If a timeout is hit, it can result is incorrect data on the I2C bus
and/or memory corruptions in the guest since the device can still be
operating on the buffers it was given while the guest has freed them.
Here is, for example, the start of a slub_debug splat which was
triggered on the next transfer after one transfer was forced to timeout
by setting a breakpoint in the backend (rust-vmm/vhost-device):
BUG kmalloc-1k (Not tainted): Poison overwritten
First byte 0x1 instead of 0x6b
Allocated in virtio_i2c_xfer+0x65/0x35c age=350 cpu=0 pid=29
__kmalloc+0xc2/0x1c9
virtio_i2c_xfer+0x65/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in virtio_i2c_xfer+0x32e/0x35c age=244 cpu=0 pid=29
kfree+0x1bd/0x1cc
virtio_i2c_xfer+0x32e/0x35c
__i2c_transfer+0x429/0x57d
i2c_transfer+0x115/0x134
i2cdev_ioctl_rdwr+0x16a/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
There is no simple fix for this (the driver would have to always create
bounce buffers and hold on to them until the device eventually returns
the buffers), so just disable the timeout support for now.
Fixes: 3cfc883804 ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Jie Deng <jie.deng@intel.com>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Currently interrupt storm will occur from i2c-i801 after first
transaction if SMB_ALERT signal is enabled and ever asserted. It is
enough if the signal is asserted once even before the driver is loaded
and does not recover because that interrupt is not acknowledged.
This fix aims to fix it by two ways:
- Add acknowledging for the SMB_ALERT interrupt status
- Disable the SMB_ALERT interrupt on platforms where possible since the
driver currently does not make use for it
Acknowledging resets the SMB_ALERT interrupt status on all platforms and
also should help to avoid interrupt storm on older platforms where the
SMB_ALERT interrupt disabling is not available.
For simplicity this fix reuses the host notify feature for disabling and
restoring original register value.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=177311
Reported-by: ck+kernelbugzilla@bl4ckb0x.de
Reported-by: stephane.poignant@protonmail.com
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If driver interrupts are enabled, SMBHSTCNT_INTREN will be 1 after
the first transaction, and will stay to that value forever. This
means that interrupts will be generated for both host-initiated
transactions and also SMBus Alert events even after the driver is
unloaded. To be on the safe side, we should restore the initial state
of this bit at suspend and reboot time, as we do for several other
configuration bits already and for the same reason: the BIOS should
be handed the device in the same configuration state in which we
received it. Otherwise interrupts may be generated which nobody
will process.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commits 95b8a5e011 ("MIPS: Remove NETLOGIC support") and edd4488aea
("ARM: remove tango platform") removed Netlogic XLR and Sigma Designs
Tango platforms which means there are no platforms using the XLR I2C
driver and it can be removed.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Netlogic XLP was removed in commit 95b8a5e011 ("MIPS: Remove NETLOGIC
support"). With those gone, the single platform left to support is
Cavium ThunderX2. Remove the Netlogic variant and DT support.
For simplicity, the existing kconfig name is retained.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by George Cherian <gcherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
A separate Kconfig option HAVE_S3C2410_I2C for Samsung SoCs is not
really needed and the i2c-s3c24xx driver can depend on Samsung ARM
architectures instead. This also enables i2c-s3c2410 for arm64 Exynos
SoCs, which is required for example by Exynos850.
This is basically continuation of work made in following commits:
- commit d96890fca9 ("rtc: s3c: remove HAVE_S3C_RTC in favor of
direct dependencies")
- commit 7dd3cae90d ("ARM: samsung: remove HAVE_S3C2410_WATCHDOG and
use direct dependencies")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Link: https://lore.kernel.org/r/20211121150558.21801-2-semen.protsenko@linaro.org
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Pull i2c updates from Wolfram Sang:
- big refactoring of the PASEMI driver to support the Apple M1
- huge improvements to the XIIC in terms of locking and SMP safety
- refactoring and clean ups for the i801 driver
... and the usual bunch of small driver updates
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (43 commits)
i2c: amd-mp2-plat: ACPI: Use ACPI_COMPANION() directly
i2c: i801: Add support for Intel Ice Lake PCH-N
i2c: virtio: update the maintainer to Conghui
i2c: xlr: Fix a resource leak in the error handling path of 'xlr_i2c_probe()'
i2c: qup: move to use request_irq by IRQF_NO_AUTOEN flag
i2c: qup: fix a trivial typo
i2c: tegra: Ensure that device is suspended before driver is removed
i2c: i801: Fix incorrect and needless software PEC disabling
i2c: mediatek: Dump i2c/dma register when a timeout occurs
i2c: mediatek: Reset the handshake signal between i2c and dma
i2c: mlxcpld: Allow flexible polling time setting for I2C transactions
i2c: pasemi: Set enable bit for Apple variant
i2c: pasemi: Add Apple platform driver
i2c: pasemi: Refactor _probe to use devm_*
i2c: pasemi: Allow to configure bus frequency
i2c: pasemi: Move common reset code to own function
i2c: pasemi: Split pci driver to its own file
i2c: pasemi: Split off common probing code
i2c: pasemi: Remove usage of pci_dev
i2c: pasemi: Use dev_name instead of port number
...
The ACPI_HANDLE() macro is a wrapper arond the ACPI_COMPANION()
macro and the ACPI handle produced by the former comes from the
ACPI device object produced by the latter, so it is way more
straightforward to evaluate the latter directly instead of passing
the handle produced by the former to acpi_bus_get_device().
Modify i2c_amd_probe() accordingly (no intentional functional impact).
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add PCI ID of SMBus controller on Intel Ice Lake PCH-N.
The device can be found on MacBookPro16,2 [1].
[1]: https://linux-hardware.org/?probe=f1c5cf0c43
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
PTR_ERR should access the value just tested by IS_ERR, otherwise
the wrong error code will be returned.
Fixes: 7b6da7fe7b ("mailbox: pcc: Use PCC mailbox channel pointer instead of standard")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Hardening work by Jason
vdpa driver for Alibaba ENI
Performance tweaks for virtio blk
virtio rng rework using an internal buffer
mac/mtu programming for mlx5 vdpa
Misc fixes, cleanups
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmF/su8PHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpo+sIAJjBTvbET+d0KuIMt8YBGsU+NWgHaJxW06hm
GHZzinueZYWaS20MPMYMPfcHUgigWj0kk7F0gMljG5rtDFzR85JkOi7+e5V6RVJW
8SQc7JjA1Krde6EiPJdlv3mVkLz/5VbrGUgjAW9di/O04Xc/jAc9kmJ41wTYr0mL
E5IsUi9QBmgHtKQ+2ofb9QEWuebJclGK+NVd3Kp08BtAQOrdn5UrIzY30/sjkZwE
ul2ll6v/k7T3dCQbHD/wMgfFycPvoZVfxaVj+FWQnwdWkqZwzMRmpKPRes4KJfww
Lfx1qox10mJzH7XJCs7xmOM8f7HgNNWi0gD5FxNlfkiz1AwHYOk=
=DTXY
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"vhost and virtio fixes and features:
- Hardening work by Jason
- vdpa driver for Alibaba ENI
- Performance tweaks for virtio blk
- virtio rng rework using an internal buffer
- mac/mtu programming for mlx5 vdpa
- Misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (45 commits)
vdpa/mlx5: Forward only packets with allowed MAC address
vdpa/mlx5: Support configuration of MAC
vdpa/mlx5: Fix clearing of VIRTIO_NET_F_MAC feature bit
vdpa_sim_net: Enable user to set mac address and mtu
vdpa: Enable user to set mac and mtu of vdpa device
vdpa: Use kernel coding style for structure comments
vdpa: Introduce query of device config layout
vdpa: Introduce and use vdpa device get, set config helpers
virtio-scsi: don't let virtio core to validate used buffer length
virtio-blk: don't let virtio core to validate used length
virtio-net: don't let virtio core to validate used length
virtio_ring: validate used buffer length
virtio_blk: correct types for status handling
virtio_blk: allow 0 as num_request_queues
i2c: virtio: Add support for zero-length requests
virtio-blk: fixup coccinelle warnings
virtio_ring: fix typos in vring_desc_extra
virtio-pci: harden INTX interrupts
virtio_pci: harden MSI-X interrupts
virtio_config: introduce a new .enable_cbs method
...
The virtio specification received a new mandatory feature
(VIRTIO_I2C_F_ZERO_LENGTH_REQUEST) for zero length requests. Fail if the
feature isn't offered by the device.
For each read-request, set the VIRTIO_I2C_FLAGS_M_RD flag, as required
by the VIRTIO_I2C_F_ZERO_LENGTH_REQUEST feature.
This allows us to support zero length requests, like SMBUS Quick, where
the buffer need not be sent anymore.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/7c58868cd26d2fc4bd82d0d8b0dfb55636380110.1634808714.git.viresh.kumar@linaro.org
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jie Deng <jie.deng@intel.com> # once the spec is merged
Now that we have all the shared memory region information populated in
the pcc_mbox_chan, let us propagate the pointer to the same as the
return value to pcc_mbox_request channel.
This eliminates the need for the individual users of PCC mailbox to
parse the PCCT subspace entries and fetch the shmem information. This
also eliminates the need for PCC mailbox controller to set con_priv to
PCCT subspace entries. This is required as con_priv is private to the
controller driver to attach private data associated with the channel and
not meant to be used by the mailbox client/users.
Let us convert all the users of pcc_mbox_{request,free}_channel to use
new interface.
Cc: Jean Delvare <jdelvare@suse.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
A successful 'clk_prepare()' call should be balanced by a corresponding
'clk_unprepare()' call in the error handling path of the probe, as already
done in the remove function.
More specifically, 'clk_prepare_enable()' is used, but 'clk_disable()' is
also already called. So just the unprepare step has still to be done.
Update the error handling path accordingly.
Fixes: 75d31c2372 ("i2c: xlr: add support for Sigma Designs controller variant")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
disable_irq() after request_irq() still has a time gap in which
interrupts can come. request_irq() with IRQF_NO_AUTOEN flag will
disable IRQ auto-enable because of requesting.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Correct the typo of "reamining" to "remaining".
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Suggested-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Tegra I2C device isn't guaranteed to be suspended after removal of
the driver since driver uses pm_runtime_put() that is asynchronous and
pm_runtime_disable() cancels pending power-change requests. This means
that potentially refcount of the clocks may become unbalanced after
removal of the driver. This a very minor problem which unlikely to
happen in practice and won't cause any visible problems, nevertheless
let's replace pm_runtime_disable() with pm_runtime_force_suspend() and
use pm_runtime_put_sync() which disables RPM of the device and puts it
into suspend before driver is removed.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit a6b8bb6a81 ("i2c: i801: Fix handling SMBHSTCNT_PEC_EN")
attempts to disable software PEC by clearing the SMBHSTCNT_PEC_EN (bit 7)
in the SMBus Host Control register (I/O SMBHSTCNT) but incorrectly
clears it in the PCI Host Configuration register (PCI SMBHSTCFG).
This clearing is actually needless since after above commit the
SMBHSTCNT_PEC_EN is never set and the register is initialized with known
values.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Acked-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When a timeout error occurs in i2c transter, it is usually related
to the i2c/dma IP hardware configuration. Therefore, the purpose of
this patch is to dump the key register values of i2c/dma when a
timeout occurs in i2c for debugging.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Due to changes in the hardware design of the handshaking signal
between i2c and dma, it is necessary to reset the handshaking
signal before each transfer to ensure that the multi-msgs can
be transferred correctly.
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Allow polling time setting according to I2C frequency supported across
the system. For base frequency 400 KHz and 1 MHz set polling time is set
four times less than for system with base frequency 100KHz.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Some later revisions after the original PASemi I2C controller introduce
what likely is an enable bit to the CTL register. Without setting it the
actual i2c transmission is never started.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
With all the previous preparations we can now finally add
the platform driver to support the PASemi-based controllers
in Apple SoCs. This does not work on the M1 yet but should
work on the early iPhones already.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Using managed device resources means there's nothing left to be done in
pasemi_smb_pci_remove and also allows to remove base and size from
struct pasemi_smbus.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Right now the bus frequency has always been hardcoded as
100 KHz with the specific reference clock used in the PASemi
PCI controllers. Make this configurable to prepare for the
platform driver.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Split out common reset call to its own function so that we
can later add support for selecting the clock frequency
and an additional enable bit found in newer revisions.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Split off the PCI driver so that we can reuse common code for the
platform driver.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Split off common probing code that will be used by both the PCI and the
platform device.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Prepare to create a platform driver by removing all usages of pci_dev we
can.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Right now the i2c adapter name includes the port number which can
indirectly be used to identify the device. Replace that with dev_name
to directly identify the device and to also allow this to work correctly
once we add platform support.
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In preparation for splitting this driver up into a platform_driver
and a pci_driver, replace outl/inl usage with pci_iomap and
ioread32/iowrite32.
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sven Peter <sven@svenpeter.dev>
Acked-by: Olof Johansson <olof@lixom.net>
Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Decrease polling time 'MLXCPLD_I2C_POLL_TIME' from 400 usec to 200
usec. It improves performance of I2C transactions.
Reliability of setting polling time to 200 usec has been validated
across all the supported systems.
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Change setting for 400KHz frequency support by more accurate value.
Fixes: 66b0c2846b ("i2c: mlxcpld: Add support for I2C bus frequency setting")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Value for getting frequency capability wrongly has been taken from
register offset instead of register value.
Fixes: 66b0c2846b ("i2c: mlxcpld: Add support for I2C bus frequency setting")
Signed-off-by: Vadim Pasternak <vadimp@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Describe better which driver applies to which SoC, to make configuring
kernel for Samsung SoC easier.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The MODULE_DEVICE_TABLE already creates proper alias for platform
driver. Having another MODULE_ALIAS causes the alias to be duplicated.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In the commit be5ce0e97c ("i2c: mediatek: Add i2c ac-timing adjust
support"), we miss setting OFFSET_EXT_CONF register if
i2c->dev_comp->timing_adjust is false, now add it back.
Fixes: be5ce0e97c ("i2c: mediatek: Add i2c ac-timing adjust support")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The reason for the modification here is that the previous
offset information is incorrect, OFFSET_DEBUGSTAT = 0xE4 is
the correct value.
Fixes: 25708278f8 ("i2c: mediatek: Add i2c support for MediaTek MT8183")
Signed-off-by: Kewei Xu <kewei.xu@mediatek.com>
Reviewed-by: Chen-Yu Tsai <wenst@chromium.org>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Warn users that class based instantiation is going away soon in favour
of more robust probing and faster bootup times.
Class based instantiation has already been removed for other controllers
and it makes absolutely sense to do it for this one too.
Signed-off-by: Michael Brunner <michael.brunner@kontron.com>
Acked-by: Ingmar Klein <ingmar.klein@kontron.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When call function devm_platform_ioremap_resource(), we should use IS_ERR()
to check the return value and return PTR_ERR() if failed.
Signed-off-by: zhaoxiao <long870912@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We want to enable the interrupts _before_ starting the transfer because
it is good programming style and also the proposed order in the R-Car
manual. There is no difference in practice because it doesn't matter in
which order both conditions appear if we wait for both to happen.
Signed-off-by: Ryo Kataoka <ryo.kataoka.wt@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The original change works as intended, but Andy pointed in [0] that now
userspace could re-enable RPM via sysfs, even though we explicitly want
to disable it. So effectively revert the original patch, just with small
improvements:
- Calls to pm_runtime_allow()/pm_runtime_forbid() don't have to be
balanced, so we can remove the call to pm_runtime_forbid() in
i801_remove().
- priv->acpi_reserved is accessed after i801_acpi_remove(), and according
to Robert [1] the custom handler can't run any longer. Therefore we
don't have to take priv->acpi_lock.
[0] https://www.spinics.net/lists/linux-i2c/msg52730.html
[1] https://lore.kernel.org/linux-acpi/BYAPR11MB32561D19A0FD9AB93E2B1E5287D39@BYAPR11MB3256.namprd11.prod.outlook.com/T/#t
Fixes: 4e60d5dd10 ("i2c: i801: Improve disabling runtime pm")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Rafael J. Wysocki <rafael@kernel.org>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As pointed out by Andy in [0] using a local mutex here isn't strictly
wrong but not sufficient. We should hold the PCI rescan lock for P2SB
operations.
[0] https://www.spinics.net/lists/linux-i2c/msg52717.html
Fixes: 1a987c69ce ("i2c: i801: make p2sb_spinlock a mutex")
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The return value of i801_add_mux() isn't used, so let's change it to void.
In addition remove the not needed cast to struct gpiod_lookup.
GPIO_LOOKUP() uses GPIO_LOOKUP_IDX() that includes this cast.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
By using ACPI_HANDLE() the handler argument can be retrieved directly.
Both address space handler functions check the handler argument and
return an error if it's NULL. This allows to further simplify the code.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
do_pci_enable_device() takes care that PCI_COMMAND_INTX_DISABLE
is cleared if a legacy interrupt is used.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Replace the ugly cast of the return_value pointer with proper usage.
In addition use dmi_match() instead of open-coding it.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In case the XIIC does TX/RX transfer, make sure no other kernel thread
can start another TX transfer at the same time. This could happen since
the driver only checks tx_msg for being non-NULL and returns -EBUSY in
that case, however it is necessary to check also rx_msg for the same.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Transferring multiple messages via XIIC suffers from strange interaction
between the interrupt status/enable register flags. These flags are being
reused in the hardware to indicate different things for read and write
transfer, and doing multiple transactions becomes horribly complex. Just
send a single transaction and reload the controller with another message
once the transaction is done in the interrupt handler thread.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
There will never be threads queueing up in the xiic_xmit(), use
completion synchronization primitive to wait for the interrupt
handler thread to complete instead as it is much better fit and
there is no need to overload it for this purpose.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The __xiic_start_xfer() manipulates the interrupt flags, xiic_wakeup()
may result in return from xiic_xfer() early. Defer both to the end of
the xiic_process() interrupt thread, so that they are executed after
all the other interrupt bits handling completed and once it completely
safe to perform changes to the interrupt bits in the hardware.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The interrupt handler is missing locking when reading out registers
and is racing with other threads which might access the driver. Drop
it altogether, so that the threaded interrupt is always executed, as
that one is already serialized by the driver mutex. This also allows
dropping local_irq_save()/local_irq_restore() in xiic_start_recv().
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The tx_msg is set from multiple places, sometimes without locking,
which fall apart on any SMP system. Only ever access tx_msg inside
the driver mutex.
Signed-off-by: Marek Vasut <marex@denx.de>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
"I2C has a smaller pull reuest this time:
- new driver for I2C virtio
- removal of PMC SMP driver because platform is already gone
- IRQ probing and DMAENGINE API cleanups
- add SI metric prefix definitions to units.h
- beginning of i801 refactorization
- a few driver improvements"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (28 commits)
i2c: cadence: Implement save restore
i2c: xlp9xx: fix main IRQ check
i2c: mt65xx: fix IRQ check
i2c: virtio: add a virtio i2c frontend driver
i2c: hix5hd2: fix IRQ check
i2c: s3c2410: fix IRQ check
i2c: iop3xx: fix deferred probing
i2c: synquacer: fix deferred probing
i2c: sun6i-pw2i: Prefer strscpy over strlcpy
i2c: remove dead PMC MSP TWI/SMBus/I2C driver
i2c: dev: Use sysfs_emit() in "show" functions
i2c: dev: Define pr_fmt() and drop duplication substrings
i2c: designware: Fix indentation in the header
i2c: designware: Use DIV_ROUND_CLOSEST() macro
units: Add SI metric prefix definitions
i2c: at91: mark PM ops as __maybe unused
i2c: sh_mobile: : use proper DMAENGINE API for termination
i2c: qup: : use proper DMAENGINE API for termination
i2c: mxs: : use proper DMAENGINE API for termination
i2c: imx: : use proper DMAENGINE API for termination
...
The zynqmp platform now supports chip-off so the registers can
lose context.
Implement save restore for i2c module.
Since we have only a couple of registers
an unconditional restore is done.
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Shubhrajyoti Datta <shubhrajyoti.datta@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0 for the main IRQ, the driver's probe()
method will return 0 early (as if the method's call was successful).
Let's consider IRQ0 valid for simplicity -- devm_request_irq() can always
override that decision...
Fixes: 2bbd681ba2 ("i2c: xlp9xx: Driver for Netlogic XLP9XX/5XX I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: George Cherian <george.cherian@marvell.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: ce38815d39 ("I2C: mediatek: Add driver for MediaTek I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add an I2C bus driver for virtio para-virtualization.
The controller can be emulated by the backend driver in
any device model software by following the virtio protocol.
The device specification can be found on
https://lists.oasis-open.org/archives/virtio-comment/202101/msg00008.html.
By following the specification, people may implement different
backend drivers to emulate different controllers according to
their needs.
Co-developed-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Conghui Chen <conghui.chen@intel.com>
Signed-off-by: Jie Deng <jie.deng@intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: 15ef27756b ("i2c: hix5hd2: add i2c controller driver")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Iff platform_get_irq() returns 0, the driver's probe() method will return 0
early (as if the method's call was successful). Let's consider IRQ0 valid
for simplicity -- devm_request_irq() can always override that decision...
Fixes: e0d1ec9785 ("i2c-s3c2410: Change IRQ to be plain integer.")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
When adding the code to handle platform_get_irq*() errors in the commit
489447380a ("handle errors returned by platform_get_irq*()"), the
actual error code was enforced to be -ENXIO in the driver for some
strange reason. This didn't matter much until the deferred probing was
introduced -- which requires an actual error code to be propagated
upstream from the failure site.
While fixing this, also stop overriding the errors from request_irq() to
-EIO (done since the pre-git era).
Fixes: 489447380a ("[PATCH] handle errors returned by platform_get_irq*()")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver overrides the error codes returned by platform_get_irq() to
-ENODEV, so if it returns -EPROBE_DEFER, the driver will fail the probe
permanently instead of the deferred probing. Switch to propagating the
error codes upstream.
Fixes: 0d676a6c43 ("i2c: add support for Socionext SynQuacer I2C controller")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
strlcpy() reads the entire source buffer first. This read may exceed the
destination size limit. This is both inefficient and can lead to linear
read overflows if a source string is not NUL-terminated. The safe
replacement is strscpy().
This is a previous step in the path to remove the strlcpy() function
entirely from the kernel [1].
[1] https://github.com/KSPP/linux/issues/89
Signed-off-by: Len Baker <len.baker@gmx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Commit 1b00767fd8 ("MIPS: Remove PMC MSP71xx platform") removes the
config PMC_MSP in ./arch/mips/Kconfig.
Hence, since then, the corresponding PMC MSP TWI/SMBus/I2C driver is
dead code. Remove this dead driver.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In couple of places the indentation makes harder to read the code.
Fix it to be sane.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Instead of open-coding DIV_ROUND_CLOSEST() and similar use the macros directly.
While at it, replace numbers with predefined SI metric prefixes.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver uses pm_ptr(), so the PM ops could be unused.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: dab4b0e8c9 ("i2c: at91: remove #define CONFIG_PM")
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we want dmaengine_terminate_sync()
because there is no other synchronization code in the driver to handle
an async case.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Remove #define CONFIG_PM and use __maybe_unused for PM functions and
pm_ptr() for PM ops.
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
Reviewed-by: Codrin Ciubotariu <codrin.ciubotariu@microchip.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Switch to use module_parport_driver() to reduce boilerplate code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If a user is interested in such details he can enable smbus tracing.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
p2sb_spinlock is used in i801_add_tco_spt() only, and in process context
only. Therefore a mutex is sufficient, and we can make the definition
local to i801_add_tco_spt().
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Setting the autosuspend delay to a negative value disables runtime pm in
a little bit smarter way, because we need no cleanup when removing the
driver. Note that this is safe when reloading the driver, because the
call to pm_runtime_set_autosuspend_delay() in probe() will reverse the
effect. See update_autosuspend() for details.
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver is written as if platform_get_irq() returns 0 on errors (while
actually it returns a negative error code), blithely passing these error
codes to request_irq() (which takes *unsigned* IRQ #) -- which fails with
-EINVAL. Add the necessary error check to the pre-existing *if* statement
forcing the driver into the polling mode...
Fixes: 4ad48e6ab1 ("i2c: Renesas Highlander FPGA SMBus support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omp.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Bit SMBHSTCNT_PEC_EN is used only if software calculates the CRC and
uses register SMBPEC. This is not supported by the driver, it supports
hw-calculation of CRC only (using bit SMBAUXSTS_CRCE). The chip spec
states the following, therefore never set bit SMBHSTCNT_PEC_EN.
Chapter SMBus CRC Generation and Checking
If the AAC bit is set in the Auxiliary Control register, the PCH
automatically calculates and drives CRC at the end of the transmitted
packet for write cycles, and will check the CRC for read cycles. It will
not transmit the contents of the PEC register for CRC. The PEC bit must
not be set in the Host Control register. If this bit is set, unspecified
behavior will result.
This patch is based solely on the specification and compile-tested only,
because I have no PEC-capable devices.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
During some transfers the bus can still be busy when an interrupt is
received. Commit 763778cd79 ("i2c: mpc: Restore reread of I2C status
register") attempted to address this by re-reading MPC_I2C_SR once but
that just made it less likely to happen without actually preventing it.
Instead of a single re-read, poll with a timeout so that the bus is given
enough time to settle but a genuine stuck SCL is still noticed.
Fixes: 1538d82f46 ("i2c: mpc: Interrupt driven transfer")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Pull i2c updates from Wolfram Sang:
- core supports now bus regulators controlling power for SCL/SDA
- quite some DT binding conversions to YAML
- added a seperate DT binding for the optional SMBus Alert feature
- documentation with examples how to deal with I2C sysfs files
- some bigger rework for the i801 driver
- and a few usual driver updates
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (42 commits)
i2c: ali1535: mention that the device should not be disabled
i2c: mpc: Restore reread of I2C status register
i2c: core-smbus: Expose PEC calculate function for generic use
Documentation: i2c: Add doc for I2C sysfs
i2c: core: Disable client irq on reboot/shutdown
dt-bindings: i2c: update bindings for MT8195 SoC
i2c: imx: Fix some checkpatch warnings
i2c: davinci: Simplify with dev_err_probe()
i2c: cadence: Simplify with dev_err_probe()
i2c: xiic: Simplify with dev_err_probe()
i2c: cadence: Clear HOLD bit before xfer_size register rolls over
dt-bindings: i2c: ce4100: Replace "ti,pcf8575" by "nxp,pcf8575"
i2c: i801: Improve i801_setup_hstcfg
i2c: i801: Use driver name constant instead of function dev_driver_string
i2c: i801: Simplify initialization of i2c_board_info in i801_probe_optional_slaves
i2c: i801: Improve status polling
i2c: cht-wc: Replace of_node by NULL
i2c: riic: Add RZ/G2L support
dt-bindings: i2c: renesas,riic: Document RZ/G2L I2C controller
dt-bindings: i2c: renesas,iic: Convert to json-schema
...
The comment from the i801 driver is valid here, too, so copy it.
Reported-by: Jean Delvare <jdelvare@suse.de>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Prior to commit 1538d82f46 ("i2c: mpc: Interrupt driven transfer") the
old interrupt handler would reread MPC_I2C_SR after checking the CSR_MIF
bit. When the driver was re-written this was removed as it seemed
unnecessary. However as it turns out this is necessary for i2c devices
which do clock stretching otherwise we end up thinking the bus is still
busy when processing the interrupt.
Fixes: 1538d82f46 ("i2c: mpc: Interrupt driven transfer")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The direction of the pipe argument must match the request-type direction
bit or control requests may fail depending on the host-controller-driver
implementation.
Control transfers without a data stage are treated as OUT requests by
the USB stack and should be using usb_sndctrlpipe(). Failing to do so
will now trigger a warning.
Fix the OSIFI2C_SET_BIT_RATE and OSIFI2C_STOP requests which erroneously
used the osif_usb_read() helper and set the IN direction bit.
Reported-by: syzbot+9d7dadd15b8819d73f41@syzkaller.appspotmail.com
Fixes: 83e53a8f12 ("i2c: Add bus driver for for OSIF USB i2c device.")
Cc: stable@vger.kernel.org # 3.14
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Fix the following warnings reported by checkpatch::
drivers/i2c/busses/i2c-imx.c:173: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:175: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:176: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:177: WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
drivers/i2c/busses/i2c-imx.c:455: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:602: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:638: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:1170: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:1374: WARNING: Unnecessary ftrace-like logging - prefer using ftrace
drivers/i2c/busses/i2c-imx.c:1398: WARNING: Prefer strscpy over strlcpy - see: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Kwon Tae-young <tykwon@m2i.co.kr>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
On Xilinx zynq SOC if the delay between address register write and
control register write in cdns_mrecv function is more, the xfer size
register rolls over and controller is stuck. This is an IP bug and
is resolved in later versions of IP.
To avoid this scenario, disable the interrupts on the current processor
core between the two register writes and enable them later. This can
help achieve the timing constraint.
Signed-off-by: Raviteja Narayanam <raviteja.narayanam@xilinx.com>
Acked-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We need to add a check for if the kzalloc() fails.
Fixes: 4a7695429e ("i2c: cp2615: add i2c driver for Silicon Labs' CP2615 Digital Audio Bridge")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Bence Csókás <bence98@sch.bme.hu>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
As explained in [0] currently we may leave SMBHSTSTS_INUSE_STS set,
thus potentially breaking ACPI/BIOS usage of the SMBUS device.
Seems patch [0] needs a little bit more of review effort, therefore
I'd suggest to apply a part of it as quick win. Just clearing
SMBHSTSTS_INUSE_STS when leaving i801_access() should fix the
referenced issue and leaves more time for discussing a more
sophisticated locking handling.
[0] https://www.spinics.net/lists/linux-i2c/msg51558.html
Fixes: 01590f361e ("i2c: i801: Instantiate SPD EEPROMs automatically")
Suggested-by: Hector Martin <marcan@marcan.st>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Hector Martin <marcan@marcan.st>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
i801_setup_hstcfg() leaves the bits in priv->original_hstcfg that
we're interested in intact. Therefore we can remove the return value
from the function and use priv->original_hstcfg directly.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
We are the driver, so we can use the driver name directly instead of
retrieving it by calling dev_driver_string().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Why shall we bother to open-code something that the compiler can do for us.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Polling uses the same timeout as irq mode: 400 * 500us = 200ms = HZ / 5.
So let's use the adapter->timeout value also for polling. This has the
advantage that userspace can control the timeout value for polling as
well. In addition change the code to make it better readable.
Last but not least remove the timeout debug messages. Calls to both
functions are followed by a call to i801_check_post() that will print
an error message in case of timeout.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver is run on the platforms where OF node is always NULL.
The confusion comes from IRQ domain APIs that take either OF or
firmware node as input parameter. Since fwnode is not used here
either, replace of_node by NULL.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
RZ/G2L i2c controller is compatible with RZ/A i2c controller.
By default IP is in reset state, so need to perform release
reset before accessing any register.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Vincent Whitchurch