/sys/bus/pci/drivers/megaraid_sas/poll_mode_io defaults to being
world-writable, which seems bad (letting any user affect kernel driver
behavior).
This turns off group and user write permissions, so that on typical
production systems only root can write to it.
Signed-off-by: Bryn M. Reeves <bmr@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix discovery failures:
- Move all accesses to the fc_flag field inside the host lock.
- Restore link state after going through linkdown processing for FCF DEAD event.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix SCSI protocol related errors:
- Avoid I/O failures during EEH and HBA/CNA reset by correcting when
we block the targets on the adapter.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix hardware/SLI relates issues:
- Fix CNA uses more than one EQ when in INTx interrupt mode.
- Fix driver tries to process failed read FCF record mailbox request.
- Fix allocating single receive buffer breaks FCoE receive queue.
- Support new read FCF record mailbox error case.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix NPIV operation errors:
- Fix vport not logging out of fabric when being deleted
- Fix vport fails to discover targets after devloss timeout.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix FC protocol errors:
- Fix multi-frame unsolicited sequences not queued properly
- Fix frames for unsolicited sequences not being associated with sequence.
- Fix unsolicited frame buffer sizes are not set properly
- Fix Sequence count for unsolicited frame headers not byte swapped.
- Fix Multi-frame sequence response frames go to wrong DID.
Signed-off-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
During a manual scan, a user can send command to a nonexistent
lun, precisely at the point of max_lun. Normally it's possible
(but not required) that the firmware has the knowledge that it
is an invalid lun. In the particular case when max_lun is 256,
however, the nonexistent lun 256 will be confused with lun 0,
because the lun member in a request message is only u8, and 256
will become 0. So we need to fix the problem, at least, at the
driver level.
Signed-off-by: Ed Lin <ed.lin@promise.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
For a particular driver error condition, driver was doing double
scsi_dma_unmaps. Driver was calling scsi_dma_unmap in
pmcraid_error_handler and return 0. This pmcraid_error_handler is called
by pmcraid_io_done which will do scsi_dma_unmap again when it has
return 0 from pmcraid_error_handler.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Added fundamental reset and pci save state.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Hold the hardware lock while do the response completion in work queue threads as
it involves sharing a common request queue among multiple threads.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
When the hba port gets logged out of the fabric, or other
such transitional state when the physical link is still present,
the driver doesn't receive a loop up asyn event (where the link
data rate currently gets set). Hence send a explicit mailbox command
to get the link rate in such conditions.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix a target login issue, when parent interface is vlan and we are
using cxgb3i sepecific private ip address in '/etc/iscsi/ifaces/'
iface file.
Signed-off-by: Rakesh Ranjan <rakesh@chelsio.com>
Acked-by: Karen Xie <kxie@chelsio.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix the "ignoring return value of '...', declared with attribute
warn_unused_result" compiler warning in several users of the new kfifo
API.
It removes the __must_check attribute from kfifo_in() and
kfifo_in_locked() which must not necessary performed.
Fix the allocation bug in the nozomi driver file, by moving out the
kfifo_alloc from the interrupt handler into the probe function.
Fix the kfifo_out() and kfifo_out_locked() users to handle a unexpected
end of fifo.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
rename kfifo_put... into kfifo_in... to prevent miss use of old non in
kernel-tree drivers
ditto for kfifo_get... -> kfifo_out...
Improve the prototypes of kfifo_in and kfifo_out to make the kerneldoc
annotations more readable.
Add mini "howto porting to the new API" in kfifo.h
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move the pointer to the spinlock out of struct kfifo. Most users in
tree do not actually use a spinlock, so the few exceptions now have to
call kfifo_{get,put}_locked, which takes an extra argument to a
spinlock.
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a new generic kernel FIFO implementation.
The current kernel fifo API is not very widely used, because it has to
many constrains. Only 17 files in the current 2.6.31-rc5 used it.
FIFO's are like list's a very basic thing and a kfifo API which handles
the most use case would save a lot of development time and memory
resources.
I think this are the reasons why kfifo is not in use:
- The API is to simple, important functions are missing
- A fifo can be only allocated dynamically
- There is a requirement of a spinlock whether you need it or not
- There is no support for data records inside a fifo
So I decided to extend the kfifo in a more generic way without blowing up
the API to much. The new API has the following benefits:
- Generic usage: For kernel internal use and/or device driver.
- Provide an API for the most use case.
- Slim API: The whole API provides 25 functions.
- Linux style habit.
- DECLARE_KFIFO, DEFINE_KFIFO and INIT_KFIFO Macros
- Direct copy_to_user from the fifo and copy_from_user into the fifo.
- The kfifo itself is an in place member of the using data structure, this save an
indirection access and does not waste the kernel allocator.
- Lockless access: if only one reader and one writer is active on the fifo,
which is the common use case, no additional locking is necessary.
- Remove spinlock - give the user the freedom of choice what kind of locking to use if
one is required.
- Ability to handle records. Three type of records are supported:
- Variable length records between 0-255 bytes, with a record size
field of 1 bytes.
- Variable length records between 0-65535 bytes, with a record size
field of 2 bytes.
- Fixed size records, which no record size field.
- Preserve memory resource.
- Performance!
- Easy to use!
This patch:
Since most users want to have the kfifo as part of another object,
reorganize the code to allow including struct kfifo in another data
structure. This requires changing the kfifo_alloc and kfifo_init
prototypes so that we pass an existing kfifo pointer into them. This
patch changes the implementation and all existing users.
[akpm@linux-foundation.org: fix warning]
Signed-off-by: Stefani Seibold <stefani@seibold.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'cpumask-cleanups' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
cpumask: rename tsk_cpumask to tsk_cpus_allowed
cpumask: don't recommend set_cpus_allowed hack in Documentation/cpu-hotplug.txt
cpumask: avoid dereferencing struct cpumask
cpumask: convert drivers/idle/i7300_idle.c to cpumask_var_t
cpumask: use modern cpumask style in drivers/scsi/fcoe/fcoe.c
cpumask: avoid deprecated function in mm/slab.c
cpumask: use cpu_online in kernel/perf_event.c
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-misc-2.6: (40 commits)
[SCSI] 3w-9xxx fix bug in sgl loading
[SCSI] fcoe, libfc: adds enable/disable for fcoe interface
[SCSI] libfc: reduce hold time on SCSI host lock
[SCSI] libfc: remote port gets stuck in restart state without really restarting
[SCSI] pm8001: misc code cleanup
[SCSI] pm8001: enable read HBA SAS address from VPD
[SCSI] pm8001: do not reset local sata as it will not be found if reset
[SCSI] pm8001: bit set pm8001_ha->flags
[SCSI] pm8001:fix potential NULL pointer dereference
[SCSI] pm8001: set SSC down-spreading only to get less errors on some 6G device.
[SCSI] pm8001: fix endian issues with SAS address
[SCSI] pm8001: enhance error handle for IO patch
[SCSI] pm8001: Fix for sata io circular lock dependency.
[SCSI] hpsa: add driver for HP Smart Array controllers.
[SCSI] cxgb3i: always use negative errno in case of error
[SCSI] bnx2i: minor code cleanup and update driver version
[SCSI] bnx2i: Task management ABORT TASK fixes
[SCSI] bnx2i: update CQ arming algorith for 5771x chipsets
[SCSI] bnx2i: Adjust sq_size module parametr to power of 2 only if a non-zero value is specified
[SCSI] bnx2i: Add 5771E device support to bnx2i driver
...
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Cc: Robert Love <robert.w.love@intel.com>
Cc: Chris Leech <christopher.leech@intel.com>
Cc: linux-scsi@vger.kernel.org
Recently, We marked strstrip() as must_check. because it was frequently
misused and it should be checked. However, we found one exception.
scsi/ipr.c intentionally ignore return value of strstrip. Because it
wishes to keep the whitespace at the beginning.
Thus we need to keep with and without checked whitespace trim function.
This patch adds a new strim() and changes ipr.c to use it.
[akpm@linux-foundation.org: coding-style fixes]
Suggested-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
To avoid a collision with the newly-added kernel-wide skip_spaces().
Signed-off-by: André Goddard Rosa <andre.goddard@gmail.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This small patch fixes a bug in the 3w-9xxx driver where it would load
an invalid sgl address in the ioctl path even if request length was zero.
Signed-off-by: Adam Radford <aradford@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This is to allow fcoemon util to enable or disable a fcoe interface
according to DCB link state change.
Adds sysfs module param enable and disable for this and also
updates existing other module param description to be consistent
and more accurate since older description had double "fcoe" word
with less meaningful netdev reference to user space.
Adds code to ignore redundant fc_lport_enter_reset handling for a
already disabled fcoe interface by checking LPORT_ST_DISABLED
or LPORT_ST_LOGO states, this also prevents lport state transition
on link flap on a disabled interface.
Above changes required lport state transition to get out of
disabled or logo state on call to fc_fabric_login.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Introduce a new lock to protect the list of fc_fcp_pkt structs in libfc
instead of using the host lock. This reduces the contention of this heavily
used lock, and I see up to a 25% performance gain in CPU bound small I/O
tests when scaling out across multiple quad-core CPUs.
The big win is in removing the host lock from the completion path
completely, as it does not need to be held around the call to scsi_done.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
We ran into a scenario where a remote port goes into RESTART state, but
never gets added to scsi transport. The running vmcore showed the following:
a) Port was in RESTART state
b) rdata->event was STOP
c) no work gets scheduled for the remote work to fc_rport_work
After this point, shut/no-shut of the remote port did not cause the port
to get re-discovered. The port would move betwen DELETE and RESTART states,
but the event would always be STOP, no work would get scheduled to
fc_rport_work and the port would not get added to scsi_transport.
The problem is that rdata->event is not set to NONE after a port is
restarted. After this point, no more work gets scheduled for the remote port
since new work is scheduled only if rdata->event is non-NONE. So, the event
and state keep changing, but fc_rport_work does not get scheduled to actually
handle the event.
Here's a transition of states that explains the above observation:
) Port is first in READY State, event is NONE
2) RSCN on shut, port goes to DELETED, event is stop
3) Before fc_rport_work runs, RSCN on no-shut, port goes to RESTART, event is
still STOP
4) fc_rport_work gets scheduled, removes the port from transport, sees state
as RESTART, begins the PLOGI state machine, event remains as STOP (event NOT
changed to NONE, this is the bug)
5) Plogi state machine completes, port state goes to READY, event goes to
READY, but no work is scheduled since event was STOP (non-NONE) before.
Fc_rport_work is not scheduled, port remains in READY state, but is not added
to transport.
Things are broken at this point. Libfc rport is ready, but no transport rport
created.
6) now a shut causes port state to change to DELETE, event to change to STOP,
no work gets scheduled
7) no-shut causes port state to change to RESTART, event remains at STOP,
no work gets scheduled
(6) and (7) now get repeated everytime we do shut/no-shut. No way to get out
of this state. Fcc reset does not help too.
Only way to get out is to load/unload module.
Fix is to set rdata->event to NONE while processing the STOP/LOGO/FAILED
events, inside the discovery and rport locks.
Signed-off-by: Abhijeet Joglekar <abjoglek@cisco.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Add more data to printk's, add some spaces around arithmetic ops and
improve comments.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Enhance error handle for IO patch, when the port is down, fast return phy
down for task.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This patch fix for sata IO circular lock dependency. When we call task_done
for SATA IO, we have got pm8001_ha->lock ,and in sas_ata_task_done, it will
get (dev->sata_dev.ap->lock. then cause circular lock dependency .So we
should drop pm8001_ha->lock when we call task_done for SATA task.
Signed-off-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: Lindar Liu <lindar_liu@usish.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This driver supports a subset of HP Smart Array Controllers.
It is a SCSI alternative to the cciss driver.
[akpm@linux-foundation.org: avoid helpful cleanup patches]
[achiang@hp.com: make device attrs static]
[akpm@linux-foundation.org: msleep() does set_current_state() itself]
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Mike Miller <mikem@beardog.cce.hp.com>
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed duplicate function call and not-so-useful comment line
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Due to typo error driver was failing TMF Abort Task request when
ctask->sc != NULL. Fixed code to fail TMF ABORT Task request only when
ctask->sc == NULL. Clear age component (19 most significant bits) of
reference ITT carried in iSCSI TMF PDU. Age component is internal to
initiator side and only lower bits of ITT as defined by ISCSI_ITT_MASK
is is sent on wire. Retrieve LUN directly from the ref_sc and update
SQ wqe as per chip HSI (Host Software Interface) specification
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Only affects 5771x (10G chipsets) devices
This is an optimized CQ arming algoritm which takes into account the
number of outstanding tasks
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
This issue was discovered during 10G iscsi testing
Default value of 'sq_size' module parameter is '0' which means driver
should use predefined SQ queue size when setting up iscsi connection.
roundup_pow_of_two(0) results in '1' and forces driver to setup
connections with send queue size of '1' and results in lower
performance as well
Signed-off-by: Anil Veerabhadrappa <anilgv@broadcom.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
After commits c82f63e411 (PCI: check saved
state before restore) and 4b77b0a2ba (PCI:
Clear saved_state after the state has been restored) PCI drivers are
prevented from restoring the device standard configuration registers
twice in a row. These changes introduced a regression on ipr EEH
recovery.
The ipr device driver saves the PCI state only during the device probe
and restores it on ipr_reset_restore_cfg_space() during IOA resets. This
behavior is causing the EEH recovery to fail after the second error
detected, since the registers are not being restored.
One possible solution would be saving the registers after restoring
them. The problem with this approach is that while recovering from an
EEH error if pci_save_state() results in an EEH error, the adapter/slot
will be reset, and end up back in ipr_reset_restore_cfg_space(), but it
won't have a valid saved state to restore, so pci_restore_state() will
fail.
The following patch introduces a workaround for this problem, hacking
around the PCI API by setting pdev->state_saved = true before we do the
restore. It fixes the EEH regression and prevents that we hit another
EEH error during EEH recovery.
[jejb: fix is a hack ... Jesse and Rafael will fix properly]
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: stable@kernel.org
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
If the LLD wants its own WWNN/WWPN to be used, it should implement the
netdev_ops.ndo_fcoe_get_wwn(). If that is the case, we query the LLD and use
the queried WWNN/WWPN from the LLD.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Fix to accommodate a hardware bug in multiqueue mode that does not
work properly when acknowledgement of MSIX Interrupts is disabled.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Removed the module parameters ql2xqfulltracking and ql2xqfullrampup
since the queue depth ramp up/down functionality is moved to scsi-ml.
Signed-off-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Bryn M. Reeves