This patch adds support for lvds backlight on boards
i.MX6q-SabreSD and i.MX6dl-SabreSD
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Currently we get the following errors on imx51-babbage:
/display@di0: could not find display-timings node
/display@di0: no timings specified
/display@di1: could not find display-timings node
/display@di1: no timings specified
imx-drm imx-drm: failed to allocate buffer with size 0
Provide timing values for IPU1, which is connected to a DVI bridge and
to IPU2, which can be connected to the WVGA panel, so that both of them can
be functional.
While at it, disable the WVGA panel, so that DVI output becomes the default one.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On the mx53qsb board with mc34708 PMIC, GPIO1_8 resets the system, so better not
to use it as a wakeup source.
Use GPIO 2_14 and 2_15 for wakeup sources instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
SDHC1 does not have any GPIO for reading the card detection status, so
remove 'cd-gpios'.
After this change card detection works via the internal SD controller mechanism.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
SDHC3 is 8 bit-wide, so pass the bus-width property to reflect that.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This board is based on the M28 SoM with custom baseboard. Supported
are LEDs, ethernet, PWM, LCD, SD slots.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
GPIO3_29 is used to reset the ethernet phy.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
GPIO1_25 is used to reset the ethernet phy.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
MX6QDL_PAD_EIM_D23__GPIO3_IO23 pin is used to reset the ethernet phy.
Add it to the 'hog' group.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For more information about the Udoo board:
http://www.udoo.org/
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Add initial PHYTEC VF610 Cosmic/Cosmic+ board support with
UART and FEC enabled.
Signed-off-by: Matt Porter <matt.porter@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This pin definition had been added after the initial patch to use
symbolic pin names in DTS files.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Update the Ka-Ro TX28 DTS file.
- add Copyright header
- use label references for better readability
- sort the entries alphabetically
- add some aliases used by U-Boot to modify the DT data
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
For some reason, the select input of pin function USB_OTG_ID is not
implemented via a regular select input register but using the bit
USB_OTG_ID_ SEL (shift 13) of IOMUXC_GPR1 register (offset 0x4).
As per the workaround for such quirk implemented in pinctrl driver,
we need to compose the input_val cell as below.
31 23 15 7 0
| 0xff | shift | width | select |
Thus, we have 0xff0d0100 for MX6QDL_PAD_ENET_RX_ER__USB_OTG_ID and
0xff0d0101 for MX6QDL_PAD_GPIO_1__USB_OTG_ID in input_val cell.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Convert mx23/mx28 dts files to use the padconfig defintions from
mxs-pinfunc.h.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Convert mx23/mx28 dts filed to use the pinctrl header files.
NOTE: During automatic conversion of these files to use the pinconfig
definitions an inconsistency has been found in:
arch/arm/boot/dts/imx28-apx4devkit.dts
According to the comment the function for pad SSP2_SS0 should have
been MX28_PAD_SSP2_SS0__GPIO_2_19, while the given value 0x2131
represents: MX28_PAD_SSP2_SS0__AUART3_TX
I used the later (though probably wrong) definition because that's
what is actually being used in the DTB.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Remove the list of possible pin configurations from the documentation
file and create header files containing those definitions.
This eliminates the need for error-prone manual lookup of those values
in the documentation and guarantees consistency between the human
readable representation of the pad function in the .dts file and the
actual binary value used in DT.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Provide 'lradc-touchscreen-wires' property to the LRADC driver, so that
touchscreen can be functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
On imx6qdl-sabresd the SDHC2 and SDHC3 are 8 bit-wide, so pass the bus-width
property to reflect that.
Otherwise the mmc driver will operate with the default bus-width value of 4.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
This is needed for supporting ultra high speed cards like SD3.0 cards.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Enable USB function for OTG 1 and OTG 2 at mx6sololite evk.
Besides, fix the wrong interrupt number for OTG2 and host 1.
Signed-off-by: Peter Chen <peter.chen@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
imx6q-sabrelite board can be connected to a 1024x768 Hannstar LVDS panel.
Add support for it.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Put the nodes in alphabetical order so that further node additions can be better
organized.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Trying to use the usb otg port on mx53qsb results in the following error:
$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 52:0f:8a:1e:aa:09
usb0: MAC de:f3:70:d8:6c:62
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
(Connect the USB cable)
$ ci_hdrc ci_hdrc.0: remove, state 4
usb usb1: USB disconnect, device number 1
ci_hdrc ci_hdrc.0: USB bus 1 deregistered
ci_hdrc ci_hdrc.0: timeout waiting for 00000800 in 11
USB otg port goes to connector J3 (mini USB) and also to the USB combo (J2).
As mx53qsb does not provide a USB ID pin, pass the dr_mode as 'peripheral' so
that we can have usb device working.
Tested via g_ether.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Tested via g_ether:
$ modprobe g_ether
using random self ethernet address
using random host ethernet address
usb0: HOST MAC 42:b5:26:a9:48:21
usb0: MAC 36:a6:85:9b:9e:13
using random self ethernet address
using random host ethernet address
g_ether gadget: Ethernet Gadget, version: Memorial Day 2008
g_ether gadget: g_ether ready
$ g_ether gadget: high-speed config #1: CDC Ethernet (ECM)
$ ifconfig usb0 10.0.0.2
Then on the PC host side:
~$ sudo ifconfig usb0 10.0.0.1
~$ ping 10.0.0.2
PING 10.0.0.2 (10.0.0.2) 56(84) bytes of data.
64 bytes from 10.0.0.2: icmp_req=1 ttl=64 time=1.26 ms
64 bytes from 10.0.0.2: icmp_req=2 ttl=64 time=0.280 ms
64 bytes from 10.0.0.2: icmp_req=3 ttl=64 time=0.297 ms
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
RTS/CTS pins can be used for different purposes, so create separate
definitions for these pins.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
1) Four fixes for cpufreq regressions introduced by the changes that
removed Device Tree parsing for CPU device nodes from cpufreq
drivers from Sudeep KarkadaNagesha.
2) Two fixes for recent cpufreq regressions introduced by changes
related to the preservation of sysfs attributes over system
suspend/resume cycles from Viresh Kumar.
3) Fix for ACPI-based wakeup signaling in the PCI subsystem that
fails to stop PME polling for devices put into the D3cold power
state from Rafael J Wysocki.
4) Fix for bad interactions between cpufreq and udev on systems
supporting intel_pstate where acpi-cpufreq is available as well
from Yinghai Lu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8EeE
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
1) Four fixes for cpufreq regressions introduced by the changes that
removed Device Tree parsing for CPU device nodes from cpufreq
drivers from Sudeep KarkadaNagesha.
2) Two fixes for recent cpufreq regressions introduced by changes
related to the preservation of sysfs attributes over system
suspend/resume cycles from Viresh Kumar.
3) Fix for ACPI-based wakeup signaling in the PCI subsystem that
fails to stop PME polling for devices put into the D3cold power
state from Rafael J Wysocki.
4) Fix for bad interactions between cpufreq and udev on systems
supporting intel_pstate where acpi-cpufreq is available as well
from Yinghai Lu.
* tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: return EEXIST instead of EBUSY for second registering
PCI / ACPI / PM: Clear pme_poll for devices in D3cold on wakeup
ARM: shmobile: change dev_id to cpu0 while registering cpu clock
ARM: i.MX: change dev_id to cpu0 while registering cpu clock
cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 device
cpufreq: cpufreq-cpu0: assign cpu_dev correctly to cpu0 device
cpufreq: unlock correct rwsem while updating policy->cpu
cpufreq: Clear policy->cpus bits in __cpufreq_remove_dev_finish()
- Documentation clarification on tagged pointers
- hwcap widened to 64-bit (user space already reading it as 64-bit)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)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=OICB
-----END PGP SIGNATURE-----
Merge tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull ARM64 fixes from Catalin Marinas:
- Compat register fault reporting fix
- Documentation clarification on tagged pointers
- hwcap widened to 64-bit (user space already reading it as 64-bit)
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Widen hwcap to be 64 bit
arm64: Correctly report LR and SP for compat tasks
arm64: documentation: tighten up tagged pointer documentation
arm64: Make do_bad_area() function static
Under arm64 elf_hwcap is a 32 bit quantity, but it is stored in
a 64 bit auxiliary ELF field and glibc reads hwcap as 64 bit.
This patch widens elf_hwcap to be 64 bit.
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When a task crashes and we print debugging information, ensure that
compat tasks show the actual AArch32 LR and SP registers rather than the
AArch64 ones.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
A set of fixes for ARM platforms for 3.12. Among them:
- A fix for build breakage in the MTD subsystem for some PXA devices.
David Woodhouse has this patch in his for-next branch but has not been
responding to our requests to send it up so here it is.
I should have amended the commit message to describe the build failure for
CONFIG_OF=n setups, but forgot and now it's down in the stack of commits.
- Added device-tree for the BeagleBone Black. Turns out people have been
using the older "regualar" bone DT for the newer boards, and there's
risk of damaging hardware that way.
- Misc DT and regular fixes for OMAP.
- Fix to make the ST-Ericsson "snowball" boards boot with
multi_v7_defconfig, and enable one of the ST-E reference boards on the
same config.
- Kconfig cleanup for u300 to hide submenus when the platform isn't
enabled.
- Enable ARM_ATAG_DTB_COMPAT to let firmware override command
line when booting with an appended devicetree on non-DT-enabled
firmware (needed to boot snowball).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=I14p
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes for ARM platforms for 3.12. Among them:
- A fix for build breakage in the MTD subsystem for some PXA devices.
David Woodhouse has this patch in his for-next branch but has not
been responding to our requests to send it up so here it is. I
should have amended the commit message to describe the build
failure for CONFIG_OF=n setups, but forgot and now it's down in the
stack of commits.
- Added device-tree for the BeagleBone Black. Turns out people have
been using the older "regualar" bone DT for the newer boards, and
there's risk of damaging hardware that way.
- Misc DT and regular fixes for OMAP.
- Fix to make the ST-Ericsson "snowball" boards boot with
multi_v7_defconfig, and enable one of the ST-E reference boards on
the same config.
- Kconfig cleanup for u300 to hide submenus when the platform isn't
enabled.
- Enable ARM_ATAG_DTB_COMPAT to let firmware override command line
when booting with an appended devicetree on non-DT-enabled firmware
(needed to boot snowball)"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: multi_v7: add HREFv60 to multi_v7 defconfig
ARM: OMAP2+: mux: fix trivial typo in name
ARM: OMAP4 SMP: Corrected a typo fucntions to functions
ARM: OMAP4: cpuidle: fix: call cpu_cluster_pm_exit conditionally
mailbox: remove unnecessary platform_set_drvdata()
ARM: mach-omap2: gpmc: Fix warning when CONFIG_ARM_LPAE=y
ARM: OMAP: fix return value check in omap_device_build_from_dt()
ARM: OMAP4: Fix clock_get error for GPMC during boot
ARM: sa1100: collie.c: fall back to jedec_probe flash detection
ARM: u300: hide submenus
ARM: dts: igep00x0: Add pinmux configuration for MCBSP2
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for blaze
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for pandaboard
mtd: nand: pxa3xx: Remove unneeded ifdef CONFIG_OF
ARM: multi_v7_defconfig: enable ARM_ATAG_DTB_COMPAT
ARM: ux500: disable outer cache debug
ARM: dts: OMAP5: fix ocp2scp DTS data
ARM: dts: OMAP5: fix reg property size
ARM: dts: am335x-bone*: add DT for BeagleBone Black
ARM: dts: omap3-beagle-xm: fix string error in compatible property
...
Pull MIPS updates from Ralf Baechle:
- Minor updates and fixes to the Octeon ethernet driver in staging
- A fix to VGA_MAP_MEM() for 64 bit platforms
- Fix a workaround for 74K/1074K processors
- The symlink arch/mips/boot/dts/include/dt-bindings was pointing to a
a file with a name ending in \n. I think this may have been caused
by a git bug with with patches sent by email
- A build fix for VGA console on BCM1480-based systems
- Fix PCI device access via "/sys/bus/pci/.../resource0" or similar
work for Alchemy platforms
- Fix potential data leak on MIPS R5 cores. This doesn't add proper
support for any R5 features, just ensures a kernel without such
support will be secure to run
- Adding a macros for the CP0 Config5 register to be used by the R5 fix
- Make get_cycles() actually return something useful where possible
This also requires a preparatory patch for performance sake
- Fix a warning about the use of smp_processor_id() in preemptible
code. Again this includes a preparatory patch adding the
infrastructure to be used by the actual patch
- Finally remove pointless one-line comment
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix invalid symbolic link file
MIPS: PCI: pci-bcm1480: Include missing vt.h header
MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.
MIPS: Add MIPS R5 config5 register.
MIPS: PCI: Use pci_resource_to_user to map pci memory space properly
MIPS: 74K/1074K: Correct erratum workaround.
MIPS: Cleanup CP0 PRId and CP1 FPIR register access masks
MIPS: Remove useless comment about kprobe from arch/mips/Makefile
MIPS: Fix VGA_MAP_MEM macro.
MIPS: Reimplement get_cycles().
MIPS: Optimize current_cpu_type() for better code.
MIPS: Fix accessing to per-cpu data when flushing the cache
MIPS: Provide nice way to access boot CPU's data.
staging: octeon-ethernet: rgmii: enable interrupts that we can handle
staging: octeon-ethernet: remove skb alloc failure warnings
staging: octeon-ethernet: make dropped packets to consume NAPI budget
It's needed for the MAX_NR_CONSOLES macro.
Fixes the following build problem on a randconfig:
arch/mips/pci/pci-bcm1480.c: In function 'bcm1480_pcibios_init':
arch/mips/pci/pci-bcm1480.c:261:36: error: 'MAX_NR_CONSOLES'
undeclared (first use in this function)
arch/mips/pci/pci-bcm1480.c:261:36: note: each undeclared
identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-bcm1480.o] Error 1
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5858/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently the kernel will always use the FR=0 register model for O32. If
an O32 application did enable FR=1 mode, some data from another application
might be leaked in the extra registers becoming visible.
Iow, this patch is meant to make the kernel MIPS R5 tolerant but leaves
proper MIPS R5 support to a future patchset.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Dong Aisheng