Commit Graph

12 Commits

Author SHA1 Message Date
Jisheng Zhang 1531675269 mmc: sdhci-st: use sdhci_pltfm_init for private allocation
Commit 0e74823429 ("mmc: sdhci: Add size for caller in init+register")
allows users of sdhci_pltfm to allocate private space in calls to
sdhci_pltfm_init+sdhci_pltfm_register. This patch migrates sdhci-st
to this allocation.

Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2016-02-29 11:03:29 +01:00
Zhangfei Gao e6ac184bdd mmc: sdhci-st: Fix modalias to make module auto-loading work
Make the modalias match driver name, this is required to make module
auto-loading work.

Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
CC: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01 09:07:07 +02:00
Peter Griffin 4e187d3154 mmc: sdhci-st: Update the quirks for this controller.
Some additional quirks need to be enabled now we support UHS
modes. This avoids some spurious warnings like

"Got data interrupt 0x00000002 even though no data operation was in progress"

Testing on stih410-b2120 board achieves the following speeds
with HS200 eMMC card.

max-frequency = 200Mhz
/dev/mmcblk0p1:
 Timing buffered disk reads: 270 MB in  3.02 seconds =  89.54 MB/sec

max-frequency = 100Mhz
root@debian-armhf:~# hdparm -t /dev/mmcblk0p1
/dev/mmcblk0p1:
 Timing buffered disk reads: 210 MB in  3.00 seconds =  70.00 MB/sec

max-frequency = 50Mhz
root@debian-armhf:~# hdparm -t /dev/mmcblk0p1
/dev/mmcblk0p1:
 Timing buffered disk reads: 118 MB in  3.00 seconds =  39.28 MB/sec

This is better than the 3.10 kernel which achieves 77.59 MB/sec
at 200Mhz clock (same board/soc/eMMC).

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-04-10 12:55:40 +02:00
Peter Griffin cf48d32efb mmc: sdhci-st: Add sdhci_st_set_uhs_signaling function.
To allow UHS modes to work properly we need to provide the st specific
set_uhs_signaling callback function. This function differs from the
generic sdhci_set_uhs_signaling callback in that we need to configure
the correct delay depending on the UHS mode, and also set the V18_EN
bit.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-04-10 12:55:40 +02:00
Peter Griffin 2053812f6e mmc: sdhci-st: Add st_mmcss_cconfig function to configure mmcss glue registers.
STiH407 family SoC's have glue registers in the flashSS subsystem which
are used to configure the Arasan HC. This patch configures these glue
registers according to what has been specified in the DT.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-04-10 12:55:40 +02:00
Peter Griffin bfa448041f mmc: sdhci-st: Add delay management functions for top registers (eMMC).
Due to the tight timing constraints in some UHS modes, it is required to have
some delay management in the design. Two types of delay management are supported
in the HW: -

1) Static delay management
2) Dynamic delay management

NB: The delay management is only there when eMMC interface is selected.

1: Static delay management: is used to provide PVT dependent static delay on the
clock/data lines to manage setup/hold requirements of the interface. The maximum
delay possible is 3.25ns. These delays are PVT dependent, and thus delay values
applied are not accurate and vary across provcess voltage and temperature range.
Due to this these delays must not be used on the very time critical paths.

2. Dynamic delay locked loop (DLL): is used to provide dynamic delay management.
The advantage of DLL is that it provides accurate & PVT indepedent delay.

The DLL is used to provide delay on the loopback clock on "Read Path" to capture
read data reliably. On TX path the clock on which output data is transmitted is
delayed, resulting in delay of TX data.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-04-10 12:55:40 +02:00
Peter Griffin 406c24310a mmc: sdhci-st: Add support for de-asserting reset signal and top regs resource
STiH407 family SoC's can have a reset signal for the controller which needs to
be managed. Also the eMMC controller has some additional 'top' memory mapped
registers which are used to manage the dynamic and static delay required for
UHS modes. This patch adds support for creating the mapping, which will be used
by subsequent patches.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-04-10 12:55:39 +02:00
Peter Griffin 8bef7178a6 mmc: sdhci-st: Add macros for register offsets and bitfields for mmcss glue regs
The stih407 family SoC's have additional glue registers in the flashSS which
are used to configure the Arasan controller.

This patch adds macros for the register offsets and bitfields which will be
used by subsequent patches to support stih407 family SoC's.

Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-04-10 12:55:39 +02:00
Kevin Hao caebcae94f mmc: sdhci: set the .remove to sdhci_pltfm_unregister()
In these drivers, the driver specific .remove function just a simple
wrapper of function sdhci_pltfm_unregister(). So remove these wrappers
and just set .remove to sdhci_pltfm_unregister().

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-03-23 14:13:35 +01:00
Kevin Hao 83eacdfa25 mmc: sdhci: disable the clock in sdhci_pltfm_unregister()
So we can avoid to sprinkle the clk_disable_unprepare() in many
drivers.

Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-03-23 14:13:34 +01:00
Ulf Hansson fc702cb35d mmc: sdhci-st: Do cleanup while mmc_of_parse() return an error
At errors, balance sdhci_pltfm_init() with sdhci_pltfm_free(), to make
sure all data is freed properly.

Cc: Srinivas Kandagatla <srinivas.kandagatla@gmail.com>
Cc: Maxime Coquelin <maxime.coquelin@st.com>
Cc: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
2015-01-19 09:56:14 +01:00
Peter Griffin f52d9c4f45 mmc: sdhci-st: Intial support for ST SDHCI controller
This platform driver adds initial support for the SDHCI host controller
found on STMicroelectronics SoCs.

It has been tested on STiH41x b2020 platforms currently.

Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Maxime Coquelin <maxime.coquelin@st.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-07-10 09:11:18 +02:00