Sync-up ibss beacon timer with the beacon frame's timestamp. When the
node acts as joiner, it has to sync with the received beacon timestamp
instead of reading tsf from hw. As the hw tsf wont wont be update till
bssid is configured. This patch programs hw tsf with the received beacon
timestamp if beacon timers are yet to be configured.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since it's only called when beacons are stuck, move it to the SWBA handler
tasklet, to avoid doing redundant checks on every single interrupt.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 provides short preamble information and ERP protection
information on a per-BSS basis, which can be used. Remove flags
stored in the driver, which was incorrect since they were being used
in a global manner.
Signed-off-by: Sujith Manoharan <c_manoha@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The approach of this change is flawed, as it triggers tx status processing
from more callsites, yet the chips only have one global tx status queue.
Subsequent patches will properly fix the issue that this one tried to address.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for EDMA chip AR_Q_TXE (tx enable for each queue) is read only
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ATH_DBG_ to macros to shorten the uses and
reduce the line count.
Coalesce ath_dbg formats.
Add missing spaces to coalesced formats.
Add missing newline terminations to ath_dbg formats.
Align ath_dbg arguments where appropriate.
Standardize ath_dbg formats without periods.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the new API, tx descriptors can be written in one single pass
instead of having to re-read and rewrite fields from multiple places.
This makes the code easier to read and also slightly improves performance
on embedded MIPS hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This ensures that only ath9k_hw_set_desc_link needs to recalculate the tx
descriptor checksum on AR9380+
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When starting the AP beacon timer, it assumes that the TSF has recently
been cleared. Set the SC_OP_TSF_RESET flag to ensure that this is always
the case.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes it much easier to add further rework to avoid race conditions
between reset and other work items.
Move other functions to make ath_reset static.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we already have ah->{rx,tx}chainmask for the same purpose
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The received tx status of aggregated frame without BlockAck may
cause deaf state in AR5416 cards. So the driver does a reset to
recover. When this happens, we release the pcu_lock before doing
a reset as ath_rest acquires pcu_lock. This is ugly and also not
atomic. Fixing this addresses the TX DMA failure also.
ath_tx_complete_aggr can be called from different paths which
takes different variants of spin_lock. This patch also addresses
the following warning.
WARNING: at kernel/timer.c:1011 del_timer_sync+0x4e/0x50()
Call Trace:
<IRQ> [<ffffffff8104be3a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104be85>] warn_slowpath_null+0x15/0x20
[<ffffffff8105915e>] del_timer_sync+0x4e/0x50
[<ffffffffa03726be>] ath_reset+0x3e/0x210 [ath9k]
[<ffffffff8135cdaf>] ? _raw_spin_unlock_bh+0x1f/0x30
[<ffffffffa037760a>] ath_tx_complete_aggr.isra.26+0x54a/0xa40 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The edma based (AR9003 family) chips update tx status
descriptors in a common ring buffer for all transmitted
frames. Whenever tx interrupt is raised, the descriptors
are processed and tx status index is moved.
The complete tx stauts ring are updated with beacons tx status
when there are no data frames to be sent for a period of time.
In this state, transmitting data frames causes the driver to
wait for the tx status on an incorrect tx status index though
the status was updated by hw properly. The driver detects this
condition as a h/w hang and does unnecessary chip resets.
This issue was orginally reported in adhoc mode while sending
frames after an idle time.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix ensure the timers to be set at beacon interval boundaries.
Without this change timers can be set improperly resulting in the absence of beacons.
Signed-off-by: Fabrice Deyber <fabricedeyber@agilemesh.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier beacon_interval is used to hold interval value and
some flags (ATH9K_BEACON_ENA &ATH9K_BEACON_PERIOD). So to
extract interval ATH9K_BEACON_PERIOD is used. Those flags
were completely removed. So masking beacon_interval is
not required.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rounding up the delta between last-beacon-tsf and tsf to intval is wrong
and can lead to misconfigured timers which breaks beacon transmission.
Fix this by adding intval and subtracting the offset of the tsf within the
current slot.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ad-hoc mode, beacon timers are configured differently compared to AP
mode, and (depending on the scenario) can vary enough to make the beacon
tasklet not detect slot 0 based on the TSF.
Since staggered beacons are not (and cannot be) used in ad-hoc mode, it
makes more sense to just hardcode slot 0 here, avoiding unnecessary
TSF reads and calculations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assumsion is that while processing ath9k tasklet,
interrupts were already disabled and it will be enabled
at the completion of ath9k tasklet. But whenever TSFOOR is raised,
the driver configures the beacon timers after having received a
beacon frame from the AP which inturn enables the interrupts.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Requesting beacon sync up to configure beacon timers properly
in hw, has be done after doing beacon config with default values.
Setting the flags in beacon config is causing the device to not
enter into network sleep on idle state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While leaving the oper channel, beacon generation is stopped
by mac80211 and beacon slots are marked as inactive.
During the scan, ath9k configures beacon timers
based on IEEE80211_CONF_OFFCHANNEL which inturn generates
beacon alert even though bslot is inactive.
ath9k fails to disable beacon alert while moving to offchannel
if none of the beacon slot is active. This is causing beacon
transmission on foreign channel. This patch enables swba
based on active bslots.
This issue was reported with two vifs (AP+STA) and triggered
scan in STA vif in unassociated state.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Request a re-configuration of Beacon related timers
on the receipt of the first Beacon frame has to be set only
for station mode. Setting beacon sync for IBSS is causing
wrong beacon slot selection on beacon generation.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit "ath9k: configure beacons based on hw opmode" introduced
a regression which leads to kernel panic. Failed to stop ani timer
during the driver unload while any of the beaconing vif is running.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Current ath9k code does not handle beacon timers on opmode
specific. One such example is that a STA beacon config overwrites
already configured AP vif's beacon timers during scan.
On multi station vif case, configure beacon timers beased
on primary vif selected. This also helps while moving back
to single STA vif from multi STA vifs, where the power save
is enabled and hw has to be reconfigured with proper
beacon and bssid/aid. Otherwise connection poll will be triggered
so frequently due to beacon loss.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unused bssid from ath_vif and set av_bslot on beacon
alloc/return.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since the beacon timers are global, the individual vif type should not
be used to determine the beacon timer configuration mode, use the
global opmode instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The recent cleanups in the beacon code fixed SWBA backoff calculation,
however it did not remove a line of code that worked around the issues
from the earlier version of the code.
After the cleanup, the initial TSF based slot calculation now always
returns 0 instead of ATH_BCBUF-1, so the previous hack that reversed the
slot order needs to be removed, as ad-hoc mode does not use staggered
beacons.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stuck beacon detection is supposed to trigger when 9 consecutive beacons
could not be sent by the hardware. When the driver runs only one active
AP mode interface, it still configures the hardware beacon timer for
4 (ATH_BCBUF) beacon slots slots, which causes stuck beacon detection
to be reset if ath9k_hw_stoptxdma clears the stuck frames between
SWBA intervals.
Fix this by not resetting the missed beacon count for empty slots and
multiplying the threshold not by the maximum number of beacon slots
but by the configured number of beacon interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Single missed (i.e. not transmitted) beacons in AP mode are not very rare
and not necessarily an indicator of strong interference, so only trigger
noise floor recalibration when multiple consecutive beacons could not
be transmitted.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AP mode beacon timers in ath9k are configured in milliseconds, which breaks
when increasing ATH_BCBUF to 8 instead of 4 (due to rounding errors).
Since the hardware timers are actually configured in microseconds, it's
better to let the driver use that unit directly.
To be able to do that, the beacon interval parameter abuse for passing
certain flags needs to be removed. This is easy to do, because those flags
are completely unnecessary anyway. ATH9K_BEACON_ENA is ignored,
ATH9K_BEACON_RESET_TSF can be replaced with calling ath9k_hw_reset_tsf
from the driver directly.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k calls ath9k_hw_stoptxdma every time it sends a beacon, however there
is not much point in doing that if the previous beacon and mcast traffic
went out properly. On AR9380, calling that function too often can result
in an increase of stuck beacons due to differences in the handling of the
queue enable/disable functionality.
With this patch, the queue will only be explicitly stopped if the previous
data frames were not sent successfully. With the beacon code being the
only remaining user of ath9k_hw_stoptxdma, this function can be simplified
in order to remove the now pointless attempts at waiting for transmission
completion, which would never happen at this point due to the different
method of tx scheduling of the beacon queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Beaconing should be disabled before stopping beacon queue.
Not doing so could queue up beacons in hw that causes
failure to stop Tx DMA, due to pending frames in hw
and also unnecessary beacon tasklet schedule.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The variable appears in both ath_softc and ath_beacon_config.
The struct ath_beacon_config is embedded in ath_softc. The redundant
variable was added by commit id 57c4d7b4c4.
Signed-off-by: Steve Brown <sbrown@cortland.com>
Reviewed-by: Mohammed Shafi <shafi.ath9k@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add few comments for not parsing DTIM period from mac80211
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When beacons are being added or removed for an interface, ieee80211_beacon_get
will sometimes not return a beacon. This is normal and should not result in
useless logspam.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When using a mixture of AP and Station interfaces,
the hardware mode was using the type of the
last VIF registered. Instead, we should keep track
of the number of different types of vifs and set the
mode accordingly.
In addtion, use the vif type instead of hardware opmode
when dealing with beacons.
Attempt to move some of the common setup code into smaller
methods so we can re-use it when changing vif mode as
well as adding/deleting vifs.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some minor clean ups in assigning values to beacon config parameters
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove ath/debug.h and the includes of these files.
Coalesce long formats.
Correct a few misspellings and missing "\n"s from these logging messages.
Remove unnecessary trailing space before a newline.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
So these errors are always emitted at KERN_ERR level.
Remove ARRAY_SIZE casts, use printf type %zu
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This feature is to mitigate the problem of certain 3
stream chips that exceed the PCIe power requirements.An EEPROM flag
controls which chips have APM enabled which is basically read from
miscellaneous configuration element of the EEPROM header.
This workaround will reduce power consumption by using 2 Tx chains for
Single and Double stream rates (5 GHz only).All self generated frames
(regardless of rate) are sent on 2 chains when this feature is
enabled(Chip Limitation).
Cc: Paul Shaw <paul.shaw@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Merge initial processing for the CAB queue and regular tx.
Also move ath_tx_cabq() to beacon.c and make it static.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rajkumar Manoharan