This driver supports the 3 DCDC and 7 LDO regulators available on
Ricoh RN5T618 PMIC.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In some cases we need to know when a regulator is about to be changed.
Add a way for clients to be notified. Note that for set_voltage() we
don't necessarily know what voltage we'll end up with, so we tell the
client what the range will be so they can prepare.
Signed-off-by: Heiko Stübner <heiko@sntech.de>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie+linaro@kernel.org>
The memory allocated in rk808_regulator_probe() needs to be freed when the
module is unloaded. Thus pass &pdev->dev rather than &client->dev to
devm_kzalloc.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The max77802 driver reads the default operating mode (opmode)
set for regulators when enabled from the hardware registers.
But if a regulator is disabled and the system warm restarted,
the hardware reports OFF as the opmode so the regulator is
not enabled. Default to operating mode NORMAL if OFF is read
from the hardware register.
Reported-by: Yuvaraj Cd <yuvaraj.lkml@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Yuvaraj Kumar CD <yuvaraj.cd@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a patch for supporting device tree of DA9211/DA9213.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
remove the redundant code, since pdata has been removed from stuct rk808
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The "dev" has been deleted from "struct rk808" in rk808 mfd driver
so rk808->dev should be replaced by &client->dev here.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The RK808 regulator driver was putting its config on the stack but not
initting it. That means that you got a semi-random config. Fix this.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The valid_modes_mask and *dev are not used in this driver, remove them.
Current code uses devm_regulator_register, so we don't need *regulator in
hi6421_regulator_info. Use a local variable instead.
Also removes a few unnecessary inclusion of header files.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The regulator module consists of 4 DCDCs, 8 LDOs and 2 switches.
The output voltages are configurable and are meant to supply power
to the main processor and other components
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Both num_regulators and *rdev[MAX77802_REG_MAX] are not used, remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
style fix for warnings. 'else' with a single 'return' is usually not
required.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 272e2315fa ("regulator: core: add const qualifier to ops in
struct regulator_desc") introduced const qualifier to ops in regulator_desc.
This patch adds 'const' to regulator_ops vars in newly added core APIs
for v3.17-rc1:
- regulator_get_hardware_vsel_register()
- regulator_list_hardware_vsel()
This patch also fix a build error in mc13892-regulator.c due to const
regulator_desc.ops. Modification of regulator_desc.ops' member fields is not
allowed.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The MAX77802 PMIC has 10 high-efficiency Buck and 32 Low-dropout
(LDO) regulators. This patch adds support for all these regulators
found on the MAX77802 PMIC and is based on a driver added by Simon
Glass to the Chrome OS kernel 3.8 tree.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Naveen Krishna Chatradhi <ch.naveen@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add driver support for HiSilicon Hi6421 voltage regulators.
Two rules for regulator enabling are defined in hi6421 spec:
1) Between disable and enable of each regulator (LDOs or BUCKs), there must
be a protection gap. Use @off_on_delay of regulator core to implement this.
2) No two regulators can be enabled at the same time. Use mutex in
hi6421_regulator_pdata to ensure this. A protection gap of 100us is added
into each LDO/BUCK's .enable_time.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some regulator require a minimum delay between its disable and next enable.
This is to avoid damages when out-of-range frequent disable/enable of a
single regulator can bring to the regulator chip.
Add @off_on_delay to struct regulator_desc. Device drivers' can use this field
to set this guard time.
Add @last_off_jiffy to struct regulator_dev. When @off_on_delay is set by
driver, regulator core can store its last off (disable) time into this field.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
A common delay function can be helpful when implementing new features. Factor
it out to maximize code reusability.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
struct regulator_ops *ops is a member in struct regulator_desc, which gets
its value from individual regulator driver upon regulator_register() and
is used by regulator core APIs. It's not allowed for regulator core to
modify any of these callbacks in *ops. Add 'const' qualifier to enforce that.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The regulator core supports this to allow the configuration to be inspected
at runtime even if no software management is enabled.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch makes the regulator description macro take minimum and
steps voltage as parameter. In this way many repeated macros can be
removed. Now these macros are repeated only if the the LDO/BUCK ctrl
registers have non-linear positions. The good thing is these ctrl registers
are mostly linear so they are not passed as parameters.
This patch reduces the code size and also allow easy addition of more
s2mpxxx PMIC drivers which differs a lot in minimum/step voltages.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch makes the regulator description macro take minimum and
steps voltage as parameter. In this way many repeated macros can be
removed. Now these macros are repeated only if the the LDO/BUCK ctrl
registers have non-linear positions. The good thing is these ctrl registers
are mostly linear so they are not passed as parameters.
This patch reduces the code size and also allow easy addition of more
s2mpxxx PMIC drivers which differs a lot in minimum/step voltages.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is a cleanup patch and moves min/step voltages in a common samsung
header file so that they can be used by other s2mpxxx PMIC drivers. Only
few required macros are added currently and others can be added if needed.
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Since commit b42261078a ("regmap: i2c: fallback to SMBus if the adapter
does not support standard I2C"), regmap-i2c will check the
I2C_FUNC_SMBUS_[BYTE|WORD]_DATA functionality based on the regmap_config
setting if the adapter does not support standard I2C.
So remove the I2C_FUNC_SMBUS_BYTE_DATA functionality check in the driver code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
- Checkpatch fixes throughout the subsystem
- Use Regmap to handle IRQs in max77686, extcon-max77693 and mc13xxx-core
- Use DMA in rtsx_pcr
- Restrict building on unsupported architectures on timberdale, cs5535
- SPI hardening in cros_ec_spi
- More robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- Reorder PM runtime and regulator handing during shutdown in arizona
- Enable wakeup in cros_ec_spi
- Unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- Add regulator handing into suspend() in sec-core
- Remove pointless wrapper functions in extcon-max77693 and i2c-cros-ec-tunnel
- Use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- Device Tree documentation updates throughout
- Provide power management support in max77686
- Few OF clean-ups in max77686
- Use manged resources in tps6105x
== New drivers/supported devices ==
- Add support for s2mpu02 to sec-core
- Add support for Allwinner A32 to sun6i-prcm
- Add support for Maxim 77802 in max77686
- Add support for DA9063 AD in da9063
- Add new driver for Intel PMICs (generic) and specifically Crystal Cove
== (Re-)moved drivers ==
- Move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=2cNI
-----END PGP SIGNATURE-----
Merge tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD update from Lee Jones:
"Changes to existing drivers:
- checkpatch fixes throughout the subsystem
- use Regmap to handle IRQs in max77686, extcon-max77693 and
mc13xxx-core
- use DMA in rtsx_pcr
- restrict building on unsupported architectures on timberdale,
cs5535
- SPI hardening in cros_ec_spi
- more robust error handing in asic3, cros_ec, ab8500-debugfs,
max77686 and pcf50633-core
- reorder PM runtime and regulator handing during shutdown in arizona
- enable wakeup in cros_ec_spi
- unused variable/code clean-up in pm8921-core, cros_ec, htc-i2cpld,
tps65912-spi, wm5110-tables and ab8500-debugfs
- add regulator handing into suspend() in sec-core
- remove pointless wrapper functions in extcon-max77693 and
i2c-cros-ec-tunnel
- use cross-architecture friendly data sizes in stmpe-i2c, arizona,
max77686 and tps65910
- devicetree documentation updates throughout
- provide power management support in max77686
- few OF clean-ups in max77686
- use manged resources in tps6105x
New drivers/supported devices:
- add support for s2mpu02 to sec-core
- add support for Allwinner A32 to sun6i-prcm
- add support for Maxim 77802 in max77686
- add support for DA9063 AD in da9063
- new driver for Intel PMICs (generic) and specifically Crystal Cove
(Re-)moved drivers ==
- move out keyboard functionality cros_ec ==> input/keyboard/cros_ec_keyb"
* tag 'mfd-for-linus-3.17' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (101 commits)
MAINTAINERS: Update MFD repo location
mfd: omap-usb-host: Fix improper mask use.
mfd: arizona: Only free the CTRLIF_ERR IRQ if we requested it
mfd: arizona: Add missing handling for ISRC3 under/overclocked
mfd: wm5110: Add new interrupt register definitions
mfd: arizona: Rename thermal shutdown interrupt
mfd: wm5110: Add in the output done interrupts
mfd: wm5110: Remove non-existant interrupts
mfd: tps65912-spi: Remove unused variable
mfd: htc-i2cpld: Remove unused code
mfd: da9063: Add support for AD silicon variant
mfd: arizona: Map MICVDD from extcon device to the Arizona core
mfd: arizona: Add MICVDD to mapped regulators for wm8997
mfd: max77686: Ensure device type IDs are architecture agnostic
mfd: max77686: Add Maxim 77802 PMIC support
mfd: tps6105x: Use managed resources when allocating memory
mfd: wm8997-tables: Suppress 'line over 80 chars' warnings
mfd: kempld-core: Correct a variety of checkpatch warnings
mfd: ipaq-micro: Fix coding style errors/warnings reported by checkpatch
mfd: si476x-cmd: Remedy checkpatch style complains
...
act8846_matches and act8865_matches are defined only when OF is
enabled. Move references to them to the act8865_pdata_from_dt()
function to avoid a build error when OF is disabled.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add device id and definition of registers and regulators to support
the act8846 PMU.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch prepares support for other devices in the act88xx family of
PMUs manufactured by Active-Semi.
http://www.active-semi.com/products/power-management-units/act88xx/
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
act8865_pdata_from_dt() populates the array pdata->regulators with all
the regulators and then assigns the field init_data only for the ones
actually found in the DT.
The patch changes the value assigned to pdata->num_regulators to match
the size of the array.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Simply use ret variable instead.
Also remove unneeded initialize for ret variable.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The driver loops through all available regulators (ACT8865_REG_NUM)
and accesses pdata->regulators[i].platform_data without checking the
actual value of num_regulators in platform data, potentially causing a
invalid memory access.
Fix this and look up the regulator init_data by id in platform data.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by Wenyou.Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
According to the tps65090 data manual [0], the DCDC1 and DCDC2
step-down converters and the LDO's have a fixed output voltage.
Add this information to the driver since these fixed regulators
can be used as parent input supply for switches that don't have
an output voltage defined. So the regulator core needs to fetch
the FET parent output voltage if the child voltage is queried.
[0]: http://www.ti.com/lit/gpn/tps65090
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Load switches are modeled as regulators but they just provide
the voltage of their parent input supply. So, the drivers for
these switches usually neither provide a .list_voltage handler
not set a .n_voltages count. But there is code in the kernel
that assumes that all regulators should be able to provide this
information (e.g: cpufreq and mmc subsystems).
If the voltage count and list are not available for a regulator
and it has a parent input supply, then use the parent values.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Load switches are modeled as regulators but they just provide
the voltage of their parent input supply. So the drivers for
these switches usually don't provide a .get_voltage function
handler but there is code in the kernel that assumes that all
regulators should be able to provide its current voltage rail.
So, if the output voltage for a regulator is not available and
it has a parent supply, then pass the voltage of its parent.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Regulator drivers should not be specifying constraints since the valid
configurations depend on how the device is used in a given system, there
is no way to know if a configuration is safe for a given board.
Signed-off-by: Mark Brown <broonie@linaro.org>
This driver also supports S2MPU02 now, thus update module description and
Kconfig accordingly.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add helper functions that allow regulator consumers to obtain low-level
details about the regulator hardware, like the voltage selector register
address and such. These details can be useful when configuring hardware
or firmware that want to do low-level access to regulators, with no
involvement from the kernel.
The use-case for Tegra is a voltage-controlled oscillator clocksource
which has control logic to change the supply voltage via I2C to achieve
a desired output clock rate.
Signed-off-by: Tuomas Tynkkynen <ttynkkynen@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current code uses devm_regulator_register(), so the resource management code
will ensure that the resource is freed.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This is the driver for the Dialog DA9211 Multi-phase 12A DC-DC Buck
Converter regulator. It communicates via an I2C bus to the device.
Signed-off-by: James Ban <james.ban.opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch add S2MPU02 regulator device to existing S2MPS11 device driver
because of little difference between S2MPS1x and S2MPU02. The S2MPU02
regulator device includes LDO[1-28] and BUCK[1-7].
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
[Add missing linear_min_sel of S2MPU02 LDO regulators by Jonghwa Lee]
Signed-off-by: Jonghwa Lee <jonghwa3.lee@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
This patch moves data allocated using regulator_register to
devm_regulator_register and does away with the calls to
regulator_unregister. Also some labels are removed and a new labelerr is
introduced which is less specific to context.
Signed-off-by: Himangi Saraogi <himangi774@gmail.com>
Acked-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
By just using GCC's array initialization extension, we
can easily drop order dependency between tps65218_regulattors
enumeration and tps65218_pmic_regs array.
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
volt table is always NULL for all regulators,
might as well drop the argument.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The second range of this particular regulator,
starts at 1.60V, not as 1.55V as it was originally
implied by code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
act8865_pdata_from_dt() populates the array pdata->regulators with all
the regulators and then assigns the field init_data only for the ones
actually found in the DT.
The patch changes the value assigned to pdata->num_regulators to match
the size of the array.
Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Tested-by: Wenyou Yang <wenyou.yang@atmel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
WM5110/8280 devices do not support bypass mode for LDO1 so remove
the bypass callbacks registered with regulator core.
Signed-off-by: Nikesh Oswal <nikesh@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
We use regmap regulator ops to enable/disable and check if regulator
is enabled for various SMPS. However, these depend on valid
enable_reg, enable_mask and enable_value in regulator descriptor.
So, similar to fix we did in commit 318dbb02b5
("regulator: palmas: Fix SMPS enable/disable/is_enabled"), populate the
same for TPS65917 SMPS registration. LDO definitions are already in
place.
Fixes: d6f83370ed ("regulator: palmas: Add tps65917 PMIC support")
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Palmas regulator needs to full up the regulator_desc based on PMIC and
type of regulator. However, we dont need to do desc[id] every time. we
can simplify by using a pointer to desc[id] and filling up the
parameters.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With commit d6f83370ed (regulator: palmas:
Add tps65917 PMIC support) palmas_regs_info naming is confusing as it is
a driver data parameter and a local variable. To prevent mistaken
updates, rename the local variable to palmas_generic_regs_info.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Palmas register information is part of the ddata pointer which is used
through out the code by indexing off the driver data array. Instead,
just do the indexing once and use the pointer to further reference
structure fields.
This simplifies code and prevents errors by accessing wrong variables.
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
reg_info is a generic term which might cause conflict at a later point
in time. To prevent such a thing from occuring in future, rename to
palmas_reg_info.
Signed-off-by: Nishanth Menon <nm@ti.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
convert to static variables to squelch the following sparse warnings:
drivers/regulator/palmas-regulator.c:325:36: warning: symbol 'palma_sleep_req_info' was not declared. Should it be static?
drivers/regulator/palmas-regulator.c:1414:32: warning: symbol 'palmas_ddata' was not declared. Should it be static?
drivers/regulator/palmas-regulator.c:1427:32: warning: symbol 'tps65917_ddata' was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Convert the regulator GPIO handling to use a gpio descriptor rather than
numbers. This allows us to revise the interfaces to permit all GPIOs
to be used with the regulator core.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Correct the the config register for LDO1.
Fixes: 90e7d52627 (regulator: tps65218: Add Regulator driver for
TPS65218 PMIC)
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: <stable@vger.kernel.org> # v3.15
rdev_get_id() returns an int. Convert rid to type int to avoid the
following warnings:
drivers/regulator/tps65218-regulator.c:132:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/regulator/tps65218-regulator.c:146:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
rdev_get_id() returns an int. Convert rid to type int to avoid the
following warnings:
drivers/regulator/tps65217-regulator.c:73:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
drivers/regulator/tps65217-regulator.c:87:10: warning: comparison of unsigned expression < 0 is always false [-Wtype-limits]
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
'name' field was re-initialized and getting overwritten in some
cases possibly due to a typo. Code inspection says the second time
it should be 'sname' instead of 'name'. Replace it.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Reviewed-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When setting up .enable_reg for an SMPS regulator, presumably we should
call PALMAS_BASE_TO_REG(PALMAS_SMPS_BASE, ...) rather than using
LDO_BASE. This change makes the LCD panel and HDMI work again on the
NVIDIA Dalmore board anyway.
Fixes: 318dbb02b5 ("regulator: palmas: Fix SMPS enable/disable/is_enabled")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Shift the reg_info structure definition to the header file.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The vbus regulator was not getting its name set. This results
in the sysfs entry being empty. The lack of a bcm590xx_regs[]
table entry also upsets Coverity runs. Add the table entry
so the name gets set properly.
Signed-off-by: Graham Williams <graham.williams@linaro.org>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
CONFIG_REGULATOR_AB8500_DEBUG is always not defined.
ab8500_regulator_debug_init() is not called at all now,
ab8500_regulator_debug_exit() simply return 0, thus remove them.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Now this is a DT-only driver because non-devicetree probe path is removed,
so merge ab8500_regulator_of_probe() into ab8500_regulator_probe().
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
'ltc3589_reg_defaults' is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
We use regmap regulator ops to enable/disable and check if regulator
is enabled for various SMPS. However, these depend on valid
enable_reg, enable_mask and enable_value in regulator descriptor.
Currently we do not populate these for SMPS other than SMPS10, this
results in spurious results as regmap assumes that the values are
valid and ends up reading register 0x0 RTC:SECONDS_REG on Palmas
variants that do have RTC! To fix this, we update proper parameters
for the descriptor fields.
Further, we want to ensure the behavior consistent with logic
prior to commit dbabd624d4, where, once you do a set_mode,
enable/disable ensure the logic remains consistent and configures
Palmas to the configuration that we set with set_mode (since the
configuration register is common). To do this, we can rely on the
regulator core's regulator_register behavior where the regulator
descriptor pointer provided by the regulator driver is stored. (no
reallocation and copy is done). This lets us update the enable_value
post registration, to remain consistent with the mode we configure as
part of set_mode.
Fixes: dbabd624d4 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Tested-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch removes wrapper functions used to access regmap, and
make driver using regmap_*() functions instead.
Signed-off-by: Robert Baldyga <r.baldyga@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Mark Brown <broonie@linaro.org>
Acked-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
of_find_node_by_name() walks the allnodes list, and can thus walk
outside of the parent node. Use of_get_child_by_name() instead.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
re-add the perm check (we unified the module param and sysfs checks, but
the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args().
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=IxSN
-----END PGP SIGNATURE-----
Merge tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull module updates from Rusty Russell:
"Most of this is cleaning up various driver sysfs permissions so we can
re-add the perm check (we unified the module param and sysfs checks,
but the module ones were stronger so we weakened them temporarily).
Param parsing gets documented, and also "--" now forces args to be
handed to init (and ignored by the kernel).
Module NX/RO protections get tightened: we now set them before calling
parse_args()"
* tag 'modules-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
module: set nx before marking module MODULE_STATE_COMING.
samples/kobject/: avoid world-writable sysfs files.
drivers/hid/hid-picolcd_fb: avoid world-writable sysfs files.
drivers/staging/speakup/: avoid world-writable sysfs files.
drivers/regulator/virtual: avoid world-writable sysfs files.
drivers/scsi/pm8001/pm8001_ctl.c: avoid world-writable sysfs files.
drivers/hid/hid-lg4ff.c: avoid world-writable sysfs files.
drivers/video/fbdev/sm501fb.c: avoid world-writable sysfs files.
drivers/mtd/devices/docg3.c: avoid world-writable sysfs files.
speakup: fix incorrect perms on speakup_acntsa.c
cpumask.h: silence warning with -Wsign-compare
Documentation: Update kernel-parameters.tx
param: hand arguments after -- straight to init
modpost: Fix resource leak in read_dump()
The PM800_BUCK3 define is cut and pasted twice so we can remove the
second instance.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Read-modify-write sequence is already protected by regmap, so no
additional locks need. This patch remove such locks from mc13xxx
regulator driver.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
Field "hi_bit" is not used anywhere in the driver.
This patch removes this excess field.
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Mark Brown <broonie@linaro.org>
The voltage tables for dvm/ldo4/sw2 are actually linear mapping.
Thus convert dvm/ldo4/sw2 to use regulator_list_voltage_linear.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The site-specific OOM messages are unnecessary, because they
duplicate the MM subsystem generic OOM message.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Acked-by: Matt Porter <mporter@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
get_voltage_sel reads from SMPS register - if the read selector value
is 0, the SMPS is actually disabled - So, this is in addition to the
ctrl_register that may also be used to enable/disable the SMPS.
The original logic(prior to commit dbabd624d4) used to be:
static int palmas_map_voltage_smps(struct regulator_dev *rdev,
int min_uV, int max_uV)
<snip>
if (min_uV == 0)
return 0;
To handle this scenario, with the transition to regulator_list
implementation, we seem to have missed the data necessary to mark as
one of the valid entries as "0" 'disabled regulator' which results in
0 volts - So, stick with pre-existing logic.
Without this added to the list, palmas regulator driver,
on probe, attempts to setup constraints and in the case of
OMAP5uEVM, SMPS9 (which is mapped for 2v1 audio supply) fails in
regulator_list_voltage_linear_range mapping of '0', and as a fall back
of constraints not being applied, the entire regulator list is not
enumerated due to assumption that something system wide has gone bad
on with the PMIC.
Fixes: dbabd624d4 ("regulator: palmas: Reemove open coded functions with helper functions")
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With commit 064d5cd110
(regulator: core: Fix the init of DT defined fixed regulators)
We ensure that regulator must be capable of providing it's current
voltage when constraints are used, however adding the return value in
the print is a little more informative to explain the nature of the
failure involved.
So, instead of providing message such as:
smps9: failed to get the current voltage
having error value added to the message such as:
smps9: failed to get the current voltage(-22)
is a little more informative for debugging the error.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- Move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- Fixes reference counting of the DT nodes for constraints from Charles
Keepax. This has little practical impact since all real users of
the regulator bindings use FDT which doesn't need the reference
counting.
- Lots of cleanups, especially to the Samsung drivers.
- Support for Linear Technologies LTC3589, Texas Instruments TPS658640
and X-Powers AXP20x.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=JrfM
-----END PGP SIGNATURE-----
Merge tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator into next
Pull regulator updates from Mark Brown:
"The bulk of the changes for this release are a few new drivers however
there are a couple of noticable core changes and the usual stream of
cleanups and fixes:
- move disable of unused regulators later in init so it comes after
deferred probe has iterated making startup smoother.
- fixes to reference counting of the DT nodes for constraints from
Charles Keepax. This has little practical impact since all real
users of the regulator bindings use FDT which doesn't need the
reference counting.
- lots of cleanups, especially to the Samsung drivers.
- support for Linear Technologies LTC3589, Texas Instruments
TPS658640 and X-Powers AXP20x"
* tag 'regulator-v3.16' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (64 commits)
regulator: pbias: remove unnecessary OOM messages
regulator: max8649: remove unnecessary OOM messages
regulator: core: Fix the init of DT defined fixed regulators
regulator: core: Disable unused regulators after deferred probing is done
regulator: Don't disable unused regulators we don't have permission for
regulator: axp20x: Use regulator_map_voltage_ascend for LDO4
regulator: use of_property_read_{bool|u32}()
regulator: Fix regulator_get_{optional,exclusive}() documentation
regulators: Add definition of regulator_set_voltage_time() for !CONFIG_REGULATOR
regulator: arizona-ldo1: add missing #include
regulator: pfuze100: Support enable/disable for fixed regulator
regulator: ltc3589: Remove ltc3589_list_voltage_fixed function
regulator: ltc3589: Fix module dependency
regulator: tps6586x: Remove unused to_tps6586x_dev() function
regulator: tps65218: Convert to use regulator_set_voltage_time_sel
regulator: tps6586x: Add support for the TPS658640
regulator: tps6586x: Prepare supporting fixed regulators
regulator: pfuze100: Don't allocate an invalid gpio
regulator: pfuze100: Support SWB enable/disable
regulator: fixed: use of_property_read_{bool|u32}()
...
As of commit 064d5cd110 (regulator: core: Fix the init of DT defined
fixed regulators) the regulator core tries to query the current voltage
of a regulator when applying constraints. This exposes a bug in the
AS3722 regulator driver which fails to read the voltage of disabled
regulators. The reason is that the hardware is programmed to a selector
of 0, but none of the voltage tables include 0 as a valid selector. The
datasheets indicate that 0 is a valid selector when the regulators are
powered off.
To fix this, add a range including selector 0 to the voltage tables.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Here is the big char / misc driver updates for 3.16-rc1.
Lots of different driver updates for a variety of different drivers and
minor driver subsystems.
All have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iEYEABECAAYFAlONWI8ACgkQMUfUDdst+ykvQACdGxTChdEU7edElDAXeelVmu8v
D1UAoLDvqwUsN7t5v+WG2wkOvhf5MEA7
=tVMP
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc into next
Pull char/misc driver patches from Greg KH:
"Here is the big char / misc driver update for 3.16-rc1.
Lots of different driver updates for a variety of different drivers
and minor driver subsystems.
All have been in linux-next with no reported issues"
* tag 'char-misc-3.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (79 commits)
hv: use correct order when freeing monitor_pages
spmi: of: fixup generic SPMI devicetree binding example
applicom: dereferencing NULL on error path
misc: genwqe: fix uninitialized return value in genwqe_free_sync_sgl()
miscdevice.h: Simple syntax fix to make pointers consistent.
MAINTAINERS: Add miscdevice.h to file list for char/misc drivers.
mcb: Add support for shared PCI IRQs
drivers: Remove duplicate conditionally included subdirs
misc: atmel_pwm: only build for supported platforms
mei: me: move probe quirk to cfg structure
mei: add per device configuration
mei: me: read H_CSR after asserting reset
mei: me: drop harmful wait optimization
mei: me: fix hw ready reset flow
mei: fix memory leak of mei_clients array
uio: fix vma io range check in mmap
drivers: uio_dmem_genirq: Fix memory leak in uio_dmem_genirq_probe()
w1: do not unlock unheld list_mutex in __w1_remove_master_device()
w1: optional bundling of netlink kernel replies
connector: allow multiple messages to be sent in one packet
...
Beniamino Galvani