Similar like the previous commit, cover with chip->shutdown_rwsem
and chip->shutdown checks.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace mutex with rwsem for codec->shutdown protection so that
concurrent accesses are allowed.
Also add the protection to snd_usb_autosuspend() and
snd_usb_autoresume(), too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Close some races at disconnection of a USB audio device by adding the
chip->shutdown_mutex and chip->shutdown check at appropriate places.
The spots to put bandaids are:
- PCM prepare, hw_params and hw_free
- where the usb device is accessed for communication or get speed, in
mixer.c and others; the device speed is now cached in subs->speed
instead of accessing to chip->dev
The accesses in PCM open and close don't need the mutex protection
because these are already handled in the core PCM disconnection code.
The autosuspend/autoresume codes are still uncovered by this patch
because of possible mutex deadlocks. They'll be covered by the
upcoming change to rwsem.
Also the mixer codes are untouched, too. These will be fixed in
another patch, too.
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix races at PCM disconnection:
- while a PCM device is being opened or closed
- while the PCM state is being changed without lock in prepare,
hw_params, hw_free ops
Reported-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
xfstests has always had random failures of tests due to loop devices
failing to be torn down and hence leaving filesytems that cannot be
unmounted. This causes test runs to immediately stop.
Over the past 6 or 7 years we've added hacks like explicit unmount
-d commands for loop mounts, losetup -d after unmount -d fails, etc,
but still the problems persist. Recently, the frequency of loop
related failures increased again to the point that xfstests 259 will
reliably fail with a stray loop device that was not torn down.
That is despite the fact the test is above as simple as it gets -
loop 5 or 6 times running mkfs.xfs with different paramters:
lofile=$(losetup -f)
losetup $lofile "$testfile"
"$MKFS_XFS_PROG" -b size=512 $lofile >/dev/null || echo "mkfs failed!"
sync
losetup -d $lofile
And losteup -d $lofile is failing with EBUSY on 1-3 of these loops
every time the test is run.
Turns out that blkid is running simultaneously with losetup -d, and
so it sees an elevated reference count and returns EBUSY. But why
is blkid running? It's obvious, isn't it? udev has decided to try
and find out what is on the block device as a result of a creation
notification. And it is racing with mkfs, so might still be scanning
the device when mkfs finishes and we try to tear it down.
So, make losetup -d force autoremove behaviour. That is, when the
last reference goes away, tear down the device. xfstests wants it
*gone*, not causing random teardown failures when we know that all
the operations the tests have specifically run on the device have
completed and are no longer referencing the loop device.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Added appropriate timeout value for secure erase based on identify device data
Signed-off-by: Asai Thambi S P <asamymuthupa@micron.com>
Signed-off-by: Selvan Mani <smani@micron.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Changing the type of bdev parameters to be unsigned int :1, rather than bool.
This is more consistent with the types of other features in the block drivers.
Signed-off-by: Oliver Chick <oliver.chick@citrix.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The patch cciss-use-check_signature.patch in -mm tree introduced
a build error:
drivers/built-in.o: In function `CISS_signature_present':
drivers/block/cciss.c:4270: undefined reference to `check_signature'
Add missing CONFIG_CHECK_SIGNATURE to fix this issue.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Fengguang Wu <wfg@linux.intel.com>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Acked-by: "Stephen M. Cameron" <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The memory return by kzalloc() or kmem_cache_zalloc() has already be set
to zero, so remove useless memset(0).
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: Mike Miller <mike.miller@hp.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Using kmem_cache_zalloc() instead of kmem_cache_alloc() and memset().
spatch with a semantic match is used to found this problem.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Peter is not going to maintain the driver any more. I have the
hardware.
Acked-by: Peter Osterlund <petero2@telia.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This is a small cleanup, that also may turn error handling of
unitialized disks more readable. We don't need a separate variable to
track allocated disks, remove dr and reuse drive variable instead.
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The same checks to see if a drive can be or is registered are
repeated through the code, factor out the checks in a common function
and replace the repeated checks with it.
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
On floppy initialization, if something failed inside the loop we call
add_disk, there was no cleanup of previous iterations in the error
handling.
Cc: stable@vger.kernel.org
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
If blk_init_queue fails, we do not call put_disk on the current dr
(dr is decremented first in the error handling loop).
Cc: stable@vger.kernel.org
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Since commit 070ad7e ("floppy: convert to delayed work and single-thread
wq"), we end up calling alloc_ordered_workqueue multiple times inside
the loop, which shouldn't be intended. Besides the leak, other side
effect in the current code is if blk_init_queue fails, we would end up
calling unregister_blkdev even if we didn't call yet register_blkdev.
Just moved the allocation of floppy_wq before the loop, and adjusted the
code accordingly.
Cc: stable@vger.kernel.org # 3.5+
Acked-by: Vivek Goyal <vgoyal@redhat.com>
Reviewed-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
drivers/block/xen-blkback/xenbus.c:260:5: warning: symbol 'xenvbd_sysfs_addif' was not declared. Should it be static?
drivers/block/xen-blkback/xenbus.c:284:6: warning: symbol 'xenvbd_sysfs_delif' was not declared. Should it be static?
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull Ceph fixes form Sage Weil:
"There are two fixes in the messenger code, one that can trigger a NULL
dereference, and one that error in refcounting (extra put). There is
also a trivial fix that in the fs client code that is triggered by NFS
reexport."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
ceph: fix dentry reference leak in encode_fh()
libceph: avoid NULL kref_put when osd reset races with alloc_msg
rbd: reset BACKOFF if unable to re-queue
Call to d_find_alias() needs a corresponding dput()
This fixes http://tracker.newdream.net/issues/3271
Signed-off-by: David Zafman <david.zafman@inktank.com>
Reviewed-by: Sage Weil <sage@inktank.com>
commit 119c0d4460 changed
ext4_new_inode() such that the inode bitmap was being modified
outside a transaction, which could lead to corruption, and was
discovered when journal_checksum found a bad checksum in the
journal during log replay.
Nix ran into this when using the journal_async_commit mount
option, which enables journal checksumming. The ensuing
journal replay failures due to the bad checksums led to
filesystem corruption reported as the now infamous
"Apparent serious progressive ext4 data corruption bug"
[ Changed by tytso to only call ext4_journal_get_write_access() only
when we're fairly certain that we're going to allocate the inode. ]
I've tested this by mounting with journal_checksum and
running fsstress then dropping power; I've also tested by
hacking DM to create snapshots w/o first quiescing, which
allows me to test journal replay repeatedly w/o actually
power-cycling the box. Without the patch I hit a journal
checksum error every time. With this fix it survives
many iterations.
Reported-by: Nix <nix@esperi.org.uk>
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: stable@vger.kernel.org
Pull i2c subsystem fixes from Jean Delvare.
* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
i2c-i801: Fix comment
i2c-i801: Simplify dependency towards GPIOLIB
i2c-stub: Move to drivers/i2c
Arbitrarily selecting GPIOLIB causes trouble on some architectures,
so don't do that. Instead, just make the optional multiplexing code
depend on CONFIG_I2C_MUX_GPIO instead of CONFIG_I2C_MUX for now. We
can revisit if the i2c-i801 driver ever supports other multiplexing
flavors.
Also make that optional code depend on DMI, as it won't do anything
without that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Move the i2c-stub driver to drivers/i2c, to match the Kconfig entry.
This is less confusing that way.
I also fixed all checkpatch warnings and errors.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Peter Huewe <peterhuewe@gmx.de>
were not being brought up. I found that the modules for the
network was not being installed. This was due to the config
CONFIG_MODULES_USE_ELF_RELA that came before CONFIG_MODULES, and
confused ktest in thinking that CONFIG_MODULES=y was not found.
Ktest needs to test all configs and not just stop if something starts
with CONFIG_MODULES.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQEcBAABAgAGBQJQig8hAAoJEOdOSU1xswtMkFgIALLcnba79RHsPdGCTX247Hcg
UdteytZgyd1XayDSPLOVAR5f1vJeZ/6/L5dwWqZpf+j6wUTBwdUTc4DlBwHNpi8V
XDKbwAYWAQp4BVaQkKcrxKZZepE791NWxCelG7T7S0d7jIkwFTA4BhT4+8+QFztZ
H5IDL+HA73Jvehfv3gpJW6yDQ/QSyUjIK4QCsJS+wodB9nDzhAEiZ6ZKflSXFGq4
J+Fl/UfRfnA+j0aP75ecL7hewfdiLOmK67vKvW3l8wZ7s0y3NnIsxymmaa6sTIAQ
lIAsmSPdqOzXExIKLBHnsHCog6UW4a91MmEqM05IDpt+AcCnwDbk4EfbJEXa8ug=
=vl1t
-----END PGP SIGNATURE-----
Merge tag 'ktest-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest
Pull ktest confusion fix from Steven Rostedt:
"With the v3.7-rc2 kernel, the network cards on my target boxes were
not being brought up.
I found that the modules for the network was not being installed.
This was due to the config CONFIG_MODULES_USE_ELF_RELA that came
before CONFIG_MODULES, and confused ktest in thinking that
CONFIG_MODULES=y was not found.
Ktest needs to test all configs and not just stop if something starts
with CONFIG_MODULES."
* tag 'ktest-v3.7-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-ktest:
ktest: Fix ktest confusion with CONFIG_MODULES_USE_ELF_RELA
These fixes are both pretty minor ones and are driver local.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=3xEy
-----END PGP SIGNATURE-----
Merge tag 'spi-mxs' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc
Pull minor spi MXS fixes from Mark Brown:
"These fixes are both pretty minor ones and are driver local."
* tag 'spi-mxs' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/misc:
spi: mxs: Terminate DMA in case of DMA timeout
spi: mxs: Assign message status after transfer finished
Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we
had a few of these patches cause regressions themselves and had to
work out how to deal with those in the meantime.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=IDdm
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc fixes from Arnd Bergmann:
"Bug fixes for a number of ARM platforms, mostly OMAP, imx and at91.
These come a little later than I had hoped but unfortunately we had a
few of these patches cause regressions themselves and had to work out
how to deal with those in the meantime."
* tag 'fixes-for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits)
Revert "ARM i.MX25: Fix PWM per clock lookups"
ARM: versatile: fix versatile_defconfig
ARM: mvebu: update defconfig with 3.7 changes
ARM: at91: fix at91x40 build
ARM: socfpga: Fix socfpga compilation with early_printk() enabled
ARM: SPEAr: Remove unused empty files
MAINTAINERS: Add arm-soc tree entry
ARM: dts: mxs: add the "clock-names" for gpmi-nand
ARM: ux500: Correct SDI5 address and add some format changes
ARM: ux500: Specify AMBA Primecell IDs for Nomadik I2C in DT
ARM: ux500: Fix build error relating to IRQCHIP_SKIP_SET_WAKE
ARM: at91: drop duplicated config SOC_AT91SAM9 entry
ARM: at91/i2c: change id to let i2c-at91 work
ARM: at91/i2c: change id to let i2c-gpio work
ARM: at91/dts: at91sam9g20ek_common: Fix typos in buttons labels.
ARM: at91: fix external interrupt specification in board code
ARM: at91: fix external interrupts in non-DT case
ARM: at91: at91sam9g10: fix SOC type detection
ARM: at91/tc: fix typo in the DT document
ARM: AM33XX: Fix configuration of dmtimer parent clock by dmtimer driverDate:Wed, 17 Oct 2012 13:55:55 -0500
...
Functions generic_file_splice_read and generic_file_splice_write access
the pagecache directly. For block devices these functions must be locked
so that block size is not changed while they are in progress.
This patch is an additional fix for commit b87570f5d3 ("Fix a crash
when block device is read and block size is changed at the same time")
that locked aio_read, aio_write and mmap against block size change.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use rcu_read_lock_sched / rcu_read_unlock_sched / synchronize_sched
instead of rcu_read_lock / rcu_read_unlock / synchronize_rcu.
This is an optimization. The RCU-protected region is very small, so
there will be no latency problems if we disable preempt in this region.
So we use rcu_read_lock_sched / rcu_read_unlock_sched that translates
to preempt_disable / preempt_disable. It is smaller (and supposedly
faster) than preemptible rcu_read_lock / rcu_read_unlock.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch introduces new barrier pair light_mb() and heavy_mb() for
percpu rw semaphores.
This patch fixes a bug in percpu-rw-semaphores where a barrier was
missing in percpu_up_write.
This patch improves performance on the read path of
percpu-rw-semaphores: on non-x86 cpus, there was a smp_mb() in
percpu_up_read. This patch changes it to a compiler barrier and removes
the "#if defined(X86) ..." condition.
From: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Clean up some fallout from the OMAP header reorganisation and a minor
fix for DMIC which has no practical effect but is neater.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJQjFnSAAoJELSic+t+oim9vO4P/3uAd9BxxDJe6X4wFdNO2/qn
3kgihOX/uhA0x6gZUmXnoNClM6Mxwm61dz88FZ+IsU92MTxQAKwa5jnW5CsuaDkv
t6AWbhQ6tHVz4OJ54Vtq+PirYNXe9+mldBPYaPfke06R6eaat7XkU0HG9342GKqv
bcHn+ON0vzN89QlxLvnt+wbaOJitXrFnGLLgnAEhwkhjfJgZ6bN5a8uB7IuG4F4g
2IYMh6hbsirWm3nG7oVynAG6gZzYyqLf4uVA5AY5DREUfSu0oVjlHa0v9EjRIFK3
7a7NcZ8MRNr7bfEa1xQFssVhPAdj4xrqRoYyb3dsCQwj8Gsj6rca4tC1dHBT4FdM
dtNNCfcypEFBBfs5RZ1eSvIfqIJNI3isBILbnJ+lIF8rmxalsoLZuRDWqXDh7ryH
8RAGNfggxjUpxLjddcsX+LeLZgQYt61Su+69Anc1xt+N2S//in9PXhbsWR6/GgUS
Ke03g0fqmfVpoG54eqCVX1qg0qKiScCWYDpbTBPNO93yzYzszk2HfY1RtVx2dLjP
n99haf2wYC4YL0+wAFYgNRY6hQ85hAZRLG0exafKrFwnVIpCukcHc47nZ8M3DF3E
xBhxMhxQSSfAMcbn1QtMPMm7w7YpXzSw/7amKrNL2ifY/L31G/8GJ+kNgxtIot0H
Yx8TM2usfb8FCeJ48k+V
=F87m
-----END PGP SIGNATURE-----
Merge tag 'asoc-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.7
Clean up some fallout from the OMAP header reorganisation and a minor
fix for DMIC which has no practical effect but is neater.
We should really use "fck" when asking for the functional clock and not
"dmic_fck".
This way we can ensure that multiple dmic modules can exist in the system.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also drop the includes that are no longer needed and just
cause problems for the ARM common zImage.
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
[tony@atomide.com: updated to drop unneeded headers]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This change was originally titled "gpio/omap: fix off-mode bug: clear debounce
clock enable mask on free/reset". The title has been updated slightly to
reflect (what should be) the final fix.
When a GPIO is freed or shutdown, we need to ensure that any debounce settings
are cleared and if the GPIO is the only GPIO in the bank that is currently
using debounce, then disable the debounce clock as well to save power.
Currently, the debounce settings are not cleared on a GPIO free or shutdown and
so during a context restore on subsequent off-mode transition, the previous
debounce values are restored from the shadow copies (bank->context.debounce*)
leading to mismatch state between driver state and hardware state.
This was discovered when board code was doing
gpio_request_one()
gpio_set_debounce()
gpio_free()
which was leaving the GPIO debounce settings in a confused state. If that GPIO
bank is subsequently used with off-mode enabled, bogus state would be restored,
leaving GPIO debounce enabled which then prevented the CORE powerdomain from
transitioning.
To fix this, introduce a new function called _clear_gpio_debounce() to clear
any debounce settings when the GPIO is freed or shutdown. If this GPIO is the
last debounce-enabled GPIO in the bank, the debounce will also be cut.
Please note that we cannot use _gpio_dbck_disable() to disable the debounce
clock because this has been specifically created for the gpio suspend path
and is intended to shutdown the debounce clock while debounce is enabled.
Special thanks to Kevin Hilman for root causing the bug. This fix is a
collaborative effort with inputs from Kevin Hilman, Grazvydas Ignotas and
Santosh Shilimkar.
Testing:
- This has been unit tested on an OMAP3430 Beagle board, by requesting a gpio,
enabling debounce and then freeing the gpio and checking the register
contents, the saved register context and the debounce clock state.
- Kevin Hilman tested on 37xx/EVM board which configures GPIO debounce for the
ads7846 touchscreen in its board file using the above sequence, and so was
failing off-mode tests in dynamic idle. Verified that off-mode tests are
passing with this patch.
V5 changes:
- Corrected author
Reported-by: Paul Walmsley <paul@pwsan.com>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Cc: Grazvydas Ignotas <notasas@gmail.com>
Cc: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Tested-by: Kevin Hilman <khilman@ti.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This reverts commit 92063cee11, it
was applied prematurely, causing this build error for
imx_v4_v5_defconfig:
arch/arm/mach-imx/clk-imx25.c: In function 'mx25_clocks_init':
arch/arm/mach-imx/clk-imx25.c:206:26: error: 'pwm_ipg_per' undeclared (first use in this function)
arch/arm/mach-imx/clk-imx25.c:206:26: note: each undeclared identifier is reported only once for each function it appears in
Sascha Hauer explains:
> There are several gates missing in clk-imx25.c. I have a patch which
> adds support for them and I seem to have missed that the above depends
> on it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
With the introduction of CONFIG_ARCH_MULTIPLATFORM, versatile is
no longer the default platform, so we need to enable
CONFIG_ARCH_VERSATILE explicitly in order for that to be selected
rather than the multiplatform configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The split of 370 and XP into two Kconfig options and the multiplatform
kernel support has changed a few Kconfig symbols, so let's update the
mvebu_defconfig file with the latest changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
patch 738a0fd7 "ARM: at91: fix external interrupts in non-DT case"
fixed a run-time error on some at91 platforms but did not apply
the same change to at91x40, which now doesn't build.
This changes at91x40 in the same way that the other platforms
were changed.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
With kernel 3.6 some obsolete SCSI-2 commands including SEEK_10 have
have been removed by commit 1fd032ee10
"target: move code for CDB emulation".
There are still clients out there which use these old SCSI-2 commands.
This mainly happens when running VMs with legacy guest systems,
connected via SCSI command pass-through to iSCSI targets. Make them
happy and return status GOOD.
Many real SCSI disks or external iSCSI storage devices still support
these old commands. So let's make LIO backward compatible as well.
This patch adds support for the previously removed SEEK_10 and
additionally the SEEK_6 and REZERO_UNIT commands.
Signed-off-by: Bernhard Kohl <bernhard.kohl@nsn.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Fabric drivers currently expect to internally release se_cmd in the event
of a TMR failure during target_submit_tmr(), which means the immediate call
to transport_generic_free_cmd() after TFO->queue_tm_rsp() from within
target_complete_tmr_failure() workqueue context is wrong.
This is done as some fabrics expect TMR operations to be acknowledged
before releasing the descriptor, so the assumption that core is releasing
se_cmd associated TMR memory is incorrect. This fixes a OOPs where
transport_generic_free_cmd() was being called more than once.
This bug was originally observed with tcm_qla2xxx fabric ports.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Pull networking fixes from David Miller:
"This is what we usually expect at this stage of the game, lots of
little things, mostly in drivers. With the occasional 'oops didn't
mean to do that' kind of regressions in the core code."
1) Uninitialized data in __ip_vs_get_timeouts(), from Arnd Bergmann
2) Reject invalid ACK sequences in Fast Open sockets, from Jerry Chu.
3) Lost error code on return from _rtl_usb_receive(), from Christian
Lamparter.
4) Fix reset resume on USB rt2x00, from Stanislaw Gruszka.
5) Release resources on error in pch_gbe driver, from Veaceslav Falico.
6) Default hop limit not set correctly in ip6_template_metrics[], fix
from Li RongQing.
7) Gianfar PTP code requests wrong kind of resource during probe, fix
from Wei Yang.
8) Fix VHOST net driver on big-endian, from Michael S Tsirkin.
9) Mallenox driver bug fixes from Jack Morgenstein, Or Gerlitz, Moni
Shoua, Dotan Barak, and Uri Habusha.
10) usbnet leaks memory on TX path, fix from Hemant Kumar.
11) Use socket state test, rather than presence of FIN bit packet, to
determine FIONREAD/SIOCINQ value. Fix from Eric Dumazet.
12) Fix cxgb4 build failure, from Vipul Pandya.
13) Provide a SYN_DATA_ACKED state to complement SYN_FASTOPEN in socket
info dumps. From Yuchung Cheng.
14) Fix leak of security path in kfree_skb_partial(). Fix from Eric
Dumazet.
15) Handle RX FIFO overflows more resiliently in pch_gbe driver, from
Veaceslav Falico.
16) Fix MAINTAINERS file pattern for networking drivers, from Jean
Delvare.
17) Add iPhone5 IDs to IPHETH driver, from Jay Purohit.
18) VLAN device type change restriction is too strict, and should not
trigger for the automatically generated vlan0 device. Fix from Jiri
Pirko.
19) Make PMTU/redirect flushing work properly again in ipv4, from
Steffen Klassert.
20) Fix memory corruptions by using kfree_rcu() in netlink_release().
From Eric Dumazet.
21) More qmi_wwan device IDs, from Bjørn Mork.
22) Fix unintentional change of SNAT/DNAT hooks in generic NAT
infrastructure, from Elison Niven.
23) Fix 3.6.x regression in xt_TEE netfilter module, from Eric Dumazet.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (57 commits)
tilegx: fix some issues in the SW TSO support
qmi_wwan/cdc_ether: move Novatel 551 and E362 to qmi_wwan
net: usb: Fix memory leak on Tx data path
net/mlx4_core: Unmap UAR also in the case of error flow
net/mlx4_en: Don't use vlan tag value as an indication for vlan presence
net/mlx4_en: Fix double-release-range in tx-rings
bas_gigaset: fix pre_reset handling
vhost: fix mergeable bufs on BE hosts
gianfar_ptp: use iomem, not ioports resource tree in probe
ipv6: Set default hoplimit as zero.
NET_VENDOR_TI: make available for am33xx as well
pch_gbe: fix error handling in pch_gbe_up()
b43: Fix oops on unload when firmware not found
mwifiex: clean up scan state on error
mwifiex: return -EBUSY if specific scan request cannot be honored
brcmfmac: fix potential NULL dereference
Revert "ath9k_hw: Updated AR9003 tx gain table for 5GHz"
ath9k_htc: Add PID/VID for a Ubiquiti WiFiStation
rt2x00: usb: fix reset resume
rtlwifi: pass rx setup error code to caller
...
Pull slave-dmaengine fixes from Vinod Koul:
"Three fixes for slave dmanegine.
Two are for typo omissions in sifr dmaengine driver and the last one
is for the imx driver fixing a missing unlock"
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: sirf: fix a typo in moving running dma_desc to active queue
dmaengine: sirf: fix a typo in dma_prep_interleaved
dmaengine: imx-dma: fix missing unlock on error in imxdma_xfer_desc()
* Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
* Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
* Fix for smp_processor_id() usage in preemptible code in powernow-k8 from
Andreas Herrmann.
* Fix for a suspend-related memory leak in cpufreq stats from Xiaobing Tu.
* Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD
in flush_old_exec() from Oleg Nesterov.
* acpi_processor_notify() fix from Alan Cox.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8Tcc
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael J Wysocki:
- Fix for a memory leak in acpi_bind_one() from Jesper Juhl.
- Fix for an error code path memory leak in pm_genpd_attach_cpuidle()
from Jonghwan Choi.
- Fix for smp_processor_id() usage in preemptible code in powernow-k8
from Andreas Herrmann.
- Fix for a suspend-related memory leak in cpufreq stats from Xiaobing
Tu.
- Freezer fix for failure to clear PF_NOFREEZE along with PF_KTHREAD in
flush_old_exec() from Oleg Nesterov.
- acpi_processor_notify() fix from Alan Cox.
* tag 'pm+acpi-for-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI: missing break
freezer: exec should clear PF_NOFREEZE along with PF_KTHREAD
Fix memory leak in cpufreq stats.
cpufreq / powernow-k8: Remove usage of smp_processor_id() in preemptible code
PM / Domains: Fix memory leak on error path in pm_genpd_attach_cpuidle
ACPI: Fix memory leak in acpi_bind_one()
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=1EJ/
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband fixes from Roland Dreier:
"Small batch of fixes for 3.7:
- Fix crash in error path in cxgb4
- Fix build error on 32 bits in mlx4
- Fix SR-IOV bugs in mlx4"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Perform correct resource cleanup if mlx4_QUERY_ADAPTER() fails
mlx4_core: Remove annoying debug messages from SR-IOV flow
RDMA/cxgb4: Don't free chunk that we have failed to allocate
IB/mlx4: Synchronize cleanup of MCGs in MCG paravirtualization
IB/mlx4: Fix QP1 P_Key processing in the Primary Physical Function (PPF)
IB/mlx4: Fix build error on platforms where UL is not 64 bits
It is possible for the target code to change the loop_id or s_id of a
target session in reaction to an FC fabric change. However, the
session structures are stored in tables that are indexed by these two
keys, and if we just change the session structure but leave the
pointers to it in the old places in the table, havoc can ensue. For
example, a new session might come along that should go in the old slot
in the table and overwrite the old session pointer.
To handle this, add a new tgt_ops->update_sess() method that also
updates the "by loop_id" and "by s_id" lookup tables when a session
changes, so that the keys where a session pointer is stored in these
tables always matches the keys in the session structure itself.
(nab: Drop unnecessary double inversion with FCF_CONF_COMP_SUPPORTED
usage)
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
My draft of SPC-4 says the following about the SCSI name string in
inquiry VPD page 83h:
The SCSI NAME STRING field starts with either:
a) the four UTF-8 characters 'eui.' concatenated with 16, 24, or
32 hexadecimal digits (i.e., the UTF-8 characters 0 through 9
and A through F) for an EUI-64 based identifier (see
7.8.6.5). The first hexadecimal digit shall be the most
significant four bits of the first byte (i.e., most significant
byte) of the EUI-64 based identifier;
b) the four UTF-8 characters 'naa.' concatenated with 16 or 32
hexadecimal digits for an NAA identifier (see 7.8.6.6). The
first hexadecimal digit shall be the most significant four bits
of the first byte (i.e., most significant byte) of the NAA
identifier; or
c) the four UTF-8 characters 'iqn.' concatenated with an iSCSI
Name for an iSCSI-name based identifier (see iSCSI).
However, the .tpg_get_wwn method for tcm_qla2xxx formats the WWN so
the SCSI name string looks like "52:4a:93:7d:24:5f:b2:12,t,0x0001".
This patch corrects the code so that VPD 83h gives a SPC-compliant
SCSI name string like "naa.524a937d245fb212,t,0x0001" while leavig
other uses alone (so configfs will still work with ':' separated WWNs).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
All other callers of qlt_update_vp_map() already hold ->vport_slock
while updating the vp target map, so go ahead and add the missing
->vport_slock within qla24xx_disable_vp() code.
Cc: Saurav Kashyap <saurav.kashyap@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Arun Easi <arun.easi@qlogic.com>
Cc: Andrew Vasquez <andrew.vasquez@qlogic.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Roland Dreier <roland@purestorage.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Here are a bunch of USB fixes for the 3.7-rc tree.
There's a lot of small USB serial driver fixes, and one larger one (the mos7840
driver changes are mostly just moving code around to fix problems.) Thanks to
Johan Hovold for finding the problems and fixing them all up.
Other than those, there is the usual new device ids, xhci bugfixes, and gadget
driver fixes, nothing out of the ordinary.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iEYEABECAAYFAlCKwEEACgkQMUfUDdst+ylkiQCfTgset/pmxh/LV/wtauaMITB0
mj4AoLuqOMNwBhrtbm7fBN9uilmnU5VL
=HW4O
-----END PGP SIGNATURE-----
Merge tag 'usb-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg Kroah-Hartman:
"Here are a bunch of USB fixes for the 3.7-rc tree.
There's a lot of small USB serial driver fixes, and one larger one
(the mos7840 driver changes are mostly just moving code around to fix
problems.) Thanks to Johan Hovold for finding the problems and fixing
them all up.
Other than those, there is the usual new device ids, xhci bugfixes,
and gadget driver fixes, nothing out of the ordinary.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.7-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (49 commits)
xhci: trivial: Remove assigned but unused ep_ctx.
xhci: trivial: Remove assigned but unused slot_ctx.
xhci: Fix missing break in xhci_evaluate_context_result.
xhci: Fix potential NULL ptr deref in command cancellation.
ehci: Add yet-another Lucid nohandoff pci quirk
ehci: fix Lucid nohandoff pci quirk to be more generic with BIOS versions
USB: mos7840: fix port_probe flow
USB: mos7840: fix port-data memory leak
USB: mos7840: remove invalid disconnect handling
USB: mos7840: remove NULL-urb submission
USB: qcserial: fix interface-data memory leak in error path
USB: option: fix interface-data memory leak in error path
USB: ipw: fix interface-data memory leak in error path
USB: mos7840: fix port-device leak in error path
USB: mos7840: fix urb leak at release
USB: sierra: fix port-data memory leak
USB: sierra: fix memory leak in probe error path
USB: sierra: fix memory leak in attach error path
USB: usb-wwan: fix multiple memory leaks in error paths
USB: keyspan: fix NULL-pointer dereferences and memory leaks
...
Takashi Iwai