When support for the A31/A31s CCU was first added, the clock ops for
the CLK_OUT_* clocks was set to the wrong type. The clocks are MP-type,
but the ops was set for div (M) clocks. This went unnoticed until now.
This was because while they are different clocks, their data structures
aligned in a way that ccu_div_ops would access the second ccu_div_internal
and ccu_mux_internal structures, which were valid, if not incorrect.
Furthermore, the use of these CLK_OUT_* was for feeding a precise 32.768
kHz clock signal to the WiFi chip. This was achievable by using the parent
with the same clock rate and no divider. So the incorrect divider setting
did not affect this usage.
Commit 946797aa3f ("clk: sunxi-ng: Support fixed post-dividers on MP
style clocks") added a new field to the ccu_mp structure, which broke
the aforementioned alignment. Now the system crashes as div_ops tries
to look up a nonexistent table.
Reported-by: Philipp Rossak <embed3d@gmail.com>
Tested-by: Philipp Rossak <embed3d@gmail.com>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: <stable@vger.kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
The audio blocks require specific clock rates. Until now we were using
the closest clock rate possible with integer N-M factors. This resulted
in audio playback being slightly slower than it should be.
The vendor kernel gets around this (for newer SoCs) by using sigma-delta
modulation to generate a fractional-N factor. As the PLL hardware is
identical in most chips, we can back port the settings from the newer
SoC, in this case the H3, onto the A31.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The HDMI DDC clock found in the CCU is the parent of the actual DDC
clock within the HDMI controller. That clock is also named "hdmi-ddc".
Rename the one in the CCU to "ddc". This makes more sense than renaming
the one in the HDMI controller to something else.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: Maxime Ripard <maxime.ripard@free-electrons.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: "Emilio López" <emilio@elopez.com.ar>
Cc: Peter De Schrijver <pdeschrijver@nvidia.com>
Cc: Prashant Gaikwad <pgaikwad@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Tero Kristo <t-kristo@ti.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-mediatek@lists.infradead.org
Cc: linux-renesas-soc@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-omap@vger.kernel.org
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Alexandre TORGUE <alexandre.torgue@st.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
On the A83T, the AHB1 clock has a shared pre-divider on the two
PLL-PERIPH clock parents. To support such instances of shared
pre-dividers, this patch extends the mux clock type to support
multiple variable pre-dividers.
As the pre-dividers are only used to calculate the rate, but
do not participate in the factorization process, this is fairly
straightforward.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The register offset for the lcd1-ch1 clock was incorrectly pointing to
the lcd0-ch1 clock. This resulted in the lcd0-ch1 clock being disabled
when the clk core disables unused clocks. This then stops the simplefb
HDMI output path.
Reported-by: Bob Ham <rah@settrans.net>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: stable@vger.kernel.org # 4.9.x-
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The enable bit offset for the hdmi-ddc module clock is wrong. It is
pointing to the main hdmi module clock enable bit.
Reported-by: Bob Ham <rah@settrans.net>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Cc: stable@vger.kernel.org # 4.9.x-
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
As the SPDIF was rarely documented on the earlier Allwinner SoCs
it was assumed that it had a similar clock register to the one
described in the H3 User Manual.
However this is not the case and it looks to shares the same setup
as the I2S clock registers.
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The PLL-MIPI clock is somewhat special as it has its own LDOs which
need to be turned on for this PLL to actually work and output a clock
signal.
Add the 2 LDO enable bits to the gate bits. This fixes issues with
the TCON not sending vblank interrupts when the tcon and dot clock are
indirectly clocked from the PLL-MIPI clock.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
On the A31, the DMA engine only works if AHB1 is clocked from PLL6.
In addition, the hstimer is clocked from AHB1, and if AHB1 is clocked
from the CPU clock, and cpufreq is working, we get an unstable timer.
Force the AHB1 clock to use PLL6 as its parent. Previously this was done
in the device tree with the assigned-clocks and assigned-clocks-parent
bindings. However with this new monolithic driver, the system critical
clocks aren't exported through the device tree. The alternative is to
force this setting in the driver before the clocks are registered.
This is also done in newer versions of mainline U-boot. But people still
using an older version, or even the vendor version, can still hit this
issue. Hence the need to do it in the kernel as well.
Reported-by: Hans de Goede <hdegoede@redhat.com>
Reported-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
The register offset for the mipi-csi clk is off by 4, a copy paste
error from the mipi-dsi clk.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The PLLs have a "lock" bit in their configuration registers which
indicate if the PLL has locked on to the requested clock rate. We
check this bit in the .set_rate op. The PLL cannot lock on if it's
not running, which might be a false positive (warning).
Set the CLK_SET_RATE_UNGATE flag for all PLLs so whenever clk_set_rate
is called on them, they get enabled and the "lock" check is really
checking the PLL.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
The LCD controller and HDMI controller use the LCDx-CHy and HDMI clocks
to generate their dot clocks. To be able to generate a full range of
possible clock rates, the parent PLL clock rates should also be changed.
Fixes: c6e6c96d8f ("clk: sunxi-ng: Add A31/A31s clocks")
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Add a new style driver for the clock control unit in Allwinner A31/A31s.
A few clocks are still missing:
- MIPI PLL's HDMI mode support
- EMAC clock
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Chen-Yu Tsai