Sync code to the same with tk4 pub/lts/0017-kabi, except deleted rue
and wujing. Partners can submit pull requests to this branch, and we
can pick the commits to tk4 pub/lts/0017-kabi easly.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Sync kernel codes to the same with 590eaf1fec ("Init Repo base on
linux 5.4.32 long term, and add base tlinux kernel interfaces."), which
is from tk4, and it is the base of tk4.
Signed-off-by: Jianping Liu <frankjpliu@tencent.com>
Perform CQ initialization in the driver when the capability is supported
by the FW. When passing the CQ to HW indicate that the CQ buffer has
been pre-initialized.
Doing so decreases CQ creation time. Testing on P8 showed a single 2048
entry CQ creation time was reduced from ~395us to ~170us, which is
2.3x faster.
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This parameter enables capturing region snapshot of the crspace
during critical errors. The default value of this parameter is
disabled, it can be enabled using devlink param commands.
It is possible to configure during runtime and also driver init.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Crdump allows the driver to create a snapshot of the FW PCI
crspace and health buffer during a critical FW issue.
In case of a FW command timeout, FW getting stuck or a non zero
value on the catastrophic buffer, a snapshot will be taken.
The snapshot is exposed using devlink, cr-space, fw-health
address regions are registered on init and snapshots are attached
once a new snapshot is collected by the driver.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Health buffer address is a 32 bit PCI address offset provided by
the FW. This offset is used for reading FW health debug data
located on the shared CR space. Cr space is accessible in both
driver and FW and allows for different queries and configurations.
Health buffer size is always 64B of readable data followed by a
lock which is used to block volatile CR space access.
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If supported, write a driver version string to FW as part of the
INIT_HCA command.
Example of driver version: "Linux,mlx4_core,4.0-0"
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MLX4_USER_DEV_CAP_LARGE_CQE (via mlx4_ib_alloc_ucontext_resp.dev_caps)
and MLX4_IB_QUERY_DEV_RESP_MASK_CORE_CLOCK_OFFSET (via
mlx4_uverbs_ex_query_device_resp.comp_mask) are copied directly to
userspace and form part of the uAPI.
Move them to the uapi header where they belong.
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
- Add iWARP support to qedr driver
- Lots of misc fixes across subsystem
- Multiple update series to hns roce driver
- Multiple update series to hfi1 driver
- Updates to vnic driver
- Add kref to wait struct in cxgb4 driver
- Updates to i40iw driver
- Mellanox shared pull request
- timer_setup changes
- massive cleanup series from Bart Van Assche
- Two series of SRP/SRPT changes from Bart Van Assche
- Core updates from Mellanox
- i40iw updates
- IPoIB updates
- mlx5 updates
- mlx4 updates
- hns updates
- bnxt_re fixes
- PCI write padding support
- Sparse/Smatch/warning cleanups/fixes
- CQ moderation support
- SRQ support in vmw_pvrdma
-----BEGIN PGP SIGNATURE-----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=A1oL
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a fairly plain pull request. Lots of driver updates across the
stack, a huge number of static analysis cleanups including a close to
50 patch series from Bart Van Assche, and a number of new features
inside the stack such as general CQ moderation support.
Nothing really stands out, but there might be a few conflicts as you
take things in. In particular, the cleanups touched some of the same
lines as the new timer_setup changes.
Everything in this pull request has been through 0day and at least two
days of linux-next (since Stephen doesn't necessarily flag new
errors/warnings until day2). A few more items (about 30 patches) from
Intel and Mellanox showed up on the list on Tuesday. I've excluded
those from this pull request, and I'm sure some of them qualify as
fixes suitable to send any time, but I still have to review them
fully. If they contain mostly fixes and little or no new development,
then I will probably send them through by the end of the week just to
get them out of the way.
There was a break in my acceptance of patches which coincides with the
computer problems I had, and then when I got things mostly back under
control I had a backlog of patches to process, which I did mostly last
Friday and Monday. So there is a larger number of patches processed in
that timeframe than I was striving for.
Summary:
- Add iWARP support to qedr driver
- Lots of misc fixes across subsystem
- Multiple update series to hns roce driver
- Multiple update series to hfi1 driver
- Updates to vnic driver
- Add kref to wait struct in cxgb4 driver
- Updates to i40iw driver
- Mellanox shared pull request
- timer_setup changes
- massive cleanup series from Bart Van Assche
- Two series of SRP/SRPT changes from Bart Van Assche
- Core updates from Mellanox
- i40iw updates
- IPoIB updates
- mlx5 updates
- mlx4 updates
- hns updates
- bnxt_re fixes
- PCI write padding support
- Sparse/Smatch/warning cleanups/fixes
- CQ moderation support
- SRQ support in vmw_pvrdma"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (296 commits)
RDMA/core: Rename kernel modify_cq to better describe its usage
IB/mlx5: Add CQ moderation capability to query_device
IB/mlx4: Add CQ moderation capability to query_device
IB/uverbs: Add CQ moderation capability to query_device
IB/mlx5: Exposing modify CQ callback to uverbs layer
IB/mlx4: Exposing modify CQ callback to uverbs layer
IB/uverbs: Allow CQ moderation with modify CQ
iw_cxgb4: atomically flush the qp
iw_cxgb4: only call the cq comp_handler when the cq is armed
iw_cxgb4: Fix possible circular dependency locking warning
RDMA/bnxt_re: report vlan_id and sl in qp1 recv completion
IB/core: Only maintain real QPs in the security lists
IB/ocrdma_hw: remove unnecessary code in ocrdma_mbx_dealloc_lkey
RDMA/core: Make function rdma_copy_addr return void
RDMA/vmw_pvrdma: Add shared receive queue support
RDMA/core: avoid uninitialized variable warning in create_udata
RDMA/bnxt_re: synchronize poll_cq and req_notify_cq verbs
RDMA/bnxt_re: Flush CQ notification Work Queue before destroying QP
RDMA/bnxt_re: Set QP state in case of response completion errors
RDMA/bnxt_re: Add memory barriers when processing CQ/EQ entries
...
Exposed mlx4_ib_modify_cq to be called from ib device
verb list.
Signed-off-by: Yonatan Cohen <yonatanc@mellanox.com>
Reviewed-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable mlx4_srq.refcount is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable mlx4_qp.refcount is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
atomic_t variables are currently used to implement reference
counters with the following properties:
- counter is initialized to 1 using atomic_set()
- a resource is freed upon counter reaching zero
- once counter reaches zero, its further
increments aren't allowed
- counter schema uses basic atomic operations
(set, inc, inc_not_zero, dec_and_test, etc.)
Such atomic variables should be converted to a newly provided
refcount_t type and API that prevents accidental counter overflows
and underflows. This is important since overflows and underflows
can lead to use-after-free situation and be exploitable.
The variable mlx4_cq.refcount is used as pure reference counter.
Convert it to refcount_t and fix up the operations.
Suggested-by: Kees Cook <keescook@chromium.org>
Reviewed-by: David Windsor <dwindsor@gmail.com>
Reviewed-by: Hans Liljestrand <ishkamiel@gmail.com>
Signed-off-by: Elena Reshetova <elena.reshetova@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
1) Support ipv6 checksum offload in sunvnet driver, from Shannon
Nelson.
2) Move to RB-tree instead of custom AVL code in inetpeer, from Eric
Dumazet.
3) Allow generic XDP to work on virtual devices, from John Fastabend.
4) Add bpf device maps and XDP_REDIRECT, which can be used to build
arbitrary switching frameworks using XDP. From John Fastabend.
5) Remove UFO offloads from the tree, gave us little other than bugs.
6) Remove the IPSEC flow cache, from Florian Westphal.
7) Support ipv6 route offload in mlxsw driver.
8) Support VF representors in bnxt_en, from Sathya Perla.
9) Add support for forward error correction modes to ethtool, from
Vidya Sagar Ravipati.
10) Add time filter for packet scheduler action dumping, from Jamal Hadi
Salim.
11) Extend the zerocopy sendmsg() used by virtio and tap to regular
sockets via MSG_ZEROCOPY. From Willem de Bruijn.
12) Significantly rework value tracking in the BPF verifier, from Edward
Cree.
13) Add new jump instructions to eBPF, from Daniel Borkmann.
14) Rework rtnetlink plumbing so that operations can be run without
taking the RTNL semaphore. From Florian Westphal.
15) Support XDP in tap driver, from Jason Wang.
16) Add 32-bit eBPF JIT for ARM, from Shubham Bansal.
17) Add Huawei hinic ethernet driver.
18) Allow to report MD5 keys in TCP inet_diag dumps, from Ivan
Delalande.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1780 commits)
i40e: point wb_desc at the nvm_wb_desc during i40e_read_nvm_aq
i40e: avoid NVM acquire deadlock during NVM update
drivers: net: xgene: Remove return statement from void function
drivers: net: xgene: Configure tx/rx delay for ACPI
drivers: net: xgene: Read tx/rx delay for ACPI
rocker: fix kcalloc parameter order
rds: Fix non-atomic operation on shared flag variable
net: sched: don't use GFP_KERNEL under spin lock
vhost_net: correctly check tx avail during rx busy polling
net: mdio-mux: add mdio_mux parameter to mdio_mux_init()
rxrpc: Make service connection lookup always check for retry
net: stmmac: Delete dead code for MDIO registration
gianfar: Fix Tx flow control deactivation
cxgb4: Ignore MPS_TX_INT_CAUSE[Bubble] for T6
cxgb4: Fix pause frame count in t4_get_port_stats
cxgb4: fix memory leak
tun: rename generic_xdp to skb_xdp
tun: reserve extra headroom only when XDP is set
net: dsa: bcm_sf2: Configure IMP port TC2QOS mapping
net: dsa: bcm_sf2: Advertise number of egress queues
...
- Lots of hfi1 driver updates (mixed with a few qib and core updates as
well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so we
can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@
-----BEGIN PGP SIGNATURE-----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=2ntC
-----END PGP SIGNATURE-----
Merge tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull rdma updates from Doug Ledford:
"This is a big pull request.
Of note is that I'm sending you the new ioctl API for the rdma
subsystem. We put it up on linux-api@, but didn't get much response.
The API is complex, but it solves two different problems in one go:
1) The bi-directional nature of the RDMA file write calls, which
created the security hole we had to handle (and for which the fix
is now causing problems for systems in production, we were a bit
over zealous in the fix and the ability to open a device, then
fork, then create new queue pairs on the device and use them is
broken).
2) The bloat caused by different vendors implementing extensions to
the base verbs API. Each vendor's hardware is slightly different,
and the hardware might be suitable for one extension but not
another.
By the time we add generic extensions for all the different ways
that the different hardware can offload things, the API becomes
bloated. Things like our completion structs have started to exceed
a cache line in size because of all the elements needed to support
this. That in turn shows up heavily in the performance graphs with
a noticable drop in performance on 100Gigabit links as our
completion structs go from occupying one cache line to 1+.
This API makes things like the completion structs modular in a
very similar way to netlink so that your structs can only include
the items needed for the offloads/features you are actually using
on a given queue pair. In that way we support everything, but only
use what we need, and our structs stay smaller.
The ioctl API is better explained by the posting on linux-api@ than I
can explain it here, so I'll just leave it at that.
The rest of the pull request is typical stuff.
Updates for 4.14 kernel merge window
- Lots of hfi1 driver updates (mixed with a few qib and core updates
as well)
- rxe updates
- various mlx updates
- Set default roce type to RoCEv2
- Several larger fixes for bnxt_re that were too big for -rc
- Several larger fixes for qedr that, likewise, were too big for -rc
- Misc core changes
- Make the hns_roce driver compilable on arches other than aarch64 so
we can more easily debug build issues related to it
- Add rdma-netlink infrastructure updates
- Add automatic IRQ affinity infrastructure
- Add 32bit lid support
- Lots of misc fixes across the subsystem from random people
- Autoloading of RDMA netlink modules
- PCI pool cleanups from Romain Perier
- mlx5 driver feature additions and fixes
- Hardware tag matchine feature
- Fix sleeping in atomic when resolving roce ah
- Add experimental ioctl interface as posted to linux-api@"
* tag 'for-linus-ioctl' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (328 commits)
IB/core: Expose ioctl interface through experimental Kconfig
IB/core: Assign root to all drivers
IB/core: Add completion queue (cq) object actions
IB/core: Add legacy driver's user-data
IB/core: Export ioctl enum types to user-space
IB/core: Explicitly destroy an object while keeping uobject
IB/core: Add macros for declaring methods and attributes
IB/core: Add uverbs merge trees functionality
IB/core: Add DEVICE object and root tree structure
IB/core: Declare an object instead of declaring only type attributes
IB/core: Add new ioctl interface
RDMA/vmw_pvrdma: Fix a signedness
RDMA/vmw_pvrdma: Report network header type in WC
IB/core: Add might_sleep() annotation to ib_init_ah_from_wc()
IB/cm: Fix sleeping in atomic when RoCE is used
IB/core: Add support to finalize objects in one transaction
IB/core: Add a generic way to execute an operation on a uobject
Documentation: Hardware tag matching
IB/mlx5: Support IB_SRQT_TM
net/mlx5: Add XRQ support
...
Adding support for updating the FW on new port mac, when port mac change
is requested by the user. This info is required by the FW as OEM
management tools require this info directly from the NIC FW.
Check device capability bit to verify the FW supports user mac.
If the FW does support it, use set_port command to notify the FW on the
new mac.
The feature is relevant only to PF port mac.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid temporary large structs on the stack,
allocate them dynamically.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tal Alon <talal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently when WoL is supported but disabled, ethtool reports:
"Supports Wake-on: d".
Fix the indication of Wol support, so that the indication
remains "g" all the time if the NIC supports WoL.
Tested:
As accepted, when NIC supports WoL- ethtool reports:
Supports Wake-on: g
Wake-on: d
when NIC doesn't support WoL- ethtool reports:
Supports Wake-on: d
Wake-on: d
Fixes: 14c07b1358 ("mlx4: Wake on LAN support")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding visibility of resource usage of QPs, CQs and counters used by
virtual functions. This feature will be used to give the PF administrator
more data while debugging VF status. Usage info was added to ALLOC_RES
command, to notify the PF if the resource which is being reserved or
allocated for the VF will be used by kernel driver or by user verbs.
Updated reservation and allocation functions of QP, CQ and counter with
additional usage parameter.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Our previous patch (cited below) introduced a regression
for RAW Eth QPs.
Fix it by checking if the QP number provided by user-space
exists, hence allowing steering rules to be added for valid
QPs only.
Fixes: 89c557687a ("net/mlx4_en: Avoid adding steering rules with invalid ring")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Talat Batheesh <talatb@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On some environments, such as certain SR-IOV VF configurations, RoCE
isn't supported for mlx4 Ethernet ports. Currently the driver will
not open IB device on that port.
This is problematic since we do want user-space RAW Ethernet QPs functionality
to remain in place. For that end, enhance the relevant driver flows such that we
do create a device instance in that case.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Some Hypervisors detach VFs from VMs by instantly causing an FLR event
to be generated for a VF.
In the mlx4 case, this will cause that VF's comm channel to be disabled
before the VM has an opportunity to invoke the VF device's "shutdown"
method.
For such Hypervisors, there is a race condition between the VF's
shutdown method and its internal-error detection/reset thread.
The internal-error detection/reset thread (which runs every 5 seconds) also
detects a disabled comm channel. If the internal-error detection/reset
flow wins the race, we still get delays (while that flow tries repeatedly
to detect comm-channel recovery).
The cited commit fixed the command timeout problem when the
internal-error detection/reset flow loses the race.
This commit avoids the unneeded delays when the internal-error
detection/reset flow wins.
Fixes: d585df1c5c ("net/mlx4_core: Avoid command timeouts during VF driver device shutdown")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reported-by: Simon Xiao <sixiao@microsoft.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bitwise & was obviously intended here.
Fixes: 745d8ae462 ("net/mlx4: Spoofcheck and zero MAC can't coexist")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spoofcheck can't be enabled if VF MAC is zero.
Vice versa, can't zero MAC if spoofcheck is on.
Fixes: 8f7ba3ca12 ('net/mlx4: Add set VF mac address support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When starting the port, driver will inform Firmware about the actual MTU
which does not include implicit headers, such as FCS or VLAN tags.
Signed-off-by: Shaker Daibes <shakerd@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This feature will allow the user to disable auto negotiation
on the port for mlx4 devices while setting the speed is limited
to 1GbE speeds.
Other speeds will not be accepted in autoneg off mode.
This functionality is permitted providing that the firmware
is compatible with this feature.
The above is determined by querying a new dedicated capability
bit in the device.
Signed-off-by: Ariel Levkovich <lariel@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Demoting simple flow steering rule priority (for DPDK) was achieved by
wrapping FW commands MLX4_QP_FLOW_STEERING_ATTACH/DETACH for the PF
as well, and forcing the priority to MLX4_DOMAIN_NIC in the wrapper
function for the PF and all VFs.
In function mlx4_ib_create_flow(), this change caused the main rule
creation for the PF to be wrapped, while it left the associated
tunnel steering rule creation unwrapped for the PF.
This mismatch caused rule deletion failures in mlx4_ib_destroy_flow()
for the PF when the detach wrapper function did not find the associated
tunnel-steering rule (since creation of that rule for the PF did not
go through the wrapper function).
Fix this by setting MLX4_QP_FLOW_STEERING_ATTACH/DETACH to be "native"
(so that the PF invocation does not go through the wrapper), and perform
the required priority demotion for the PF in the mlx4_ib_create_flow()
code path.
Fixes: 48564135cb ("net/mlx4_core: Demote simple multicast and broadcast flow steering rules")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Currently interrupt test that is part of ethtool selftest runs the
check over all interrupt vectors of the device.
In mlx4_en package part of interrupt vectors are uninitialized since
mlx4_ib doesn't exist. This causes NOP FW command to time out.
Change logic to test current port interrupt vectors only.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates to mlx5
- Updates to mlx4 (two conflicts, both minor and easily resolved)
- Updates to iw_cxgb4 (one conflict, not so obvious to resolve, proper
resolution is to keep the code in cxgb4_main.c as it is in Linus'
tree as attach_uld was refactored and moved into cxgb4_uld.c)
- Improvements to uAPI (moved vendor specific API elements to uAPI area)
- Add hns-roce driver and hns and hns-roce ACPI reset support
- Conversion of all rdma code away from deprecated
create_singlethread_workqueue
- Security improvement: remove unsafe ib_get_dma_mr (breaks lustre in
staging)
-----BEGIN PGP SIGNATURE-----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=LC+S
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull main rdma updates from Doug Ledford:
"This is the main pull request for the rdma stack this release. The
code has been through 0day and I had it tagged for linux-next testing
for a couple days.
Summary:
- updates to mlx5
- updates to mlx4 (two conflicts, both minor and easily resolved)
- updates to iw_cxgb4 (one conflict, not so obvious to resolve,
proper resolution is to keep the code in cxgb4_main.c as it is in
Linus' tree as attach_uld was refactored and moved into
cxgb4_uld.c)
- improvements to uAPI (moved vendor specific API elements to uAPI
area)
- add hns-roce driver and hns and hns-roce ACPI reset support
- conversion of all rdma code away from deprecated
create_singlethread_workqueue
- security improvement: remove unsafe ib_get_dma_mr (breaks lustre in
staging)"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (75 commits)
staging/lustre: Disable InfiniBand support
iw_cxgb4: add fast-path for small REG_MR operations
cxgb4: advertise support for FR_NSMR_TPTE_WR
IB/core: correctly handle rdma_rw_init_mrs() failure
IB/srp: Fix infinite loop when FMR sg[0].offset != 0
IB/srp: Remove an unused argument
IB/core: Improve ib_map_mr_sg() documentation
IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets
IB/mthca: Move user vendor structures
IB/nes: Move user vendor structures
IB/ocrdma: Move user vendor structures
IB/mlx4: Move user vendor structures
IB/cxgb4: Move user vendor structures
IB/cxgb3: Move user vendor structures
IB/mlx5: Move and decouple user vendor structures
IB/{core,hw}: Add constant for node_desc
ipoib: Make ipoib_warn ratelimited
IB/mlx4/alias_GUID: Remove deprecated create_singlethread_workqueue
IB/ipoib_verbs: Remove deprecated create_singlethread_workqueue
IB/ipoib: Remove deprecated create_singlethread_workqueue
...
In MLX qp packets, the LRH (built by the driver) has both a VL field
and an SL field. When building a QP1 packet, the VL field should
reflect the SLtoVL mapping and not arbitrarily contain zero (as is
done now). This bug causes credit problems in IB switches at
high rates of QP1 packets.
The fix is to cache the SL to VL mapping in the driver, and look up
the VL mapped to the SL provided in the send request when sending
QP1 packets.
For FW versions which support generating a port_management_config_change
event with subtype sl-to-vl-table-change, the driver uses that event
to update its sl-to-vl mapping cache. Otherwise, the driver snoops
incoming SMP mads to update the cache.
There remains the case where the FW is running in secure-host mode
(so no QP0 packets are delivered to the driver), and the FW does not
generate the sl2vl mapping change event. To support this case, the
driver updates (via querying the FW) its sl2vl mapping cache when
running in secure-host mode when it receives either a Port Up event
or a client-reregister event (where the port is still up, but there
may have been an opensm failover).
OpenSM modifies the sl2vl mapping before Port Up and Client-reregister
events occur, so if there is a mapping change the driver's cache will
be properly updated.
Fixes: 225c7b1fee ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Move the vf to VST 802.1ad mode (mlx4 VST QinQ mode) by setting vf vlan
protocol to 802.1ad.
VST 802.1ad mode in mlx4, is used for STAG strip/insertion by PF, while
the CTAG is set by the VF.
Read current vlan protocol as part of the vf configuration state.
Upon setting vf vlan protocol to 802.1ad, we use a mechanism of handshake
to verify that both the vf and the pf driver version support it.
The handshake uses the command QUERY_FUNC_CAP:
- The vf sets a pre-defined support bit in input modifier.
- A pf that supports the feature sends the request to the vf through a
pre-defined field in the output mailbox.
- In case vf does not support the feature, the pf will fail the control
command (in this case, IP link tool command to set the vf vlan
protocol to 802.1ad).
No change in VST 802.1Q mode.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Check device capability to support VF vlan protocol 802.1ad mode.
Add vport attribute vlan protocol.
Init vport vlan protocol by default to 802.1Q.
Add update QP support for VF vlan protocol 802.1ad.
Add func capability vlan_offload_disable to disable all
vlan HW acceleration on VF while the VF is set to VF vlan protocol
802.1ad mode.
No change in VF vlan protocol 802.1Q (VST) mode.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=oZOO
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma
Pull base rdma updates from Doug Ledford:
"Round one of 4.8 code: while this is mostly normal, there is a new
driver in here (the driver was hosted outside the kernel for several
years and is actually a fairly mature and well coded driver). It
amounts to 13,000 of the 16,000 lines of added code in here.
Summary:
- Updates/fixes for iw_cxgb4 driver
- Updates/fixes for mlx5 driver
- Add flow steering and RSS API
- Add hardware stats to mlx4 and mlx5 drivers
- Add firmware version API for RDMA driver use
- Add the rxe driver (this is a software RoCE driver that makes any
Ethernet device a RoCE device)
- Fixes for i40iw driver
- Support for send only multicast joins in the cma layer
- Other minor fixes"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dledford/rdma: (72 commits)
Soft RoCE driver
IB/core: Support for CMA multicast join flags
IB/sa: Add cached attribute containing SM information to SA port
IB/uverbs: Fix race between uverbs_close and remove_one
IB/mthca: Clean up error unwind flow in mthca_reset()
IB/mthca: NULL arg to pci_dev_put is OK
IB/hfi1: NULL arg to sc_return_credits is OK
IB/mlx4: Add diagnostic hardware counters
net/mlx4: Query performance and diagnostics counters
net/mlx4: Add diagnostic counters capability bit
Use smaller 512 byte messages for portmapper messages
IB/ipoib: Report SG feature regardless of HW UD CSUM capability
IB/mlx4: Don't use GFP_ATOMIC for CQ resize struct
IB/hfi1: Disable by default
IB/rdmavt: Disable by default
IB/mlx5: Fix port counter ID association to QP offset
IB/mlx5: Fix iteration overrun in GSI qps
i40iw: Add NULL check for puda buffer
i40iw: Change dup_ack_thresh to u8
i40iw: Remove unnecessary check for moving CQ head
...
Expose IB diagnostic hardware counters.
The counters count IB events and are applicable for IB and RoCE.
The counters can be divided into two groups, per device and per port.
Device counters are always exposed.
Port counters are exposed only if the firmware supports per port counters.
rq_num_dup and sq_num_to are only exposed if we have firmware support
for them, if we do, we expose them per device and per port.
rq_num_udsdprd and num_cqovf are device only counters.
rq - denotes responder.
sq - denotes requester.
|-----------------------|---------------------------------------|
| Name | Description |
|-----------------------|---------------------------------------|
|rq_num_lle | Number of local length errors |
|-----------------------|---------------------------------------|
|sq_num_lle | number of local length errors |
|-----------------------|---------------------------------------|
|rq_num_lqpoe | Number of local QP operation errors |
|-----------------------|---------------------------------------|
|sq_num_lqpoe | Number of local QP operation errors |
|-----------------------|---------------------------------------|
|rq_num_lpe | Number of local protection errors |
|-----------------------|---------------------------------------|
|sq_num_lpe | Number of local protection errors |
|-----------------------|---------------------------------------|
|rq_num_wrfe | Number of CQEs with error |
|-----------------------|---------------------------------------|
|sq_num_wrfe | Number of CQEs with error |
|-----------------------|---------------------------------------|
|sq_num_mwbe | Number of Memory Window bind errors |
|-----------------------|---------------------------------------|
|sq_num_bre | Number of bad response errors |
|-----------------------|---------------------------------------|
|sq_num_rire | Number of Remote Invalid request |
| | errors |
|-----------------------|---------------------------------------|
|rq_num_rire | Number of Remote Invalid request |
| | errors |
|-----------------------|---------------------------------------|
|sq_num_rae | Number of remote access errors |
|-----------------------|---------------------------------------|
|rq_num_rae | Number of remote access errors |
|-----------------------|---------------------------------------|
|sq_num_roe | Number of remote operation errors |
|-----------------------|---------------------------------------|
|sq_num_tree | Number of transport retries exceeded |
| | errors |
|-----------------------|---------------------------------------|
|sq_num_rree | Number of RNR NAK retries exceeded |
| | errors |
|-----------------------|---------------------------------------|
|rq_num_rnr | Number of RNR NAKs sent |
|-----------------------|---------------------------------------|
|sq_num_rnr | Number of RNR NAKs received |
|-----------------------|---------------------------------------|
|rq_num_oos | Number of Out of Sequence requests |
| | received |
|-----------------------|---------------------------------------|
|sq_num_oos | Number of Out of Sequence NAKs |
| | received |
|-----------------------|---------------------------------------|
|rq_num_udsdprd | Number of UD packets silently |
| | discarded on the Receive Queue due to |
| | lack of receive descriptor |
|-----------------------|---------------------------------------|
|rq_num_dup | Number of duplicate requests received |
|-----------------------|---------------------------------------|
|sq_num_to | Number of time out received |
|-----------------------|---------------------------------------|
|num_cqovf | Number of CQ overflows |
|-----------------------|---------------------------------------|
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a function to query diagnostics counters from the firmware.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
Add a bit that indicates if the firmware supports per port
diagnostic counters.
Signed-off-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
In preparation for writing the tx descriptor from multiple functions,
create a helper for both normal and blueflame access.
Signed-off-by: Brenden Blanco <bblanco@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Several cases of overlapping changes, except the packet scheduler
conflicts which deal with the addition of the free list parameter
to qdisc_enqueue().
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for reading and updating priority flow
control (PFC) attributes in the driver via netlink.
Signed-off-by: Rana Shahout <ranas@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows a clean shutdown, even if some netdev clients do not
release their reference from this netdev. It is enough to release
the HW resources only as the kernel is shutting down.
Fixes: 2ba5fbd62b ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma_alloc_coherent() function returns a virtual address which can
be used for coherent access to the underlying memory. On some
architectures, like arm64, undefined behavior results if this memory is
also accessed via virtual mappings that are not coherent. Because of
their undefined nature, operations like virt_to_page() return garbage
when passed virtual addresses obtained from dma_alloc_coherent(). Any
subsequent mappings via vmap() of the garbage page values are unusable
and result in bad things like bus errors (synchronous aborts in ARM64
speak).
The mlx4 driver contains code that does the equivalent of:
vmap(virt_to_page(dma_alloc_coherent)), this results in an OOPs when the
device is opened.
Prevent Ethernet driver to run this problematic code by forcing it to
allocate contiguous memory. As for the Infiniband driver, at first we
are trying to allocate contiguous memory, but in case of failure roll
back to work with fragmented memory.
Signed-off-by: Haggai Abramovsky <hagaya@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Reported-by: David Daney <david.daney@cavium.com>
Tested-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain the PCI status and provide wrappers for enabling and disabling
the PCI device. Performing the actions more than once without doing
its opposite results in warning logs.
This occurred when EEH hotplugged the device causing a warning for
disabling an already disabled device.
Fixes: 2ba5fbd62b ('net/mlx4_core: Handle AER flow properly')
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking updates from David Miller:
"Highlights:
1) Support more Realtek wireless chips, from Jes Sorenson.
2) New BPF types for per-cpu hash and arrap maps, from Alexei
Starovoitov.
3) Make several TCP sysctls per-namespace, from Nikolay Borisov.
4) Allow the use of SO_REUSEPORT in order to do per-thread processing
of incoming TCP/UDP connections. The muxing can be done using a
BPF program which hashes the incoming packet. From Craig Gallek.
5) Add a multiplexer for TCP streams, to provide a messaged based
interface. BPF programs can be used to determine the message
boundaries. From Tom Herbert.
6) Add 802.1AE MACSEC support, from Sabrina Dubroca.
7) Avoid factorial complexity when taking down an inetdev interface
with lots of configured addresses. We were doing things like
traversing the entire address less for each address removed, and
flushing the entire netfilter conntrack table for every address as
well.
8) Add and use SKB bulk free infrastructure, from Jesper Brouer.
9) Allow offloading u32 classifiers to hardware, and implement for
ixgbe, from John Fastabend.
10) Allow configuring IRQ coalescing parameters on a per-queue basis,
from Kan Liang.
11) Extend ethtool so that larger link mode masks can be supported.
From David Decotigny.
12) Introduce devlink, which can be used to configure port link types
(ethernet vs Infiniband, etc.), port splitting, and switch device
level attributes as a whole. From Jiri Pirko.
13) Hardware offload support for flower classifiers, from Amir Vadai.
14) Add "Local Checksum Offload". Basically, for a tunneled packet
the checksum of the outer header is 'constant' (because with the
checksum field filled into the inner protocol header, the payload
of the outer frame checksums to 'zero'), and we can take advantage
of that in various ways. From Edward Cree"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1548 commits)
bonding: fix bond_get_stats()
net: bcmgenet: fix dma api length mismatch
net/mlx4_core: Fix backward compatibility on VFs
phy: mdio-thunder: Fix some Kconfig typos
lan78xx: add ndo_get_stats64
lan78xx: handle statistics counter rollover
RDS: TCP: Remove unused constant
RDS: TCP: Add sysctl tunables for sndbuf/rcvbuf on rds-tcp socket
net: smc911x: convert pxa dma to dmaengine
team: remove duplicate set of flag IFF_MULTICAST
bonding: remove duplicate set of flag IFF_MULTICAST
net: fix a comment typo
ethernet: micrel: fix some error codes
ip_tunnels, bpf: define IP_TUNNEL_OPTS_MAX and use it
bpf, dst: add and use dst_tclassid helper
bpf: make skb->tc_classid also readable
net: mvneta: bm: clarify dependencies
cls_bpf: reset class and reuse major in da
ldmvsw: Checkpatch sunvnet.c and sunvnet_common.c
ldmvsw: Add ldmvsw.c driver code
...
Implement newly introduced devlink interface. Add devlink port instances
for every port and set the port types accordingly.
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
v2->v3:
-add dev param to devlink_register (api change)
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for receiving multicast/unicast traffic with
the don't trap rule.
Sniffing these packets requires a flow steering rule of type NORMAL
at priority 0 with flag IB_FLOW_ATTR_FLAGS_DONT_TRAP set.
Choosing between multicast or unicast is done via ethernet L2 dest_mac
mask and value:
- If mask is all zeros - unicast and multicast are set.
- If mask non zero - only mask with multicast bit 1 and rest 0 is
supported, the mac value will choose if it is
multicast or unicast rule.
If the mask multicast bit is on and some other bits are on too, it means
a request for specific multicast or unicast, this is not supported,
either receive all multicast or all unicast.
Only when limitations are met registered QP will receive requested type
but other QPs can receive same traffic if registered for it.
Otherwise, if limitations are not met, an error will be returned.
Limitations:
- Rule must be with priority 0.
- A0 mode is not supported.
- Sniffer QP cannot appear in any other flow steering rule.
Signed-off-by: Marina Varshaver <marinav@mellanox.com>
Reviewed-by: Matan Barak <matanb@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
problem description:
The current code sets UAR page size equal to system page size.
The ConnectX-3 and ConnectX-3 Pro HWs require minimum 128 UAR pages.
The mlx4 kernel drivers are not loaded if there is less than 128 UAR pages.
solution:
Always set UAR page to 4KB. This allows more UAR pages if the OS
has PAGE_SIZE larger than 4KB. For example, PowerPC kernel use 64KB
system page size, with 4MB uar region, there are 4MB/2/64KB = 32
uars (half for uar, half for blueflame). This does not meet minimum 128
UAR pages requirement. With 4KB UAR page, there are 4MB/2/4KB = 512 uars
which meet the minimum requirement.
Note that only codes in mlx4_core that deal with firmware know that uar
page size is 4KB. Codes that deal with usr page in cq and qp context
(mlx4_ib, mlx4_en and part of mlx4_core) still have the same assumption
that uar page size equals to system page size.
Note that with this implementation, on 64KB system page size kernel, there
are 16 uars per system page but only one uars is used. The other 15
uars are ignored because of the above assumption.
Regarding SR-IOV, mlx4_core in hypervisor will set the uar page size
to 4KB and mlx4_core code in virtual OS will obtain the uar page size from
firmware.
Regarding backward compatibility in SR-IOV, if hypervisor has this new code,
the virtual OS must be updated. If hypervisor has old code, and the virtual
OS has this new code, the new code will be backward compatible with the
old code. If the uar size is big enough, this new code in VF continues to
work with 64 KB uar page size (on PowerPc kernel). If the uar size does not
meet 128 uars requirement, this new code not loaded in VF and print the same
error message as the old code in Hypervisor.
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jianping Liu