The bio users should now always be setting up the bio op. This patch
has the block layer copy that to the request.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch converts the simple bi_rw use cases in the block,
drivers, mm and fs code to set/get the bio operation using
bio_set_op_attrs/bio_op
These should be simple one or two liner cases, so I just did them
in one patch. The next patches handle the more complicated
cases in a module per patch.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
We currently set REQ_WRITE/WRITE for all non READ IOs
like discard, flush, writesame, etc. In the next patches where we
no longer set up the op as a bitmap, we will not be able to
detect a operation direction like writesame by testing if REQ_WRITE is
set.
This patch converts the drivers and cgroup to use the
op_is_write helper. This should just cover the simple
cases. I did dm, md and bcache in their own patches
because they were more involved.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This has callers of submit_bio/submit_bio_wait set the bio->bi_rw
instead of passing it in. This makes that use the same as
generic_make_request and how we set the other bio fields.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Fixed up fs/ext4/crypto.c
Signed-off-by: Jens Axboe <axboe@fb.com>
Now that we converted everything to the newer block write cache
interface, kill off the queue flush_flags and queueable flush
entries.
Signed-off-by: Jens Axboe <axboe@fb.com>
We could kmalloc() the payload, so need the offset in page.
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} macros were introduced *long* time
ago with promise that one day it will be possible to implement page
cache with bigger chunks than PAGE_SIZE.
This promise never materialized. And unlikely will.
We have many places where PAGE_CACHE_SIZE assumed to be equal to
PAGE_SIZE. And it's constant source of confusion on whether
PAGE_CACHE_* or PAGE_* constant should be used in a particular case,
especially on the border between fs and mm.
Global switching to PAGE_CACHE_SIZE != PAGE_SIZE would cause to much
breakage to be doable.
Let's stop pretending that pages in page cache are special. They are
not.
The changes are pretty straight-forward:
- <foo> << (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- <foo> >> (PAGE_CACHE_SHIFT - PAGE_SHIFT) -> <foo>;
- PAGE_CACHE_{SIZE,SHIFT,MASK,ALIGN} -> PAGE_{SIZE,SHIFT,MASK,ALIGN};
- page_cache_get() -> get_page();
- page_cache_release() -> put_page();
This patch contains automated changes generated with coccinelle using
script below. For some reason, coccinelle doesn't patch header files.
I've called spatch for them manually.
The only adjustment after coccinelle is revert of changes to
PAGE_CAHCE_ALIGN definition: we are going to drop it later.
There are few places in the code where coccinelle didn't reach. I'll
fix them manually in a separate patch. Comments and documentation also
will be addressed with the separate patch.
virtual patch
@@
expression E;
@@
- E << (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
expression E;
@@
- E >> (PAGE_CACHE_SHIFT - PAGE_SHIFT)
+ E
@@
@@
- PAGE_CACHE_SHIFT
+ PAGE_SHIFT
@@
@@
- PAGE_CACHE_SIZE
+ PAGE_SIZE
@@
@@
- PAGE_CACHE_MASK
+ PAGE_MASK
@@
expression E;
@@
- PAGE_CACHE_ALIGN(E)
+ PAGE_ALIGN(E)
@@
expression E;
@@
- page_cache_get(E)
+ get_page(E)
@@
expression E;
@@
- page_cache_release(E)
+ put_page(E)
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Acked-by: Michal Hocko <mhocko@suse.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull libata updates from Tejun Heo:
- ahci grew runtime power management support so that the controller can
be turned off if no devices are attached.
- sata_via isn't dead yet. It got hotplug support and more refined
workaround for certain WD drives.
- Misc cleanups. There's a merge from for-4.5-fixes to avoid confusing
conflicts in ahci PCI ID table.
* 'for-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
ata: ahci_xgene: dereferencing uninitialized pointer in probe
AHCI: Remove obsolete Intel Lewisburg SATA RAID device IDs
ata: sata_rcar: Use ARCH_RENESAS
sata_via: Implement hotplug for VT6421
sata_via: Apply WD workaround only when needed on VT6421
ahci: Add runtime PM support for the host controller
ahci: Add functions to manage runtime PM of AHCI ports
ahci: Convert driver to use modern PM hooks
ahci: Cache host controller version
scsi: Drop runtime PM usage count after host is added
scsi: Set request queue runtime PM status back to active on resume
block: Add blk_set_runtime_active()
ata: ahci_mvebu: add support for Armada 3700 variant
libata: fix unbalanced spin_lock_irqsave/spin_unlock_irq() in ata_scsi_park_show()
libata: support AHCI on OCTEON platform
Request-based DM's blk-mq support (dm-mq) was reported to be 50% slower
than if an underlying null_blk device were used directly. One of the
reasons for this drop in performance is that blk_insert_clone_request()
was calling blk_mq_insert_request() with @async=true. This forced the
use of kblockd_schedule_delayed_work_on() to run the blk-mq hw queues
which ushered in ping-ponging between process context (fio in this case)
and kblockd's kworker to submit the cloned request. The ftrace
function_graph tracer showed:
kworker-2013 => fio-12190
fio-12190 => kworker-2013
...
kworker-2013 => fio-12190
fio-12190 => kworker-2013
...
Fixing blk_insert_clone_request()'s blk_mq_insert_request() call to
_not_ use kblockd to submit the cloned requests isn't enough to
eliminate the observed context switches.
In addition to this dm-mq specific blk-core fix, there are 2 DM core
fixes to dm-mq that (when paired with the blk-core fix) completely
eliminate the observed context switching:
1) don't blk_mq_run_hw_queues in blk-mq request completion
Motivated by desire to reduce overhead of dm-mq, punting to kblockd
just increases context switches.
In my testing against a really fast null_blk device there was no benefit
to running blk_mq_run_hw_queues() on completion (and no other blk-mq
driver does this). So hopefully this change doesn't induce the need for
yet another revert like commit 621739b00e !
2) use blk_mq_complete_request() in dm_complete_request()
blk_complete_request() doesn't offer the traditional q->mq_ops vs
.request_fn branching pattern that other historic block interfaces
do (e.g. blk_get_request). Using blk_mq_complete_request() for
blk-mq requests is important for performance. It should be noted
that, like blk_complete_request(), blk_mq_complete_request() doesn't
natively handle partial completions -- but the request-based
DM-multipath target does provide the required partial completion
support by dm.c:end_clone_bio() triggering requeueing of the request
via dm-mpath.c:multipath_end_io()'s return of DM_ENDIO_REQUEUE.
dm-mq fix#2 is _much_ more important than #1 for eliminating the
context switches.
Before: cpu : usr=15.10%, sys=59.39%, ctx=7905181, majf=0, minf=475
After: cpu : usr=20.60%, sys=79.35%, ctx=2008, majf=0, minf=472
With these changes multithreaded async read IOPs improved from ~950K
to ~1350K for this dm-mq stacked on null_blk test-case. The raw read
IOPs of the underlying null_blk device for the same workload is ~1950K.
Fixes: 7fb4898e0 ("block: add blk-mq support to blk_insert_cloned_request()")
Fixes: bfebd1cdb ("dm: add full blk-mq support to request-based DM")
Cc: stable@vger.kernel.org # 4.1+
Reported-by: Sagi Grimberg <sagig@dev.mellanox.co.il>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
If block device is left runtime suspended during system suspend, resume
hook of the driver typically corrects runtime PM status of the device back
to "active" after it is resumed. However, this is not enough as queue's
runtime PM status is still "suspended". As long as it is in this state
blk_pm_peek_request() returns NULL and thus prevents new requests to be
processed.
Add new function blk_set_runtime_active() that can be used to force the
queue status back to "active" as needed.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Tejun Heo <tj@kernel.org>
When a storage device rejects a WRITE SAME command we will disable write
same functionality for the device and return -EREMOTEIO to the block
layer. -EREMOTEIO will in turn prevent DM from retrying the I/O and/or
failing the path.
Yiwen Jiang discovered a small race where WRITE SAME requests issued
simultaneously would cause -EIO to be returned. This happened because
any requests being prepared after WRITE SAME had been disabled for the
device caused us to return BLKPREP_KILL. The latter caused the block
layer to return -EIO upon completion.
To overcome this we introduce BLKPREP_INVALID which indicates that this
is an invalid request for the device. blk_peek_request() is modified to
return -EREMOTEIO in that case.
Reported-by: Yiwen Jiang <jiangyiwen@huawei.com>
Suggested-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Hannes Reinicke <hare@suse.de>
Reviewed-by: Ewan Milne <emilne@redhat.com>
Reviewed-by: Yiwen Jiang <jiangyiwen@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pull NVMe updates from Jens Axboe:
"Last branch for this series is the nvme changes. It's in a separate
branch to avoid splitting too much between core and NVMe changes,
since NVMe is still helping drive some blk-mq changes. That said, not
a huge amount of core changes in here. The grunt of the work is the
continued split of the code"
* 'for-4.5/nvme' of git://git.kernel.dk/linux-block: (67 commits)
uapi: update install list after nvme.h rename
NVMe: Export NVMe attributes to sysfs group
NVMe: Shutdown controller only for power-off
NVMe: IO queue deletion re-write
NVMe: Remove queue freezing on resets
NVMe: Use a retryable error code on reset
NVMe: Fix admin queue ring wrap
nvme: make SG_IO support optional
nvme: fixes for NVME_IOCTL_IO_CMD on the char device
nvme: synchronize access to ctrl->namespaces
nvme: Move nvme_freeze/unfreeze_queues to nvme core
PCI/AER: include header file
NVMe: Export namespace attributes to sysfs
NVMe: Add pci error handlers
block: remove REQ_NO_TIMEOUT flag
nvme: merge iod and cmd_info
nvme: meta_sg doesn't have to be an array
nvme: properly free resources for cancelled command
nvme: simplify completion handling
nvme: special case AEN requests
...
Pull core block updates from Jens Axboe:
"We don't have a lot of core changes this time around, it's mostly in
drivers, which will come in a subsequent pull.
The cores changes include:
- blk-mq
- Prep patch from Christoph, changing blk_mq_alloc_request() to
take flags instead of just using gfp_t for sleep/nosleep.
- Doc patch from me, clarifying the difference between legacy
and blk-mq for timer usage.
- Fixes from Raghavendra for memory-less numa nodes, and a reuse
of CPU masks.
- Cleanup from Geliang Tang, using offset_in_page() instead of open
coding it.
- From Ilya, rename request_queue slab to it reflects what it holds,
and a fix for proper use of bdgrab/put.
- A real fix for the split across stripe boundaries from Keith. We
yanked a broken version of this from 4.4-rc final, this one works.
- From Mike Krinkin, emit a trace message when we split.
- From Wei Tang, two small cleanups, not explicitly clearing memory
that is already cleared"
* 'for-4.5/core' of git://git.kernel.dk/linux-block:
block: use bd{grab,put}() instead of open-coding
block: split bios to max possible length
block: add call to split trace point
blk-mq: Avoid memoryless numa node encoded in hctx numa_node
blk-mq: Reuse hardware context cpumask for tags
blk-mq: add a flags parameter to blk_mq_alloc_request
Revert "blk-flush: Queue through IO scheduler when flush not required"
block: clarify blk_add_timer() use case for blk-mq
bio: use offset_in_page macro
block: do not initialise statics to 0 or NULL
block: do not initialise globals to 0 or NULL
block: rename request_queue slab cache
We currently only have an inline/sync helper to restart a stopped
queue. If drivers need an async version, they have to roll their
own. Add a generic helper instead.
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_queue_bio() does split then bounce, which makes the segment
counting based on pages before bouncing and could go wrong. Move
the split to after bouncing, like we do for blk-mq, and the we
fix the issue of having the bio count for segments be wrong.
Fixes: 54efd50bfd ("block: make generic_make_request handle arbitrarily sized bios")
Cc: stable@vger.kernel.org
Tested-by: Artem S. Tashkinov <t.artem@lycos.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Timer context is not very useful for drivers to perform any meaningful abort
action from. So instead of calling the driver from this useless context
defer it to a workqueue as soon as possible.
Note that while a delayed_work item would seem the right thing here I didn't
dare to use it due to the magic in blk_add_timer that pokes deep into timer
internals. But maybe this encourages Tejun to add a sensible API for that to
the workqueue API and we'll all be fine in the end :)
Contains a major update from Keith Bush:
"This patch removes synchronizing the timeout work so that the timer can
start a freeze on its own queue. The timer enters the queue, so timer
context can only start a freeze, but not wait for frozen."
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The routines in scsi_pm.c assume that if a runtime-PM callback is
invoked for a SCSI device, it can only mean that the device's driver
has asked the block layer to handle the runtime power management (by
calling blk_pm_runtime_init(), which among other things sets q->dev).
However, this assumption turns out to be wrong for things like the ses
driver. Normally ses devices are not allowed to do runtime PM, but
userspace can override this setting. If this happens, the kernel gets
a NULL pointer dereference when blk_post_runtime_resume() tries to use
the uninitialized q->dev pointer.
This patch fixes the problem by checking q->dev in block layer before
handle runtime PM. Since ses doesn't define any PM callbacks and call
blk_pm_runtime_init(), the crash won't occur.
This fixes Bugzilla #101371.
https://bugzilla.kernel.org/show_bug.cgi?id=101371
More discussion can be found from below link.
http://marc.info/?l=linux-scsi&m=144163730531875&w=2
Signed-off-by: Ken Xue <Ken.Xue@amd.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: Xiangliang Yu <Xiangliang.Yu@amd.com>
Cc: James E.J. Bottomley <JBottomley@odin.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Michael Terry <Michael.terry@canonical.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
We already have the reserved flag, and a nowait flag awkwardly encoded as
a gfp_t. Add a real flags argument to make the scheme more extensible and
allow for a nicer calling convention.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
When a cloned request is retried on other queues it always needs
to be checked against the queue limits of that queue.
Otherwise the calculations for nr_phys_segments might be wrong,
leading to a crash in scsi_init_sgtable().
To clarify this the patch renames blk_rq_check_limits()
to blk_cloned_rq_check_limits() and removes the symbol
export, as the new function should only be used for
cloned requests and never exported.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Ewan Milne <emilne@redhat.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Fixes: e2a60da74 ("block: Clean up special command handling logic")
Cc: stable@vger.kernel.org # 3.7+
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes the checkpatch.pl error to blk-exec.c:
ERROR: do not initialise globals to 0 or NULL
Signed-off-by: Wei Tang <tangwei@cmss.chinamobile.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Fix kernel-doc warning in blk-core.c:
Warning(..//block/blk-core.c:1549): No description found for parameter 'same_queue_rq'
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block IO poll support from Jens Axboe:
"Various groups have been doing experimentation around IO polling for
(really) fast devices. The code has been reviewed and has been
sitting on the side for a few releases, but this is now good enough
for coordinated benchmarking and further experimentation.
Currently O_DIRECT sync read/write are supported. A framework is in
the works that allows scalable stats tracking so we can auto-tune
this. And we'll add libaio support as well soon. Fow now, it's an
opt-in feature for test purposes"
* 'for-4.4/io-poll' of git://git.kernel.dk/linux-block:
direct-io: be sure to assign dio->bio_bdev for both paths
directio: add block polling support
NVMe: add blk polling support
block: add block polling support
blk-mq: return tag/queue combo in the make_request_fn handlers
block: change ->make_request_fn() and users to return a queue cookie
Add basic support for polling for specific IO to complete. This uses
the cookie that blk-mq passes back, which enables the block layer
to pass this cookie to the driver to spin for a specific request.
This will be combined with request latency tracking, so we can make
qualified decisions about when to poll and when not to. For now, for
benchmark purposes, we add a sysfs file that controls whether polling
is enabled or not.
Signed-off-by: Jens Axboe <axboe@fb.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
No functional changes in this patch, but it prepares us for returning
a more useful cookie related to the IO that was queued up.
Signed-off-by: Jens Axboe <axboe@fb.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Acked-by: Keith Busch <keith.busch@intel.com>
__GFP_WAIT was used to signal that the caller was in atomic context and
could not sleep. Now it is possible to distinguish between true atomic
context and callers that are not willing to sleep. The latter should
clear __GFP_DIRECT_RECLAIM so kswapd will still wake. As clearing
__GFP_WAIT behaves differently, there is a risk that people will clear the
wrong flags. This patch renames __GFP_WAIT to __GFP_RECLAIM to clearly
indicate what it does -- setting it allows all reclaim activity, clearing
them prevents it.
[akpm@linux-foundation.org: fix build]
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Acked-by: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
__GFP_WAIT has been used to identify atomic context in callers that hold
spinlocks or are in interrupts. They are expected to be high priority and
have access one of two watermarks lower than "min" which can be referred
to as the "atomic reserve". __GFP_HIGH users get access to the first
lower watermark and can be called the "high priority reserve".
Over time, callers had a requirement to not block when fallback options
were available. Some have abused __GFP_WAIT leading to a situation where
an optimisitic allocation with a fallback option can access atomic
reserves.
This patch uses __GFP_ATOMIC to identify callers that are truely atomic,
cannot sleep and have no alternative. High priority users continue to use
__GFP_HIGH. __GFP_DIRECT_RECLAIM identifies callers that can sleep and
are willing to enter direct reclaim. __GFP_KSWAPD_RECLAIM to identify
callers that want to wake kswapd for background reclaim. __GFP_WAIT is
redefined as a caller that is willing to enter direct reclaim and wake
kswapd for background reclaim.
This patch then converts a number of sites
o __GFP_ATOMIC is used by callers that are high priority and have memory
pools for those requests. GFP_ATOMIC uses this flag.
o Callers that have a limited mempool to guarantee forward progress clear
__GFP_DIRECT_RECLAIM but keep __GFP_KSWAPD_RECLAIM. bio allocations fall
into this category where kswapd will still be woken but atomic reserves
are not used as there is a one-entry mempool to guarantee progress.
o Callers that are checking if they are non-blocking should use the
helper gfpflags_allow_blocking() where possible. This is because
checking for __GFP_WAIT as was done historically now can trigger false
positives. Some exceptions like dm-crypt.c exist where the code intent
is clearer if __GFP_DIRECT_RECLAIM is used instead of the helper due to
flag manipulations.
o Callers that built their own GFP flags instead of starting with GFP_KERNEL
and friends now also need to specify __GFP_KSWAPD_RECLAIM.
The first key hazard to watch out for is callers that removed __GFP_WAIT
and was depending on access to atomic reserves for inconspicuous reasons.
In some cases it may be appropriate for them to use __GFP_HIGH.
The second key hazard is callers that assembled their own combination of
GFP flags instead of starting with something like GFP_KERNEL. They may
now wish to specify __GFP_KSWAPD_RECLAIM. It's almost certainly harmless
if it's missed in most cases as other activity will wake kswapd.
Signed-off-by: Mel Gorman <mgorman@techsingularity.net>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Michal Hocko <mhocko@suse.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Vitaly Wool <vitalywool@gmail.com>
Cc: Rik van Riel <riel@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull block integrity updates from Jens Axboe:
""This is the joint work of Dan and Martin, cleaning up and improving
the support for block data integrity"
* 'for-4.4/integrity' of git://git.kernel.dk/linux-block:
block, libnvdimm, nvme: provide a built-in blk_integrity nop profile
block: blk_flush_integrity() for bio-based drivers
block: move blk_integrity to request_queue
block: generic request_queue reference counting
nvme: suspend i/o during runtime blk_integrity_unregister
md: suspend i/o during runtime blk_integrity_unregister
md, dm, scsi, nvme, libnvdimm: drop blk_integrity_unregister() at shutdown
block: Inline blk_integrity in struct gendisk
block: Export integrity data interval size in sysfs
block: Reduce the size of struct blk_integrity
block: Consolidate static integrity profile properties
block: Move integrity kobject to struct gendisk
Pull core block updates from Jens Axboe:
"This is the core block pull request for 4.4. I've got a few more
topic branches this time around, some of them will layer on top of the
core+drivers changes and will come in a separate round. So not a huge
chunk of changes in this round.
This pull request contains:
- Enable blk-mq page allocation tracking with kmemleak, from Catalin.
- Unused prototype removal in blk-mq from Christoph.
- Cleanup of the q->blk_trace exchange, using cmpxchg instead of two
xchg()'s, from Davidlohr.
- A plug flush fix from Jeff.
- Also from Jeff, a fix that means we don't have to update shared tag
sets at init time unless we do a state change. This cuts down boot
times on thousands of devices a lot with scsi/blk-mq.
- blk-mq waitqueue barrier fix from Kosuke.
- Various fixes from Ming:
- Fixes for segment merging and splitting, and checks, for
the old core and blk-mq.
- Potential blk-mq speedup by marking ctx pending at the end
of a plug insertion batch in blk-mq.
- direct-io no page dirty on kernel direct reads.
- A WRITE_SYNC fix for mpage from Roman"
* 'for-4.4/core' of git://git.kernel.dk/linux-block:
blk-mq: avoid excessive boot delays with large lun counts
blktrace: re-write setting q->blk_trace
blk-mq: mark ctx as pending at batch in flush plug path
blk-mq: fix for trace_block_plug()
block: check bio_mergeable() early before merging
blk-mq: check bio_mergeable() early before merging
block: avoid to merge splitted bio
block: setup bi_phys_segments after splitting
block: fix plug list flushing for nomerge queues
blk-mq: remove unused blk_mq_clone_flush_request prototype
blk-mq: fix waitqueue_active without memory barrier in block/blk-mq-tag.c
fs: direct-io: don't dirtying pages for ITER_BVEC/ITER_KVEC direct read
fs/mpage.c: forgotten WRITE_SYNC in case of data integrity write
block: kmemleak: Track the page allocations for struct request
Request queues with merging disabled will not flush the plug list after
BLK_MAX_REQUEST_COUNT requests have been queued, since the code relies
on blk_attempt_plug_merge to compute the request_count. Fix this by
computing the number of queued requests even for nomerge queues.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since they lack requests to pin the request_queue active, synchronous
bio-based drivers may have in-flight integrity work from
bio_integrity_endio() that is not flushed by blk_freeze_queue(). Flush
that work to prevent races to free the queue and the final usage of the
blk_integrity profile.
This is temporary unless/until bio-based drivers start to generically
take a q_usage_counter reference while a bio is in-flight.
Cc: Martin K. Petersen <martin.petersen@oracle.com>
[martin: fix the CONFIG_BLK_DEV_INTEGRITY=n case]
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Allow pmem, and other synchronous/bio-based block drivers, to fallback
on a per-cpu reference count managed by the core for tracking queue
live/dead state.
The existing per-cpu reference count for the blk_mq case is promoted to
be used in all block i/o scenarios. This involves initializing it by
default, waiting for it to drop to zero at exit, and holding a live
reference over the invocation of q->make_request_fn() in
generic_make_request(). The blk_mq code continues to take its own
reference per blk_mq request and retains the ability to freeze the
queue, but the check that the queue is frozen is moved to
generic_make_request().
This fixes crash signatures like the following:
BUG: unable to handle kernel paging request at ffff880140000000
[..]
Call Trace:
[<ffffffff8145e8bf>] ? copy_user_handle_tail+0x5f/0x70
[<ffffffffa004e1e0>] pmem_do_bvec.isra.11+0x70/0xf0 [nd_pmem]
[<ffffffffa004e331>] pmem_make_request+0xd1/0x200 [nd_pmem]
[<ffffffff811c3162>] ? mempool_alloc+0x72/0x1a0
[<ffffffff8141f8b6>] generic_make_request+0xd6/0x110
[<ffffffff8141f966>] submit_bio+0x76/0x170
[<ffffffff81286dff>] submit_bh_wbc+0x12f/0x160
[<ffffffff81286e62>] submit_bh+0x12/0x20
[<ffffffff813395bd>] jbd2_write_superblock+0x8d/0x170
[<ffffffff8133974d>] jbd2_mark_journal_empty+0x5d/0x90
[<ffffffff813399cb>] jbd2_journal_destroy+0x24b/0x270
[<ffffffff810bc4ca>] ? put_pwq_unlocked+0x2a/0x30
[<ffffffff810bc6f5>] ? destroy_workqueue+0x225/0x250
[<ffffffff81303494>] ext4_put_super+0x64/0x360
[<ffffffff8124ab1a>] generic_shutdown_super+0x6a/0xf0
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Ross Zwisler <ross.zwisler@linux.intel.com>
Suggested-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Tested-by: Ross Zwisler <ross.zwisler@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
bdi's are initialized in two steps, bdi_init() and bdi_register(), but
destroyed in a single step by bdi_destroy() which, for a bdi embedded
in a request_queue, is called during blk_cleanup_queue() which makes
the queue invisible and starts the draining of remaining usages.
A request_queue's user can access the congestion state of the embedded
bdi as long as it holds a reference to the queue. As such, it may
access the congested state of a queue which finished
blk_cleanup_queue() but hasn't reached blk_release_queue() yet.
Because the congested state was embedded in backing_dev_info which in
turn is embedded in request_queue, accessing the congested state after
bdi_destroy() was called was fine. The bdi was destroyed but the
memory region for the congested state remained accessible till the
queue got released.
a13f35e871 ("writeback: don't embed root bdi_writeback_congested in
bdi_writeback") changed the situation. Now, the root congested state
which is expected to be pinned while request_queue remains accessible
is separately reference counted and the base ref is put during
bdi_destroy(). This means that the root congested state may go away
prematurely while the queue is between bdi_dstroy() and
blk_cleanup_queue(), which was detected by Andrey's KASAN tests.
The root cause of this problem is that bdi doesn't distinguish the two
steps of destruction, unregistration and release, and now the root
congested state actually requires a separate release step. To fix the
issue, this patch separates out bdi_unregister() and bdi_exit() from
bdi_destroy(). bdi_unregister() is called from blk_cleanup_queue()
and bdi_exit() from blk_release_queue(). bdi_destroy() is now just a
simple wrapper calling the two steps back-to-back.
While at it, the prototype of bdi_destroy() is moved right below
bdi_setup_and_register() so that the counterpart operations are
located together.
Signed-off-by: Tejun Heo <tj@kernel.org>
Fixes: a13f35e871 ("writeback: don't embed root bdi_writeback_congested in bdi_writeback")
Cc: stable@vger.kernel.org # v4.2+
Reported-and-tested-by: Andrey Konovalov <andreyknvl@google.com>
Link: http://lkml.kernel.org/g/CAAeHK+zUJ74Zn17=rOyxacHU18SgCfC6bsYW=6kCY5GXJBwGfQ@mail.gmail.com
Reviewed-by: Jan Kara <jack@suse.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull blk-cg updates from Jens Axboe:
"A bit later in the cycle, but this has been in the block tree for a a
while. This is basically four patchsets from Tejun, that improve our
buffered cgroup writeback. It was dependent on the other cgroup
changes, but they went in earlier in this cycle.
Series 1 is set of 5 patches that has cgroup writeback updates:
- bdi_writeback iteration fix which could lead to some wb's being
skipped or repeated during e.g. sync under memory pressure.
- Simplification of wb work wait mechanism.
- Writeback tracepoints updated to report cgroup.
Series 2 is is a set of updates for the CFQ cgroup writeback handling:
cfq has always charged all async IOs to the root cgroup. It didn't
have much choice as writeback didn't know about cgroups and there
was no way to tell who to blame for a given writeback IO.
writeback finally grew support for cgroups and now tags each
writeback IO with the appropriate cgroup to charge it against.
This patchset updates cfq so that it follows the blkcg each bio is
tagged with. Async cfq_queues are now shared across cfq_group,
which is per-cgroup, instead of per-request_queue cfq_data. This
makes all IOs follow the weight based IO resource distribution
implemented by cfq.
- Switched from GFP_ATOMIC to GFP_NOWAIT as suggested by Jeff.
- Other misc review points addressed, acks added and rebased.
Series 3 is the blkcg policy cleanup patches:
This patchset contains assorted cleanups for blkcg_policy methods
and blk[c]g_policy_data handling.
- alloc/free added for blkg_policy_data. exit dropped.
- alloc/free added for blkcg_policy_data.
- blk-throttle's async percpu allocation is replaced with direct
allocation.
- all methods now take blk[c]g_policy_data instead of blkcg_gq or
blkcg.
And finally, series 4 is a set of patches cleaning up the blkcg stats
handling:
blkcg's stats have always been somwhat of a mess. This patchset
tries to improve the situation a bit.
- The following patches added to consolidate blkcg entry point and
blkg creation. This is in itself is an improvement and helps
colllecting common stats on bio issue.
- per-blkg stats now accounted on bio issue rather than request
completion so that bio based and request based drivers can behave
the same way. The issue was spotted by Vivek.
- cfq-iosched implements custom recursive stats and blk-throttle
implements custom per-cpu stats. This patchset make blkcg core
support both by default.
- cfq-iosched and blk-throttle keep track of the same stats
multiple times. Unify them"
* 'for-4.3/blkcg' of git://git.kernel.dk/linux-block: (45 commits)
blkcg: use CGROUP_WEIGHT_* scale for io.weight on the unified hierarchy
blkcg: s/CFQ_WEIGHT_*/CFQ_WEIGHT_LEGACY_*/
blkcg: implement interface for the unified hierarchy
blkcg: misc preparations for unified hierarchy interface
blkcg: separate out tg_conf_updated() from tg_set_conf()
blkcg: move body parsing from blkg_conf_prep() to its callers
blkcg: mark existing cftypes as legacy
blkcg: rename subsystem name from blkio to io
blkcg: refine error codes returned during blkcg configuration
blkcg: remove unnecessary NULL checks from __cfqg_set_weight_device()
blkcg: reduce stack usage of blkg_rwstat_recursive_sum()
blkcg: remove cfqg_stats->sectors
blkcg: move io_service_bytes and io_serviced stats into blkcg_gq
blkcg: make blkg_[rw]stat_recursive_sum() to be able to index into blkcg_gq
blkcg: make blkcg_[rw]stat per-cpu
blkcg: add blkg_[rw]stat->aux_cnt and replace cfq_group->dead_stats with it
blkcg: consolidate blkg creation in blkcg_bio_issue_check()
blk-throttle: improve queue bypass handling
blkcg: move root blkg lookup optimization from throtl_lookup_tg() to __blkg_lookup()
blkcg: inline [__]blkg_lookup()
...
blkg (blkcg_gq) currently is created by blkcg policies invoking
blkg_lookup_create() which ends up repeating about the same code in
different policies. Theoretically, this can avoid the overhead of
looking and/or creating blkg's if blkcg is enabled but no policy is in
use; however, the cost of blkg lookup / creation is very low
especially if only the root blkcg is in use which is highly likely if
no blkcg policy is in active use - it boils down to a single very
predictable conditional and surrounding RCU protection.
This patch consolidates blkg creation to a new function
blkcg_bio_issue_check() which is called during bio issue from
generic_make_request_checks(). blkcg_bio_issue_check() is now the
only function which tries to create missing blkg's. The subsequent
policy and request_list operations just perform blkg_lookup() and if
missing falls back to the root.
* blk_get_rl() no longer tries to create blkg. It uses blkg_lookup()
instead of blkg_lookup_create().
* blk_throtl_bio() is now called from blkcg_bio_issue_check() with rcu
read locked and blkg already looked up. Both throtl_lookup_tg() and
throtl_lookup_create_tg() are dropped.
* cfq is similarly updated. cfq_lookup_create_cfqg() is replaced with
cfq_lookup_cfqg()which uses blkg_lookup().
This consolidates blkg handling and avoids unnecessary blkg creation
retries under memory pressure. In addition, this provides a common
bio entry point into blkcg where things like common accounting can be
performed.
v2: Build fixes for !CONFIG_CFQ_GROUP_IOSCHED and
!CONFIG_BLK_DEV_THROTTLING.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Arianna Avanzini <avanzini.arianna@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The way the block layer is currently written, it goes to great lengths
to avoid having to split bios; upper layer code (such as bio_add_page())
checks what the underlying device can handle and tries to always create
bios that don't need to be split.
But this approach becomes unwieldy and eventually breaks down with
stacked devices and devices with dynamic limits, and it adds a lot of
complexity. If the block layer could split bios as needed, we could
eliminate a lot of complexity elsewhere - particularly in stacked
drivers. Code that creates bios can then create whatever size bios are
convenient, and more importantly stacked drivers don't have to deal with
both their own bio size limitations and the limitations of the
(potentially multiple) devices underneath them. In the future this will
let us delete merge_bvec_fn and a bunch of other code.
We do this by adding calls to blk_queue_split() to the various
make_request functions that need it - a few can already handle arbitrary
size bios. Note that we add the call _after_ any call to
blk_queue_bounce(); this means that blk_queue_split() and
blk_recalc_rq_segments() don't need to be concerned with bouncing
affecting segment merging.
Some make_request_fn() callbacks were simple enough to audit and verify
they don't need blk_queue_split() calls. The skipped ones are:
* nfhd_make_request (arch/m68k/emu/nfblock.c)
* axon_ram_make_request (arch/powerpc/sysdev/axonram.c)
* simdisk_make_request (arch/xtensa/platforms/iss/simdisk.c)
* brd_make_request (ramdisk - drivers/block/brd.c)
* mtip_submit_request (drivers/block/mtip32xx/mtip32xx.c)
* loop_make_request
* null_queue_bio
* bcache's make_request fns
Some others are almost certainly safe to remove now, but will be left
for future patches.
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: drbd-user@lists.linbit.com
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Jim Paris <jim@jtan.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Oleg Drokin <oleg.drokin@intel.com>
Cc: Andreas Dilger <andreas.dilger@intel.com>
Acked-by: NeilBrown <neilb@suse.de> (for the 'md/md.c' bits)
Acked-by: Mike Snitzer <snitzer@redhat.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Kent Overstreet <kent.overstreet@gmail.com>
[dpark: skip more mq-based drivers, resolve merge conflicts, etc.]
Signed-off-by: Dongsu Park <dpark@posteo.net>
Signed-off-by: Ming Lin <ming.l@ssi.samsung.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Some places use helpers now, others don't. We only have the 'is set'
helper, add helpers for setting and clearing flags too.
It was a bit of a mess of atomic vs non-atomic access. With
BIO_UPTODATE gone, we don't have any risk of concurrent access to the
flags. So relax the restriction and don't make any of them atomic. The
flags that do have serialization issues (reffed and chained), we
already handle those separately.
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
ability to handle partial request completions -- otherwise with the
current SCSI LLDs these changes could lead to silent data corruption.
- Fix two DM version bumps that were missing from the initial 4.2 DM
pull request (enabled userspace lvm2 to know certain changes have been
made).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVjWetAAoJEMUj8QotnQNaEngIAMVwExw0u04jqoW9rUwLDbpr
PS2A4lh/MGtMqGGPwJp5qiwnKkgQ5/FcxRpslNQYqA6KrIlnjWJhacWl7tOrwqxn
+WBsHIUwjcpwK2RqxSS3Petb6xDd7A3LfTQVhKV9xKZpZp8Y25a+1MPmUYKsFLBH
DJ1d9bXPMdN1qjBXBU1rKkVxj6z8iNz/lv24eN0MGyWhfUUTc8lQg3eey3L0BzCc
siOuupFQXaWIkbawLZrmvPPNm1iMoABC1OPZCTB1AYZYx1rqzEGUR1nZN+qWf6Wf
rZtAPZehbRzvOaf5jC6tEfAcTF23aPEyp4LD+aAQpbuC/1IBi8a3S8z6PvR5EjA=
=QY48
-----END PGP SIGNATURE-----
Merge tag 'dm-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
"Apologies for not pressing this request-based DM partial completion
issue further, it was an oversight on my part. We'll have to get it
fixed up properly and revisit for a future release.
- Revert block and DM core changes the removed request-based DM's
ability to handle partial request completions -- otherwise with the
current SCSI LLDs these changes could lead to silent data
corruption.
- Fix two DM version bumps that were missing from the initial 4.2 DM
pull request (enabled userspace lvm2 to know certain changes have
been made)"
* tag 'dm-4.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache policy smq: fix "default" version to be 1.4.0
dm: bump the ioctl version to 4.32.0
Revert "block, dm: don't copy bios for request clones"
Revert "dm: do not allocate any mempools for blk-mq request-based DM"
This reverts commit 5f1b670d0b.
Justification for revert as reported in this dm-devel post:
https://www.redhat.com/archives/dm-devel/2015-June/msg00160.html
this change should not be pushed to mainline yet.
Firstly, Christoph has a newer version of the patch that fixes silent
data corruption problem:
https://www.redhat.com/archives/dm-devel/2015-May/msg00229.html
And the new version still depends on LLDDs to always complete requests
to the end when error happens, while block API doesn't enforce such a
requirement. If the assumption is ever broken, the inconsistency between
request and bio (e.g. rq->__sector and rq->bio) will cause silent data
corruption:
https://www.redhat.com/archives/dm-devel/2015-June/msg00022.html
Reported-by: Junichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Pull cgroup writeback support from Jens Axboe:
"This is the big pull request for adding cgroup writeback support.
This code has been in development for a long time, and it has been
simmering in for-next for a good chunk of this cycle too. This is one
of those problems that has been talked about for at least half a
decade, finally there's a solution and code to go with it.
Also see last weeks writeup on LWN:
http://lwn.net/Articles/648292/"
* 'for-4.2/writeback' of git://git.kernel.dk/linux-block: (85 commits)
writeback, blkio: add documentation for cgroup writeback support
vfs, writeback: replace FS_CGROUP_WRITEBACK with SB_I_CGROUPWB
writeback: do foreign inode detection iff cgroup writeback is enabled
v9fs: fix error handling in v9fs_session_init()
bdi: fix wrong error return value in cgwb_create()
buffer: remove unusued 'ret' variable
writeback: disassociate inodes from dying bdi_writebacks
writeback: implement foreign cgroup inode bdi_writeback switching
writeback: add lockdep annotation to inode_to_wb()
writeback: use unlocked_inode_to_wb transaction in inode_congested()
writeback: implement unlocked_inode_to_wb transaction and use it for stat updates
writeback: implement [locked_]inode_to_wb_and_lock_list()
writeback: implement foreign cgroup inode detection
writeback: make writeback_control track the inode being written back
writeback: relocate wb[_try]_get(), wb_put(), inode_{attach|detach}_wb()
mm: vmscan: disable memcg direct reclaim stalling if cgroup writeback support is in use
writeback: implement memcg writeback domain based throttling
writeback: reset wb_domain->dirty_limit[_tstmp] when memcg domain size changes
writeback: implement memcg wb_domain
writeback: update wb_over_bg_thresh() to use wb_domain aware operations
...
Pull core block IO update from Jens Axboe:
"Nothing really major in here, mostly a collection of smaller
optimizations and cleanups, mixed with various fixes. In more detail,
this contains:
- Addition of policy specific data to blkcg for block cgroups. From
Arianna Avanzini.
- Various cleanups around command types from Christoph.
- Cleanup of the suspend block I/O path from Christoph.
- Plugging updates from Shaohua and Jeff Moyer, for blk-mq.
- Eliminating atomic inc/dec of both remaining IO count and reference
count in a bio. From me.
- Fixes for SG gap and chunk size support for data-less (discards)
IO, so we can merge these better. From me.
- Small restructuring of blk-mq shared tag support, freeing drivers
from iterating hardware queues. From Keith Busch.
- A few cfq-iosched tweaks, from Tahsin Erdogan and me. Makes the
IOPS mode the default for non-rotational storage"
* 'for-4.2/core' of git://git.kernel.dk/linux-block: (35 commits)
cfq-iosched: fix other locations where blkcg_to_cfqgd() can return NULL
cfq-iosched: fix sysfs oops when attempting to read unconfigured weights
cfq-iosched: move group scheduling functions under ifdef
cfq-iosched: fix the setting of IOPS mode on SSDs
blktrace: Add blktrace.c to BLOCK LAYER in MAINTAINERS file
block, cgroup: implement policy-specific per-blkcg data
block: Make CFQ default to IOPS mode on SSDs
block: add blk_set_queue_dying() to blkdev.h
blk-mq: Shared tag enhancements
block: don't honor chunk sizes for data-less IO
block: only honor SG gap prevention for merges that contain data
block: fix returnvar.cocci warnings
block, dm: don't copy bios for request clones
block: remove management of bi_remaining when restoring original bi_end_io
block: replace trylock with mutex_lock in blkdev_reread_part()
block: export blkdev_reread_part() and __blkdev_reread_part()
suspend: simplify block I/O handling
block: collapse bio bit space
block: remove unused BIO_RW_BLOCK and BIO_EOF flags
block: remove BIO_EOPNOTSUPP
...
Now that bdi layer can handle per-blkcg bdi_writeback_congested state,
blk_{set|clear}_congested() can propagate non-root blkcg congestion
state to them.
This can be easily achieved by disabling the root_rl tests in
blk_{set|clear}_congested(). Note that we still need those tests when
!CONFIG_CGROUP_WRITEBACK as otherwise we'll end up flipping root blkcg
wb's congestion state for events happening on other blkcgs.
v2: Updated for bdi_writeback_congested.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jan Kara <jack@suse.cz>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_{set|clear}_queue_congested() take @q and set or clear,
respectively, the congestion state of its bdi's root wb. Because bdi
used to be able to handle congestion state only on the root wb, the
callers of those functions tested whether the congestion is on the
root blkcg and skipped if not.
This is cumbersome and makes implementation of per cgroup
bdi_writeback congestion state propagation difficult. This patch
renames blk_{set|clear}_queue_congested() to
blk_{set|clear}_congested(), and makes them take request_list instead
of request_queue and test whether the specified request_list is the
root one before updating bdi_writeback congestion state. This makes
the tests in the callers unnecessary and simplifies them.
As there are no external users of these functions, the definitions are
moved from include/linux/blkdev.h to block/blk-core.c.
This patch doesn't introduce any noticeable behavior difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jan Kara <jack@suse.cz>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
cgroup writeback requires support from both bdi and filesystem sides.
Add BDI_CAP_CGROUP_WRITEBACK and FS_CGROUP_WRITEBACK to indicate
support and enable BDI_CAP_CGROUP_WRITEBACK on block based bdi's by
default. Also, define CONFIG_CGROUP_WRITEBACK which is enabled if
both MEMCG and BLK_CGROUP are enabled.
inode_cgwb_enabled() which determines whether a given inode's both bdi
and fs support cgroup writeback is added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, a bdi (backing_dev_info) embeds single wb (bdi_writeback)
and the role of the separation is unclear. For cgroup support for
writeback IOs, a bdi will be updated to host multiple wb's where each
wb serves writeback IOs of a different cgroup on the bdi. To achieve
that, a wb should carry all states necessary for servicing writeback
IOs for a cgroup independently.
This patch moves bdi->state into wb.
* enum bdi_state is renamed to wb_state and the prefix of all enums is
changed from BDI_ to WB_.
* Explicit zeroing of bdi->state is removed without adding zeoring of
wb->state as the whole data structure is zeroed on init anyway.
* As there's still only one bdi_writeback per backing_dev_info, all
uses of bdi->state are mechanically replaced with bdi->wb.state
introducing no behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: drbd-dev@lists.linbit.com
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
cgroup aware writeback support will require exposing some of blkcg
details. In preprataion, move block/blk-cgroup.h to
include/linux/blk-cgroup.h. This patch is pure file move.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently dm-multipath has to clone the bios for every request sent
to the lower devices, which wastes cpu cycles and ties down memory.
This patch instead adds a new REQ_CLONE flag that instructs req_bio_endio
to not complete bios attached to a request, which we set on clone
requests similar to bios in a flush sequence. With this change I/O
errors on a path failure only get propagated to dm-multipath, which
can then either resubmit the I/O or complete the bios on the original
request.
I've done some basic testing of this on a Linux target with ALUA support,
and it survives path failures during I/O nicely.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
With commit ff36ab345 ("dm: remove request-based logic from
make_request_fn wrapper") DM no longer calls blk_queue_bio() directly,
so remove its export. Doing so required a forward declaration in
blk-core.c.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Last patch makes plug work for multiple queue case. However it only
works for single disk case, because it assumes only one request in the
plug list. If a task is accessing multiple disks, eg MD/DM, the
assumption is wrong. Let blk_attempt_plug_merge() record request from
the same queue.
V2: use NULL parameter in !mq case. Fix a bug. Add comments in
blk_attempt_plug_merge to make it less (hopefully) confusion.
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Shaohua Li <shli@fb.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Current code looks like inner plug gets flushed with a
blk_finish_plug(). Actually it's a nop. All requests/callbacks are added
to current->plug, while only outmost plug is assigned to current->plug.
So inner plug always has empty request/callback list, which makes
blk_flush_plug_list() a nop. This tries to make the code more clear.
Signed-off-by: Shaohua Li <shli@fb.com>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This removes the request types and hacks from the block code and into the
old IDE driver. There is a small amunt of code duplication due to this,
but it's not too bad.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Because of the peculiar way that md devices are created (automatically
when the device node is opened), a new device can be created and
registered immediately after the
blk_unregister_region(disk_devt(disk), disk->minors);
call in del_gendisk().
Therefore it is important that all visible artifacts of the previous
device are removed before this call. In particular, the 'bdi'.
Since:
commit c4db59d31e
Author: Christoph Hellwig <hch@lst.de>
fs: don't reassign dirty inodes to default_backing_dev_info
moved the
device_unregister(bdi->dev);
call from bdi_unregister() to bdi_destroy() it has been quite easy to
lose a race and have a new (e.g.) "md127" be created after the
blk_unregister_region() call and before bdi_destroy() is ultimately
called by the final 'put_disk', which must come after del_gendisk().
The new device finds that the bdi name is already registered in sysfs
and complains
> [ 9627.630029] WARNING: CPU: 18 PID: 3330 at fs/sysfs/dir.c:31 sysfs_warn_dup+0x5a/0x70()
> [ 9627.630032] sysfs: cannot create duplicate filename '/devices/virtual/bdi/9:127'
We can fix this by moving the bdi_destroy() call out of
blk_release_queue() (which can happen very late when a refcount
reaches zero) and into blk_cleanup_queue() - which happens exactly when the md
device driver calls it.
Then it is only necessary for md to call blk_cleanup_queue() before
del_gendisk(). As loop.c devices are also created on demand by
opening the device node, we make the same change there.
Fixes: c4db59d31e
Reported-by: Azat Khuzhin <a3at.mail@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: stable@vger.kernel.org (v4.0)
Signed-off-by: NeilBrown <neilb@suse.de>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_init_rl() allocates a mempool using mempool_create_node() with node
local memory. This only allocates the mempool and element list locally
to the requeue queue node.
What we really want to do is allocate the request itself local to the
queue. To do this, we need our own alloc and free functions that will
allocate from request_cachep and pass the request queue node in to prefer
node local memory.
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: David Rientjes <rientjes@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull core block IO changes from Jens Axboe:
"This contains:
- A series from Christoph that cleans up and refactors various parts
of the REQ_BLOCK_PC handling. Contributions in that series from
Dongsu Park and Kent Overstreet as well.
- CFQ:
- A bug fix for cfq for realtime IO scheduling from Jeff Moyer.
- A stable patch fixing a potential crash in CFQ in OOM
situations. From Konstantin Khlebnikov.
- blk-mq:
- Add support for tag allocation policies, from Shaohua. This is
a prep patch enabling libata (and other SCSI parts) to use the
blk-mq tagging, instead of rolling their own.
- Various little tweaks from Keith and Mike, in preparation for
DM blk-mq support.
- Minor little fixes or tweaks from me.
- A double free error fix from Tony Battersby.
- The partition 4k issue fixes from Matthew and Boaz.
- Add support for zero+unprovision for blkdev_issue_zeroout() from
Martin"
* 'for-3.20/core' of git://git.kernel.dk/linux-block: (27 commits)
block: remove unused function blk_bio_map_sg
block: handle the null_mapped flag correctly in blk_rq_map_user_iov
blk-mq: fix double-free in error path
block: prevent request-to-request merging with gaps if not allowed
blk-mq: make blk_mq_run_queues() static
dm: fix multipath regression due to initializing wrong request
cfq-iosched: handle failure of cfq group allocation
block: Quiesce zeroout wrapper
block: rewrite and split __bio_copy_iov()
block: merge __bio_map_user_iov into bio_map_user_iov
block: merge __bio_map_kern into bio_map_kern
block: pass iov_iter to the BLOCK_PC mapping functions
block: add a helper to free bio bounce buffer pages
block: use blk_rq_map_user_iov to implement blk_rq_map_user
block: simplify bio_map_kern
block: mark blk-mq devices as stackable
block: keep established cmd_flags when cloning into a blk-mq request
block: add blk-mq support to blk_insert_cloned_request()
block: require blk_rq_prep_clone() be given an initialized clone request
blk-mq: add tag allocation policy
...
blk_mq_alloc_request() may establish REQ_MQ_INFLIGHT in addition to
incrementing the hctx->nr_active count. Any cmd_flags that are
established in the newly allocated clone request must be preserved in
addition to the cmd_flags that are later copied over from the original
request as part of blk_rq_prep_clone().
Otherwise, if REQ_MQ_INFLIGHT isn't set in the clone request the
hctx->nr_active count won't get decremented via blk_mq_free_request().
The only consumer of blk_rq_prep_clone() is request-based DM, which uses
blk_rq_init() prior to calling blk_rq_prep_clone() for the non-blk-mq
case. Given the cloned request's cmd_flags will be 0 it is safe to OR
them with the original request's cmd_flags for both the non-blk-mq and
blk-mq cases.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If the request passed to blk_insert_cloned_request() was allocated by
a blk-mq device it must be submitted using blk_mq_insert_request().
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Prepare to allow blk_rq_prep_clone() to accept clone requests that were
allocated from blk-mq request queues. As such the blk_rq_prep_clone()
caller must first initialize the clone request.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Since "BDI: Provide backing device capability information [try #3]" the
backing_dev_info structure also provides flags for the kind of mmap
operation available in a nommu environment, which is entirely unrelated
to it's original purpose.
Introduce a new nommu-only file operation to provide this information to
the nommu mmap code instead. Splitting this from the backing_dev_info
structure allows to remove lots of backing_dev_info instance that aren't
otherwise needed, and entirely gets rid of the concept of providing a
backing_dev_info for a character device. It also removes the need for
the mtd_inodefs filesystem.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Tejun Heo <tj@kernel.org>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
If it's dying, we can't expect new request to complete and come
in an wake up other tasks waiting for requests. So after we
have marked it as dying, wake up everybody currently waiting
for a request. Once they wake, they will retry their allocation
and fail appropriately due to the state of the queue.
Tested-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block driver core update from Jens Axboe:
"This is the pull request for the core block IO changes for 3.19. Not
a huge round this time, mostly lots of little good fixes:
- Fix a bug in sysfs blktrace interface causing a NULL pointer
dereference, when enabled/disabled through that API. From Arianna
Avanzini.
- Various updates/fixes/improvements for blk-mq:
- A set of updates from Bart, mostly fixing buts in the tag
handling.
- Cleanup/code consolidation from Christoph.
- Extend queue_rq API to be able to handle batching issues of IO
requests. NVMe will utilize this shortly. From me.
- A few tag and request handling updates from me.
- Cleanup of the preempt handling for running queues from Paolo.
- Prevent running of unmapped hardware queues from Ming Lei.
- Move the kdump memory limiting check to be in the correct
location, from Shaohua.
- Initialize all software queues at init time from Takashi. This
prevents a kobject warning when CPUs are brought online that
weren't online when a queue was registered.
- Single writeback fix for I_DIRTY clearing from Tejun. Queued with
the core IO changes, since it's just a single fix.
- Version X of the __bio_add_page() segment addition retry from
Maurizio. Hope the Xth time is the charm.
- Documentation fixup for IO scheduler merging from Jan.
- Introduce (and use) generic IO stat accounting helpers for non-rq
drivers, from Gu Zheng.
- Kill off artificial limiting of max sectors in a request from
Christoph"
* 'for-3.19/core' of git://git.kernel.dk/linux-block: (26 commits)
bio: modify __bio_add_page() to accept pages that don't start a new segment
blk-mq: Fix uninitialized kobject at CPU hotplugging
blktrace: don't let the sysfs interface remove trace from running list
blk-mq: Use all available hardware queues
blk-mq: Micro-optimize bt_get()
blk-mq: Fix a race between bt_clear_tag() and bt_get()
blk-mq: Avoid that __bt_get_word() wraps multiple times
blk-mq: Fix a use-after-free
blk-mq: prevent unmapped hw queue from being scheduled
blk-mq: re-check for available tags after running the hardware queue
blk-mq: fix hang in bt_get()
blk-mq: move the kdump check to blk_mq_alloc_tag_set
blk-mq: cleanup tag free handling
blk-mq: use 'nr_cpu_ids' as highest CPU ID count for hwq <-> cpu map
blk: introduce generic io stat accounting help function
blk-mq: handle the single queue case in blk_mq_hctx_next_cpu
genhd: check for int overflow in disk_expand_part_tbl()
blk-mq: add blk_mq_free_hctx_request()
blk-mq: export blk_mq_free_request()
blk-mq: use get_cpu/put_cpu instead of preempt_disable/preempt_enable
...
This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come
from as long as the platform firmware (either DT or ACPI) makes
them available. It covers both devices and "bare" device node
objects without struct device representation as that turns out to
be necessary in some cases. This has been in the works for quite
a few months (and development cycles) and has been approved by
all of the relevant maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO information
in their ACPI tables, but don't assign names to GPIO lines (in which
case the driver needs to do that on the basis of what it knows about
the device in question). That also has been approved by the GPIO
core maintainers and the rfkill driver is now going to use it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by
the processor in which case it will be enabled by default. However,
it can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller).
The support added this time is sufficient to make the ACPI battery
driver work on Asus T100A, but it is general enough to be able to
cover some other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver
for Intel platforms should be able to handle power management of
the DMA engine correctly, the cpufreq-dt driver should interact
with the thermal subsystem in a better way and the ACPI backlight
driver should handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions
in the ACPICA's interrupt handling code which might lead to some
random and strange looking failures on some systems.
In the cleanups department the most visible part is the series
of commits targeted at getting rid of the CONFIG_PM_RUNTIME
configuration option. That was triggered by a discussion
regarding the generic power domains code during which we realized
that trying to support certain combinations of PM config options
was painful and not really worth it, because nobody would use them
in production anyway. For this reason, we decided to make
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and that lead to the
conclusion that the latter became redundant and CONFIG_PM could
be used instead of it. The material here makes that replacement
in a major part of the tree, but there will be at least one more
batch of that in the second part of the merge window.
Specifics:
- Support for retrieving device properties information from ACPI
_DSD device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that.
As stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers
are now going to use this new interface and the GPIO subsystem
is additionally modified to allow device drivers to assign names
to GPIO resources returned by ACPI _CRS objects (in case _DSD is
not present or does not provide the expected data). The changes
in this set are mostly from Mika Westerberg, Rafael J Wysocki,
Aaron Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions
used by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management
(Aaron Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects
and deferred probing support for the ACPI battery driver based
on the _DEP information to make that driver work on Asus T100A
(Lan Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling
code and in the ACPI code related to system suspend and resume
(Lv Zheng and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had
been allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in
that code with synchronize_rcu_expedited() which makes the issue
go away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly.
The problem is that the DMA engine doesn't have ACPI PM support
of its own and it simply is turned off when the last LPSS device
having ACPI PM support goes into D3cold. To work around that,
the PM domain used by the ACPI LPSS driver is redesigned so at
least one device with ACPI PM support will be on as long as the
DMA engine is in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and
Ashwin Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver
fixes and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at
probe time (Ulf Hansson).
- Preliminary support for controlling device clocks from the
generic power domains core code and modifications of the
ARM/shmobile platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power
domains core code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control
code in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and
a new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu,
James Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to
allow OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and
Markus Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=5dox
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
blk-mq users are allowed to free the memory request_queue.tag_set
points at after blk_cleanup_queue() has finished but before
blk_release_queue() has started. This can happen e.g. in the SCSI
core. The SCSI core namely embeds the tag_set structure in a SCSI
host structure. The SCSI host structure is freed by
scsi_host_dev_release(). This function is called after
blk_cleanup_queue() finished but can be called before
blk_release_queue().
This means that it is not safe to access request_queue.tag_set from
inside blk_release_queue(). Hence remove the blk_sync_queue() call
from blk_release_queue(). This call is not necessary - outstanding
requests must have finished before blk_release_queue() is
called. Additionally, move the blk_mq_free_queue() call from
blk_release_queue() to blk_cleanup_queue() to avoid that struct
request_queue.tag_set gets accessed after it has been freed.
This patch avoids that the following kernel oops can be triggered
when deleting a SCSI host for which scsi-mq was enabled:
Call Trace:
[<ffffffff8109a7c4>] lock_acquire+0xc4/0x270
[<ffffffff814ce111>] mutex_lock_nested+0x61/0x380
[<ffffffff812575f0>] blk_mq_free_queue+0x30/0x180
[<ffffffff8124d654>] blk_release_queue+0x84/0xd0
[<ffffffff8126c29b>] kobject_cleanup+0x7b/0x1a0
[<ffffffff8126c140>] kobject_put+0x30/0x70
[<ffffffff81245895>] blk_put_queue+0x15/0x20
[<ffffffff8125c409>] disk_release+0x99/0xd0
[<ffffffff8133d056>] device_release+0x36/0xb0
[<ffffffff8126c29b>] kobject_cleanup+0x7b/0x1a0
[<ffffffff8126c140>] kobject_put+0x30/0x70
[<ffffffff8125a78a>] put_disk+0x1a/0x20
[<ffffffff811d4cb5>] __blkdev_put+0x135/0x1b0
[<ffffffff811d56a0>] blkdev_put+0x50/0x160
[<ffffffff81199eb4>] kill_block_super+0x44/0x70
[<ffffffff8119a2a4>] deactivate_locked_super+0x44/0x60
[<ffffffff8119a87e>] deactivate_super+0x4e/0x70
[<ffffffff811b9833>] cleanup_mnt+0x43/0x90
[<ffffffff811b98d2>] __cleanup_mnt+0x12/0x20
[<ffffffff8107252c>] task_work_run+0xac/0xe0
[<ffffffff81002c01>] do_notify_resume+0x61/0xa0
[<ffffffff814d2c58>] int_signal+0x12/0x17
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Robert Elliott <elliott@hp.com>
Cc: Ming Lei <ming.lei@canonical.com>
Cc: Alexander Gordeev <agordeev@redhat.com>
Cc: <stable@vger.kernel.org> # v3.13+
Signed-off-by: Jens Axboe <axboe@fb.com>
After commit b2b49ccbdd (PM: Kconfig: Set PM_RUNTIME if PM_SLEEP is
selected) PM_RUNTIME is always set if PM is set, so #ifdef blocks
depending on CONFIG_PM_RUNTIME may now be changed to depend on
CONFIG_PM.
Replace CONFIG_PM_RUNTIME with CONFIG_PM in the block device core.
Reviewed-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently scsi piggy backs on the block layer to define the concept
of a tagged command. But we want to be able to have block-level host-wide
tags assigned even for untagged commands like the initial INQUIRY, so add
a new SCSI-level flag for commands that are tagged at the scsi level, so
that even commands without that set can have tags assigned to them. Note
that this alredy is the case for the blk-mq code path, and this just lets
the old path catch up with it.
We also set this flag based upon sdev->simple_tags instead of the block
queue flag, so that it is entirely independent of the block layer tagging,
and thus always correct even if a driver doesn't use block level tagging
yet.
Also remove the old blk_rq_tagged; it was only used by SCSI drivers, and
removing it forces them to look for the proper replacement.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Pull core block layer changes from Jens Axboe:
"This is the core block IO pull request for 3.18. Apart from the new
and improved flush machinery for blk-mq, this is all mostly bug fixes
and cleanups.
- blk-mq timeout updates and fixes from Christoph.
- Removal of REQ_END, also from Christoph. We pass it through the
->queue_rq() hook for blk-mq instead, freeing up one of the request
bits. The space was overly tight on 32-bit, so Martin also killed
REQ_KERNEL since it's no longer used.
- blk integrity updates and fixes from Martin and Gu Zheng.
- Update to the flush machinery for blk-mq from Ming Lei. Now we
have a per hardware context flush request, which both cleans up the
code should scale better for flush intensive workloads on blk-mq.
- Improve the error printing, from Rob Elliott.
- Backing device improvements and cleanups from Tejun.
- Fixup of a misplaced rq_complete() tracepoint from Hannes.
- Make blk_get_request() return error pointers, fixing up issues
where we NULL deref when a device goes bad or missing. From Joe
Lawrence.
- Prep work for drastically reducing the memory consumption of dm
devices from Junichi Nomura. This allows creating clone bio sets
without preallocating a lot of memory.
- Fix a blk-mq hang on certain combinations of queue depths and
hardware queues from me.
- Limit memory consumption for blk-mq devices for crash dump
scenarios and drivers that use crazy high depths (certain SCSI
shared tag setups). We now just use a single queue and limited
depth for that"
* 'for-3.18/core' of git://git.kernel.dk/linux-block: (58 commits)
block: Remove REQ_KERNEL
blk-mq: allocate cpumask on the home node
bio-integrity: remove the needless fail handle of bip_slab creating
block: include func name in __get_request prints
block: make blk_update_request print prefix match ratelimited prefix
blk-merge: don't compute bi_phys_segments from bi_vcnt for cloned bio
block: fix alignment_offset math that assumes io_min is a power-of-2
blk-mq: Make bt_clear_tag() easier to read
blk-mq: fix potential hang if rolling wakeup depth is too high
block: add bioset_create_nobvec()
block: use bio_clone_fast() in blk_rq_prep_clone()
block: misplaced rq_complete tracepoint
sd: Honor block layer integrity handling flags
block: Replace strnicmp with strncasecmp
block: Add T10 Protection Information functions
block: Don't merge requests if integrity flags differ
block: Integrity checksum flag
block: Relocate bio integrity flags
block: Add a disk flag to block integrity profile
block: Add prefix to block integrity profile flags
...
In __get_request calls to printk_ratelimited, include the function name so
the callbacks suppressed message matches the messages that are printed,
and add "dev" before the device name so it matches other block layer
messages.
Signed-off-by: Robert Elliott <elliott@hp.com>
Reviewed-by: Webb Scales <webbnh@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Request cloning clones bios in the request to track the completion
of each bio.
For that purpose, we can use bio_clone_fast() instead of bio_clone()
to avoid unnecessary allocation and copy of bvecs.
This patch reduces memory footprint of request-based device-mapper
(about 1-4KB for each request) and is a preparation for further
reduction of memory usage by removing unused bvec mempool.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The rq_complete tracepoint was never issued for empty requests,
causing the resulting blktrace information to never show any
completion for those request.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch supports to run one single flush machinery for
each blk-mq dispatch queue, so that:
- current init_request and exit_request callbacks can
cover flush request too, then the buggy copying way of
initializing flush request's pdu can be fixed
- flushing performance gets improved in case of multi hw-queue
In fio sync write test over virtio-blk(4 hw queues, ioengine=sync,
iodepth=64, numjobs=4, bs=4K), it is observed that througput gets
increased a lot over my test environment:
- throughput: +70% in case of virtio-blk over null_blk
- throughput: +30% in case of virtio-blk over SSD image
The multi virtqueue feature isn't merged to QEMU yet, and patches for
the feature can be found in below tree:
git://kernel.ubuntu.com/ming/qemu.git v2.1.0-mq.4
And simply passing 'num_queues=4 vectors=5' should be enough to
enable multi queue(quad queue) feature for QEMU virtio-blk.
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch adds 'blk_mq_ctx' parameter to blk_get_flush_queue(),
so that this function can find the corresponding blk_flush_queue
bound with current mq context since the flush queue will become
per hw-queue.
For legacy queue, the parameter can be simply 'NULL'.
For multiqueue case, the parameter should be set as the context
from which the related request is originated. With this context
info, the hw queue and related flush queue can be found easily.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Now mission of the two helpers is over, and just call
blk_alloc_flush_queue() and blk_free_flush_queue() directly.
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch introduces 'struct blk_flush_queue' and puts all
flush machinery related fields into this structure, so that
- flush implementation details aren't exposed to driver
- it is easy to convert to per dispatch-queue flush machinery
This patch is basically a mechanical replacement.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
These fields are always used with the flush request, so
initialize them together.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
These two temporary functions are introduced for holding flush
initialization and de-initialization, so that we can
introduce 'flush queue' easier in the following patch. And
once 'flush queue' and its allocation/free functions are ready,
they will be removed for sake of code readability.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Ming Lei <ming.lei@canonical.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
A bit of churn on the for-linus side that would be nice to have
in the core bits for 3.18, so pull it in to catch us up and make
forward progress easier.
Signed-off-by: Jens Axboe <axboe@fb.com>
Conflicts:
block/scsi_ioctl.c
This patch fix spelling typo found in DocBook/kernel-api.xml.
It is because the file is generated from the source comments,
I have to fix the comments in source codes.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
bdev_get_queue() returns the request_queue associated with the
specified block_device. blk_get_backing_dev_info() makes use of
bdev_get_queue() to determine the associated bdi given a block_device.
All the callers of bdev_get_queue() including
blk_get_backing_dev_info() assume that bdev_get_queue() may return
NULL and implement NULL handling; however, bdev_get_queue() requires
the passed in block_device is opened and attached to its gendisk.
Because an active gendisk always has a valid request_queue associated
with it, bdev_get_queue() can never return NULL and neither can
blk_get_backing_dev_info().
Make it clear that neither of the two functions can return NULL and
remove NULL handling from all the callers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Chris Mason <clm@fb.com>
Cc: Dave Chinner <david@fromorbit.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
The blk_get_request function may fail in low-memory conditions or during
device removal (even if __GFP_WAIT is set). To distinguish between these
errors, modify the blk_get_request call stack to return the appropriate
ERR_PTR. Verify that all callers check the return status and consider
IS_ERR instead of a simple NULL pointer check.
For consistency, make a similar change to the blk_mq_alloc_request leg
of blk_get_request. It may fail if the queue is dead, or the caller was
unwilling to wait.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Jiri Kosina <jkosina@suse.cz> [for pktdvd]
Acked-by: Boaz Harrosh <bharrosh@panasas.com> [for osd]
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fixes code such as the following with scsi-mq enabled:
rq = blk_get_request(...);
blk_rq_set_block_pc(rq);
rq->cmd = my_cmd_buffer; /* separate CDB buffer */
blk_execute_rq_nowait(...);
Code like this appears in e.g. sg_start_req() in drivers/scsi/sg.c (for
large CDBs only). Without this patch, scsi_mq_prep_fn() will set
rq->cmd back to rq->__cmd, causing the wrong CDB to be sent to the device.
Signed-off-by: Tony Battersby <tonyb@cybernetics.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
blk_mq freezing is entangled with generic bypassing which bypasses
blkcg and io scheduler and lets IO requests fall through the block
layer to the drivers in FIFO order. This allows forward progress on
IOs with the advanced features disabled so that those features can be
configured or altered without worrying about stalling IO which may
lead to deadlock through memory allocation.
However, generic bypassing doesn't quite fit blk-mq. blk-mq currently
doesn't make use of blkcg or ioscheds and it maps bypssing to
freezing, which blocks request processing and drains all the in-flight
ones. This causes problems as bypassing assumes that request
processing is online. blk-mq works around this by conditionally
allowing request processing for the problem case - during queue
initialization.
Another weirdity is that except for during queue cleanup, bypassing
started on the generic side prevents blk-mq from processing new
requests but doesn't drain the in-flight ones. This shouldn't break
anything but again highlights that something isn't quite right here.
The root cause is conflating blk-mq freezing and generic bypassing
which are two different mechanisms. The only intersecting purpose
that they serve is during queue cleanup. Let's properly separate
blk-mq freezing from generic bypassing and simply use it where
necessary.
* request_queue->mq_freeze_depth is added and
blk_mq_[un]freeze_queue() now operate on this counter instead of
->bypass_depth. The replacement for QUEUE_FLAG_BYPASS isn't added
but the counter is tested directly. This will be further updated by
later changes.
* blk_mq_drain_queue() is dropped and "__" prefix is dropped from
blk_mq_freeze_queue(). Queue cleanup path now calls
blk_mq_freeze_queue() directly.
* blk_queue_enter()'s fast path condition is simplified to simply
check @q->mq_freeze_depth. Previously, the condition was
!blk_queue_dying(q) &&
(!blk_queue_bypass(q) || !blk_queue_init_done(q))
mq_freeze_depth is incremented right after dying is set and
blk_queue_init_done() exception isn't necessary as blk-mq doesn't
start frozen, which only leaves the blk_queue_bypass() test which
can be replaced by @q->mq_freeze_depth test.
This change simplifies the code and reduces confusion in the area.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Currently, both blk_queue_bypass_start() and blk_mq_freeze_queue()
skip queue draining if bypass_depth was already above zero. The
assumption is that the one which bumped the bypass_depth should have
performed draining already; however, there's nothing which prevents a
new instance of bypassing/freezing from starting before the previous
one finishes draining. The current code may allow the later
bypassing/freezing instances to complete while there still are
in-flight requests which haven't finished draining.
Fix it by draining regardless of bypass_depth. We still skip draining
from blk_queue_bypass_start() while the queue is initializing to avoid
introducing excessive delays during boot. INIT_DONE setting is moved
above the initial blk_queue_bypass_end() so that bypassing attempts
can't slip inbetween.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Nicholas A. Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull block fixes from Jens Axboe:
"A smaller collection of fixes for the block core that would be nice to
have in -rc2. This pull request contains:
- Fixes for races in the wait/wakeup logic used in blk-mq from
Alexander. No issues have been observed, but it is definitely a
bit flakey currently. Alternatively, we may drop the cyclic
wakeups going forward, but that needs more testing.
- Some cleanups from Christoph.
- Fix for an oops in null_blk if queue_mode=1 and softirq completions
are used. From me.
- A fix for a regression caused by the chunk size setting. It
inadvertently used max_hw_sectors instead of max_sectors, which is
incorrect, and causes hangs on btrfs multi-disk setups (where hw
sectors apparently isn't set). From me.
- Removal of WQ_POWER_EFFICIENT in the kblockd creation. This was a
recent addition as well, but it actually breaks blk-mq which relies
on strict scheduling. If the workqueue power_efficient mode is
turned on, this breaks blk-mq. From Matias.
- null_blk module parameter description fix from Mike"
* 'for-linus' of git://git.kernel.dk/linux-block:
blk-mq: bitmap tag: fix races in bt_get() function
blk-mq: bitmap tag: fix race on blk_mq_bitmap_tags::wake_cnt
blk-mq: bitmap tag: fix races on shared ::wake_index fields
block: blk_max_size_offset() should check ->max_sectors
null_blk: fix softirq completions for queue_mode == 1
blk-mq: merge blk_mq_drain_queue and __blk_mq_drain_queue
blk-mq: properly drain stopped queues
block: remove WQ_POWER_EFFICIENT from kblockd
null_blk: fix name and description of 'queue_mode' module parameter
block: remove elv_abort_queue and blk_abort_flushes
Pull NVMe update from Matthew Wilcox:
"Mostly bugfixes again for the NVMe driver. I'd like to call out the
exported tracepoint in the block layer; I believe Keith has cleared
this with Jens.
We've had a few reports from people who're really pounding on NVMe
devices at scale, hence the timeout changes (and new module
parameters), hotplug cpu deadlock, tracepoints, and minor performance
tweaks"
[ Jens hadn't seen that tracepoint thing, but is ok with it - it will
end up going away when mq conversion happens ]
* git://git.infradead.org/users/willy/linux-nvme: (22 commits)
NVMe: Fix START_STOP_UNIT Scsi->NVMe translation.
NVMe: Use Log Page constants in SCSI emulation
NVMe: Define Log Page constants
NVMe: Fix hot cpu notification dead lock
NVMe: Rename io_timeout to nvme_io_timeout
NVMe: Use last bytes of f/w rev SCSI Inquiry
NVMe: Adhere to request queue block accounting enable/disable
NVMe: Fix nvme get/put queue semantics
NVMe: Delete NVME_GET_FEAT_TEMP_THRESH
NVMe: Make admin timeout a module parameter
NVMe: Make iod bio timeout a parameter
NVMe: Prevent possible NULL pointer dereference
NVMe: Fix the buffer size passed in GetLogPage(CDW10.NUMD)
NVMe: Update data structures for NVMe 1.2
NVMe: Enable BUILD_BUG_ON checks
NVMe: Update namespace and controller identify structures to the 1.1a spec
NVMe: Flush with data support
NVMe: Configure support for block flush
NVMe: Add tracepoints
NVMe: Protect against badly formatted CQEs
...
blk-mq issues async requests through kblockd. To issue a work request on
a specific CPU, kblockd_schedule_delayed_work_on is used. However, the
specific CPU choice may not be honored, if the power_efficient option
for workqueues is set. blk-mq requires that we have strict per-cpu
scheduling, so it wont work properly if kblockd is marked
POWER_EFFICIENT and power_efficient is set.
Remove the kblockd WQ_POWER_EFFICIENT flag to prevent this behavior.
This essentially reverts part of commit 695588f945, which added
the WQ_POWER_EFFICIENT marker to kblockd.
Signed-off-by: Matias Bjørling <m@bjorling.me>
Signed-off-by: Jens Axboe <axboe@fb.com>
With the optimizations around not clearing the full request at alloc
time, we are leaving some of the needed init for REQ_TYPE_BLOCK_PC
up to the user allocating the request.
Add a blk_rq_set_block_pc() that sets the command type to
REQ_TYPE_BLOCK_PC, and properly initializes the members associated
with this type of request. Update callers to use this function instead
of manipulating rq->cmd_type directly.
Includes fixes from Christoph Hellwig <hch@lst.de> for my half-assed
attempt.
Signed-off-by: Jens Axboe <axboe@fb.com>
I don't think we've ever caught any bugs with this, and there's the
list poisoning for the plug lists to catch uninitialized cases.
So remove the magic member and save 8 bytes in the struct.
Signed-off-by: Jens Axboe <axboe@fb.com>
Instead of having two almost identical copies of the same code just let
the callers pass in the reserved flag directly.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
The percpu counter is only used for blk-mq, so move
its allocation and free inside blk-mq, and don't
allocate it for legacy queue device.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
In blk_mq_make_request(), do the blk_queue_nomerges() check
outside the call to blk_attempt_plug_merge() to eliminate
function call overhead when nomerges=2 (disabled)
Signed-off-by: Robert Elliott <elliott@hp.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
For request_fn based devices, the block layer exports a 'nr_requests'
file through sysfs to allow adjusting of queue depth on the fly.
Currently this returns -EINVAL for blk-mq, since it's not wired up.
Wire this up for blk-mq, so that it now also always dynamic
adjustments of the allowed queue depth for any given block device
managed by blk-mq.
Signed-off-by: Jens Axboe <axboe@fb.com>
We first check if we have inflight IO, then retrieve that
same number again. Usually this isn't that costly since the
chance of having the data dirtied in between is small, but
there's no reason for calling part_in_flight() twice.
Signed-off-by: Jens Axboe <axboe@fb.com>
Adding tracepoints for bio_complete and block_split into nvme to help
with gathering IO info using blktrace and blkparse.
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
This allows to mirror the blk-mq code flow for more a more readable I/O
completion handler in SCSI.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
Add a blk-mq equivalent to blk_delay_queue so that the scsi layer can ask
to be kicked again after a delay.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Modified by me to kill the unnecessary preempt disable/enable
in the delayed workqueue handler.
Signed-off-by: Jens Axboe <axboe@fb.com>
This was used in the olden days, back when onions were proper
yellow. Basically it mapped to the current buffer to be
transferred. With highmem being added more than a decade ago,
most drivers map pages out of a bio, and rq->buffer isn't
pointing at anything valid.
Convert old style drivers to just use bio_data().
For the discard payload use case, just reference the page
in the bio.
Signed-off-by: Jens Axboe <axboe@fb.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJTSv89AAoJEHm+PkMAQRiGd7AIAKL45dFRhX96W53uzGlpXtv7
Ecs9CMY5mtsB/rqtV/NSQaUELlNb4Ilb4lITh7NaLWAZxDJ12GwVsIbFoaBj7Ypx
tfBNNxffGGnTTn2C1PpPQmLytLBvqXIVHMaPpDvnHYJl6g9BihshLzyMrsrizqnA
DPJ0xMdgGp6BLC4qm0ZH1mS2q+TyXLN2ZCjJ1lp6NNYwBnwOe/ABjnUa0Ztu7aii
837N8h6nEuKHTr6DgrYHEgYVc3DPHPHaly/UJ8v4U30myzRv83YkD5DsBSUjSLj8
CzxJEnECa1XljLJK7SjRHy5pSP9tcUlmjx3Fk7IpQixmT+A15cov6fQ967jNlDw=
=Hxnc
-----END PGP SIGNATURE-----
Merge tag 'v3.15-rc1' into for-3.16/core
We don't like this, but things have diverged with the blk-mq fixes
in 3.15-rc1. So merge it in.
Martin reported that his test system would not boot with
current git, it oopsed with this:
BUG: unable to handle kernel paging request at ffff88046c6c9e80
IP: [<ffffffff812971e0>] blk_queue_start_tag+0x90/0x150
PGD 1ddf067 PUD 1de2067 PMD 47fc7d067 PTE 800000046c6c9060
Oops: 0002 [#1] SMP DEBUG_PAGEALLOC
Modules linked in: sd_mod lpfc(+) scsi_transport_fc scsi_tgt oracleasm
rpcsec_gss_krb5 ipv6 igb dca i2c_algo_bit i2c_core hwmon
CPU: 3 PID: 87 Comm: kworker/u17:1 Not tainted 3.14.0+ #246
Hardware name: Supermicro X9DRX+-F/X9DRX+-F, BIOS 3.00 07/09/2013
Workqueue: events_unbound async_run_entry_fn
task: ffff8802743c2150 ti: ffff880273d02000 task.ti: ffff880273d02000
RIP: 0010:[<ffffffff812971e0>] [<ffffffff812971e0>]
blk_queue_start_tag+0x90/0x150
RSP: 0018:ffff880273d03a58 EFLAGS: 00010092
RAX: ffff88046c6c9e78 RBX: ffff880077208e78 RCX: 00000000fffc8da6
RDX: 00000000fffc186d RSI: 0000000000000009 RDI: 00000000fffc8d9d
RBP: ffff880273d03a88 R08: 0000000000000001 R09: ffff8800021c2410
R10: 0000000000000005 R11: 0000000000015b30 R12: ffff88046c5bb8a0
R13: ffff88046c5c0890 R14: 000000000000001e R15: 000000000000001e
FS: 0000000000000000(0000) GS:ffff880277b00000(0000)
knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: ffff88046c6c9e80 CR3: 00000000018f6000 CR4: 00000000000407e0
Stack:
ffff880273d03a98 ffff880474b18800 0000000000000000 ffff880474157000
ffff88046c5c0890 ffff880077208e78 ffff880273d03ae8 ffffffff813b9e62
ffff880200000010 ffff880474b18968 ffff880474b18848 ffff88046c5c0cd8
Call Trace:
[<ffffffff813b9e62>] scsi_request_fn+0xf2/0x510
[<ffffffff81293167>] __blk_run_queue+0x37/0x50
[<ffffffff8129ac43>] blk_execute_rq_nowait+0xb3/0x130
[<ffffffff8129ad24>] blk_execute_rq+0x64/0xf0
[<ffffffff8108d2b0>] ? bit_waitqueue+0xd0/0xd0
[<ffffffff813bba35>] scsi_execute+0xe5/0x180
[<ffffffff813bbe4a>] scsi_execute_req_flags+0x9a/0x110
[<ffffffffa01b1304>] sd_spinup_disk+0x94/0x460 [sd_mod]
[<ffffffff81160000>] ? __unmap_hugepage_range+0x200/0x2f0
[<ffffffffa01b2b9a>] sd_revalidate_disk+0xaa/0x3f0 [sd_mod]
[<ffffffffa01b2fb8>] sd_probe_async+0xd8/0x200 [sd_mod]
[<ffffffff8107703f>] async_run_entry_fn+0x3f/0x140
[<ffffffff8106a1c5>] process_one_work+0x175/0x410
[<ffffffff8106b373>] worker_thread+0x123/0x400
[<ffffffff8106b250>] ? manage_workers+0x160/0x160
[<ffffffff8107104e>] kthread+0xce/0xf0
[<ffffffff81070f80>] ? kthread_freezable_should_stop+0x70/0x70
[<ffffffff815f0bac>] ret_from_fork+0x7c/0xb0
[<ffffffff81070f80>] ? kthread_freezable_should_stop+0x70/0x70
Code: 48 0f ab 11 72 db 48 81 4b 40 00 00 10 00 89 83 08 01 00 00 48 89
df 49 8b 04 24 48 89 1c d0 e8 f7 a8 ff ff 49 8b 85 28 05 00 00 <48> 89
58 08 48 89 03 49 8d 85 28 05 00 00 48 89 43 08 49 89 9d
RIP [<ffffffff812971e0>] blk_queue_start_tag+0x90/0x150
RSP <ffff880273d03a58>
CR2: ffff88046c6c9e80
Martin bisected and found this to be the problem patch;
commit 6d113398dc
Author: Jan Kara <jack@suse.cz>
Date: Mon Feb 24 16:39:54 2014 +0100
block: Stop abusing rq->csd.list in blk-softirq
and the problem was immediately apparent. The patch states that
it is safe to reuse queuelist at completion time, since it is
no longer used. However, that is not true if a device is using
block enabled tagging. If that is the case, then the queuelist
is reused to keep track of busy tags. If a device also ended
up using softirq completions, we'd reuse ->queuelist for the
IPI handling while block tagging was still using it. Boom.
Fix this by adding a new ipi_list list head, and share the
memory used with the request hash table. The hash table is
never used after the request is moved to the dispatch list,
which happens long before any potential completion of the
request. Add a new request bit for this, so we don't have
cases that check rq->hash while it could potentially have
been reused for the IPI completion.
Reported-by: Martin K. Petersen <martin.petersen@oracle.com>
Tested-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
Same function as kblockd_schedule_delayed_work(), but allow the
caller to pass in a CPU that the work should be executed on. This
just directly extends and maps into the workqueue API, and will
be used to make the blk-mq mappings more strict.
Signed-off-by: Jens Axboe <axboe@fb.com>
Pull core block layer updates from Jens Axboe:
"This is the pull request for the core block IO bits for the 3.15
kernel. It's a smaller round this time, it contains:
- Various little blk-mq fixes and additions from Christoph and
myself.
- Cleanup of the IPI usage from the block layer, and associated
helper code. From Frederic Weisbecker and Jan Kara.
- Duplicate code cleanup in bio-integrity from Gu Zheng. This will
give you a merge conflict, but that should be easy to resolve.
- blk-mq notify spinlock fix for RT from Mike Galbraith.
- A blktrace partial accounting bug fix from Roman Pen.
- Missing REQ_SYNC detection fix for blk-mq from Shaohua Li"
* 'for-3.15/core' of git://git.kernel.dk/linux-block: (25 commits)
blk-mq: add REQ_SYNC early
rt,blk,mq: Make blk_mq_cpu_notify_lock a raw spinlock
blk-mq: support partial I/O completions
blk-mq: merge blk_mq_insert_request and blk_mq_run_request
blk-mq: remove blk_mq_alloc_rq
blk-mq: don't dump CPU -> hw queue map on driver load
blk-mq: fix wrong usage of hctx->state vs hctx->flags
blk-mq: allow blk_mq_init_commands() to return failure
block: remove old blk_iopoll_enabled variable
blktrace: fix accounting of partially completed requests
smp: Rename __smp_call_function_single() to smp_call_function_single_async()
smp: Remove wait argument from __smp_call_function_single()
watchdog: Simplify a little the IPI call
smp: Move __smp_call_function_single() below its safe version
smp: Consolidate the various smp_call_function_single() declensions
smp: Teach __smp_call_function_single() to check for offline cpus
smp: Remove unused list_head from csd
smp: Iterate functions through llist_for_each_entry_safe()
block: Stop abusing rq->csd.list in blk-softirq
block: Remove useless IPI struct initialization
...
Commit 7982e90c3a ("block: fix q->flush_rq NULL pointer crash on
dm-mpath flush") moved an allocation to blk_init_allocated_queue(), but
neglected to free that allocation on the error paths that follow.
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
trace_block_rq_complete does not take into account that request can
be partially completed, so we can get the following incorrect output
of blkparser:
C R 232 + 240 [0]
C R 240 + 232 [0]
C R 248 + 224 [0]
C R 256 + 216 [0]
but should be:
C R 232 + 8 [0]
C R 240 + 8 [0]
C R 248 + 8 [0]
C R 256 + 8 [0]
Also, the whole output summary statistics of completed requests and
final throughput will be incorrect.
This patch takes into account real completion size of the request and
fixes wrong completion accounting.
Signed-off-by: Roman Pen <r.peniaev@gmail.com>
CC: Steven Rostedt <rostedt@goodmis.org>
CC: Frederic Weisbecker <fweisbec@gmail.com>
CC: Ingo Molnar <mingo@redhat.com>
CC: linux-kernel@vger.kernel.org
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch fix spelling typo in Documentation/DocBook.
It is because .html and .xml files are generated by make htmldocs,
I have to fix a typo within the source files.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Witch to using a preallocated flush_rq for blk-mq similar to what's done
with the old request path. This allows us to set up the request properly
with a tag from the actually allowed range and ->rq_disk as needed by
some drivers. To make life easier we also switch to dynamic allocation
of ->flush_rq for the old path.
This effectively reverts most of
"blk-mq: fix for flush deadlock"
and
"blk-mq: Don't reserve a tag for flush request"
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
__blk_put_request needs to call into the blk-mq code just like
blk_put_request. As we don't have the queue lock in this case both
end up calling the same function.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
This patch moves synchronization on mq->delay_work
from blk_mq_free_queue() to blk_sync_queue(), so that
blk_sync_queue can work on mq.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
blk_mq_drain_queue() is introduced so that we can drain
mq queue inside blk_cleanup_queue().
Also don't accept new requests any more if queue is marked
as dying.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
More prep work for immutable biovecs - with immutable bvecs drivers
won't be able to use the biovec directly, they'll need to use helpers
that take into account bio->bi_iter.bi_bvec_done.
This updates callers for the new usage without changing the
implementation yet.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Paul Clements <Paul.Clements@steeleye.com>
Cc: Jim Paris <jim@jtan.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@inktank.com>
Cc: ceph-devel@vger.kernel.org
Cc: Joshua Morris <josh.h.morris@us.ibm.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: Nagalakshmi Nandigama <Nagalakshmi.Nandigama@lsi.com>
Cc: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Cc: support@lsi.com
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Guo Chao <yan@linux.vnet.ibm.com>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: Quoc-Son Anh <quoc-sonx.anh@intel.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jerome Marchand <jmarchan@redhat.com>
Cc: Seth Jennings <sjenning@linux.vnet.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: "Darrick J. Wong" <darrick.wong@oracle.com>
Cc: Chris Metcalf <cmetcalf@tilera.com>
Cc: Jan Kara <jack@suse.cz>
Cc: linux-m68k@lists.linux-m68k.org
Cc: linuxppc-dev@lists.ozlabs.org
Cc: drbd-user@lists.linbit.com
Cc: nbd-general@lists.sourceforge.net
Cc: cbe-oss-dev@lists.ozlabs.org
Cc: xen-devel@lists.xensource.com
Cc: virtualization@lists.linux-foundation.org
Cc: linux-raid@vger.kernel.org
Cc: linux-s390@vger.kernel.org
Cc: DL-MPTFusionLinux@lsi.com
Cc: linux-scsi@vger.kernel.org
Cc: devel@driverdev.osuosl.org
Cc: linux-fsdevel@vger.kernel.org
Cc: cluster-devel@redhat.com
Cc: linux-mm@kvack.org
Acked-by: Geoff Levand <geoff@infradead.org>
This patch enables the sysfs to control I/O request merge
functionality in the plug list. While this control has been
implemented for the request queue, it was dismissed in the plug list.
Therefore, block layer merges requests together (or attempt to merge)
even if the merge capability was disable using sysfs nomerge parameter
value 2.
This limitation is directly affects functionality of io_submit()
system call. The system call enables user to submit a bunch of IO
requests from user space using struct iocb **ios input argument.
However, the unconditioned merging functionality in the plug list
potentially merges these requests together down the road. Therefore,
there is no way to distinguish between an application sending bunch of
sequential IOs and an application sending one big IO. Ultimately, all
requests generated by the former app merge within the plug list
together and looks similar to the second app.
While the merging functionality is a desirable feature to improve the
performance of IO subsystem for some applications, it is not useful
for other application like ours at all.
Signed-off-by: Alireza Haghdoost <alireza@cs.umn.edu>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Coding style modified.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The soft lockup below happens at the boot time of the system using dm
multipath and the udev rules to switch scheduler.
[ 356.127001] BUG: soft lockup - CPU#3 stuck for 22s! [sh:483]
[ 356.127001] RIP: 0010:[<ffffffff81072a7d>] [<ffffffff81072a7d>] lock_timer_base.isra.35+0x1d/0x50
...
[ 356.127001] Call Trace:
[ 356.127001] [<ffffffff81073810>] try_to_del_timer_sync+0x20/0x70
[ 356.127001] [<ffffffff8118b08a>] ? kmem_cache_alloc_node_trace+0x20a/0x230
[ 356.127001] [<ffffffff810738b2>] del_timer_sync+0x52/0x60
[ 356.127001] [<ffffffff812ece22>] cfq_exit_queue+0x32/0xf0
[ 356.127001] [<ffffffff812c98df>] elevator_exit+0x2f/0x50
[ 356.127001] [<ffffffff812c9f21>] elevator_change+0xf1/0x1c0
[ 356.127001] [<ffffffff812caa50>] elv_iosched_store+0x20/0x50
[ 356.127001] [<ffffffff812d1d09>] queue_attr_store+0x59/0xb0
[ 356.127001] [<ffffffff812143f6>] sysfs_write_file+0xc6/0x140
[ 356.127001] [<ffffffff811a326d>] vfs_write+0xbd/0x1e0
[ 356.127001] [<ffffffff811a3ca9>] SyS_write+0x49/0xa0
[ 356.127001] [<ffffffff8164e899>] system_call_fastpath+0x16/0x1b
This is caused by a race between md device initialization by multipathd and
shell script to switch the scheduler using sysfs.
- multipathd:
SyS_ioctl -> do_vfs_ioctl -> dm_ctl_ioctl -> ctl_ioctl -> table_load
-> dm_setup_md_queue -> blk_init_allocated_queue -> elevator_init
q->elevator = elevator_alloc(q, e); // not yet initialized
- sh -c 'echo deadline > /sys/$DEVPATH/queue/scheduler':
elevator_switch (in the call trace above)
struct elevator_queue *old = q->elevator;
q->elevator = elevator_alloc(q, new_e);
elevator_exit(old); // lockup! (*)
- multipathd: (cont.)
err = e->ops.elevator_init_fn(q); // init fails; q->elevator is modified
(*) When del_timer_sync() is called, lock_timer_base() will loop infinitely
while timer->base == NULL. In this case, as timer will never initialized,
it results in lockup.
This patch introduces acquisition of q->sysfs_lock around elevator_init()
into blk_init_allocated_queue(), to provide mutual exclusion between
initialization of the q->scheduler and switching of the scheduler.
This should fix this bugzilla:
https://bugzilla.redhat.com/show_bug.cgi?id=902012
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@hds.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
crocode i2c_i801 i2c_core iTCO_wdt iTCO_vendor_support shpchp ioatdma dca be2net sg ses enclosure ext4 mbcache jbd2 sd_mod crc_t10dif ahci megaraid_sas(U) dm_mirror dm_region_hash dm_log dm_mod [last unloaded: scsi_wait_scan]
Pid: 491, comm: scsi_eh_0 Tainted: G W ---------------- 2.6.32-220.13.1.el6.x86_64 #1 IBM -[8722PAX]-/00D1461
RIP: 0010:[<ffffffff8124e424>] [<ffffffff8124e424>] blk_requeue_request+0x94/0xa0
RSP: 0018:ffff881057eefd60 EFLAGS: 00010012
RAX: ffff881d99e3e8a8 RBX: ffff881d99e3e780 RCX: ffff881d99e3e8a8
RDX: ffff881d99e3e8a8 RSI: ffff881d99e3e780 RDI: ffff881d99e3e780
RBP: ffff881057eefd80 R08: ffff881057eefe90 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000000 R12: ffff881057f92338
R13: 0000000000000000 R14: ffff881057f92338 R15: ffff883058188000
FS: 0000000000000000(0000) GS:ffff880040200000(0000) knlGS:0000000000000000
CS: 0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 00000000006d3ec0 CR3: 000000302cd7d000 CR4: 00000000000406b0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process scsi_eh_0 (pid: 491, threadinfo ffff881057eee000, task ffff881057e29540)
Stack:
0000000000001057 0000000000000286 ffff8810275efdc0 ffff881057f16000
<0> ffff881057eefdd0 ffffffff81362323 ffff881057eefe20 ffffffff8135f393
<0> ffff881057e29af8 ffff8810275efdc0 ffff881057eefe78 ffff881057eefe90
Call Trace:
[<ffffffff81362323>] __scsi_queue_insert+0xa3/0x150
[<ffffffff8135f393>] ? scsi_eh_ready_devs+0x5e3/0x850
[<ffffffff81362a23>] scsi_queue_insert+0x13/0x20
[<ffffffff8135e4d4>] scsi_eh_flush_done_q+0x104/0x160
[<ffffffff8135fb6b>] scsi_error_handler+0x35b/0x660
[<ffffffff8135f810>] ? scsi_error_handler+0x0/0x660
[<ffffffff810908c6>] kthread+0x96/0xa0
[<ffffffff8100c14a>] child_rip+0xa/0x20
[<ffffffff81090830>] ? kthread+0x0/0xa0
[<ffffffff8100c140>] ? child_rip+0x0/0x20
Code: 00 00 eb d1 4c 8b 2d 3c 8f 97 00 4d 85 ed 74 bf 49 8b 45 00 49 83 c5 08 48 89 de 4c 89 e7 ff d0 49 8b 45 00 48 85 c0 75 eb eb a4 <0f> 0b eb fe 0f 1f 84 00 00 00 00 00 55 48 89 e5 0f 1f 44 00 00
RIP [<ffffffff8124e424>] blk_requeue_request+0x94/0xa0
RSP <ffff881057eefd60>
The RIP is this line:
BUG_ON(blk_queued_rq(rq));
After digging through the code, I think there may be a race between the
request completion and the timer handler running.
A timer is started for each request put on the device's queue (see
blk_start_request->blk_add_timer). If the request does not complete
before the timer expires, the timer handler (blk_rq_timed_out_timer)
will mark the request complete atomically:
static inline int blk_mark_rq_complete(struct request *rq)
{
return test_and_set_bit(REQ_ATOM_COMPLETE, &rq->atomic_flags);
}
and then call blk_rq_timed_out. The latter function will call
scsi_times_out, which will return one of BLK_EH_HANDLED,
BLK_EH_RESET_TIMER or BLK_EH_NOT_HANDLED. If BLK_EH_RESET_TIMER is
returned, blk_clear_rq_complete is called, and blk_add_timer is again
called to simply wait longer for the request to complete.
Now, if the request happens to complete while this is going on, what
happens? Given that we know the completion handler will bail if it
finds the REQ_ATOM_COMPLETE bit set, we need to focus on the completion
handler running after that bit is cleared. So, from the above
paragraph, after the call to blk_clear_rq_complete. If the completion
sets REQ_ATOM_COMPLETE before the BUG_ON in blk_add_timer, we go boom
there (I haven't seen this in the cores). Next, if we get the
completion before the call to list_add_tail, then the timer will
eventually fire for an old req, which may either be freed or reallocated
(there is evidence that this might be the case). Finally, if the
completion comes in *after* the addition to the timeout list, I think
it's harmless. The request will be removed from the timeout list,
req_atom_complete will be set, and all will be well.
This will only actually explain the coredumps *IF* the request
structure was freed, reallocated *and* queued before the error handler
thread had a chance to process it. That is possible, but it may make
sense to keep digging for another race. I think that if this is what
was happening, we would see other instances of this problem showing up
as null pointer or garbage pointer dereferences, for example when the
request structure was not re-used. It looks like we actually do run
into that situation in other reports.
This patch moves the BUG_ON(test_bit(REQ_ATOM_COMPLETE,
&req->atomic_flags)); from blk_add_timer to the only caller that could
trip over it (blk_start_request). It then inverts the calls to
blk_clear_rq_complete and blk_add_timer in blk_rq_timed_out to address
the race. I've boot tested this patch, but nothing more.
Signed-off-by: Jeff Moyer <jmoyer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Cc: stable@kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We switched to plug mq_list for mq, but some code are still using old list.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
The flush state machine takes in a struct request, which then is
submitted multiple times to the underling driver. The old block code
requeses the same request for each of those, so it does not have an
issue with tapping into the request pool. The new one on the other hand
allocates a new request for each of the actualy steps of the flush
sequence. If have already allocated all of the tags for IO, we will
fail allocating the flush request.
Set aside a reserved request just for flushes.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Linux currently has two models for block devices:
- The classic request_fn based approach, where drivers use struct
request units for IO. The block layer provides various helper
functionalities to let drivers share code, things like tag
management, timeout handling, queueing, etc.
- The "stacked" approach, where a driver squeezes in between the
block layer and IO submitter. Since this bypasses the IO stack,
driver generally have to manage everything themselves.
With drivers being written for new high IOPS devices, the classic
request_fn based driver doesn't work well enough. The design dates
back to when both SMP and high IOPS was rare. It has problems with
scaling to bigger machines, and runs into scaling issues even on
smaller machines when you have IOPS in the hundreds of thousands
per device.
The stacked approach is then most often selected as the model
for the driver. But this means that everybody has to re-invent
everything, and along with that we get all the problems again
that the shared approach solved.
This commit introduces blk-mq, block multi queue support. The
design is centered around per-cpu queues for queueing IO, which
then funnel down into x number of hardware submission queues.
We might have a 1:1 mapping between the two, or it might be
an N:M mapping. That all depends on what the hardware supports.
blk-mq provides various helper functions, which include:
- Scalable support for request tagging. Most devices need to
be able to uniquely identify a request both in the driver and
to the hardware. The tagging uses per-cpu caches for freed
tags, to enable cache hot reuse.
- Timeout handling without tracking request on a per-device
basis. Basically the driver should be able to get a notification,
if a request happens to fail.
- Optional support for non 1:1 mappings between issue and
submission queues. blk-mq can redirect IO completions to the
desired location.
- Support for per-request payloads. Drivers almost always need
to associate a request structure with some driver private
command structure. Drivers can tell blk-mq this at init time,
and then any request handed to the driver will have the
required size of memory associated with it.
- Support for merging of IO, and plugging. The stacked model
gets neither of these. Even for high IOPS devices, merging
sequential IO reduces per-command overhead and thus
increases bandwidth.
For now, this is provided as a potential 3rd queueing model, with
the hope being that, as it matures, it can replace both the classic
and stacked model. That would get us back to having just 1 real
model for block devices, leaving the stacked approach to dm/md
devices (as it was originally intended).
Contributions in this patch from the following people:
Shaohua Li <shli@fusionio.com>
Alexander Gordeev <agordeev@redhat.com>
Christoph Hellwig <hch@infradead.org>
Mike Christie <michaelc@cs.wisc.edu>
Matias Bjorling <m@bjorling.me>
Jeff Moyer <jmoyer@redhat.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This reference count has been around since before git history, but the only
place where it's used is in blk_execute_rq, and ther it is entirely useless
as it is incremented before submitting the request and decremented in the
end_io handler before waking up the submitter thread.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We have officially run out of flags in a 32-bit space. Extend it
to 64-bit even on 32-bit archs.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block IO fixes from Jens Axboe:
"After merge window, no new stuff this time only a collection of neatly
confined and simple fixes"
* 'for-3.12/core' of git://git.kernel.dk/linux-block:
cfq: explicitly use 64bit divide operation for 64bit arguments
block: Add nr_bios to block_rq_remap tracepoint
If the queue is dying then we only call the rq->end_io callout. This leaves bios setup on the request, because the caller assumes when the blk_execute_rq_nowait/blk_execute_rq call has completed that the rq->bios have been cleaned up.
bio-integrity: Fix use of bs->bio_integrity_pool after free
blkcg: relocate root_blkg setting and clearing
block: Convert kmalloc_node(...GFP_ZERO...) to kzalloc_node(...)
block: trace all devices plug operation
In func blk_queue_bio, if list of plug is empty,it will call
blk_trace_plug.
If process deal with a single device,it't ok.But if process deal with
multi devices,it only trace the first device.
Using request_count to judge, it can soleve this problem.
In addition, i modify the comment.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When a medium error is detected the SCSI stack should return
ENODATA to the upper layers.
[jejb: fix whitespace error]
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the thin provisioning hard threshold is reached we
should return ENOSPC to inform upper layers about this fact.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull s390 updates from Martin Schwidefsky:
"This is the bulk of the s390 patches for the 3.11 merge window.
Notable enhancements are: the block timeout patches for dasd from
Hannes, and more work on the PCI support front. In addition some
cleanup and the usual bug fixing."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (42 commits)
s390/dasd: Fail all requests when DASD_FLAG_ABORTIO is set
s390/dasd: Add 'timeout' attribute
block: check for timeout function in blk_rq_timed_out()
block/dasd: detailed I/O errors
s390/dasd: Reduce amount of messages for specific errors
s390/dasd: Implement block timeout handling
s390/dasd: process all requests in the device tasklet
s390/dasd: make number of retries configurable
s390/dasd: Clarify comment
s390/hwsampler: Updated misleading member names in hws_data_entry
s390/appldata_net_sum: do not use static data
s390/appldata_mem: do not use static data
s390/vmwatchdog: do not use static data
s390/airq: simplify adapter interrupt code
s390/pci: remove per device debug attribute
s390/dma: remove gratuitous brackets
s390/facility: decompose test_facility()
s390/sclp: remove duplicated include from sclp_ctl.c
s390/irq: store interrupt information in pt_regs
s390/drivers: Cocci spatch "ptr_ret.spatch"
...
Pull workqueue changes from Tejun Heo:
"Surprisingly, Lai and I didn't break too many things implementing
custom pools and stuff last time around and there aren't any follow-up
changes necessary at this point.
The only change in this pull request is Viresh's patches to make some
per-cpu workqueues to behave as unbound workqueues dependent on a boot
param whose default can be configured via a config option. This leads
to higher processing overhead / lower bandwidth as more work items are
bounced across CPUs; however, it can lead to noticeable powersave in
certain configurations - ~10% w/ idlish constant workload on a
big.LITTLE configuration according to Viresh.
This is because per-cpu workqueues interfere with how the scheduler
perceives whether or not each CPU is idle by forcing pinned tasks on
them, which makes the scheduler's power-aware scheduling decisions
less effective.
Its effectiveness is likely less pronounced on homogenous
configurations and this type of optimization can probably be made
automatic; however, the changes are pretty minimal and the affected
workqueues are clearly marked, so it's an easy gain for some
configurations for the time being with pretty unintrusive changes."
* 'for-3.11' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
fbcon: queue work on power efficient wq
block: queue work on power efficient wq
PHYLIB: queue work on system_power_efficient_wq
workqueue: Add system wide power_efficient workqueues
workqueues: Introduce new flag WQ_POWER_EFFICIENT for power oriented workqueues
The DASD driver is using FASTFAIL as an equivalent to the
transport errors in SCSI. And the 'steal lock' function maps
roughly to a reservation error. So we should be returning the
appropriate error codes when completing a request.
Acked-by: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Stefan Weinhuber <wein@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In blk_post_runtime_resume, an autosuspend request will be initiated for
the device. Since we are holding the queue lock, we can't sleep and thus
we should use the async version to initiate an autosuspend, i.e.
pm_request_suspend instead of pm_runtime_suspend, which might sleep.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Block layer uses workqueues for multiple purposes. There is no real dependency
of scheduling these on the cpu which scheduled them.
On a idle system, it is observed that and idle cpu wakes up many times just to
service this work. It would be better if we can schedule it on a cpu which the
scheduler believes to be the most appropriate one.
This patch replaces normal workqueues with power efficient versions.
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Tejun Heo <tj@kernel.org>
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
This reverts commit 3a366e614d.
Wanlong Gao reports that it causes a kernel panic on his machine several
minutes after boot. Reverting it removes the panic.
Jens says:
"It's not quite clear why that is yet, so I think we should just revert
the commit for 3.9 final (which I'm assuming is pretty close).
The wifi is crap at the LSF hotel, so sending this email instead of
queueing up a revert and pull request."
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Requested-by: Jens Axboe <axboe@kernel.dk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Just a little convenience macro - main reason to add it now is preparing
for immutable bio vecs, it'll reduce the size of the patch that puts
bi_sector/bi_size/bi_idx into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Lars Ellenberg <drbd-dev@lists.linbit.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux-s390@vger.kernel.org
CC: Chris Mason <chris.mason@fusionio.com>
CC: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Converts it to use bio_advance(), simplifying it quite a bit in the
process.
Note that req_bio_endio() now always calls bio_advance() - which means
it always loops over the biovec, not just on partial completions. Don't
expect it to affect performance, but worth noting.
Tested it by forcing partial updates, and dumping before and after on
various bio/bvec fields when doing a partial update.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
When a request is added:
If device is suspended or is suspending and the request is not a
PM request, resume the device.
When the last request finishes:
Call pm_runtime_mark_last_busy().
When pick a request:
If device is resuming/suspending, then only PM request is allowed
to go.
The idea and API is designed by Alan Stern and described here:
http://marc.info/?l=linux-scsi&m=133727953625963&w=2
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add runtime pm helper functions:
void blk_pm_runtime_init(struct request_queue *q, struct device *dev)
- Initialization function for drivers to call.
int blk_pre_runtime_suspend(struct request_queue *q)
- If any requests are in the queue, mark last busy and return -EBUSY.
Otherwise set q->rpm_status to RPM_SUSPENDING and return 0.
void blk_post_runtime_suspend(struct request_queue *q, int err)
- If the suspend succeeded then set q->rpm_status to RPM_SUSPENDED.
Otherwise set it to RPM_ACTIVE and mark last busy.
void blk_pre_runtime_resume(struct request_queue *q)
- Set q->rpm_status to RPM_RESUMING.
void blk_post_runtime_resume(struct request_queue *q, int err)
- If the resume succeeded then set q->rpm_status to RPM_ACTIVE
and call __blk_run_queue, then mark last busy and autosuspend.
Otherwise set q->rpm_status to RPM_SUSPENDED.
The idea and API is designed by Alan Stern and described here:
http://marc.info/?l=linux-scsi&m=133727953625963&w=2
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Pull block IO core bits from Jens Axboe:
"Below are the core block IO bits for 3.9. It was delayed a few days
since my workstation kept crashing every 2-8h after pulling it into
current -git, but turns out it is a bug in the new pstate code (divide
by zero, will report separately). In any case, it contains:
- The big cfq/blkcg update from Tejun and and Vivek.
- Additional block and writeback tracepoints from Tejun.
- Improvement of the should sort (based on queues) logic in the plug
flushing.
- _io() variants of the wait_for_completion() interface, using
io_schedule() instead of schedule() to contribute to io wait
properly.
- Various little fixes.
You'll get two trivial merge conflicts, which should be easy enough to
fix up"
Fix up the trivial conflicts due to hlist traversal cleanups (commit
b67bfe0d42ca: "hlist: drop the node parameter from iterators").
* 'for-3.9/core' of git://git.kernel.dk/linux-block: (39 commits)
block: remove redundant check to bd_openers()
block: use i_size_write() in bd_set_size()
cfq: fix lock imbalance with failed allocations
drivers/block/swim3.c: fix null pointer dereference
block: don't select PERCPU_RWSEM
block: account iowait time when waiting for completion of IO request
sched: add wait_for_completion_io[_timeout]
writeback: add more tracepoints
block: add block_{touch|dirty}_buffer tracepoint
buffer: make touch_buffer() an exported function
block: add @req to bio_{front|back}_merge tracepoints
block: add missing block_bio_complete() tracepoint
block: Remove should_sort judgement when flush blk_plug
block,elevator: use new hashtable implementation
cfq-iosched: add hierarchical cfq_group statistics
cfq-iosched: collect stats from dead cfqgs
cfq-iosched: separate out cfqg_stats_reset() from cfq_pd_reset_stats()
blkcg: make blkcg_print_blkgs() grab q locks instead of blkcg lock
block: RCU free request_queue
blkcg: implement blkg_[rw]stat_recursive_sum() and blkg_[rw]stat_merge()
...
This provides a band-aid to provide stable page writes on jbd without
needing to backport the fixed locking and page writeback bit handling
schemes of jbd2. The band-aid works by using bounce buffers to snapshot
page contents instead of waiting.
For those wondering about the ext3 bandage -- fixing the jbd locking
(which was done as part of ext4dev years ago) is a lot of surgery, and
setting PG_writeback on data pages when we actually hold the page lock
dropped ext3 performance by nearly an order of magnitude. If we're
going to migrate iscsi and raid to use stable page writes, the
complaints about high latency will likely return. We might as well
centralize their page snapshotting thing to one place.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Tested-by: Andy Lutomirski <luto@amacapital.net>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Artem Bityutskiy <dedekind1@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Ron Minnich <rminnich@sandia.gov>
Cc: Latchesar Ionkov <lucho@ionkov.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
bio_{front|back}_merge tracepoints report a bio merging into an
existing request but didn't specify which request the bio is being
merged into. Add @req to it. This makes it impossible to share the
event template with block_bio_queue - split it out.
@req isn't used or exported to userland at this point and there is no
userland visible behavior change. Later changes will make use of the
extra parameter.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
bio completion didn't kick block_bio_complete TP. Only dm was
explicitly triggering the TP on IO completion. This makes
block_bio_complete TP useless for tracers which want to know about
bios, and all other bio based drivers skip generating blktrace
completion events.
This patch makes all bio completions via bio_endio() generate
block_bio_complete TP.
* Explicit trace_block_bio_complete() invocation removed from dm and
the trace point is unexported.
* @rq dropped from trace_block_bio_complete(). bios may fly around
w/o queue associated. Verifying and accessing the assocaited queue
belongs to TP probes.
* blktrace now gets both request and bio completions. Make it ignore
bio completions if request completion path is happening.
This makes all bio based drivers generate blktrace completion events
properly and makes the block_bio_complete TP actually useful.
v2: With this change, block_bio_complete TP could be invoked on sg
commands which have bio's with %NULL bi_bdev. Update TP
assignment code to check whether bio->bi_bdev is %NULL before
dereferencing.
Signed-off-by: Tejun Heo <tj@kernel.org>
Original-patch-by: Namhyung Kim <namhyung@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Mike Christie