Only the option driver implements the send_setup callback; it uses the
SET_CONTROL_LINE_STATE request in CDC ACM to generate DTR/RTS signals
on the port. This is not driver-specific though and is needed by other
drivers, so move the function to the usb_wwan driver (with formatting
tweaks), and replace the callback pointer with a flag that enables the
request.
Suggested-by: Bjørn Mork <bjorn@mork.no>
Suggested-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use tty-port initialised flag rather than private flag to determine when
port is closing down.
Since the tty-port flag is set prior to dropping DTR/RTS (when HUPCL is
set) this avoid submitting the read urbs when resuming the interface in
dtr_rts() only to immediately kill them again in shutdown().
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usb_wwan_send_setup() function has never existed.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver does not implement set_termios so the operation can be left
unset (tty will do the tty_termios_copy_hw for us).
Note that the send_setup call is bogus as it really only sets DTR/RTS
to their current values.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Make sure that needs_remote_wake up is always set when there are open
ports.
Currently close() would unconditionally set needs_remote_wakeup to 0
even though there might still be open ports. This could lead to blocked
input and possibly dropped data on devices that do not support remote
wakeup (and which must therefore not be runtime suspended while open).
Add an open_ports counter (protected by the susp_lock) and only clear
needs_remote_wakeup when the last port is closed.
Note that there are currently no multi-port drivers using the usb_wwan
implementation.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix port-data memory leak in usb-serial probe error path by moving port
data allocation to port_probe.
Since commit a1028f0abf ("usb: usb_wwan: replace release and disconnect
with a port_remove hook") port data is deallocated in port_remove. This
leaves a possibility for memory leaks if usb-serial probe fails after
attach but before the port in question has been successfully registered.
Note that this patch also fixes two additional memory leaks in the error
path of attach should port initialisation fail for any port as the urbs
were never freed and neither was the data of any of the successfully
initialised ports.
Compile-only tested.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We don't use it so we can trim it from here as we try and stamp the file
object dependencies out of the serial code.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Doing tiocmget was such fun we should do tiocmset as well for the same
reasons
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't actually need this and it causes problems for internal use of
this functionality. Currently there is a single use of the FILE * pointer.
That is the serial core which uses it to check tty_hung_up_p. However if
that is true then IO_ERROR is also already set so the check may be removed.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some devices (ex ZTE 2726) simply don't respond at all when data is sent
to some of their USB interfaces. The data gets stuck in the TTYs queue
and sits there until close(2), which them blocks because closing_wait
defaults to 30 seconds (even though the fd is O_NONBLOCK). This is
rarely desired. Implement the standard mechanism to adjust closing_wait
and let applications handle it how they want to.
Signed-off-by: Dan Williams <dcbw@redhat.com>
The generic USB serial code is ill-suited for high-speed USB wwan devices,
resulting in the option driver. However, other non-option devices may also
gain similar benefits from not using the generic code. Factorise out the
non-option specific code from the option driver and make it available to
other users.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
David Ward