If during transmission system error was returned, the logic was to
incorrectly deduce that chip is a TPM 1.x chip. This patch fixes this
issue. Also, this patch changes probing so that message tag is used as the
measure for TPM 2.x, which should be much more stable. A separate function
called tpm2_probe() is encapsulated because it can be used with any
chipset.
Fixes: aec04cbdf7 ("tpm: TPM 2.0 FIFO Interface")
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Fixed suspend/resume paths for TPM 2.0 and consolidated all the
associated code to the tpm_pm_suspend() and tpm_pm_resume()
functions. Resume path should be handled by the firmware, i.e.
Startup(CLEAR) for hibernate and Startup(STATE) for suspend.
There might be some non-PC embedded devices in the future where
Startup() is not the handled by the FW but fixing the code for
those IMHO should be postponed until there is hardware available
to test the fixes although extra Startup in the driver code is
essentially a NOP.
Added Shutdown(CLEAR) to the remove paths of TIS and CRB drivers.
Changed tpm2_shutdown() to a void function because there isn't
much you can do except print an error message if this fails with
a system error.
Fixes: aec04cbdf7 ("tpm: TPM 2.0 FIFO Interface")
Fixes: 30fc8d138e ("tpm: TPM 2.0 CRB Interface")
[phuewe: both did send TPM_Shutdown on resume which 'disables' the TPM
and did not send TPM2_Shutdown on teardown which leads some TPM2.0 to
believe there was an attack (no TPM2_Shutdown = no orderly shutdown =
attack)]
Reported-by: Peter Hüwe <PeterHuewe@gmx.de>
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Fixed some coding style issues reported by checkpatch.
Signed-off-by: Bruno E O Meneguele <bmeneguele@gmail.com>
[phuewe: ported to latest code]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
TPM 2.0 devices are separated by adding a field 'flags' to struct
tpm_chip and defining a flag TPM_CHIP_FLAG_TPM2 for tagging them.
This patch adds the following internal functions:
- tpm2_get_random()
- tpm2_get_tpm_pt()
- tpm2_pcr_extend()
- tpm2_pcr_read()
- tpm2_startup()
Additionally, the following exported functions are implemented for
implementing TPM 2.0 device drivers:
- tpm2_do_selftest()
- tpm2_calc_ordinal_durations()
- tpm2_gen_interrupt()
The existing functions that are exported for the use for existing
subsystems have been changed to check the flags field in struct
tpm_chip and use appropriate TPM 2.0 counterpart if
TPM_CHIP_FLAG_TPM2 is est.
The code for tpm2_calc_ordinal_duration() and tpm2_startup() were
originally written by Will Arthur.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Signed-off-by: Will Arthur <will.c.arthur@intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
[phuewe: Fixed copy paste error * 2]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Added own device class for TPM. Uses MISC_MAJOR:TPM_MINOR for the
first character device in order to retain backwards compatibility.
Added tpm_dev_release() back attached to the character device.
I've been running this code now for a while on my laptop (Lenovo
T430S) TrouSerS works perfectly without modifications. I don't
believe it breaks anything significantly.
The sysfs attributes that have been placed under the wrong place
and are against sysfs-rules.txt should be probably left to
stagnate under platform device directory and start defining
new sysfs attributes to the char device directory.
Guidelines for future TPM sysfs attributes should be probably
along the lines of
- Single flat set of mandatory sysfs attributes. For example,
current PPI interface is way way too rich when you only want
to use it to clear and activate the TPM.
- Define sysfs attribute if and only if there's no way to get
the value from ring-3. No attributes for TPM properties. It's
just unnecessary maintenance hurdle that we don't want.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Rename chip->dev to chip->pdev to make it explicit that this not the
character device but actually represents the platform device.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Traversal of the ACPI device tree was not done right. PPI interface
should be looked up only from the ACPI device that is the platform
device for the TPM. This could cause problems with systems with
two TPM chips such as 4th gen Intel systems.
In addition, added the missing license and copyright platter to
the tpm_ppi.c.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
tpm_register_hardware() and tpm_remove_hardware() are called often
before initializing the device. The problem is that the device might
not be fully initialized when it comes visible to the user space.
This patch resolves the issue by diving initialization into two
parts:
- tpmm_chip_alloc() creates struct tpm_chip.
- tpm_chip_register() sets up the character device and sysfs
attributes.
The framework takes care of freeing struct tpm_chip by using the devres
API. The broken release callback has been wiped. ACPI drivers do not
ever get this callback.
Regards to Jason Gunthorpe for carefully reviewing this part of the
code.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
[phuewe: update to upstream changes]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Merged transmit_cmd() functions in tpm-interface.c and tpm-sysfs.c.
Added "tpm_" prefix for consistency sake. Changed cmd parameter as
opaque. This enables to use separate command structures for TPM1
and TPM2 commands in future. Loose coupling works fine here.
Signed-off-by: Jarkko Sakkinen <jarkko.sakkinen@linux.intel.com>
Reviewed-by: Jasob Gunthorpe <jason.gunthorpe@obsidianresearch.com>
Reviewed-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Tested-by: Scot Doyle <lkml14@scotdoyle.com>
Tested-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This consolidates everything that is only used within tpm-dev.c
into tpm-dev.c and out of the publicly visible struct tpm_chip.
The per-file allocation lays the ground work for someday fixing the
strange forced O_EXCL behaviour of the current code.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This builds on the last commit to use the ops structure in the core
and reduce the size of tpm_vendor_specific.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
This replaces the static initialization of a tpm_vendor_specific
structure in the drivers with the standard Linux idiom of providing
a const structure of function pointers.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe: did apply manually due to commit
191ffc6bde3 tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The tpm core now sets up and controls all sysfs attributes, instead
of having each driver have a unique take on it.
All drivers now now have a uniform set of attributes, and no sysfs
related entry points are exported from the tpm core module.
This also uses the new method used to declare sysfs attributes
with DEVICE_ATTR_RO and 'struct attribute *'
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
[phuewe: had to apply the tpm_i2c_atmel part manually due to commit
191ffc6bde3fc tpm/tpm_i2c_atmel: fix coccinelle warnings]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
CLASS-sysfs.c is a common idiom for linux subsystems.
This is the first step to pulling all the sysfs support code from
the drivers into tpm-sysfs. This is a plain text copy from tpm-interface
with support changes to make it compile.
_tpm_pcr_read is made non-static and is called tpm_pcr_read_dev.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
CLASS-dev.c is a common idiom for Linux subsystems
This pulls all the code related to the miscdev into tpm-dev.c and makes it
static. The identical file_operation structs in the drivers are purged and the
tpm common code unconditionally creates the miscdev.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Ashley Lai <adlai@linux.vnet.ibm.com>
[phuewe:
tpm_dev_release is now used only in this file, thus the EXPORT_SYMBOL
can be dropped and the function be marked as static.
It has no other in-kernel users]
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
The version of the TPM should not depend on the bus it is connected
through. 1.1, 1.2 and soon 2.0 TPMS will be all be able to use the
same bus interfaces.
Make tpm_show_caps try the 1.2 capability first. If that fails then
fall back to the 1.1 capability. This effectively auto-detects what
interface the TPM supports at run-time.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Just put the memory directly in the chip structure, rather than
in a 2nd dedicated kmalloc.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Joel Schopp <jschopp@linux.vnet.ibm.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Acked-by: Ashley Lai <adlai@linux.vnet.ibm.com>
The 8119807 commit reintroduced a regression
(error: __ksymtab_tpm_dev_release causes a section type conflict) that was fixed by commit
cbb2ed4.
Fix it for good by adding the prototype to tpm.h so sparse doesn't
complain about it anymore.
Reported-by: Tony Camuso <tcamuso@redhat.com>
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
IMA requires access to TPM_DIGEST_SIZE definition. This patch
moves the definition to <linux/tpm.h>.
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
If the TPM has already been sent a SaveState command before the driver
is loaded it may have problems sending that same command again later.
This issue is seen with the Chromebook Pixel due to a firmware bug in
the legacy mode boot path which is sending the SaveState command
before booting the kernel. More information is available at
http://crbug.com/203524
This change introduces a retry of the SaveState command in the suspend
path in order to work around this issue. A future firmware update
should fix this but this is also a trivial workaround in the driver
that has no effect on systems that do not show this problem.
When this does happen the TPM responds with a non-fatal TPM_RETRY code
that is defined in the specification:
The TPM is too busy to respond to the command immediately, but the
command could be resubmitted at a later time. The TPM MAY return
TPM_RETRY for any command at any time.
It can take several seconds before the TPM will respond again. I
measured a typical time between 3 and 4 seconds and the timeout is set
at a safe 5 seconds.
It is also possible to reproduce this with commands via /dev/tpm0.
The bug linked above has a python script attached which can be used to
test for this problem. I tested a variety of TPMs from Infineon,
Nuvoton, Atmel, and STMicro but was only able to reproduce this with
LPC and I2C TPMs from Infineon.
The TPM specification only loosely defines this behavior:
TPM Main Level 2 Part 3 v1.2 r116, section 3.3. TPM_SaveState:
The TPM MAY declare all preserved values invalid in response to any
command other than TPM_Init.
TCG PC Client BIOS Spec 1.21 section 8.3.1.
After issuing a TPM_SaveState command, the OS SHOULD NOT issue TPM
commands before transitioning to S3 without issuing another
TPM_SaveState command.
TCG PC Client TIS 1.21, section 4. Power Management:
The TPM_SaveState command allows a Static OS to indicate to the TPM
that the platform may enter a low power state where the TPM will be
required to enter into the D3 power state. The use of the term "may"
is significant in that there is no requirement for the platform to
actually enter the low power state after sending the TPM_SaveState
command. The software may, in fact, send subsequent commands after
sending the TPM_SaveState command.
Change-Id: I52b41e826412688e5b6c8ddd3bb16409939704e9
Signed-off-by: Duncan Laurie <dlaurie@chromium.org>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Support cancellation of TPM commands when driver is used in interrupt
mode.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
On one of my machines the cancellation of TPM commands does not work.
The reason is that by writing into sysfs 'cancel' the tpm_tis_ready
call causes the status flag TPM_STS_VALID to be set in the statusregister.
However, the TIS driver seems to wait for TPM_STS_COMMAND_READY.
Once a 2nd time sysfs 'cancel' is written to, the TPM_STS_COMMAND_READY flag
also gets set, resulting in TPM_STS_VALID|TPM_STS_COMMAND_READY to be
read from the status register.
This patch now converts req_canceled into a function to enable more complex
comparisons against possible cancellation status codes.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
"data" was too generic a name for what's being used as a generic
private pointer by vendor-specific code. Rename it to "priv" and provide
a #define for users.
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This seems to be preferred these days.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Reviewed-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The TPM will respond to TPM_GET_CAP with TPM_ERR_INVALID_POSTINIT if
TPM_STARTUP has not been issued. Detect this and automatically
issue TPM_STARTUP.
This is for embedded applications where the kernel is the first thing
to touch the TPM.
Signed-off-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Peter Huewe <peter.huewe@infineon.com>
Reviewed-by: Peter Huewe <peter.huewe@infineon.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch try to fix the S3 regression https://lkml.org/lkml/2012/10/5/433,
which includes below line:
[ 1554.684638] sysfs: cannot create duplicate filename '/devices/pnp0/00:0c/ppi'
The root cause is that ppi sysfs teardown code is MIA, so while S3 resume,
the ppi kobject will be created again upon existing one.
To make the tear down code simple, change the ppi subfolder creation from
using kobject_create_and_add to just using a named ppi attribute_group. Then
ppi sysfs teardown could be done with a simple sysfs_remove_group call.
Adjusted the name & return type for ppi sysfs init function.
Reported-by: Ben Guthro <ben@guthro.net>
Signed-off-by: Gang Wei <gang.wei@intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
The Physical Presence Interface enables the OS and the BIOS to cooperate and
provides a simple and straightforward platform user experience for
administering the TPM without sacrificing security.
V2: separate the patch out in a separate source file,
add #ifdef CONFIG_ACPI so it compiles out on ppc,
use standard error instead of ACPI error as return code of show/store fns.
V3: move #ifdef CONFIG_ACPI from .c file to .h file.
V4: move tpm_ppi code from tpm module to tpm_bios module.
V5: modify sys_add_ppi() so that ppi_attr_grp doesn't need to be exported
Signed-off-by: Xiaoyan Zhang <xiaoyan.zhang@intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch retrieves the event log data from the device tree
during file open. The event log data will then displayed through
securityfs.
Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
This patch adds a new device driver to support IBM virtual TPM
(vTPM) for PPC64. IBM vTPM is supported through the adjunct
partition with firmware release 740 or higher. With vTPM
support, each lpar is able to have its own vTPM without the
physical TPM hardware.
This driver provides TPM functionalities by communicating with
the vTPM adjunct partition through Hypervisor calls (Hcalls)
and Command/Response Queue (CRQ) commands.
Signed-off-by: Ashley Lai <adlai@us.ibm.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Move the tpm_get_random api from the trusted keys code into the TPM
device driver itself so that other callers can make use of it. Also,
change the api slightly so that the number of bytes read is returned in
the call, since the TPM command can potentially return fewer bytes than
requested.
Acked-by: David Safford <safford@linux.vnet.ibm.com>
Reviewed-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: Kent Yoder <key@linux.vnet.ibm.com>
Detect iTPMs through the vendor ID on the hardware interface and only
probe the device if the manufacturer is found to be Intel. This
obsoletes a previously added delay necessary for some TPMs but not iTPMs.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch fixes an (ACPI S3) suspend regression introduced in commit
68d6e6713f ("tpm: Introduce function to poll for result of self test")
and occurring with an Infineon TPM and tpm_tis and tpm_infineon drivers
active.
The suspend problem occurred if the TPM was disabled and/or deactivated
and therefore the TPM_PCRRead checking the result of the (asynchronous)
self test returned an error code which then caused the tpm_tis driver to
become inactive and this then seemed to have negatively influenced the
suspend support by the tpm_infineon driver... Besides that the tpm_tis
drive may stay active even if the TPM is disabled and/or deactivated.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's incorrect to assume that buffers returned by the TPM
10 bytes long are always error reports. This patches
parses the error field in its header instead. The error report
is now being printed using dev_err() instead of dev_dbg(), making
it easier for users to provide more detailed bug reports.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Moved wait_for_stat to tpm.c so that other drivers can use it.
Also renamed it to avoid future namespace conflicts.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This patch introduces a function that runs the TPM_ContinueSelfTest()
function and then polls the TPM to check whether it finished the selftest
and can receive new commands.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
This patch fixes several aspects of the probing for interrupts.
This patch reads the TPM's timeouts before probing for the interrupts. The
tpm_get_timeouts() function is invoked in polling mode and gets the proper
timeouts from the TPM so that we don't need to fall back to 2 minutes timeouts
for short duration commands while the interrupt probing is happening.
This patch introduces a variable probed_irq into the vendor structure that gets
the irq number if an interrupt is received while the the tpm_gen_interrupt()
function is run in polling mode during interrupt probing. Previously some
parts of tpm_gen_interrupt() were run in polling mode, then the irq variable
was set in the interrupt handler when an interrupt was received and execution
of tpm_gen_interrupt() ended up switching over to interrupt mode.
tpm_gen_interrupt() execution ended up on an event queue where it eventually
timed out since the probing handler doesn't wake any queues.
Before calling into free_irq() clear all interrupt flags that may have
been set by the TPM. The reason is that free_irq() will call into the probing
interrupt handler and may otherwise fool us into thinking that a real interrupt
happened (because we see the flags as being set) while the TPM's interrupt line
is not even connected to anything on the motherboard. This solves a problem
on one machine I did testing on (Thinkpad T60).
If a TPM claims to use a specifc interrupt, the probing is done as well
to verify that the interrupt is actually working. If a TPM indicates
that it does not use a specific interrupt (returns '0'), probe all interrupts
from 3 to 15.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Display the TPM's interface timeouts in a 'timeouts' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Display the TPM's command timeouts in a 'durations' sysfs entry. Display
the entries as having been adjusted when they were scaled due to their values
being reported in milliseconds rather than microseconds.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
This reverts commit 9b29050f8f.
It has caused hibernate regressions, for example Juri Sladby's report:
"I'm unable to hibernate 2.6.37.1 unless I rmmod tpm_tis:
[10974.074587] Suspending console(s) (use no_console_suspend to debug)
[10974.103073] tpm_tis 00:0c: Operation Timed out
[10974.103089] legacy_suspend(): pnp_bus_suspend+0x0/0xa0 returns -62
[10974.103095] PM: Device 00:0c failed to freeze: error -62"
and Rafael points out that some of the new conditionals in that commit
seem to make no sense. This commit needs more work and testing, let's
revert it for now.
Reported-by: Norbert Preining <preining@logic.at>
Reported-and-requested-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Stefan Berger <stefanb@linux.vnet.ibm.com>
Cc: Guillaume Chazarain <guichaz@gmail.com>
Cc: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current TPM TIS driver in git discards the timeout values returned
from the TPM. The check of the response packet needs to consider that
the return_code field is 0 on success and the size of the expected
packet is equivalent to the header size + u32 length indicator for the
TPM_GetCapability() result + 3 timeout indicators of type u32.
I am also adding a sysfs entry 'timeouts' showing the timeouts that are
being used.
Signed-off-by: Stefan Berger <stefanb@linux.vnet.ibm.com>
Tested-by: Guillaume Chazarain <guichaz@gmail.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
For readability, define a tpm_chip_put() wrapper to call module_put().
Replace existing module_put() calls with the wrapper.
(Change based on trusted/encrypted patchset review by David Howells.)
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: David Safford <safford@watson.ibm.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Serge E. Hallyn <serge.hallyn@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch adds a missing element of the ReadPubEK command output,
that prevents future overflow of this buffer when copying the
TPM output result into it.
Prevents a kernel panic in case the user tries to read the
pubek from sysfs.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch adds internal kernel support for:
- reading/extending a pcr value
- looking up the tpm_chip for a given chip number
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: Mimi Zohar <zohar@us.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
According to Dave Hansen's comments on the tpm_show_*, some of these functions
present a pattern when allocating data[] memory space and also when setting its
content. A new function was created so that this pattern could be consolidated.
Also, replaced the data[] command vectors and its indexes by meaningful structures
as pointed out by Matt Helsley too.
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Signed-off-by: James Morris <jmorris@namei.org>
devices, so we implemented the .remove function for pnp ones. Since it's
code is very similar to the one inside tpm_dev_release, we've created a
helper function tpm_dev_vendor_release, which is called by both.
Signed-off-by: Mimi Zohar <zohar@linux.vnet.ibm.com>
Signed-off-by: Rajiv Andrade <srajiv@linux.vnet.ibm.com>
Cc: "Serge E. Hallyn" <serue@us.ibm.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Morris <jmorris@namei.org>
Jarkko Sakkinen