock, add the
following line to its configuration file:
refclock PHC /dev/ptpX poll 3 dpoll -2 offset 0
Where /dev/ptpX is the kvmclock PTP clock.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Pull timer updates from Thomas Gleixner:
"The time/timekeeping/timer folks deliver with this update:
- Fix a reintroduced signed/unsigned issue and cleanup the whole
signed/unsigned mess in the timekeeping core so this wont happen
accidentaly again.
- Add a new trace clock based on boot time
- Prevent injection of random sleep times when PM tracing abuses the
RTC for storage
- Make posix timers configurable for real tiny systems
- Add tracepoints for the alarm timer subsystem so timer based
suspend wakeups can be instrumented
- The usual pile of fixes and updates to core and drivers"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (23 commits)
timekeeping: Use mul_u64_u32_shr() instead of open coding it
timekeeping: Get rid of pointless typecasts
timekeeping: Make the conversion call chain consistently unsigned
timekeeping_Force_unsigned_clocksource_to_nanoseconds_conversion
alarmtimer: Add tracepoints for alarm timers
trace: Update documentation for mono, mono_raw and boot clock
trace: Add an option for boot clock as trace clock
timekeeping: Add a fast and NMI safe boot clock
timekeeping/clocksource_cyc2ns: Document intended range limitation
timekeeping: Ignore the bogus sleep time if pm_trace is enabled
selftests/timers: Fix spelling mistake "Asyncrhonous" -> "Asynchronous"
clocksource/drivers/bcm2835_timer: Unmap region obtained by of_iomap
clocksource/drivers/arm_arch_timer: Map frame with of_io_request_and_map()
arm64: dts: rockchip: Arch counter doesn't tick in system suspend
clocksource/drivers/arm_arch_timer: Don't assume clock runs in suspend
posix-timers: Make them configurable
posix_cpu_timers: Move the add_device_randomness() call to a proper place
timer: Move sys_alarm from timer.c to itimer.c
ptp_clock: Allow for it to be optional
Kconfig: Regenerate *.c_shipped files after previous changes
...
Some embedded systems have no use for them. This removes about
25KB from the kernel binary size when configured out.
Corresponding syscalls are routed to a stub logging the attempt to
use those syscalls which should be enough of a clue if they were
disabled without proper consideration. They are: timer_create,
timer_gettime: timer_getoverrun, timer_settime, timer_delete,
clock_adjtime, setitimer, getitimer, alarm.
The clock_settime, clock_gettime, clock_getres and clock_nanosleep
syscalls are replaced by simple wrappers compatible with CLOCK_REALTIME,
CLOCK_MONOTONIC and CLOCK_BOOTTIME only which should cover the vast
majority of use cases with very little code.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-kbuild@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Michal Marek <mmarek@suse.com>
Cc: Edward Cree <ecree@solarflare.com>
Link: http://lkml.kernel.org/r/1478841010-28605-7-git-send-email-nicolas.pitre@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In order to break the hard dependency between the PTP clock subsystem and
ethernet drivers capable of being clock providers, this patch provides
simple PTP stub functions to allow linkage of those drivers into the
kernel even when the PTP subsystem is configured out. Drivers must be
ready to accept NULL from ptp_clock_register() in that case.
And to make it possible for PTP to be configured out, the select statement
in those driver's Kconfig menu entries is converted to the new "imply"
statement. This way the PTP subsystem may have Kconfig dependencies of
its own, such as POSIX_TIMERS, without having to make those ethernet
drivers unavailable if POSIX timers are cconfigured out. And when support
for POSIX timers is selected again then the default config option for PTP
clock support will automatically be adjusted accordingly.
The pch_gbe driver is a bit special as it relies on extra code in
drivers/ptp/ptp_pch.c. Therefore we let the make process descend into
drivers/ptp/ even if PTP_1588_CLOCK is unselected.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Acked-by: Edward Cree <ecree@solarflare.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Cc: Paul Bolle <pebolle@tiscali.nl>
Cc: linux-kbuild@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: Michal Marek <mmarek@suse.com>
Link: http://lkml.kernel.org/r/1478841010-28605-4-git-send-email-nicolas.pitre@linaro.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The internal PTP Hardware Clock (PHC) interface limits the resolution for
frequency adjustments to one part per billion. However, some hardware
devices allow finer adjustment, and making use of the increased resolution
improves synchronization measurably on such devices.
This patch adds an alternative method that allows finer frequency tuning
by passing the scaled ppm value to PHC drivers. This value comes from
user space, and it has a resolution of about 0.015 ppb. We also deprecate
the older method, anticipating its removal once existing drivers have been
converted over.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Suggested-by: Ulrik De Bie <ulrik.debie-os@e2big.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
YueHaibing