When the error of the same bit rate is detected, we will need to select
the recive margin is large. Current code holds the minimum error, it does
not have to check the recive margin. This adds this calculation.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If bit-rate calculation result of HSCIF is expect 255 from 0,
driver does not calculate error bit. However, we need to round
the value to calculate error bit in the case of negative value.
This rounds the value of bit-rate using clamp(), and bit-rate is the
case of negative value, it enables the calculation of the error bit.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the decimal point is discarded calculation of BRR.
Therefore, it can not calculate a value close to the correct value.
This patch fixes this problem by using DIV_ROUND_CLOSEST.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here's the big tty/serial driver update for 3.15-rc1.
Nothing major, a number of serial driver updates and a few tty core
fixes as well.
All have been in linux-next for a while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlM7CWAACgkQMUfUDdst+ylDXACg0vZ+J+5OXbbE3lywVCAebjhB
XzkAn1lz7JRIils7IlckAJ2w/m50b174
=M+8c
-----END PGP SIGNATURE-----
Merge tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver update from Greg KH:
"Here's the big tty/serial driver update for 3.15-rc1.
Nothing major, a number of serial driver updates and a few tty core
fixes as well.
All have been in linux-next for a while"
* tag 'tty-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (71 commits)
tty/serial: omap: empty the RX FIFO at the end of half-duplex TX
tty/serial: omap: fix RX interrupt enable/disable in half-duplex TX
serial: sh-sci: Neaten dev_<level> uses
serial: sh-sci: Replace hardcoded 3 by UART_PM_STATE_OFF
serial: sh-sci: Add more register documentation
serial: sh-sci: Remove useless casts
serial: sh-sci: Replace printk() by pr_*()
serial_core: Avoid NULL pointer dereference in uart_close()
serial_core: Get a reference for port->tty in uart_remove_one_port()
serial: clps711x: Give a chance to perform useful tasks during wait loop
serial_core: Grammar s/ports/port's/
serial_core: Spelling s/contro/control/
serial: efm32: properly namespace location property
serial: max310x: Add missing #include <linux/uaccess.h>
synclink: fix info leak in ioctl
serial: 8250: Clean up the locking for -rt
serial: 8250_pci: change BayTrail default uartclk
serial: 8250_pci: more BayTrail error-free bauds
serial: sh-sci: Add missing call to uart_remove_one_port() in failure path
serial_core: Unregister console in uart_remove_one_port()
...
Two cpufreq notifiers CPUFREQ_RESUMECHANGE and CPUFREQ_SUSPENDCHANGE have
not been used for some time, so remove them to clean up code a bit.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
[rjw: Changelog]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Make banner const while we're at it
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Acked-by: Simon Horman <horms@verge.net.au>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If cpufreq_register_notifier() fails, we have to remove the port added by
sci_probe_single(), which is not done by sci_cleanup_single().
Else the serial port stays active from the point of view of the serial
subsystem, and it may crash when userspace getty is started, or when the
loadable driver module is unloaded.
This was introduced by commit 6dae14216c
("serial: sh-sci: Fix probe error paths").
Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following compile warning about cast to pointer from
integer of different size.
drivers/tty/serial/sh-sci.c:2021:19: warning: cast to pointer from integer of different size [-Wint-to-pointer-cast]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Extend the driver to with support for SCIx device tree bindings. A
minimal set of features is supported, additional properties can be added
later should the need to describe more device features arise.
Signed-off-by: Bastian Hecht <hechtb+renesas@gmail.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The fields are not used anymore by board files, remove them.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The field isn't set by any board, remote it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Computing the baud rate register value requires knowledge of the
hardware sampling rate. This information is currently encoded in a baud
rate calculation algorithm ID passed through platform data. However, it
can be derived from the port type directly in most cases.
Compute the sampling rate internally in the driver if the baud rate
calculation algorithm ID isn't specified, and allow platforms to
override the sampling rate through platform data in special cases (this
is only required for SCIFA ports on sh7723 and sh7724, the reason needs
to be investigated).
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The overrun bit index is a property of the hardware. It's currently
computed based on a different and unrelated hardware property, the baud
rate calculation algorithm. Compute it using hardware identification
information only.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver requests at initialization time GPIOs passed through platform
data. No platform makes use of this feature, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
None of the fields is ever set by board code, and both of them are set
in the driver at probe time. Move them out of struct plat_sci_port to
struct sci_port.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Memory and IRQ resources are currently passed to the driver through
platform data. Support passing them through the standard platform
resources mechanism instead. This deprecates platform data resources.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The IRQ number can't be modified by the user as the port is fixed.
There's no need to check the new IRQ number as it will be ignored by the
core.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The base address, IRQ and baud rate generator parent clock rate can't be
changed by userspace. Mark the port as fixed.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The driver checks if the interrupt number is greater than nr_irqs and
returns an error in that case. The same check is already performed by
the caller, remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Rewrite the baud rate register value calculations in easier to read
forms. The computed value isn't modified.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Turn clk_enable() and clk_disable() calls into clk_prepare_enable() and
clk_disable_unprepare() to get ready for the migration to the common
clock framework.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
The break timer accesses hardware registers and thus requires the port
to be enabled. It currently ensures this by enabling the port at the
beginning of the timer handler, and disabling it at the end. However,
the enable/disable operations call the runtime PM sync functions, which
are not allowed in atomic context. The current situation is thus broken.
This change relies on non-atomic code to enable/disable the port. The
break timer will only be started from the IRQ handler, which already
runs with the port enabled. We just need to ensure that the port won't
be disabled with the timer running, and that's easily done by just
cancelling the timer in the port disable function.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the %zu and %pad printk specifiers to print size_t and dma_addr_t
variables, and cast pointers to uintptr_t instead of unsigned int where
applicable. This fixes warnings on platforms where pointers and/or
dma_addr_t have a different size than int.
Cc: linux-serial@vger.kernel.org
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This change addresses two warnings that are flagged by gcc relating to
potential access to the ssr and cks variables while they are uninitialised.
I have addressed this by initialising the values to
the defaults present in sci_baud_calc_hscif().
It is my analysis that cks is always initialised if used
but that without this change ssr may be accessed while uninitialised.
The code altered by this patch was introduced by commit
f303b364b4 ("serial: sh-sci: HSCIF support").
Reported-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Adds support for "High Speed Serial Communications Interface with FIFO",
essentially a SCIF with 128-byte FIFOs and more accurate baud rate
generator.
Signed-off-by: Ulrich Hecht <ulrich.hecht@gmail.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
Now, the one where most of tty_port_tty_get gets removed:
tty_flip_buffer_push.
IOW we also closed all the races in drivers not using tty_port_tty_get
at all yet.
Also we move tty_flip_buffer_push declaration from include/linux/tty.h
to include/linux/tty_flip.h to all others while we are changing it
anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty in many
call sites. Only tty_port will needed and hence no more
tty_port_tty_get in those paths.
tty_insert_flip_char is the next one to proceed. This one is used all
over the code, so the patch is huge.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now, we start converting tty buffer functions to actually use
tty_port. This will allow us to get rid of the need of tty pointer in
many call sites. Only tty_port will be needed and hence no more
tty_port_tty_get calls in those paths.
Here we start with tty_buffer_request_room.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Cc: Lucas Tavares <lucaskt@linux.vnet.ibm.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Tony Prisk <linux@prisktech.co.nz>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In the previous commit, console write function (serial_console_write)
is changed to disable SCI interrupts while printing console strings.
This introduces possible race cases in the serial startup / shutdown
functions on SMP systems.
This patch fixes the sh-sci in the same way as commit 9ec1882df2
(tty: serial: imx: console write routing is unsafe on SMP, from
Xinyu Chen <xinyu.chen@freescale.com>, 2012-08-27) did.
There could be several consumers of the console,
* the kernel printk
* the init process using /dev/kmsg to call printk to show log
* shell, which opens /dev/console and writes with sys_write()
The shell goes into the normal UART open() and write() system calls,
while the other two go into the console operations. The open() call
invokes serial startup function (sci_startup), which will write to
the SCSCR register (to enable or disable SCI interrupts) without any
locking. This will conflict with the console serial function.
Add spinlock protections in sci_startup() and sci_shutdown() properly.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Symptom:
When entering the suspend with Android logcat running, printk() call
gets stuck and never returns. The issue can be observed at printk()s
on nonboot CPUs when going to offline with their interrupts disabled,
and never seen at boot CPU (core0 in our case).
Details:
serial_console_write() lacks of appropriate spinlock handling.
In SMP systems, as long as sci_transmit_chars() is being processed
at one CPU core, serial_console_write() can stuck at the other CPU
core(s), when it tries to access to the same serial port _without_
a proper locking. serial_console_write() waits for the transmit FIFO
getting empty, while sci_transmit_chars() writes data to the FIFO.
In general, peripheral interrupts are routed to boot CPU (core0) by
Linux ARM standard affinity settings. SCI(F) interrupts are handled
by core0, so sci_transmit_chars() is processed on core0 as well.
When logcat is running, it writes enormous log data to the kernel at
every moment, forever. So core0 can repeatedly continue to process
sci_transmit_chars() in its interrupt handler, which eventually makes
the other CPU core(s) stuck at serial_console_write().
Looking at serial/8250.c, this is a known console write lockup issue
with SMP kernels. Fix the sh-sci driver in the same way 8250.c does.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
About FIFO count, there are two variants of SCIFs which show
a) TX count in upper, RX count in lower byte of FDR register
b) TX count in TFDR register, RX count in RFDR register
Common SCIFB regmap in current source code is defined as "a".
At least 7372 and 73a0 HW manual say their SICFB are "b".
This patch alters the definition to "b", considering the current
one has come from a mistake. The reason is as follows.
The flag SCIFB sh-sci driver means it has 256 byte FIFO.
The count is from 0(empty) to 256(full), that makes 9-bit.
Because FDR is 16-bit register, it can not hold two 9-bits.
That's why, SCIFB can not be "a".
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Current mask 0xff to SCTFDR/RFDR damages SCIFB, because the
registers on SCIFB have 9-bit data (0 to 256).
This patch changes the mask according to port->fifosize.
Though I'm not sure if the mask is really needed (I don't know if
there are variants which have non-zero upper bits), it is safer.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Support prescaler 1/16 and 1/64, in addition to current 1 and 1/4.
Supporting below 2400bps was dropped long time ago in mainline.
Since then, setting lower rate has been resulting in erroneous
register value, without indicating any errors through API.
This patch adds more prescaler to support lower rates again.
This still doesn't check range, but we won't hit the case because
even 50bps at 48MHz clock is now supported.
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit 1ba7622094 (serial: sh-sci: console Runtime PM support,
from Magnus Damm <damm@opensource.se>, 2011-08-03), tried to support
console runtime PM, but unfortunately it didn't work for us for some
reason. We did not investigated further at that time, instead would
like to propose a different approach.
In Linux tty/serial world, to get console PM work properly, a serial
client driver does not have to maintain .runtime_suspend()/..resume()
calls itself, but can leave console power power management handling to
the serial core driver.
This patch moves the sh-sci driver in that direction.
Notes:
* There is room to optimize console runtime PM more aggressively by
maintaining additional local runtime PM calls, but as a first step
having .pm() operation would suffice.
* We still have a couple of direct calls to sci_port_enable/..disable
left in the driver. We have to live with them, because they're out
of serial core's help.
Signed-off-by: Teppei Kamijou <teppei.kamijou.yb@renesas.com>
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This partially reverts commit 1ba7622094 (serial: sh-sci: console
Runtime PM support, from Magnus Damm <damm@opensource.se>, 2011-08-03).
The generic 'serial_core' can take care of console PM maintenance,
so all (or at least the first thing) we have to do to get console PM
work properly, is to implement uart_ops ->pm() operation in the sh-sci
serial client driver.
This patch partially reverts the commit above, but leaving sci_reset()
change in place, because sci_reset() is already part of another commit
(73c3d53f38 serial: sh-sci: Avoid FIFO clear for MCE toggle.).
A revised version of console PM support follows next.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 5a50a01bf0 (sh-sci / PM: Use power.irq_safe, from
Rafael J. Wysocki <rjw@sisk.pl>, 2011-08-24).
In order to get console PM work properly, we should implement uart_ops
->pm() operation, rather than sprinkle band-ading runtime PM calls in
the driver.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 048be431e4 (sh-sci / PM: Avoid deadlocking runtime
PM, from Rafael J. Wysocki <rjw@sisk.pl>, 2012-03-09).
In order to get console PM work properly, we should implement uart_ops
->pm() operation, rather than sprinkle band-ading runtime PM calls in
the driver.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It was already pointed out how to fix these cases before the offending
patches were merged, but unsurprisingly, that didn't happen. As this
change is entirely superfluous to begin with, simply shut things up by
casting everything away.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Nobuhiro Iwamatsu