Some SoCs, eg. mt8183, are using a pinconfig operation bias_set_combo.
The fallback path in mtk_pinconf_adv_pull_set() should also try this
operation.
Fixes: cafe19db77 ("pinctrl: mediatek: Backward compatible to previous Mediatek's bias-pull usage")
Signed-off-by: Hsin-Yi Wang <hsinyi@chromium.org>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/20201228090425.2130569-1-hsinyi@chromium.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Clang warns:
drivers/pinctrl/nomadik/pinctrl-nomadik.c:952:8: warning: unused
variable 'wake' [-Wunused-variable]
bool wake;
^
1 warning generated.
There were two wake declarations added to nmk_gpio_dbg_show_one when
converting it to use irq_has_action but only one is used within its
scope. Remove the unused one so there is no more warning.
Fixes: f3925032d7 ("pinctrl: nomadik: Use irq_has_action()")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Tested-by: Andrew Halaney <ajhalaney@gmail.com>
Reviewed-by: Andrew Halaney <ajhalaney@gmail.com>
Reported-by: Hulk Robot <hulkci@huawei.com>
Reported-by: Ye Bin <yebin10@huawei.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Link: https://lore.kernel.org/r/20201229204710.1129033-1-natechancellor@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove all empty lines at the end of functions in pinctrl subsystem,
and make the code neat.
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Zhaoyu Liu <zackaryliu@yeah.net>
Link: https://lore.kernel.org/r/X98NP6NFK1Afzrgd@manjaro
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The SCU offset for signal PWM8 in group PWM8G0 is wrong, fix it from
SCU414 to SCU4B4.
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Fixes: 2eda1cdec4 ("pinctrl: aspeed: Add AST2600 pinmux support")
Reviewed-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20201217024912.3198-1-billy_tsai@aspeedtech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Kernel test robot reported the following warning:
'warning: no previous prototype for 'rt2880_pinmux_init''.
This function is the entry point for the platform driver and
it is private to this driver. Hence declare it 'static' which is
the correct thing to do fixing also this warning.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20201228064727.30098-1-sergio.paracuellos@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some paths in probe function are returning '-EINVAL'
instead of preserve original code from called functions.
Change them to preserve all of them.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201213161721.6514-7-sergio.paracuellos@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When '-ENOMEM' is returned there is not need at all to
add custom error messages. Hence delete it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201213161721.6514-6-sergio.paracuellos@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Memory is being requested to the kernel but there is
a missing check for NULL. Hence, add it.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201213161721.6514-5-sergio.paracuellos@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Double pointer is being used and assigned in a bit dirty way to
assign functions in pinctrl. Instead of doing this just avoid it
and use directly 'p->func' instead.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20201213161721.6514-3-sergio.paracuellos@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Now that JZ4760 support has been fixed, it looks wrong to have
JZ4760_GPIO_* registers being written if the SoC is a JZ4770 or later.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201211232810.261565-2-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- JZ4760 and JZ4760B have a similar register layout as the JZ4740, and
don't use the new register layout, which was introduced with the
JZ4770 SoC and not the JZ4760 or JZ4760B SoCs.
- The JZ4740 code path only expected two function modes to be
configurable for each pin, and wouldn't work with more than two. Fix
it for the JZ4760, which has four configurable function modes.
Fixes: 0257595a5c ("pinctrl: Ingenic: Add pinctrl driver for JZ4760 and JZ4760B.")
Cc: <stable@vger.kernel.org> # 5.3
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20201211232810.261565-1-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
accesses, inefficient and disfunctional code. The goal is to remove the
export of irq_to_desc() to prevent these things from creeping up again.
-----BEGIN PGP SIGNATURE-----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=BXv+
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is the second attempt after the first one failed miserably and
got zapped to unblock the rest of the interrupt related patches.
A treewide cleanup of interrupt descriptor (ab)use with all sorts of
racy accesses, inefficient and disfunctional code. The goal is to
remove the export of irq_to_desc() to prevent these things from
creeping up again"
* tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
genirq: Restrict export of irq_to_desc()
xen/events: Implement irq distribution
xen/events: Reduce irq_info:: Spurious_cnt storage size
xen/events: Only force affinity mask for percpu interrupts
xen/events: Use immediate affinity setting
xen/events: Remove disfunct affinity spreading
xen/events: Remove unused bind_evtchn_to_irq_lateeoi()
net/mlx5: Use effective interrupt affinity
net/mlx5: Replace irq_to_desc() abuse
net/mlx4: Use effective interrupt affinity
net/mlx4: Replace irq_to_desc() abuse
PCI: mobiveil: Use irq_data_get_irq_chip_data()
PCI: xilinx-nwl: Use irq_data_get_irq_chip_data()
NTB/msi: Use irq_has_action()
mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc
pinctrl: nomadik: Use irq_has_action()
drm/i915/pmu: Replace open coded kstat_irqs() copy
drm/i915/lpe_audio: Remove pointless irq_to_desc() usage
s390/irq: Use irq_desc_kstat_cpu() in show_msi_interrupt()
parisc/irq: Use irq_desc_kstat_cpu() in show_interrupts()
...
New drivers:
- New driver for the Microchip Serial GPIO "SGPIO".
- Qualcomm SM8250 LPASS (Low Power Audio Subsystem) GPIO driver.
New subdrivers:
- Intel Lakefield subdriver.
- Intel Elkhart Lake subdriver.
- Intel Alder Lake-S subdriver.
- Qualcomm MSM8953 subdriver.
- Qualcomm SDX55 subdriver.
- Qualcomm SDX55 PMIC subdriver.
- Ocelot Luton SoC subdriver.
- Ocelot Serval SoC subdriver.
Modularization:
- The Meson driver can now be built as modules.
- The Qualcomm driver(s) can now be built as modules.
Incremental improvements:
- The Intel driver now supports pin configuration for GPIO-related
configurations.
- A bunch of Renesas PFC drivers have been augmented with support
for QSPI pins, groups and functions.
- Non-critical fixes to the irq handling in the Allwinner Sunxi
driver.
-----BEGIN PGP SIGNATURE-----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=e5sV
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes for the v5.11 kernel.
Drivers, drivers and drivers. Not a single core change.
Some new stuff, especially a bunch of new Intel, Qualcomm and Ocelot
SoCs.
As part of the modularization attempt, I applied one patch affecting
the firmware subsystem as a functional (not syntactic/semantic)
dependency and then it blew up in our face, so I had to revert it,
bummer. It will come in later, through that subsystem, I guess.
New drivers:
- New driver for the Microchip Serial GPIO "SGPIO".
- Qualcomm SM8250 LPASS (Low Power Audio Subsystem) GPIO driver.
New subdrivers:
- Intel Lakefield subdriver.
- Intel Elkhart Lake subdriver.
- Intel Alder Lake-S subdriver.
- Qualcomm MSM8953 subdriver.
- Qualcomm SDX55 subdriver.
- Qualcomm SDX55 PMIC subdriver.
- Ocelot Luton SoC subdriver.
- Ocelot Serval SoC subdriver.
Modularization:
- The Meson driver can now be built as modules.
- The Qualcomm driver(s) can now be built as modules.
Incremental improvements:
- The Intel driver now supports pin configuration for GPIO-related
configurations.
- A bunch of Renesas PFC drivers have been augmented with support for
QSPI pins, groups and functions.
- Non-critical fixes to the irq handling in the Allwinner Sunxi
driver"
* tag 'pinctrl-v5.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (80 commits)
pinctrl/spear: simplify the return expression of spear300_pinctrl_probe()
pinctrl: mediatek: simplify the return expression of mtk_pinconf_bias_disable_set_rev1()
dt-bindings: pinctrl: pinctrl-microchip-sgpio: Add irq support
pinctrl: pinctrl-microchip-sgpio: Add irq support (for sparx5)
pinctrl: qcom: Add sm8250 lpass lpi pinctrl driver
dt-bindings: pinctrl: qcom: Add sm8250 lpass lpi pinctrl bindings
pinctrl: qcom-pmic-gpio: Add support for pmx55
dt-bindings: pinctrl: qcom-pmic-gpio: Add pmx55 support
pinctrl: pinctrl-microchip-sgpio: Mark some symbols with static keyword
pinctrl: at91-pio4: Make PINCTRL_AT91PIO4 depend on HAS_IOMEM to fix build error
pinctrl: mtk: Fix low level output voltage issue
pinctrl: falcon: add missing put_device() call in pinctrl_falcon_probe()
pinctrl: actions: pinctrl-s500: Constify s500_padinfo[]
pinctrl: pinctrl-microchip-sgpio: Add OF config dependency
pinctrl: pinctrl-microchip-sgpio: Add pinctrl driver for Microsemi Serial GPIO
dt-bindings: pinctrl: Add bindings for pinctrl-microchip-sgpio driver
pinctrl: at91-pio4: add support for fewer lines on last PIO bank
pinctrl: sunxi: Always call chained_irq_{enter, exit} in sunxi_pinctrl_irq_handler
pinctrl: sunxi: Mark the irq bank not found in sunxi_pinctrl_irq_handler() with WARN_ON
pinctrl: sunxi: fix irq bank map for the Allwinner A100 pin controller
...
Here is the big staging and IIO driver pull request for 5.11-rc1
Lots of different things in here:
- loads of driver updates
- so many coding style cleanups
- new IIO drivers
- Android ION code is finally removed from the tree
- wimax drivers are moved to staging on their way out of the kernel
Nothing really exciting, just the constant grind of kernel development :)
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCX9iCdw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+yn44QCguVCsIkhxYmnuTAkrPQP74CbJoJwAoLVoPM5K
LJRbMYjGfRc4gZehlrIV
=clR4
-----END PGP SIGNATURE-----
Merge tag 'staging-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging / IIO driver updates from Greg KH:
"Here is the big staging and IIO driver pull request for 5.11-rc1
Lots of different things in here:
- loads of driver updates
- so many coding style cleanups
- new IIO drivers
- Android ION code is finally removed from the tree
- wimax drivers are moved to staging on their way out of the kernel
Nothing really exciting, just the constant grind of kernel development :)
All have been in linux-next for a while with no reported issues"
* tag 'staging-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (341 commits)
staging: olpc_dcon: Do not call platform_device_unregister() in dcon_probe()
staging: most: Fix spelling mistake "tranceiver" -> "transceiver"
staging: qlge: remove duplicate word in comment
staging: comedi: mf6x4: Fix AI end-of-conversion detection
staging: greybus: Add TODO item about modernizing the pwm code
pinctrl: ralink: add a pinctrl driver for the rt2880 family
dt-bindings: pinctrl: rt2880: add binding document
staging: rtl8723bs: remove ELEMENT_ID enum
staging: rtl8723bs: remove unused macros
staging: rtl8723bs: replace EID_EXTCapability
staging: rtl8723bs: replace EID_BSSIntolerantChlReport
staging: rtl8723bs: replace EID_BSSCoexistence
staging: rtl8723bs: replace _MME_IE_
staging: rtl8723bs: replace _WAPI_IE_
staging: rtl8723bs: replace _EXT_SUPPORTEDRATES_IE_
staging: rtl8723bs: replace _ERPINFO_IE_
staging: rtl8723bs: replace _CHLGETXT_IE_
staging: rtl8723bs: replace _COUNTRY_IE_
staging: rtl8723bs: replace _IBSS_PARA_IE_
staging: rtl8723bs: replace _TIM_IE_
...
This adds 'interrupt-controller' features for the signals available on
the Microchip SGPIO controller, however only for controller versions
on the Sparx5 platform (or later).
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20201209142753.683208-2-lars.povlsen@microchip.com
[Select GPIOLIB_IRQCHIP in Kconfig]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Mistakenly the buffers (input and output) become enabled together for a short
period of time during GPIO request. This is problematic, because instead of
initial motive to disable them in the commit af7e3eeb84
("pinctrl: intel: Disable input and output buffer when switching to GPIO"),
the driven value on the pin, which might be used as an IRQ line, brings
firmwares of some touch pads to an awkward state that needs a full power off
to recover. Fix this, as stated in the culprit commit, by disabling the buffers.
Fixes: af7e3eeb84 ("pinctrl: intel: Disable input and output buffer when switching to GPIO")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=210497
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Tested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20201208182403.40435-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These Socs have 1-3 banks of 8-32 gpios. Rather then setting the muxing of each
pin individually, these socs have mux groups that when set will effect 1-N pins.
Pin groups have a 2, 4 or 8 different muxes.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Link: https://lore.kernel.org/r/20201208075523.7060-3-sergio.paracuellos@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 6726fbff19bf ("pinctrl: aspeed: Fix GPI only function problem.")
fixes access to GPIO banks T and U on the AST2600. Both banks contain
input-only pins and the GPIO pin function is named GPITx and GPIUx
respectively. Unfortunately the fix had a negative impact on GPIO banks
D and E for the AST2400 and AST2500 where the GPIO pass-through
functions take similar "GPI"-style names. The net effect on the older
SoCs was that when the GPIO subsystem requested a pin in banks D or E be
muxed for GPIO, they were instead muxed for pass-through mode.
Mistakenly muxing pass-through mode e.g. breaks booting the host on
IBM's Witherspoon (AC922) platform where GPIOE0 is used for FSI.
Further exploit the names in the provided expression structure to
differentiate pass-through from pin-specific GPIO modes.
This follow-up fix gives the expected behaviour for the following tests:
Witherspoon BMC (AST2500):
1. Power-on the Witherspoon host
2. Request GPIOD1 be muxed via /sys/class/gpio/export
3. Request GPIOE1 be muxed via /sys/class/gpio/export
4. Request the balls for GPIOs E2 and E3 be muxed as GPIO pass-through
("GPIE2" mode) via a pinctrl hog in the devicetree
Rainier BMC (AST2600):
5. Request GPIT0 be muxed via /sys/class/gpio/export
6. Request GPIU0 be muxed via /sys/class/gpio/export
Together the tests demonstrate that all three pieces of functionality
(general GPIOs via 1, 2 and 3, input-only GPIOs via 5 and 6, pass-through
mode via 4) operate as desired across old and new SoCs.
Fixes: 9b92f5c51e ("pinctrl: aspeed: Fix GPI only function problem.")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Tested-by: Joel Stanley <joel@jms.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Cc: Billy Tsai <billy_tsai@aspeedtech.com>
Cc: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20201126063337.489927-1-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial pinctrl driver to support pin configuration for
LPASS (Low Power Audio SubSystem) LPI (Low Power Island) pinctrl
on SM8250.
This IP is an additional pin control block for Audio Pins on top the
existing SoC Top level pin-controller.
Hardware setup looks like:
TLMM GPIO[146 - 159] --> LPASS LPI GPIO [0 - 13]
This pin controller has some similarities compared to Top level
msm SoC Pin controller like 'each pin belongs to a single group'
and so on. However this one is intended to control only audio
pins in particular, which can not be configured/touched by the
Top level SoC pin controller except setting them as gpios.
Apart from this, slew rate is also available in this block for
certain pins which are connected to SLIMbus or SoundWire Bus.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201202163443.26499-3-srinivas.kandagatla@linaro.org
[Add some dependencies]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Fix the following sparse warnings:
drivers/pinctrl/pinctrl-microchip-sgpio.c:63:31: warning: symbol 'properties_luton' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:68:31: warning: symbol 'properties_ocelot' was not declared. Should it be static?
drivers/pinctrl/pinctrl-microchip-sgpio.c:73:31: warning: symbol 'properties_sparx5' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1606218173-3722-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If CONFIG_HAS_IOMEM is not set, devm_platform_ioremap_resource() will
be not built in drivers/base/platform.c and then there exists a build
error about undefined reference to "devm_platform_ioremap_resource"
in pinctrl-at91-pio4.c under COMPILE_TEST and CONFIG_PINCTRL_AT91PIO4,
make PINCTRL_AT91PIO4 depend on HAS_IOMEM to fix it.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Tiezhu Yang <yangtiezhu@loongson.cn>
Link: https://lore.kernel.org/r/1606209423-4742-1-git-send-email-yangtiezhu@loongson.cn
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch is used to fix low level output voltage issue.
A pin is changed from input pull-up to output high.
The Dout value of the pin is default as 0.
If we change the direction of the pin before the dout value of the pin,
It maybe produce a low level output voltage between "input pull-up" and
"output high".
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Link: https://lore.kernel.org/r/20201120093058.7248-2-zhiyong.tao@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
if of_find_device_by_node() succeed, pinctrl_falcon_probe() doesn't have
a corresponding put_device(). Thus add put_device() to fix the exception
handling for this function implementation.
Fixes: e316cb2b16 ("OF: pinctrl: MIPS: lantiq: adds support for FALCON SoC")
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Link: https://lore.kernel.org/r/20201119011219.2248232-1-yukuai3@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
s500_padinfo[] is never modified and should be made 'const' to allow
the compiler to optimize code generation, i.e. put it in the text
section instead of the data section.
Before:
text data bss dec hex filename
12503 5088 0 17591 44b7 drivers/pinctrl/actions/pinctrl-s500.o
After:
text data bss dec hex filename
14435 3156 0 17591 44b7 drivers/pinctrl/actions/pinctrl-s500.o
Signed-off-by: Cristian Ciocaltea <cristian.ciocaltea@gmail.com>
Link: https://lore.kernel.org/r/24505deb08d050eb4ce38f186f4037d7541ea217.1605722628.git.cristian.ciocaltea@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The pinctrl-microchip-sgpio driver needs OF support, so add that to
Kconfig.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20201125122014.11237-1-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds a pinctrl driver for the Microsemi/Microchip Serial GPIO
(SGPIO) device used in various SoC's.
The driver is added as a pinctrl driver, albeit only having just GPIO
support currently. The hardware supports other functions that will be
added following.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20201113145151.68900-3-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Only a cleanup of unneeded breaks.
-----BEGIN PGP SIGNATURE-----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=wzy/
-----END PGP SIGNATURE-----
Merge tag 'samsung-pinctrl-5.11' of https://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/samsung into devel
Samsung pinctrl drivers changes for v5.11
Only a cleanup of unneeded breaks.
- Add QSPI pin groups on R-Car E3, H3, M3-W/W+, and M3-N,
- A small fix for a Clang warning.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX8D/lAAKCRCKwlD9ZEnx
cLu+APwPXWg+/eDeGMft7GROw5SbCxhYcB8Gaouno7oYY7Z6mAD/cC9TJXrdZKV2
dRsTFT3bSyQD8iSVd+J/4AcqmoTHHQM=
=TRxU
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.11-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.11 (take two)
- Add QSPI pin groups on R-Car E3, H3, M3-W/W+, and M3-N,
- A small fix for a Clang warning.
Some products, like sama7g5, do not have a full last bank of PIO lines.
In this case for example, sama7g5 only has 8 lines for the PE bank.
PA0-31, PB0-31, PC0-31, PD0-31, PE0-7, in total 136 lines.
To cope with this situation, added a data attribute that is product dependent,
to specify the number of lines of the last bank.
In case this number is different from the macro ATMEL_PIO_NPINS_PER_BANK,
adjust the total number of lines accordingly.
This will avoid advertising 160 lines instead of the actual 136, as this
product supports, and to avoid reading/writing to invalid register addresses.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20201113132429.420940-1-eugen.hristev@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Add Intel Alder Lake-S pin controller support
* Add Intel Elkhart Lake pin controller support
* Add Intel Lakefield driver pin controller support
* Miscellaneous fixes for Intel Lynxpoint driver
The following is an automated git shortlog grouped by driver:
intel:
- Add Intel Alder Lake-S pin controller support
- Add Intel Elkhart Lake pin controller support
- Add blank line before endif in Kconfig
- Add Intel Lakefield pin controller support
lynxpoint:
- Enable pin configuration setting for GPIO chip
- Use defined constant for disabled bias explicitly
- Unify initcall location in the code
-----BEGIN PGP SIGNATURE-----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=e2B8
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.11-1' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.11-1
* Add Intel Alder Lake-S pin controller support
* Add Intel Elkhart Lake pin controller support
* Add Intel Lakefield driver pin controller support
* Miscellaneous fixes for Intel Lynxpoint driver
The following is an automated git shortlog grouped by driver:
intel:
- Add Intel Alder Lake-S pin controller support
- Add Intel Elkhart Lake pin controller support
- Add blank line before endif in Kconfig
- Add Intel Lakefield pin controller support
lynxpoint:
- Enable pin configuration setting for GPIO chip
- Use defined constant for disabled bias explicitly
- Unify initcall location in the code
It is found on many allwinner soc that there is a low probability that
the interrupt status cannot be read in sunxi_pinctrl_irq_handler. This
will cause the interrupt status of a gpio bank to always be active on
gic, preventing gic from responding to other spi interrupts correctly.
So we should call the chained_irq_* each time enter sunxi_pinctrl_irq_handler().
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/85263ce8b058e80cea25c6ad6383eb256ce96cc8.1604988979.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The interrupt descriptor cannot be found in the interrupt processing
function, and this situation cannot happen when the system is running
normally. It doesn't seem right to return directly to the status of not
handling gic. In this case, it must be a bug, let's mark it with
WARN_ON.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Link: https://lore.kernel.org/r/470ebae22fc5434ad5409c4f6e29255467b3cef6.1604988979.git.frank@allwinnertech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One fixup following my patch commit be117ca322 ("pinctrl:
qcom: Kconfig: Rework PINCTRL_MSM to be a depenency rather then
a selected config") being queued in LinusW's tree, as a new
config entry was added for the msm8953 that also needs the
change.
Applies to LinusW's pinctrl devel tree.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Prasad Sodagudi <psodagud@codeaurora.org>
Cc: Vladimir Lypak <junak.pub@gmail.com>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20201110215619.86076-1-john.stultz@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Fix HOSTSW_OWN offset and unhide SPI group of pins on Jasper Lake
* Fix debounce configuration on Baytrail when it's turned off
* Fix default bias setting on Merrifield
The following is an automated git shortlog grouped by driver:
baytrail:
- Avoid clearing debounce value when turning it off
jasperlake:
- Fix HOSTSW_OWN offset
- Unhide SPI group of pins
merrifield:
- Set default bias in case no particular value given
-----BEGIN PGP SIGNATURE-----
iQIzBAABCgAdFiEEqaflIX74DDDzMJJtb7wzTHR8rCgFAl+yno0ACgkQb7wzTHR8
rChXdxAAw027fWAiA8fDZPri4ZWcvL4QFJB58phUBRayu8ARrOdF0V4xGW4EWKEL
HrMTsB0RFFL5hm0PhWz0vkcoaGGTfe0mJ7Gvbp+x1Kx17ELWQaUS7KOor3omzp48
hwdrU4np4F8GJ4qJb/sbatk22QDFA4sgtTjMrn2exir/3IVBFp3+1wybjn9Zdm/E
m+f3ah7PMpFKyUj+n4gUd2miCYie9FYySbu2FWwqegPdUOmd02j5EWTGOKqw+GmQ
XhNHV7nlMdeyxds5QNtSTGipvIq/+gYXji4FtO5O6DEM72k53hrDlPm0qQjNOdg6
Q3UlorVI5mJfWeaoTFgq9m2ccHM/fTTAEqo3sYmgXD7Ukwd1XTPZPG+od7WPpqDM
NufGv4MGcVIH/mK6kVCUC4gRIA6ahGkokQUCgf+YBH4VBYOh5XBzOlV555+BUGdM
Uj0ANNC3A+AnQiRjo0odVlVrqz+zfBeDLatI7NXoweg3r1L1d7EhwrK7dvCW8yEb
3fEIh0ZUILwEgHg3k++hKvaz7200ON58sRKNwuQJpv75V2GNbj8EVsK+rSoZRrZW
TASXBiXkzxFa3/KGeEpDtD+96goGE9nlcmA2NX21SCB37XbR1OB+zl6n4WRW4xBt
nRHH8GAbZ6j3NSGgNi80I7jZdjpXfjPtdTElJeGR/2L8v/RT3Y4=
=xymw
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.10-3' of gitolite.kernel.org:pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.10-3
* Fix HOSTSW_OWN offset and unhide SPI group of pins on Jasper Lake
* Fix debounce configuration on Baytrail when it's turned off
* Fix default bias setting on Merrifield
The following is an automated git shortlog grouped by driver:
baytrail:
- Avoid clearing debounce value when turning it off
jasperlake:
- Fix HOSTSW_OWN offset
- Unhide SPI group of pins
merrifield:
- Set default bias in case no particular value given
Since commit 4b563a0666 ("ARM: imx: Remove imx21 support") the imx21
SoC is no longer supported.
Get rid of its pinctrl driver too, which is now unused.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Acked-by: Shawn Guo <shawnguo@kernel.org>
Link: https://lore.kernel.org/r/20201110190210.29376-1-festevam@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
- Add remaining video-in (VIN) pin groups on R-Car H2 and RZ/G1H,
- Image size optimizations and code consolidations,
- Minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX66aYQAKCRCKwlD9ZEnx
cHHrAP9V86MzOAHZN0Uixr/onKQtmxdy0s4JLM4HLOh1oxo9VQD/R40pMVz//WWc
tmgfV3UMUq7RyhF11Wqe+d0eAegKogk=
=Qqks
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.11-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.11
- Add remaining video-in (VIN) pin groups on R-Car H2 and RZ/G1H,
- Image size optimizations and code consolidations,
- Minor fixes and improvements.
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
GPIOs that attempt to use interrupts get thwarted with a message like:
"pin 161 cannot be used as IRQ" (for instance with SD_CD). This is because
the HOSTSW_OWN offset is incorrect, so every GPIO looks like it's
owned by ACPI.
Fixes: e278dcb704 ("pinctrl: intel: Add Intel Jasper Lake pin controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Evan Green <evgreen@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If the group of pins is hidden in the pin list it affects
the register offset calculation despite fixed GPIO base.
Hence, the offsets of all pins after the hidden group
are broken. Instead we have to unhide the group and use a flag
to exclude it from GPIO number space.
Fixes: e278dcb704 ("pinctrl: intel: Add Intel Jasper Lake pin controller support")
Reported-by: Divagar Mohandass <divagar.mohandass@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Baytrail pin control has a common register to set up debounce timeout.
When a pin configuration requested debounce to be disabled, the rest
of the pins may still want to have debounce enabled and thus rely on
the common timeout value. Avoid clearing debounce value when turning
it off for one pin while others may still use it.
Fixes: 658b476c74 ("pinctrl: baytrail: Add debounce configuration")
Depends-on: 04ff5a095d ("pinctrl: baytrail: Rectify debounce support")
Depends-on: 827e1579e1 ("pinctrl: baytrail: Rectify debounce support (part 2)")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The only usage of sh73a0_vccq_mc0_ops is to assign its address to the
ops field in the regulator_desc struct, which is a const pointer. Make
it const to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20201109221012.177478-1-rikard.falkeborn@gmail.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
On SuperH and ARM SH/R-Mobile SoCs, the pin control driver handles
GPIOs, too. To reduce code size when compiling a kernel supporting only
modern SoCs, most, but not all, of the GPIO functionality is protected
by checks for CONFIG_PINCTRL_SH_FUNC_GPIO.
Factor out the remaining parts when not needed:
1. sh_pfc_soc_info.{in,out}put describe GPIO pins that have input
resp. output capabilities (SuperH and SH/R-Mobile).
2. sh_pfc_soc_info.gpio_irq{,_size} describe the mapping from GPIO
pins to interrupt numbers (SH/R-Mobile).
3. sh_pfc_gpio_set_direction() configures GPIO direction, called from
the GPIO driver through pinctrl_gpio_direction_{in,out}put()
(SH/R-Mobile). Unfortunately this function cannot just be moved to
drivers/pinctrl/renesas/gpio.c, as it relies on knowledge of
sh_pfc_pinctrl, which is internal to
drivers/pinctrl/renesas/pinctrl.c.
While code size reduction is minimal, this does help in documenting
depencies.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-9-geert+renesas@glider.be
Currently, the rcar_pinmux_[gs]et_bias() helpers handle only SoCs that
have separate LSI Pin Pull-Enable (PUEN) and Pull-Up/Down Control (PUD)
registers, like R-Car Gen3 and RZ/G2. Update the function to handle
SoCs that have only LSI Pin Pull-Up Control Register (PUPR), like R-Car
Gen1/Gen2 and RZ/G1.
Reduce code duplication by converting the R-Car M1A pin control driver
to use the common handler.
Note that this changes behavior in case the (invalid!) option
"bias-pull-down" is used in an R-Car M1A DTS: before, it was ignored
silently; after this change, it is considered the same as
"bias-pull-up".
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-8-geert+renesas@glider.be
The handling of the LSI Pin Pull-Up Control Registers (PUPR) on R-Car
M1A uses register offsets instead of register physical addresses.
This is different from the handling on other R-Car parts.
Convert the bias handling from register offsets to physical addresses.
This increases uniformity, and prepares for consolidation of the bias
handling.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-7-geert+renesas@glider.be
Shrink sh_pfc_pin_config from 8 to 2 bytes:
- The mux_set flag can be removed, as a non-zero mark value means the
same (zero = PINMUX_RESERVED is an invalid mark value),
- The gpio_enabled flag needs only a single bit,
- Mark values are small integers, and can easily fit in a 15-bit
bitfield.
This saves 6 bytes per pin when allocating the sh_pfc_pinctrl.configs
array, i.e. it reduces run-time memory consumption by ca. 1.5 KiB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-5-geert+renesas@glider.be
On arm64, pointer size and alignment is 64-bit, hence a 4-byte hole is
present in between the enum_id and name members of the sh_pfc_pin
structure. Get rid of this hole by sorting the structure's members by
decreasing size.
This saves up to 1.5 KiB per enabled SoC, and reduces the size of a
kernel including support for all R-Car Gen3 SoCs by more than 10 KiB.
This has no size impact on SH and arm32.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20201028151637.1734130-4-geert+renesas@glider.be
This driver supports both RZ/G1[MN] and R-Car M2-W/M2-N SoCs.
Optimize pinctrl image size for RZ/G1[MN], when support for R-Car
M2-W/M2-N (R8A779[13]) is not enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201019124258.4574-7-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This driver supports both RZ/G1H and R-Car H2 SoCs.
Optimize pinctrl image size for RZ/G1H, when support for R-Car H2
(R8A7790) is not enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201019124258.4574-6-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This driver supports both RZ/G2E and R-Car E3 SoCs.
Optimize pinctrl image size for RZ/G2E, when support for R-Car E3
(R8A77990) is not enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201019124258.4574-5-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This driver supports both RZ/G2N and R-Car M3-N SoCs.
Optimize pinctrl image size for RZ/G2N, when support for R-Car M3-N
(R8A77965) is not enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201019124258.4574-4-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This driver supports both RZ/G2M and R-Car M3-W/W+ SoCs.
Optimize pinctrl image size for RZ/G2M, when support for R-Car M3-W/W+
(R8A7796[01]) is not enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201019132805.5996-1-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
This driver supports both RZ/G2H and R-Car H3 ES2 SoCs.
Optimize pinctrl image size for RZ/G2H, when support for R-Car H3 ES2
(R8A77951) is not enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20201019124258.4574-2-biju.das.jz@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel Merrifield pin control hardware the 20 kOhm sounds plausible
because it gives a good trade off between weakness and minimization of leakage
current (will be only 50 uA with the above choice).
Fixes: 4e80c8f505 ("pinctrl: intel: Add Intel Merrifield pin controller support")
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
GPIOs that attempt to use interrupts get thwarted with a message like:
"pin 161 cannot be used as IRQ" (for instance with SD_CD). This is because
the HOSTSW_OWN offset is incorrect, so every GPIO looks like it's
owned by ACPI.
Fixes: e278dcb704 ("pinctrl: intel: Add Intel Jasper Lake pin controller support")
Cc: stable@vger.kernel.org
Signed-off-by: Evan Green <evgreen@chromium.org>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
If the group of pins is hidden in the pin list it affects
the register offset calculation despite fixed GPIO base.
Hence, the offsets of all pins after the hidden group
are broken. Instead we have to unhide the group and use a flag
to exclude it from GPIO number space.
Fixes: e278dcb704 ("pinctrl: intel: Add Intel Jasper Lake pin controller support")
Reported-by: Divagar Mohandass <divagar.mohandass@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
It appears that pin configuration for GPIO chip hasn't been enabled yet
due to absence of ->set_config() callback.
Enable it here for Intel Lynxpoint PCH.
Depends-on: 2956b5d94a ("pinctrl / gpio: Introduce .set_config() callback for GPIO chips")
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
We have a specific constant to describe a disabled bias,
i.e. GPIWP_NONE. Use it explicitly instead of making
an assumption about its value.
While at it, move argument assignment to the switch-case
in lp_pin_config_get().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Replace the two separate calls for setting the irq handler and data with a
single irq_set_chained_handler_and_data() call.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Link: https://lore.kernel.org/r/20201108180144.28594-1-martin@kaiser.cx
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Commit be117ca322 ("pinctrl: qcom: Kconfig: Rework PINCTRL_MSM to be a
dependency rather then a selected config") moved the qcom pinctrl drivers
to have PINCTRL_MSM as dependency rather then a selected config, so do
this change for SDX55 pinctrl driver as well.
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201111043610.177168-1-vkoul@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need a more granular distribution among funcion A
and function B for the LCD pins for the Samsung
GT-I9070. Provide some new pin groups so we can
configure this phone properly.
Link: https://lore.kernel.org/r/20201110232330.2242167-1-linus.walleij@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Respect bias setting when comes from ACPI
The following is an automated git shortlog grouped by driver:
intel:
- Set default bias in case no particular value given
- Fix 2 kOhm bias which is 833 Ohm
-----BEGIN PGP SIGNATURE-----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=Voi9
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.10-2' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into fixes
intel-pinctrl for v5.10-2
* Respect bias setting when comes from ACPI
The following is an automated git shortlog grouped by driver:
intel:
- Set default bias in case no particular value given
- Fix 2 kOhm bias which is 833 Ohm
This patch adds support for Serval pinctrl, using the ocelot driver as
basis. It adds pinconfig support as well, as supported by the
platform.
gclement: Split from a larger patch adding support all platforms in
the same time.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20201106093118.965152-5-gregory.clement@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for Luton pinctrl, using the ocelot driver as
basis. It adds pinconfig support as well, as supported by the
platform.
gclement: Split from a larger patch adding support all platforms in
the same time.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20201106093118.965152-4-gregory.clement@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Tweaks to allow pinctrl-msm code to be loadable as a module.
This is needed in order to support having the qcom-scm driver,
which pinctrl-msm calls into, configured as a module.
This requires that we tweak Kconfigs selecting PINCTRL_MSM to
also depend on QCOM_SCM || QCOM_SCM=n so that we match the
module setting of QCOM_SCM.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20201106042710.55979-2-john.stultz@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch reworks PINCTRL_MSM to be a visible option, and
instead of having the various SoC specific drivers select
PINCTRL_MSM, this switches those configs to depend on
PINCTRL_MSM.
This is useful, as it will be needed in order to cleanly support
having the qcom-scm driver, which pinctrl-msm calls into,
configured as a module. Without this change, we would eventually
have to add dependency lines to every config that selects
PINCTRL_MSM, and that would becomes a maintenance headache.
We also add PINCTRL_MSM to the arm64 defconfig to avoid
surprises as otherwise PINCTRL_MSM/IPQ* options previously
enabled, will be off.
Signed-off-by: John Stultz <john.stultz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jason Cooper <jason@lakedaemon.net>
Cc: Marc Zyngier <maz@kernel.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Vinod Koul <vkoul@kernel.org>
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: Maulik Shah <mkshah@codeaurora.org>
Cc: Lina Iyer <ilina@codeaurora.org>
Cc: Saravana Kannan <saravanak@google.com>
Cc: Todd Kjos <tkjos@google.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-msm@vger.kernel.org
Cc: iommu@lists.linux-foundation.org
Cc: linux-gpio@vger.kernel.org
Link: https://lore.kernel.org/r/20201106042710.55979-1-john.stultz@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Print the status of debounce filter as follows,
$ cat /sys/kernel/debug/gpio
pin129 interrupt is disabled | interrupt is masked |
disable wakeup in S0i3 state | disable wakeup in S3 state |
disable wakeup in S4/S5 state| input is high | pull-up is disabled |
Pull-down is disabled | output is disabled |
debouncing filter disabled | 0x50000
pin130 interrupt is disabled | interrupt is masked |
disable wakeup in S0i3 state | disable wakeup in S3 state |
disable wakeup in S4/S5 state | input is high | pull-up is disabled |
Pull-down is disabled | output is disabled |
debouncing filter (high) enabled |
debouncing timeout is 124800 (us)| 0x503c8
Signed-off-by: Coiby Xu <coiby.xu@gmail.com>
Link: https://lore.kernel.org/r/20201105231912.69527-4-coiby.xu@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add the "lcd-8bit" group to the "lcd" function.
As "lcd-24bit" is a superset of "lcd-8bit", in theory the former could
be modified to only contain the pins not already included in "lcd-8bit",
just like how it's done for the JZ4740 and JZ4725B platforms. However,
we can't do that without breaking Device Tree ABI, so in that case we
have no choice but to have two groups containing the same pins.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20201101090104.5088-3-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Abuse the pin function pointer to store the pin function value directly,
when all the pins of a group have the same function value. Now when the
pointer value is <= 3 (unsigned), the pointer value is used as the pin
function; otherwise it is used as a regular pointer.
This drastically reduces the number of pin function tables needed, and
drops .data usage by about 2 KiB. Additionally, the few pin function
tables that are still around now contain u8 instead of int, since the
largest number that will be stored is 3.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Tested-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20201101090104.5088-2-paul@crapouillou.net
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
mt7622 is reported by mediatek to have only 6 pwm channels
so drop pindefines for 7th channel
Signed-off-by: Frank Wunderlich <frank-w@public-files.de>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/20201016204019.2606-4-linux@fw-web.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Specify the PDC mapping for SM8250, so that gpio interrupts are
propertly mapped to the wakeup IRQs of the PDC.
Fixes: 4e3ec9e407 ("pinctrl: qcom: Add sm8250 pinctrl driver.")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201028043642.1141723-1-bjorn.andersson@linaro.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When GPIOs that are routed to PDC are used as output they can still latch
the IRQ pending at GIC. As a result the spurious IRQ was handled when the
client driver change the direction to input to starts using it as IRQ.
Currently such erroneous latched IRQ are cleared with .irq_enable callback
however if the driver continue to use GPIO as interrupt and invokes
disable_irq() followed by enable_irq() then everytime during enable_irq()
previously latched interrupt gets cleared.
This can make edge IRQs not seen after enable_irq() if they had arrived
after the driver has invoked disable_irq() and were pending at GIC.
Move clearing erroneous IRQ to .irq_request_resources callback as this is
the place where GPIO direction is changed as input and its locked as IRQ.
While at this add a missing check to invoke msm_gpio_irq_clear_unmask()
from .irq_enable callback only when GPIO is not routed to PDC.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Link: https://lore.kernel.org/r/1604561884-10166-1-git-send-email-mkshah@codeaurora.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
RTC is 32.768kHz thus 512 RtcClk equals 15625 usec. The documentation
likely has dropped precision and that's why the driver mistakenly took
the slightly deviated value.
Cc: stable@vger.kernel.org
Reported-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Suggested-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Coiby Xu <coiby.xu@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/linux-gpio/2f4706a1-502f-75f0-9596-cc25b4933b6c@redhat.com/
Link: https://lore.kernel.org/r/20201105231912.69527-3-coiby.xu@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some gpio pin at aspeed soc is input only and the prefix name of these
pin is "GPI" only.
This patch fine-tune the condition of GPIO check from "GPIO" to "GPI"
and it will fix the usage error of banks D and E in the AST2400/AST2500
and banks T and U in the AST2600.
Fixes: 4d3d0e4272 ("pinctrl: Add core support for Aspeed SoCs")
Signed-off-by: Billy Tsai <billy_tsai@aspeedtech.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20201030055450.29613-1-billy_tsai@aspeedtech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Enable pinctrl drivers for 64-bit Amlogic SoCs to be built as modules.
The default is still built-in, this only adds the option of building
as modules.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Link: https://lore.kernel.org/r/20201026183025.31768-1-khilman@baylibre.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It is useful for debugging to have the error message printed
when regmap initialisation fails. Add it to the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20201009180856.4738-2-andriy.shevchenko@linux.intel.com
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that simplification of mcp23s08_spi_regmap_init() made
a regression due to wrong size calculation for dev_kmemdup() call.
It misses the fact that config variable is already a pointer, thus
the sizeof() calculation is wrong and only 4 or 8 bytes were copied.
Fix the parameters to devm_kmemdup() to copy a full chunk of memory.
Fixes: 0874758ecb ("pinctrl: mcp23s08: Refactor mcp23s08_spi_regmap_init()")
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Martin Hundebøll <martin@geanix.com>
Link: https://lore.kernel.org/r/20201009180856.4738-1-andriy.shevchenko@linux.intel.com
Tested-by: Jan Kundrát <jan.kundrat@cesnet.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Remove totally irq mappings create in probe, the gpio irq mapping will
be created when do
gpio_to_irq ->
rockchip_gpio_to_irq ->
irq_create_mapping
This patch can speed up system boot on, also abandon many unused irq
mappings' create.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20201013063731.3618-4-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
There need to enable pclk_gpio when do irq_create_mapping, since it will
do access to gpio controller.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Kever Yang<kever.yang@rock-chips.com>
Link: https://lore.kernel.org/r/20201013063731.3618-3-jay.xu@rock-chips.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Like in the other Intel pin control drivers, attach initcalls
to the corresponding functions. No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This driver adds pinctrl/GPIO support for Intel Alder Lake-S SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This driver adds pinctrl/GPIO support for Intel Elkhart Lake SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add a blank line before endif directive in Kconfig for better readability.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This driver adds pinctrl/GPIO support for Intel Lakefield SoC. The
GPIO controller is based on the next generation GPIO hardware but still
compatible with the one supported by the Intel core pinctrl/GPIO driver.
Cc: Ricardo Neri <ricardo.neri-calderon@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
The values for the SSI pins on GPIO chips D and E were off by 0x20.
Fixes: d3ef8c6b22 ("pinctrl: Ingenic: Add SSI pins support for JZ4770 and JZ4780.")
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reported-by: Artur Rojek <contact@artur-rojek.eu>
Link: https://lore.kernel.org/r/20201010192509.9098-1-paul@crapouillou.net
Reviewed-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When GPIO library asks pin control to set the bias, it doesn't pass
any value of it and argument is considered boolean (and this is true
for ACPI GpioIo() / GpioInt() resources, by the way). Thus, individual
drivers must behave well, when they got the resistance value of 1 Ohm,
i.e. transforming it to sane default.
In case of Intel pin control hardware the 5 kOhm sounds plausible
because on one hand it's a minimum of resistors present in all
hardware generations and at the same time it's high enough to minimize
leakage current (will be only 200 uA with the above choice).
Fixes: e57725eabf ("pinctrl: intel: Add support for hardware debouncer")
Reported-by: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
2 kOhm bias was never an option in Intel GPIO hardware, the available
matrix is:
000 none
001 1 kOhm (if available)
010 5 kOhm
100 20 kOhm
As easy to get the 3 resistors are gated separately and according to
parallel circuits calculations we may get combinations of the above where
the result is always strictly less than minimal resistance. Hence,
additional values can be:
011 ~833.3 Ohm
101 ~952.4 Ohm
110 ~4 kOhm
111 ~800 Ohm
That said, convert TERM definitions to be the bit masks to reflect the above.
While at it, enable the same setting for pull down case.
Fixes: 7981c0015a ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Cc: Jamie McClymont <jamie@kwiius.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Add pins, groups and functions for the VIN1-B [data/sync/field/clkenb/clk]
and VIN2-G8.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Link: https://lore.kernel.org/r/20200917195924.20384-1-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Core changes:
- NONE whatsoever, we don't even touch the core files this
time around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and
groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile
drivers.
- The "SH-PFC" (literally SuperH pin function controller, I
think) subdirectory is now renamed to the more neutral
"renesas", as these are not very much centered around
SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver.
-----BEGIN PGP SIGNATURE-----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=TdjX
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"Core changes:
- NONE whatsoever, we don't even touch the core files this time
around.
New drivers:
- New driver for the Toshiba Visconti SoC.
- New subdriver for the Qualcomm MSM8226 SoC.
- New subdriver for the Actions Semiconductor S500 SoC.
- New subdriver for the Mediatek MT8192 SoC.
- New subdriver for the Microchip SAMA7G5 SoC.
Driver enhancements:
- Intel Cherryview and Baytrail cleanups and refactorings.
- Enhanced support for the Renesas R8A7790, more pins and groups.
- Some optimizations for the MCP23S08 MCP23x17 variant.
- Some cleanups around the Actions Semiconductor subdrivers.
- A bunch of cleanups around the SH-PFC and Emma Mobile drivers.
- The "SH-PFC" (literally SuperH pin function controller, I think)
subdirectory is now renamed to the more neutral "renesas", as these
are not very much centered around SuperH anymore.
- Non-critical fixes for the Aspeed driver.
- Non-critical fixes for the Ingenic (MIPS!) driver.
- Fix a bunch of missing pins on the AMD pinctrl driver"
* tag 'pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (78 commits)
pinctrl: amd: Add missing pins to the pin group list
dt-bindings: pinctrl: sunxi: Allow pinctrl with more interrupt banks
pinctrl: visconti: PINCTRL_TMPV7700 should depend on ARCH_VISCONTI
pinctrl: mediatek: Free eint data on failure
pinctrl: single: fix debug output when #pinctrl-cells = 2
pinctrl: single: fix pinctrl_spec.args_count bounds check
pinctrl: sunrisepoint: Modify COMMUNITY macros to be consistent
pinctrl: cannonlake: Modify COMMUNITY macros to be consistent
pinctrl: tigerlake: Fix register offsets for TGL-H variant
pinctrl: Document pinctrl-single,pins when #pinctrl-cells = 2
pinctrl: mediatek: use devm_platform_ioremap_resource_byname()
pinctrl: nuvoton: npcm7xx: Constify static ops structs
pinctrl: mediatek: mt7622: add antsel pins/groups
pinctrl: ocelot: simplify the return expression of ocelot_gpiochip_register()
pinctrl: at91-pio4: add support for sama7g5 SoC
dt-bindings: pinctrl: at91-pio4: add microchip,sama7g5
pinctrl: spear: simplify the return expression of tvc_connect()
pinctrl: spear: simplify the return expression of spear310_pinctrl_probe
pinctrl: sprd: use module_platform_driver to simplify the code
pinctrl: Ingenic: Add I2S pins support for Ingenic SoCs.
...
Core changes:
- The big core change is the updated (v2) userspace character
device API. This corrects badly designed 64-bit alignment around
the line events. We also add the debounce request feature.
This echoes the often quotes passage from Frederick Brooks
"The mythical man-month" to always throw one away, which we
have seen before in things such as V4L2. So we put in a new
one and deprecate and obsolete the old one.
- All example tools in tools/gpio/* are migrated to the new API
to set a good example. The libgpiod userspace library has been
augmented to use this new API pretty much from day 1.
- Some misc API hardening by using strn* function calls has been
added as well.
- Use the simpler IDA interface for GPIO chip instance enumeration.
- Add device core function for counting string arrays in
device properties.
- Provide a generic library function kfree_strarray() that can
be used throughout the kernel.
Driver enhancements:
- The DesignWare dwapb-gpio driver has been enhanced and now
uses the IRQ handling in the gpiolib core.
- The mockup and aggregator drivers have seen some substantial
code clean-up and now use more of the core kernel
inftrastructure.
- Misc cleanups using dev_err_probe().
- The MXC drivers (Freescale/NXP) can now be built modularized,
which makes modularized GKI Android kernels happy.
-----BEGIN PGP SIGNATURE-----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=8CE2
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This time very little driver changes but lots of core changes.
We have some interesting cooperative work for ARM and Intel alike,
making the GPIO subsystem more and more suitable for industrial
systems and the like, in addition to the in-kernel users.
We touch driver core (device properties) and lib/* by adding one
simple string array free function, these are authored by Andy
Shevchenko who is a well known and recognized core helpers maintainers
so this should be fine.
We also see some Android GKI-related modularization in the MXC
drivers.
Core changes:
- The big core change is the updated (v2) userspace character device
API.
This corrects badly designed 64-bit alignment around the line
events. We also add the debounce request feature. This echoes the
often quotes passage from Frederick Brooks "The mythical man-month"
to always throw one away, which we have seen before in things such
as V4L2. So we put in a new one and deprecate and obsolete the old
one.
- All example tools in tools/gpio/* are migrated to the new API to
set a good example. The libgpiod userspace library has been
augmented to use this new API pretty much from day 1.
- Some misc API hardening by using strn* function calls has been
added as well.
- Use the simpler IDA interface for GPIO chip instance enumeration.
- Add device core function for counting string arrays in device
properties.
- Provide a generic library function kfree_strarray() that can be
used throughout the kernel.
Driver enhancements:
- The DesignWare dwapb-gpio driver has been enhanced and now uses the
IRQ handling in the gpiolib core.
- The mockup and aggregator drivers have seen some substantial code
clean-up and now use more of the core kernel inftrastructure.
- Misc cleanups using dev_err_probe().
- The MXC drivers (Freescale/NXP) can now be built modularized, which
makes modularized GKI Android kernels happy"
* tag 'gpio-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (73 commits)
gpiolib: Update header block in gpiolib-cdev.h
gpiolib: cdev: switch from kstrdup() to kstrndup()
docs: gpio: add a new document to its index.rst
gpio: pca953x: Add support for the NXP PCAL9554B/C
tools: gpio: add debounce support to gpio-event-mon
tools: gpio: add multi-line monitoring to gpio-event-mon
tools: gpio: port gpio-event-mon to v2 uAPI
tools: gpio: port gpio-hammer to v2 uAPI
tools: gpio: rename nlines to num_lines
tools: gpio: port gpio-watch to v2 uAPI
tools: gpio: port lsgpio to v2 uAPI
gpio: uapi: document uAPI v1 as deprecated
gpiolib: cdev: support setting debounce
gpiolib: cdev: support GPIO_V2_LINE_SET_VALUES_IOCTL
gpiolib: cdev: support GPIO_V2_LINE_SET_CONFIG_IOCTL
gpiolib: cdev: support edge detection for uAPI v2
gpiolib: cdev: support GPIO_V2_GET_LINEINFO_IOCTL and GPIO_V2_GET_LINEINFO_WATCH_IOCTL
gpiolib: cdev: support GPIO_V2_GET_LINE_IOCTL and GPIO_V2_LINE_GET_VALUES_IOCTL
gpiolib: add build option for CDEV v1 ABI
gpiolib: make cdev a build option
...
Core:
- Allow trimming of interrupt hierarchy to support odd hardware setups
where only a subset of the interrupts requires the full hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI PRUSS,
Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the place.
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl+ENDsTHHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoTyXD/9oGq37/zjpCggtRWdTKGtKvndjodqt
82zTZ1eSukDSE3UoT7PL8cRQ/4MnRZ7Ke+Iidd2uUbWADfJN28+4d26wN/aYYlX7
HmI/zowBgK6CJweynHYEF9/C8g2v2SRg5HJCJSOSuVLnTKNLc/aHX5rc/FZXGd6v
K1BOHJFlzoU1w+OnFfoH4TeJdoKhzXi/T5zJFFtadOVIeCONxTEs4Fxkej2cuBsu
Nz38WfkPdOnyrVIPhA10KgigczcRkKXU0ot/bNH4s9j2ZIGdgtq3UIbH+itleW2S
bSWSShnlhSMS918pZNcR49iRyP2CsM+JxcHAmcbA6VPBpKbk2Pb5Zta8g08TZm+X
XxaDwPFoR4BG00B0L4uygEuHcE89mDy0gCFog0zG7sU+LuY4FYQSSMUqwIC4i/HJ
DJdWrVqnNHJFCS6wvBl9NO0lyuUrn2be2/IzUtZ3d0xbA0uJXfvI4WgFrbunoPEU
zgHblQN5nkDLWujjzC10C9vmTi1xxP6FiYcrMScZZ5US0JlHaptkoPOhs82KYQvV
0DPk06XGWnJMc27+MQYVIMDhQggi3It9pgDRhoyz9Xpgn9fmhhp0goL7KnFk9Hbr
BKFdW4VBbU0PZacoI6Q186lTQZRptTKfREL+bHvUL2Xyb0RO6nerBPzE5Wxwb2vW
PmHgFezXDVHbIQ==
=1ewL
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"Updates for the interrupt subsystem:
Core:
- Allow trimming of interrupt hierarchy to support odd hardware
setups where only a subset of the interrupts requires the full
hierarchy.
- Allow the retrigger mechanism to follow a hierarchy to simplify
driver code.
- Provide a mechanism to force enable wakeup interrrupts on suspend.
- More infrastructure to handle IPIs in the core code
Architectures:
- Convert ARM/ARM64 IPI handling to utilize the interrupt core code.
Drivers:
- The usual pile of new interrupt chips (MStar, Actions Owl, TI
PRUSS, Designware ICTL)
- ARM(64) IPI related conversions
- Wakeup support for Qualcom PDC
- Prevent hierarchy corruption in the NVIDIA Tegra driver
- The usual small fixes, improvements and cleanups all over the
place"
* tag 'irq-core-2020-10-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (59 commits)
dt-bindings: interrupt-controller: Add MStar interrupt controller
irqchip/irq-mst: Add MStar interrupt controller support
soc/tegra: pmc: Don't create fake interrupt hierarchy levels
soc/tegra: pmc: Allow optional irq parent callbacks
gpio: tegra186: Allow optional irq parent callbacks
genirq/irqdomain: Allow partial trimming of irq_data hierarchy
irqchip/qcom-pdc: Reset PDC interrupts during init
irqchip/qcom-pdc: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
genirq/PM: Introduce IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag
pinctrl: qcom: Use return value from irq_set_wake() call
pinctrl: qcom: Set IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags
ARM: Handle no IPI being registered in show_ipi_list()
MAINTAINERS: Add entries for Actions Semi Owl SIRQ controller
irqchip: Add Actions Semi Owl SIRQ controller
dt-bindings: interrupt-controller: Add Actions SIRQ controller binding
dt-bindings: dw-apb-ictl: Update binding to describe use as primary interrupt controller
irqchip/dw-apb-ictl: Add primary interrupt controller support
irqchip/dw-apb-ictl: Refactor priot to introducing hierarchical irq domains
genirq: Add stub for set_handle_irq() when !GENERIC_IRQ_MULTI_HANDLER
...
Some of the pins were not exposed in the initial driver or kept as
reserved. Exposing all of them now.
Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Link: https://lore.kernel.org/r/20201007111220.744348-1-Shyam-sundar.S-k@amd.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Toshiba Visconti TMPV7700 series pin controller is only present on
Visconti SoCs. Hence add a dependency on ARCH_VISCONTI, to prevent
asking the user about this driver when configuring a kernel without
Visconti platform support.
Fixes: a68a784426 ("pinctrl: visconti: Add Toshiba Visconti SoCs pinctrl support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
Link: https://lore.kernel.org/r/20201005125049.26926-1-geert+renesas@glider.be
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Set IRQCHIP_ENABLE_WAKEUP_ON_SUSPEND flag to enable/unmask the
wakeirqs during suspend entry.
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-5-git-send-email-mkshah@codeaurora.org
msmgpio irqchip was not using return value of irq_set_irq_wake() callback
since previously GIC-v3 irqchip neither had IRQCHIP_SKIP_SET_WAKE flag nor
it implemented .irq_set_wake callback. This lead to irq_set_irq_wake()
return error -ENXIO.
However from 'commit 4110b5cbb0 ("irqchip/gic-v3: Allow interrupt to be
configured as wake-up sources")' GIC irqchip has IRQCHIP_SKIP_SET_WAKE
flag.
Use return value from irq_set_irq_wake() and irq_chip_set_wake_parent()
instead of always returning success.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-3-git-send-email-mkshah@codeaurora.org
Both IRQCHIP_SET_TYPE_MASKED and IRQCHIP_MASK_ON_SUSPEND flags are already
set for msmgpio's parent PDC irqchip but GPIO interrupts do not get masked
during suspend or during setting irq type since genirq checks irqchip flag
of msmgpio irqchip which forwards these calls to its parent PDC irqchip.
Add irqchip specific flags for msmgpio irqchip to mask non wakeirqs during
suspend and mask before setting irq type. Masking before changing type make
sures any spurious interrupt is not detected during this operation.
Fixes: e35a6ae0eb ("pinctrl/msm: Setup GPIO chip in hierarchy")
Signed-off-by: Maulik Shah <mkshah@codeaurora.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Tested-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/1601267524-20199-2-git-send-email-mkshah@codeaurora.org
The property #pinctrl-cells can either be 1 or 2:
- if #pinctrl-cells = <1>, then pinctrl_spec.args_count = 2
- if #pinctrl-cells = <2>, then pinctrl_spec.args_count = 3
All other values of pinctrl_spec.args_count are incorrect. This fix
checks the upper bound instead of just the lower bound.
Fixes: a133954188 ("pinctrl: single: parse #pinctrl-cells = 2")
Reported-by: Trent Piepho <tpiepho@gmail.com>
Signed-off-by: Drew Fustini <drew@beagleboard.org>
Acked-by: Tony Lindgren <tony@atomide.com>
Link: https://lore.kernel.org/linux-omap/3139716.CMS8C0sQ7x@zen.local/
Link: https://lore.kernel.org/r/20200930174839.1308344-1-drew@beagleboard.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
check mtk_is_virt_gpio input parameter,
virtual gpio need to support eint mode.
add error handler for the ko case
to fix this boot fail:
pc : mtk_is_virt_gpio+0x20/0x38 [pinctrl_mtk_common_v2]
lr : mtk_gpio_get_direction+0x44/0xb0 [pinctrl_paris]
Fixes: edd5464650 ("pinctrl: mediatek: avoid virtual gpio trying to set reg")
Signed-off-by: Hanks Chen <hanks.chen@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Singed-off-by: Jie Yang <sin_jieyang@mediatek.com>
Link: https://lore.kernel.org/r/1597922546-29633-1-git-send-email-hanks.chen@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify COMMUNITY macros to be consistent with Tiger Lake and others.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20200929110306.40852-3-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Modify COMMUNITY macros to be consistent with Tiger Lake and others.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20200929110306.40852-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
It appears that almost traditionally the H variants have some deviations
in the register offsets in comparison to LP ones. This is the case for
Intel Tiger Lake as well. Fix register offsets for TGL-H variant.
Fixes: 653d96455e ("pinctrl: tigerlake: Add support for Tiger Lake-H")
Reported-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20200929110306.40852-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Wang Xiaojun <wangxiaojun11@huawei.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/20200917064151.2184010-1-wangxiaojun11@huawei.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of these structs is to assign their address to various
ops fields in the pinctrl_desc struct, which are const pointers. Make
them const to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Link: https://lore.kernel.org/r/20200926202342.31014-1-rikard.falkeborn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add support for sama7g5 pinctrl block, which has 5 PIO banks.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Reviewed-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Link: https://lore.kernel.org/r/20200917131257.273882-2-eugen.hristev@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When PINCTRL_BCM2835 is enabled and GPIOLIB is disabled, it results in the
following Kbuild warning:
WARNING: unmet direct dependencies detected for GPIOLIB_IRQCHIP
Depends on [n]: GPIOLIB [=n]
Selected by [y]:
- PINCTRL_BCM2835 [=y] && PINCTRL [=y] && OF [=y] && (ARCH_BCM2835 [=n] || ARCH_BRCMSTB [=n] || COMPILE_TEST [=y])
The reason is that PINCTRL_BCM2835 selects GPIOLIB_IRQCHIP without
depending on or selecting GPIOLIB while GPIOLIB_IRQCHIP is subordinate to
GPIOLIB.
Honor the kconfig menu hierarchy to remove kconfig dependency warnings.
Fixes: 85ae9e512f ("pinctrl: bcm2835: switch to GPIOLIB_IRQCHIP")
Signed-off-by: Necip Fazil Yildiran <fazilyildiran@gmail.com>
Link: https://lore.kernel.org/r/20200914144025.371370-1-fazilyildiran@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
1.Add I2S pins support for the JZ4780 SoC.
2.Add I2S pins support for the X1000 SoC.
3.Add I2S pins support for the X1500 SoC.
4.Add I2S pins support for the X1830 SoC.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200913065836.12156-4-zhouyanjie@wanyeetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Correct the pullup and pulldown parameters of JZ4780 to make them
consistent with the parameters on the datasheet.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200913065836.12156-3-zhouyanjie@wanyeetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add SSI pins support for the JZ4770 SoC and the
JZ4780 SoC from Ingenic.
Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Reviewed-by: Paul Cercueil <paul@crapouillou.net>
Link: https://lore.kernel.org/r/20200913065836.12156-2-zhouyanjie@wanyeetech.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
These were skipped in the original patches adding pinconf support for
the AST2600.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Link: https://lore.kernel.org/r/20200910025631.2996342-4-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Aspeed pinconf data structures are split into 'conf' and 'map'
types, where the 'conf' struct defines which register and bitfield to
manipulate, while the 'map' struct defines what value to write to
the register and bitfield.
Both structs have a mask member, and the wrong mask was being used to
tell the regmap which bits to update.
A todo is to look at whether we can remove the mask from the 'map'
struct.
Fixes: 5f52c85384 ("pinctrl: aspeed: Use masks to describe pinconf bitfields")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Cc: Johnny Huang <johnny_huang@aspeedtech.com>
Link: https://lore.kernel.org/r/20200910025631.2996342-3-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
When displaying which pinconf register and field is being touched,
format the field mask so that it's consistent with the way the pinmux
portion formats the mask.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Link: https://lore.kernel.org/r/20200910025631.2996342-2-andrew@aj.id.au
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Change PINCTRL_IMX to tristate to support loadable module build.
And i.MX common pinctrl driver should depend on CONFIG_OF to make sure
no build error when i.MX common pinctrl driver is enabled for different
architectures without CONFIG_OF.
Also add module author, description and license.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1599552721-24872-3-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use function callbacks for SCU related functions in pinctrl-imx.c
in order to support the scenario of PINCTRL_IMX is built in while
PINCTRL_IMX_SCU is built as module, all drivers using SCU pinctrl
driver need to initialize the SCU related function callback, and
no need to check CONFIG_PINCTRL_IMX_SCU anymore, hence stub functions
also can be removed.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Reviewed-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/1599552721-24872-1-git-send-email-Anson.Huang@nxp.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* Add last part of cleanup Cherryview driver to align with other drivers
* Due to above clean up Cherryview and Baytrail drivers to use common API
The following is an automated git shortlog grouped by driver:
baytrail:
- Switch to use intel_pinctrl_get_soc_data()
cherryview:
- Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
- Switch to use intel_pinctrl_get_soc_data()
- Utilize temporary variable to hold device pointer
- Switch to use struct intel_pinctrl
- Move custom community members to separate data struct
- Drop stale comment
intel:
- Update header block to reflect direct dependencies
- Extract intel_pinctrl_get_soc_data() helper for wider use
-----BEGIN PGP SIGNATURE-----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=H2KZ
-----END PGP SIGNATURE-----
Merge tag 'intel-pinctrl-v5.10-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pinctrl/intel into devel
intel-pinctrl for v5.10-1
* Add last part of cleanup Cherryview driver to align with other drivers
* Due to above clean up Cherryview and Baytrail drivers to use common API
The following is an automated git shortlog grouped by driver:
baytrail:
- Switch to use intel_pinctrl_get_soc_data()
cherryview:
- Preserve CHV_PADCTRL1_INVRXTX_TXDATA flag on GPIOs
- Switch to use intel_pinctrl_get_soc_data()
- Utilize temporary variable to hold device pointer
- Switch to use struct intel_pinctrl
- Move custom community members to separate data struct
- Drop stale comment
intel:
- Update header block to reflect direct dependencies
- Extract intel_pinctrl_get_soc_data() helper for wider use
- Add CAN and USB1 PWEN pin groups on R-Car H2 and RZ/G1,
- Three more conversion of DT bindings to json-schema,
- Group all Renesas pinctrl drivers and improve visual Kconfig
structure,
- Rename drivers/pinctrl/sh-pfc to drivers/pinctrl/renesas,
- Minor fixes and improvements.
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQ9qaHoIs/1I4cXmEiKwlD9ZEnxcAUCX2SoaQAKCRCKwlD9ZEnx
cKV6AP48BYvs8Fu3dd08ZRI3w82K56GQEi+9pJh+krkyQc8ODQD+JKbR48O15cN5
cQ0sJuVyAVRhEf9N7OerkbbBUCM+pQ8=
=jKcz
-----END PGP SIGNATURE-----
Merge tag 'renesas-pinctrl-for-v5.10-tag1' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into devel
pinctrl: renesas: Updates for v5.10
- Add CAN and USB1 PWEN pin groups on R-Car H2 and RZ/G1,
- Three more conversion of DT bindings to json-schema,
- Group all Renesas pinctrl drivers and improve visual Kconfig
structure,
- Rename drivers/pinctrl/sh-pfc to drivers/pinctrl/renesas,
- Minor fixes and improvements.
One some devices the GPIO should output the inverted value from what
device-drivers / ACPI code expects. The reason for this is unknown,
perhaps these systems use an external buffer chip on the GPIO which
inverts the signal. The BIOS makes this work by setting the
CHV_PADCTRL1_INVRXTX_TXDATA flag.
Before this commit we would unconditionally clear all INVRXTX flags,
including the CHV_PADCTRL1_INVRXTX_TXDATA flag when a GPIO is requested
by a driver (from chv_gpio_request_enable()).
This breaks systems using this setup. Specifically it is causing
problems for systems with a goodix touchscreen, where the BIOS sets the
INVRXTX_TXDATA flag on the GPIO used for the touchscreen's reset pin.
The goodix touchscreen driver by defaults configures this pin as input
(relying on the pull-up to keep it high), but the clearing of the
INVRXTX_TXDATA flag done by chv_gpio_request_enable() causes it to be
driven low for a brief time before the GPIO gets set to input mode.
This causes the touchscreen controller to get reset. On most CHT devs
with this touchscreen this leads to:
[ 31.596534] Goodix-TS i2c-GDIX1001:00: i2c test failed attempt 1: -121
The driver retries this though and then everything is fine. But during
reset the touchscreen uses its interrupt pin as bootstrap to determine
which i2c address to use and on the Acer One S1003 the spurious reset
caused by the clearing of the INVRXTX_TXDATA flag causes the controller
to come back up again on the wrong i2c address, breaking things.
This commit fixes both the -121 errors, as well as the total breakage
on the Acer One S1003, by making chv_gpio_clear_triggering() not clear
the INVRXTX_TXDATA flag if the pin is already configured as a GPIO.
Note that chv_pinmux_set_mux() does still unconditionally clear the
flag, so this only affects GPIO usage.
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Most, but not all, Renesas pin control drivers use the "sh-pfc" pin
control framework. As of commit 8449bfa9e6a9f7ec ("pinctrl: sh-pfc:
Collect Renesas related CONFIGs in one place"), the code for this
framework is always built when Renesas SoC pin control support is
enabled, regardless of whether the enabled pin control drivers need it
or not.
Fix this by reintroducing the CONFIG_SH_PFC symbol to control inclusion
of the "sh-pfc" framework and its dependencies, and selecting it when
needed.
This reduces kernel size of a typical RZ/A1 or RZ/A2 kernel by more than
6 resp. 11 KiB.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200909131534.12897-4-geert+renesas@glider.be
The drivers/pinctrl/sh-pfc subdirectory was originally created to group
pin control drivers for various Renesas SuperH and SH-Mobile platforms.
However, the name "sh-pfc" no longer reflects its contents, as the
directory now contains pin control drivers for Renesas SuperH, ARM32,
and ARM64 SoCs.
Hence rename the subdirectory from drivers/pinctrl/sh-pfc to
drivers/pinctrl/renesas, and the related Kconfig symbol from
PINCTRL_SH_PFC to PINCTRL_RENESAS.
Rename the git branch in MAINTAINERS, too, for consistency.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200909131534.12897-3-geert+renesas@glider.be
The RZ/N1 pin control driver does not use pin groups or pin functions,
so there is no need to select GENERIC_PINCTRL_GROUPS or
GENERIC_PINMUX_FUNCTIONS.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20200909131534.12897-2-geert+renesas@glider.be
For pins requiring software driven IO output operations, the RZ/A1 Pin
Controller uses either the "output-high" or "output-low" DT property to
enable the corresponding output buffer. The actual line value doesn't
matter, as it is ignored.
Commit 425562429d ("pinctrl: generic: Add output-enable property")
introduced a new DT property for this specific use case.
Update the RZ/A1 Pin Controller DT bindings and driver to use this new
property instead. Preserve backwards compatibility with old DTBs in the
driver, as this comes at a very small cost.
Notes:
- The DT binding examples already used the new property,
- There are no upstream users of the old properties.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Chris Brandt <chris.brandt@renesas.com>
Acked-by: Jacopo Mondi <jacopo@jmondi.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200821111401.4021-1-geert+renesas@glider.be
Now, Renesas Pin Control drivers are under menu, but current
descriptions are not aligned.
This patch aligns them.
- RZ/A2 gpio and pinctrl driver
- RZ/N1 pinctrl driver
- Emma Mobile EV2 pin control support
- R-Mobile APE6 pin control support
- R-Mobile A1 pin control support
- RZ/G1H pin control support
- RZ/G1M pin control support
+ pin control support for RZ/A2
+ pin control support for RZ/N1
+ pin control support for Emma Mobile EV2
+ pin control support for R-Mobile APE6
+ pin control support for R-Mobile A1
+ pin control support for RZ/G1H
+ pin control support for RZ/G1M
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87imd8y4r2.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Renesas related pinctrl CONFIGs are located in many places, which is
confusing.
This patch collects them into the same place, grouped in a new "Renesas
pinctrl drivers" menu.
This patch also moves pinctrl-rz{a1,a2,n1}.c into the sh-pfc folder.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87k0xoy4r7.wl-kuninori.morimoto.gx@renesas.com
[geert: Update path in MAINTAINERS]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
It is "Emma Mobile EV2" not "AV2".
This patch tidies it up.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87lfi4y4re.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
driver_deferred_probe_check_state() may return -ETIMEDOUT instead of
-EPROBE_DEFER after all built-in drivers have been probed. This can
cause issues for built-in drivers that depend on resources provided by
loadable modules.
One such case happens on Tegra where I2C controllers are used during
early boot to set up the system PMIC, so the I2C driver needs to be a
built-in driver. At the same time, some instances of the I2C controller
depend on the DPAUX hardware for pinmuxing. Since the DPAUX is handled
by the display driver, which is usually not built-in, the pin control
states will not become available until after the root filesystem has
been mounted and the display driver loaded from it.
Fixes: bec6c0ecb2 ("pinctrl: Remove use of driver_deferred_probe_check_state_continue()")
Suggested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Link: https://lore.kernel.org/r/20200825143348.1358679-1-thierry.reding@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Per the datasheet the i2c functions use MPP_Sel=0x1. They are documented
as using MPP_Sel=0x4 as well but mixing 0x1 and 0x4 is clearly wrong. On
the board tested 0x4 resulted in a non-functioning i2c bus so stick with
0x1 which works.
Fixes: d7ae8f8dee ("pinctrl: mvebu: pinctrl driver for 98DX3236 SoC")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20200907211712.9697-2-chris.packham@alliedtelesis.co.nz
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
I encountered bug in SX1502 expander driver in 5.7.7. Here is relevant
DTS part:
compatible = "semtech,sx1502q";
gpio4_cfg_pins: gpio2-cfg {
pins = "gpio5";
output-high;
};
And part of OOPS:
[ 0.673996] [<c023cfa6>] (gpiochip_get_data) from [<c023b235>]
(sx150x_gpio_direction_output+0xd)
[ 0.683259] [<c023b235>] (sx150x_gpio_direction_output) from
[<c023b363>] (sx150x_pinconf_set+0x)
[ 0.692796] [<c023b363>] (sx150x_pinconf_set) from [<c0238fef>]
(pinconf_apply_setting+0x39/0x7e)
[ 0.701635] [<c0238fef>] (pinconf_apply_setting) from [<c0236c77>]
(pinctrl_commit_state+0xa5/0x)
[ 0.710648] [<c0236c77>] (pinctrl_commit_state) from [<c0237e03>]
(pinctrl_enable+0xff/0x1d4)
[ 0.719139] [<c0237e03>] (pinctrl_enable) from [<c023b791>]
(sx150x_probe+0x1a3/0x358)
[ 0.727027] [<c023b791>] (sx150x_probe) from [<c02c38bf>]
(i2c_device_probe+0x1bb/0x1dc)
The problem is that sx150x_pinconf_set uses sx150x_gpio_direction_output
but gpio is not setup yet. Patch below fixes it but I'm not sure whether
is it correct.
Link: https://lore.kernel.org/r/f32130bf-cfd4-b1bf-538c-dbc9ee2d947a@eaxlabs.cz
Signed-off-by: Martin DEVERA <devik@eaxlabs.cz>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Rockchip pinctrl driver needs to handle information from Devicetree
so only makes sense getting compiled on systems with CONFIG_OF enabled.
This also fixes a problem found by the "kernel-test-robot" when compiling
the driver on test-builds that do not have CONFIG_OF enabled:
drivers/pinctrl/pinctrl-rockchip.c: In function 'rockchip_pinctrl_parse_groups':
>> drivers/pinctrl/pinctrl-rockchip.c:2881:9: error: implicit declaration of function 'pinconf_generic_parse_dt_config'; did you mean 'pinconf_generic_dump_config'? [-Werror=implicit-function-declaration]
2881 | ret = pinconf_generic_parse_dt_config(np_config, NULL,
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
| pinconf_generic_dump_config
drivers/pinctrl/pinctrl-rockchip.c: In function 'rockchip_gpiolib_register':
>> drivers/pinctrl/pinctrl-rockchip.c:3473:5: error: 'struct gpio_chip' has no member named 'of_node'
3473 | gc->of_node = bank->of_node;
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
Link: https://lore.kernel.org/r/20200905214955.907950-1-heiko@sntech.de
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of s900_padinfo[] is to assign it to the padinfo field in
the owl_pinctrl_soc_data struct, which is a const pointer. Make it const
to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200830224311.36994-4-rikard.falkeborn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of s700_padinfo[] is to assign it to the padinfo field in
the owl_pinctrl_soc_data struct, which is a const pointer. Make it const
to allow the compiler to put it in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200830224311.36994-3-rikard.falkeborn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The only usage of owl_pinctrl_ops and owl_pinmux_ops is to assign their
addresses to the pctlops and the pmxops fields in the pinctrl_desc struct,
which are const pointers. Make them const to allow the compiler to put them
in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20200830224311.36994-2-rikard.falkeborn@gmail.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
On page 23 of the datasheet [0] it says "The register remains unchanged
until the interrupt is cleared via a read of INTCAP or GPIO." Include
INTCAPA and INTCAPB registers in precious range, so that they aren't
accidentally cleared when we read via debugfs.
[0] https://ww1.microchip.com/downloads/en/DeviceDoc/20001952C.pdf
Fixes: 8f38910ba4 ("pinctrl: mcp23s08: switch to regmap caching")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828213226.1734264-3-thomas.preston@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The mcp23x17_regmap is initialised with structs named "mcp23x16".
However, the mcp23s08 driver doesn't support the MCP23016 device yet, so
this appears to be a typo.
Fixes: 8f38910ba4 ("pinctrl: mcp23s08: switch to regmap caching")
Signed-off-by: Thomas Preston <thomas.preston@codethink.co.uk>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Link: https://lore.kernel.org/r/20200828213226.1734264-2-thomas.preston@codethink.co.uk
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
One some devices the GPIO should output the inverted value from what
device-drivers / ACPI code expects. The reason for this is unknown,
perhaps these systems use an external buffer chip on the GPIO which
inverts the signal. The BIOS makes this work by setting the
CHV_PADCTRL1_INVRXTX_TXDATA flag.
Before this commit we would unconditionally clear all INVRXTX flags,
including the CHV_PADCTRL1_INVRXTX_TXDATA flag when a GPIO is requested
by a driver (from chv_gpio_request_enable()).
This breaks systems using this setup. Specifically it is causing
problems for systems with a goodix touchscreen, where the BIOS sets the
INVRXTX_TXDATA flag on the GPIO used for the touchscreen's reset pin.
The goodix touchscreen driver by defaults configures this pin as input
(relying on the pull-up to keep it high), but the clearing of the
INVRXTX_TXDATA flag done by chv_gpio_request_enable() causes it to be
driven low for a brief time before the GPIO gets set to input mode.
This causes the touchscreen controller to get reset. On most CHT devs
with this touchscreen this leads to:
[ 31.596534] Goodix-TS i2c-GDIX1001:00: i2c test failed attempt 1: -121
The driver retries this though and then everything is fine. But during
reset the touchscreen uses its interrupt pin as bootstrap to determine
which i2c address to use and on the Acer One S1003 the spurious reset
caused by the clearing of the INVRXTX_TXDATA flag causes the controller
to come back up again on the wrong i2c address, breaking things.
This commit fixes both the -121 errors, as well as the total breakage
on the Acer One S1003, by making chv_gpio_clear_triggering() not clear
the INVRXTX_TXDATA flag if the pin is already configured as a GPIO.
Note that chv_pinmux_set_mux() does still unconditionally clear the
flag, so this only affects GPIO usage.
Fixes: a7d4b17166 ("Input: goodix - add support for getting IRQ + reset GPIOs on Cherry Trail devices")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Print particular message in each of error case in the ->probe().
While here, use dev_err_probe() for that.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200828103235.78380-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Add initial Qualcomm msm8226 pinctrl driver to support pin configuration
with pinctrl framework for msm8226 SoC.
- Initial formatting and style was taken from the msm8x74 pinctrl driver
added by Björn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Bartosz Dudziak <bartosz.dudziak@snejp.pl>
Link: https://lore.kernel.org/r/20200716205530.22910-3-bartosz.dudziak@snejp.pl
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Group name 'pcie1' is misleading as it controls only PCIe reset pin. Like
other PCIe groups it should have been called 'pcie1_reset'. But due to
backward compatibility it is not possible to change existing group name.
So just add comment describing this PCIe reset functionality.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20200724132457.7094-1-pali@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The nomadik pinctrl hardware doesn't have any way to
determine if the active pull is up or down. Reading
the bit currently used to report if the pull is up/down
indicates if the gpio input is reading high or low, it
doesn't reflect the pull state.
For this reason change the output from "pull up"/"pull down" to
"pull enabled". This avoids confusing developers who were using
the output to determine what the pull state is.
Signed-off-by: Andrew Halaney <ajhalaney@gmail.com>
Link: https://lore.kernel.org/r/20200806155322.GA25523@ola-jn9phv2.ad.garmin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Update header inclusion block to reflect all direct dependencies
that are being involved in pinctrl-intel.h.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we have common helper to retrieve SoC data from driver data
we may switch to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Since we have common helper to retrieve SoC data from driver data
we may switch to use it.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
intel_pinctrl_get_soc_data() helper can be used in few driver instead of
open-coded variants. Thus, extract it as a standalone API.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
By one of the previous clean up change we got a temporary variable to hold
a device pointer. It can be utilized in other calls in the ->probe() and
save a bit of LOCs.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Now when all preparations are done we may easily switch to use
struct intel_pinctrl instead of custom one.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
This is a preparatory patch for bigger clean up pending for Cherryview driver.
There is no functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
There is no more .groups member in struct chv_pinctrl,
drop associated comment because it's not applicable anymore.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
kernel series:
Core changes:
- The GPIO patch "gpiolib: Introduce
for_each_requested_gpio_in_range() macro" was put in an
immutable branch and merged into the pinctrl tree as well.
We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among
other things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have
been modularized. This is driven by the Google Android
GKI initiative I think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
-----BEGIN PGP SIGNATURE-----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=mJgb
-----END PGP SIGNATURE-----
Merge tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of the pin control changes for the v5.9 kernel
series:
Core changes:
- The GPIO patch "gpiolib: Introduce for_each_requested_gpio_in_range()
macro" was put in an immutable branch and merged into the pinctrl
tree as well. We see these changes also here.
- Improved debug output for pins used as GPIO.
New drivers:
- Ocelot Sparx5 SoC driver.
- Intel Emmitsburg SoC subdriver.
- Intel Tiger Lake-H SoC subdriver.
- Qualcomm PM660 SoC subdriver.
- Renesas SH-PFC R8A774E1 subdriver.
Driver improvements:
- Linear improvement and cleanups of the Intel drivers for
Cherryview, Lynxpoint, Baytrail etc. Improved locking among other
things.
- Renesas SH-PFC has added support for RPC pins, groups, and
functions to r8a77970 and r8a77980.
- The newere Freescale (now NXP) i.MX8 pin controllers have been
modularized. This is driven by the Google Android GKI initiative I
think.
- Open drain support for pins on the Qualcomm IPQ4019.
- The Ingenic driver can handle both edges IRQ detection.
- A big slew of documentation fixes all over the place.
- A few irqchip template conversions by yours truly.
* tag 'pinctrl-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (107 commits)
dt-bindings: pinctrl: add bindings for MediaTek MT6779 SoC
pinctrl: stmfx: Use irqchip template
pinctrl: amd: Use irqchip template
pinctrl: mediatek: fix build for tristate changes
pinctrl: samsung: Use bank name as irqchip name
pinctrl: core: print gpio in pins debugfs file
pinctrl: mediatek: add mt6779 eint support
pinctrl: mediatek: add pinctrl support for MT6779 SoC
pinctrl: mediatek: avoid virtual gpio trying to set reg
pinctrl: mediatek: update pinmux definitions for mt6779
pinctrl: stm32: use the hwspin_lock_timeout_in_atomic() API
pinctrl: mcp23s08: Use irqchip template
pinctrl: sx150x: Use irqchip template
dt-bindings: ingenic,pinctrl: Support pinmux/pinconf nodes
pinctrl: intel: Add Intel Emmitsburg pin controller support
pinctl: ti: iodelay: Replace HTTP links with HTTPS ones
Revert "gpio: omap: handle pin config bias flags"
pinctrl: single: Use fallthrough pseudo-keyword
pinctrl: qcom: spmi-gpio: Use fallthrough pseudo-keyword
pinctrl: baytrail: Use fallthrough pseudo-keyword
...
Core changes:
- Introduce the for_each_requested_gpio() macro to help in
dependent code all over the place. Also patch a few locations
to use it while we are at it.
- Split out the sysfs code into its own file.
- Split out the character device code into its own file, then
make a set of refactorings and improvements to this code.
We are setting the stage to revamp the userspace API a bit
in the next cycle.
- Fix a whole slew of kerneldoc that was wrong or missing.
New drivers:
- The PCA953x driver now supports the PCAL9535.
Driver improvements:
- A host of incremental modernizations and improvements to the
PCA953x driver.
- Incremental improvements to the Xilinx Zynq driver.
- Some improvements to the GPIO aggregator driver.
- I ran all over the place switching all threaded and other
drivers requesting their own IRQ while using the core
GPIO IRQ helpers to pass the GPIO irq chip as a template
instead of calling the explicit set-up functions. Next merge
window we may retire the old code altogether.
-----BEGIN PGP SIGNATURE-----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=OSvz
-----END PGP SIGNATURE-----
Merge tag 'gpio-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.9 kernel cycle.
There is nothing too exciting in it, but a new macro that fixes a
build failure on a minor ARM32 platform that appeared yesterday is
part of it so we better merge it.
Core changes:
- Introduce the for_each_requested_gpio() macro to help in dependent
code all over the place. Also patch a few locations to use it while
we are at it.
- Split out the sysfs code into its own file.
- Split out the character device code into its own file, then make a
set of refactorings and improvements to this code. We are setting
the stage to revamp the userspace API a bit in the next cycle.
- Fix a whole slew of kerneldoc that was wrong or missing.
New drivers:
- The PCA953x driver now supports the PCAL9535.
Driver improvements:
- A host of incremental modernizations and improvements to the
PCA953x driver.
- Incremental improvements to the Xilinx Zynq driver.
- Some improvements to the GPIO aggregator driver.
- I ran all over the place switching all threaded and other drivers
requesting their own IRQ while using the core GPIO IRQ helpers to
pass the GPIO irq chip as a template instead of calling the
explicit set-up functions. Next merge window we may retire the old
code altogether"
* tag 'gpio-v5.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (97 commits)
gpio: wcove: Request IRQ after all initialisation done
gpio: crystalcove: Free IRQ on error path
gpio: pca953x: Request IRQ after all initialisation done
gpio: don't use same lockdep class for all devm_gpiochip_add_data users
gpio: max732x: Use irqchip template
gpio: stmpe: Move chip registration
gpio: rcar: Use irqchip template
gpio: regmap: fix type clash
gpio: Correct kernel-doc inconsistency
gpio: pci-idio-16: Use irqchip template
gpio: pcie-idio-24: Use irqchip template
gpio: 104-idio-16: Use irqchip template
gpio: 104-idi-48: Use irqchip template
gpio: 104-dio-48e: Use irqchip template
gpio: ws16c48: Use irqchip template
gpio: omap: improve coding style for pin config flags
gpio: dln2: Use irqchip template
gpio: sch: Add a blank line between declaration and code
gpio: sch: changed every 'unsigned' to 'unsigned int'
gpio: ich: changed every 'unsigned' to 'unsigned int'
...
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit calls to gpiochip_irqchip_add_nested() and
gpiochip_set_nested_irqchip(). The irqchip is instead
added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Amelie Delaunay <amelie.delaunay@st.com>
Cc: Benjamin Gaignard <benjamin.gaignard@st.com>
Link: https://lore.kernel.org/r/20200721131814.357182-1-linus.walleij@linaro.org
This makes the driver use the irqchip template to assign
properties to the gpio_irq_chip instead of using the
explicit call to gpiochip_irqchip_add().
The irqchip is instead added while adding the gpiochip.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Shyam Sundar S K <Shyam-sundar.S-k@amd.com>
Cc: Sandeep Singh <sandeep.singh@amd.com>
Link: https://lore.kernel.org/r/20200722101545.144373-1-linus.walleij@linaro.org
Export mtk_is_virt_gpio() for the case when
CONFIG_PINCTRL_MTK=y
CONFIG_PINCTRL_MTK_V2=y
CONFIG_PINCTRL_MTK_MOORE=y
CONFIG_PINCTRL_MTK_PARIS=m
to fix this build error:
ERROR: modpost: "mtk_is_virt_gpio" [drivers/pinctrl/mediatek/pinctrl-paris.ko] undefined!
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Sean Wang <sean.wang@kernel.org>
Cc: linux-mediatek@lists.infradead.org
Link: https://lore.kernel.org/r/d15827a3-d0c8-e231-9f61-8507b3d7be3a@infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use the bank name as the irqchip name. This name is later visible in
/proc/interrupts, what makes it possible to easily identify each
GPIO interrupt.
/proc/interrupts before this patch:
143: 0 exynos4210_wkup_irq_chip 7 Edge hdmi
144: 0 exynos4210_wkup_irq_chip 6 Level wm8994
145: 1 exynos4210_wkup_irq_chip 7 Edge max77686-pmic, max77686-rtc
146: 1 exynos_gpio_irq_chip 3 Edge 3-0048
/proc/interrupts after this patch:
143: 0 gpx3 7 Edge hdmi
144: 0 gpx3 6 Level wm8994
145: 1 gpx0 7 Edge max77686-pmic, max77686-rtc
146: 1 gpm2 3 Edge 3-0048
Handling of the eint_wake_mask_value has been reworked, because each bank
has now its own exynos_irq_chip structure allocated.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20200720145412.24221-1-krzk@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
add driver setting to support mt6779 eint
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Hanks Chen <hanks.chen@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/1595503197-15246-6-git-send-email-hanks.chen@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This adds MT6779 pinctrl driver based on MediaTek pinctrl-paris core.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Andy Teng <andy.teng@mediatek.com>
Signed-off-by: Hanks Chen <hanks.chen@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/1595503197-15246-5-git-send-email-hanks.chen@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
for virtual gpios, they should not do reg setting and
should behave as expected for eint function.
Signed-off-by: Mars Cheng <mars.cheng@mediatek.com>
Signed-off-by: Hanks Chen <hanks.chen@mediatek.com>
Acked-by: Sean Wang <sean.wang@kernel.org>
Link: https://lore.kernel.org/r/1595503197-15246-4-git-send-email-hanks.chen@mediatek.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Hsin-Yi Wang