PCIe PMU Root Complex Integrated End Point(RCiEP) device is supported
to sample bandwidth, latency, buffer occupation etc.
Each PMU RCiEP device monitors multiple Root Ports, and each RCiEP is
registered as a PMU in /sys/bus/event_source/devices, so users can
select target PMU, and use filter to do further sets.
Filtering options contains:
event - select the event.
port - select target Root Ports. Information of Root Ports are
shown under sysfs.
bdf - select requester_id of target EP device.
trig_len - set trigger condition for starting event statistics.
trig_mode - set trigger mode. 0 means starting to statistic when bigger
than trigger condition, and 1 means smaller.
thr_len - set threshold for statistics.
thr_mode - set threshold mode. 0 means count when bigger than threshold,
and 1 means smaller.
Acked-by: Krzysztof Wilczyński <kw@linux.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Reviewed-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/20211202080633.2919-3-liuqi115@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
The PA PMU counter offset was correct in [1] and the driver has
already been verified. We want to keep the register offset using
lower case character in later version that is consistent with
the existed driver. Since there was no functional change, we
didn't do more test. However there is typo when modified the PA
PMU counter offset by mistake, so fix this bad mistake.
[1] https://www.spinics.net/lists/arm-kernel/msg865263.html
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: John Garry <john.garry@huawei.com>
Cc: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/20210928123022.23467-1-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
These are only put in an array of pointers to const attribute_group
structs. Make them const like the other static attribute_group structs
to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20210605221514.73449-1-rikard.falkeborn@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
'Data source' is a new function for HHA PMU and config / clear
interface was wrong by mistake. 'HHA_DATSRC_CTRL' register is
mainly used for data source configuration, if we enable bit0
as driver, it will go on count the event and we didn't check
it carefully. So fix the issue and do as the initial purpose.
Fixes: 932f6a99f9 ("drivers/perf: hisi: Add new functions for HHA PMU")
Reported-by: kernel test robot <lkp@intel.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1622709291-37996-1-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
These drivers use irq_set_affinity_hint() to set the affinity for the PMU
interrupts, which relies on the undocumented side effect that this function
actually sets the affinity under the hood.
Setting an hint is clearly not a guarantee and for these PMU interrupts an
affinity hint, which is supposed to guide userspace for setting affinity,
is beyond pointless, because the affinity of these interrupts cannot be
modified from user space.
Aside of that the error checks are bogus because the only error which is
returned from irq_set_affinity_hint() is when there is no irq descriptor
for the interrupt number, but not when the affinity set fails. That's on
purpose because the hint can point to an offline CPU.
Replace the mindless abuse with irq_set_affinity().
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210518093118.813375875@linutronix.de
Signed-off-by: Will Deacon <will@kernel.org>
On HiSilicon Hip09 platform, there is a PA (Protocol Adapter) module on
each chip SICL (Super I/O Cluster) which incorporates three Hydra interface
and facilitates the cache coherency between the dies on the chip. While PA
uncore PMU model is the same as other Hip09 PMU modules and many PMU events
are supported. Let's support the PMU driver using the HiSilicon uncore PMU
framework.
PA PMU supports the following filter functions:
* tracetag_en: allows user to count events according to tt_req or
tt_core set in L3C PMU. It's the same as other PMUs.
* srcid_cmd & srcid_msk: allows user to filter statistics that come from
specific CCL/ICL by configuration source ID.
* tgtid_cmd & tgtid_msk: it is the similar function to srcid_cmd &
srcid_msk. Both are used to check where the data comes from or go to.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Co-developed-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1615186237-22263-9-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
HiSilicon's Hip09 is comprised by multi-dies that can be connected by SLLC
module (Skyros Link Layer Controller), its has separate PMU registers which
the driver can program it freely and interrupt is supported to handle
counter overflow. Let's support its driver under the framework of HiSilicon
uncore PMU driver.
SLLC PMU supports the following filter functions:
* tracetag_en: allows user to count data according to tt_req or
tt_core set in L3C PMU.
* srcid_cmd & srcid_msk: allows user to filter statistics that come from
specific CCL/ICL by configuration source ID.
* tgtid_hi & tgtid_lo: it also supports event statistics that these
operations will go to the CCL/ICL by configuration target ID or
target ID range. It's the same as source ID with 11-bit width in
the SoC. More introduction is added in documentation:
Documentation/admin-guide/perf/hisi-pmu.rst
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Co-developed-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1615186237-22263-8-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
DDRC PMU's events are useful for performance profiling, but the events
are limited and counter is fixed. On HiSilicon Hip09 platform, PMU
counters are the programmable and more events are supported. Let's
add the DDRC PMU v2 driver.
Bandwidth events are exposed directly in driver and some more events
will listed in JSON file later.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Co-developed-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1615186237-22263-7-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
On HiSilicon Hip09 platform, some new functions are also supported on
HHA PMU.
* tracetag_en: it is the abbreviation of tracetag enable and allows user
to count events according to tt_req or tt_core set in L3C PMU.
* datasrc_skt: it is the abbreviation of data source from another
socket and it is used in the multi-chips. It's the same as L3C PMU.
* srcid_cmd & srcid_msk: pair of the fields are used to filter
statistics that come from the specific CCL/ICL by the configuration.
These are the abbreviation of source ID command and mask. The source
ID is 11-bit and detailed descriptions are documented in
Documentation/admin-guide/perf/hisi-pmu.rst.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Co-developed-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1615186237-22263-6-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
On HiSilicon Hip09 platform, some new functions are enhanced on L3C PMU:
* tt_req: it is the abbreviation of tracetag request and allows user to
count only read/write/atomic operations. tt_req is 3-bit and details are
listed in the hisi-pmu document.
$# perf stat -a -e hisi_sccl3_l3c0/config=0x02,tt_req=0x4/ sleep 5
* tt_core: it is the abbreviation of tracetag core and allows user to
filter by core/thread within the cluster, it is a 8-bit bitmap that each
bit represents the corresponding core/thread in this L3C.
$# perf stat -a -e hisi_sccl3_l3c0/config=0x02,tt_core=0xf/ sleep 5
* datasrc_cfg: it is the abbreviation of data source configuration and
allows user to check where the data comes from, such as: from local DDR,
cross-die DDR or cross-socket DDR. Its is 5-bit and represents different
data source in the SoC.
$# perf stat -a -e hisi_sccl3_l3c0/dat_access,datasrc_cfg=0xe/ sleep 5
* datasrc_skt: it is the abbreviation of data source from another socket
and is used in the multi-chips, if user wants to check the cross-socket
datat source, it shall be added in perf command. Only one bit is used to
control this.
$# perf stat -a -e hisi_sccl3_l3c0/dat_access,datasrc_cfg=0x10,datasrc_skt=1/ sleep 5
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Co-developed-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1615186237-22263-5-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
For HiSilicon uncore PMU, more versions are supported and some variables
shall be added suffix to distinguish the version which are prepared for
the new drivers.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Co-developed-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1615186237-22263-4-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
On HiSilicon uncore PMU drivers, interrupt handling function and interrupt
registration function are very similar in differents PMU modules. Let's
refactor the frame.
Two new callbacks are added for the HW accessors:
* hisi_uncore_ops::get_int_status returns a bitmap of events which
have overflowed and raised an interrupt
* hisi_uncore_ops::clear_int_status clears the overflow status for a
specific event
These callback functions are used by a common IRQ handler,
hisi_uncore_pmu_isr().
One more function hisi_uncore_pmu_init_irq() is added to replace each
PMU initialization IRQ interface and simplify the code.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Co-developed-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1615186237-22263-3-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
The sanity check for counter index has been done in the function
hisi_uncore_pmu_get_event_idx, so remove the redundant interface
hisi_uncore_pmu_counter_valid() and sanity check.
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: John Garry <john.garry@huawei.com>
Cc: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Co-developed-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1615186237-22263-2-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
sprintf does not know the PAGE_SIZE maximum of the temporary buffer
used for sysfs content and it's possible to overrun the buffer length.
Use sysfs_emit() function to ensures that no overrun is done.
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Link: https://lore.kernel.org/r/1616148273-16374-4-git-send-email-liuqi115@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
Fix the following coccicheck warning:
./drivers/perf/hisilicon/hisi_uncore_pmu.c:128:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/fsl_imx8_ddr_perf.c:173:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm_spe_pmu.c:129:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm_smmu_pmu.c:563:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm_dsu_pmu.c:149:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm_dsu_pmu.c:139:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm-cmn.c:563:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm-cmn.c:351:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm-ccn.c:224:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm-cci.c:708:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm-cci.c:699:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm-cci.c:528:8-16: WARNING: use scnprintf or sprintf.
./drivers/perf/arm-cci.c:309:8-16: WARNING: use scnprintf or sprintf.
Signed-off-by: Zihao Tang <tangzihao1@hisilicon.com>
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Link: https://lore.kernel.org/r/1616148273-16374-2-git-send-email-liuqi115@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
The only usage is to put their addresses in an array of pointers to
const struct attribute group. Make them const to allow the compiler
to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20210117212847.21319-4-rikard.falkeborn@gmail.com
Signed-off-by: Will Deacon <will@kernel.org>
To allow userspace to identify the specific implementation of the device,
add an "identifier" sysfs file.
Encoding is as follows (same for all uncore drivers):
hi1620: 0x0
hi1630: 0x30
Signed-off-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1602149181-237415-2-git-send-email-john.garry@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
MODULE_*** is used in HiSilicon uncore PMU drivers and is provided by
linux/module.h, but the header file is not directly included. Add the
missing include.
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/1599186097-18599-1-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
Forcefully unbinding PMU drivers during perf sampling will lead to
a kernel panic, because the perf upper-layer framework call a NULL
pointer in this situation.
To solve this issue, "suppress_bind_attrs" should be set to true, so
that bind/unbind can be disabled via sysfs and prevent unbinding PMU
drivers during perf sampling.
Signed-off-by: Qi Liu <liuqi115@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Link: https://lore.kernel.org/r/1594975763-32966-1-git-send-email-liuqi115@huawei.com
Signed-off-by: Will Deacon <will@kernel.org>
In L3C uncore PMU drivers, bit16 is used to control all counters enable &
disable. Wrong value is given in the driver and its default value is 1'b1,
it can work because each PMU counter has its own control bits too.
Let's fix the wrong value.
Fixes: 2940bc4333 ("perf: hisi: Add support for HiSilicon SoC L3C PMU driver")
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/1591350221-32275-1-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
This patch lets HiSilicon uncore PMU driver can be built as modules.
A common module and three specific uncore PMU driver modules will be built.
Export necessary functions in hisi_uncore_pmu module, and change
irq_set_affinity to irq_set_affinity_hint to pass compile.
Signed-off-by: Zhou Wang <wangzhou1@hisilicon.com>
Tested-by: Qi Liu <liuqi115@huawei.com>
Reviewed-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Link: https://lore.kernel.org/r/1588820305-174479-1-git-send-email-wangzhou1@hisilicon.com
Signed-off-by: Will Deacon <will@kernel.org>
hisi_read_sccl_and_ccl_id is not readable and its comment is a little
confused, so simplify the function and its comment as Mark's suggestion.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Suggested-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will@kernel.org>
For some HiSilicon platform, the originally designed SCCL_ID and CCL_ID
are not satisfied with much rich topology when the MT is set, so we
extend the SCCL_ID to MPIDR[aff3] and CCL_ID to MPIDR[aff2]. Let's
update this for HiSilicon uncore PMU driver.
Cc: John Garry <john.garry@huawei.com>
Cc: Hanjun Guo <guohanjun@huawei.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will@kernel.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Will Deacon <will@kernel.org>
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Will Deacon <will@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Will Deacon <will@kernel.org>
Based on 2 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 4122 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
PERF_PMU_CAP_NO_EXCLUDE capability. This ensures that perf will
prevent us from handling events where any exclusion flags are set.
Let's also remove the now unnecessary check for exclusion flags.
Signed-off-by: Andrew Murray <andrew.murray@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Arnaldo Carvalho de Melo <acme@kernel.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: robin.murphy@arm.com
Cc: suzuki.poulose@arm.com
Link: https://lkml.kernel.org/r/1547128414-50693-8-git-send-email-andrew.murray@arm.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
For DDRC PMU, each PMU counter is fixed-purpose. There is a mismatch
between perf list and driver definition on rw_chg event.
# perf list | grep chg
hisi_sccl1_ddrc0/rnk_chg/ [Kernel PMU event]
hisi_sccl1_ddrc0/rw_chg/ [Kernel PMU event]
But the register offset of rw_chg event is not defined in the driver,
meanwhile bnk_chg register offset is mis-defined, let's fixup it.
Fixes: 904dcf03f0 ("perf: hisi: Add support for HiSilicon SoC DDRC PMU driver")
Cc: stable@vger.kernel.org
Cc: John Garry <john.garry@huawei.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Reported-by: Weijian Huang <huangweijian4@hisilicon.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
MT bit in MPIDR_EL1 is now supported in certain HiSilicon platforms, so
the mapping between sccl_id/ccl_id and affinity level needs to be updated
from the generic encoding we originally used.
Cc: John Garry <john.garry@huawei.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
[will: fixed comment]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Now that all the grouping is done with RB trees, we no longer need
group_entry and can replace the whole thing with sibling_list.
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Alexey Budankov <alexey.budankov@linux.intel.com>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: David Carrillo-Cisneros <davidcc@google.com>
Cc: Dmitri Prokhorov <Dmitry.Prohorov@intel.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Kan Liang <kan.liang@intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Valery Cherepennikov <valery.cherepennikov@intel.com>
Cc: Vince Weaver <vincent.weaver@maine.edu>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This patch adds support for DDRC PMU driver in HiSilicon SoC chip, Each
DDRC has own control, counter and interrupt registers and is an separate
PMU. For each DDRC PMU, it has 8-fixed-purpose counters which have been
mapped to 8-events by hardware, it assumes that counter index is equal
to event code (0 - 7) in DDRC PMU driver. Interrupt is supported to
handle counter (32-bits) overflow.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Anurup M <anurup.m@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
L3 cache coherence is maintained by Hydra Home Agent (HHA) in HiSilicon
SoC. This patch adds support for HHA PMU driver, Each HHA has own
control, counter and interrupt registers and is an separate PMU. For
each HHA PMU, it has 16-programable counters and each counter is
free-running. Interrupt is supported to handle counter (48-bits)
overflow.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Anurup M <anurup.m@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds support for L3C PMU driver in HiSilicon SoC chip, Each
L3C has own control, counter and interrupt registers and is an separate
PMU. For each L3C PMU, it has 8-programable counters and each counter
is free-running. Interrupt is supported to handle counter (48-bits)
overflow.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Anurup M <anurup.m@huawei.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
This patch adds support HiSilicon SoC uncore PMU driver framework and
interfaces.
Acked-by: Mark Rutland <mark.rutland@arm.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Anurup M <anurup.m@huawei.com>
[will: Fix leader accounting in uncore group validation]
Signed-off-by: Will Deacon <will.deacon@arm.com>
Qi Liu