Now that we've removed direct calls from interrupt handler to
omap2430_musb_set_vbus(), let's make things less confusing and
configure VBUS directly in omap_musb_set_mailbox().
We have omap_musb_set_mailbox() called from the PHYs, and that's
all we need.
Note that we can now also drop the check for MUSB_INTERFACE_UTMI,
we've been already calling otg_set_vbus(musb->xceiv->otg, 0)
unconditionally via omap2430_musb_set_vbus() and we should only
need to call it once.
And we want to disable VBUS unconditionally on disconnect even
without musb->gadget_driver, so let's drop that check too.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-11-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We want to configure musb state in omap2430_musb_enable() instead of
omap2430_musb_init(). Otherwise musb may not idle properly until
USB cable has been connected at least once.
And we already have omap_musb_set_mailbox() configure mode with
omap_control_usb_set_mode() so we can remove those calls from
omap2430_musb_enable().
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-10-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There should be no need to tinker with devctl in enable in the SoC glue
code. We have musb_start() to take care of handling it already.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-9-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At least some revisions of musb core need to set devctl session bit
in peripheral mode to force musb to host mode. And we have places
clearing the devctl session bit.
Let's add a generic function to do this, and use it for omap2430.
This should get us a bit closer to completely removing devctl register
tinkering in the SoC glue code.
Before making use of this code for the other glue layers, things need
to be tested carefully as there may be a approximately a 200 ms delay
needed between powering up musb and calling musb_set_host() to avoid.
Otherwise the system hangs at least with omap2430 glue layer.
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
[b-liu@ti.com: fixed "line over 80 characters" warning]
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-8-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently get "unhandled DISCONNECT transition" warnings from musb core
on device disconnect as things are wrongly set to OTG_STATE_A_IDLE in
host mode when enumerating devices. We can also get "Failed to write reg
index" errors after enumerating.
This is happening at least with cpcap phy where we get multiple ID ground
interrupts. Looks like it's VBUS keeps timing out and needs to be kicked
when the phy sends multiple ID ground interrupts during host mode.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-7-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We can get babble interrupt if we attempt to switch to USB host mode too
soon after enabling musb. Let's fix the issue by waiting a bit in
runtime_resume.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-6-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We currently have musb_set_vbus() called from two different paths. Mostly
it gets called from the USB PHY via omap_musb_set_mailbox(), but in some
cases it can get also called from musb_stage0_irq() rather via .set_vbus:
(musb_set_host [musb_hdrc])
(omap2430_musb_set_vbus [omap2430])
(musb_stage0_irq [musb_hdrc])
(musb_interrupt [musb_hdrc])
(omap2430_musb_interrupt [omap2430])
This is racy and will not work with introducing generic helper functions
for musb_set_host() and musb_set_peripheral(). We want to get rid of the
busy loops in favor of usleep_range().
Let's just get rid of .set_vbus for omap2430 glue layer and let the PHY
code handle VBUS with musb_set_vbus(). Note that in the follow-up patch
we can completely remove omap2430_musb_set_vbus(), but let's do it in a
separate patch as this change may actually turn out to be needed as a
fix.
Reported-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-5-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does not depend directly on the NOP transceiver. It can
compile and work just fine without it.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-4-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order for devicetree nodes to be correctly associated with attached
devices, the controller node needs to be propagated to the glue device.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-3-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Update the function description of musb_stage0_irq() to remove unused
parameter.
Signed-off-by: Saurav Girepunje <saurav.girepunje@gmail.com>
[b-liu@ti.com: revised commit log]
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200115132547.364-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pullup may be already enabled before the driver is initialized. This
happens for instance on JZ4740.
It has to be disabled at init time, as we cannot guarantee that a gadget
driver will be bound to the UDC.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Suggested-by: Bin Liu <b-liu@ti.com>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200107152625.857-3-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When disconnected as USB B-device, suspend interrupt should come before
diconnect interrupt, because the DP/DM pins are shorter than the
VBUS/GND pins on the USB connectors. But we sometimes get a suspend
interrupt after disconnect interrupt. In that case we have devctl set to
99 with VBUS still valid and musb_pm_runtime_check_session() wrongly
thinks we have an active session. We have no other interrupts after
disconnect coming in this case at least with the omap2430 glue.
Let's fix the issue by checking the interrupt status again with
delayed work for the devctl 99 case. In the suspend after disconnect
case the devctl session bit has cleared by then and musb can idle.
For a typical USB B-device connect case we just continue with normal
interrupts.
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: stable@vger.kernel.org
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20200107152625.857-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IRQ handler was passed a pointer to a struct dma_controller, but the
argument was then casted to a pointer to a struct musb_dma_controller.
Fixes: 427c4f3334 ("usb: struct device - replace bus_id with dev_name(), dev_set_name()")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: Artur Rojek <contact@artur-rojek.eu>
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20191216161844.772-2-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Avoid printing any error message if the error code is -EPROBE_DEFER.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20191216162432.1256-1-b-liu@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move musb's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1574232183-5760-1-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now the USB gadget subsystem can use the USB debugfs root directory,
so move dsps's directory from the root of the debugfs filesystem into
the root of usb
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Link: https://lore.kernel.org/r/1573541519-28488-6-git-send-email-chunfeng.yun@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20190904084427.18532-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb core is the only major place in the kernel that checks for
a non-NULL device dma_mask to see if a device is DMA capable. This
is generally a bad idea, as all major busses always set up a DMA mask,
even if the device is not DMA capable - in fact bus layers like PCI
can't even know if a device is DMA capable at enumeration time. This
leads to lots of workaround in HCD drivers, and also prevented us from
setting up a DMA mask for platform devices by default last time we
tried.
Replace this guess with an explicit HCD_DMA that is set by drivers that
appear to have DMA support.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20190816062435.881-4-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platform drivers now have the option to have the platform core create
and remove any needed sysfs attribute files. So take advantage of that
and do not register "by hand" any sysfs files.
Acked-by: Bin Liu <b-liu@ti.com>
Link: https://lore.kernel.org/r/20190805193636.25560-2-gregkh@linuxfoundation.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Variable ret is being initialized with a value that is never read
and ret is being re-assigned a little later on. The assignment is
redundant and hence can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190731223917.16532-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Using dev_get_drvdata directly.
Cc: Bin Liu <b-liu@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fall back to devm_usb_get_phy() if devicetree is not available.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
By registering a generic USB PHY from within the driver, we may shadow
the USB PHY registered by the platform, which might be different.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When enabling ARCH_SUNXI from allnoconfig, SUNXI_SRAM is enabled, but
not REGMAP_MMIO, so the kernel fails to link with an undefined reference
to __devm_regmap_init_mmio_clk. Select REGMAP_MMIO, as suggested in
drivers/base/regmap/Kconfig.
This creates the following dependency loop:
drivers/of/Kconfig:68: symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:63: symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7: symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by SUNXI_SRAM
drivers/soc/sunxi/Kconfig:4: symbol SUNXI_SRAM is selected by USB_MUSB_SUNXI
drivers/usb/musb/Kconfig:63: symbol USB_MUSB_SUNXI depends on GENERIC_PHY
drivers/phy/Kconfig:7: symbol GENERIC_PHY is selected by PHY_BCM_NS_USB3
drivers/phy/broadcom/Kconfig:29: symbol PHY_BCM_NS_USB3 depends on MDIO_BUS
drivers/net/phy/Kconfig:12: symbol MDIO_BUS default is visible depending on PHYLIB
drivers/net/phy/Kconfig:181: symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:18: symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:24: symbol ARC_EMAC depends on OF_IRQ
To fix the circular dependency, make USB_MUSB_SUNXI select GENERIC_PHY
instead of depending on it. This matches the use of GENERIC_PHY by all
but two other drivers.
Cc: <stable@vger.kernel.org> # 4.19
Fixes: 5828729beb ("soc: sunxi: export a regmap for EMAC clock reg on A64")
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
I noticed that musb is blocking core retention for omap4 unlike for
omap3. This is because for omap3 we have phy-twl4030-usb implement
it's own PM runtime to handle errata "VUSB3V1 VBUS overvoltage
debouncer not working when the PHY is powered down". That is done
in order to keep the USB PHY powered when phy-twl4030-usb is loaded.
For the other USB PHYs, we need to enable and disable the PHY based on
musb PM runtime. With the session bit based PM runtime for musb core,
we can now idle the USB PHY always when musb is idle.
Note that adding these calls will not affect the twl4030 driver
as it's phy functions will just query the PHY state without powering
the PHY on or off.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some drivers, like jz4740-musb, don't depend on CONFIG_USB.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch
cases where we are expecting to fall through.
This patch fixes the following warning:
drivers/usb/musb/musb_host.c: In function ‘musb_advance_schedule’:
drivers/usb/musb/musb_host.c:374:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (qh->mux == 1) {
^
drivers/usb/musb/musb_host.c:383:3: note: here
case USB_ENDPOINT_XFER_ISOC:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
Notice that, in this particular case, the code comment is modified
in accordance with what GCC is expecting to find.
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig entry previously depended on USB_OTG_BLACKLIST_HUB
unconditionally, which is an option that is only available when
CONFIG_USB is enabled. However, the USB IP in the JZ4740 SoC does not
support host mode, only gadget mode, so it makes sense to allow it to
build when CONFIG_USB is not set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Depending on MACH_JZ4740 prevent us from creating a generic kernel that
works on more than one MIPS board. Instead, we just depend on MIPS being
set.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for probing the driver from devicetree.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A return statement is indented one level too far, fix this by removing
a tab.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handling short packets (length < max packet size) in the Inventra DMA
engine in the MUSB driver causes the MUSB DMA controller to hang. An
example of a problem that is caused by this problem is when streaming
video out of a UVC gadget, only the first video frame is transferred.
For short packets (mode-0 or mode-1 DMA), MUSB_TXCSR_TXPKTRDY must be
set manually by the driver. This was previously done in musb_g_tx
(musb_gadget.c), but incorrectly (all csr flags were cleared, and only
MUSB_TXCSR_MODE and MUSB_TXCSR_TXPKTRDY were set). Fixing that problem
allows some requests to be transferred correctly, but multiple requests
were often put together in one USB packet, and caused problems if the
packet size was not a multiple of 4. Instead, set MUSB_TXCSR_TXPKTRDY
in dma_controller_irq (musbhsdma.c), just like host mode transfers.
This topic was originally tackled by Nicolas Boichat [0] [1] and is
discussed further at [2] as part of his GSoC project [3].
[0] https://groups.google.com/forum/?hl=en#!topic/beagleboard-gsoc/k8Azwfp75CU
[1] b0be3b6cc1?p=beagleboard-usbsniffer:beagleboard-usbsniffer-kernel.git;a=patch;h=b0be3b6cc195ba732189b04f1d43ec843c3e54c9
[2] http://beagleboard-usbsniffer.blogspot.com/2010/07/musb-isochronous-transfers-fixed.html
[3] http://elinux.org/BeagleBoard/GSoC/USBSniffer
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Signed-off-by: Paul Elder <paul.elder@ideasonboard.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are a few remaining drivers/usb/ files that do not have SPDX
identifiers in them, all of these are either Kconfig or Makefiles. Add
the correct GPL-2.0 identifier to them to make scanning tools happy.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the runtime PM support was added in musb, dsps relies on the timer
calling otg_timer() to activate the usb subsystem. However the driver
doesn't enable the timer for peripheral port, then the peripheral port is
unable to be enumerated by a host if the other usb port is disabled or in
peripheral mode too.
So let's start the timer for peripheral port too.
Fixes: ea2f35c01d ("usb: musb: Fix sleeping function called from invalid context for hdrc glue")
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Due to lack of ID pin interrupt event on AM335x devices, the musb dsps
driver uses polling to detect usb device attach for dual-role port.
But in the case if a micro-A cable adapter is attached without a USB device
attached to the cable, the musb state machine gets stuck in a_wait_vrise
state waiting for the MUSB_CONNECT interrupt which won't happen due to the
usb device is not attached. The state is stuck in a_wait_vrise even after
the micro-A cable is detached, which could cause VBUS retention if then the
dual-role port is attached to a host port.
To fix the problem, make a_wait_vrise as a transient state, then move the
state to either a_wait_bcon for host port or a_idle state for dual-role
port, if no usb device is attached to the port.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TI AM335x CPPI 4.1 module uses a single register bit for CPPI interrupts
in both musb controllers. So disabling the CPPI irq in one musb driver
breaks the other musb module.
Since musb is already disabled before tearing down dma controller in
musb_remove(), it is safe to not disable CPPI irq in
musb_dma_controller_destroy().
Fixes: 255348289f ("usb: musb: dsps: Manage CPPI 4.1 DMA interrupt in DSPS")
Cc: stable@vger.kernel.org
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calling debugfs functions, there is no need to ever check the
return value. The function can work or not, but the code logic should
never do something different based on this.
Because of this, lots of init functions do not need to have return
values, so this cleans up a lot of unused error handling code that never
could have triggered in the past.
Cc: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After the only users of this variable got removed, we now get a
warning about 'otg' being unused:
drivers/usb/musb/da8xx.c: In function 'da8xx_musb_interrupt':
drivers/usb/musb/da8xx.c:226:19: error: unused variable 'otg' [-Werror=unused-variable]
Fixes: d2852f2d3e ("usb: musb: remove references to default_a of struct usb_otg")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UDC core ensures the usb_ep parameter passed in is not NULL, so
checking if (ep != NULL) is pointless.
Convert to_musb_ep() to a simple macro to not directly return NULL to
avoid warnings from code static analysis tools.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The gadget function drivers should ensure the usb_request parameter
passed in is not NULL. UDC core doesn't check if it is NULL, so MUSB
driver shouldn't have to check it either.
Convert to_musb_request() to a simple macro to not directly return NULL
to avoid warnings from code static analysis tools.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To be able to use DSPS-based controllers with device-tree descriptions
of the USB topology, we need to associate the glue device's device-tree
node with the child controller device.
Note that this can also be used to eventually let USB core manage
generic phys.
Also note that the other glue drivers will require similar changes to be
able to describe their buses in DT.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As decided in the discussion [1] we are deleting the otg protocol
support from the musb drivers.
First this patch disables the flags for enabling the otg protocols. We
will later gradually delete the otg protocol code from the musb drivers.
[1] https://www.spinics.net/lists/linux-usb/msg167003.html
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb drivers do not use the otg fsm framework, so referencing to
otg->default_a doesn't have any effect, so remove the references.
But tusb6010 glue driver uses it locally to control the vbus power, so
keep the references in tusb6010 only.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_stage0_irq() is 400+ lines long. Break its interrupt events
handling into each individual functions to make it easy to read.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following members in struct musb_hdrc_config are not used,
so remove them.
soft_con
utm_16
big_endian
mult_bulk_tx
mult_bulk_rx
high_iso_tx
high_iso_rx
dma
dma_channels
dyn_fifo_size
vendor_ctrl
vendor_stat
vendor_req
dma_req_chan
musb_hdrc_eps_bits
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
include/linux/usb/musb.h already defines enum for musb port mode, so
remove the duplicate in musb_core.h and use the definition in musb.h.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_core already has musb_get_mode(), so remove the duplicate from
musb_dsps.c.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both musb_io and musb_platform_ops in struct musb define a quirks flag
for the same purpose. Let's remove the one in struct musb_io, and use
that in struct musb_platform_ops instead.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following wrappers were defined because of Blackfin support. Now
Blackfin support is removed, these wrappers are no longer needed, so
remove them.
musb_write_txfifosz
musb_write_txfifoadd
musb_write_rxfifosz
musb_write_rxfifoadd
musb_write_ulpi_buscontrol
musb_read_txfifosz
musb_read_txfifoadd
musb_read_rxfifosz
musb_read_rxfifoadd
musb_read_ulpi_buscontrol
musb_read_hwvers
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, nobody uses adjust_channel_params() any
more, so remove it from struct musb_platform_ops.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, we no longer need function pointers for
musb_readl() and musb_writel().
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now Blackfin support is removed, header musbhsdma.h is only included in
musbhsdma.c. So let's merge the content in musbhsdma.h to musbhsdma.c
and delete musbhsdma.h.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed that writing 0xF2 to the power register while it
reads as 0xF4 results in the register having the value 0xF0, i.e. clearing
RESUME and setting SUSPENDM in one go does not work. It might also violate
the USB spec to transition directly from resume to suspend, especially
when not taking T_DRSMDN into account. But this is what happens when a
remote wakeup occurs between SetPortFeature USB_PORT_FEAT_SUSPEND on the
root hub and musb_bus_suspend being called.
This commit returns -EBUSY when musb_bus_suspend is called while remote
wakeup is signalled and thus avoids to reset the RESUME bit. Ignoring
this error when musb_port_suspend is called from musb_hub_control is ok.
Signed-off-by: Daniel Glöckner <dg@emlix.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_request pointer could be NULL in musb_g_tx(), where the
tracepoint call would trigger the NULL pointer dereference failure when
parsing the members of the usb_request pointer.
Move the tracepoint call to where the usb_request pointer is already
checked to solve the issue.
Fixes: fc78003e53 ("usb: musb: gadget: add usb-request tracepoints")
Cc: stable@vger.kernel.org # v4.8+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb_start_urb() doesn't check the pass-in parameter if it is NULL. But
in musb_bulk_nak_timeout() the parameter passed to musb_start_urb() is
returned from first_qh(), which could be NULL.
So wrap the musb_start_urb() call here with a if condition check to
avoid the potential NULL pointer dereference.
Fixes: f283862f3b ("usb: musb: NAK timeout scheme on bulk TX endpoint")
Cc: stable@vger.kernel.org # v3.7+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This resolves the merge issue with drivers/usb/core/hcd.c
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 39cee200c2 ("usb: musb: core: call init and shutdown for
the usb phy") the musb USB phy is initialised by musb_core, but the
original initialisation in the dsps-glue init callback was left in
place resulting in two calls to phy init during probe (and similarly,
two shutdowns on remove).
Drop the duplicate phy init and shutdown calls from the dsps glue in
favour of the ones in musb core, which other glue drivers rely on.
Note however that any generic phy is still initialised in the glue init
callback (just as for the other drivers).
Cc: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Johan Hovold <johan@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Set the new HCD flag which prevents USB core from trying to manage our
phys.
This is needed to be able to associate the controller platform device
with the glue device device-tree node on the BBB which uses legacy USB
phys. Otherwise, the generic phy lookup in usb_phy_roothub_init() and
thus HCD registration fails repeatedly with -EPROBE_DEFER (see commit
178a0bce05 ("usb: core: hcd: integrate the PHY wrapper into the HCD
core")).
Note that a related phy-lookup issue was recently worked around in the
phy core by commit b7563e2796 ("phy: work around 'phys' references to
usb-nop-xceiv devices"). Something similar may now be needed for other
USB phys, and in particular if we eventually want to let USB core manage
musb generic phys.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for non-DT systems, which hasn't been used by a mainline
kernel since commit 9080b8dc76 ("ARM: OMAP2+: Remove legacy usb-host.c
platform init code"). Specifically, since that commit usb_get_phy_dev()
have always returned -ENODEV when looking up a legacy phy, something
which in turn would have led to the init callback returning
-EPROBE_DEFER indefinitely.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and PHY driver patches for 4.17-rc1.
Lots of USB typeC work happened this round, with code moving from the
staging directory into the "real" part of the kernel, as well as new
infrastructure being added to be able to handle the different types of
"roles" that typeC requires.
There is also the normal huge set of USB gadget controller and driver
updates, along with XHCI changes, and a raft of other tiny fixes all
over the USB tree. And the PHY driver updates are merged in here as
well as they interacted with the USB drivers in some places.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWsSpJw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ylGawCdED2xS3HUxOIqfh81d8B1py8ji04AoJXdLAsH
JgwXbdbibZBabYTVi5s5
=LrRH
-----END PGP SIGNATURE-----
Merge tag 'usb-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver patches for 4.17-rc1.
Lots of USB typeC work happened this round, with code moving from the
staging directory into the "real" part of the kernel, as well as new
infrastructure being added to be able to handle the different types of
"roles" that typeC requires.
There is also the normal huge set of USB gadget controller and driver
updates, along with XHCI changes, and a raft of other tiny fixes all
over the USB tree. And the PHY driver updates are merged in here as
well as they interacted with the USB drivers in some places.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (250 commits)
Revert "USB: serial: ftdi_sio: add Id for Physik Instrumente E-870"
usb: musb: gadget: misplaced out of bounds check
usb: chipidea: imx: Fix ULPI on imx53
usb: chipidea: imx: Cleanup ci_hdrc_imx_platform_flag
usb: chipidea: usbmisc: small clean up
usb: chipidea: usbmisc: evdo can be set e/o reset
usb: chipidea: usbmisc: evdo is only specific to OTG port
USB: serial: ftdi_sio: add Id for Physik Instrumente E-870
usb: dwc3: gadget: never call ->complete() from ->ep_queue()
usb: gadget: udc: core: update usb_ep_queue() documentation
usb: host: Remove the deprecated ATH79 USB host config options
usb: roles: Fix return value check in intel_xhci_usb_probe()
USB: gadget: f_midi: fixing a possible double-free in f_midi
usb: core: Add USB_QUIRK_DELAY_CTRL_MSG to usbcore quirks
usb: core: Copy parameter string correctly and remove superfluous null check
USB: announce bcdDevice as well as idVendor, idProduct.
USB:fix USB3 devices behind USB3 hubs not resuming at hibernate thaw
usb: hub: Reduce warning to notice on power loss
USB: serial: ftdi_sio: add support for Harman FirmwareHubEmulator
USB: serial: cp210x: add ELDAT Easywave RX09 id
...
This removes the entire architecture code for blackfin, cris, frv, m32r,
metag, mn10300, score, and tile, including the associated device drivers.
I have been working with the (former) maintainers for each one to ensure
that my interpretation was right and the code is definitely unused in
mainline kernels. Many had fond memories of working on the respective
ports to start with and getting them included in upstream, but also saw
no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company
in charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It seems
that all the SoC product lines are still around, but have not used the
custom CPU architectures for several years at this point. In contrast,
CPU instruction sets that remain popular and have actively maintained
kernel ports tend to all be used across multiple licensees.
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I made
sure that they are all unused. Some architectures (notably tile, mn10300,
and blackfin) are still being shipped in products with old kernels,
but those products will never be updated to newer kernel releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing their
support or getting it added to mainline gcc in the first place.
They all have patched gcc-7.3 ports that work to some degree, but
complete upstream support won't happen before gcc-8.1. Csky posted
their first kernel patch set last week, their situation will be similar.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=fQ8z
-----END PGP SIGNATURE-----
Merge tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic
Pul removal of obsolete architecture ports from Arnd Bergmann:
"This removes the entire architecture code for blackfin, cris, frv,
m32r, metag, mn10300, score, and tile, including the associated device
drivers.
I have been working with the (former) maintainers for each one to
ensure that my interpretation was right and the code is definitely
unused in mainline kernels. Many had fond memories of working on the
respective ports to start with and getting them included in upstream,
but also saw no point in keeping the port alive without any users.
In the end, it seems that while the eight architectures are extremely
different, they all suffered the same fate: There was one company in
charge of an SoC line, a CPU microarchitecture and a software
ecosystem, which was more costly than licensing newer off-the-shelf
CPU cores from a third party (typically ARM, MIPS, or RISC-V). It
seems that all the SoC product lines are still around, but have not
used the custom CPU architectures for several years at this point. In
contrast, CPU instruction sets that remain popular and have actively
maintained kernel ports tend to all be used across multiple licensees.
[ See the new nds32 port merged in the previous commit for the next
generation of "one company in charge of an SoC line, a CPU
microarchitecture and a software ecosystem" - Linus ]
The removal came out of a discussion that is now documented at
https://lwn.net/Articles/748074/. Unlike the original plans, I'm not
marking any ports as deprecated but remove them all at once after I
made sure that they are all unused. Some architectures (notably tile,
mn10300, and blackfin) are still being shipped in products with old
kernels, but those products will never be updated to newer kernel
releases.
After this series, we still have a few architectures without mainline
gcc support:
- unicore32 and hexagon both have very outdated gcc releases, but the
maintainers promised to work on providing something newer. At least
in case of hexagon, this will only be llvm, not gcc.
- openrisc, risc-v and nds32 are still in the process of finishing
their support or getting it added to mainline gcc in the first
place. They all have patched gcc-7.3 ports that work to some
degree, but complete upstream support won't happen before gcc-8.1.
Csky posted their first kernel patch set last week, their situation
will be similar
[ Palmer Dabbelt points out that RISC-V support is in mainline gcc
since gcc-7, although gcc-7.3.0 is the recommended minimum - Linus ]"
This really says it all:
2498 files changed, 95 insertions(+), 467668 deletions(-)
* tag 'arch-removal' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/asm-generic: (74 commits)
MAINTAINERS: UNICORE32: Change email account
staging: iio: remove iio-trig-bfin-timer driver
tty: hvc: remove tile driver
tty: remove bfin_jtag_comm and hvc_bfin_jtag drivers
serial: remove tile uart driver
serial: remove m32r_sio driver
serial: remove blackfin drivers
serial: remove cris/etrax uart drivers
usb: Remove Blackfin references in USB support
usb: isp1362: remove blackfin arch glue
usb: musb: remove blackfin port
usb: host: remove tilegx platform glue
pwm: remove pwm-bfin driver
i2c: remove bfin-twi driver
spi: remove blackfin related host drivers
watchdog: remove bfin_wdt driver
can: remove bfin_can driver
mmc: remove bfin_sdh driver
input: misc: remove blackfin rotary driver
input: keyboard: remove bf54x driver
...
musb->endpoints[] has array size MUSB_C_NUM_EPS.
We must check array bounds before accessing the array and not afterwards.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: Bin Liu <b-liu@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The blackfin architecture is getting removed, so we can clean up
all the special cases in the musb driver.
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Aaron Wu <aaron.wu@analog.com>
Acked-by: Bin Liu <b-liu@ti.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
[arnd: adding in fixups from Aaron and Stephen]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
A lot of Kconfig symbols have architecture specific dependencies.
In those cases that depend on architectures we have already removed,
they can be omitted.
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This fixes an oops on unbind / module unload (on the musb omap2430
platform).
musb_remove function now calls musb_platform_exit before disabling
runtime pm.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
...instead of open coding file operations followed by custom ->open()
callbacks per each attribute.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without pm_runtime_{get,put}_sync calls in place, reading
vbus status via /sys causes the following error:
Unhandled fault: external abort on non-linefetch (0x1028) at 0xfa0ab060
pgd = b333e822
[fa0ab060] *pgd=48011452(bad)
[<c05261b0>] (musb_default_readb) from [<c0525bd0>] (musb_vbus_show+0x58/0xe4)
[<c0525bd0>] (musb_vbus_show) from [<c04c0148>] (dev_attr_show+0x20/0x44)
[<c04c0148>] (dev_attr_show) from [<c0259f74>] (sysfs_kf_seq_show+0x80/0xdc)
[<c0259f74>] (sysfs_kf_seq_show) from [<c0210bac>] (seq_read+0x250/0x448)
[<c0210bac>] (seq_read) from [<c01edb40>] (__vfs_read+0x1c/0x118)
[<c01edb40>] (__vfs_read) from [<c01edccc>] (vfs_read+0x90/0x144)
[<c01edccc>] (vfs_read) from [<c01ee1d0>] (SyS_read+0x3c/0x74)
[<c01ee1d0>] (SyS_read) from [<c0106fe0>] (ret_fast_syscall+0x0/0x54)
Solution was suggested by Tony Lindgren <tony@atomide.com>.
Signed-off-by: Merlijn Wajer <merlijn@wizzup.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
On dm3730 there are enumeration problems after resume.
Investigation led to the cause that the MUSB_POWER_SOFTCONN
bit is not set. If it was set before suspend (because it
was enabled via musb_pullup()), it is set in
musb_restore_context() so the pullup is enabled. But then
musb_start() is called which overwrites MUSB_POWER and
therefore disables MUSB_POWER_SOFTCONN, so no pullup is
enabled and the device is not enumerated.
So let's do a subset of what musb_start() does
in the same way as musb_suspend() does it. Platform-specific
stuff it still called as there might be some phy-related stuff
which needs to be enabled.
Also interrupts are enabled, as it was the original idea
of calling musb_start() in musb_resume() according to
Commit 6fc6f4b87c ("usb: musb: Disable interrupts on suspend,
enable them on resume")
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It really should be DEVICE_ATTR_WO(), no need to "open code" it.
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of "open coding" a DEVICE_ATTR() define, use the
DEVICE_ATTR_RW() macro instead, which does everything properly instead.
This does require a few static functions to be renamed to work properly,
but thanks to a script from Joe Perches, this was easily done.
Reported-by: Joe Perches <joe@perches.com>
Cc: Matthieu CASTET <castet.matthieu@free.fr>
Cc: Stanislaw Gruszka <stf_xl@wp.pl>
Cc: Peter Chen <Peter.Chen@nxp.com>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is only one clock for the DA8xx MUSB device, so we don't need the
con_id, so remove it. This way we don't have to add an unnecessary
property to the device tree bindings for the clock.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix the following build warning:
drivers/usb/musb/musb_host.c:1809:8: warning: variable 'pipe' set but not used [-Wunused-but-set-variable]
by removing the pipe variable in musb_host_rx()
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fix the following warning
drivers/usb/musb/musb_host.c:223:8: warning: variable 'frame' set but not used [-Wunused-but-set-variable]
by remove the frame variable in musb_start_urb().
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When babble condition happens, the musb controller might automatically
turns off VBUS. On DA8xx platform, the controller generates drvvbus
interrupt for turning off VBUS along with the babble interrupt.
In this case, we should handle the babble interrupt first and recover
from the babble condition.
This change ignores the drvvbus interrupt if babble interrupt is also
generated at the same time, so the babble recovery routine works
properly.
Cc: stable@vger.kernel.org # v3.16+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along with
phy and chipidea enhancements. There's also a lot of SPDX tags and
license boilerplate cleanups as well, which provide some churn in the
diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see happen.
All of these have been in linux-next with no reported issues for a
while.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgm/Vw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yktXwCdGgpInfOEvOGFd83EPDL7a1ncyc4AoM5wI8yl
1CeLipqVIN3IsMMJptvb
=zvDI
-----END PGP SIGNATURE-----
Merge tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/PHY updates from Greg KH:
"Here is the big set of USB and PHY driver updates for 4.15-rc1.
There is the usual amount of gadget and xhci driver updates, along
with phy and chipidea enhancements. There's also a lot of SPDX tags
and license boilerplate cleanups as well, which provide some churn in
the diffstat.
Other major thing is the typec code that moved out of staging and into
the "real" part of the drivers/usb/ tree, which was nice to see
happen.
All of these have been in linux-next with no reported issues for a
while"
* tag 'usb-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (263 commits)
usb: gadget: f_fs: Fix use-after-free in ffs_free_inst
USB: usbfs: compute urb->actual_length for isochronous
usb: core: message: remember to reset 'ret' to 0 when necessary
USB: typec: Remove remaining redundant license text
USB: typec: add SPDX identifiers to some files
USB: renesas_usbhs: rcar?.h: add SPDX tags
USB: chipidea: ci_hdrc_tegra.c: add SPDX line
USB: host: xhci-debugfs: add SPDX lines
USB: add SPDX identifiers to all remaining Makefiles
usb: host: isp1362-hcd: remove a couple of redundant assignments
USB: adutux: remove redundant variable minor
usb: core: add a new usb_get_ptm_status() helper
usb: core: add a 'type' parameter to usb_get_status()
usb: core: introduce a new usb_get_std_status() helper
usb: core: rename usb_get_status() 'type' argument to 'recip'
usb: core: add Status Type definitions
USB: gadget: Remove redundant license text
USB: gadget: function: Remove redundant license text
USB: gadget: udc: Remove redundant license text
USB: gadget: legacy: Remove redundant license text
...
Now that the SPDX tag is in all USB files, that identifies the license
in a specific and legally-defined manner. So the extra GPL text wording
can be removed as it is no longer needed at all.
This is done on a quest to remove the 700+ different ways that files in
the kernel describe the GPL license text. And there's unneeded stuff
like the address (sometimes incorrect) for the FSF which is never
needed.
No copyright headers or other non-license-description text was removed.
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's good to have SPDX identifiers in all files to make it easier to
audit the kernel tree for correct licenses.
Update the drivers/usb/ and include/linux/usb* files with the correct
SPDX license identifier based on the license text in the file itself.
The SPDX identifier is a legally binding shorthand, which can be used
instead of the full boiler plate text.
This work is based on a script and data from Thomas Gleixner, Philippe
Ombredanne, and Kate Stewart.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Acked-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now struct musb has the timer (dev_timer) for glue drivers, so let's
remove the duplicated timer defined in dsps glue driver, and use
dev_timer defined in struct musb.
Signed-off-by: Bin Liu <b-liu@ti.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Instead of a per-device static timer variable, a spare timer "dev_timer"
is added to the musb structure for devices to use for their per-device
timer.
Cc: linux-usb@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Addresses-Coverity-ID: 1397608
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is some registers defined in da8xx.c though they are not used.
These registers are also defined and used in musb_cppi41.c
Remove these defines from da8xx.c.
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes a kernel oops when unloading the driver due to usb_put_phy
being called after usb_phy_generic_unregister when the device is
detached. Calling usb_phy_generic_unregister causes x->dev->driver to
be NULL in usb_put_phy and results in a NULL pointer dereference.
Cc: stable@vger.kernel.org # v4.3+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi musb has a bug where sometimes it will generate a babble
error on device disconnect instead of a disconnect IRQ. When this
happens the musb controller switches from host mode to device mode
(it clears MUSB_DEVCTL_HM/MUSB_DEVCTL_SESSION and sets
MUSB_DEVCTL_BDEVICE) and gets stuck in this state.
The babble error is misdetected as a bus reset because MUSB_DEVCTL_HM
was cleared.
To fix this, use is_host_active() rather than (devctl & MUSB_DEVCTL_HM)
to detect babble error so that sunxi musb babble recovery can handle it
by restoring the mode. This information is provided by the driver logic
and does not rely on register contents.
Cc: stable@vger.kernel.org # v4.1+
Signed-off-by: Jonathan Liu <net147@gmail.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the number of channels is set to 15 but in the case of DA8xx,
the number of channels is 4.
Update the driver to configure the number of channels at runtime.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The way to configure the DMA mode on DA8xx is different from DSPS.
Add a new function to configure DMA mode on DA8xx and use a callback
to call the right function based on the platform.
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The DA8xx and DSPS platforms don't use the same address for few registers.
On Da8xx, this is causing some issues (e.g. teardown that doesn't work).
Configure the address of the register during the init and use them instead
of constants.
Cc: stable@vger.kernel.org # v4.12+
Reported-by: nsekhar@ti.com
Signed-off-by: Alexandre Bailon <abailon@baylibre.com>
Tested-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb delayed irq work was never flushed on suspend, something which
since 4.9 can lead to an external abort if the work is scheduled after
the grandparent's clock has been disabled:
PM: Suspending system (mem)
PM: suspend of devices complete after 125.224 msecs
PM: suspend devices took 0.132 seconds
PM: late suspend of devices complete after 7.423 msecs
PM: noirq suspend of devices complete after 7.083 msecs
suspend debug: Waiting for 5 second(s).
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd0262c60
...
[<c054880c>] (musb_default_readb) from [<c0547b5c>] (musb_irq_work+0x48/0x220)
[<c0547b5c>] (musb_irq_work) from [<c014f8a4>] (process_one_work+0x1f4/0x758)
[<c014f8a4>] (process_one_work) from [<c014fe5c>] (worker_thread+0x54/0x514)
[<c014fe5c>] (worker_thread) from [<c015704c>] (kthread+0x128/0x158)
[<c015704c>] (kthread) from [<c0109330>] (ret_from_fork+0x14/0x24)
Commit 2bff3916fd ("usb: musb: Fix PM for hub disconnect") started
scheduling musb_irq_work with a delay of up to a second and with
retries thereby making this easy to trigger, for example, by suspending
shortly after a disconnect.
Note that we set a flag to prevent the irq work from rescheduling itself
during suspend and instead process a disconnect immediately. This takes
care of the case where we are disconnected shortly before suspending.
However, when in host mode, a disconnect while suspended will still
go unnoticed and thus prevent the controller from runtime suspending
upon resume as the session bit is always set. This will need to be
addressed separately.
Fixes: 550a7375fe ("USB: Add MUSB and TUSB support")
Fixes: 467d5c9807 ("usb: musb: Implement session bit based runtime PM for musb-core")
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Felipe Balbi <felipe.balbi@linux.intel.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The current session-bit quirk implementation does not prevent the retry
counter from underflowing, something which could break runtime PM and
keep the device active for a very long time (about 2^32 seconds) after a
disconnect.
This notably breaks the B-device timeout case, but could potentially
cause problems also when the controller is operating as an A-device.
Fixes: 2bff3916fd ("usb: musb: Fix PM for hub disconnect")
Cc: stable <stable@vger.kernel.org> # 4.9
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The musb_dsps driver is special in that the parent (glue) device's
driver is accessing registers mapped by the child. The clock is however
shared and is managed by the grandparent device.
Since commit 869c597829 ("usb: musb: dsps: add support for suspend and
resume") the dsps driver has been accessing these registers as part of
suspend and resume.
The parent driver obviously cannot runtime resume the child during
system suspend and is currently relying on the fact that the child will
be RPM_ACTIVE throughout suspend. The suspend implementation also makes
sure to check that the child is indeed present (and hence the clock
enabled) before accessing the registers.
Let's add an explicit runtime resume of the glue device itself to enable
the clock before doing the register accesses in case these assumptions ever
change (i.e. if the child is left runtime suspended).
Note that the glue-timer cancellation is moved after the child-presence
check to keep error handling simple. This should be fine as the timer is
not setup until the controller is being registered and at that time
glue->musb and its driver data have already been initialised.
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that the controller is runtime resumed when system suspending
to avoid an external abort when accessing the interrupt registers:
Unhandled fault: external abort on non-linefetch (0x1008) at 0xd025840a
...
[<c05481a4>] (musb_default_readb) from [<c0545abc>] (musb_disable_interrupts+0x84/0xa8)
[<c0545abc>] (musb_disable_interrupts) from [<c0546b08>] (musb_suspend+0x38/0xb8)
[<c0546b08>] (musb_suspend) from [<c04a57f8>] (platform_pm_suspend+0x3c/0x64)
This is easily reproduced on a BBB by enabling the peripheral port only
(as the host port may enable the shared clock) and keeping it
disconnected so that the controller is runtime suspended. (Well, you
would also need to the not-yet-merged am33xx-suspend patches by Dave
Gerlach to be able to suspend the BBB.)
This is a regression that was introduced by commit 1c4d0b4e18 ("usb:
musb: Remove pm_runtime_set_irq_safe") which allowed the parent glue
device to runtime suspend and thereby exposed a couple of older issues:
Register accesses without explicitly making sure the controller is
runtime resumed during suspend was first introduced by commit c338412b5d
("usb: musb: unconditionally save and restore the context on suspend")
in 3.14.
Commit a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on
resume") later started setting the RPM status to active during resume,
and this was also implicitly relying on the parent always being active.
Since commit 71723f9546 ("PM / runtime: print error when activating a
child to unactive parent") this now also results in the following
warning:
musb-hdrc musb-hdrc.0: runtime PM trying to activate child device
musb-hdrc.0 but parent (47401400.usb) is not active
This patch has been verified on 4.13-rc2, 4.12 and 4.9 using a BBB
(the dsps glue would always be active also in 4.8).
Fixes: c338412b5d ("usb: musb: unconditionally save and restore the context on suspend")
Fixes: a1fc1920aa ("usb: musb: core: make sure musb is in RPM_ACTIVE on resume")
Fixes: 1c4d0b4e18 ("usb: musb: Remove pm_runtime_set_irq_safe")
Cc: stable <stable@vger.kernel.org> # 4.8+
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Daniel Mack <zonque@gmail.com>
Cc: Dave Gerlach <d-gerlach@ti.com>
Cc: Rafael J. Wysocki <rjw@rjwysocki.net>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The fifo memory allocation in mode_2_cfg[] doesn't utilize all the 4KB
memory.
Increse some endpoint fifo buffers to fully use all the 4KB memory. Now
we can support more webcam usecases on DA8xx.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tony Lindgren