MTC packets provide finer grain timestamp information than TSC packets.
MTC packets record time using the hardware crystal clock (CTC) which is
related to TSC packets using a TMA packet.
This patch just adds decoder support.
Support for a default value and validation of values is provided by a
later patch. Also documentation is updated in a separate patch.
For details refer to the June 2015 or later Intel 64 and IA-32
Architectures SDM Chapter 36 Intel Processor Trace.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-21-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Record additional information in the AUXTRACE_INFO event in preparation
for decoding MTC and CYC packets. Pass the information to the decoder.
The AUXTRACE_INFO record can be extended by using the size to indicate
the presence of new members.
The additional information includes PMU config bit positions and the TSC
to CTC (hardware crystal clock) ratio needed to decode MTC packets.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-20-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
New features have been added to Intel PT which include a number of new
packet definitions.
This patch adds packet definitions for new packets: TMA, MTC, CYC, VMCS,
TRACESTOP and MNT. Also another bit in PIP is defined.
This patch only adds support for the definitions. Later patches add
support for decoding TMA, MTC, CYC and TRACESTOP which is where those
packets are explained.
VMCS and the newly defined bit in PIP are used with virtualization which
is not supported yet. MNT is a maintenance packet which the decoder
should ignore.
For details, refer to the June 2015 or later Intel 64 and IA-32
Architectures SDM Chapter 36 Intel Processor Trace.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-19-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The PSB packet is a synchronization packet that provides a starting
point for decoding or recovery from errors.
This patch adds support for a new Intel PT feature that allows the
frequency of PSB packets to be specified.
Support for this feature is indicated by
/sys/bus/event_source/devices/intel_pt/caps/psb_cyc which contains "1"
if the feature is supported and "0" otherwise.
The PSB period can be specified as a PMU config term e.g. perf record -e
intel_pt/psb_period=2/u sleep 1
The default value is 3 or the nearest lower value that is supported. 0
is always supported.
Valid values are given by:
/sys/bus/event_source/devices/intel_pt/caps/psb_periods
which contains a hexadecimal value, the bits of which represent valid
values e.g. bit 2 set means value 2 is valid.
The value is converted to the approximate number of trace bytes between
PSB packets as:
2 ^ (value + 11)
e.g. value 3 means 16KiB bytes between PSBs
If an invalid value is entered, the error message will give a list of
valid values e.g.
$ perf record -e intel_pt/psb_period=15/u uname
Invalid psb_period for intel_pt. Valid values are: 0-5
tools/perf/Documentation/intel-pt.txt is updated in a later patch as
there are a number of new features being added.
For more information about PSB periods refer to the Intel 64 and IA-32
Architectures SDM Chapter 36 Intel Processor Trace from June 2015 or
later.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-18-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The period on synthesized 'instructions' samples was being set to a
fixed value, whereas the correct value is the number of instructions
since the last sample, which is a value that the decoder can provide.
So do it that way.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-14-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We were depending on the next screen operation after a flush() being
one that would redraw the whole screen so that the progress bar would
be overwritten, when that didn't happen a screen artifact of, say, a
error dialog window would be overlaid on top of the progress bar, fix
it by calling ui_browser__finish(), that now has a TUI implementation.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-el0fyw6duemnx62lydjzhs8c@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So that we can erase the progress bar after we're done with it, avoiding
things like:
-------------------------------------------------------------------
┌─Error:──────────────────────────────────────────────────────┐
│Can't annotate unmapped_area_topdown: │
│ │
│No vmlinux file with build id a826726b5ddacfab1f0bade868f1a79│
│was found in the path. │
│ │
│Note that annotation using /proc/kcore requires CAP_SYS_RAWIO│
┌Processin│ │──┐
│ │Please use: │ │
└─────────│ │──┘
│ perf buildid-cache -vu vmlinux │
│ │
│or: │
│ │
│ --vmlinux vmlinux │
│ │
│ │
│Press any key... │
└─────────────────────────────────────────────────────────────┘
Can't annotate unmapped_area_topdown:
-------------------------------------------------------------------
I.e. that finished progress bar behind the error window. It is not a
problem when we end up redrawing the whole screen, but its ugly when
we present such error windows, provide a TUI method so that code like
the above may avoid this situation, as will be done with the annotation
code in the next cset.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-qvktnojzwwe37pweging058t@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The 'annotate' tool does some filtering in the entries in a DSO but
forgot to reset the cache done in dso__find_symbol(), cauxing a SEGV:
[root@zoo ~]# perf annotate netlink_poll
perf: Segmentation fault
-------- backtrace --------
perf[0x526ceb]
/lib64/libc.so.6(+0x34960)[0x7faedfbe0960]
perf(rb_erase+0x223)[0x499d63]
perf[0x4213e9]
perf[0x4bc123]
perf[0x4bc621]
perf[0x4bf26b]
perf[0x4bc855]
perf(perf_session__process_events+0x340)[0x4bddc0]
perf(cmd_annotate+0x6bb)[0x421b5b]
perf[0x479063]
perf(main+0x60a)[0x42098a]
/lib64/libc.so.6(__libc_start_main+0xf0)[0x7faedfbcbfe0]
perf[0x420aa9]
[0x0]
[root@zoo ~]#
Fix it by reseting the find cache when removing symbols.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Fixes: b685ac22b4 ("perf symbols: Add front end cache for DSO symbol lookup")
Link: http://lkml.kernel.org/n/tip-b2y9x46y0t8yem1ive41zqyp@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix some include paths and add missing inat_types.h.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/55D77696.60102@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
A problem can occur in a statically linked perf when vmlinux can be found:
# perf probe --add sys_epoll_pwait
probe-definition(0): sys_epoll_pwait
symbol:sys_epoll_pwait file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Looking at the vmlinux_path (7 entries long)
Using /lib/modules/4.2.0-rc1+/build/vmlinux for symbols
Open Debuginfo file: /lib/modules/4.2.0-rc1+/build/vmlinux
Try to find probe point from debuginfo.
Symbol sys_epoll_pwait address found : ffffffff8122bd40
Matched function: SyS_epoll_pwait
Failed to get call frame on 0xffffffff8122bd40
An error occurred in debuginfo analysis (-2).
Error: Failed to add events. Reason: No such file or directory (Code: -2)
The reason is caused by libdw that, if libdw is statically linked, it
can't load libebl_{arch}.so reliable.
In this case it is still possible to get the address from
/proc/kalksyms. However, perf tries that only when libdw returns
-EBADF.
This patch gives it another chance to utilize symbol table, even if
libdw returns an error code other than -EBADF.
After applying this patch:
# perf probe -nv --add sys_epoll_pwait
probe-definition(0): sys_epoll_pwait
symbol:sys_epoll_pwait file:(null) line:0 offset:0 return:0 lazy:(null)
0 arguments
Looking at the vmlinux_path (7 entries long)
Using /lib/modules/4.2.0-rc1+/build/vmlinux for symbols
Open Debuginfo file: /lib/modules/4.2.0-rc1+/build/vmlinux
Try to find probe point from debuginfo.
Symbol sys_epoll_pwait address found : ffffffff8122bd40
Matched function: SyS_epoll_pwait
Failed to get call frame on 0xffffffff8122bd40
An error occurred in debuginfo analysis (-2).
Trying to use symbols.
Opening /sys/kernel/debug/tracing/kprobe_events write=1
Added new event:
Writing event: p:probe/sys_epoll_pwait _text+2276672
probe:sys_epoll_pwait (on sys_epoll_pwait)
You can now use it in all perf tools, such as:
perf record -e probe:sys_epoll_pwait -aR sleep 1
Although libdw returns an error (Failed to get call frame), perf tries
symbol table and finally gets correct address.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1440151770-129878-2-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Map clone was written before we introduced reference counts for
maps and dsos, so all that was needed was just a copy and then we
would insert it into the new map_groups instance.
Fix it by, after copying, initializing the map->refcnt, grabbing
a struct dso refcount and resetting pointers that may be used
to determine if a map, when deleted, is in a rb_tree.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-pd4mr80o5b9gvk50iineacec@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a script to produce a call-graph from data exported to a postgresql
database and derived from a processor trace event like intel_pt or intel_bts.
Refer to comments in the scripts call-graph-from-postgresql.py and
export-to-postgresql.py for more details on how to set up the environment,
install the required packages, etc.
Committer note:
From the scripts, for convenience while reading 'git log':
An example of using this script with Intel PT:
$ perf record -e intel_pt//u ls
$ perf script -s ~/libexec/perf-core/scripts/python/export-to-postgresql.py pt_example branches calls
2015-05-29 12:49:23.464364 Creating database...
2015-05-29 12:49:26.281717 Writing to intermediate files...
2015-05-29 12:49:27.190383 Copying to database...
2015-05-29 12:49:28.140451 Removing intermediate files...
2015-05-29 12:49:28.147451 Adding primary keys
2015-05-29 12:49:28.655683 Adding foreign keys
2015-05-29 12:49:29.365350 Done
$ python tools/perf/scripts/python/call-graph-from-postgresql.py pt_example
# The result is a GUI window with a tree representing a context-sensitive
# call-graph. Expanding a couple of levels of the tree and adjusting column
# widths to suit will display something like:
Call Graph: pt_example
Call Path |Object |Count|Time(ns)|Time(%)|Branch Count|Branch Count(%)
v- ls
v- 2638:2638
v- _start ld-2.19.so 1 10074071 100.0 211135 100.0
|- unknown unknown 1 13198 0.1 1 0.0
>- _dl_start ld-2.19.so 1 1400980 13.9 19637 9.3
>- _d_linit_internal ld-2.19.so 1 448152 4.4 11094 5.3
v-__libc_start_main@plt ls 1 8211741 81.5 180397 85.4
>- _dl_fixup ld-2.19.so 1 7607 0.1 108 0.1
>- __cxa_atexit libc-2.19.so 1 11737 0.1 10 0.0
>- __libc_csu_init ls 1 10354 0.1 10 0.0
|- _setjmp libc-2.19.so 1 0 0.0 4 0.0
v- main ls 1 8182043 99.6 180254 99.9
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-11-git-send-email-adrian.hunter@intel.com
[ Added 'python-pyside qt-postgresql' to the yum cmdline installing required packages ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf script, report and inject all have the same itrace options. Put
them into an asciidoc include file.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-10-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Events that don't sample the timestamp have a timestamp value of -1.
Intel PT processing wasn't taking that into account.
This is particularly noticeable with Intel BTS because timestamps are
not requested by default.
Then, if the conversion of -1 to TSC results in a small number, the
processing is unaffected.
However if the conversion results in a big number, then the data is
processed prematurely before relevant sideband data like mmap events,
which in turn results in samples with unknown dsos.
Commiter note:
Since BTS wasn't upstream, I split the patch to fold the BTS part with
the patch introducing it, to avoid having this bug in the commit
history. PT was already upstream, so this patch contains that part.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1440060692-5585-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The "/proc/kcore requires CAP_SYS_RAWIO" message comes up all the time
for 'perf script' if vmlinux is not found and the user isn't root, even
when the kernel is not being traced and even though the message is only
really relevant for annotation.
Change it to pr_debug and instead put a note in the message displayed if
annotation is not possible.
Also, the file being accessed might not be /proc/kcore. Tools can be
directed to a different location using the --kallsyms option in which
case kcore is expected to be in the same directory. Adjust the message
so it is not misleading in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Li Zhang <zhlcindy@linux.vnet.ibm.com>
Cc: Sukadev Bhattiprolu <sukadev@linux.vnet.ibm.com>
Link: http://lkml.kernel.org/r/1440065260-8802-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Patch "perf script: Don't assume evsel position of tracking events"
changed 'perf script' to use 'perf_evlist__id2evsel()'. That results
in a segfault if there is more than 1 event and there are
synthesized mmap events e.g.
$ perf record -e cycles,instructions -p$$ sleep 1
$ perf script --show-mmap-events
Segmentation fault (core dumped)
That happens because these synthesized events have an 'id' of zero
which does not match any 'evsel'.
Currently, these synthesized events use the sample type of the first
evsel.
Change 'perf_evlist__id2evsel()' to reflect that which also makes
it consistent with 'perf_evlist__event2evsel()'.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 06b234ec26 ("perf script: Don't assume evsel position of tracking events")
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1440059205-1765-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
It was just freezing instead of informing about the SEGV, fix it and
also print a backtrace, just like in the TUI mode and in 'perf trace'.
Tested by provoking a NULL deref when pressing 'z':
0.31% libc-2.20.so [.] malloc_consolidate
0.31% ld-2.20.so [.] _dl_relocate_object
0.28% cc1 [.] ht_lookup
0.28% cc1 [.] ira_init_register_move_cost
perf: Segmentation fault
Obtained 7 stack frames.
perf(dump_stack+0x32) [0x4d69f2]
perf(sighandler_dump_stack+0x29) [0x4d6a89]
/lib64/libc.so.6(+0x34960) [0x7f5064333960]
perf() [0x438790]
/lib64/libpthread.so.0(+0x752a) [0x7f50663dd52a]
/lib64/libc.so.6(clone+0x6d) [0x7f50643ff22d]
#
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-pewrpzqd29rgmhu2wkk7fhww@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
After recording, 'perf record' post-processes the data to determine
which buildids are needed.
That processing must process the data in time order, if possible,
because otherwise dependent events, like forks and mmaps, will not make
sense.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1439994561-27436-4-git-send-email-adrian.hunter@intel.com
[ Moved the sample_id_add to after trying to open the events, use pr_warning ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When processing a fork event, the tools lookup the parent thread by its
tid. In a couple of cases, it is possible for that thread to have the
wrong pid.
That can happen if the data is being processed out of order, or if the
(fork) event that would have removed the erroneous thread was lost.
Assume the latter case, print a dump message, remove the erroneous
thread, create a new one with the correct pid, and keep going.
Reported-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Link: http://lkml.kernel.org/r/1439994561-27436-3-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Attempting to clone map groups onto themselves will deadlock.
It only happens because of other bugs, but the code should protect
itself anyway.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1439994561-27436-2-git-send-email-adrian.hunter@intel.com
[ Use pr_debug() instead of dump_fprintf() ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add support for Intel Processor Trace.
Intel PT support fits within the new auxtrace infrastructure. Recording
is supporting by identifying the Intel PT PMU, parsing options and
setting up events.
Decoding is supported by queuing up trace data by cpu or thread and then
decoding synchronously delivering synthesized event samples into the
session processing for tools to consume.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-7-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add support for decoding an Intel Processor Trace.
Intel PT trace data must be 'decoded' which involves walking the object
code and matching the trace data packets.
The decoder requests a buffer of binary data via a get_trace()
call-back, which it decodes using instruction information which it gets
via another call-back walk_insn().
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-6-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add a facility to log Intel Processor Trace decoding. The log is
intended for debugging purposes only.
The log file name is "intel_pt.log" and is opened in the current
directory. The log contains a record of all packets and instructions
decoded and can get very large (10 MB would be a small one).
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-5-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add support for decoding instructions for Intel Processor Trace. The
kernel x86 instruction decoder is copied for this.
This essentially provides intel_pt_get_insn() which takes a binary
buffer, uses the kernel's x86 instruction decoder to get details of the
instruction and then categorizes it for consumption by an Intel PT
decoder.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1439450095-30122-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add support for decoding Intel Processor Trace packets.
This essentially provides intel_pt_get_packet() which takes a buffer of
binary data and returns the decoded packet.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-3-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add the Intel Processor Trace type constant PERF_AUXTRACE_INTEL_PT.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-2-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Older kernels attempt to prelink vdso to its virtual address. To permit
annotation using objdump, the map__rip_2objdump() calculation must
result in that same address which we can infer from the start and offset
of the text section.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Will Deacon <will.deacon@arm.com>
Link: http://lkml.kernel.org/r/1439556606-11297-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Fix the following 32-bit compilation errors:
util/annotate.c: In function ‘addr_map_symbol__account_cycles’:
util/annotate.c:643:3: error: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 4 has type ‘u64’ [-Werror=format=]
pr_debug2("BB with bad start: addr %lx start %lx sym %lx saddr %lx\n",
^
util/annotate.c:643:3: error: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 5 has type ‘u64’ [-Werror=format=]
util/annotate.c:643:3: error: format ‘%lx’ expects argument of type ‘long unsigned int’, but argument 6 has type ‘u64’ [-Werror=format=]
These were introduced by the patch:
"perf report: Add infrastructure for a cycles histogram"
Also change the 'saddr' variable from 'unsigned long' to 'u64'
noting that theoretically we could be processing data captured
on a 64-bit machine but processing it on a 32-bit machine.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Fixes: d4957633bf ("perf report: Add infrastructure for a cycles histogram")
Link: http://lkml.kernel.org/r/1439536294-18241-1-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Milian Wolff reported non functional DWARF unwind under perf script. The
reason is that perf script does not properly configure
callchain_param.record_mode, which is needed by unwind code.
Stealing the code from report and leaving the place for more
initialization code in a hope we could merge it with
report__setup_sample_type one day.
Reported-by: Milian Wolff <mail@milianw.de>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Milian Wolff <milian.wolff@kdab.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/20150813071724.GA21322@krava.brq.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We were storing the vfs_getname payload (i.e. ptr->string) into
the trace wide storage area (struct trace), so that we could use the
last payload when setting up the fd->pathname per thread tables, oops,
not a good idea for multi cpu tracing sessions...
Fix it by moving it to the per thread area (struct thread_trace).
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-3j05ttqyaem7kh7oubvr1keo@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The commit 75186a9b09 (perf probe: Fix to show lines of sys_ functions
correctly) introduced a bug by a missed brace around if block. This
fixes to add it.
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Fixes: 75186a9b09 ("perf probe: Fix to show lines of sys_ functions correctly")
Link: http://lkml.kernel.org/r/20150812215541.9088.62425.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The Fedora 22 version of libdw requires a couple of extra libraries to
link. With a dynamic link the dependencies are pulled in automatically,
but this doesn't work for static linking. Add the needed libraries
explicitely to the feature probe and the Makefile.
v2: Explicitly check for static linking and only add the dependencies
when -static is set. This is to avoid regressions on Arnaldo's system.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/1439419717-20601-1-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add tests in tests/parse-events.c to check call-graph and time option.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1439289050-40510-4-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
"perf probe --lines sys_poll" shows only the first line of sys_poll,
because the SYSCALL_DEFINE macro:
----
SYSCALL_DEFINE*(foo,...)
{
body;
}
----
is expanded as below (on debuginfo)
----
static inline int SYSC_foo(...)
{
body;
}
int SyS_foo(...) <- is an alias of sys_foo.
{
return SYSC_foo(...);
}
----
So, "perf probe --lines sys_foo" decodes SyS_foo function and it also skips
inlined functions(SYSC_foo) inside the target function because those functions
are usually defined somewhere else.
To fix this issue, this fix checks whether the inlined function is defined at
the same point of the target function, and if so, it doesn't skip the inline
function.
Reported-by: Arnaldo Carvalho de Melo <acme@kernel.org>
Signed-off-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/20150812012406.11811.94691.stgit@localhost.localdomain
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In addition to <-, that may be repurposed for horizontal scrolling.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-w3rctelxr4yxrjufx7z3fclb@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To remove direct access to libslang functions, with the immediate goal
of implementing horizontal scrolling at the ui_browser level, but also
because we may at some point want to implement ui_browser with other UIs
in addition to the current libslang implementation.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-w0niblabqrkecs4o0eogfy6c@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To remove direct access to libslang functions, with the immediate goal
of implementing horizontal scrolling at the ui_browser level, but also
because we may at some point want to implement ui_browser with other UIs
in addition to the current libslang implementation.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-437ineavoejzou727mr9bxpi@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
But we really should have something like 'strace -yy' here...
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-eyrt1ypfq68u4ljagyk2nj1i@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Handle the SRCLINE_UNKNOWN case correctly when processing "srcfile".
Commiter note:
We can't just free it, as it was't allocated via malloc, its a guard
variable.
Reported-by: Namhyung Kim <namhyung@kernel.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Link: http://lkml.kernel.org/r/20150811133655.GC4524@tassilo.jf.intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This time using 'trinity' to test these:
fchmodat, futimesat, llistxattr, lremovexattr, lstat, mknodat,
mq_unlink, stat and vmsplice.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-a1uqu249nwwh0ixrhm80k4a4@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently perf evlist -F shows the number as if it's always sampling
frequency. But we now support per-event freq/period settings. So it'd
better to show more detailed info whether it's freq or period.
$ perf record -e 'cpu/config=1/,cpu/config=2,period=300000/' sleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.017 MB perf.data ]
$ perf evlist -F
cpu/config=1/: sample_freq=4000
cpu/config=2,period=300000/: sample_period=300000
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1439102724-14079-2-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Now perf can set per-event value of time and (sampling) period. But I
guess most users like me just want to set frequency rather than period.
So add the 'freq' term in the event parser.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1439102724-14079-1-git-send-email-namhyung@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In some cases it's useful to characterize samples by file. This is
useful to get a higher level categorization, for example to map cost to
subsystems.
Add a srcfile sort key to perf report. It builds on top of the existing
srcline support.
Commiter notes:
E.g.:
# perf record -F 10000 usleep 1
[ perf record: Woken up 1 times to write data ]
[ perf record: Captured and wrote 0.016 MB perf.data (13 samples) ]
[root@zoo ~]# perf report -s srcfile --stdio
# Total Lost Samples: 0
#
# Samples: 13 of event 'cycles'
# Event count (approx.): 869878
#
# Overhead Source File
# ........ ...........
60.99% .
20.62% paravirt.h
14.23% rmap.c
4.04% signal.c
0.11% msr.h
#
The first line is collecting all the files for which srcfiles couldn't somehow
get resolved to:
# perf report -s srcfile,dso --stdio
# Total Lost Samples: 0
#
# Samples: 13 of event 'cycles'
# Event count (approx.): 869878
#
# Overhead Source File Shared Object
# ........ ........... ................
40.97% . ld-2.20.so
20.62% paravirt.h [kernel.vmlinux]
20.02% . libc-2.20.so
14.23% rmap.c [kernel.vmlinux]
4.04% signal.c [kernel.vmlinux]
0.11% msr.h [kernel.vmlinux]
#
XXX: Investigate why that is not resolving on Fedora 21, Andi says he hasn't
seen this on Fedora 22.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1438988064-21834-1-git-send-email-andi@firstfloor.org
[ Added column length update, from 0e65bdb3f90f ('perf hists: Update the column width for the "srcline" sort key') ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When we introduce a new sort key, we need to update the
hists__calc_col_len() function accordingly, otherwise the width
will be limited to strlen(header).
We can't update it when obtaining a line value for a column (for
instance, in sort__srcline_cmp()), because we reset it all when doing a
resort (see hists__output_recalc_col_len()), so we need to, from what is
in the hist_entry fields, set each of the column widths.
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Jiri Olsa <jolsa@kernel.org>
Fixes: 409a8be615 ("perf tools: Add sort by src line/number")
Link: http://lkml.kernel.org/n/tip-jgbe0yx8v1gs89cslr93pvz2@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The iter_add_next_cumulative_entry() function calls hist_entry__cmp(),
which may want to access the hists where this hist_entry is stored,
initialize it to let that happen and avoid segfaults.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-iqg98sfn4fvwcxp0pdvqauie@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We need to unset 'perf_event_attr::freq' bit (default 1) when
'period' term is specified within event definition like:
-e 'cpu/cpu-cycles,call-graph=fp,time,period=100000'
otherwise it will handle the period value as frequency
(and fail if it crossed the maximum allowed frequency value).
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/20150808171210.GC17040@krava.brq.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
For perf report/script srcline currently only the base file name of the
source file is printed. This is a good default because it usually fits
on the screen.
But in some cases we want to know the full file name, for example to
aggregate hits per file.
In the later case we need more than the base file name to resolve file
naming collisions: for example the kernel source has ~70 files named
"core.c"
It's also useful as input to post processing tools which want to point
to the right file.
Add a flag to allow full file name output.
Add an option to perf report/script to enable this option.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1438986245-15191-1-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Move callchain option parse related code to util.c, to avoid dragging
more object files into the python binding.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1438890294-33409-1-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Moving 'struct perf_counts' and associated functions into separate
object, so we could remove stat.c object dependency from python build.
It makes the python code to build properly, because it fails to load due
to missing stat-shadow.c object dependency if some patches from Kan
Liang are applied.
So apply this one, then Kan's.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/20150807105103.GB8624@krava.brq.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Previous patches introduce llvm__compile_bpf() to compile source file to
eBPF object. This patch adds testcase to test it. It also tests libbpf
by opening generated object after applying next patch which introduces
HAVE_LIBBPF_SUPPORT option.
Since llvm__compile_bpf() prints long messages which users who don't
explicitly test llvm doesn't care, this patch set verbose to -1 to
suppress all debug, warning and error message, and hint user use 'perf
test -v' to see the full output.
For the same reason, if clang is not found in PATH and there's no [llvm]
section in .perfconfig, skip this test.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/n/1436445342-1402-17-git-send-email-wangnan0@huawei.com
[ Add tools/lib/bpf/ to tools/perf/MANIFEST, so that the tarball targets build ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To help user find correct kernel include options, this patch extracts
them from kbuild system by an embedded script kinc_fetch_script, which
creates a temporary directory, generates Makefile and an empty dummy.o
then use the Makefile to fetch $(NOSTDINC_FLAGS), $(LINUXINCLUDE) and
$(EXTRA_CFLAGS) options. The result is passed to compiler script using
'KERNEL_INC_OPTIONS' environment variable.
Because options from kbuild contains relative path like
'Iinclude/generated/uapi', the work directory must be changed. This is
done by previous patch.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1436445342-1402-16-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch detects kernel build directory by checking the existence of
include/generated/autoconf.h.
clang working directory is changed to kbuild directory if it is found,
to help user use relative include path. Following patch will detect
kernel include directory, which contains relative include patch so this
workdir changing is needed.
Users are allowed to set 'kbuild-dir = ""' manually to disable this
checking.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/n/tip-owyfwfbemrjn0tlj6tgk2nf5@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This is the core patch for supporting eBPF on-the-fly compiling, does
the following work:
1. Search clang compiler using search_program().
2. Run command template defined in llvm-bpf-cmd-template option in
[llvm] config section using read_from_pipe(). Patch of clang and
source code path is injected into shell command using environment
variable using force_set_env().
Commiter notice:
When building with DEBUG=1 we get a compiler error that gets fixed with
the same approach described in commit b236512280fb:
perf kmem: Fix compiler warning about may be accessing uninitialized variable
The last argument to strtok_r doesn't need to be initialized, its
just a placeholder to make this routine reentrant, but gcc doesn't know
about that and complains, breaking the build, fix it by setting it to
NULL.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/n/1436445342-1402-14-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patch introduces [llvm] config section with 5 options. Following
patches will use then to config llvm dynamica compiling.
'llvm-utils.[ch]' is introduced in this patch for holding all
llvm/clang related stuffs.
Example:
[llvm]
# Path to clang. If omit, search it from $PATH.
clang-path = "/path/to/clang"
# Cmdline template. Following line shows its default value.
# Environment variable is used to passing options.
#
# *NOTE*: -D__KERNEL__ MUST appears before $CLANG_OPTIONS,
# so user have a chance to use -U__KERNEL__ in $CLANG_OPTIONS
# to cancel it.
clang-bpf-cmd-template = "$CLANG_EXEC -D__KERNEL__ $CLANG_OPTIONS \
$KERNEL_INC_OPTIONS -Wno-unused-value \
-Wno-pointer-sign -working-directory \
$WORKING_DIR -c $CLANG_SOURCE -target \
bpf -O2 -o -"
# Options passed to clang, will be passed to cmdline by
# $CLANG_OPTIONS.
clang-opt = "-Wno-unused-value -Wno-pointer-sign"
# kbuild directory. If not set, use /lib/modules/`uname -r`/build.
# If set to "" deliberately, skip kernel header auto-detector.
kbuild-dir = "/path/to/kernel/build"
# Options passed to 'make' when detecting kernel header options.
kbuild-opts = "ARCH=x86_64"
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/r/1437477214-149684-1-git-send-email-wangnan0@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Extend the event parser maximum error index from 10 to 13. That allows
PMU config terms of up to 10 characters to display un-truncated in the
error message.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-17-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Currently the value of a PMU config term is silently truncated if it is
too big. This is an impediment to validating the value for other
criteria later on i.e. the user provides an invalid value that gets
truncated to a valid one.
The maximum value validation is only done for the parser where the error
is passed back to the user. In other cases the silent truncation
continues so as not to affect tools that perhaps rely on it.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-16-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add perf_pmu__format_bits() to get the format bits for a PMU config
term. Intel PT will use this to validate terms and to record format
bits to enable later interpreting the config from the attribute stored
in the perf.data file.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-15-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
PERF_ITRACE_PERIOD_INSTRUCTIONS is zero so it got overwritten by the
default period type.
Fix by checking if the period type was set rather than if the value was
zero when applying the default.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lkml.kernel.org/r/1437150840-31811-12-git-send-email-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Display the cycles by default in branch sort mode.
To make enough room for the new column I removed dso_to. It is usually
redundant with dso_from.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1437233094-12844-9-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Now that we can process branch data in annotate it makes sense to
support enabling branch recording from top too. Most of the code needed
for this is already in shared code with report. But we need to add:
- The option parsing code (using shared code from the previous patch)
- Document the options
- Set up the IPC/cycles accounting state in the top session
- Call the accounting code in the hist iter callback
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1437233094-12844-8-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Add two new columns to the annotate display and display the average
cycles and the compute IPC if available.
When the LBR was not in any branch mode the IPC computation is
automatically disabled. We still display the cycle information.
Example output (with made up numbers):
The second column is the IPC and third average cycles.
│ __attribute__((noinline)) f2()
│ {
5.15 0.07 │ push %rbp
0.01 0.07 │ mov %rsp,%rbp
│ c = a / b;
9.87 0.07 │ mov a,%eax
0.07 │ mov b,%ecx
0.07 │ cltd
4.92 0.07 123│ idiv %ecx
70.79 0.07 │ mov %eax,__TMC_END__
│ }
9.25 0.07 │ pop %rbp
0.01 0.07 123│ ← retq
v2: Fix display problems.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1437233094-12844-7-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Compute the IPC and the basic block cycles for the annotate display.
IPC is computed by counting the instructions, and then dividing the
accounted cycles by that count.
The actual IPC computation can only be done at annotate time, because we
need to parse the objdump output first to know the number of
instructions in the basic block.
The cycles/IPC are also put into the perf function annotation so that
the display code can show them.
Again basic block overlaps are not handled, with the longest winning,
but there are some heuristics to hide the IPC when the longest is not
the most common.
v2: Compute IPC correctly.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1437233094-12844-6-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Call the earlier added cycle histogram infrastructure from the perf
report hist iter callback. For this we walk the branch records.
This allows to use cycle histograms when browsing perf report annotate.
v2: Rename flag
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1437233094-12844-5-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This adds the basic infrastructure to keep track of cycle counts per
basic block for annotate. We allocate an array similar to the normal
accounting, and then account branch cycles there.
We handle two cases:
cycles per basic block with start and cycles per branch (these are later
used for either IPC or just cycles per BB)
In the start case we cannot handle overlaps, so always the longest basic
block wins.
For the cycles per branch case everything is accurately accounted.
v2: Remove unnecessary checks. Slight restructure. Move
symbol__get_annotation to another patch. Move histogram allocation.
v3: Merged with current tree
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1437233094-12844-4-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Later patches need to cheaply check that the branch mode is in ANY. Add
a new function to check all event attrs and add a flag to the report
state, which is then initialized.
v2: Rename flag
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1437233094-12844-3-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
cycles is a new branch_info field available on some CPUs that indicates
the time deltas between branches in the LBR.
Add a sort key and output code for the cycles to allow to display the
basic block cycles individually in perf report.
We also pass in the cycles for weight when LBRs are processed, which
allows to get global and local weight, to get an estimate of the total
cost.
And also print the cycles information for perf report -D. I also added
printing for the previously missing LBR flags (mispredict etc.)
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1437233094-12844-2-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
perf currently fails to build on MIPS as there is no
tools/perf/arch/mips/Build file. Adding an empty file fixes this as
there are no MIPS-specific sources to build.
It looks like the same is needed for Alpha and PA-RISC, though I
haven't been able to test those.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Fixes: 5e8c0fb6a9 ("perf build: Add arch x86 objects building")
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1438704627.7315.2.camel@decadent.org.uk
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Moving counter processing code into stat object as
perf_stat__process_counter.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1437481927-29538-8-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Passing 'struct perf_stat_config' into process_counter(), so that we can
make process_counter() non static and use it from other places.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1437481927-29538-7-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Moving 'interval' into struct perf_stat_config. The point is to
centralize the base stat config so it could be used localy together with
other stat routines in other parts of perf code.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1437481927-29538-6-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Moving 'output' into struct perf_stat_config. The point is to centralize
the base stat config so it could be used localy together with other stat
routines in other parts of perf code.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1437481927-29538-5-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Moving 'scale' into struct perf_stat_config. The point is to centralize
the base stat config so it could be used localy together with other stat
routines in other parts of perf code.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1437481927-29538-4-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Moving 'aggr_mode' into new struct. The point is to centralize the base
stat config so it could be used localy together with other stat routines
in other parts of perf code.
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Link: http://lkml.kernel.org/r/1437481927-29538-3-git-send-email-jolsa@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Commit 7b6ff0bdbf ("perf probe ppc64le:
Fixup function entry if using kallsyms lookup") adds 'struct map' into
probe-event.h but not forward declares it. This patch fixes it.
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Alexei Starovoitov <ast@plumgrid.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Fixes: 7b6ff0bdbf ("perf probe ppc64le: Fixup function entry if using kallsyms lookup")
Link: http://lkml.kernel.org/n/1436445342-1402-30-git-send-email-wangnan0@huawei.com
[ No need to include map.h, just forward declare 'struct map' ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
va_args alternative to eprintf().
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Cc: Brendan Gregg <brendan.d.gregg@gmail.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: David Ahern <dsahern@gmail.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Kaixu Xia <xiakaixu@huawei.com>
Cc: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Zefan Li <lizefan@huawei.com>
Cc: pi3orama@163.com
Link: http://lkml.kernel.org/n/1436445342-1402-19-git-send-email-wangnan0@huawei.com
[ split from another patch ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Without this patch, it is cumbersome to read the trace output but
ignoring the normal, potentially verbose, output of the debuggee. One
common example is doing something like the following:
perf trace -s find /tmp > /dev/null
Without this patch, the trace summary will be lost. Now, it will still
be printed at the end. This behavior is also applied by strace.
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: David Ahern <dsahern@gmail.com>
Link: http://lkml.kernel.org/n/tip-tqnks6y2cnvm5f9g2dsfr7zl@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
color_vprintf was including the length of the invisible escape sequences
in its return argument. Don't include them to make the return value
usable for indentation calculations.
v2: Add comment, rebase
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1438649408-20807-3-git-send-email-andi@firstfloor.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Seems like it's always '\n' through color_fprintf_ln, which is not used
at all, removing.. ;-)
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/r/1438649408-20807-2-git-send-email-andi@firstfloor.org
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Pass global callchain_param into parse_callchain_record_opt and
perf_evsel__config_callgraph as parameter. So we can reuse these
functions to parse/config local param for callchain.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1438677022-34296-3-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This patchkit adds the ability to turn off time stamps per event.
One usaful case for partial time is to work with per-event callgraph to
enable "PEBS threshold > 1" (https://lkml.org/lkml/2015/5/10/196), which
can significantly reduce the sampling overhead.
The event samples with time stamps off will not be ordered.
Signed-off-by: Kan Liang <kan.liang@intel.com>
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Link: http://lkml.kernel.org/r/1438677022-34296-2-git-send-email-kan.liang@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To work like strace and dereference syscall pointer args we need to
insert probes (or tracepoints) right after we copy those bytes from
userspace.
Since we're formatting the syscall args at raw_syscalls:sys_enter time,
we need to have a formatter that just stores the position where, later,
when we get the probe:vfs_getname, we can insert the pointer contents.
Now, if a probe:vfs_getname with this format is in place:
# perf probe -l
probe:vfs_getname (on getname_flags:72@/home/git/linux/fs/namei.c with pathname)
That was, in this case, put in place with:
# perf probe 'vfs_getname=getname_flags:72 pathname=filename:string'
Added new event:
probe:vfs_getname (on getname_flags:72 with pathname=filename:string)
You can now use it in all perf tools, such as:
perf record -e probe:vfs_getname -aR sleep 1
#
Then 'perf trace' will notice that and do the pointer -> contents
expansion:
# trace -e open touch /tmp/bla
0.165 (0.010 ms): touch/17752 open(filename: /etc/ld.so.cache, flags: CLOEXEC) = 3
0.195 (0.011 ms): touch/17752 open(filename: /lib64/libc.so.6, flags: CLOEXEC) = 3
0.512 (0.012 ms): touch/17752 open(filename: /usr/lib/locale/locale-archive, flags: CLOEXEC) = 3
0.582 (0.012 ms): touch/17752 open(filename: /tmp/bla, flags: CREAT|NOCTTY|NONBLOCK|WRONLY, mode: 438) = 3
#
Roughly equivalent to strace's output:
# strace -rT -e open touch /tmp/bla
0.000000 open("/etc/ld.so.cache", O_RDONLY|O_CLOEXEC) = 3 <0.000039>
0.000317 open("/lib64/libc.so.6", O_RDONLY|O_CLOEXEC) = 3 <0.000102>
0.001461 open("/usr/lib/locale/locale-archive", O_RDONLY|O_CLOEXEC) = 3 <0.000072>
0.000405 open("/tmp/bla", O_WRONLY|O_CREAT|O_NOCTTY|O_NONBLOCK, 0666) = 3 <0.000055>
0.000641 +++ exited with 0 +++
#
Now we need to either look for at all syscalls that are marked as
pointers and have some well known names ("filename", "pathname", etc)
and set the arg formatter to the one used for the "open" syscall in this
patch.
This implementation works for syscalls with just a string being copied
from userspace, for matching syscalls with more than one string being
copied via the same probe/trace point (vfs_getname) we need to extend
the vfs_getname probe spec to include the pointer too, but there are
some problems with that in 'perf probe' or the kernel kprobes code, need
to investigate before considering supporting multiple strings per
syscall.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Milian Wolff <mail@milianw.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-xvuwx6nuj8cf389kf9s2ue2s@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We were using it as a magic number, 1024, fix that.
Eventually we need to stop doing it per line, and do it per
arg, traversing the args at output time, to avoid the memmove()
calls that will be used in the next cset to replace pointers
present at raw_syscalls:sys_enter time with its contents that
appear at probe:vfs_getname time, before raw_syscalls:sys_exit
time.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Milian Wolff <mail@milianw.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-4sz3wid39egay1pp8qmbur4u@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So that we can later decide if we will store where to expand the
pathname once we are handling vfs_getname or if we should instead
just go on and straight away print the pointer.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Milian Wolff <mail@milianw.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-ytxk5s5jpc50wahffmlxgxuw@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
We were accessing trace->syscalls.events members even when that struct
wasn't initialized, i.e. --no-syscalls was specified on the command
line, fix it to show that, still in debug mode, when we have an event
qualifier list, i.e. when we actually are doing subset syscall tracing.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Milian Wolff <mail@milianw.de>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Fixes: 19867b6186 ("perf trace: Use event filters for the event qualifier list")
Link: http://lkml.kernel.org/n/tip-7980ym6vujgh3yiai0cqzc88@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
The libtraceevent handler (session->tevent) is only initialized when
there are tracepoints in a perf.data event list, so do not call
pevent_set_function_resolve() in those cases, fixing a segfault.
Reported-by: Jiri Olsa <jolsa@kernel.org>
Tested-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Borislav Petkov <bp@suse.de>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Stephane Eranian <eranian@google.com>
Link: http://lkml.kernel.org/n/tip-xyynkucl5p4bcs13zi4i4b1f@git.kernel.org
Report-link: http://lkml.kernel.org/r/20150803174113.GA20282@krava.redhat.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Adrian Hunter