Instead of allocating a single unused biovec for discard requests, send
them down without any payload. Instead we allow the driver to add a
"special" payload using a biovec embedded into struct request (unioned
over other fields never used while in the driver), and overloading
the number of segments for this case.
This has a couple of advantages:
- we don't have to allocate the bio_vec
- the amount of special casing for discard requests in the block
layer is significantly reduced
- using this same scheme for other request types is trivial,
which will be important for implementing the new WRITE_ZEROES
op on devices where it actually requires a payload (e.g. SCSI)
- we can get rid of playing games with the request length, as
we'll never touch it and completions will work just fine
- it will allow us to support ranged discard operations in the
future by merging non-contiguous discard bios into a single
request
- last but not least it removes a lot of code
This patch is the common base for my WIP series for ranges discards and to
remove discard_zeroes_data in favor of always using REQ_OP_WRITE_ZEROES,
so it would be good to get it in quickly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Factor out common code for setting REQ_NOMERGE flag which is being used
out at certain places and make it a helper instead, req_set_nomerge().
Signed-off-by: Ritesh Harjani <riteshh@codeaurora.org>
Get rid of the inline.
Signed-off-by: Jens Axboe <axboe@fb.com>
This adds a new block layer operation to zero out a range of
LBAs. This allows to implement zeroing for devices that don't use
either discard with a predictable zero pattern or WRITE SAME of zeroes.
The prominent example of that is NVMe with the Write Zeroes command,
but in the future, this should also help with improving the way
zeroing discards work. For this operation, suitable entry is exported in
sysfs which indicate the number of maximum bytes allowed in one
write zeroes operation by the device.
Signed-off-by: Chaitanya Kulkarni <chaitanya.kulkarni@hgst.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
A lot of the REQ_* flags are only used on struct requests, and only of
use to the block layer and a few drivers that dig into struct request
internals.
This patch adds a new req_flags_t rq_flags field to struct request for
them, and thus dramatically shrinks the number of common requests. It
also removes the unfortunate situation where we have to fit the fields
from the same enum into 32 bits for struct bio and 64 bits for
struct request.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Shaun Tancheff <shaun.tancheff@seagate.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
After arbitrary bio size was introduced, the incoming bio may
be very big. We have to split the bio into small bios so that
each holds at most BIO_MAX_PAGES bvecs for safety reason, such
as bio_clone().
This patch fixes the following kernel crash:
> [ 172.660142] BUG: unable to handle kernel NULL pointer dereference at 0000000000000028
> [ 172.660229] IP: [<ffffffff811e53b4>] bio_trim+0xf/0x2a
> [ 172.660289] PGD 7faf3e067 PUD 7f9279067 PMD 0
> [ 172.660399] Oops: 0000 [#1] SMP
> [...]
> [ 172.664780] Call Trace:
> [ 172.664813] [<ffffffffa007f3be>] ? raid1_make_request+0x2e8/0xad7 [raid1]
> [ 172.664846] [<ffffffff811f07da>] ? blk_queue_split+0x377/0x3d4
> [ 172.664880] [<ffffffffa005fb5f>] ? md_make_request+0xf6/0x1e9 [md_mod]
> [ 172.664912] [<ffffffff811eb860>] ? generic_make_request+0xb5/0x155
> [ 172.664947] [<ffffffffa0445c89>] ? prio_io+0x85/0x95 [bcache]
> [ 172.664981] [<ffffffffa0448252>] ? register_cache_set+0x355/0x8d0 [bcache]
> [ 172.665016] [<ffffffffa04497d3>] ? register_bcache+0x1006/0x1174 [bcache]
The issue can be reproduced by the following steps:
- create one raid1 over two virtio-blk
- build bcache device over the above raid1 and another cache device
and bucket size is set as 2Mbytes
- set cache mode as writeback
- run random write over ext4 on the bcache device
Fixes: 54efd50(block: make generic_make_request handle arbitrarily sized bios)
Reported-by: Sebastian Roesner <sroesner-kernelorg@roesner-online.de>
Reported-by: Eric Wheeler <bcache@lists.ewheeler.net>
Cc: stable@vger.kernel.org (4.3+)
Cc: Shaohua Li <shli@fb.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 288dab8a35 ("block: add a separate operation type for secure
erase") split REQ_OP_SECURE_ERASE from REQ_OP_DISCARD without considering
all the places REQ_OP_DISCARD was being used to mean either. Fix those.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Fixes: 288dab8a35 ("block: add a separate operation type for secure erase")
Signed-off-by: Jens Axboe <axboe@fb.com>
Since commit 63a4cc2486, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block driver updates from Jens Axboe:
"This branch also contains core changes. I've come to the conclusion
that from 4.9 and forward, I'll be doing just a single branch. We
often have dependencies between core and drivers, and it's hard to
always split them up appropriately without pulling core into drivers
when that happens.
That said, this contains:
- separate secure erase type for the core block layer, from
Christoph.
- set of discard fixes, from Christoph.
- bio shrinking fixes from Christoph, as a followup up to the
op/flags change in the core branch.
- map and append request fixes from Christoph.
- NVMeF (NVMe over Fabrics) code from Christoph. This is pretty
exciting!
- nvme-loop fixes from Arnd.
- removal of ->driverfs_dev from Dan, after providing a
device_add_disk() helper.
- bcache fixes from Bhaktipriya and Yijing.
- cdrom subchannel read fix from Vchannaiah.
- set of lightnvm updates from Wenwei, Matias, Johannes, and Javier.
- set of drbd updates and fixes from Fabian, Lars, and Philipp.
- mg_disk error path fix from Bart.
- user notification for failed device add for loop, from Minfei.
- NVMe in general:
+ NVMe delay quirk from Guilherme.
+ SR-IOV support and command retry limits from Keith.
+ fix for memory-less NUMA node from Masayoshi.
+ use UINT_MAX for discard sectors, from Minfei.
+ cancel IO fixes from Ming.
+ don't allocate unused major, from Neil.
+ error code fixup from Dan.
+ use constants for PSDT/FUSE from James.
+ variable init fix from Jay.
+ fabrics fixes from Ming, Sagi, and Wei.
+ various fixes"
* 'for-4.8/drivers' of git://git.kernel.dk/linux-block: (115 commits)
nvme/pci: Provide SR-IOV support
nvme: initialize variable before logical OR'ing it
block: unexport various bio mapping helpers
scsi/osd: open code blk_make_request
target: stop using blk_make_request
block: simplify and export blk_rq_append_bio
block: ensure bios return from blk_get_request are properly initialized
virtio_blk: use blk_rq_map_kern
memstick: don't allow REQ_TYPE_BLOCK_PC requests
block: shrink bio size again
block: simplify and cleanup bvec pool handling
block: get rid of bio_rw and READA
block: don't ignore -EOPNOTSUPP blkdev_issue_write_same
block: introduce BLKDEV_DISCARD_ZERO to fix zeroout
NVMe: don't allocate unused nvme_major
nvme: avoid crashes when node 0 is memoryless node.
nvme: Limit command retries
loop: Make user notify for adding loop device failed
nvme-loop: fix nvme-loop Kconfig dependencies
nvmet: fix return value check in nvmet_subsys_alloc()
...
For a front merge, the maximum number of sectors of the
request must be checked against the front merge BIO sector,
not the current sector of the request.
Signed-off-by: Damien Le Moal <damien.lemoal@hgst.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Before merging a bio into an existing request, io scheduler is called to
get its approval first. However, the requests that come from a plug
flush may get merged by block layer without consulting with io
scheduler.
In case of CFQ, this can cause fairness problems. For instance, if a
request gets merged into a low weight cgroup's request, high weight cgroup
now will depend on low weight cgroup to get scheduled. If high weigt cgroup
needs that io request to complete before submitting more requests, then it
will also lose its timeslice.
Following script demonstrates the problem. Group g1 has a low weight, g2
and g3 have equal high weights but g2's requests are adjacent to g1's
requests so they are subject to merging. Due to these merges, g2 gets
poor disk time allocation.
cat > cfq-merge-repro.sh << "EOF"
#!/bin/bash
set -e
IO_ROOT=/mnt-cgroup/io
mkdir -p $IO_ROOT
if ! mount | grep -qw $IO_ROOT; then
mount -t cgroup none -oblkio $IO_ROOT
fi
cd $IO_ROOT
for i in g1 g2 g3; do
if [ -d $i ]; then
rmdir $i
fi
done
mkdir g1 && echo 10 > g1/blkio.weight
mkdir g2 && echo 495 > g2/blkio.weight
mkdir g3 && echo 495 > g3/blkio.weight
RUNTIME=10
(echo $BASHPID > g1/cgroup.procs &&
fio --readonly --name name1 --filename /dev/sdb \
--rw read --size 64k --bs 64k --time_based \
--runtime=$RUNTIME --offset=0k &> /dev/null)&
(echo $BASHPID > g2/cgroup.procs &&
fio --readonly --name name1 --filename /dev/sdb \
--rw read --size 64k --bs 64k --time_based \
--runtime=$RUNTIME --offset=64k &> /dev/null)&
(echo $BASHPID > g3/cgroup.procs &&
fio --readonly --name name1 --filename /dev/sdb \
--rw read --size 64k --bs 64k --time_based \
--runtime=$RUNTIME --offset=256k &> /dev/null)&
sleep $((RUNTIME+1))
for i in g1 g2 g3; do
echo ---- $i ----
cat $i/blkio.time
done
EOF
# ./cfq-merge-repro.sh
---- g1 ----
8:16 162
---- g2 ----
8:16 165
---- g3 ----
8:16 686
After applying the patch:
# ./cfq-merge-repro.sh
---- g1 ----
8:16 90
---- g2 ----
8:16 445
---- g3 ----
8:16 471
Signed-off-by: Tahsin Erdogan <tahsin@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of overloading the discard support with the REQ_SECURE flag.
Use the opportunity to rename the queue flag as well, and remove the
dead checks for this flag in the RAID 1 and RAID 10 drivers that don't
claim support for secure erase.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the block layer merging code to use separate variables
for the operation and flags, and to check req_op for the REQ_OP.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the simple bi_rw use cases in the block,
drivers, mm and fs code to set/get the bio operation using
bio_set_op_attrs/bio_op
These should be simple one or two liner cases, so I just did them
in one patch. The next patches handle the more complicated
cases in a module per patch.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We currently set REQ_WRITE/WRITE for all non READ IOs
like discard, flush, writesame, etc. In the next patches where we
no longer set up the op as a bitmap, we will not be able to
detect a operation direction like writesame by testing if REQ_WRITE is
set.
This patch converts the drivers and cgroup to use the
op_is_write helper. This should just cover the simple
cases. I did dm, md and bcache in their own patches
because they were more involved.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch applies the two introduced helpers to
figure out the 1st and last bvec.
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
After commit e36f62042880(block: split bios to maxpossible length),
bio can be splitted in the middle of a vector entry, then it
is easy to split out one bio which size isn't aligned with block
size, especially when the block size is bigger than 512.
This patch fixes the issue by making the max io size aligned
to logical block size.
Fixes: e36f62042880(block: split bios to maxpossible length)
Reported-by: Stefan Haberland <sth@linux.vnet.ibm.com>
Cc: Keith Busch <keith.busch@intel.com>
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull core block updates from Jens Axboe:
"We don't have a lot of core changes this time around, it's mostly in
drivers, which will come in a subsequent pull.
The cores changes include:
- blk-mq
- Prep patch from Christoph, changing blk_mq_alloc_request() to
take flags instead of just using gfp_t for sleep/nosleep.
- Doc patch from me, clarifying the difference between legacy
and blk-mq for timer usage.
- Fixes from Raghavendra for memory-less numa nodes, and a reuse
of CPU masks.
- Cleanup from Geliang Tang, using offset_in_page() instead of open
coding it.
- From Ilya, rename request_queue slab to it reflects what it holds,
and a fix for proper use of bdgrab/put.
- A real fix for the split across stripe boundaries from Keith. We
yanked a broken version of this from 4.4-rc final, this one works.
- From Mike Krinkin, emit a trace message when we split.
- From Wei Tang, two small cleanups, not explicitly clearing memory
that is already cleared"
* 'for-4.5/core' of git://git.kernel.dk/linux-block:
block: use bd{grab,put}() instead of open-coding
block: split bios to max possible length
block: add call to split trace point
blk-mq: Avoid memoryless numa node encoded in hctx numa_node
blk-mq: Reuse hardware context cpumask for tags
blk-mq: add a flags parameter to blk_mq_alloc_request
Revert "blk-flush: Queue through IO scheduler when flush not required"
block: clarify blk_add_timer() use case for blk-mq
bio: use offset_in_page macro
block: do not initialise statics to 0 or NULL
block: do not initialise globals to 0 or NULL
block: rename request_queue slab cache
This splits bio in the middle of a vector to form the largest possible
bio at the h/w's desired alignment, and guarantees the bio being split
will have some data.
The criteria for splitting is changed from the max sectors to the h/w's
optimal sector alignment if it is provided. For h/w that advertise their
block storage's underlying chunk size, it's a big performance win to not
submit commands that cross them. If sector alignment is not provided,
this patch uses the max sectors as before.
This addresses the performance issue commit d380561113 attempted to
fix, but was reverted due to splitting logic error.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Cc: Jens Axboe <axboe@fb.com>
Cc: Ming Lei <tom.leiming@gmail.com>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: <stable@vger.kernel.org> # 4.4.x-
Signed-off-by: Jens Axboe <axboe@fb.com>
This reverts commit d380561113.
If we end up splitting on the first segment, we don't adjust
the sector count. That results in hitting a BUG() with attempting
to split 0 sectors.
As this is just a performance issue and not a regression since
4.3 release, let's just rever this change. That gives us more
time to test a real fix for 4.5, which would be marked for
stable anyway.
For h/w that advertise their block storage's underlying chunk size, it's
a big performance win to not submit commands that cross them. This patch
uses that criteria if it is provided. If it is not provided, this patch
uses the max sectors as before.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
There is a split tracepoint that is supposed to be called when
bio is splitted, and it was called in bio_split function until
commit 4b1faf9316 ("block: Kill bio_pair_split()").
But now, no one reports splits, so this patch adds call to
trace_block_split back in blk_queue_split right after split.
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
When bio has only one physical segment, we should set bio's
bi_seg_front_size as the real(final) size of the single segment.
Fixes: 02e707424c2ea(blk-merge: fix blk_bio_segment_split)
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We had seen lots of reports of this kind issue, so add one
warnning in blk-merge, then it can be triggered easily and
avoid to depend on warning/bug from drivers.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit bdced438acd83a(block: setup bi_phys_segments after
splitting) introduces function of computing bio->bi_phys_segments
during bio splitting.
Unfortunately both bio->bi_seg_front_size and bio->bi_seg_back_size
arn't computed, so too many physical segments may be obtained
for one request since both the two are used to check if one segment
across two bios can be possible.
This patch fixes the issue by computing the two variables in
blk_bio_segment_split().
Fixes: bdced438acd83a(block: setup bi_phys_segments after splitting)
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Inside blk_bio_segment_split(), previous bvec pointer(bvprvp)
always points to the iterator local variable, which is obviously
wrong, so fix it by pointing to the local variable of 'bvprv'.
Fixes: 5014c311baa2b(block: fix bogus compiler warnings in blk-merge.c)
Cc: stable@kernel.org #4.3
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Reported-by: Mark Salter <msalter@redhat.com>
Tested-by: Laurent Dufour <ldufour@linux.vnet.ibm.com>
Tested-by: Mark Salter <msalter@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The splitted bio has been already too fat to merge, so mark it
as NOMERGE.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The number of bio->bi_phys_segments is always obtained
during bio splitting, so it is natural to setup it
just after bio splitting, then we can avoid to compute
nr_segment again during merge.
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
biovecs has become immutable since v3.13, so it isn't necessary
to allocate biovecs for the new cloned bios, then we can save
one extra biovecs allocation/copy, and the allocation is often
not fixed-length and a bit more expensive.
For example, if the 'max_sectors_kb' of null blk's queue is set
as 16(32 sectors) via sysfs just for making more splits, this patch
can increase throught about ~70% in the sequential read test over
null_blk(direct io, bs: 1M).
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Ming Lin <ming.l@ssi.samsung.com>
Cc: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
This fixes a performance regression introduced by commit 54efd50bfd,
and allows us to take full advantage of the fact that we have immutable
bio_vecs. Hand applied, as it rejected violently with commit
5014c311ba.
Signed-off-by: Jens Axboe <axboe@fb.com>
If a driver sets the block queue virtual boundary mask, it means that
it cannot handle gaps so we must not allow those in the integrity
payload as well.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Fixed up by me to have duplicate integrity merge functions, depending
on whether block integrity is enabled or not. Fixes a compilations
issue with CONFIG_BLK_DEV_INTEGRITY unset.
Signed-off-by: Jens Axboe <axboe@fb.com>
We are checking for gaps to previous bio_vec, which can
only detect back merges gaps. Moreover, at the point where
we check for a gap, we don't know if we will attempt a back
or a front merge. Thus, check for gap to prev in a back merge
attempt and check for a gap to next in a front merge attempt.
Signed-off-by: Jens Axboe <axboe@fb.com>
[sagig: Minor rename change]
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
The compiler can't figure out that bvprv is initialized whenever 'prev'
is set to 1 as well. Use a pointer to bvprv instead, setting it to NULL
initially, and get rid of the 'prev' tracking. This dumbs it down
enough that gcc is happy.
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull SG updates from Jens Axboe:
"This contains a set of scatter-gather related changes/fixes for 4.3:
- Add support for limited chaining of sg tables even for
architectures that do not set ARCH_HAS_SG_CHAIN. From Christoph.
- Add sg chain support to target_rd. From Christoph.
- Fixup open coded sg->page_link in crypto/omap-sham. From
Christoph.
- Fixup open coded crypto ->page_link manipulation. From Dan.
- Also from Dan, automated fixup of manual sg_unmark_end()
manipulations.
- Also from Dan, automated fixup of open coded sg_phys()
implementations.
- From Robert Jarzmik, addition of an sg table splitting helper that
drivers can use"
* 'for-4.3/sg' of git://git.kernel.dk/linux-block:
lib: scatterlist: add sg splitting function
scatterlist: use sg_phys()
crypto/omap-sham: remove an open coded access to ->page_link
scatterlist: remove open coded sg_unmark_end instances
crypto: replace scatterwalk_sg_chain with sg_chain
target/rd: always chain S/G list
scatterlist: allow limited chaining without ARCH_HAS_SG_CHAIN
The SG_GAPS queue flag caused checks for bio vector alignment against
PAGE_SIZE, but the device may have different constraints. This patch
adds a queue limits so a driver with such constraints can set to allow
requests that would have been unnecessarily split. The new gaps check
takes the request_queue as a parameter to simplify the logic around
invoking this function.
This new limit makes the queue flag redundant, so removing it and
all usage. Device-mappers will inherit the correct settings through
blk_stack_limits().
Signed-off-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
[hch: split from a larger patch by Dan]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
As generic_make_request() is now able to handle arbitrarily sized bios,
it's no longer necessary for each individual block driver to define its
own ->merge_bvec_fn() callback. Remove every invocation completely.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@kernel.org>
Cc: ceph-devel@vger.kernel.org
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: also remove ->merge_bvec_fn() in dm-thin as well as
dm-era-target, and resolve merge conflicts]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The way the block layer is currently written, it goes to great lengths
to avoid having to split bios; upper layer code (such as bio_add_page())
checks what the underlying device can handle and tries to always create
bios that don't need to be split.
But this approach becomes unwieldy and eventually breaks down with
stacked devices and devices with dynamic limits, and it adds a lot of
complexity. If the block layer could split bios as needed, we could
eliminate a lot of complexity elsewhere - particularly in stacked
drivers. Code that creates bios can then create whatever size bios are
convenient, and more importantly stacked drivers don't have to deal with
both their own bio size limitations and the limitations of the
(potentially multiple) devices underneath them. In the future this will
let us delete merge_bvec_fn and a bunch of other code.
We do this by adding calls to blk_queue_split() to the various
make_request functions that need it - a few can already handle arbitrary
size bios. Note that we add the call _after_ any call to
blk_queue_bounce(); this means that blk_queue_split() and
blk_recalc_rq_segments() don't need to be concerned with bouncing
affecting segment merging.
Some make_request_fn() callbacks were simple enough to audit and verify
they don't need blk_queue_split() calls. The skipped ones are:
* nfhd_make_request (arch/m68k/emu/nfblock.c)
* axon_ram_make_request (arch/powerpc/sysdev/axonram.c)
* simdisk_make_request (arch/xtensa/platforms/iss/simdisk.c)
* brd_make_request (ramdisk - drivers/block/brd.c)
* mtip_submit_request (drivers/block/mtip32xx/mtip32xx.c)
* loop_make_request
* null_queue_bio
* bcache's make_request fns
Some others are almost certainly safe to remove now, but will be left
for future patches.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Jim Paris <jim@jtan.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md/md.c' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: skip more mq-based drivers, resolve merge conflicts, etc.]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Some places use helpers now, others don't. We only have the 'is set'
helper, add helpers for setting and clearing flags too.
It was a bit of a mess of atomic vs non-atomic access. With
BIO_UPTODATE gone, we don't have any risk of concurrent access to the
flags. So relax the restriction and don't make any of them atomic. The
flags that do have serialization issues (reffed and chained), we
already handle those separately.
Signed-off-by: Jens Axboe <axboe@fb.com>
We can safely merge anything that wont generate an SG list entry,
so if the bio is data-less (discard), don't look at potential
SG gaps.
Signed-off-by: Jens Axboe <axboe@fb.com>
Use the right array index to reference the last
element of rq->biotail->bi_io_vec[]
Signed-off-by: Wenbo Wang <wenbo.wang@memblaze.com>
Reviewed-by: Chong Yuan <chong.yuan@memblaze.com>
Fixes: 66cb45aa41 ("block: add support for limiting gaps in SG lists")
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
If the queue has SG_GAPS set, we must not merge across an sg gap.
This is caught for the bio case, but currently not for the
more rare case of merging two requests directly.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Cut the dm bits, those will go through the dm tree, and fixed
the test_bit() test.
Signed-off-by: Jens Axboe <axboe@fb.com>
For cloned bio, bio->bi_vcnt can't be used at all, and we
have resort to bio_segments() to figure out how many
segment there are in the bio.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The problem is introduced by commit 764f612c6c3c231b(blk-merge:
don't compute bi_phys_segments from bi_vcnt for cloned bio),
and merge is needed if number of current segment isn't less than
max segments.
Strictly speaking, bio->bi_vcnt shouldn't be used here since
it may not be accurate in cases of both cloned bio or bio cloned
from, but bio_segments() is a bit expensive, and bi_vcnt is still
the biggest number, so the approach should work.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
It isn't correct to figure out req->bi_phys_segments from bio->bi_vcnt
if the bio is cloned.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Tested-by: Jeff Mahoney <jeffm@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We'd occasionally merge requests with conflicting integrity flags.
Introduce a merge helper which checks that the requests have compatible
integrity payloads.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
QUEUE_FLAG_NO_SG_MERGE is set at default for blk-mq devices,
so bio->bi_phys_segment computed may be bigger than
queue_max_segments(q) for blk-mq devices, then drivers will
fail to handle the case, for example, BUG_ON() in
virtio_queue_rq() can be triggerd for virtio-blk:
https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1359146
This patch fixes the issue by ignoring the QUEUE_FLAG_NO_SG_MERGE
flag if the computed bio->bi_phys_segment is bigger than
queue_max_segments(q), and the regression is caused by commit
05f1dd53152173(block: add queue flag for disabling SG merging).
Reported-by: Kick In <pierre-andre.morey@canonical.com>
Tested-by: Chris J Arges <chris.j.arges@canonical.com>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Another restriction inherited for NVMe - those devices don't support
SG lists that have "gaps" in them. Gaps refers to cases where the
previous SG entry doesn't end on a page boundary. For NVMe, all SG
entries must start at offset 0 (except the first) and end on a page
boundary (except the last).
Signed-off-by: Jens Axboe <axboe@fb.com>
If devices are not SG starved, we waste a lot of time potentially
collapsing SG segments. Enough that 1.5% of the CPU time goes
to this, at only 400K IOPS. Add a queue flag, QUEUE_FLAG_NO_SG_MERGE,
which just returns the number of vectors in a bio instead of looping
over all segments and checking for collapsible ones.
Add a BLK_MQ_F_SG_MERGE flag so that drivers can opt-in on the sg
merging, if they so desire.
Signed-off-by: Jens Axboe <axboe@fb.com>
Immutable biovecs changed the way biovecs are interpreted - drivers no
longer use bi_vcnt, they have to go by bi_iter.bi_size (to allow for
using part of an existing segment without modifying it).
This breaks with discards and write_same bios, since for those bi_size
has nothing to do with segments in the biovec. So for now, we need a
fairly gross hack - we fortunately know that there will never be more
than one segment for the entire request, so we can special case
discard/write_same.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Tested-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Christoph Hellwig