This patch refactors the existing error detection and collection code,
placing most of it in i915_handle_error(). Additionally, we introduce a
work queue for scheduling post-crash tasks such as generating a uevent.
Using the uevent facility, userspace should be able to capture a
post-mortem dump for diagnostics.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Ben Gamari <bgamari.foss@gmail.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch from jbarnes and myself adds FIFO watermark control to the
driver. This is needed for both power saving features on new platforms
with the so-called "big FIFO" and for controlling FIFO allocation
between pipes in multi-head configurations.
It's also necessary infrastructure to support things like framebuffer
compression and configuration supportability checks (i.e. checking a
configuration against available bandwidth).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This patch enables error detection by enabling several types of error
interrupts. When an error interrupt is received, the interrupt
handler captures the error state; hopefully resulting in an accurate
set of error data (error type, active head pointer, etc.). The new
record is then available from sysfs. The current code will also dump
the error state to the system log.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Update interrupt handling methods for IGDNG with new registers
for display and graphics interrupt functions. As we won't use
irq-based vblank sync in dri2, so display interrupt on new chip
will be used for hotplug only in future.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
All G4x and newer chips use the new style frame count register, with a
full 32 bit frame count. Update the code to reflect this.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Disable OpRegion support for now until verified on new chipsets.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Add VGA port hotplug detection to the i915 driver. When KMS is enabled,
plugging in or removing a VGA cable from the VGA connector will
generate a uevent, which indicates to userspace that it should re-probe
outputs on this device (to determine modes, etc.).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
[anholt: dropped extra PORT_HOTPLUG_STAT clear with ack from jbarnes]
Signed-off-by: Eric Anholt <eric@anholt.net>
This could be triggered by a client asking to emit an irq when the device
wasn't initialized.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
As discussed in the long thread about vblank related timeouts, it turns out
GM45 has different frame count registers than previous chips. This patch
adds support for them, which prevents us from waiting on really stale
sequence values in drm_wait_vblank (which rather than returning immediately
ends up timing out or getting interrupted).
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In some cases userland may be confused and try to wait on vblank events from
pipes that aren't actually enabled. We shouldn't allow this, so return
-EINVAL if the pipe isn't on.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This commit adds i915 driver support for the DRM mode setting APIs.
Currently, VGA, LVDS, SDVO DVI & VGA, TV and DVO LVDS outputs are
supported. HDMI, DisplayPort and additional SDVO output support will
follow.
Support for the mode setting code is controlled by the new 'modeset'
module option. A new config option, CONFIG_DRM_I915_KMS controls the
default behavior, and whether a PCI ID list is built into the module for
use by user level module utilities.
Note that if mode setting is enabled, user level drivers that access
display registers directly or that don't use the kernel graphics memory
manager will likely corrupt kernel graphics memory, disrupt output
configuration (possibly leading to hangs and/or blank displays), and
prevent panic/oops messages from appearing. So use caution when
enabling this code; be sure your user level code supports the new
interfaces.
A new SysRq key, 'g', provides emergency support for switching back to
the kernel's framebuffer console; which is useful for testing.
Co-authors: Dave Airlie <airlied@linux.ie>, Hong Liu <hong.liu@intel.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This is step one towards having multiple masters sharing a drm
device in order to get fast-user-switching to work.
It splits out the information associated with the drm master
into a separate kref counted structure, and allocates this when
a master opens the device node. It also allows the current master
to abdicate (say while VT switched), and a new master to take over
the hardware.
It moves the Intel and radeon drivers to using the sarea from
within the new master structures.
Signed-off-by: Dave Airlie <airlied@redhat.com>
drivers/gpu/drm/i915/i915_irq.c: In function 'i915_disable_pipestat':
drivers/gpu/drm/i915/i915_irq.c:101: warning: control may reach end of non-void function 'i915_pipestat' being inlined
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
drm vblank initialization keeps track of the changes in driver-supplied
frame counts across vt switch and mode setting, but only if you let it by
not tearing down the drm vblank structure.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Because we write pipestat before iir, it's possible that a pipestat
interrupt will occur between the pipestat write and the iir write. This
leaves pipestat with an interrupt status not visible in iir. This may cause
an interrupt flood as we never clear the pipestat event.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The IMR masking was a technique recommended for avoiding getting stuck with
no interrupts generated again in MSI mode. It kept new IIR bits from getting
set between the IIR read and the IIR write, which would have otherwise
prevented an MSI from ever getting generated again. However, this caused a
problem for vblank as the IMR mask would keep the pipe event interrupt from
getting reflected in IIR, even after the IMR mask was brought back down.
Instead, just check the state of IIR after we ack the interrupts we're going
to handle, and restart if we didn't get IIR all the way to zero.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pipestat fields affect reporting of all vblank-related interrupts, so we
have to reset them during the irq_handler, and while enabling vblank
interrupts. Otherwise, if a pipe status field had been set to non-zero
before enabling reporting, we would never see an interrupt again.
This patch adds i915_enable_pipestat and i915_disable_pipestat to abstract
out the steps needed to change the reported interrupts.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Addresses in the hardware status page below index 0x20 are reserved for use
by the hardware. The legacy breadcrumb was sitting at index 5. Move it to
index 0x21, and make sure everyone uses the defined value instead of
hard-coded constants.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
When userland detected that this ioctl was supported (by version number check),
it used it in a racy way -- dispatch delayed swap, wait for vblank, continue
rendering. As there was no mechanism for it to wait for the swap to finish,
sometimes it would render before the swap and garbage would be displayed on
the screen.
By removing the ioctl and returning -EINVAL, userland returns to its previous,
correct rendering path of waiting for a vblank then dispatching a swap. The
only path that could have used this ioctl correctly was page flipping, which
relied on only one client running and emitting wait-for-vblank-before-rendering
in the command stream. That path also falls back correctly, at the performance
cost of not being able to queue up rendering before the flip occurs.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@linux.ie>
vblank in the kernel is far simpler if it deals with pipes instead of
planes, so we're changing both user and kernel side.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
To synchronize clip lists with the X server, the DRM lock must be held while
looking at drawable clip lists. To synchronize with other ring access, the
ring mutex must be held while inserting commands into the ring. Failure to
do the first resulted in easy visual corruption when moving windows, and the
second could have corrupted the ring with DRI2.
Grabbing the DRM lock involves using the DRM tasklet mechanism, grabbing the
ring mutex means potentially sleeping. Deal with both of these by always
running the tasklet from a work handler.
Also, protect from clip list changes since the vblank request was queued by
making sure the window has at least one rectangle while looking inside,
preventing oopses .
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Otherwise, if we lost the race, the pipestat bit would be set without being
reflected in IIR, and we would never clear the pipestat bit so the pipe
event would never be generated again, and all vblank waits would time out.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If the failing paths were hit, the vblank IRQ would never get turned off
again.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This uses the same spinlock as the user_irq code as it shares the same
register, ensuring that interrupt registers are updated atomically.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
We fail ioctls that depend on the sarea_priv with EINVAL.
Signed-off-by: Kristian Høgsberg <krh@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
In the conversion for GEM, we had stopped using the hardware lock to protect
ring usage, since it was all internal to the DRM now. However, some paths
weren't converted to using struct_mutex to prevent multiple threads from
concurrently working on the ring, in particular between the vblank swap handler
and ioctls.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GEM allows the creation of persistent buffer objects accessible by the
graphics device through new ioctls for managing execution of commands on the
device. The userland API is almost entirely driver-specific to ensure that
any driver building on this model can easily map the interface to individual
driver requirements.
GEM is used by the 2d driver for managing its internal state allocations and
will be used for pixmap storage to reduce memory consumption and enable
zero-copy GLX_EXT_texture_from_pixmap, and in the 3d driver is used to enable
GL_EXT_framebuffer_object and GL_ARB_pixel_buffer_object.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Previously, drivers supporting vblank interrupt waits would run the interrupt
all the time, or all the time that any 3d client was running, preventing the
CPU from sleeping for long when the system was otherwise idle. Now, interrupts
are disabled any time that no client is waiting on a vblank event. The new
method uses vblank counters on the chipsets when the interrupts are turned
off, rather than counting interrupts, so that we can continue to present
accurate vblank numbers.
Co-author: Michel Dänzer <michel@tungstengraphics.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds the support necessary for allowing ACPI backlight control to
work on some newer Intel-based graphics systems. Tested on Thinkpad T61
and HP 2510p hardware.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Previous attempts at interrupt mitigation had been foiled by i915_wait_irq's
failure to update the sarea seqno value when the status page indicated that
the seqno had already been passed. MSI support has been seen to cut CPU
costs by up to 40% in some workloads by avoiding other expensive interrupt
handlers for frequent graphics interrupts.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With the coming of kernel based modesetting and the memory manager stuff,
the everything in one directory approach was getting very ugly and
starting to be unmanageable.
This restructures the drm along the lines of other kernel components.
It creates a drivers/gpu/drm directory and moves the hw drivers into
subdirectores. It moves the includes into an include/drm, and
sets up the unifdef for the userspace headers we should be exporting.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Frans Pop