A semicolon is not needed after a switch statement.
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
It is better to explicitly include the required header file rather
then get it through some recursive include.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
There are more and more requirements of building SoC specific drivers
as modules, add support for building i.MX common clock driver as module
to meet the requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
In order to allow runtime PM, the device needs to be passed on
to the register function. Audiomix clock controller, used on
i.MX8MP and future platforms, registers a pll14xx and has runtime
PM support.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When pll type is invalid, ONLY output error message is NOT enough,
should return error immediately.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Add new frequency entries to pll1443x table to meet different
display settings requirement.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Fixes for clk controllers on qcom msm8998 SoCs
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Adjust composite clk to new way of describing clk parents
- Add a driver for BCLK of Freescale SAI cores
* clk-imx: (32 commits)
clk: imx: Add support for i.MX8MP clock driver
dt-bindings: imx: Add clock binding doc for i.MX8MP
clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
clk: imx: imx8mq: Switch to clk_hw based API
clk: imx: imx8mm: Switch to clk_hw based API
clk: imx: imx8mn: Switch to clk_hw based API
clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
clk: imx: gate3: Switch to clk_hw based API
clk: imx: add hw API imx_clk_hw_mux2_flags
clk: imx: add imx_unregister_hw_clocks
clk: imx: clk-composite-8m: Switch to clk_hw based API
clk: imx: clk-pll14xx: Switch to clk_hw based API
clk: imx7up: Rename the clks to hws
clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
clk: imx: Rename sccg and frac pll register to suggest clk_hw
clk: imx: imx7ulp composite: Rename to show is clk_hw based
clk: imx: pllv2: Switch to clk_hw based API
clk: imx: pllv1: Switch to clk_hw based API
...
* clk-ti:
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
* clk-xilinx:
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
* clk-nvidia:
clk: tegra20/30: Explicitly set parent clock for Video Decoder
clk: tegra20/30: Don't pre-initialize displays parent clock
clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
clk: tegra: Mark fuse clock as critical
* clk-qcom: (35 commits)
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: qcom: Add ipq6018 Global Clock Controller support
clk: qcom: Add DT bindings for ipq6018 gcc clock controller
clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
clk: qcom: rpmh: Add IPA clock for SC7180
clk: qcom: rpmh: skip undefined clocks when registering
clk: qcom: Add video clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
clk: qcom: Add graphics clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
clk: qcom: Add display clock controller driver for SC7180
dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
clk: qcom: alpha-pll: Remove useless read from set rate
...
* clk-freescale:
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
* clk-qoriq:
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
Switch the imx_clk_pll14xx function to clk_hw based API, rename
accordingly and add a macro for clk based legacy. This allows us to
move closer to a clear split between consumer and provider clk APIs.
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The usage of readl_poll_timeout is wrong, the 3rd parameter(cond)
should be "val & LOCK_STATUS" not "val & LOCK_TIMEOUT_US",
It is not check whether the pll locked, LOCK_STATUS reflects the mask,
not LOCK_TIMEOUT_US.
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Cc: <stable@vger.kernel.org>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
DRAM frequency switches are executed in firmware and can change the
configuration of the DRAM PLL outside linux. Mark these CLKs with
CLK_GET_RATE_NOCACHE so we always read back the PLL config registers and
recalculate rates.
In current DRAM frequency tables on 8mm/8mn only the maximum frequency
uses the PLL so it's always configured in the same way. However reading
back the PLL configuration is the correct behavior and allows additional
setpoints in the future.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Fix sparse warnings:
drivers/clk/imx/clk-pll14xx.c:44:37:
warning: symbol 'imx_pll1416x_tbl' was not declared. Should it be static?
drivers/clk/imx/clk-pll14xx.c:57:37:
warning: symbol 'imx_pll1443x_tbl' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Use common 1413X/1416X PLL clock structure to save a lot
of duplicated code on i.MX8MN clock driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
Many i.MX8M SoCs use same 1443X/1416X PLL, such as i.MX8MM,
i.MX8MN and later i.MX8M SoCs, moving these PLL definitions
to pll14xx driver can save a lot of duplicated code on each
platform.
Meanwhile, no need to define PLL clock structure for every
module which uses same type of PLL, e.g., audio/video/dram use
1443X PLL, arm/gpu/vpu/sys use 1416X PLL, define 2 PLL clock
structure for each group is enough.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
The PLL14xx on imx8m can change the S and K parameter without requiring
a reset and relock of the whole PLL.
Fix clk_pll144xx_mp_change register reading and use it for pll1443 as
well since no reset+relock is required on K changes either.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
When registering the PLL, unbypass the PLL.
The PLL has two bypass control bit, BYPASS and EXT_BYPASS.
we will expose EXT_BYPASS to clk driver for mux usage, and keep
BYPASS inside pll14xx usage. The PLL has a restriction that
when M/P change, need to RESET/BYPASS pll to avoid glitch, so
we could not expose BYPASS.
To make it easy for clk driver usage, unbypass PLL which does
not hurt current function.
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-3-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
According to PLL1443XA and PLL1416X spec,
"When BYPASS is 0 and RESETB is changed from 0 to 1, FOUT starts to
output unstable clock until lock time passes. PLL1416X/PLL1443XA may
generate a glitch at FOUT."
So set BYPASS when RESETB is changed from 0 to 1 to avoid glitch.
In the end of set rate, BYPASS will be cleared.
When prepare clock, also need to take care to avoid glitch. So
we also follow Spec to set BYPASS before RESETB changed from 0 to 1.
And add a check if the RESETB is already 0, directly return 0;
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lkml.kernel.org/r/1568043491-20680-2-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
It does not make sense to only get value from pll->base and assign
to a local variable when recalc_rate.
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Code which initializes the "clk_init_data.ops" checks pll->rate_table
before that field is ever assigned to so it always picks
"clk_pll1416x_min_ops".
This breaks dynamic rate rounding for features such as cpufreq.
Fix by checking pll_clk->rate_table instead, here pll_clk refers to
the constant initialization data coming from per-soc clk driver.
Signed-off-by: Leonard Crestez <leonard.crestez@nxp.com>
Fixes: 8646d4dcc7 ("clk: imx: Add PLLs driver for imx8mm soc")
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
New PLLs are introduced on i.MX8M Mini SOC.
PLL1416X is Integer PLL, PLL1443X is a Frac PLL.
Signed-off-by: Bai Ping <ping.bai@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Tom Rix