Remove the tty_vhangup() from the pty code and just release the
redirect. The tty_vhangup() results in data loss and data out of order
issues.
If you write to a pty master an immediately close the pty master, the
receiver might get a chunk of data dropped, but then receive some later
data. That's obviously something rather unexpected for a user. It
certainly confused my test program.
It turns out that tty_vhangup() on the slave pty gets called from
pty_close(), and that causes the data on the slave side to be flushed,
but due to races more data can be copied into the slave side's buffer
after that. Consider the following sequence:
thread1 thread2 thread3
------- ------- -------
| |-write data into buffer,
| | n_tty buffer is filled
| | along with other buffers
| |-pty_close(master)
| |--tty_vhangup(slave)
| |---tty_ldisc_hangup()
| |----n_tty_flush_buffer()
| |-----reset_buffer_flags()
|-n_tty_read() |
|--up_read(&tty->termios_rwsem);
| |------down_read(&tty->termios_rwsem)
| |------clear n_tty buffer contents
| |------up_read(&tty->termios_rwsem)
|--tty_buffer_flush_work() |
|--schedules work calling |
| flush_to_ldisc() |
| |-flush_to_ldisc()
| |--receive_buf()
| |---tty_port_default_receive_buf()
| |----tty_ldisc_receive_buf()
| |-----n_tty_receive_buf2()
| |------n_tty_receive_buf_common()
| |-------down_read(&tty->termios_rwsem)
| |-------__receive_buf()
| | copies data into n_tty buffer
| |-------up_read(&tty->termios_rwsem)
|--down_read(&tty->termios_rwsem)
|--copy buffer data to user
>From this sequence, you can see that thread2 writes to the buffer then
only clears the part of the buffer in n_tty. The n_tty receive buffer
code then copies more data into the n_tty buffer.
But part of the vhangup, releasing the redirect, is still required to
avoid issues with consoles running on pty slaves. So do that.
As far as I can tell, that is all that should be required.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20201124004902.1398477-3-minyard@acm.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This will be required by the pty code when it removes tty_vhangup() on
master close.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Link: https://lore.kernel.org/r/20201124004902.1398477-2-minyard@acm.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The transmission complete error message provides the status of the
ISR_USART_TC bit. This bit, when set, indicates that the transmission
has not been completed.
The bit status indication is not a very understandable information.
The error message sent on console should indicate that the transmission is
not complete, instead of providing USART_TC bit status.
Update the error message and add a comment for better understanding.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-9-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Clean probe and remove port deinit by moving clk_disable_unprepare in a
new dedicated deinit_port function.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-8-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The comment for conflicting RTS/CTS config refers to "st, hw-flow-ctrl",
but this property is deprecated since the generic RTS/CTS property has
been introduced by the patch 'serial: stm32: Use generic DT binding for
announcing RTS/CTS lines'.
Update the comment to refer to both generic and deprecated RTS/CTS
properties.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-7-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Adds the prefix "_usart" in the name of stm32 usart functions in order to
ease the usage of kernel trace and tools, such as f-trace.
Allows to trace "stm32_usart_*" functions with f-trace. Without this patch,
all the driver functions needs to be added manually in f-trace filter.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-4-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes checkpatch --strict warnings and checks:
- checkpatch --strict "Unnecessary parentheses"
- checkpatch --strict "Blank lines aren't necessary before a close brace
- checkpatch --strict "Alignment should match open parenthesis"
- checkpatch --strict "Please don't use multiple blank lines"
- checkpatch --strict "Comparison to NULL could be written ..."
- visual check code ordering warning
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-3-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
DMA initialization error handling is not properly implemented in the
driver.
Fix DMA initialization error handling by:
- moving TX DMA descriptor request error handling in a new dedicated
fallback_err label
- adding error handling to TX DMA descriptor submission
- adding error handling to RX DMA descriptor submission
This patch depends on '24832ca3ee85 ("tty: serial: stm32-usart: Remove set
but unused 'cookie' variables")' which unfortunately doesn't include a
"Fixes" tag.
Fixes: 3489187204 ("serial: stm32: adding dma support")
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Link: https://lore.kernel.org/r/20210106162203.28854-2-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The main purpose of tty_port::low_latency was removed in commit
a9c3f68f3c (tty: Fix low_latency BUG) back in 2014. It was left in
place for drivers as an optional tune knob. But only one driver has been
using it until the previous commit. So remove this misconcept
completely, given there are no users.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the only in-kernel user of tty_port::low_latency. Switch this
last one to test uport->flags directly as tty_port::low_latency is going
away in the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drop support for these ioctls:
* PIO_FONT, PIO_FONTX
* GIO_FONT, GIO_FONTX
* PIO_FONTRESET
As was demonstrated by commit 90bfdeef83 (tty: make FONTX ioctl use
the tty pointer they were actually passed), these ioctls are not used
from userspace, as:
1) they used to be broken (set up font on current console, not the open
one) and racy (before the commit above)
2) KDFONTOP ioctl is used for years instead
Note that PIO_FONTRESET is defunct on most systems as VGA_CONSOLE is set
on them for ages. That turns on BROKEN_GRAPHICS_PROGRAMS which makes
PIO_FONTRESET just return an error.
We are removing KD_FONT_FLAG_OLD here as it was used only by these
removed ioctls. kd.h header exists both in kernel and uapi headers, so
we can remove the kernel one completely. Everyone includeing kd.h will
now automatically get the uapi one.
There are now unused definitions of the ioctl numbers and "struct
consolefontdesc" in kd.h, but as it is a uapi header, I am not touching
these.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The constant 20 makes the font sum computation signed which can lead to
sign extensions and signed wraps. It's not much of a problem as we build
with -fno-strict-overflow. But if we ever decide not to, be ready, so
switch the constant to unsigned.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tty->ops->close is always called with a valid tty, so the BUG_ON cannot
trigger.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 5ce2087ed0 (Fix default compose table initialization) fixed
unicode table so that the values are not sign extended. The upstream
(kbd package) chose a different approach. They use hexadecimal values.
So use the same, so that the output of loadkeys and our shipped file
correspond more to each other.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
loadkeys (from kbd) generates 'unsigned short' instead of 'u_short'
since 2.0.3. It also marks maps as 'static' for longer than kbd's
history.
So adapt the shipped defkeymap.c to conform more to loadkeys output.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the last extern user of the tasklet (set_leds) is in
keyboard.c, we can make keyboard_tasklet local to this unit too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_leds and compute_shiftstate are called from a single place in vt.c.
Let's combine these two into vt_set_leds_compute_shiftstate. This allows
for making keyboard_tasklet local in the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210105120239.28031-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c685af1108 ("serial: mvebu-uart: fix tx lost characters") fixed tx
lost characters at low baud rates but started causing tx lost characters
when kernel is going to power off or reboot.
TX_EMP tells us when transmit queue is empty therefore all characters were
transmitted. TX_RDY tells us when CPU can send a new character.
Therefore we need to use different check prior transmitting new character
and different check after all characters were sent.
This patch splits polling code into two functions: wait_for_xmitr() which
waits for TX_RDY and wait_for_xmite() which waits for TX_EMP.
When rebooting A3720 platform without this patch on UART is print only:
[ 42.699�
And with this patch on UART is full output:
[ 39.530216] reboot: Restarting system
Fixes: c685af1108 ("serial: mvebu-uart: fix tx lost characters")
Signed-off-by: Pali Rohár <pali@kernel.org>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20201223191931.18343-1-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
spinlock can be initialized automatically with DEFINE_SPINLOCK()
rather than explicitly calling spin_lock_init().
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Link: https://lore.kernel.org/r/20201223141438.889-1-zhengyongjun3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In order to use xmon with powerpc 8xx, the serial driver
must provide udbg_putc() and udpb_getc().
Provide them via cpm_put_poll_char() and cpm_get_poll_char().
This requires CONFIG_CONSOLE_POLL.
Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Link: https://lore.kernel.org/r/e4471bf81089252470efb3eed735d71a5b32adbd.1608716197.git.christophe.leroy@csgroup.eu
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For a given struct tty_struct this yields the corresponding statistics
about sent and received characters (and some more) which is needed to
implement an LED trigger for tty devices.
The new function is then used to simplify tty_tiocgicount().
Reviewed-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201218104246.591315-3-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new function tty_kopen_shared() that yields a struct
tty_struct. The semantic difference to tty_kopen() is that the tty is
expected to be used already. So rename tty_kopen() to
tty_kopen_exclusive() for clearness, adapt the single user and put the
common code in a new static helper function.
tty_kopen_shared is to be used to implement an LED trigger for tty
devices in one of the next patches.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20201218104246.591315-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This series adds:
* New drivers and OpenRISC support for the LiteX platform
* A bug fix to support userspace gdb debugging
* Fixes one compile issue with blk-iocost
-----BEGIN PGP SIGNATURE-----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=zTkl
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/openrisc/linux
Pull OpenRISC updates from Stafford Horne:
- New drivers and OpenRISC support for the LiteX platform
- A bug fix to support userspace gdb debugging
- Fixes one compile issue with blk-iocost
* tag 'for-linus' of git://github.com/openrisc/linux:
openrisc: add local64.h to fix blk-iocost build
openrisc: fix trap for debugger breakpoint signalling
openrisc: add support for LiteX
drivers/tty/serial: add LiteUART driver
dt-bindings: serial: document LiteUART bindings
drivers/soc/litex: add LiteX SoC Controller driver
dt-bindings: soc: document LiteX SoC Controller bindings
dt-bindings: vendor: add vendor prefix for LiteX
-----BEGIN PGP SIGNATURE-----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=1gUa
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Finally allow parallel writes and reads into/from the lockless
ringbuffer. But it is not a complete solution. Readers are still
serialized against each other. And nested writes are still prevented
by printk_safe per-CPU buffers.
- Use ttynull as the ultimate fallback for /dev/console.
- Officially allow disabling console output by using console="" or
console=null
- A few code cleanups
* tag 'printk-for-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
printk: remove logbuf_lock writer-protection of ringbuffer
printk: inline log_output(),log_store() in vprintk_store()
printk: remove obsolete dead assignment
printk/console: Allow to disable console output by using console="" or console=null
init/console: Use ttynull as a fallback when there is no console
printk: ringbuffer: Reference text_data_ring directly in callees.
Here is the "large" set of tty and serial patches for 5.11-rc1.
Nothing major at all, some cleanups and some driver removals, always a
nice sign:
- build warning cleanups
- vt locking and logic unwinding and cleanups
- tiny serial driver fixes and updates
- removal of the synclink serial driver as it's no longer needed
- removal of dead termiox code
All of this has been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iGrw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yk6ZwCgurjtlXOdtrjM6kcvYfKZcILS7jQAoK1B1rH9
O6fVeZl8qRDWL4p06y2s
=0Uho
-----END PGP SIGNATURE-----
Merge tag 'tty-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the "large" set of tty and serial patches for 5.11-rc1.
Nothing major at all, some cleanups and some driver removals, always a
nice sign:
- build warning cleanups
- vt locking and logic unwinding and cleanups
- tiny serial driver fixes and updates
- removal of the synclink serial driver as it's no longer needed
- removal of dead termiox code
All of this has been in linux-next for a while with no reported issues"
* tag 'tty-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (89 commits)
serial: 8250_pci: Drop bogus __refdata annotation
tty: serial: meson: enable console as module
serial: 8250_omap: Avoid FIFO corruption caused by MDR1 access
serial: imx: Move imx_uart_probe_dt() content into probe()
serial: imx: Remove unneeded of_device_get_match_data() NULL check
tty: Fix whitespace inconsistencies in vt_io_ioctl
serial_core: Check for port state when tty is in error state
dt-bindings: serial: Update DT binding docs to support SiFive FU740 SoC
tty: use const parameters in port-flag accessors
tty: use assign_bit() in port-flag accessors
earlycon: drop semicolon from earlycon macro
tty: Remove dead termiox code
tty/serial/imx: Enable TXEN bit in imx_poll_init().
tty : serial: jsm: Fixed file by adding spacing
tty: serial: uartlite: Support probe deferral
earlycon: simplify earlycon-table implementation
tty: serial: bcm63xx: lower driver dependencies
serial: mxs-auart: Remove unneeded platform_device_id
serial: 8250-mtk: Fix reference leak in mtk8250_probe
serial: imx: Remove unused .id_table support
...
Since commit d73dfc6a41 ("serial: 8250_pci: remove __devexit
usage") in v3.9, the 8250/16550 PCI serial driver no longer has any code
or data located in initmem, hence there is no need to annotate the
pci_serial_quirks structure with __refdata. Drop the annotation, to
avoid suppressing future section warnings.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201211133907.2970460-1-geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enable serial driver to be built as a module. To do so, init the
console support on driver/module load instead of using
console_initcall().
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201211005744.12855-1-khilman@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been observed that once per 300-1300 port openings the first
transmitted byte is being corrupted on AM3352 ("v" written to FIFO appeared
as "e" on the wire). It only happened if single byte has been transmitted
right after port open, which means, DMA is not used for this transfer and
the corruption never happened afterwards.
Therefore I've carefully re-read the MDR1 errata (link below), which says
"when accessing the MDR1 registers that causes a dummy under-run condition
that will freeze the UART in IrDA transmission. In UART mode, this may
corrupt the transferred data". Strictly speaking,
omap_8250_mdr1_errataset() performs a read access and if the value is the
same as should be written, exits without errata-recommended FIFO reset.
A brief check of the serial_omap_mdr1_errataset() from the competing
omap-serial driver showed it has no read access of MDR1. After removing the
read access from omap_8250_mdr1_errataset() the data corruption never
happened any more.
Link: https://www.ti.com/lit/er/sprz360i/sprz360i.pdf
Fixes: 61929cf016 ("tty: serial: Add 8250-core based omap driver")
Cc: stable@vger.kernel.org
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@gmail.com>
Link: https://lore.kernel.org/r/20201210055257.1053028-1-alexander.sverdlin@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the driver only probes via devicetree, we can move the
content of imx_uart_probe_dt() directly into imx_uart_probe() to
make the code simpler.
Suggested-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201209214712.15247-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the NULL check on
of_device_get_match_data() is no longer needed.
This check was only needed when this driver supported both DT and non-DT
platforms.
Remove the unneeded of_device_get_match_data() NULL check.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201126124643.3371-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
At the moment opening a serial device node (such as /dev/ttyS3)
succeeds even if there is no actual serial device behind it.
Reading/writing/ioctls fail as expected because the uart port is not
initialized (the type is PORT_UNKNOWN) and the TTY_IO_ERROR error state
bit is set fot the tty.
However setting line discipline does not have these checks
8250_port.c (8250 is the default choice made by univ8250_console_init()).
As the result of PORT_UNKNOWN, uart_port::iobase is NULL which
a platform translates onto some address accessing which produces a crash
like below.
This adds tty_port_initialized() to uart_set_ldisc() to prevent the crash.
Found by syzkaller.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Link: https://lore.kernel.org/r/20201203055834.45838-1-aik@ozlabs.ru
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, locking of ->session is very inconsistent; most places
protect it using the legacy tty mutex, but disassociate_ctty(),
__do_SAK(), tiocspgrp() and tiocgsid() don't.
Two of the writers hold the ctrl_lock (because they already need it for
->pgrp), but __proc_set_tty() doesn't do that yet.
On a PREEMPT=y system, an unprivileged user can theoretically abuse
this broken locking to read 4 bytes of freed memory via TIOCGSID if
tiocgsid() is preempted long enough at the right point. (Other things
might also go wrong, especially if root-only ioctls are involved; I'm
not sure about that.)
Change the locking on ->session such that:
- tty_lock() is held by all writers: By making disassociate_ctty()
hold it. This should be fine because the same lock can already be
taken through the call to tty_vhangup_session().
The tricky part is that we need to shorten the area covered by
siglock to be able to take tty_lock() without ugly retry logic; as
far as I can tell, this should be fine, since nothing in the
signal_struct is touched in the `if (tty)` branch.
- ctrl_lock is held by all writers: By changing __proc_set_tty() to
hold the lock a little longer.
- All readers that aren't holding tty_lock() hold ctrl_lock: By
adding locking to tiocgsid() and __do_SAK(), and expanding the area
covered by ctrl_lock in tiocspgrp().
Cc: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tiocspgrp() takes two tty_struct pointers: One to the tty that userspace
passed to ioctl() (`tty`) and one to the TTY being changed (`real_tty`).
These pointers are different when ioctl() is called with a master fd.
To properly lock real_tty->pgrp, we must take real_tty->ctrl_lock.
This bug makes it possible for racing ioctl(TIOCSPGRP, ...) calls on
both sides of a PTY pair to corrupt the refcount of `struct pid`,
leading to use-after-free errors.
Fixes: 47f86834bb ("redo locking of tty->pgrp")
CC: stable@kernel.org
Signed-off-by: Jann Horn <jannh@google.com>
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
set_termiox() and the TCGETX handler bail out with -EINVAL immediately
if ->termiox is NULL, but there are no code paths that can set
->termiox to a non-NULL pointer; and no such code paths seem to have
existed since the termiox mechanism was introduced back in
commit 1d65b4a088 ("tty: Add termiox") in v2.6.28.
Similarly, no driver actually implements .set_termiox; and it looks like
no driver ever has.
Delete this dead code; but leave the definition of struct termiox in the
UAPI headers intact.
Signed-off-by: Jann Horn <jannh@google.com>
Link: https://lore.kernel.org/r/20201203020331.2394754-1-jannh@google.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As described in Documentation, poll_init() is called by kgdb to initialize
hardware which supports both poll_put_char() and poll_get_char().
It's necessary to enable TXEN bit, otherwise, it will cause hardware fault
and kernel panic when calling imx_poll_put_char().
Generally, if use /dev/ttymxc0 as kgdb console as well as system
console, ttymxc0 is initialized early by system console which does enable
TXEN bit.But when use /dev/ttymxc1 as kgbd console, ttymxc1 is only
initialized by imx_poll_init() cannot enable the TXEN bit, which will
cause kernel panic.
Signed-off-by: Mingrui Ren <jiladahe1997@gmail.com>
Link: https://lore.kernel.org/r/20201202072543.151-1-972931182@qq.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Give uartlite a chance to be probed when IRQ controller will be finally
available and return potential -EPROBE_DEFER as-is. The condition "<="
has been changed to "<" to follow the recommendation in the header of
platform_get_irq().
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nokia.com>
Link: https://lore.kernel.org/r/20201127101953.23700-1-alexander.sverdlin@nokia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of using the array-of-pointers trick to avoid having gcc mess up
the earlycon array stride, specify type alignment when declaring entries
to prevent gcc from increasing alignment.
This is essentially an alternative (one-line) fix to the problem
addressed by commit dd709e72cb ("earlycon: Use a pointer table to fix
__earlycon_table stride").
gcc can increase the alignment of larger objects with static extent as
an optimisation, but this can be suppressed by using the aligned
attribute when declaring variables.
Note that we have been relying on this behaviour for kernel parameters
for 16 years and it indeed hasn't changed since the introduction of the
aligned attribute in gcc-3.1.
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20201123102319.8090-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hardware supported by bcm63xx is also used by BCM4908 SoCs family that
is ARM64. In future more architectures may need it as well. There is
nothing arch specific breaking compilation so just stick to requiring
COMMON_CLK.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Link: https://lore.kernel.org/r/20201125090608.28442-1-zajec5@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The mxs-auart driver is only used for DT platforms and there is no
need to use the platform_device_id structure.
Get rid the platform_device_id structure and retrieve the data via
of_device_get_match_data(), which simplifies the code.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201123190438.5636-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The pm_runtime_enable will increase power disable depth.
Thus a pairing decrement is needed on the error handling
path to keep it balanced according to context.
Fixes: e32a83c70c ("serial: 8250-mtk: modify mtk uart power and clock management")
Signed-off-by: Zhang Qilong <zhangqilong3@huawei.com>
Link: https://lore.kernel.org/r/20201119141126.168850-1-zhangqilong3@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl+69egeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGTSYH/ifRBlaxy5UiHFc0
2zdR7pkjWrYfDTTT3sazIAhdlzzcfnkUqgFxOP45F4ZIqeTzunH3sUY+5UlT9IX7
liUgnLxQ/1R9Gx8kPGQfu+tLCey78xVFydGsqJoW9sPRw2R+apMdGGa/lOrk+OXz
DXIN+dDnGFqwCCNJpK+rxQQhFf++IPpSI8z6Y23moOFhsDZrEziHuVFy2FGyRM6z
prZ/us/tcobE8ptCk1RmOxLoJ1DR6UxpA2vLimTE+JD8siOsSWPbjE0KudnWCnd5
BLqIjrsPJbSxyuzzK3v9dnO5wMv7tMDuMIuYM/MQTXDttNwtsqt/aP6gdnUCym7N
5eHEj5g=
=MuO1
-----END PGP SIGNATURE-----
Merge 5.10-rc5 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stdin, stdout, and stderr standard I/O stream are created for the init
process. They are not available when there is no console registered
for /dev/console. It might lead to a crash when the init process
tries to use them, see the commit 48021f9813 ("printk: handle
blank console arguments passed in.").
Normally, ttySX and ttyX consoles are used as a fallback when no consoles
are defined via the command line, device tree, or SPCR. But there
will be no console registered when an invalid console name is configured
or when the configured consoles do not exist on the system.
Users even try to avoid the console intentionally, for example,
by using console="" or console=null. It is used on production
systems where the serial port or terminal are not visible to
users. Pushing messages to these consoles would just unnecessary
slowdown the system.
Make sure that stdin, stdout, stderr, and /dev/console are always
available by a fallback to the existing ttynull driver. It has
been implemented for exactly this purpose but it was used only
when explicitly configured.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20201111135450.11214-2-pmladek@suse.com
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
.id_table support in this driver was only useful for old non-devicetree
platforms.
Get rid of the .id_table since it is no longer used.
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201115110341.22761-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Functions must follow directly on from their headers
- Demote non-conforming kernel-doc header
- Ensure notes have unique section names
- Provide missing description for 'reinit'
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_ldisc.c:158: warning: cannot understand function prototype: 'int tty_ldisc_autoload = IS_BUILTIN(CONFIG_LDISC_AUTOLOAD); '
drivers/tty/tty_ldisc.c:199: warning: Function parameter or member 'ld' not described in 'tty_ldisc_put'
drivers/tty/tty_ldisc.c:260: warning: duplicate section name 'Note'
drivers/tty/tty_ldisc.c:717: warning: Function parameter or member 'reinit' not described in 'tty_ldisc_hangup'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112105857.2078977-2-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/pmac_zilog.h:365:58: warning: variable ‘garbage’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linux-serial@vger.kernel.org
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112105857.2078977-5-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 5.10-rc1 i.MX is a devicetree-only platform and the existing
platform data support in this driver was only useful for old non-devicetree
platforms.
Get rid of the platform data support since it is no longer used.
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Link: https://lore.kernel.org/r/20201110214840.16768-1-festevam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We have for some time the assign_bit() API to replace open coded
if (foo)
set_bit(n, bar);
else
clear_bit(n, bar);
Use this API in VT keyboard library code.
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20201109105601.47159-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With commit 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable"),
below warning is seen with W=1 and CONFIG_SERIAL_8250_DMA is disabled:
drivers/tty/serial/8250/8250_omap.c:1199:42: warning: unused variable 'k3_soc_devices' [-Wunused-const-variable]
Fix this by moving the code using k3_soc_devices array to
omap_serial_fill_features_erratas() that handles other errata flags as
well.
Fixes: 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-2-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
k3_soc_devices array is missing a sentinel entry which may result in out
of bounds access as reported by kernel KASAN.
Fix this by adding a sentinel entry.
Fixes: 439c7183e5 ("serial: 8250: 8250_omap: Disable RX interrupt after DMA enable")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201111112653.2710-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enabling the lock dependency validator has revealed
that the way spinlocks are used in the IMX serial
port could result in a deadlock.
Specifically, imx_uart_int() acquires a spinlock
without disabling the interrupts, meaning that another
interrupt could come along and try to acquire the same
spinlock, potentially causing the two to wait for each
other indefinitely.
Use spin_lock_irqsave() instead to disable interrupts
upon acquisition of the spinlock.
Fixes: c974991d26 ("tty:serial:imx: use spin_lock instead of spin_lock_irqsave in isr")
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sam Nobs <samuel.nobs@taitradio.com>
Link: https://lore.kernel.org/r/1604955006-9363-1-git-send-email-samuel.nobs@taitradio.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This commit adds driver for the FPGA-based LiteUART serial controller
from LiteX SoC builder.
The current implementation supports LiteUART configured
for 32 bit data width and 8 bit CSR bus width.
It does not support IRQ.
Signed-off-by: Filip Kokosinski <fkokosinski@antmicro.com>
Signed-off-by: Mateusz Holenko <mholenko@antmicro.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stafford Horne <shorne@gmail.com>
Here are a small number of small tty and serial fixes for some reported
problems for the tty core, vt code, and some serial drivers.
They include fixes for:
- a buggy and obsolete vt font ioctl removal
- 8250_mtk serial baudrate runtime warnings
- imx serial earlycon build configuration fix
- txx9 serial driver error path cleanup issues
- tty core fix in release_tty that can be triggered by trying to
bind an invalid serial port name to a speakup console device
Almost all of these have been in linux-next without any problems, the
only one that hasn't, just deletes code :)
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX6g7nQ8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymmVACeNXgZpIAUJujtM7hQAEpCDYrFZ08An13TN07Y
wZe5okUITYIXQRZevKyi
=w0og
-----END PGP SIGNATURE-----
Merge tag 'tty-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a small number of small tty and serial fixes for some
reported problems for the tty core, vt code, and some serial drivers.
They include fixes for:
- a buggy and obsolete vt font ioctl removal
- 8250_mtk serial baudrate runtime warnings
- imx serial earlycon build configuration fix
- txx9 serial driver error path cleanup issues
- tty core fix in release_tty that can be triggered by trying to bind
an invalid serial port name to a speakup console device
Almost all of these have been in linux-next without any problems, the
only one that hasn't, just deletes code :)"
* tag 'tty-5.10-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
vt: Disable KD_FONT_OP_COPY
tty: fix crash in release_tty if tty->port is not set
serial: txx9: add missing platform_driver_unregister() on error in serial_txx9_init
tty: serial: imx: enable earlycon by default if IMX_SERIAL_CONSOLE is enabled
serial: 8250_mtk: Fix uart_get_baud_rate warning
It's buggy:
On Fri, Nov 06, 2020 at 10:30:08PM +0800, Minh Yuan wrote:
> We recently discovered a slab-out-of-bounds read in fbcon in the latest
> kernel ( v5.10-rc2 for now ). The root cause of this vulnerability is that
> "fbcon_do_set_font" did not handle "vc->vc_font.data" and
> "vc->vc_font.height" correctly, and the patch
> <https://lkml.org/lkml/2020/9/27/223> for VT_RESIZEX can't handle this
> issue.
>
> Specifically, we use KD_FONT_OP_SET to set a small font.data for tty6, and
> use KD_FONT_OP_SET again to set a large font.height for tty1. After that,
> we use KD_FONT_OP_COPY to assign tty6's vc_font.data to tty1's vc_font.data
> in "fbcon_do_set_font", while tty1 retains the original larger
> height. Obviously, this will cause an out-of-bounds read, because we can
> access a smaller vc_font.data with a larger vc_font.height.
Further there was only one user ever.
- Android's loadfont, busybox and console-tools only ever use OP_GET
and OP_SET
- fbset documentation only mentions the kernel cmdline font: option,
not anything else.
- systemd used OP_COPY before release 232 published in Nov 2016
Now unfortunately the crucial report seems to have gone down with
gmane, and the commit message doesn't say much. But the pull request
hints at OP_COPY being broken
https://github.com/systemd/systemd/pull/3651
So in other words, this never worked, and the only project which
foolishly every tried to use it, realized that rather quickly too.
Instead of trying to fix security issues here on dead code by adding
missing checks, fix the entire thing by removing the functionality.
Note that systemd code using the OP_COPY function ignored the return
value, so it doesn't matter what we're doing here really - just in
case a lone server somewhere happens to be extremely unlucky and
running an affected old version of systemd. The relevant code from
font_copy_to_all_vcs() in systemd was:
/* copy font from active VT, where the font was uploaded to */
cfo.op = KD_FONT_OP_COPY;
cfo.height = vcs.v_active-1; /* tty1 == index 0 */
(void) ioctl(vcfd, KDFONTOP, &cfo);
Note this just disables the ioctl, garbage collecting the now unused
callbacks is left for -next.
v2: Tetsuo found the old mail, which allowed me to find it on another
archive. Add the link too.
Acked-by: Peilin Ye <yepeilin.cs@gmail.com>
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
References: https://lists.freedesktop.org/archives/systemd-devel/2016-June/036935.html
References: https://github.com/systemd/systemd/pull/3651
Cc: Greg KH <greg@kroah.com>
Cc: Peilin Ye <yepeilin.cs@gmail.com>
Cc: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp>
Signed-off-by: Daniel Vetter <daniel.vetter@intel.com>
Link: https://lore.kernel.org/r/20201108153806.3140315-1-daniel.vetter@ffwll.ch
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 2ae0b31e0f ("tty: don't crash in tty_init_dev when missing
tty_port") didn't fully prevent the crash as the cleanup path in
tty_init_dev() calls release_tty() which dereferences tty->port
without checking it for non-null.
Add tty->port checks to release_tty to avoid the kernel crash.
Fixes: 2ae0b31e0f ("tty: don't crash in tty_init_dev when missing tty_port")
Signed-off-by: Matthias Reichl <hias@horus.com>
Link: https://lore.kernel.org/r/20201105123432.4448-1-hias@horus.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add the missing platform_driver_unregister() before return
from serial_txx9_init in the error handling case when failed
to register serial_txx9_pci_driver with macro ENABLE_SERIAL_TXX9_PCI
defined.
Fixes: ab4382d274 ("tty: move drivers/serial/ to drivers/tty/serial/")
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20201103084942.109076-1-miaoqinglang@huawei.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since 699cc4dfd1 (tty: serial: imx: add imx earlycon driver), the earlycon
part of imx serial is a separate driver and isn't necessarily enabled anymore
when the console is enabled. This causes users to loose the earlycon
functionality when upgrading their kenrel configuration via oldconfig.
Enable earlycon by default when IMX_SERIAL_CONSOLE is enabled.
Fixes: 699cc4dfd1 (tty: serial: imx: add imx earlycon driver)
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20201105204026.1818219-1-l.stach@pengutronix.de
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Mediatek 8250 port supports speed higher than uartclk / 16. If the baud
rates in both the new and the old termios setting are higher than
uartclk / 16, the WARN_ON in uart_get_baud_rate() will be triggered.
Passing NULL as the old termios so uart_get_baud_rate() will use
uartclk / 16 - 1 as the new baud rate which will be replaced by the
original baud rate later by tty_termios_encode_baud_rate() in
mtk8250_set_termios().
Fixes: 551e553f0d ("serial: 8250_mtk: Fix high-speed baud rates clamping")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Link: https://lore.kernel.org/r/20201102120749.374458-1-tientzu@chromium.org
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The only usage of msm_uart_pops is to assign its address to the ops
field in the uart_port struct, which is a pointer to const. Make it
const to allow the compiler to put it in read-only memory.
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201104235134.17793-1-rikard.falkeborn@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
UARTs on TI SoCs prior to J7200 don't provide independent control over
RX FIFO not empty interrupt (RHR_IT) and RX timeout interrupt.
Starting with J7200 SoC, its possible to disable RHR_IT independent of
RX timeout interrupt using bit 2 of IER2 register. So disable RHR_IT
once RX DMA is started so as to avoid spurious interrupt being raised
when data is in the RX FIFO but is yet to be drained by DMA (a known
errata in older SoCs).
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20201029051930.7097-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
drivers/tty/serial/serial_mctrl_gpio.c:214
mctrl_gpio_init() warn: passing zero to 'ERR_PTR'
gpiod_to_irq() never return 0, so remove the useless test
and make code more clear.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Link: https://lore.kernel.org/r/20201031030530.1304-1-yuehaibing@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A note from the vendor:
"The hardware used with synclink.c and synclinkmp.c has not been
manufactured for 15 years and was low volume. The chances of either
driver still being in use is very low. Not even Microgate (me) has
the ability to test either anymore (no hardware). I don’t know the
policy about driver removal, but I think both could be removed
without upsetting anyone."
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201105123357.708813-3-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A note from the vendor:
"The hardware used with synclink.c and synclinkmp.c has not been
manufactured for 15 years and was low volume. The chances of either
driver still being in use is very low. Not even Microgate (me) has
the ability to test either anymore (no hardware). I don’t know the
policy about driver removal, but I think both could be removed
without upsetting anyone."
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201105123357.708813-2-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/synclink.c:7708: warning: Function parameter or member 'txqueue' not described in 'hdlcdev_tx_timeout'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: paulkf@microgate.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-37-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'fifo_mode_enable_status' not described in 'tegra_uart_chip_data'
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'uart_max_port' not described in 'tegra_uart_chip_data'
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'max_dma_burst_bytes' not described in 'tegra_uart_chip_data'
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'error_tolerance_low_range' not described in 'tegra_uart_chip_data'
drivers/tty/serial/serial-tegra.c:94: warning: Function parameter or member 'error_tolerance_high_range' not described in 'tegra_uart_chip_data'
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: "Christian König" <christian.koenig@amd.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-tegra@vger.kernel.org
Cc: linux-media@vger.kernel.org
Cc: dri-devel@lists.freedesktop.org
Cc: linaro-mm-sig@lists.linaro.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-31-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_ldisc.c:160: warning: Function parameter or member 'tty' not described in 'tty_ldisc_get'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-30-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/stm32-usart.c: In function ‘stm32_transmit_chars_dma’:
drivers/tty/serial/stm32-usart.c:353:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
drivers/tty/serial/stm32-usart.c: In function ‘stm32_of_dma_rx_probe’:
drivers/tty/serial/stm32-usart.c:1090:15: warning: variable ‘cookie’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Gerald Baeza <gerald.baeza@st.com>
Cc: linux-serial@vger.kernel.org
Cc: linux-stm32@st-md-mailman.stormreply.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-29-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/synclinkmp.c:1808: warning: Function parameter or member 'txqueue' not described in 'hdlcdev_tx_timeout'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: paulkf@microgate.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-27-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/synclink_gt.c:633: warning: Function parameter or member 'tty' not described in 'ldisc_receive_buf'
drivers/tty/synclink_gt.c:633: warning: Function parameter or member 'data' not described in 'ldisc_receive_buf'
drivers/tty/synclink_gt.c:633: warning: Function parameter or member 'flags' not described in 'ldisc_receive_buf'
drivers/tty/synclink_gt.c:633: warning: Function parameter or member 'count' not described in 'ldisc_receive_buf'
drivers/tty/synclink_gt.c:1683: warning: Function parameter or member 'txqueue' not described in 'hdlcdev_tx_timeout'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: paulkf@microgate.com
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-24-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/xilinx_uartps.c:205: warning: Function parameter or member 'cts_override' not described in 'cdns_uart'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-23-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/ifx6x60.c:553: warning: Function parameter or member 'tty' not described in 'ifx_port_activate'
drivers/tty/serial/ifx6x60.c:728: warning: Function parameter or member 't' not described in 'ifx_spi_io'
drivers/tty/serial/ifx6x60.c:728: warning: Excess function parameter 'data' description in 'ifx_spi_io'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Filip Aben <f.aben@option.com>
Cc: Joseph Barrow <d.barow@option.com>
Cc: Jan Dumon <j.dumon@option.com>
Cc: Russ Gorby <russ.gorby@intel.com>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-22-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/msm_serial.c: In function ‘msm_complete_tx_dma’:
drivers/tty/serial/msm_serial.c:429:18: warning: variable ‘status’ set but not used [-Wunused-but-set-variable]
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Robert Love <rlove@google.com>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lore.kernel.org/r/20201104193549.4026187-21-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/lpc32xx_hs.c: In function ‘__serial_uart_flush’:
drivers/tty/serial/lpc32xx_hs.c:244:6: warning: variable ‘tmp’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Sylvain Lemieux <slemieux.tyco@gmail.com>
Cc: Kevin Wells <kevin.wells@nxp.com>
Cc: Roland Stigge <stigge@antcom.de>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Link: https://lore.kernel.org/r/20201104193549.4026187-20-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/n_gsm.c:85: warning: Function parameter or member 'ref' not described in 'gsm_mux_net'
drivers/tty/n_gsm.c:85: warning: Function parameter or member 'dlci' not described in 'gsm_mux_net'
drivers/tty/n_gsm.c:664: warning: Function parameter or member 'dlci' not described in 'gsm_data_kick'
drivers/tty/n_gsm.c:1015: warning: Function parameter or member 'clen' not described in 'gsm_process_modem'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-19-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When !ACPI 'sbsa_uart_acpi_match' is not referenced.
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/amba-pl011.c:2792:36: warning: ‘sbsa_uart_acpi_match’ defined but not used [-Wunused-const-variable=]
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-18-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/pty.c:710: warning: Function parameter or member 'file' not described in 'ptm_unix98_lookup'
drivers/tty/pty.c:726: warning: Function parameter or member 'file' not described in 'pts_unix98_lookup'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: "C. Scott Ananian" <cananian@alumni.princeton.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-17-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_audit.c:91: warning: Function parameter or member 'buf' not described in 'tty_audit_buf_push'
drivers/tty/tty_audit.c:129: warning: Function parameter or member 'sig' not described in 'tty_audit_fork'
drivers/tty/tty_audit.c:137: warning: Function parameter or member 'tty' not described in 'tty_audit_tiocsti'
drivers/tty/tty_audit.c:137: warning: Function parameter or member 'ch' not described in 'tty_audit_tiocsti'
drivers/tty/tty_audit.c:202: warning: Function parameter or member 'tty' not described in 'tty_audit_add_data'
drivers/tty/tty_audit.c:202: warning: Function parameter or member 'data' not described in 'tty_audit_add_data'
drivers/tty/tty_audit.c:202: warning: Function parameter or member 'size' not described in 'tty_audit_add_data'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Miloslav Trmac <mitr@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-16-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/8250/serial_cs.c: In function ‘multi_config’:
drivers/tty/serial/8250/serial_cs.c:562:7: warning: variable ‘err’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: "David A. Hinds" <dahinds@users.sourceforge.net>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-15-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Demote non-conformant headers and supply some missing descriptions.
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_io.c:218: warning: Function parameter or member 'file' not described in 'tty_free_file'
drivers/tty/tty_io.c:566: warning: Function parameter or member 'exit_session' not described in '__tty_hangup'
drivers/tty/tty_io.c:1077: warning: Function parameter or member 'tty' not described in 'tty_send_xchar'
drivers/tty/tty_io.c:1077: warning: Function parameter or member 'ch' not described in 'tty_send_xchar'
drivers/tty/tty_io.c:1155: warning: Function parameter or member 'file' not described in 'tty_driver_lookup_tty'
drivers/tty/tty_io.c:1508: warning: Function parameter or member 'tty' not described in 'release_tty'
drivers/tty/tty_io.c:1508: warning: Function parameter or member 'idx' not described in 'release_tty'
drivers/tty/tty_io.c:2973: warning: Function parameter or member 'driver' not described in 'alloc_tty_struct'
drivers/tty/tty_io.c:2973: warning: Function parameter or member 'idx' not described in 'alloc_tty_struct'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Nick Holloway <alfie@dcs.warwick.ac.uk>
Cc: -- <julian@uhunix.uhcc.hawaii.edu>
Cc: Marko Kohtala <Marko.Kohtala@hut.fi>
Cc: Bill Hawes <whawes@star.net>
Cc: "C. Scott Ananian" <cananian@alumni.princeton.edu>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Andrew Morton <andrewm@uow.edu.eu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-13-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serial/jsm/jsm_cls.c: In function ‘cls_copy_data_from_uart_to_queue’:
drivers/tty/serial/jsm/jsm_cls.c:400:7: warning: variable ‘discard’ set but not used [-Wunused-but-set-variable]
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-12-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/n_tty.c:405: warning: Function parameter or member 'tty' not described in 'is_continuation'
drivers/tty/n_tty.c:1701: warning: Function parameter or member 'flow' not described in 'n_tty_receive_buf_common'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: "Andrew J. Kroll" <ag784@freenet.buffalo.edu>
Cc: processes-Sapan Bhatia <sapan@corewars.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-11-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/vt/consolemap.c:739: warning: Function parameter or member 'ct' not described in 'con_get_unimap'
drivers/tty/vt/consolemap.c:739: warning: Function parameter or member 'uct' not described in 'con_get_unimap'
drivers/tty/vt/consolemap.c:739: warning: Function parameter or member 'list' not described in 'con_get_unimap'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Jakub Jelinek <jj@ultra.linux.cz>
Cc: Stanislav Voronyi <stas@cnti.uanet.kharkov.ua>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-10-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_jobctrl.c:32: warning: Function parameter or member 'sig' not described in '__tty_check_change'
drivers/tty/tty_jobctrl.c:95: warning: Function parameter or member 'tty' not described in '__proc_set_tty'
drivers/tty/tty_jobctrl.c:344: warning: Function parameter or member 'file' not described in 'tiocsctty'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-8-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_port.c:633: warning: Function parameter or member 'port' not described in 'tty_port_close'
drivers/tty/tty_port.c:633: warning: Function parameter or member 'tty' not described in 'tty_port_close'
drivers/tty/tty_port.c:633: warning: Function parameter or member 'filp' not described in 'tty_port_close'
drivers/tty/tty_port.c:672: warning: Function parameter or member 'port' not described in 'tty_port_open'
drivers/tty/tty_port.c:672: warning: Function parameter or member 'tty' not described in 'tty_port_open'
drivers/tty/tty_port.c:672: warning: Function parameter or member 'filp' not described in 'tty_port_open'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-7-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_buffer.c:592: warning: Function parameter or member 'limit' not described in 'tty_buffer_set_limit'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-6-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/tty_baudrate.c:234: warning: Function parameter or member 'tty' not described in 'tty_encode_baud_rate'
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-4-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following W=1 kernel build warning(s):
drivers/tty/serdev/core.c: In function ‘serdev_controller_remove’:
drivers/tty/serdev/core.c:811: warning: Function parameter or member 'owner' not described in '__serdev_device_driver_register'
Cc: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-3-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No need to have a dummy variable here.
Fixes the following W=1 kernel build warning(s):
drivers/tty/serdev/core.c: In function ‘serdev_controller_remove’:
drivers/tty/serdev/core.c:791:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable]
Cc: Rob Herring <robh@kernel.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201104193549.4026187-2-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
'puts_queue' currently loops over characters and employs the full tty
buffer machinery for every character. Do the buffer allocation only once
and copy all the character at once. This is achieved using
tty_insert_flip_string instead of loop+tty_insert_flip_char.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-17-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of a 'for' loop with 'test_bit's to find a bit in a range, use
find_next_bit to achieve the same in a simpler and faster manner.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Instead of a multiline macro, convert HW_RAW to an inline function. It
allows for type checking of the parameter. And given we split the code
into two tests, it is now more readable too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-15-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do the permission check on a single place. That is where perm is
really checked.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-14-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Setting of function key strings is now very complex. It uses a global
buffer 'func_buf' which is prefilled in defkeymap.c_shipped. Then there
is also an index table called 'func_table'. So initially, we have
something like this:
char func_buf[] = "\e[[A\0" // for F1
"\e[[B\0" // for F2
...;
char *func_table[] = {
func_buf + 0, // for F1
func_buf + 5, // for F2
... }
When a user changes some specific func string by KDSKBSENT, it is
changed in 'func_buf'. If it is shorter or equal to the current one, it
is handled by a very quick 'strcpy'.
When the user's string is longer, the whole 'func_buf' is reallocated to
allow expansion somewhere in the middle. The buffer before the user's
string is copied, the user's string appended and the rest appended too.
Now, the index table (func_table) needs to be recomputed, of course.
One more complication is the held spinlock -- we have to unlock,
reallocate, lock again and do the whole thing again to be sure noone
raced with us.
In this patch, we chose completely orthogonal approach: when the user's
string is longer than the current one, we simply assign the 'kstrdup'ed
copy to the index table (func_table) and modify func_buf in no way. We
only need to make sure we free the old entries. So we need a bitmap
is_kmalloc and free the old entries (but not the original func_buf
rodata string).
Also note that we do not waste so much space as previous approach. We
only allocate space for single entries which are longer, while before,
the whole buffer was duplicated plus space for the longer string.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
KDGKBSENT (the getter) needs only 'user_kdgkb->kb_func' from the
userspace, i.e. the index. Then it needs a buffer for a local copy of
'kb_string'.
KDSKBSENT (the setter) needs a copy up to the length of
'user_kdgkb->kb_string'.
That means, we obtain the index before the switch-case and use it in
both paths and:
1) allocate full space in the getter case, and
2) copy the string only in the setter case. We do it by strndup_user
helper now which was not available when this function was written.
Given we copy the two members of 'struct kbsentry' separately, we no
longer need a local definition. Hence we need to change all the sizeofs
here too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are too many one-letter variables in vt_do_kdgkb_ioctl which is
rather confusing. Rename 'i' to 'kb_func' and change its type to be the
same as its originating value (struct kbsentry.kb_func) -- unsigned
char.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
key_down is sued as a bitmap using test_bit, set_bit and similar.
So declare it using DECLARE_BITMAP to make it obvious even from the
declaration.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do the permission check on a single place. That is where perm is really
checked.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split vt_do_kdsk_ioctl into three functions:
* getter (KDGKBENT/vt_kdgkbent)
* setter (KDSKBENT/vt_kdskbent)
* switch-case helper (vt_do_kdsk_ioctl)
This eliminates the need of ugly one-letter macros as we use parameters
now:
* i aka tmp.kb_index -> idx
* s aka tmp.kb_table -> map
* v aka tmp.kb_value -> val
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Define one limit per line and index them by their index, so that it is
clear what is what.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are many includes and it is hard to check if something is there or
not. So sort them alphabetically.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We use spin locks, but don't include linux/spinlock.h in keyboards.c. So
fix this up.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ctrl_alt_del is already declared in linux/reboot.h which we include. So
remove this second (superfluous) declaration.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201029113222.32640-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some of the font tty ioctl's always used the current foreground VC for
their operations. Don't do that then.
This fixes a data race on fg_console.
Side note: both Michael Ellerman and Jiri Slaby point out that all these
ioctls are deprecated, and should probably have been removed long ago,
and everything seems to be using the KDFONTOP ioctl instead.
In fact, Michael points out that it looks like busybox's loadfont
program seems to have switched over to using KDFONTOP exactly _because_
of this bug (ahem.. 12 years ago ;-).
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
Acked-by: Michael Ellerman <mpe@ellerman.id.au>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 5ba1278787, we shuffled with the check of 'perm'. But my
brain somehow inverted the condition in 'do_unimap_ioctl' (I thought
it is ||, not &&), so GIO_UNIMAP stopped working completely.
Move the 'perm' checks back to do_unimap_ioctl and do them right again.
In fact, this reverts this part of code to the pre-5ba127878722 state.
Except 'perm' is now a bool.
Fixes: 5ba1278787 ("vt_ioctl: move perm checks level up")
Cc: stable@vger.kernel.org
Reported-by: Fabian Vogt <fvogt@suse.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201026055419.30518-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both read-side users of func_table/func_buf need locking. Without that,
one can easily confuse the code by repeatedly setting altering strings
like:
while (1)
for (a = 0; a < 2; a++) {
struct kbsentry kbs = {};
strcpy((char *)kbs.kb_string, a ? ".\n" : "88888\n");
ioctl(fd, KDSKBSENT, &kbs);
}
When that program runs, one can get unexpected output by holding F1
(note the unxpected period on the last line):
.
88888
.8888
So protect all accesses to 'func_table' (and func_buf) by preexisting
'func_buf_lock'.
It is easy in 'k_fn' handler as 'puts_queue' is expected not to sleep.
On the other hand, KDGKBSENT needs a local (atomic) copy of the string
because copy_to_user can sleep. Use already allocated, but unused
'kbs->kb_string' for that purpose.
Note that the program above needs at least CAP_SYS_TTY_CONFIG.
This depends on the previous patch and on the func_buf_lock lock added
in commit 46ca3f735f (tty/vt: fix write/write race in ioctl(KDSKBSENT)
handler) in 5.2.
Likely fixes CVE-2020-25656.
Cc: <stable@vger.kernel.org>
Reported-by: Minh Yuan <yuanmingbuaa@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201019085517.10176-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use 'strlen' of the string, add one for NUL terminator and simply do
'copy_to_user' instead of the explicit 'for' loop. This makes the
KDGKBSENT case more compact.
The only thing we need to take care about is NULL 'func_table[i]'. Use
an empty string in that case.
The original check for overflow could never trigger as the func_buf
strings are always shorter or equal to 'struct kbsentry's.
Cc: <stable@vger.kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20201019085517.10176-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Prior to the commit that this one fixes, the FIFO size was derived from
the read-only register LPUARTx_FIFO[TXFIFOSIZE] using the following
formula:
TX FIFO size = 2 ^ (LPUARTx_FIFO[TXFIFOSIZE] - 1)
The documentation for LS1021A is a mess. Under chapter 26.1.3 LS1021A
LPUART module special consideration, it mentions TXFIFO_SZ and RXFIFO_SZ
being equal to 4, and in the register description for LPUARTx_FIFO, it
shows the out-of-reset value of TXFIFOSIZE and RXFIFOSIZE fields as "011",
even though these registers read as "101" in reality.
And when LPUART on LS1021A was working, the "101" value did correspond
to "16 datawords", by applying the formula above, even though the
documentation is wrong again (!!!!) and says that "101" means 64 datawords
(hint: it doesn't).
So the "new" formula created by commit f77ebb241c has all the premises
of being wrong for LS1021A, because it relied only on false data and no
actual experimentation.
Interestingly, in commit c2f448cff2 ("tty: serial: fsl_lpuart: add
LS1028A support"), Michael Walle applied a workaround to this by manually
setting the FIFO widths for LS1028A. It looks like the same values are
used by LS1021A as well, in fact.
When the driver thinks that it has a deeper FIFO than it really has,
getty (user space) output gets truncated.
Many thanks to Michael for pointing out where to look.
Fixes: f77ebb241c ("tty: serial: fsl_lpuart: correct the FIFO depth size")
Suggested-by: Michael Walle <michael@walle.cc>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20201023013429.3551026-1-vladimir.oltean@nxp.com
Reviewed-by：Fugang Duan <fugang.duan@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 293f899594 ("tty: serial: 21285: stop using the unused[]
variable from struct uart_port") introduced a bug which stops the
transmit interrupt being disabled when there are no characters to
transmit - disabling the transmit interrupt at the interrupt controller
is the only way to stop an interrupt storm. If this interrupt is not
disabled when there are no transmit characters, we end up with an
interrupt storm which prevents the machine making forward progress.
Fixes: 293f899594 ("tty: serial: 21285: stop using the unused[] variable from struct uart_port")
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/E1kU4GS-0006lE-OO@rmk-PC.armlinux.org.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Simplify the code which fetches the input clock by using
devm_clk_get_optional(). If no input clock is present
devm_clk_get_optional() will return NULL instead of an error
which matches the behavior of the old code.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201007084635.594991-2-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Device property API allows to gather device resources from different sources,
such as ACPI. Convert the drivers to unleash the power of device property API.
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20201007084635.594991-1-andy.shevchenko@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
SoC changes, a substantial part of this is cleanup of some of the older
platforms that used to have a bunch of board files. In particular:
- Removal of non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP platforms,
moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
THere are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones re:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP
-----BEGIN PGP SIGNATURE-----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=0+Ee
-----END PGP SIGNATURE-----
Merge tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC platform updates from Olof Johansson:
"SoC changes, a substantial part of this is cleanup of some of the
older platforms that used to have a bunch of board files.
In particular:
- Remove non-DT i.MX platforms that haven't seen activity in years,
it's time to remove them.
- A bunch of cleanup and removal of platform data for TI/OMAP
platforms, moving over to genpd for power/reset control (yay!)
- Major cleanup of Samsung S3C24xx and S3C64xx platforms, moving them
closer to multiplatform support (not quite there yet, but getting
close).
There are a few other changes too, smaller fixlets, etc. For new
platform support, the primary ones are:
- New SoC: Hisilicon SD5203, ARM926EJ-S platform.
- Cpufreq support for i.MX7ULP"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (121 commits)
ARM: mstar: Select MStar intc
ARM: stm32: Replace HTTP links with HTTPS ones
ARM: debug: add UART early console support for SD5203
ARM: hisi: add support for SD5203 SoC
ARM: omap3: enable off mode automatically
clk: imx: imx35: Remove mx35_clocks_init()
clk: imx: imx31: Remove mx31_clocks_init()
clk: imx: imx27: Remove mx27_clocks_init()
ARM: imx: Remove unused definitions
ARM: imx35: Retrieve the IIM base address from devicetree
ARM: imx3: Retrieve the AVIC base address from devicetree
ARM: imx3: Retrieve the CCM base address from devicetree
ARM: imx31: Retrieve the IIM base address from devicetree
ARM: imx27: Retrieve the CCM base address from devicetree
ARM: imx27: Retrieve the SYSCTRL base address from devicetree
ARM: s3c64xx: bring back notes from removed debug-macro.S
ARM: s3c24xx: fix Wunused-variable warning on !MMU
ARM: samsung: fix PM debug build with DEBUG_LL but !MMU
MAINTAINERS: mark linux-samsung-soc list non-moderated
ARM: imx: Remove remnant board file support pieces
...
- removed support for PNX833x alias NXT_STB22x
- included Ingenic SoC support into generic MIPS kernels
- added support for new Ingenic SoCs
- converted workaround selection to use Kconfig
- replaced old boot mem functions by memblock_*
- enabled COP2 usage in kernel for Loongson64 to make usage
of usage of 16byte load/stores possible
- cleanups and fixes
-----BEGIN PGP SIGNATURE-----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=Aa/Q
-----END PGP SIGNATURE-----
Merge tag 'mips_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Thomas Bogendoerfer:
- removed support for PNX833x alias NXT_STB22x
- included Ingenic SoC support into generic MIPS kernels
- added support for new Ingenic SoCs
- converted workaround selection to use Kconfig
- replaced old boot mem functions by memblock_*
- enabled COP2 usage in kernel for Loongson64 to make use
of 16byte load/stores possible
- cleanups and fixes
* tag 'mips_5.10' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (92 commits)
MIPS: DEC: Restore bootmem reservation for firmware working memory area
MIPS: dec: fix section mismatch
bcm963xx_tag.h: fix duplicated word
mips: ralink: enable zboot support
MIPS: ingenic: Remove CPU_SUPPORTS_HUGEPAGES
MIPS: cpu-probe: remove MIPS_CPU_BP_GHIST option bit
MIPS: cpu-probe: introduce exclusive R3k CPU probe
MIPS: cpu-probe: move fpu probing/handling into its own file
MIPS: replace add_memory_region with memblock
MIPS: Loongson64: Clean up numa.c
MIPS: Loongson64: Select SMP in Kconfig to avoid build error
mips: octeon: Add Ubiquiti E200 and E220 boards
MIPS: SGI-IP28: disable use of ll/sc in kernel
MIPS: tx49xx: move tx4939_add_memory_regions into only user
MIPS: pgtable: Remove used PAGE_USERIO define
MIPS: alchemy: Share prom_init implementation
MIPS: alchemy: Fix build breakage, if TOUCHSCREEN_WM97XX is disabled
MIPS: process: include exec.h header in process.c
MIPS: process: Add prototype for function arch_dup_task_struct
MIPS: idle: Add prototype for function check_wait
...
After some unsuccessful attempts to use sysrq over console, figured
out that port->has_sysrq should likely be enabled, as per other
architectures, this when CONFIG_SERIAL_MCF_CONSOLE is also enabled.
Tested some magic sysrq commands (h, p, t, b), they works now
properly. Commands works inside 5 secs after BREAK is sent, as
expected.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20201002140545.477481-1-angelo.dureghello@timesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add handling of magic sysrq keys when using dma/edma.
Tested by sending BREAK followed by a sysrq command inside
a 5 secs time window, by:
echo 1 > /proc/sys/kernel/sysrq
BREAK + h, t, e, b, c
Tested also sending a command after 5 secs after BREAK, that's
properly ignored.
Signed-off-by: Angelo Dureghello <angelo.dureghello@timesys.com>
Link: https://lore.kernel.org/r/20201004161144.1307174-1-angelo.dureghello@timesys.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
All slots in sysrq_key_table[] are either used, reserved or at least
commented with their intended use. This patch adds capital letter versions
available, which means adding 26 more entries.
For already existing SysRq operations the user presses Alt-SysRq-<key>, and
for the newly added ones Alt-Shift-SysRq-<key>.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20200818112825.6445-2-andrzej.p@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently, the RX interrupt logic uses the RXEMPTY interrupt, with the
RXEMPTYINV bit set, which means we get an RX interrupt as soon as the
RX FIFO is non-empty.
However, with the MAX310X having a FIFO of 128 bytes, this makes very
poor use of the FIFO: we trigger an interrupt as soon as the RX FIFO
has one byte, which means a lot of interrupts, each only collecting a
few bytes from the FIFO, causing a significant CPU load.
Instead this commit relies on two other RX interrupt events:
- MAX310X_IRQ_RXFIFO_BIT, which triggers when the RX FIFO has reached
a certain threshold, which we define to be half of the FIFO
size. This ensure we get an interrupt before the RX FIFO fills up.
- MAX310X_LSR_RXTO_BIT, which triggers when the RX FIFO has received
some bytes, and then no more bytes are received for a certain
time. Arbitrarily, this time is defined to the time is takes to
receive 4 characters.
On a Microchip SAMA5D3 platform that is receiving 20 bytes every 16ms
over one MAX310X UART, this patch has allowed to reduce the CPU
consumption of the interrupt handler thread from ~25% to 6-7%.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com>
Link: https://lore.kernel.org/r/20201001074415.349739-1-thomas.petazzoni@bootlin.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been discovered that there is a potential deadlock between
the clock-change-notifier thread and the UART port suspending one:
CPU0 (suspend CPU/UART) CPU1 (update clock)
---- ----
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
lock(&port->mutex);
lock((work_completion)(&data->clk_work));
*** DEADLOCK ***
The best way to fix this is to eliminate the CPU0
port->mutex/work-completion scenario. So we suggest to register and
unregister the clock-notifier during the DW APB UART port probe/remove
procedures, instead of doing that at the points of the port
startup/shutdown.
Link: https://lore.kernel.org/linux-serial/f1cd5c75-9cda-6896-a4e2-42c5bfc3f5c3@redhat.com
Fixes: cc816969d7 ("serial: 8250_dw: Fix common clocks usage race condition")
Reported-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is erroneous to update the TTY port baud rate if it hasn't been
initialized yet, because in that case the TTY struct isn't set. So there
is no termios structure to get and re-calculate the baud if the current
baud can't be reached. Let's skip the baud rate update then until the port
is fully initialized.
Note the update UART clock method still sets the uartclk member with a new
ref clock value even if the port is turned off. The new UART ref clock
rate will be used later on the port starting up procedure.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It has been a mistake to add the MCR register RTS/DTS fields setting in
the generic method of the UART reference clock update. There is no point
in asserting these lines at that procedure. Just discard the
serial8250_out_MCR() mathod invocation from there then.
Fixes: 868f3ee6e4 ("serial: 8250: Add 8250 port clock update method")
Tested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200923161950.6237-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The IPG clock is disabled at the end of imx_uart_shutdown(); we really
don't want to run any IRQ handlers after this point.
At least on i.MX8MN, the UART will happily continue to generate interrupts
even with its clocks disabled, but in this state, all register writes are
ignored (which will cause the shadow registers to differ from the actual
register values, resulting in all kinds of weirdness).
In a transfer without DMA, this could lead to the following sequence of
events:
- The UART finishes its transmission while imx_uart_shutdown() is run,
triggering the TXDC interrupt (we can trigger this fairly reliably by
writing a single byte to the TTY and closing it right away)
- imx_uart_shutdown() finishes, disabling the UART clocks
- imx_uart_int() -> imx_uart_transmit_buffer() -> imx_uart_stop_tx()
imx_uart_stop_tx() should now clear UCR4_TCEN to disable the TXDC
interrupt, but this register write is ineffective. This results in an
interrupt storm.
To disable all interrupts in the same place, and to avoid setting UCR4
twice, clearing UCR4_OREN is moved below del_timer_sync() as well; this
should be harmless.
Signed-off-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Link: https://lore.kernel.org/r/20200925082412.12960-1-matthias.schiffer@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the port of the commit db1b5bc047 ("serial: 8250: Fix TX
interrupt handling condition") to the 8250_fsl irq handling logic.
Interrupt handler checked THRE bit (transmitter holding register
empty) in LSR to detect if TX fifo is empty.
In case when there is only receive interrupts the TX handling
got called because THRE bit in LSR is set when there is no
transmission (FIFO empty). TX handling caused TX stop, which in
RS-485 half-duplex mode actually resets receiver FIFO. This is not
desired during reception because of possible data loss.
The fix is to check if THRI is set in IER in addition of the TX
fifo status. THRI in IER is set when TX is started and cleared
when TX is stopped.
This ensures that TX handling is only called when there is really
transmission on going and an interrupt for THRE and not when there
are only RX interrupts.
Signed-off-by: Andrij Abyzov <aabyzov@slb.com>
Link: https://lore.kernel.org/r/20200928144127.87156-1-aabyzov@slb.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Issuing a magic-sysrq via the PL011 causes the following lockdep splat,
which is easily reproducible under QEMU:
| sysrq: Changing Loglevel
| sysrq: Loglevel set to 9
|
| ======================================================
| WARNING: possible circular locking dependency detected
| 5.9.0-rc7 #1 Not tainted
| ------------------------------------------------------
| systemd-journal/138 is trying to acquire lock:
| ffffab133ad950c0 (console_owner){-.-.}-{0:0}, at: console_lock_spinning_enable+0x34/0x70
|
| but task is already holding lock:
| ffff0001fd47b098 (&port_lock_key){-.-.}-{2:2}, at: pl011_int+0x40/0x488
|
| which lock already depends on the new lock.
[...]
| Possible unsafe locking scenario:
|
| CPU0 CPU1
| ---- ----
| lock(&port_lock_key);
| lock(console_owner);
| lock(&port_lock_key);
| lock(console_owner);
|
| *** DEADLOCK ***
The issue being that CPU0 takes 'port_lock' on the irq path in pl011_int()
before taking 'console_owner' on the printk() path, whereas CPU1 takes
the two locks in the opposite order on the printk() path due to setting
the "console_owner" prior to calling into into the actual console driver.
Fix this in the same way as the msm-serial driver by dropping 'port_lock'
before handling the sysrq.
Cc: <stable@vger.kernel.org> # 4.19+
Cc: Russell King <linux@armlinux.org.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20200811101313.GA6970@willie-the-truck
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Tested-by: Will Deacon <will@kernel.org>
Signed-off-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20200930120432.16551-1-will@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The watermark is set to 1, so we need to input two chars to trigger RDRF
using the original logic. With the new logic, we could always get the
char when there is data in FIFO.
Suggested-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929095509.21680-1-peng.fan@nxp.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The 2nd and 3rd parameter were wrongly used, and cause kernel abort when
doing kgdb debug.
Fixes: 1da17d7cf8 ("tty: serial: fsl_lpuart: Use appropriate lpuart32_* I/O funcs")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/20200929091920.22612-1-peng.fan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For QUP IP versions 2.5 and above the oversampling rate is
halved from 32 to 16.
Commit ce73460054 ("tty: serial: qcom_geni_serial: Update
the oversampling rate") is pushed to handle this scenario.
But the existing logic is failing to classify QUP Version 3.0
into the correct group ( 2.5 and above).
As result Serial Engine clocks are not configured properly for
baud rate and garbage data is sampled to FIFOs from the line.
So, fix the logic to detect QUP with versions 2.5 and above.
Fixes: ce73460054 ("tty: serial: qcom_geni_serial: Update the oversampling rate")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Paras Sharma <parashar@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/1601445926-23673-1-git-send-email-parashar@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a warning shows that 'ret' becomes an unused variable
after simplify the return expression of mvebu_uart_probe(). So
remove it.
Fixes: b63537020d ("serial: mvebu-uart: simplify the return expression of mvebu_uart_probe()")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Qinglang Miao <miaoqinglang@huawei.com>
Link: https://lore.kernel.org/r/20200929085651.158283-1-miaoqinglang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting UAF/OOB read at bit_putcs()/soft_cursor() [1][2], for
vt_resizex() from ioctl(VT_RESIZEX) allows setting font height larger than
actual font height calculated by con_font_set() from ioctl(PIO_FONT).
Since fbcon_set_font() from con_font_set() allocates minimal amount of
memory based on actual font height calculated by con_font_set(),
use of vt_resizex() can cause UAF/OOB read for font data.
VT_RESIZEX was introduced in Linux 1.3.3, but it is unclear that what
comes to the "+ more" part, and I couldn't find a user of VT_RESIZEX.
#define VT_RESIZE 0x5609 /* set kernel's idea of screensize */
#define VT_RESIZEX 0x560A /* set kernel's idea of screensize + more */
So far we are not aware of syzbot reports caused by setting non-zero value
to v_vlin parameter. But given that it is possible that nobody is using
VT_RESIZEX, we can try removing support for v_clin and v_vlin parameters.
Therefore, this patch effectively makes VT_RESIZEX behave like VT_RESIZE,
with emitting a message if somebody is still using v_clin and/or v_vlin
parameters.
[1] https://syzkaller.appspot.com/bug?id=32577e96d88447ded2d3b76d71254fb855245837
[2] https://syzkaller.appspot.com/bug?id=6b8355d27b2b94fb5cedf4655e3a59162d9e48e3
Reported-by: syzbot <syzbot+b308f5fd049fbbc6e74f@syzkaller.appspotmail.com>
Reported-by: syzbot <syzbot+16469b5e8e5a72e9131e@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/4933b81b-9b1a-355b-df0e-9b31e8280ab9@i-love.sakura.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
aarch64-linux-gnu-ld: drivers/tty/serial/imx_earlycon.o: in function `imx_uart_console_early_write':
imx_earlycon.c:(.text+0x84): undefined reference to `uart_console_write'
The driver uses the uart_console_write(), but SERIAL_CORE_CONSOLE is not
selected, so uart_console_write is not defined, then we get the error.
Fix this by selecting SERIAL_CORE_CONSOLE.
Fixes: 699cc4dfd1 ("tty: serial: imx: add imx earlycon driver")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20200919063240.2754965-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
aarch64-linux-gnu-ld: drivers/tty/hvc/hvc_dcc.o: in function `dcc_early_write':
hvc_dcc.c:(.text+0x164): undefined reference to `uart_console_write'
The driver uses the uart_console_write(), but SERIAL_CORE_CONSOLE is not
selected, so uart_console_write is not defined, then we get the error.
Fix this by selecting SERIAL_CORE_CONSOLE.
Fixes: d1a1af2cdf ("hvc: dcc: Add earlycon support")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Link: https://lore.kernel.org/r/20200919063535.2809707-1-yangyingliang@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
sg_init_table zeroes its first argument, so the allocation of that argument
doesn't have to.
the semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression x,n,flags;
@@
x =
- kcalloc
+ kmalloc_array
(n,sizeof(struct scatterlist),flags)
...
sg_init_table(x,n)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@inria.fr>
Link: https://lore.kernel.org/r/1600601186-7420-2-git-send-email-Julia.Lawall@inria.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We need the tty/serial fixes in here and this resolves a merge issue in
the 8250 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As a part of system suspend uart_port_suspend is called from the
Serial driver, which calls set_mctrl passing mctrl as 0. This
makes RFR high(NOT_READY) during suspend.
Due to this BT SoC is not able to send wakeup bytes to UART during
suspend. Include if check for non-suspend case to keep RFR low
during suspend.
Signed-off-by: satya priya <skakit@codeaurora.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/1599742438-16811-5-git-send-email-skakit@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the port-lock initialisation regression introduced by commit
a3cb39d258 ("serial: core: Allow detach and attach serial device for
console") by making sure that the lock is again initialised during
console setup.
The console may be registered before the serial controller has been
probed in which case the port lock needs to be initialised during
console setup by a call to uart_set_options(). The console-detach
changes introduced a regression in several drivers by effectively
removing that initialisation by not initialising the lock when the port
is used as a console (which is always the case during console setup).
Add back the early lock initialisation and instead use a new
console-reinit flag to handle the case where a console is being
re-attached through sysfs.
The question whether the console-detach interface should have been added
in the first place is left for another discussion.
Note that the console-enabled check in uart_set_options() is not
redundant because of kgdboc, which can end up reinitialising an already
enabled console (see commit 42b6a1baa3 ("serial_core: Don't
re-initialize a previously initialized spinlock.")).
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-3-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit f743061a85 ("serial: core: Initialise spin lock before use in
uart_configure_port()") tried to work around a breakage introduced by
commit a3cb39d258 ("serial: core: Allow detach and attach serial
device for console") by adding a second initialisation of the port lock
when registering the port.
As reported by the build robots [1], this doesn't really solve the
regression introduced by the console-detach changes and also adds a
second redundant initialisation of the lock for normal ports.
Start cleaning up this mess by removing the redundant initialisation and
making sure that the port lock is again initialised once-only for ports
that aren't already in use as a console.
[1] https://lore.kernel.org/r/20200802054852.GR23458@shao2-debian
Fixes: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Fixes: a3cb39d258 ("serial: core: Allow detach and attach serial device for console")
Cc: stable <stable@vger.kernel.org> # 5.7
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200909143101.15389-2-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit c5cbc78acf ("tty: serial: qcom_geni_serial: Initialize baud
in qcom_geni_console_setup") fixed a bug by initting a variable that
was used in some cases without initialization. However, the "default"
baud rate picked by that CL was probably not the best choice. The
chances that anyone out there is trying to run a system with kernel
messages piped out over a 9600 baud serial port is just about nil.
Console messages are printed in a blocking manner. At 9600 baud we
print about 1 character per millisecond which means that printing a
40-byte message to the console will take ~40 ms. While it would
probably work, it's going to make boot _very_ slow and probably cause
the occasional timeout here and there in drivers (heck, even at 115200
console delays can wreck havoc).
This has already bit at least two people that I'm aware of that tried
to enable serial console by just adding "console=ttyMSM0" (instead of
"console=ttyMSM0,115200n8") to the command line, so it seems like it'd
be nice to fix.
Let's switch the default to 115200.
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20200911080054.1.I4c00b921c2f17b6988688046fa7be0f729f8d591@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To use mmio32, we also need to set regshift.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Eddie Huang <eddie.huang@mediatek.com>
Link: https://lore.kernel.org/r/20200915054825.3289105-2-hsinyi@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
8250 devices may modify iotype in their own earlycon setup. For example:
8250_mtk and 8250_uniphier force iotype to be MMIO32. Print earlycon info
after match->setup to reflect actual earlycon info.
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Link: https://lore.kernel.org/r/20200915054825.3289105-1-hsinyi@chromium.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This eliminates the following sparse warning:
drivers/tty/serial/ucc_uart.c:286:6: warning: symbol 'qe_uart_set_mctrl'
was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Jason Yan <yanaijie@huawei.com>
Link: https://lore.kernel.org/r/20200912033834.143166-1-yanaijie@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
-----BEGIN PGP SIGNATURE-----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=bjMI
-----END PGP SIGNATURE-----
Merge tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into arm/soc
Samsung S3C24xx and S3C64xx machine code cleanup for v5.10
Big cleanup for the Samsung S3C24xx and S3C64xx platforms, although it
also touches files shared with S5Pv210 and Exynos. This is mostly Arnd
Bergmann work which Krzysztof Kozlowski took over, rebased and polished.
The goal is to cleanup, merge and finally make the Samsung S3C24xx and
S3C64xx architectures multiplatform. The multiplatform did not happen
yet here - just cleaning up and merging into one arch/arm/mach-s3c
directory. However this is step forward for multiplatform or at least
to keep this code still maintainable.
This pulls also branch with changes for Samsung SoC sound drivers from
broonie/sound because the cleanups there were part of this series and
all further patches depend on them.
* tag 'samsung-soc-s3c-5.10' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux: (62 commits)
ARM: s3c: Avoid naming clash of S3C24xx and S3C64xx timer setup
ARM: s3c: Cleanup from old plat-samsung include
ARM: s3c: make headers local if possible
ARM: s3c: move into a common directory
ARM: s3c24xx: stop including mach/hardware.h from mach/io.h
cpufreq: s3c24xx: move low-level clk reg access into platform code
cpufreq: s3c2412: use global s3c2412_cpufreq_setrefresh
ARM: s3c: remove cpufreq header dependencies
cpufreq: s3c24xx: split out registers
fbdev: s3c2410fb: remove mach header dependency
ARM: s3c24xx: bast: avoid irq_desc array usage
ARM: s3c24xx: spi: avoid hardcoding fiq number in driver
ARM: s3c24xx: include mach/irqs.h where needed
ARM: s3c24xx: move s3cmci pinctrl handling into board files
ARM: s3c24xx: move iis pinctrl config into boards
ARM: s3c24xx: move spi fiq handler into platform
ARM: s3c: adc: move header to linux/soc/samsung
ARM: s3c24xx: move irqchip driver back into platform
ARM: s3c24xx: move regs-spi.h into spi driver
ARM: s3c64xx: remove mach/hardware.h
...
Link: https://lore.kernel.org/r/20200831154751.7551-1-krzk@kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
SB1250 uart bug is related to PASS 2 workarounds. Use config
CONFIG_SB1_PASS_2_WORKAROUNDS directly and get rid of SIBYTE_1956_WAR.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
The code currently NULLs tty->driver_data in hvcs_close() with the
intent of informing the next call to hvcs_open() that device needs to be
reconfigured. However, when hvcs_cleanup() is called we copy hvcsd from
tty->driver_data which was previoulsy NULLed by hvcs_close() and our
call to tty_port_put(&hvcsd->port) doesn't actually do anything since
&hvcsd->port ends up translating to NULL by chance. This has the side
effect that when hvcs_remove() is called we have one too many port
references preventing hvcs_destuct_port() from ever being called. This
also prevents us from reusing the /dev/hvcsX node in a future
hvcs_probe() and we can eventually run out of /dev/hvcsX devices.
Fix this by waiting to NULL tty->driver_data in hvcs_cleanup().
Fixes: 27bf7c43a1 ("TTY: hvcs, add tty install")
Signed-off-by: Tyrel Datwyler <tyreld@linux.ibm.com>
Link: https://lore.kernel.org/r/20200820234643.70412-1-tyreld@linux.ibm.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ipwireless_send_packet() can only return 0 on success and -ENOMEM on
error, the caller should check non zero for error condition
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Acked-by: David Sterba <dsterba@suse.com>
Link: https://lore.kernel.org/r/20200821161942.36589-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds support for ACPI enumerated FSL 16550 UARTs.
For supporting ACPI, I added a wrapper so that this driver
can be used if firmware has exposed the HID "NXP0018" in
DSDT table.
This will be built as object file if config "SERIAL_8250_FSL"
is enabled which depends on config "SERIAL_8250_CONSOLE".
Signed-off-by: kuldip dwivedi <kuldip.dwivedi@puresoftware.com>
Link: https://lore.kernel.org/r/20200903113402.12371-1-kuldip.dwivedi@puresoftware.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
While the STM32 does support RS485 drive-enable control within the
UART IP itself, some systems have the drive-enable line connected
to a pin which cannot be pinmuxed as RTS. Add support for toggling
the RTS GPIO line using the modem control GPIOs to provide at least
some sort of emulation.
Fixes: 7df5081cbf ("serial: stm32: Add RS485 RTS GPIO control")
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: linux-stm32@st-md-mailman.stormreply.com
Link: https://lore.kernel.org/r/20200831171045.205691-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
parse_options() in drivers/tty/serial/earlycon.c calls uart_parse_earlycon
in drivers/tty/serial/serial_core.c therefore selecting SERIAL_EARLYCON
should automatically select SERIAL_CORE, otherwise will result in symbol
not found error during linking if SERIAL_CORE is not configured as builtin
Fixes: 9aac588759 ("tty/serial: add generic serial earlycon")
Signed-off-by: Tong Zhang <ztong0001@gmail.com>
Link: https://lore.kernel.org/r/20200828123949.2642-1-ztong0001@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some derivates of sc16is7xx devices expose more than one tty device to
userspace. If multiple such devices exist in a system, userspace
currently has no clean way to infer which tty maps to which physical
line.
Set the .iobase value to the relative index within the device to allow
infering the order through sysfs.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20200901120329.4176302-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20200901153100.18827-2-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Common pattern of handling deferred probe can be simplified with
dev_err_probe(). Less code and the error value gets printed.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/20200901153100.18827-1-krzk@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When calculate "ucr1" UCR1_TRDYEN is duplicate.
Signed-off-by: Ye Bin <yebin10@huawei.com>
Reviewed-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20200903062401.692442-1-yebin10@huawei.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iQFSBAABCAA8FiEEq68RxlopcLEwq+PEeb4+QwBBGIYFAl9ML+IeHHRvcnZhbGRz
QGxpbnV4LWZvdW5kYXRpb24ub3JnAAoJEHm+PkMAQRiGA8EIAIy/kTbFS0yrE9yV
hb98oX0z9+EU9YQg9vhaRWwPd+rJF/JMQZLqYcwbhjG9abaUL3T3fEcSAefMHw8E
LAt+hYzA38dHt7tqhsFQX3vV1VorvDVICBVN0yRPRWKKikq4OPIHzaAR9tleGAF5
8btQisl1PjN+obwYmLuNb6aX16OCwAF+uXOwehcoJs9dvMNhwtXRzfOflWzOvOo6
tE0bHErlylLDfLv4ZzEfczTdks4QJZ7C0xLSf3oN9AAynW42Xnhct4hi8qZY/hCf
CMaqeN4hdpub6TvQIqBdDqMMjEXGFgeNSnAEBQY9VpvUqz8NTu6sQxwgJEKDF5tg
d81lv2c=
=uW/F
-----END PGP SIGNATURE-----
Merge 5.9-rc3 into tty-next
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add PCI id for WCH384_8S 8 port PCI-E serial card.
because this card has so many ports, you may have
to check these two options before use it:
CONFIG_SERIAL_8250_RUNTIME_UARTS
CONFIG_SERIAL_8250_NR_UARTS
Signed-off-by: Du Huanpeng <u74147@gmail.com>
Link: https://lore.kernel.org/r/1598060848-27807-1-git-send-email-u74147@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_pm_opp_of_remove_table() doesn't report any errors when it fails to
find the OPP table with error -ENODEV (i.e. OPP table not present for
the device). And we can call dev_pm_opp_of_remove_table()
unconditionally here.
While at it, create a new label to put clkname on errors.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Link: https://lore.kernel.org/r/583003f385a103b4c089ce8144a215c58cfb117a.1598594714.git.viresh.kumar@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As per the documentation (Documentation/filesystems/sysfs.rst),
snprintf() should not be used for formatting values returned by sysfs.
For all of the instances in serial_core.c, we know that the string will
be <PAGE_SIZE in length, so just use sprintf().
Issue identified by Coccinelle.
Signed-off-by: Alex Dewar <alex.dewar90@gmail.com>
Link: https://lore.kernel.org/r/20200824223932.27709-1-alex.dewar90@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here are a few small TTY/Serial/vt fixes for 5.9-rc3
Included in here are:
- qcom serial fixes
- vt ioctl and core bugfixes
- pl011 serial driver fixes
- 8250 serial driver fixes
- other misc serial driver fixes
and for good measure:
- fbcon fix for syzbot found problem.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX0Zl1w8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykh0wCgicGyVAq3OUH9iTlgYqdkFHL1FWoAnAtP/jot
dB0yRgk2r+RvDL9Odb2u
=x5GL
-----END PGP SIGNATURE-----
Merge tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial fixes from Greg KH:
"Here are a few small TTY/Serial/vt fixes for 5.9-rc3
Included in here are:
- qcom serial fixes
- vt ioctl and core bugfixes
- pl011 serial driver fixes
- 8250 serial driver fixes
- other misc serial driver fixes
and for good measure:
- fbcon fix for syzbot found problem.
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.9-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
tty: serial: imx: add dependence and build for earlycon
serial: samsung: Removes the IRQ not found warning
serial: 8250: change lock order in serial8250_do_startup()
serial: stm32: avoid kernel warning on absence of optional IRQ
serial: pl011: Fix oops on -EPROBE_DEFER
serial: pl011: Don't leak amba_ports entry on driver register error
serial: 8250_exar: Fix number of ports for Commtech PCIe cards
tty: serial: qcom_geni_serial: Drop __init from qcom_geni_console_setup
serial: qcom_geni_serial: Fix recent kdb hang
vt_ioctl: change VT_RESIZEX ioctl to check for error return from vc_resize()
fbcon: prevent user font height or width change from causing potential out-of-bounds access
vt: defer kfree() of vc_screenbuf in vc_do_resize()
This reverts commit b1c32fcfad, because
Syzkaller reports a use-after-free, a write in vcs_read:
BUG: KASAN: use-after-free in vcs_read_buf drivers/tty/vt/vc_screen.c:357 [inline]
BUG: KASAN: use-after-free in vcs_read+0xaa7/0xb40 drivers/tty/vt/vc_screen.c:449
Write of size 2 at addr ffff8880a8014000 by task syz-executor.5/16936
CPU: 1 PID: 16936 Comm: syz-executor.5 Not tainted 5.9.0-rc1-next-20200820-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
...
kasan_report.cold+0x1f/0x37 mm/kasan/report.c:530
vcs_read_buf drivers/tty/vt/vc_screen.c:357 [inline]
vcs_read+0xaa7/0xb40 drivers/tty/vt/vc_screen.c:449
There are two issues with the patch:
1) vcs_read rounds the 'count' *up* to an even number. So if we read odd
bytes from the header (3 bytes in the reproducer), the second byte of
a (2-byte/ushort) write to temporary con_buf won't fit. It is because
with the patch applied, we only subtract the real number read (3 bytes)
and not the whole header (4 bytes).
2) in this scenario, we perform unaligned accesses now: there are
2-byte/ushort writes to odd addresses. Due to the same reason as
above.
Revert this for now, re-think and retry later.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: syzbot+ad1f53726c3bd11180cb@syzkaller.appspotmail.com
Fixes: b1c32fcfad ("vc_screen: extract vcs_read_buf_header")
Cc: akpm@linux-foundation.org
Cc: nico@fluxnic.net
Link: https://lore.kernel.org/r/20200824095425.4376-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The plat-samsung directory and mach-s5pv210 can be build
completely independently, so split the two Kconfig symbols
CONFIG_PLAT_SAMSUNG and CONFIG_ARCH_S5PV210.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Mark Brown <broonie@kernel.org>
Link: https://lore.kernel.org/r/20200806182059.2431-18-krzk@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Use platform_get_resource() to fetch the memory resource
instead of open-coded variant.
While here, fail the probe if no resource found or no port is added.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200804134807.11589-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In few older Samsung SoCs like s3c2410, s3c2412
and s3c2440, UART IP is having 2 interrupt lines.
However, in other SoCs like s3c6400, s5pv210,
exynos5433, and exynos4210 UART is having only 1
interrupt line. Due to this, "platform_get_irq(platdev, 1)"
call in the driver gives the following false-positive error:
"IRQ index 1 not found" on newer SoC's.
This patch adds the condition to check for Tx interrupt
only for the those SoC's which have 2 interrupt lines.
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Tamseel Shams <m.shams@samsung.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200810030021.45348-1-m.shams@samsung.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
As in the previous patches, fix kernel-doc in synclink drivers. This is
done separately from others, as kernel-doc comments were heavily broken
in these drivers. Convert them to proper ones.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085655.12071-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With W=1, the kernel-doc checker complains quite a lot in the tty layer.
Over the time, many documented parameters were renamed, removed or
switched from tty to tty_port and similar. Some were mistyped in the doc
too.
So fix all these in the tty core. (But do not add the missing ones which
the checker complains about too. Not now.) The rest in the tty layer
will follow in the next patches.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085655.12071-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm->output and ->error are set only to gsmld_output and gsm_error,
respectively. Call these functions directly and remove error and output
function pointers from struct gsm_mux completely.
Note: we need a forward declaration of gsmld_output now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085655.12071-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Do not undefine random words. I guess this was here as there were macros
with such generic names somewhere. I very doubt they still exist. So
drop these.
And remove a spare blank line.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-16-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The attribute header handling is terrible in vcs_read_buf. Separate it
to a new function and simply do memmove (of up to 4 bytes) to the start
of the con_buf -- if user seeked.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-15-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
And finally, move the attributes buffer handling to a separate function.
Leaving vcs_read quite compact.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-14-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The same as making write more readable, extract unicode handling from
vcs_read. The other two cases (w/ and w/o attributes) will follow.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-12-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Both tmp_count computations and the single use can be eliminated using
min(). Do so.
Side note: we need HEADER_SIZE to be unsigned for min() not to complain.
Fix that too as all its other uses do not mind.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-11-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* pos is derived from the passed ppos, so make it long enough, i.e.
loff_t
* attr and uni_mode are booleans, so...
* size is limited by vcs_size() which returns an int
* read, p, orig_count and this_round are always ">= 0" and "< size",
so uint is enough
* row, col, and max_col are derived from vc->vc_cols (uint) and p, so
make them uint too
* tmp_count is derived from this_round, so make it an uint too.
* use u16 * for org (instead of unsigned short *). No need to initialize
org too.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-10-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Introduce a new inline function called vc_compile_le16 and do the shifts
and ORs there. Depending on LE x BE.
I tried cpu_to_le16, but it ends up with worse assembly on BE for
whatever reason -- the compiler seems to be unable to optimize the swap.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-9-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is the counterpart of the previous patch: here, we extract buffer
writing with attributes from vcs_write.
Now, there is no need for org to be initialized to NULL. The org0
check before update_region() confuses compilers, so check org instead.
It provides the same semantics. And it also eliminates the need for
initialization of org0.
We switch the branches of the attr 'if' too, as the inversion brings only
confusion now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-8-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
vcs_write is too long to be readable. Extract buffer handling w/o
attributes from there to a separate function.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-7-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* ret can carry error codes, so make it signed, i.e. ssize_t
* pos is derived from the passed ppos, so make it long enough, i.e.
loff_t
* attr is a boolean, so...
* size is limited by vcs_size() which returns an int
* written, p, orig_count and this_round are always ">= 0" and "< size",
so uint is enough
* col and max_col are derived from vc->vc_cols (uint) and p, so make
them uint too
* place con_buf0 and con_buf declaration to a single line
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-6-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is weird to fetch the information from the inode over and over. Read
and write already have the needed information, so rewrite vcs_size to
accept a vc, attr and unicode and adapt vcs_lseek to that.
Also make sure all sites check the return value of vcs_size for errors.
And document it using kernel-doc.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-5-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
viewed is used as a flag, i.e. bool. So treat is as such in most of the
places. vcs_vc is handled in the next patch.
Note: the last parameter of invert_screen was misnamed in the
declaration since 1.1.92.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-3-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
That is:
1) call the parameter 'xy' to denote what it really is, not generic 'p'
2) tell the compiler and users that we expect an array:
* with at least 2 chars (static 2)
* which we don't modify in putconsxy (const)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There are many functions declared in selection.h which only read from
struct vc_data passed as a parameter. Make all those uses const to hint
the compiler a bit.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20200818085706.12163-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817085921.26033-5-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817085921.26033-4-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817085921.26033-3-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In preparation for unconditionally passing the
struct tasklet_struct pointer to all tasklet
callbacks, switch to using the new tasklet_setup()
and from_tasklet() to pass the tasklet pointer explicitly.
Signed-off-by: Romain Perier <romain.perier@gmail.com>
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Link: https://lore.kernel.org/r/20200817085921.26033-2-allen.cryptic@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
stm32_init_port() of the stm32-usart may trigger a warning in
platform_get_irq() when the device tree specifies no wakeup interrupt.
The wakeup interrupt is usually a board-specific GPIO and the driver
functions correctly in its absence. The mainline stm32mp151.dtsi does
not specify it, so all mainline device trees trigger an unnecessary
kernel warning. Use of platform_get_irq_optional() avoids this.
Fixes: 2c58e56096 ("serial: stm32: fix the get_irq error case")
Signed-off-by: Holger Assmann <h.assmann@pengutronix.de>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813152757.32751-1-h.assmann@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If probing of a pl011 gets deferred until after free_initmem(), an oops
ensues because pl011_console_match() is called which has been freed.
Fix by removing the __init attribute from the function and those it
calls.
Commit 10879ae5f1 ("serial: pl011: add console matching function")
introduced pl011_console_match() not just for early consoles but
regular preferred consoles, such as those added by acpi_parse_spcr().
Regular consoles may be registered after free_initmem() for various
reasons, one being deferred probing, another being dynamic enablement
of serial ports using a DeviceTree overlay.
Thus, pl011_console_match() must not be declared __init and the
functions it calls mustn't either.
Stack trace for posterity:
Unable to handle kernel paging request at virtual address 80c38b58
Internal error: Oops: 8000000d [#1] PREEMPT SMP ARM
PC is at pl011_console_match+0x0/0xfc
LR is at register_console+0x150/0x468
[<80187004>] (register_console)
[<805a8184>] (uart_add_one_port)
[<805b2b68>] (pl011_register_port)
[<805b3ce4>] (pl011_probe)
[<80569214>] (amba_probe)
[<805ca088>] (really_probe)
[<805ca2ec>] (driver_probe_device)
[<805ca5b0>] (__device_attach_driver)
[<805c8060>] (bus_for_each_drv)
[<805c9dfc>] (__device_attach)
[<805ca630>] (device_initial_probe)
[<805c90a8>] (bus_probe_device)
[<805c95a8>] (deferred_probe_work_func)
Fixes: 10879ae5f1 ("serial: pl011: add console matching function")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.10+
Cc: Aleksey Makarov <amakarov@marvell.com>
Cc: Peter Hurley <peter@hurleysoftware.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Christopher Covington <cov@codeaurora.org>
Link: https://lore.kernel.org/r/f827ff09da55b8c57d316a1b008a137677b58921.1597315557.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
pl011_probe() calls pl011_setup_port() to reserve an amba_ports[] entry,
then calls pl011_register_port() to register the uart driver with the
tty layer.
If registration of the uart driver fails, the amba_ports[] entry is not
released. If this happens 14 times (value of UART_NR macro), then all
amba_ports[] entries will have been leaked and driver probing is no
longer possible. (To be fair, that can only happen if the DeviceTree
doesn't contain alias IDs since they cause the same entry to be used for
a given port.) Fix it.
Fixes: ef2889f7ff ("serial: pl011: Move uart_register_driver call to device")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v3.15+
Cc: Tushar Behera <tushar.behera@linaro.org>
Link: https://lore.kernel.org/r/138f8c15afb2f184d8102583f8301575566064a6.1597316167.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The following in 8250_exar.c line 589 is used to determine the number
of ports for each Exar board:
nr_ports = board->num_ports ? board->num_ports : pcidev->device & 0x0f;
If the number of ports a card has is not explicitly specified, it defaults
to the rightmost 4 bits of the PCI device ID. This is prone to error since
not all PCI device IDs contain a number which corresponds to the number of
ports that card provides.
This particular case involves COMMTECH_4222PCIE, COMMTECH_4224PCIE and
COMMTECH_4228PCIE cards with device IDs 0x0022, 0x0020 and 0x0021.
Currently the multiport cards receive 2, 0 and 1 port instead of 2, 4 and
8 ports respectively.
To fix this, each Commtech Fastcom PCIe card is given a struct where the
number of ports is explicitly specified. This ensures 'board->num_ports'
is used instead of the default 'pcidev->device & 0x0f'.
Fixes: d0aeaa83f0 ("serial: exar: split out the exar code from 8250_pci")
Signed-off-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Tested-by: Valmer Huhn <valmer.huhn@concurrent-rt.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200813165255.GC345440@icarus.concurrent-rt.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The commit e42d6c3ec0 ("serial: qcom_geni_serial: Make kgdb work
even if UART isn't console") worked pretty well and I've been doing a
lot of debugging with it. However, recently I typed "dmesg" in kdb
and then held the space key down to scroll through the pagination. My
device hung. This was repeatable and I found that it was introduced
with the aforementioned commit.
It turns out that there are some strange boundary cases in geni where
in some weird situations it will signal RX_LAST but then will put 0 in
RX_LAST_BYTE. This means that the entire last FIFO entry is valid.
This weird corner case is handled in qcom_geni_serial_handle_rx()
where you can see that we only honor RX_LAST_BYTE if RX_LAST is set
_and_ RX_LAST_BYTE is non-zero. If either of these is not true we use
BYTES_PER_FIFO_WORD (4) for the size of the last FIFO word.
Let's fix kgdb. While at it, also use the proper #define for 4.
Fixes: e42d6c3ec0 ("serial: qcom_geni_serial: Make kgdb work even if UART isn't console")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Akash Asthana <akashast@codeaurora.org>
Link: https://lore.kernel.org/r/20200806221904.1.I4455ff86f0ef5281c2a0cd0a4712db614548a5ca@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
syzbot is reporting UAF bug in set_origin() from vc_do_resize() [1], for
vc_do_resize() calls kfree(vc->vc_screenbuf) before calling set_origin().
Unfortunately, in set_origin(), vc->vc_sw->con_set_origin() might access
vc->vc_pos when scroll is involved in order to manipulate cursor, but
vc->vc_pos refers already released vc->vc_screenbuf until vc->vc_pos gets
updated based on the result of vc->vc_sw->con_set_origin().
Preserving old buffer and tolerating outdated vc members until set_origin()
completes would be easier than preventing vc->vc_sw->con_set_origin() from
accessing outdated vc members.
[1] https://syzkaller.appspot.com/bug?id=6649da2081e2ebdc65c0642c214b27fe91099db3
Reported-by: syzbot <syzbot+9116ecc1978ca3a12f43@syzkaller.appspotmail.com>
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1596034621-4714-1-git-send-email-penguin-kernel@I-love.SAKURA.ne.jp
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Here is the large set of TTY and Serial driver patches for 5.9-rc1.
Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt and
console code.
Other highlights include:
- much needed vt/vc code cleanup from Jiri Slaby
- 8250 driver fixes and additions
- various serial driver updates and feature enhancements
- locking cleanup for serial/console initializations
- other minor cleanups
All of these have been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXyv30A8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynW+gCgv+OqxT0jeNRAMSQcpMvP3wTBMKIAn1StfjJ4
y8uwZuQQimD49uj8XtDq
=bKSv
-----END PGP SIGNATURE-----
Merge tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial updates from Greg KH:
"Here is the large set of TTY and Serial driver patches for 5.9-rc1.
Lots of bugfixes in here, thanks to syzbot fuzzing for serial and vt
and console code.
Other highlights include:
- much needed vt/vc code cleanup from Jiri Slaby
- 8250 driver fixes and additions
- various serial driver updates and feature enhancements
- locking cleanup for serial/console initializations
- other minor cleanups
All of these have been in linux-next with no reported issues"
* tag 'tty-5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (90 commits)
MAINTAINERS: enlist Greg formally for console stuff
vgacon: Fix for missing check in scrollback handling
Revert "serial: 8250: Let serial core initialise spin lock"
serial: 8250: Let serial core initialise spin lock
tty: keyboard, do not speculate on func_table index
serial: stm32: Add RS485 RTS GPIO control
serial: 8250_dw: Fix common clocks usage race condition
serial: 8250_dw: Pass the same rate to the clk round and set rate methods
serial: 8250_dw: Simplify the ref clock rate setting procedure
serial: 8250: Add 8250 port clock update method
tty: serial: imx: add imx earlycon driver
tty: serial: imx: enable imx serial console port as module
tty/synclink: remove leftover bits of non-PCI card support
tty: Use the preferred form for passing the size of a structure type
tty: Fix identation issues in struct serial_struct32
tty: Avoid the use of one-element arrays
serial: msm_serial: add sparse context annotation
serial: pmac_zilog: add sparse context annotation
newport_con: vc_color is now in state
serial: imx: use hrtimers for rs485 delays
...
static priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low' priority level,
plus sched_set_normal() to set the policy back to non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in a separate
tree.
When merging to the latest upstream tree there's a conflict in drivers/spi/spi.c,
which can be resolved via:
sched_set_fifo(ctlr->kworker_task);
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----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=/7JH
-----END PGP SIGNATURE-----
Merge tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull sched/fifo updates from Ingo Molnar:
"This adds the sched_set_fifo*() encapsulation APIs to remove static
priority level knowledge from non-scheduler code.
The three APIs for non-scheduler code to set SCHED_FIFO are:
- sched_set_fifo()
- sched_set_fifo_low()
- sched_set_normal()
These are two FIFO priority levels: default (high), and a 'low'
priority level, plus sched_set_normal() to set the policy back to
non-SCHED_FIFO.
Since the changes affect a lot of non-scheduler code, we kept this in
a separate tree"
* tag 'sched-fifo-2020-08-04' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (24 commits)
sched,tracing: Convert to sched_set_fifo()
sched: Remove sched_set_*() return value
sched: Remove sched_setscheduler*() EXPORTs
sched,psi: Convert to sched_set_fifo_low()
sched,rcutorture: Convert to sched_set_fifo_low()
sched,rcuperf: Convert to sched_set_fifo_low()
sched,locktorture: Convert to sched_set_fifo()
sched,irq: Convert to sched_set_fifo()
sched,watchdog: Convert to sched_set_fifo()
sched,serial: Convert to sched_set_fifo()
sched,powerclamp: Convert to sched_set_fifo()
sched,ion: Convert to sched_set_normal()
sched,powercap: Convert to sched_set_fifo*()
sched,spi: Convert to sched_set_fifo*()
sched,mmc: Convert to sched_set_fifo*()
sched,ivtv: Convert to sched_set_fifo*()
sched,drm/scheduler: Convert to sched_set_fifo*()
sched,msm: Convert to sched_set_fifo*()
sched,psci: Convert to sched_set_fifo*()
sched,drbd: Convert to sched_set_fifo*()
...
-----BEGIN PGP SIGNATURE-----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=ZcMq
-----END PGP SIGNATURE-----
Merge tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux
Pull printk updates from Petr Mladek:
- Herbert Xu made printk header file self-contained.
- Andy Shevchenko and Sergey Senozhatsky cleaned up console->setup()
error handling.
- Andy Shevchenko did some cleanups (e.g. sparse warning) in vsprintf
code.
- Minor documentation updates.
* tag 'printk-for-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/printk/linux:
lib/vsprintf: Force type of flags value for gfp_t
lib/vsprintf: Replace custom spec to print decimals with generic one
lib/vsprintf: Replace hidden BUILD_BUG_ON() with static_assert()
printk: Make linux/printk.h self-contained
doc:kmsg: explicitly state the return value in case of SEEK_CUR
Replace HTTP links with HTTPS ones: vsprintf
hvc: unify console setup naming
console: Fix trivia typo 'change' -> 'chance'
console: Propagate error code from console ->setup()
tty: hvc: Return proper error code from console ->setup() hook
serial: sunzilog: Return proper error code from console ->setup() hook
serial: sunsab: Return proper error code from console ->setup() hook
mips: Return proper error code from console ->setup() hook
- Prepare for tasklet API modernization (Romain Perier, Allen Pais, Kees Cook)
-----BEGIN PGP SIGNATURE-----
iQJKBAABCgA0FiEEpcP2jyKd1g9yPm4TiXL039xtwCYFAl8oXpMWHGtlZXNjb29r
QGNocm9taXVtLm9yZwAKCRCJcvTf3G3AJtJgEACVb88nzYwu5mC5ZcfvwSyXeQsR
eDpCkX5HT6CsxlOn0/YJvxUtkkerQftbRuAXrzoUpQkpyBh82PviVZFKDS7NE9Lc
6xPqloi2gbZ8EfgMraVynL+9lpLh0+qNCM7LPg4xT+JxMDLut/nWRdrp8d7uBYfQ
AXV6CV4Tc4ijOMROV6AEVVdSTzkRCbiqUnRDBLETBfiJOdDn5MgJgxicWvN5FTpu
PiUVF3CtWaKCRfQO/GEAXTG65hOtmql5IbX9n7uooNu/wCCnEFfVUus1uTcsrqxN
ByrZ56NVPoO7z2jYLt8Lft3myo2e/mn88PKqrzS2p9GPn0VBv7rcO3ePmbbHL/RA
mp+pg8wdpmKrHv4YGfsF+obT1v8f6VJoTLUt5S/WqZAzl1sVJgEJdAkjmDKythGG
yYKKCemMceMMzLXxnFAYMzdXzdXZ3YEpiW4UkBb77EhUisDrLxCHSL5t4UzyWnuO
Gtzw7N69iHPHLsxAk1hESAD8sdlk2EdN6vzJVelOsiW955x1hpR+msvNpwZwBqdq
A2h8VnnrxLK2APl93T5VW9T6kvhzaTwLhoCH+oKklE+U0XJTAYZ4D/AcRVghBvMg
bC1+1vDx+t/S+8P308evPQnEygLtL2I+zpPnBA1DZzHRAoY8inCLc5HQOfr6pi/f
koNTtKkmSSKaFSYITw==
=hb+e
-----END PGP SIGNATURE-----
Merge tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull tasklets API update from Kees Cook:
"These are the infrastructure updates needed to support converting the
tasklet API to something more modern (and hopefully for removal
further down the road).
There is a 300-patch series waiting in the wings to get set out to
subsystem maintainers, but these changes need to be present in the
kernel first. Since this has some treewide changes, I carried this
series for -next instead of paining Thomas with it in -tip, but it's
got his Ack.
This is similar to the timer_struct modernization from a while back,
but not nearly as messy (I hope). :)
- Prepare for tasklet API modernization (Romain Perier, Allen Pais,
Kees Cook)"
* tag 'tasklets-v5.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux:
tasklet: Introduce new initialization API
treewide: Replace DECLARE_TASKLET() with DECLARE_TASKLET_OLD()
usb: gadget: udc: Avoid tasklet passing a global
A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory
subsystem and its drivers, starting out with a set of cleanup
patches.
A larger driver for the Tegra memory controller that was accidentally
missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware blobs
The tegra firmware driver gets extended to export some debug information
Various updates to i.MX firmware drivers, mostly cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space.
A new firmware based trusted platform module (fTPM) driver is added
based on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for identifying
a machine through the SMCCC ARCH_SOC_ID firmware interface rather than
by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device code.
There are also a number of updates to SoC specific drivers,
the main ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver
-----BEGIN PGP SIGNATURE-----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=nezz
-----END PGP SIGNATURE-----
Merge tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A couple of subsystems have their own subsystem maintainers but choose
to have the code merged through the soc tree as upstream, as the code
tends to be used across multiple SoCs or has SoC specific drivers
itself:
- memory controllers:
Krzysztof Kozlowski takes ownership of the drivers/memory subsystem
and its drivers, starting out with a set of cleanup patches.
A larger driver for the Tegra memory controller that was
accidentally missed for v5.8 is now added.
- reset controllers:
Only minor updates to drivers/reset this time
- firmware:
The "turris mox" firmware driver gains support for signed firmware
blobs The tegra firmware driver gets extended to export some debug
information Various updates to i.MX firmware drivers, mostly
cosmetic
- ARM SCMI/SCPI:
A new mechanism for platform notifications is added, among a number
of minor changes.
- optee:
Probing of the TEE bus is rewritten to better support detection of
devices that depend on the tee-supplicant user space. A new
firmware based trusted platform module (fTPM) driver is added based
on OP-TEE
- SoC attributes:
A new driver is added to provide a generic soc_device for
identifying a machine through the SMCCC ARCH_SOC_ID firmware
interface rather than by probing SoC family specific registers.
The series also contains some cleanups to the common soc_device
code.
There are also a number of updates to SoC specific drivers, the main
ones are:
- Mediatek cmdq driver gains a few in-kernel interfaces
- Minor updates to Qualcomm RPMh, socinfo, rpm drivers, mostly adding
support for additional SoC variants
- The Qualcomm GENI core code gains interconnect path voting and
performance level support, and integrating this into a number of
device drivers.
- A new driver for Samsung Exynos5800 voltage coupler for
- Renesas RZ/G2H (R8A774E1) SoC support gets added to a couple of SoC
specific device drivers
- Updates to the TI K3 Ring Accelerator driver"
* tag 'arm-drivers-5.9' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (164 commits)
soc: qcom: geni: Fix unused label warning
soc: qcom: smd-rpm: Fix kerneldoc
memory: jz4780_nemc: Only request IO memory the driver will use
soc: qcom: pdr: Reorder the PD state indication ack
MAINTAINERS: Add Git repository for memory controller drivers
memory: brcmstb_dpfe: Fix language typo
memory: samsung: exynos5422-dmc: Correct white space issues
memory: samsung: exynos-srom: Correct alignment
memory: pl172: Enclose macro argument usage in parenthesis
memory: of: Correct kerneldoc
memory: omap-gpmc: Fix language typo
memory: omap-gpmc: Correct white space issues
memory: omap-gpmc: Use 'unsigned int' for consistency
memory: omap-gpmc: Enclose macro argument usage in parenthesis
memory: omap-gpmc: Correct kerneldoc
memory: mvebu-devbus: Align with open parenthesis
memory: mvebu-devbus: Add missing braces to all arms of if statement
memory: bt1-l2-ctl: Add blank lines after declarations
soc: TI knav_qmss: make symbol 'knav_acc_range_ops' static
firmware: ti_sci: Replace HTTP links with HTTPS ones
...
-----BEGIN PGP SIGNATURE-----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=abJG
-----END PGP SIGNATURE-----
Merge tag 'for-5.9/block-20200802' of git://git.kernel.dk/linux-block
Pull core block updates from Jens Axboe:
"Good amount of cleanups and tech debt removals in here, and as a
result, the diffstat shows a nice net reduction in code.
- Softirq completion cleanups (Christoph)
- Stop using ->queuedata (Christoph)
- Cleanup bd claiming (Christoph)
- Use check_events, moving away from the legacy media change
(Christoph)
- Use inode i_blkbits consistently (Christoph)
- Remove old unused writeback congestion bits (Christoph)
- Cleanup/unify submission path (Christoph)
- Use bio_uninit consistently, instead of bio_disassociate_blkg
(Christoph)
- sbitmap cleared bits handling (John)
- Request merging blktrace event addition (Jan)
- sysfs add/remove race fixes (Luis)
- blk-mq tag fixes/optimizations (Ming)
- Duplicate words in comments (Randy)
- Flush deferral cleanup (Yufen)
- IO context locking/retry fixes (John)
- struct_size() usage (Gustavo)
- blk-iocost fixes (Chengming)
- blk-cgroup IO stats fixes (Boris)
- Various little fixes"
* tag 'for-5.9/block-20200802' of git://git.kernel.dk/linux-block: (135 commits)
block: blk-timeout: delete duplicated word
block: blk-mq-sched: delete duplicated word
block: blk-mq: delete duplicated word
block: genhd: delete duplicated words
block: elevator: delete duplicated word and fix typos
block: bio: delete duplicated words
block: bfq-iosched: fix duplicated word
iocost_monitor: start from the oldest usage index
iocost: Fix check condition of iocg abs_vdebt
block: Remove callback typedefs for blk_mq_ops
block: Use non _rcu version of list functions for tag_set_list
blk-cgroup: show global disk stats in root cgroup io.stat
blk-cgroup: make iostat functions visible to stat printing
block: improve discard bio alignment in __blkdev_issue_discard()
block: change REQ_OP_ZONE_RESET and REQ_OP_ZONE_RESET_ALL to be odd numbers
block: defer flush request no matter whether we have elevator
block: make blk_timeout_init() static
block: remove retry loop in ioc_release_fn()
block: remove unnecessary ioc nested locking
block: integrate bd_start_claiming into __blkdev_get
...
This reverts commit 679193b7ba.
It appears that in QEmu the lock has been initialised differently
(it wasn't obvious on real hardware during testing). Let's
revert the change until the better approach will be developed.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200802111612.36189-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since the serial core handles spin lock initialisation,
let the driver rely on it.
Depends-on: f743061a85 ("serial: core: Initialise spin lock before use in uart_configure_port()")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200731123733.22754-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is very unlikely for processor to speculate on the func_table index.
The index is uchar and func_table is of size 256. So the compiler would
need to screw up and generate a really bad code.
But to stay on the safe side, forbid speculation on this user passed
index.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Jiri Kosina <jikos@kernel.org>
Link: https://lore.kernel.org/r/20200730105546.24268-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This converts all the existing DECLARE_TASKLET() (and ...DISABLED)
macros with DECLARE_TASKLET_OLD() in preparation for refactoring the
tasklet callback type. All existing DECLARE_TASKLET() users had a "0"
data argument, it has been removed here as well.
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Kees Cook <keescook@chromium.org>
While the STM32 does support RS485 drive-enable control within the
UART IP itself, some systems have the drive-enable line connected
to a pin which cannot be pinmuxed as RTS. Add support for toggling
the RTS GPIO line using the modem control GPIOs to provide at least
some sort of emulation.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Fabrice Gasnier <fabrice.gasnier@st.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-stm32@st-md-mailman.stormreply.com
Link: https://lore.kernel.org/r/20200725144947.537007-1-marex@denx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The race condition may happen if the UART reference clock is shared with
some other device (on Baikal-T1 SoC it's another DW UART port). In this
case if that device changes the clock rate while serial console is using
it the DW 8250 UART port might not only end up with an invalid uartclk
value saved, but may also experience a distorted output data since
baud-clock could have been changed. In order to fix this lets at least
try to adjust the 8250 port setting like UART clock rate in case if the
reference clock rate change is discovered. The driver will call the new
method to update 8250 UART port clock rate settings. It's done by means of
the clock event notifier registered at the port startup and unregistered
in the shutdown callback method.
Note 1. In order to avoid deadlocks we had to execute the UART port update
method in a dedicated deferred work. This is due to (in my opinion
redundant) the clock update implemented in the dw8250_set_termios()
method.
Note 2. Before the ref clock is manually changed by the custom
set_termios() function we swap the port uartclk value with new rate
adjusted to be suitable for the requested baud. It is necessary in
order to effectively disable a functionality of the ref clock events
handler for the current UART port, since uartclk update will be done
a bit further in the generic serial8250_do_set_termios() function.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-5-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Indeed according to the clk API if clk_round_rate() has successfully
accepted a rate, then in order setup the clock with value returned by the
clk_round_rate() the clk_set_rate() method must be called with the
original rate value.
Suggested-by: Russell King <linux@armlinux.org.uk>
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-4-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Really instead of twice checking the clk_round_rate() return value
we could do it once, and if it isn't error the clock rate can be changed.
By doing so we decrease a number of ret-value tests and remove a weird
goto-based construction implemented in the dw8250_set_termios() method.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-3-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Some platforms can be designed in a way so the UART port reference clock
might be asynchronously changed at some point. In Baikal-T1 SoC this may
happen due to the reference clock being shared between two UART ports, on
the Allwinner SoC the reference clock is derived from the CPU clock, so
any CPU frequency change should get to be known/reflected by/in the UART
controller as well. But it's not enough to just update the
uart_port->uartclk field of the corresponding UART port, the 8250
controller reference clock divisor should be altered so to preserve
current baud rate setting. All of these things is done in a coherent
way by calling the serial8250_update_uartclk() method provided in this
patch. Though note that it isn't supposed to be called from within the
UART port callbacks because the locks using to the protect the UART port
data are already taken in there.
Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>
Link: https://lore.kernel.org/r/20200723003357.26897-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Split imx earlycon driver from imx serial driver "imx.c" as
separated driver. imx serial driver can be built as module,
but earlycon driver only support build in.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200724070815.11445-3-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add support for building i.MX serial driver as module.
The changes of the patch:
- imx console driver can be built as module.
- move out earlycon code to separated driver like imx_earlycon.c,
and imx earlycon driver only support build-in.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20200724070815.11445-2-fugang.duan@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 1355cba9c3 ("tty/synclink: remove ISA support"), the
synlink driver only supports PCI card. Remove any leftover dead code
to support other cards.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200727130501.31005-1-hch@lst.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the preferred form for passing the size of a structure type. The
alternative form where the structure type is spelled out hurts
readability and introduces an opportunity for a bug when the object
type is changed but the corresponding object identifier to which the
sizeof operator is applied is not.
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/b04dd8cdd67bd6ffde3fd12940aeef35fdb824a6.1595543280.git.gustavoars@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix the following checkpatch.pl warnings together with all the
identation issues in struct serial_struct32:
ERROR: code indent should use tabs where possible
+ char reserved_char;$
WARNING: please, no spaces at the start of a line
+ char reserved_char;$
ERROR: code indent should use tabs where possible
+ compat_int_t reserved;$
WARNING: please, no spaces at the start of a line
+ compat_int_t reserved;$
Acked-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Link: https://lore.kernel.org/r/77576843397aeab0af8aa0423a9768f3ca8dedfb.1595543280.git.gustavoars@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Corey Minyard