Here are the USB-serial updates for 5.13-rc1, including:
- better type detection for pl2303
- support for more line speeds for pl2303 (TA/TB)
- fixed CSIZE handling for the new xr driver
- core support for multi-interface functions
- TIOCGSERIAL and TIOCSSERIAL fixes
- generic TIOCSSERIAL support (e.g. for closing_wait)
- fixed return value for unsupported ioctls
- support for gpio valid masks in cp210x
- drain-delay fixes and improvements
- support for multi-port devices for xr
- generalisation of the xr driver to support three new device classes
(XR21B142X, XR21B1411 and XR2280X)
Included are also various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYIE2iwAKCRALxc3C7H1l
CFJsAQCd6rX6VyteR6RUmmTjmGDyRwxsXGniw9bf36dzhlKncwEAga2E+47FGHYm
YiNQzfcETfjGO21usS1BWhNvzf/gsgs=
=1FU1
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.13-rc1
Here are the USB-serial updates for 5.13-rc1, including:
- better type detection for pl2303
- support for more line speeds for pl2303 (TA/TB)
- fixed CSIZE handling for the new xr driver
- core support for multi-interface functions
- TIOCGSERIAL and TIOCSSERIAL fixes
- generic TIOCSSERIAL support (e.g. for closing_wait)
- fixed return value for unsupported ioctls
- support for gpio valid masks in cp210x
- drain-delay fixes and improvements
- support for multi-port devices for xr
- generalisation of the xr driver to support three new device classes
(XR21B142X, XR21B1411 and XR2280X)
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.13-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (72 commits)
USB: cdc-acm: add more Maxlinear/Exar models to ignore list
USB: serial: xr: add copyright notice
USB: serial: xr: reset FIFOs on open
USB: serial: xr: add support for XR22801, XR22802, XR22804
USB: serial: xr: add support for XR21B1411
USB: serial: xr: add support for XR21B1421, XR21B1422 and XR21B1424
USB: serial: xr: add type abstraction
USB: serial: xr: drop type prefix from shared defines
USB: serial: xr: move pin configuration to probe
USB: serial: xr: rename GPIO-pin defines
USB: serial: xr: rename GPIO-mode defines
USB: serial: xr: add support for XR21V1412 and XR21V1414
USB: serial: ti_usb_3410_5052: clean up termios CSIZE handling
USB: serial: ti_usb_3410_5052: use kernel types consistently
USB: serial: ti_usb_3410_5052: add port-command helpers
USB: serial: ti_usb_3410_5052: clean up vendor-request helpers
USB: serial: ti_usb_3410_5052: drop unnecessary packed attributes
USB: serial: io_ti: drop unnecessary packed attributes
USB: serial: io_ti: use kernel types consistently
USB: serial: io_ti: add read-port-command helper
...
suspend() does its poisoning conditionally, resume() does it
unconditionally. On a device with combined interfaces this
will balance, on a device with two interfaces the counter will
go negative and resubmission will fail.
Both actions need to be done conditionally.
Fixes: 6069e3e927 ("USB: cdc-acm: untangle a circular dependency between callback and softint")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210421074513.4327-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the xr_serial got support for other models, add their USB IDs
as well.
The Maxlinear/Exar USB UARTs can be used in either ACM mode using the
cdc-acm driver or in "custom driver" mode in which further features such
as hardware and software flow control, GPIO control and in-band
line-status reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
correctly.
Ensure that cdc_acm will not bind to these devices if the custom
USB-serial driver is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/5155887a764cbc11f8da0217fe08a24a77d120b4.1616571453.git.mchehab+huawei@kernel.org
[ johan: rewrite commit message, clean up entries ]
Cc: Oliver Neukum <oneukum@suse.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
The xmit_fifo_size parameter could be used to set the hardware transmit
fifo size of a legacy UART when it could not be detected, but the
interface is limited to eight bits and should be left unset when it is
not used.
Similarly, baud_base could be used to set the UART base clock when it
could not be detected, but might as well be left unset when it is not
known (which is the case for CDC).
Fix the cdc-acm TIOCGSERIAL implementation by dropping its custom
interpretation of the unused xmit_fifo_size and baud_base fields, which
overflowed the former with the URB buffer size and set the latter to the
current line speed. Also return the port line number, which is the only
other value used besides the close parameters.
Note that the current line speed can still be retrieved through the
standard termios interfaces.
Fixes: 18c75720e6 ("USB: allow users to run setserial with cdc-acm")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TIOCSSERIAL is a horrid, underspecified, legacy interface which for most
serial devices is only useful for setting the close_delay and
closing_wait parameters.
A non-privileged user has only ever been able to set the since long
deprecated ASYNC_SPD flags and trying to change any other *supported*
feature should result in -EPERM being returned. Setting the current
values for any supported features should return success.
Fix the cdc-acm implementation which instead indicated that the
TIOCSSERIAL ioctl was not even implemented when a non-privileged user
set the current values.
Fixes: ba2d8ce9db ("cdc-acm: implement TIOCSSERIAL to avoid blocking close(2)")
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit b401f8c4f4.
The offending commit claimed that trying to set the values reported back
by TIOCGSERIAL as a regular user could result in an -EPERM error when HZ
is 250, but that was never the case.
With HZ=250, the default 0.5 second value of close_delay is converted to
125 jiffies when set and is converted back to 50 centiseconds by
TIOCGSERIAL as expected (not 12 cs as was claimed, even if that was the
case before an earlier fix).
Comparing the internal current and new jiffies values is just fine to
determine if the value is about to change so drop the bogus workaround
(which was also backported to stable).
For completeness: With different default values for these parameters or
with a HZ value not divisible by two, the lack of rounding when setting
the default values in tty_port_init() could result in an -EPERM being
returned, but this is hardly something we need to worry about.
Cc: Anthony Mallet <anthony.mallet@laas.fr>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210408131602.27956-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not log the successful-probe message until the tty device has been
registered.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-9-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure to always claim the data interface and bail out if binding
fails.
Note that the driver had a check to verify that the data interface was
not already bound to a driver but would not detect other failures (e.g.
if the interface was not authorised).
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-8-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use negation consistently throughout the driver for NULL checks.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-7-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Name the probe error labels after what they do rather than using
sequence numbers which is harder to review and maintain (e.g. may
require renaming unrelated labels when a label is added or removed).
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-6-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's no need to clear the interface driver data on failed probe (and
driver core will clear it anyway).
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The interface driver data has already been set by
usb_driver_claim_interface() so drop the redundant subsequent
assignment.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If tty-device registration fails the driver would fail to release the
data interface. When the device is later disconnected, the disconnect
callback would still be called for the data interface and would go about
releasing already freed resources.
Fixes: c93d819550 ("usb: cdc-acm: fix error handling in acm_probe()")
Cc: stable@vger.kernel.org # 3.9
Cc: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If tty-device registration fails the driver copy of any Country
Selection functional descriptor would end up being freed twice; first
explicitly in the error path and then again in the tty-port destructor.
Drop the first erroneous free that was left when fixing a tty-port
resource leak.
Fixes: cae2bc768d ("usb: cdc-acm: Decrement tty port's refcount if probe() fail")
Cc: stable@vger.kernel.org # 4.19
Cc: Jaejoong Kim <climbbb.kim@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210322155318.9837-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This failure is so common that logging an error here amounts
to spamming log files.
Reviewed-by: Bruno Thomsen <bruno.thomsen@gmail.com>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210311130126.15972-2-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Counting break events is nice but we should actually report them to
the tty layer.
Fixes: 5a6a62bdb9 ("cdc-acm: add TIOCMIWAIT")
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20210311133714.31881-1-oneukum@suse.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Apparently an application that opens a device and calls select()
on it, will hang if the decice is disconnected. It's a little
surprising that we had this bug for 15 years, but apparently
nobody ever uses select() with a printer: only write() and read(),
and those work fine. Well, you can also select() with a timeout.
The fix is modeled after devio.c. A few other drivers check the
condition first, then do not add the wait queue in case the
device is disconnected. We doubt that's completely race-free.
So, this patch adds the process first, then locks properly
and checks for the disconnect.
Reviewed-by: Zqiang <qiang.zhang@windriver.com>
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210303221053.1cf3313e@suzdal.zaitcev.lan
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The CDC ACM driver is false matching the Goodix Fingerprint device
against the USB_CDC_ACM_PROTO_AT_V25TER.
The Goodix Fingerprint device is a biometrics sensor that should be
handled in user-space. libfprint has some support for Goodix
fingerprint sensors, although not for this particular one. It is
possible that the vendor allocates a PID per OEM (Lenovo, Dell etc).
If this happens to be the case then more devices from the same vendor
could potentially match the ACM modem module table.
Signed-off-by: Yorick de Wid <ydewid@gmail.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210213144901.53199-1-ydewid@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are the USB-serial updates for 5.12-rc1, including:
- a line-speed fix for newer pl2303 devices
- a line-speed fix for FTDI FT-X devices
- a new xr_serial driver for MaxLinear/Exar devices (non-ACM mode)
- a cdc-acm blacklist entry for when the xr_serial driver is enabled
- cp210x support for software flow control
- various cp210x modem-control fixes
- an updated ZTE P685M modem entry to stop claiming the QMI interface
- an update to drop the port_remove() driver-callback return value
Included are also various clean ups.
All have been in linux-next with no reported issues.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQHbPq+cpGvN/peuzMLxc3C7H1lCAUCYCPxBQAKCRALxc3C7H1l
CP1iAQCRn7/4ulkGXgSjVL2o8TfGAQRhvxL14qtzysOyPLwgrAD6ApuJdPRHnetL
q0TDaRqnXqVTV6uUfoSC5eVEF4dS/Qs=
=5ZLn
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-5.12-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-next
Johan writes:
USB-serial updates for 5.12-rc1
Here are the USB-serial updates for 5.12-rc1, including:
- a line-speed fix for newer pl2303 devices
- a line-speed fix for FTDI FT-X devices
- a new xr_serial driver for MaxLinear/Exar devices (non-ACM mode)
- a cdc-acm blacklist entry for when the xr_serial driver is enabled
- cp210x support for software flow control
- various cp210x modem-control fixes
- an updated ZTE P685M modem entry to stop claiming the QMI interface
- an update to drop the port_remove() driver-callback return value
Included are also various clean ups.
All have been in linux-next with no reported issues.
* tag 'usb-serial-5.12-rc1' of https://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial: (41 commits)
USB: serial: drop bogus to_usb_serial_port() checks
USB: serial: make remove callback return void
USB: serial: drop if with an always false condition
USB: serial: option: update interface mapping for ZTE P685M
USB: serial: ftdi_sio: restore divisor-encoding comments
USB: serial: ftdi_sio: fix FTX sub-integer prescaler
USB: serial: cp210x: clean up auto-RTS handling
USB: serial: cp210x: fix RTS handling
USB: serial: cp210x: clean up printk zero padding
USB: serial: cp210x: clean up flow-control debug message
USB: serial: cp210x: drop shift macros
USB: serial: cp210x: fix modem-control handling
USB: serial: cp210x: suppress modem-control errors
USB: serial: mos7720: fix error code in mos7720_write()
USB: serial: xr: fix B0 handling
USB: serial: xr: fix pin configuration
USB: serial: xr: fix gpio-mode handling
USB: serial: xr: simplify line-speed logic
USB: serial: xr: clean up line-settings handling
USB: serial: xr: document vendor-request recipient
...
Some devices, such as the Winbond Electronics Corp. Virtual Com Port
(Vendor=0416, ProdId=5011), lockup when usb_set_interface() or
usb_clear_halt() are called. This device has only a single
altsetting, so it should not be necessary to call usb_set_interface().
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Jeremy Figgins <kernel@jeremyfiggins.com>
Link: https://lore.kernel.org/r/YAy9kJhM/rG8EQXC@watson
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Exar XR21V141X can be used in either ACM mode using the cdc-acm
driver or in "custom driver" mode in which further features such as
hardware and software flow control, GPIO control and in-band line-status
reporting are available.
In ACM mode the device always enables RTS/CTS flow control, something
which could prevent transmission in case the CTS input isn't wired up
correctly.
Ensure that cdc_acm will not bind to the device if the custom USB-serial
driver is enabled.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Manivannan Sadhasivam <mani@kernel.org>
Link: https://lore.kernel.org/r/20201122170822.21715-4-mani@kernel.org
[ johan: rewrite commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Stack-allocated buffers cannot be used for DMA (on all architectures).
Replace the HP-channel macro with a helper function that allocates a
dedicated transfer buffer so that it can continue to be used with
arguments from the stack.
Note that the buffer is cleared on allocation as usblp_ctrl_msg()
returns success also on short transfers (the buffer is only used for
debugging).
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210104145302.2087-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The previous patches in this series have changed the behaviour of the
driver and added new calls.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-5-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new ioctl only returns the status byte (STB) that was originally
sent by the device due to a service request (SRQ) condition.
This ioctl checks the srq_asserted bit of the associated file
descriptor. If set, the srq_asserted bit is reset and the cached
STB with original SRQ information is returned. Otherwise the ioctl
returns the error code ENOMSG.
This ioctl is useful to support non USBTMC-488 compliant devices.
Time sensitive applications can read the cached STB without incurring
the cost of an urb transaction over the bus.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-4-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This new ioctl reads the status byte (STB) from the device and returns
the STB unmodified to the application. The srq_asserted bit is not taken
into account and not changed.
This ioctl is useful to support non USBTMC-488 compliant devices.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-3-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ioctl USBTMC488_IOCTL_READ_STB either returns a cached status byte
(STB) sent by the device due to a service request (SRQ) condition or
the STB obtained from a query to the device with a READ_STATUS_BYTE
control message.
When the query is interrupted by an SRQ message on the interrupt pipe,
the ioctl still returns the requested STB while the STB of the
out-of-band SRQ message is cached for the next call of this
ioctl. However the cached SRQ STB represents a state that was previous
to the last returned STB. Furthermore the cached SRQ STB can be stale
and not reflect the current state of the device.
The fixed ioctl now always reads the STB from the device and if the
associated file descriptor has the srq_asserted bit set it ors in the
RQS bit to the returned STB and clears the srq_asserted bit conformant
to subclass USB488 devices.
Tested-by: Jian-Wei Wu <jian-wei_wu@keysight.com>
Reviewed-by: Guido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: Dave Penkler <dpenkler@gmail.com>
Link: https://lore.kernel.org/r/20201215155621.9592-2-dpenkler@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting UAF at usb_submit_urb() [1], for
service_outstanding_interrupt() is not checking WDM_DISCONNECTING
before calling usb_submit_urb(). Close the race by doing same checks
wdm_read() does upon retry.
Also, while wdm_read() checks WDM_DISCONNECTING with desc->rlock held,
service_interrupt_work() does not hold desc->rlock. Thus, it is possible
that usb_submit_urb() is called from service_outstanding_interrupt() from
service_interrupt_work() after WDM_DISCONNECTING was set and kill_urbs()
from wdm_disconnect() completed. Thus, move kill_urbs() in
wdm_disconnect() to after cancel_work_sync() (which makes sure that
service_interrupt_work() is no longer running) completed.
Although it seems to be safe to dereference desc->intf->dev in
service_outstanding_interrupt() even if WDM_DISCONNECTING was already set
because desc->rlock or cancel_work_sync() prevents wdm_disconnect() from
reaching list_del() before service_outstanding_interrupt() completes,
let's not emit error message if WDM_DISCONNECTING is set by
wdm_disconnect() while usb_submit_urb() is in progress.
[1] https://syzkaller.appspot.com/bug?extid=9e04e2df4a32fb661daf
Reported-by: syzbot <syzbot+9e04e2df4a32fb661daf@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/620e2ee0-b9a3-dbda-a25b-a93e0ed03ec5@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This device is supported by the IR Toy driver.
Reported-by: Georgi Bakalski <georgi.bakalski@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201227134502.4548-2-sean@mess.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Renesas R-Car and RZ/G SoCs have a firmware download mode over USB.
However, on reset a banner string is transmitted out which is not expected
to be echoed back and will corrupt the protocol.
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Link: https://lore.kernel.org/r/20201111131209.3977903-1-chris.brandt@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit a4e7279cd1 ("cdc-acm: introduce a cool down") is causing
regression if there is some USB error, such as -EPROTO.
This has been reported on some samples of the Odroid-N2 using the Combee II
Zibgee USB dongle.
> struct acm *acm = container_of(work, struct acm, work)
is incorrect in case of a delayed work and causes warnings, usually from
the workqueue:
> WARNING: CPU: 0 PID: 0 at kernel/workqueue.c:1474 __queue_work+0x480/0x528.
When this happens, USB eventually stops working completely after a while.
Also the ACM_ERROR_DELAY bit is never set, so the cooldown mechanism
previously introduced cannot be triggered and acm_submit_read_urb() is
never called.
This changes makes the cdc-acm driver use a single delayed work, fixing the
pointer arithmetic in acm_softint() and set the ACM_ERROR_DELAY when the
cooldown mechanism appear to be needed.
Fixes: a4e7279cd1 ("cdc-acm: introduce a cool down")
Cc: Oliver Neukum <oneukum@suse.com>
Reported-by: Pascal Vizeli <pascal.vizeli@nabucasa.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Link: https://lore.kernel.org/r/20201019170702.150534-1-jbrunet@baylibre.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting hung task at wdm_flush() [1], for there is a circular
dependency that wdm_flush() from flip_close() for /dev/cdc-wdm0 forever
waits for /dev/raw-gadget to be closed while close() for /dev/raw-gadget
cannot be called unless close() for /dev/cdc-wdm0 completes.
Tetsuo Handa considered that such circular dependency is an usage error [2]
which corresponds to an unresponding broken hardware [3]. But Alan Stern
responded that we should be prepared for such hardware [4]. Therefore,
this patch changes wdm_flush() to use wait_event_interruptible_timeout()
which gives up after 30 seconds, for hardware that remains silent must be
ignored. The 30 seconds are coming out of thin air.
Changing wait_event() to wait_event_interruptible_timeout() makes error
reporting from close() syscall less reliable. To compensate it, this patch
also implements wdm_fsync() which does not use timeout. Those who want to
be very sure that data has gone out to the device are now advised to call
fsync(), with a caveat that fsync() can return -EINVAL when running on
older kernels which do not implement wdm_fsync().
This patch also fixes three more problems (listed below) found during
exhaustive discussion and testing.
Since multiple threads can concurrently call wdm_write()/wdm_flush(),
we need to use wake_up_all() whenever clearing WDM_IN_USE in order to
make sure that all waiters are woken up. Also, error reporting needs
to use fetch-and-clear approach in order not to report same error for
multiple times.
Since wdm_flush() checks WDM_DISCONNECTING, wdm_write() should as well
check WDM_DISCONNECTING.
In wdm_flush(), since locks are not held, it is not safe to dereference
desc->intf after checking that WDM_DISCONNECTING is not set [5]. Thus,
remove dev_err() from wdm_flush().
[1] https://syzkaller.appspot.com/bug?id=e7b761593b23eb50855b9ea31e3be5472b711186
[2] https://lkml.kernel.org/r/27b7545e-8f41-10b8-7c02-e35a08eb1611@i-love.sakura.ne.jp
[3] https://lkml.kernel.org/r/79ba410f-e0ef-2465-b94f-6b9a4a82adf5@i-love.sakura.ne.jp
[4] https://lkml.kernel.org/r/20200530011040.GB12419@rowland.harvard.edu
[5] https://lkml.kernel.org/r/c85331fc-874c-6e46-a77f-0ef1dc075308@i-love.sakura.ne.jp
Reported-by: syzbot <syzbot+854768b99f19e89d7f81@syzkaller.appspotmail.com>
Cc: stable <stable@vger.kernel.org>
Co-developed-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Link: https://lore.kernel.org/r/20200928141755.3476-1-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For interfaces that lack a union descriptor, probe for a
"combined-interface" before falling back to the call-management
descriptor instead of the other way round.
This allows for the removal of the NO_DATA_INTERFACE quirk and makes the
probe algorithm somewhat easier to follow.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-5-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the data-class define provided by USB core and drop the
driver-specific one.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-4-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Handle broken union functional descriptors where the master-interface
doesn't exist or where its class is of neither Communication or Data
type (as required by the specification) by falling back to
"combined-interface" probing.
Note that this still allows for handling union descriptors with switched
interfaces.
This specifically makes the Whistler radio scanners TRX series devices
work with the driver without adding further quirks to the device-id
table.
Reported-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Tested-by: Daniel Caujolle-Bert <f1rmb.daniel@gmail.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This reverts commit 2ad9d544f2.
Drop bogus sanity check; an interface in the active configuration will
always have a current altsetting assigned by USB core.
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20200921135951.24045-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Buffers should be u8*, not unsigned char*
Buffers have an unsigned length and using an int
as a boolean is a bit outdated.
No functional change intended.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200917110235.11854-1-oneukum@suse.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clang static analysis reports this error
cdc-acm.c:409:3: warning: Use of memory after it is freed
acm_process_notification(acm, (unsigned char *)dr);
There are three problems, the first one is that dr is not reset
The variable dr is set with
if (acm->nb_index)
dr = (struct usb_cdc_notification *)acm->notification_buffer;
But if the notification_buffer is too small it is resized with
if (acm->nb_size) {
kfree(acm->notification_buffer);
acm->nb_size = 0;
}
alloc_size = roundup_pow_of_two(expected_size);
/*
* kmalloc ensures a valid notification_buffer after a
* use of kfree in case the previous allocation was too
* small. Final freeing is done on disconnect.
*/
acm->notification_buffer =
kmalloc(alloc_size, GFP_ATOMIC);
dr should point to the new acm->notification_buffer.
The second problem is any data in the notification_buffer is lost
when the pointer is freed. In the normal case, the current data
is accumulated in the notification_buffer here.
memcpy(&acm->notification_buffer[acm->nb_index],
urb->transfer_buffer, copy_size);
When a resize happens, anything before
notification_buffer[acm->nb_index] is garbage.
The third problem is the acm->nb_index is not reset on a
resizing buffer error.
So switch resizing to using krealloc and reassign dr and
reset nb_index.
Fixes: ea2583529c ("cdc-acm: reassemble fragmented notifications")
Signed-off-by: Tom Rix <trix@redhat.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200801152154.20683-1-trix@redhat.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----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=SYqr
-----END PGP SIGNATURE-----
Merge tag 'media/v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Legacy soc_camera driver was removed from staging
- New I2C sensor related drivers: dw9768, ch7322, max9271, rdacm20
- TI vpe driver code was re-organized and had new features added
- Added Xilinx MIPI CSI-2 Rx Subsystem driver
- Added support for Infrared Toy and IR Droid devices
- Lots of random driver fixes, new features and cleanups
* tag 'media/v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (318 commits)
media: camss: fix memory leaks on error handling paths in probe
media: davinci: vpif_capture: fix potential double free
media: radio: remove redundant assignment to variable retval
media: allegro: fix potential null dereference on header
media: mtk-mdp: Fix a refcounting bug on error in init
media: allegro: fix an error pointer vs NULL check
media: meye: fix missing pm_mchip_mode field
media: cafe-driver: use generic power management
media: saa7164: use generic power management
media: v4l2-dev/ioctl: Fix document for VIDIOC_QUERYCAP
media: v4l2: Correct kernel-doc inconsistency
media: v4l2: Correct kernel-doc inconsistency
media: dvbdev.h: keep * together with the type
media: v4l2-subdev.h: keep * together with the type
media: videobuf2: Print videobuf2 buffer state by name
media: colorspaces-details.rst: fix V4L2_COLORSPACE_JPEG description
media: tw68: use generic power management
media: meye: use generic power management
media: cx88: use generic power management
media: cx25821: use generic power management
...
A good attempt was made to document everything else.
Fixes the following W=1 kernel build warning(s):
drivers/usb/class/cdc-wdm.c:961: warning: Function parameter or member 'manage_power' not described in 'usb_cdc_wdm_register'
Cc: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200715093209.3165641-6-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Demote usbtmc's file header to a standard comment block.
Fixes the following W=1 kernel build warning(s):
drivers/usb/class/usbtmc.c:11: warning: Function parameter or member 'fmt' not described in 'pr_fmt'
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20200702144625.2533530-30-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IR Droid / IR Toy device used custom protocol over serial
line, so it is presenting itself as CDC ACM device.
Now that we have proper in-kernel driver for it we need to black-list the
device in cdc-acm driver.
http://dangerousprototypes.com/docs/USB_Infrared_Toyhttps://www.irdroid.com/irdroid-usb-ir-transceiver/
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
USB_DEVICE(0x0424, 0x274e) can send data before cdc_acm is ready,
causing garbage chars on the TTY causing stray input to the shell
and/or login prompt.
Signed-off-by: Joakim Tjernlund <joakim.tjernlund@infinera.com>
Cc: stable@vger.kernel.org
Acked-by: Oliver Neukum <oneukum@suse.com>
Link: https://lore.kernel.org/r/20200605105418.22263-1-joakim.tjernlund@infinera.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 84af7a6194 ("checkpatch: kconfig: prefer 'help' over
'---help---'"), the number of '---help---' has been gradually
decreasing, but there are still more than 2400 instances.
This commit finishes the conversion. While I touched the lines,
I also fixed the indentation.
There are a variety of indentation styles found.
a) 4 spaces + '---help---'
b) 7 spaces + '---help---'
c) 8 spaces + '---help---'
d) 1 space + 1 tab + '---help---'
e) 1 tab + '---help---' (correct indentation)
f) 1 tab + 1 space + '---help---'
g) 1 tab + 2 spaces + '---help---'
In order to convert all of them to 1 tab + 'help', I ran the
following commend:
$ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/'
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Greg Kroah-Hartman