For max bundle size 32, the bundle mask is not same with 8/16.
Change it to match the max bundle size of htc. Otherwise it
will not match with firmware, for example, when bundle count
is 17, then flags of ath10k_htc_hdr is 0x4, if without this
patch, it will be considered as non-bundled packet because it
does not have mask 0xF0, then trigger error message later:
payload length 56747 exceeds max htc length: 4088.
htc->max_msgs_per_htc_bundle is the min value of
HTC_HOST_MAX_MSG_PER_RX_BUNDLE and
msg->ready_ext.max_msgs_per_htc_bundle of ath10k_htc_wait_target,
it will be sent to firmware later in ath10k_htc_start, then
firmware will use it as the final max rx bundle count, in
WLAN.RMH.4.4.1-00029, msg->ready_ext.max_msgs_per_htc_bundle
is 32, it is same with HTC_HOST_MAX_MSG_PER_RX_BUNDLE, so the
final max rx bundle count will be set to 32 in firmware.
This patch only effect sdio chips.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Fixes: 224776520e ("ath10k: change max RX bundle size from 8 to 32 for sdio")
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For tcp RX, the quantity of tcp acks to remote is 1/2 of the quantity
of tcp data from remote, then it will have many small length packets
on TX path of sdio bus, then it reduce the RX packets's bandwidth of
tcp.
This patch enable napi on RX path, then the RX packet of tcp will not
feed to tcp stack immeditely from mac80211 since GRO is enabled by
default, it will feed to tcp stack after napi complete, if rx bundle
is enabled, then it will feed to tcp stack one time for each bundle
of RX. For example, RX bundle size is 32, then tcp stack will receive
one large length packet, its length is neary 1500*32, then tcp stack
will send a tcp ack for this large packet, this will reduce the tcp
acks ratio from 1/2 to 1/32. This results in significant performance
improvement for tcp RX.
Tcp rx throughout is 240Mbps without this patch, and it arrive 390Mbps
with this patch. The cpu usage has no obvious difference with and
without NAPI.
call stack for each RX packet on GRO path:
(skb length is about 1500 bytes)
skb_gro_receive ([kernel.kallsyms])
tcp4_gro_receive ([kernel.kallsyms])
inet_gro_receive ([kernel.kallsyms])
dev_gro_receive ([kernel.kallsyms])
napi_gro_receive ([kernel.kallsyms])
ieee80211_deliver_skb ([mac80211])
ieee80211_rx_handlers ([mac80211])
ieee80211_prepare_and_rx_handle ([mac80211])
ieee80211_rx_napi ([mac80211])
ath10k_htt_rx_proc_rx_ind_hl ([ath10k_core])
ath10k_htt_rx_pktlog_completion_handler ([ath10k_core])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
call stack for napi complete and send tcp ack from tcp stack:
(skb length is about 1500*32 bytes)
_tcp_ack_snd_check ([kernel.kallsyms])
tcp_v4_do_rcv ([kernel.kallsyms])
tcp_v4_rcv ([kernel.kallsyms])
local_deliver_finish ([kernel.kallsyms])
ip_local_deliver ([kernel.kallsyms])
ip_rcv_finish ([kernel.kallsyms])
ip_rcv ([kernel.kallsyms])
netif_receive_skb_core ([kernel.kallsyms])
netif_receive_skb_one_core([kernel.kallsyms])
netif_receive_skb ([kernel.kallsyms])
netif_receive_skb_internal ([kernel.kallsyms])
napi_gro_complete ([kernel.kallsyms])
napi_gro_flush ([kernel.kallsyms])
napi_complete_done ([kernel.kallsyms])
ath10k_sdio_napi_poll ([ath10k_sdio])
net_rx_action ([kernel.kallsyms])
__softirqentry_text_start ([kernel.kallsyms])
do_softirq ([kernel.kallsyms])
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio does not support wow, this patch is to enable it. When system enter
sleep state, if wowlan is enabled, then sdio chip will keep power if
platform support keep power, after resume, it will not need to re-load
firmware again.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Change log level from warn to dbg level of mpdu status
of sdio chip.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After the firmware crashes ath10k recovers via ieee80211_reconfig(),
which eventually leads to firmware configuration and including the
encryption keys. However, because there is no new auth/assoc and
4-way-handshake, and firmware set the authorize flag after
4-way-handshake, so the authorize flag in firmware is not set in
firmware without 4-way-handshake. This will lead to a failure of data
transmission after recovery done when using encrypted connections like
WPA-PSK. Set authorize flag after installing keys to firmware will fix
the issue.
This was noticed by testing firmware crashing using simulate_fw_crash
debugfs file.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For sdio chip, the max credit size in firmware is 1556, the 1556
include payload, ieee80211 header, htt header, htc header. So it
need to set the max mtu to 1500 to forbidden TX packet which exceed
1500 form application.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On SDIO chips the firmware log does not impact performance. To make it
easier to debug firmware problems keep it enabled on the firmware.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
During driver load below warn logs are printed in the console if
firmware doesn't support some optional HTC services, ex:pktlog.
It is likely some older fw version may not support PKTLOG HTC
service as legacy fw uses HTC DATA service for pktlog.
Move this log to debug level to remove un-necessary warn message
on console.
htc.c:803: ath10k_warn(ar, "unsupported HTC service id: %d\n",
htc.c:881: ath10k_warn(ar, "unsupported HTC service id: %d\n",
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Rework event_create_dir() to use an array of static data instead of
function pointers where possible.
The problem is that it would call the function pointer on module load
before parse_args(), possibly even before jump_labels were initialized.
Luckily the generated functions don't use jump_labels but it still seems
fragile. It also gets in the way of changing when we make the module map
executable.
The generated function are basically calling trace_define_field() with a
bunch of static arguments. So instead of a function, capture these
arguments in a static array, avoiding the function call.
Now there are a number of cases where the fields are dynamic (syscall
arguments, kprobes and uprobes), in which case a static array does not
work, for these we preserve the function call. Luckily all these cases
are not related to modules and so we can retain the function call for
them.
Also fix up all broken tracepoint definitions that now generate a
compile error.
Tested-by: Alexei Starovoitov <ast@kernel.org>
Tested-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Reviewed-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/20191111132458.342979914@infradead.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
So far, frames were forwarded regardless of the FCS correctness leading
to userspace applications listening on the monitor mode interface to
receive potentially broken frames, even with the "fcsfail" flag unset.
By default, with the "fcsfail" flag of a monitor mode interface
unset, frames with FCS errors should be dropped. With this patch, the
fcsfail flag is taken into account correctly.
Tested-on: QCA4019 firmware-5-ct-full-community-12.bin-lede.011
Cc: Simon Wunderlich <sw@simonwunderlich.de>
Signed-off-by: Linus Lüssing <ll@simonwunderlich.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
iw command only show rssi without each chain's rssi on sdio
iw wlan0 station dump
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 dBm
signal avg: -82 dBm
after this patch, it will show each chain's rssi on sdio
Station a0:40:a0:93:3e:de (on wlan0)
signal: -82 [-84, -88] dBm
signal avg: -82 [-84, -87] dBm
For QCA6174 PCIe, the ppdu have the correct rssi of each chain, it
indicate rssi of rx data by ath10k_htt_rx_h_signal. For sdio chip, the
rssi of each chain stored in rx management reported by firmware, the
ath10k_wmi_tlv_op_pull_mgmt_rx_ev which used for tlv wmi will get the
rssi of each chain and stored them in wmi_mgmt_rx_ev_arg, then indicate
them to mac80211. For non-tlv wmi chip, it will not get the rssi of each
chain and not indicate to mac80211, for non-tlv wmi chip, this patch will
not have impact. For tlv wmi chip, if the rssi of chain in mgmt is valid,
it will be indicate to mac80211, tested with QCA6174 PCIe/SDIO, the rssi
of 2 chain in mgmt is valid.
rssi of chains in mgmt of QCA6174 SDIO:
92096.652780: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[0]:70
92096.657324: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[1]:68
92096.662009: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[2]:128
92096.666647: ath10k:ath10k_log_warn: ath10k_sdio mmc1:0001:1 rssi[3]:128
rssi of chains in mgmt of QCA6174 PCIe:
[ 1581.049816] ath10k_pci 0000:02:00.0: mgmt rssi[0]:17
[ 1581.049818] ath10k_pci 0000:02:00.0: mgmt rssi[1]:22
[ 1581.049821] ath10k_pci 0000:02:00.0: mgmt rssi[2]:128
[ 1581.049823] ath10k_pci 0000:02:00.0: mgmt rssi[3]:128
after apply this patch, the iw's rssi of PCIe do not changed, result is
same with before.
iw wlan0 station dump of QCA6174 PCIe:
Station 6c:e8:73:b8:92:dc (on wlan0)
signal: -70 [-77, -72] dBm
signal avg: -69 [-78, -72] dBm
iw wlan-5000mhz station dump of QCA9984 PCIe
connected with 2 client which has 2 chain:
Station 70:48:0f:1f:1a:b2 (on wlan-5000mhz)
signal: -47 [-55, -48, -87, -88] dBm
signal avg: -42 [-50, -43, -83, -86] dBm
Station ac:c1:ee:39:e3:83 (on wlan-5000mhz)
signal: -43 [-46, -45, -79, -84] dBm
signal avg: -43 [-46, -46, -82, -83] dBm
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Tested with QCA6174 PCIe with firmware WLAN.RM.4.4.1-00110-QCARMSWP-1.
Tested with QCA9984 PCIe with firmware 10.4-3.9.0.2-00040.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the BDF download QMI message has the end field set to 1, it signals
the end of the transfer, and triggers the firmware to do a CRC check. The
BDFs for msm8998 devices fail this check, yet the firmware is happy to
still use the BDF. It appears that this error is not caught by the
downstream drive by concidence, therefore there are production devices
in the field where this issue needs to be handled otherwise we cannot
support wifi on them. So, attempt to detect this scenario as best we can
and treat it as non-fatal.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When ath10k_qmi_init() fails, the error handling does not free the irq
resources, which causes an issue if we EPROBE_DEFER as we'll attempt to
(re-)register irqs which are already registered.
Fix this by doing a power off since we just powered on the hardware, and
freeing the irqs as error handling.
Fixes: ba94c753cc ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add NL80211_FEATURE_ND_RANDOM_MAC_ADDR for NLO will enable the random
mac address for netdetect case.
iw command:
iw phy0 wowlan enable net-detect net-detect
randomize=AA:7B:A1:AC:B2:41/FF:FF:FF:FF:FF:FF interval 5000 delay 30
freqs 2412 matches ssid foo.
After suspend, DUT will send probe request with mac AA:7B:A1:AC:B2:41.
WCN3990, QCA9377, QCA6174 PCI also support this feature.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00029.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware with the build id QC_IMAGE_VERSION_STRING=WLAN.HL.1.0.2-XXXX does
not support the QMI_WLFW_HOST_CAP_REQ_V01 message and will return the
QMI not supported error to the ath10k driver. Since not supporting this
message is not fatal to the firmware nor the ath10k driver, lets catch
this particular scenario and ignore it so that we can still bring up
wifi services successfully.
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Download firmware time cost of SDIO is too long, it is about 480ms,
add large size 2048 bytes for BMI download for SDIO chip, its time
cost will reduced to 240ms.
This will optimize the download firmware time cost.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
the tlv len is set to the total len of the wmi cmd, it will trigger
firmware crash, correct the tlv len.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1 and QCA6174
PCIE with firmware WLAN.RM.4.4.1-00110-QCARMSWPZ-1.
Fixes: ce834e280f ("ath10k: support NET_DETECT WoWLAN feature")
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For RX, it has two parts, one is to read data from sdio, another
is to indicate the packets to upper stack. Recently it has only
one thread to do all RX things, it results that it is sequential
for RX and low throughout, change RX to parallel for the two parts
will increase throughout.
This patch move the indication to a workqueue, it results in
significant performance improvement on RX path.
Udp rx throughout is 200Mbps without this patch, and it arrives
400Mbps with this patch.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The max bundle size support by firmware is 32, change it from 8 to 32
will help performance. This results in significant performance
improvement on RX path.
The real max rx bundle is decided in ath10k_htc_wait_target(),
it is the min value of HTC_HOST_MAX_MSG_PER_RX_BUNDLE and the value reported
from firmware. So this change shouldn't cause any regressions with other
hardware supported by ath10k.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWPZ-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The existing implementation of initiating multiple sdio transfers for
receive bundling is slowing down the receive speed. Combining the
transfers using a bundle method would be ideal.
The transmission utilization ratio for sdio bus for small packet is
slow, because the space and time cost for sdio bus is same for large
length packet and small length packet. So the speed of data for large
length packet is higher than small length.
Test result of different length of data:
data packet(byte) cost time(us) calculated rate(Mbps)
256 28 73
512 33 124
1024 35 234
1792 45 318
14336 168 682
28672 333 688
57344 660 695
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWPZ-1
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Unless we sleep for a while before transitioning the MSA memory to WLAN
the MPSS.AT.4.0.c2-01184-SDM845_GEN_PACK-1 firmware triggers a security
violation fairly reliably. Unforutnately recovering from this failure
always results in the entire system freezing.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This reverts commit 334f5b61a6.
This caused ath10k_snoc on Qualcomm MSM8998, SDM845 and QCS404 platforms to
trigger an assert in the firmware:
err_qdi.c:456:EF:wlan_process:1:cmnos_thread.c:3900:Asserted in wlan_vdev.c:_wlan_vdev_up:3219
Revert the offending commit for now.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Downloading ath10k firmware needs a large number of IOs and
cpuidle's miss predictions make it worse. In the worst case,
resume time can be three times longer than the average on sdio.
This patch disables cpuidle during firmware downloading by
applying PM_QOS_CPU_DMA_LATENCY in ath10k_download_fw().
Tested-on: QCA9880
Tested-on: QCA6174 hw3.2 SDIO WLAN.RMH.4.4.1-00029
Signed-off-by: Ikjoon Jang <ikjn@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
STA number was not restored if OOM happened.
Tested: QCA9984 with firmware ver 10.4-3.9.0.1-00018
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k does not provide transmit rate info per MSDU
in tx completion, mark that as -1 so mac80211
will ignore the rates. This fixes mac80211 update Mesh
link metric with invalid transmit rate info.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Hou Bao Hou <houbao@codeaurora.org>
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The `ar_usb` field of `ath10k_usb_pipe_usb_pipe` objects
are initialized to point to the containing `ath10k_usb` object
according to endpoint descriptors read from the device side, as shown
below in `ath10k_usb_setup_pipe_resources`:
for (i = 0; i < iface_desc->desc.bNumEndpoints; ++i) {
endpoint = &iface_desc->endpoint[i].desc;
// get the address from endpoint descriptor
pipe_num = ath10k_usb_get_logical_pipe_num(ar_usb,
endpoint->bEndpointAddress,
&urbcount);
......
// select the pipe object
pipe = &ar_usb->pipes[pipe_num];
// initialize the ar_usb field
pipe->ar_usb = ar_usb;
}
The driver assumes that the addresses reported in endpoint
descriptors from device side to be complete. If a device is
malicious and does not report complete addresses, it may trigger
NULL-ptr-deref `ath10k_usb_alloc_urb_from_pipe` and
`ath10k_usb_free_urb_to_pipe`.
This patch fixes the bug by preventing potential NULL-ptr-deref.
Signed-off-by: Hui Peng <benquike@gmail.com>
Reported-by: Hui Peng <benquike@gmail.com>
Reported-by: Mathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
[groeck: Add driver tag to subject, fix build warning]
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The dev_kfree_skb() function performs also input parameter validation.
Thus the test around the shown calls is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In commit 518a2f1925
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The return value of dma_map_single() should be checked for errors using
dma_mapping_error() and the skb has been dequeued so it needs to be
freed.
This was found when enabling CONFIG_DMA_API_DEBUG and it warned about the
missing dma_mapping_error() call.
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Reported-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The memory of ar->debug.tpc_stats_final is reallocated every debugfs
reading, it should be freed in ath10k_debug_destroy() for the last
allocation.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If firmware reports rate_max > WMI_TPC_RATE_MAX(WMI_TPC_FINAL_RATE_MAX)
or num_tx_chain > WMI_TPC_TX_N_CHAIN, it will cause array out-of-bounds
access, so print a warning and reset to avoid memory corruption.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently when pointer crash_data is null the present null check
will also check that crash_data->ramdump_buf is null and will cause
a null pointer dereference on crash_data. Fix this by using the ||
operator instead of &&.
Fixes: 3f14b73c38 ("ath10k: Enable MSA region dump support for WCN3990")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For all data packets transmitted, host gets htt tx completion event. Some QCA9984
firmware releases support WMI_SERVICE_TX_DATA_ACK_RSSI, which gives data
ack rssi values to host through htt event of data tx completion. Data ack rssi
values are valid if A0 bit is set in HTT rx message. So enable the feature also
for QCA9884.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00044
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
[kvalo@codeaurora.org: improve commit log]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When hardware rfkill is enabled in the firmware it will report the
capability via using WMI_TLV_SYS_CAP_INFO_RFKILL bit in the WMI_SERVICE_READY
event to the host. ath10k will check the capability, and if it is enabled then
ath10k will set the GPIO information to firmware using WMI_PDEV_SET_PARAM. When
the firmware detects hardware rfkill is enabled by the user, it will report it
via WMI_RFKILL_STATE_CHANGE_EVENTID. Once ath10k receives the event it will
send wmi command WMI_PDEV_SET_PARAM to the firmware to enable/disable the radio
and also notifies cfg80211.
We can't power off the device when rfkill is enabled, as otherwise the
firmware would not be able to detect GPIO changes and report them to the
host. So when rfkill is enabled, we need to keep the firmware running.
Tested with QCA6174 PCI with firmware
WLAN.RM.4.4.1-00109-QCARMSWPZ-1.
Signed-off-by: Alan Liu <alanliu@codeaurora.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch restores the old behavior that read
the chip_id on the QCA988x before resetting the
chip. This needs to be done in this order since
the unsupported QCA988x AR1A chips fall off the
bus when resetted. Otherwise the next MMIO Op
after the reset causes a BUS ERROR and panic.
Cc: stable@vger.kernel.org
Fixes: 1a7fecb766 ("ath10k: reset chip before reading chip_id in probe")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Offchannel management frames were failing:
[18099.253732] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18102.293686] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18105.333653] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18108.373712] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3780
[18111.413687] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18114.453726] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
[18117.493773] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e36c0
[18120.533631] ath10k_pci 0000:01:00.0: timed out waiting for offchannel skb cf0e3f00
This bug appears to have been added between 4.0 (which works for us),
and 4.4, which does not work.
I think this is because the tx-offchannel logic gets in a loop when
ath10k_mac_tx_frm_has_freq(ar) is false, so pkt is never actually
sent to the firmware for transmit.
This patch fixes the problem on 4.9 for me, and now HS20 clients
can work again with my firmware.
Antonio: tested with 10.4-3.5.3-00057 on QCA4019 and QCA9888
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Antonio Quartulli <antonio.quartulli@kaiwoo.ai>
[kvalo@codeaurora.org: improve commit log, remove unneeded parenthesis]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In a multiradio board with one QCA9984 and one AR9987
after enabling the crashdump with module parameter
coredump_mask=7, below backtrace is seen.
vmalloc: allocation failure: 0 bytes
kworker/u4:0: page allocation failure: order:0, mode:0x80d2
CPU: 0 PID: 6 Comm: kworker/u4:0 Not tainted 3.14.77 #130
Workqueue: ath10k_wq ath10k_core_register_work [ath10k_core]
(unwind_backtrace) from [<c021abf8>] (show_stack+0x10/0x14)
(dump_stack+0x80/0xa0)
(warn_alloc_failed+0xd0/0xfc)
(__vmalloc_node_range+0x1b4/0x1d8)
(__vmalloc_node+0x34/0x40)
(vzalloc+0x24/0x30)
(ath10k_coredump_register+0x6c/0x88 [ath10k_core])
(ath10k_core_register_work+0x350/0xb34 [ath10k_core])
(process_one_work+0x20c/0x32c)
(worker_thread+0x228/0x360)
This is due to ath10k_hw_mem_layout is not defined for AR9987.
For coredump undefined hw ramdump_size is 0.
Check for the ramdump_size before allocation memory.
Tested on: AR9987, QCA9984
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The IRAM start address in coredump was wrong for QCA9984, QCA4019, QCA9888 and
QCA99x0.
Tested on: QCA9984, QCA4019
FW version: 10.4-3.9.0.2-00044
Signed-off-by: Anilkumar Kolli <akolli@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since ath10k_mac_tx_push_txq() can be called from process context, we
must explicitly disable softirqs before the call into mac80211.
By calling ieee80211_tx_dequeue_ni() instead of ieee80211_tx_dequeue()
we make sure softirqs are always disabled even in the case when
ath10k_mac_tx_push_txq() is called from process context.
Calling ieee80211_tx_dequeue_ni() with softirq's already disabled
(e.g., from softirq context) should be safe as the local_bh_disable()
and local_bh_enable() functions (called from ieee80211_tx_dequeue_ni)
are fully reentrant.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Software version within WMI event ready message was displayed
in a not very useful decimal format. Change this info to be shown
in a hexadecimal format instead.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add vht_supp_mcs argument to service ready structure and print
supported MCS rates in WMI service ready debug message.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Displays lowest/highest supported channels for both 2ghz and 5ghz
bands as they're fetched within WMI service ready event.
These are shown in a frequency format.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add lowest/highest 2ghz channel arguments for use within WMI service
ready structure.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In ath10k_usb_hif_tx_sg the allocated urb should be released if
usb_submit_urb fails.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Recently, it has the basic feature of sdio tested success, so remove
it.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There are a bunch of spelling mistakes in two ath drivers, fix
these.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_bmi_write32 and ath10k_bmi_read32 can fail. The fix
checks their statuses to avoid potential undefined behaviors.
Signed-off-by: Kangjie Lu <kjlu@umn.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With the current implementation of wmi init command,
there is no provision for the host driver to provide mem
chunks addresses with more than 32-bit, to the firmware.
WCN3990 is a 35-bit target and can accept mem chunks addresses
which are above 32-bit.
If firmware supports address range more than 32 bit, it
advertises the support by setting the WMI_SERVICE_EXTEND_ADDRESS
service. Based on this service fill the upper bits of paddr while
providing the mem chunks in the wmi init command.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The peer param id for PEER_PARAM_USE_FIXED_PWR
is different for tlv and non-tlv firmware. This
causes incorrect peer param to be set by the driver
to the firmware(tlv/non-tlv).
Create seperate peer param map for tlv and non-tlv
firmware and attach the peer param id based on the
firmware type during the init.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
MSA memory region caries the hw descriptors information.
Dump MSA region in core dump as this is very helpful in debugging
hw issues.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
PMIC XO is the clock source for wifi rf clock in integrated wifi
chipset ex: WCN3990. Due to board layout errors XO frequency drifts
can cause wifi rf clock inaccuracy.
XO calibration test tree in Factory Test Mode is used to find the
best frequency offset(for example +/-2KHz )by programming XO trim
register. This ensure system clock stays within required 20 ppm
WLAN rf clock.
Retrieve the xo trim offset via system firmware (e.g., device tree),
especially in the case where the device doesn't have a useful EEPROM
on which to store the calibrated XO offset (e.g., for integrated Wifi).
Calibrated XO offset is sent to fw, which compensate the clock drift
by programing the XO trim register.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a spelling mistake in a ath10k_warn warning message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Bad latency is found on QCA988x, the issue was introduced by
commit 4504f0e5b5 ("ath10k: sdio: workaround firmware UART
pin configuration bug"). If uart_pin_workaround is false, this
change will set uart pin even if uart_print is false.
Tested HW: QCA9880
Tested FW: 10.2.4-1.0-00037
Fixes: 4504f0e5b5 ("ath10k: sdio: workaround firmware UART pin configuration bug")
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If 'sta->tdls' is false, no cleanup is executed, leading to memory/resource
leaks, e.g., 'arsta->tx_stats'. To fix this issue, perform cleanup before
go to the 'exit' label.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
driver sends QMI_WLFW_MSA_INFO_REQ_V01 QMI request to firmware
and in response expects range of addresses and size to be mapped.
Add condition to check whether addresses in response falls
under valid range otherwise return failure.
Testing: Tested on WCN3990 HW
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use ath10k_pci_soc_read32 / ath10k_pci_soc_write32 functions for
the rest of warm_reset functions. Until now these have been used
only for ath10k_pci_warm_reset_si0, but since they already exist
it makes sense to simplify code a bit.
Runtime tested with QCA9862.
Signed-off-by: Tomislav Požega <pozega.tomislav@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_bss_info_changed() handles various events from the upper layers. It
parses the changed bitfield and then configures the driver/firmware
accordingly. Each detected event is handled in a separate scope which is
independent of each other - but in the same function.
The commit f279294e9e ("ath10k: add support for configuring management
packet rate") changed this behavior by returning from this function
prematurely when some precondition was not fulfilled. All new event
handlers added after the BSS_CHANGED_BASIC_RATES event handler would then
also be skipped.
Signed-off-by: Sven Eckelmann <seckelmann@datto.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
No frequency is currently specified for the single clock defined in the
snoc driver, so the clock wrappers reimplements the standard bulk API
provided by the clock framework. Change to this.
The single clock defined is marked as optional so this version of the
get API is used, but might need to be reconsidered in the future.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regulator_get_optional() exists for cases where the driver needs do
behave differently depending on some regulator supply being present or
not, as we don't use this we can use the standard regulator_get() and
rely on its handling of unspecified regulators.
While the driver currently doesn't specify any loads the regulator
framework was updated last year to only account for load of enabled
regulators, so should the need appear it's better to apply load numbers
during initialization that dynamically.
With this the regulator wrappers have been reduced the become identical
to the standard bulk API provided by the regulator framework, so use
these instead of rolling our own.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The regulator operations is trying to set a voltage to a fixed value, by
giving some wiggle room. But some board designs specifies regulator
voltages outside this limited range. One such example is the Lenovo Yoga
C630, with vdd-3.3-ch0 in particular specified at 3.1V.
But consumers with fixed voltage requirements should just rely on the
board configuration to provide the power at the required level, so this
code should be removed.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The introduction of 768ec4c012 ("ath10k: update HOST capability QMI
message") served the purpose of supporting the new and extended HOST
capability QMI message.
But while the new message adds a slew of optional members it changes the
data type of the "daemon_support" member, which means that older
versions of the firmware will fail to decode the incoming request
message.
There is no way to detect this breakage from Linux and there's no way to
recover from sending the wrong message (i.e. we can't just try one
format and then fallback to the other), so a quirk is introduced in
DeviceTree to indicate to the driver that the firmware requires the 8bit
version of this message.
Cc: stable@vger.kernel.org
Fixes: 768ec4c012 ("ath10k: update HOST capability qmi message")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The tlv targets such as WCN3990 send more data in the chan info event, which is
not sent by the non tlv targets. There is a minimum size check in the wmi event
for non-tlv targets and hence we cannot update the common channel info
structure as it was done in commit 13104929d2 ("ath10k: fill the channel
survey results for WCN3990 correctly"). This broke channel survey results on
10.x firmware versions.
If the common channel info structure is updated, the size check for chan info
event for non-tlv targets will fail and return -EPROTO and we see the below
error messages
ath10k_pci 0000:01:00.0: failed to parse chan info event: -71
Add tlv specific channel info structure and restore the original size of the
common channel info structure to mitigate this issue.
Tested HW: WCN3990
QCA9887
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
10.2.4-1.0-00037
Fixes: 13104929d2 ("ath10k: fill the channel survey results for WCN3990 correctly")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the FW bundles multiple packets, pkt->act_len may be incorrect
as it refers to the first packet only (however, the FW will only
bundle packets that fit into the same pkt->alloc_len).
Before this patch, the skb length would be set (incorrectly) to
pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually
adjusted in ath10k_sdio_mbox_rx_process_packet.
The first problem is that ath10k_sdio_mbox_rx_process_packet does not
use proper skb_put commands to adjust the length (it directly changes
skb->len), so we end up with a mismatch between skb->head + skb->tail
and skb->data + skb->len. This is quite serious, and causes corruptions
in the TCP stack, as the stack tries to coalesce packets, and relies
on skb->tail being correct (that is, skb_tail_pointer must point to
the first byte_after_ the data).
Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet,
this moves the code to ath10k_sdio_mbox_rx_packet, and also add a
bounds check, as skb_put would crash the kernel if not enough space is
available.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Fixes: 8530b4e7b2 ("ath10k: sdio: set skb len for all rx packets")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
My wave-1 firmware often crashes when I am bringing down
AP vdevs, and sometimes at least some machines lockup hard
after spewing IOMMU errors.
I don't see the same issue in STA mode, so I suspect beacons
are the issue.
Moving the beacon buf deletion to later in the vdev teardown
logic appears to help this problem. Firmware still crashes
often, but several iterations did not show IOMMU errors and
machine didn't hang.
Tested hardware: QCA9880
Tested firmware: ath10k-ct from beginning of 2019, exact version unknown
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For sdio chip, if the rssi is not good, then it have some retry,
firmware will indicate the msdu list of a ppdu with a hole, it
means it lost the hole msdu, after the msdu retry from AP, the
hole msdu will indicate from firmware later. The hole msdu's PN
check will fail and the hole msdu will be dropped.
PN check fail example:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3818 6105 success
3819 6106 success
3820 6107 success
3817 6104 fail
The correct logic is reorder the msdu list and then do PN check.
ieee80211_rx_reorder_ampdu of mac80211 will do the reorer logic
and then do PN check in ieee80211_rx_h_decrypt of mac80211.
example after reorder:
Sequence number PN number PN check status
3814 6101 success
3815 6102 success
3816 6103 success
3817 6104 success
3818 6105 success
3819 6106 success
3820 6107 success
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00017-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For PMF case, the action,deauth,disassoc management need to encrypt
by hardware, it need to reserve 8 bytes for encryption, otherwise
the packet will be sent out with error format, then PMF case will
fail.
After add the 8 bytes, it will pass the PMF case.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This low level driver can find it useful to get the vif
when a remain on channel session is cancelled.
iwlwifi will need this soon.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Link: https://lore.kernel.org/r/20190723180001.5828-1-emmanuel.grumbach@intel.com
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
As clang points out, the vht_pfr is assigned to a struct member
without being initialized in one case:
drivers/net/wireless/ath/ath10k/mac.c:7528:7: error: variable 'vht_pfr' is used uninitialized whenever 'if' condition
is false [-Werror,-Wsometimes-uninitialized]
if (!ath10k_mac_can_set_bitrate_mask(ar, band, mask,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/mac.c:7551:20: note: uninitialized use occurs here
arvif->vht_pfr = vht_pfr;
^~~~~~~
drivers/net/wireless/ath/ath10k/mac.c:7528:3: note: remove the 'if' if its condition is always true
if (!ath10k_mac_can_set_bitrate_mask(ar, band, mask,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/wireless/ath/ath10k/mac.c:7483:12: note: initialize the variable 'vht_pfr' to silence this warning
u8 vht_pfr;
Add an explicit but probably incorrect initialization here.
I suspect we want a better fix here, but chose this approach to
illustrate the issue.
Fixes: 8b97b055dc ("ath10k: fix failure to set multiple fixed rate")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes checkpatch warnings:
drivers/net/wireless/ath/ath10k/pci.c:926: unnecessary cast may hide bugs, see http://c-faq.com/malloc/mallocnocast.html
drivers/net/wireless/ath/ath10k/pci.c:1072: unnecessary cast may hide bugs, see http://c-faq.com/malloc/mallocnocast.html
While at it, also remove unnecessary initialisation of data_buf variable in both cases.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes checkpatch warning:
drivers/net/wireless/ath/ath10k/swap.c:110: Possible unnecessary 'out of memory' message
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The workqueue need to flush and destory while remove sdio module,
otherwise it will have thread which is not destory after remove
sdio modules.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k will receive some message with invalid peer id from firmware.
reason is:
There are incoming frames to MAC hardware that NOT find relative
address search table, then peer id is invalid set by MAC hardware,
it is hardware's logic, so fix it in ath10k will be more convenient.
log:
ath10k_sdio mmc1:0001:1: Got RX ind from invalid peer: 65535
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the memory allocated for qmi handle is
not being freed during de-init which leads to memory leak.
Free the allocated qmi memory in qmi deinit
to avoid memory leak.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-01040-QCAHLSWMTPLZ-1
Fixes: fda6fee0001e ("ath10k: add QMI message handshake for wcn3990 client")
Signed-off-by: Dundi Raviteja <dundi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
It report error message while suspend/resume test.
dmesg log:
[ 150.749962] ath10k_sdio mmc1:0001:1: hif read32 not supported
[ 150.755728] ath10k_sdio mmc1:0001:1: failed to set coverage class: expected integer microsecond value in register
Reason is sdio chip does not support set_coverage_class as well as
pcie chip, remove the set_coverage_class handler will avoid it.
callstack of the error message:
OUTLINED_FUNCTION_6+0xc/0x14 [ath10k_core]
ath10k_mac_op_set_coverage_class+0x2c/0x40 [ath10k_core]
ieee80211_reconfig+0x5d0/0x108c [mac80211]
ieee80211_resume+0x34/0x6c [mac80211]
wiphy_resume+0xbc/0x13c [cfg80211]
dpm_run_callback+0xa4/0x168
device_resume+0x1d4/0x200
async_resume+0x1c/0x34
async_run_entry_fn+0x48/0xf8
process_one_work+0x178/0x2f8
worker_thread+0x1d8/0x2cc
kthread+0x11c/0x12c
ret_from_fork+0x10/0x18
the error log will not happen after this patch applied.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit ec8f24b7fa ("treewide: Add SPDX license identifier -
Makefile/Kconfig") marked various Makefiles and Kconfig files within ath
directories as GPL-2.0. But these modules and drivers are actually ISC:
* ath
* ar5523
* ath10k
* ath5k
* ath6kl
* ath9k
* wcn36xx
* wil6210
Fix SPDX tags accordingly.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Integrated WiFi chipset ex:WCN399x supports fw logging
using WMI copy engine and shared mem DIAG based fw logging.
By default shared mem DIAG based fw logging is enabled.
To support WMI copy engine based fw logging add QMI
control message to enable WMI copy engine based fw logging.
Enable WMI based fw logging using fw_diag_log module parameter.
insmod ath10k_core.ko fw_diag_log=1
DIAG utility(https://github.com/andersson/diag) implements extraction
of diagnostics related messages between application processor and
various subsystems while shared mem DIAG based fw logging is enabled.
Testing: Tested on WCN3990/QCA6174 HW
Tested FW: WLAN.HL.3.1-00959-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware will report flag with HTT_RX_IND_MPDU_STATUS_TKIP_MIC_ERR
if MIC error, the flag will be used in mac80211.
ieee80211_rx_h_michael_mic_verify will check the flag and start TKIP
countermeasures.
Now countermeasure tests pass both with WPA only and WPA2/WPA mixed
mode.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This patch will add the support to control the transmit power for traffic
to a station associated with the AP.
Underlying firmware will enforce that the maximum tx power will be based
on the regulatory requirements. If the user given transmit power is greater
than the allowed tx power in the given channel, then the firmware will use
the maximum tx power in the same channel.
Max and Min tx power values will depends on no of tx chain masks,
for QCA9984 allowed tx power range values from 6 to 23.
When 0 is sent to the firmware as tx power, it will revert to the default
tx power for the station.
Tested Hardware : QCA9984
Tested Firmware : 10.4-3.9.0.2-00046
Co-developed-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Ashok Raj Nagarajan <arnagara@codeaurora.org>
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Peer creation in firmware fails if last peer deletion is still
in progress.
The firmware sends a peer delete response event if it advertises
the service WMI_SERVICE_SYNC_DELETE_CMDS. This peer delete response
event is used to synchronize the peer deletion.
Add peer delete response event and wait for the event after
deleting every peer from host driver to synchronize with firmware.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Dundi Raviteja <dundi@codeaurora.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When we add an interface immediately after removing
the interface the vdev deletion in firmware might not
have been completed. We need to synchronize the vdev creation
with the firmware.
Wait for vdev delete response from firmware when we
remove an interface.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Observed PCIE device wake up failed after ~120 iterations of
soft-reboot test. The error message is
"ath10k_pci 0000:01:00.0: failed to wake up device : -110"
The call trace as below:
ath10k_pci_probe -> ath10k_pci_force_wake -> ath10k_pci_wake_wait ->
ath10k_pci_is_awake
Once trigger the device to wake up, we will continuously check the RTC
state until it returns RTC_STATE_V_ON or timeout.
But for QCA99x0 chips, we use wrong value for RTC_STATE_V_ON.
Occasionally, we get 0x7 on the fist read, we thought as a failure
case, but actually is the right value, also verified with the spec.
So fix the issue by changing RTC_STATE_V_ON from 0x5 to 0x7, passed
~2000 iterations.
Tested HW: QCA9984
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, below fixed rate commands are broken,
iw wlanx set bitrates legacy-<2.4|5> ht-mcs-<2.4|5> vht-mcs-<2.4|5> \
<NSS:MCSx>
iw wlanx set bitrates legacy-<2.4|5> <legacy rate> ht-mcs-<2.4|5> \
vht-mcs-<2.4|5> <NSS:MCSx>
There are two methods to set fixed rate, both failed,
- Use vdev fixed rate command
This command only support one single rate, but it's broken due to
mac80211 change commit e8e4f5280d ("mac80211: reject/clear user
rate mask if not usable"), which requires user to specify at least
one legacy rate. So we can't use this command to set ht/vht single
rate any more.
- Use peer_assoc command
This command can update rx capability for multiple rates, it will
work fine for ht mcs rates, as each supported mcs can be advertised
in ht_mcs index mask. But this will not work with vht rates because,
as per the vht mcs capability advertisement, there are only two bits
to indicate the supported mcs. E.g. only support 0-7, 0-8, 0-9.
So introduced new WMI command: WMI_PEER_PARAM_FIXED_RATE. After peer
assoc, the peer fixed rate cmd will work for that specific peer.
Remaining peers will use auto rate. If both vdev fixed rate and peer
fixed rates are given, peer fixed rate will take effect to peers for
which this cmd is given. Remaining peers in that vdev, will use vdev
fixed rate.
Tested HW: QCA9984
Tested FW: 10.4-3.9.0.2-00035
Signed-off-by: Miaoqing Pan <miaoqing@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The "WARNING" string confuses syzbot, which thinks it found
a crash [1].
Change the string to avoid such problem.
[1] https://lkml.org/lkml/2019/5/9/243
Reported-by: syzbot+c1b25598aa60dcd47e78@syzkaller.appspotmail.com
Suggested-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In function ath10k_sdio_mbox_rx_alloc() [sdio.c],
ath10k_sdio_mbox_alloc_rx_pkt() is called without handling the error cases.
This will make the driver think the allocation for skb is successful and
try to access the skb. If we enable failslab, system will easily crash with
NULL pointer dereferencing.
Call trace of CONFIG_FAILSLAB:
ath10k_sdio_irq_handler+0x570/0xa88 [ath10k_sdio]
process_sdio_pending_irqs+0x4c/0x174
sdio_run_irqs+0x3c/0x64
sdio_irq_work+0x1c/0x28
Fixes: d96db25d20 ("ath10k: add initial SDIO support")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For QCA988X target, pktlog gives details of the tx bitrate
which is used in the driver for station info.
Enabling pktlog by default will cause more interrupts
in target to host CE pipe, which can impact more CPU usage
for targets ex:WCN3990 and also not required for all other
platforms (eg: WCN3990), for getting tx bitrate.
Enable pktlog only for QCA988X based on hardware params.
Tested HW : WCN3990
Tested FW : WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e8123bb74c ("ath10k: add per peer tx stats support for 10.2.4")
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Lockdep warns at lockdep_assert_held(&ar->data_lock) in
ath10k_htt_rx_pn_check_replay_hl(). Acquire ar->data_lock before calling
ath10k_htt_rx_pn_check_replay_hl() to fix it.
Call trace:
ath10k_htt_rx_pn_check_replay_hl+0x118/0x134 [ath10k_core]
ath10k_htt_rx_proc_rx_ind_hl+0xd8/0x250 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x148/0xf30 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x24/0x40 [ath10k_core]
ath10k_sdio_irq_handler+0x374/0xaa4 [ath10k_sdio]
Fixes: 130c774957 ("ath10k: add PN replay protection for high latency devices")
Signed-off-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Firmware name for UTF mode of SDIO has changed from utf-2.bin to
utf-sdio-2.bin, so it need to change in ath10k, otherwise it will
fail for UTF mode.
After change the name in ath10k, it will success for UTF mode of
SDIO/USB.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The command to simulate firmware crash:
echo soft > /sys/kernel/debug/ieee80211/phy0/ath10k/simulate_fw_crash
It will send WMI_FORCE_FW_HANG_ASSERT to firmware, then it will trigger
CPU interrupt status register for SDIO chip, ath10k driver need to
configure it while enable SDIO interrupt, otherwise ath10k driver will
not get the assert error info.
After this change, it will success for simulate firmware crash.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_dbg() is called in ath10k_process_rx() with huge set of arguments
which is causing CPU overhead even when debug_mask is not set.
Good improvement was observed in the receive side performance when call
to ath10k_dbg() is avoided in the RX path.
Since currently all debug messages are sent via tracing infrastructure,
we cannot entirely avoid calling ath10k_dbg. Therefore, call to
ath10k_dbg() is made conditional based on tracing config in the driver.
Trasmit performance remains unchanged with this patch; below are some
experimental results with this patch and tracing disabled.
mesh mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP 840Mbps 76.53% 960Mbps 78.14%
UDP 1030Mbps 74.58% 1132Mbps 74.31%
Infra mode:
w/o this patch with this patch
Traffic TP CPU Usage TP CPU usage
TCP Rx 1241Mbps 80.89% 1270Mbps 73.50%
UDP Rx 1433Mbps 81.77% 1472Mbps 72.80%
Tested platform : IPQ8064
hardware used : QCA9984
firmware ver : ver 10.4-3.5.3-00057
Signed-off-by: Kan Yan <kyan@chromium.org>
Signed-off-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Without this op, it will not be possible to configure aggregation for
high latency devices.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is done in order to make the *htt_h2t_aggr_cfg_msg* op align better
with the rest of the htt ops (whom all have inline wrappers).
It also adds support for the case when the op is missing (function
pointer is NULL).
As a result of this, the name of the 32 bit implementation in htt_tx.c
was changed and the function was made static.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
tx_stats will be freed and set to NULL before debugfs_sta node is
removed in station disconnetion process. So if read the debugfs_sta
node there may be NULL pointer error. Add check for tx_stats before
use it to resove this issue.
Signed-off-by: Yingying Tang <yintang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For some SDIO chip, the peer id is 65535 for MPDU with error status,
then test_bit will trigger buffer overflow for peer's memory, if kasan
enabled, it will report error.
Reason is when station is in disconnecting status, firmware do not delete
the peer info since it not disconnected completely, meanwhile some AP will
still send data packet to station, then hardware will receive the packet
and send to firmware, firmware's logic will report peer id of 65535 for
MPDU with error status.
Add check for overflow the size of peer's peer_ids will avoid the buffer
overflow access.
Call trace of kasan:
dump_backtrace+0x0/0x2ec
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xc8/0xec
print_address_description+0x74/0x240
kasan_report+0x250/0x26c
__asan_report_load8_noabort+0x20/0x2c
ath10k_peer_find_by_id+0x180/0x1e4 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x100c/0x2fd4 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x20/0x34 [ath10k_core]
ath10k_sdio_irq_handler+0xcc8/0x1678 [ath10k_sdio]
process_sdio_pending_irqs+0xec/0x370
sdio_run_irqs+0x68/0xe4
sdio_irq_work+0x1c/0x28
process_one_work+0x3d8/0x8b0
worker_thread+0x508/0x7cc
kthread+0x24c/0x264
ret_from_fork+0x10/0x18
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 firmware advertises the service WMI_TLV_SERVICE_MESH_11S
for mesh 11s. Map this wmi tlv service to enable mesh 11s
for WCN3990.
Tested HW: WCN3990
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently mac80211 do not support probe response template for
mesh point. When WMI_SERVICE_BEACON_OFFLOAD is enabled, host
driver tries to configure probe response template for mesh, but
it fails because the interface type is not NL80211_IFTYPE_AP but
NL80211_IFTYPE_MESH_POINT.
To avoid this failure, skip sending probe response template to
firmware for mesh point.
Tested HW: WCN3990/QCA6174/QCA9984
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a disparity in wmi and wmi tlv vdev subtype
enum for WMI_VDEV_SUBTYPE_MESH_11S.
Add different enum for wmi tlv vdev subtype to support
vdev of subtype mesh 11s for WCN3990.
Tested HW: WCN3990
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
For SDIO chip, it does not have HTT connect step in boot phase of UTF
mode, so it does not need the swap configuration for UTF mode, otherwise
it will trigger UTF load fail. For normal mode, it is swap between HTT
and WMI, for UTF mode, it does not have HTT, so it can not swap between
HTT and WMI.
Disable swap mail box for UTF mode will let UTF mode load success.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The enum value for WMI_TLV_STAT_PDEV, WMI_TLV_STAT_VDEV
and WMI_TLV_STAT_PEER is wrong, due to which the vdev stats
are not received from firmware in wmi_update_stats event.
Fix the enum values for above stats to receive all stats
from firmware in WMI_TLV_UPDATE_STATS_EVENTID.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: f40a307eb9 ("ath10k: Fill rx duration for each peer in fw_stats for WCN3990)
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, replace code of the following form:
sizeof(*ce_hdr) + CE_COUNT * sizeof(ce_hdr->entries[0])
with:
struct_size(ce_hdr, entries, CE_COUNT)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes, in particular in the
context in which this code is being used.
So, change the following form:
sizeof(*rx) + (sizeof(struct htt_rx_indication_mpdu_range) * num_mpdu_ranges)
to :
struct_size(rx, mpdu_ranges, num_mpdu_ranges)
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently the protected management frames are
not appended with the MIC_LEN which results in
the protected management frames being encoded
incorrectly.
Add the extra space at the end of the protected
management frames to fix this encoding error for
the protected management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da4973 ("ath10k: wmi: add management tx by reference support over wmi")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently instant rx_duration always fetching as zero
in fw_stats debugfs entry if extended peer stats event
supports.
This patch updates instant rx_duration in fw_stats entry
based on extended peer stats and maintaining backward
compatibility for 10.2/10.x.
Tested HW: QCA9984.
Tested FW: 10.4-3.6.0.1-00004.
Signed-off-by: Balaji Pothunoori <bpothuno@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In tx_stats debugfs, txrate->flags may contain multiple bits. For
example, RATE_INFO_FLAGS_SHORT_GI could be set, and tx stats bytes
and packets will be not updated correctly.
Fix this issue by using bit operation to check txrate->flags.
Tested HW: QCA9984
Tested Firmware: 10.4-3.9.0.1-00007
Signed-off-by: Brandon Huang <yanghuan@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
CE4 is host to target HTT tx pipe, tx completion are not served
on time when CPU is loaded and this cause ce src ring full condition
due to less no of src buffer entries.
To mitigate the issue increase CE4 src buffer entries to 2048.
Testing:
Tested on QCS404 platform(WCN3990 HW)
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Board id and fw version is not printed by default in qmi
cap response message. Move board id and fw version logging
to info level for default logging.
[ 34.005399] ath10k_snoc a000000.wifi: qmi chip_id 0x30b chip_family 0x4001 board_id 0xff soc_id 0x40070000
[ 34.005432] ath10k_snoc a000000.wifi: qmi fw_version 0x3106836b fw_build_timestamp 2019-02-13 10:24 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HL.3.1-00875-QCAHLSWMTPL-1
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reset HTT stats helps to get the aggregated HTT stats via
tracing and also we can clear the accumulated HTT stats with
this debugfs file.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Extended the bit mask value of the HTT stats to get the Mu-MIMO
related stats via tracing.
Signed-off-by: Maharaja Kennadyrajan <mkenna@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Invalid rate code is sent to firmware when multicast rate value of 0 is
sent to driver indicating disabled case, causing broken mesh path.
so fix that.
Tested on QCA9984 with firmware 10.4-3.6.1-00827
Sven tested on IPQ4019 with 10.4-3.5.3-00057 and QCA9888 with 10.4-3.5.3-00053
(ath10k-firmware) and 10.4-3.6-00140 (linux-firmware 2018-12-16-211de167).
Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Co-developed-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Zhi Chen <zhichen@codeaurora.org>
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Tested-by: Sven Eckelmann <sven@narfation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After implementing PN replay check we can enable SDIO support on QCA6174.
Tested with client mode on all security modes, and fragmentation as well. AP
mode does not work yet.
Also tone down the warning about SDIO being not ready yet.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1. AP mode
is not working yet.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not handle fragmented frames and
all fragmented frames on receive path were lost in ath10k. Even a simple ping
test failed with fragmentation.
The fragmented packets are decapsulated based on the security mode, then the PN
is checked and the fragmented frame is passed to mac80211. mac80211 in
ieee80211_rx_h_defragment() will then combine the fragment frames and forward
to upper layers.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On high latency devices (SDIO, USB) ath10k did not do PN replay check, a data
frame with an invalid PN number was not discard as it should have been. So this
patch implements PN replay in ath10k. PN replay check for fragmented frames is
implemented in followup patch.
With low latency devices (PCI, AHB) hardware can store the data
frames's content to host memory directly and the firmware can fully reorder
data frames, and do PN replay check at the same time. But for high latency
devices all data frames will be received and stored in firmware's memory and it
is hard to do full reorder because of the memory size limitations in the
firmware. This is why the PN replay protections needs to be implemented in host
driver.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the handler for HTT_T2H_MSG_TYPE_SEC_IND event from firmware, which stores
PN for replay check implemented in the following patch.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Add the struct for PN replay protection and fragment packet
handler.
Also fix the bitmask of HTT_RX_DESC_HL_INFO_MCAST_BCAST to match what's currently
used by SDIO firmware. The defines are not used yet so it's safe to modify
them. Remove the conflicting HTT_RX_DESC_HL_INFO_FRAGMENT as
it's not either used in ath10k.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k_mac_vif_chan() always returns an error for the given vif
during system-wide resume which reliably triggers two WARN_ON()s
in ath10k_bss_info_changed() and they are not particularly
useful in that code path, so drop them.
Tested: QCA6174 hw3.2 PCI with WLAN.RM.2.0-00180-QCARMSWPZ-1
Tested: QCA6174 hw3.2 SDIO with WLAN.RMH.4.4.1-00007-QCARMSWP-1
Fixes: cd93b83ad9 ("ath10k: support for multicast rate control")
Fixes: f279294e9e ("ath10k: add support for configuring management packet rate")
Cc: stable@vger.kernel.org
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Tested-by: Claire Chang <tientzu@chromium.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE
polling") introduced a regression where we try to sleep (grab a mutex)
in an atomic context:
[ 233.602619] BUG: sleeping function called from invalid context at kernel/locking/mutex.c:254
[ 233.602626] in_atomic(): 1, irqs_disabled(): 0, pid: 0, name: swapper/0
[ 233.602636] CPU: 0 PID: 0 Comm: swapper/0 Tainted: G W 5.1.0-rc2 #4
[ 233.602642] Hardware name: Google Scarlet (DT)
[ 233.602647] Call trace:
[ 233.602663] dump_backtrace+0x0/0x11c
[ 233.602672] show_stack+0x20/0x28
[ 233.602681] dump_stack+0x98/0xbc
[ 233.602690] ___might_sleep+0x154/0x16c
[ 233.602696] __might_sleep+0x78/0x88
[ 233.602704] mutex_lock+0x2c/0x5c
[ 233.602717] ath10k_pci_diag_read_mem+0x68/0x21c [ath10k_pci]
[ 233.602725] ath10k_pci_diag_read32+0x48/0x74 [ath10k_pci]
[ 233.602733] ath10k_pci_dump_registers+0x5c/0x16c [ath10k_pci]
[ 233.602741] ath10k_pci_fw_crashed_dump+0xb8/0x548 [ath10k_pci]
[ 233.602749] ath10k_pci_napi_poll+0x60/0x128 [ath10k_pci]
[ 233.602757] net_rx_action+0x140/0x388
[ 233.602766] __do_softirq+0x1b0/0x35c
[...]
ath10k_pci_fw_crashed_dump() is called from NAPI contexts, and firmware
memory dumps are retrieved using the diag memory interface.
A simple reproduction case is to run this on QCA6174A /
WLAN.RM.4.4.1-00132-QCARMSWP-1, which happens to be a way to b0rk the
firmware:
dd if=/sys/kernel/debug/ieee80211/phy0/ath10k/mem_value bs=4K count=1
of=/dev/null
(NB: simulated firmware crashes, via debugfs, don't trigger firmware
dumps.)
The fix is to move the crash-dump into a workqueue context, and avoid
relying on 'data_lock' for most mutual exclusion. We only keep using it
here for protecting 'fw_crash_counter', while the rest of the coredump
buffers are protected by a new 'dump_mutex'.
I've tested the above with simulated firmware crashes (debugfs 'reset'
file), real firmware crashes (the 'dd' command above), and a variety of
reboot and suspend/resume configurations on QCA6174A.
Reported here:
http://lkml.kernel.org/linux-wireless/20190325202706.GA68720@google.com
Fixes: 25733c4e67 ("ath10k: pci: use mutex for diagnostic window CE polling")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We currently have two levels of strict validation:
1) liberal (default)
- undefined (type >= max) & NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
- garbage at end of message accepted
2) strict (opt-in)
- NLA_UNSPEC attributes accepted
- attribute length >= expected accepted
Split out parsing strictness into four different options:
* TRAILING - check that there's no trailing data after parsing
attributes (in message or nested)
* MAXTYPE - reject attrs > max known type
* UNSPEC - reject attributes with NLA_UNSPEC policy entries
* STRICT_ATTRS - strictly validate attribute size
The default for future things should be *everything*.
The current *_strict() is a combination of TRAILING and MAXTYPE,
and is renamed to _deprecated_strict().
The current regular parsing has none of this, and is renamed to
*_parse_deprecated().
Additionally it allows us to selectively set one of the new flags
even on old policies. Notably, the UNSPEC flag could be useful in
this case, since it can be arranged (by filling in the policy) to
not be an incompatible userspace ABI change, but would then going
forward prevent forgetting attribute entries. Similar can apply
to the POLICY flag.
We end up with the following renames:
* nla_parse -> nla_parse_deprecated
* nla_parse_strict -> nla_parse_deprecated_strict
* nlmsg_parse -> nlmsg_parse_deprecated
* nlmsg_parse_strict -> nlmsg_parse_deprecated_strict
* nla_parse_nested -> nla_parse_nested_deprecated
* nla_validate_nested -> nla_validate_nested_deprecated
Using spatch, of course:
@@
expression TB, MAX, HEAD, LEN, POL, EXT;
@@
-nla_parse(TB, MAX, HEAD, LEN, POL, EXT)
+nla_parse_deprecated(TB, MAX, HEAD, LEN, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression NLH, HDRLEN, TB, MAX, POL, EXT;
@@
-nlmsg_parse_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
+nlmsg_parse_deprecated_strict(NLH, HDRLEN, TB, MAX, POL, EXT)
@@
expression TB, MAX, NLA, POL, EXT;
@@
-nla_parse_nested(TB, MAX, NLA, POL, EXT)
+nla_parse_nested_deprecated(TB, MAX, NLA, POL, EXT)
@@
expression START, MAX, POL, EXT;
@@
-nla_validate_nested(START, MAX, POL, EXT)
+nla_validate_nested_deprecated(START, MAX, POL, EXT)
@@
expression NLH, HDRLEN, MAX, POL, EXT;
@@
-nlmsg_validate(NLH, HDRLEN, MAX, POL, EXT)
+nlmsg_validate_deprecated(NLH, HDRLEN, MAX, POL, EXT)
For this patch, don't actually add the strict, non-renamed versions
yet so that it breaks compile if I get it wrong.
Also, while at it, make nla_validate and nla_parse go down to a
common __nla_validate_parse() function to avoid code duplication.
Ultimately, this allows us to have very strict validation for every
new caller of nla_parse()/nlmsg_parse() etc as re-introduced in the
next patch, while existing things will continue to work as is.
In effect then, this adds fully strict validation for any new command.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although not likely, the bundle allocation might fail.
Add proper error check and warning print.
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTC header carries junk values that may be interpreted by the firmware
differently. Enable credit update only if flow control is enabled for
the corresponding endpoint.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Erik Stromdahl <erik.stromdahl@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With SDIO there's a use after free after a data frame is transfered, call stack
below. This happens because ath10k_htt_tx_hl() directly transmits the skb
provided by mac80211 using ath10k_htc_send(), all other HTT functions use
separate skb created with ath10k_htc_alloc_skb() to transmit the HTC packet.
After the packet is transmitted mac80211 frees the skb in ieee80211_tx_status()
but HTT layer expects that it still owns the skb, and frees it in
ath10k_htt_htc_tx_complete().
To fix this take a reference of skb before sending it to HTC layer to make sure
we still own the skb.
Tested on QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
ath10k_htt_tx_hl() is only used by SDIO and USB so other busses (PCI, AHB and
SNOC) should be unaffected.
call stack of use-after-free:
dump_backtrace+0x0/0x2d8
show_stack+0x20/0x2c
__dump_stack+0x20/0x28
dump_stack+0xc8/0xec
print_address_description+0x74/0x240
kasan_report+0x258/0x274
__asan_report_load4_noabort+0x20/0x28
skb_pull+0xbc/0x114
ath10k_htc_notify_tx_completion+0x190/0x2a4 [ath10k_core]
ath10k_sdio_write_async_work+0x1e4/0x2c4 [ath10k_sdio]
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18
Allocated by one task:
kasan_kmalloc+0xa0/0x13c
kasan_slab_alloc+0x14/0x1c
kmem_cache_alloc+0x144/0x208
__alloc_skb+0xec/0x394
alloc_skb_with_frags+0x8c/0x374
sock_alloc_send_pskb+0x520/0x5d4
sock_alloc_send_skb+0x40/0x50
__ip_append_data+0xf5c/0x1858
ip_make_skb+0x194/0x1d4
udp_sendmsg+0xf24/0x1ab8
inet_sendmsg+0x1b0/0x2e0
sock_sendmsg+0x88/0xa0
__sys_sendto+0x220/0x3a8
__arm64_sys_sendto+0x78/0x80
el0_svc_common+0x120/0x1e0
el0_svc_compat_handler+0x64/0x80
el0_svc_compat+0x8/0x18
Freed by another task:
__kasan_slab_free+0x120/0x1d4
kasan_slab_free+0x10/0x1c
kmem_cache_free+0x74/0x504
kfree_skbmem+0x88/0xc8
__kfree_skb+0x24/0x2c
consume_skb+0x114/0x18c
__ieee80211_tx_status+0xb7c/0xf60 [mac80211]
ieee80211_tx_status+0x224/0x270 [mac80211]
ath10k_txrx_tx_unref+0x564/0x950 [ath10k_core]
ath10k_htt_t2h_msg_handler+0x178c/0x2a38 [ath10k_core]
ath10k_htt_htc_t2h_msg_handler+0x20/0x30 [ath10k_core]
ath10k_sdio_irq_handler+0xcc0/0x1654 [ath10k_sdio]
process_sdio_pending_irqs+0xec/0x358
sdio_run_irqs+0x68/0xe4
sdio_irq_work+0x1c/0x28
process_one_work+0x3d8/0x8b0
worker_thread+0x518/0x7e0
kthread+0x260/0x278
ret_from_fork+0x10/0x18
Reported-by: Wen Gong <wgong@codeaurora.org>
Tested-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Transmit completion for SDIO is similar to PCIe, modify the high
latency path to allow SDIO modules to use the msdu id.
kvalo: the original patch from Alagu enabled this only for SDIO but I'm not
sure should we also enable this with USB. I'll use bus params to enable this
for so that it's easy to enable also for USB later.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This way we don't need to set every variable and give them to default, which is
zero. This is also safer in case we forgot to initalise a new field in some of
the bus modules.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HTT High Latency (ATH10K_DEV_TYPE_HL) does not use txdone_fifo at all, we don't
even initialise it by skipping ath10k_htt_tx_alloc_buf() in
ath10k_htt_tx_start(). Because of this using QCA6174 SDIO
ath10k_htt_rx_tx_compl_ind() will crash when it accesses unitialised
txdone_fifo. So skip txdone_fifo when using High Latency mode.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Disabling interrupts this early meant WMI communication was not working anymore
when the SDIO device was removed. But we call ath10k_core_unregister() that
will eventually call ath10k_sdio_hif_stop(), which disables the interrupts. So
there's actually no need to disable interrupts here.
Also remove cancel_work_sync() as it's also called in ath10k_sdio_hif_stop().
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
On QCA6174 SDIO devices the SDIO interrupt will fail if UART is
disabled from ath10k. SDIO firmware enables UART printouts by
default. If ath10k will try to enable UART again the firmware
will configure it's GPIO line incorrectly and SDIO interrupts
won't work anymore. The workaround is to set UART pin again (19
for QCA6174 SDIO) if uart_print is 0.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently there is no way for the driver to signal to mac80211 that it should
schedule a TXQ even if there are no packets on the mac80211 part of that queue.
This is problematic if the driver has an internal retry queue to deal with
software A-MPDU retry.
This patch changes the behavior of ieee80211_schedule_txq to always schedule
the queue, as its only user (ath9k) seems to expect such behavior already:
it calls this function on tx status and on powersave wakeup whenever its
internal retry queue is not empty.
Also add an extra argument to ieee80211_return_txq to get the same behavior.
This fixes an issue on ath9k where tx queues with packets to retry (and no
new packets in mac80211) would not get serviced.
Fixes: 89cea7493a ("ath9k: Switch to mac80211 TXQ scheduling and airtime APIs")
Signed-off-by: Felix Fietkau <nbd@nbd.name>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Currently, rx_duration for each peer is not getting populated in
fw_stats debugfs entry for WCN3990.
WCN3990 firmware sends rx duration for each peer as part of
peer_extd_stats in WMI_UPDATE_STATS_EVENT. To enable peer_extd_stats,
firmware expects host to send fw_stats_req_mask with flag
WMI_TLV_PEER_STATS_EXTD set in WMI_REQUEST_STATS_CMD.
Send fw_stats_req_mask with flag WMI_TLV_PEER_STATS_EXTD set in
WMI_REQUEST_STATS_CMD and parse the peer_extd_stats in
WMI_UPDATE_STATS_EVENT to populate the rx_duration of each peer
in fw_stats debugfs entry.
Currently the driver handles 32-bit rx_duration, but the rx_duration
for WCN3990 can be upto 63 bit. The firmware sends rx_duration split
into two 32-bit fields, with the upper 32-bits being valid only if its
MSB is set. This change handles the 63-bit rx_duration obtained from
WCN3990 and maintain the backward compatibility.
To get the rx_duration of each connected peer :
cat /sys/kernel/debug/ieee80211/phyX/ath10k/fw_stats
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ht_idx (ht rate index) and idx (rate table index) are calculated based on
mcs index. This mcs index used in the above calculation should be 0-9 for
getting the correct ht_idx and idx.
Currently the mcs index used for the above calculations is mcs index which
can be 0-31 (in case of HT), leading to incorrect rate index and ht index values.
Fix the issue by obtaining mcs value from the ratecode reported by firmware
and use it for calculating ht_idx and idx (rate-table index).
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: e88975ca37 ("ath10k: dump tx stats in rate table format")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SGI is updated wrongly in tx stats table in debugfs per sta
entry. To know whether the packets/bytes are sent with SHORT GI,
test whether the SGI bit(ATH10K_RATE_INFO_FLAGS_SGI_BIT) is set or
not in the txrate flags.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently, the bandwidth is updated wrongly in BW table in tx_stats
debugfs per sta as there is difference in number of bandwidth type
in mac80211 and driver stats table. This leads to bandwidth getting
updated at wrong index in bandwidth table in tx_stats.
Fix this index mismatch between mac80211 and driver stats table (BW table)
by making the number of bandwidth type in driver compatible with mac80211.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The NSS data is updated incorrectly in the tx stats as the array
indexing starts from zero.
Fix the incorrect updation of NSS data in tx_stats by taking into
consideration the array index starting from zero.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: a904417fc8 ("ath10k: add extended per sta tx statistics support")
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 firmware versions WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1 & onwards
supports maximum 33 peers including self peer. To support maximum peers,
send updated peer param to firmware during initialization.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The calibration data fetch will trigger sdio error, then sdio will
become fail untill reboot system.
If happens when run ifconfig wlan down, then ifconfig wlan up will
fail untill reboot system.Remove it fix the ifconfig wlan issue.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The length of wmi tlv command for management tx send is calculated
incorrectly in case of protected management frames as there is addition
of IEEE80211_CCMP_MIC_LEN twice. This leads to improper behaviour of
firmware as the wmi tlv mgmt tx send command for protected mgmt frames
is formed wrongly.
Fix the length calculation of wmi tlv command for mgmt tx send in case
of protected management frames by adding the IEEE80211_CCMP_MIC_LEN only
once.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Fixes: 1807da4973 "ath10k: wmi: add management tx by reference support over wmi"
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware does not provide RSSI value to the host, it's only set to
zero. In that case don't report the value to mac80211. One risk here is that
value zero might be a valid value with other firmware, currently there's no way
to detect that.
Without the fix, the rssi value indicated by iw changes between the actual
value and -95.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The target device needs to be reset during power_down(), otherwise only the
first power_up() will work. And as ath10k calls power_up() during driver
initialisation the driver would be otherwise unusable.
Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware may turn it on based on scratch registers so disable the
firmware log to avoid that.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The SDIO firmware does not allow transmitting packets with the
reduced tx completion HI_ACS option. SDIO firmware uses 1544 as
alternate credit size, which is not big enough for the maximum sized
mac80211 frames. Disable both these HI_ACS flags for SDIO.
Co-developed-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
This is a theoretical fix, the issue is found in code review.
When adding the host memory chunks into wmi-tlv init command,
there is no separate tlv header for each host memory chunk
in the struct array, which breaches the convention between
host and firmware, will result in mismatch between the two.
To fix this issue, add separate tlv headers for the host
memory chunks in wmi-tlv init command.
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Currently after enabling the WMI debug logging,
there is no detail printed about the param id
and the param value for the pdev, vdev and
peer params which are set.
Enhance the WMI logging to print the param id
and the param value for pdev, vdev and peer set
param wmi commands.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "data" tx completion event. Host extracts ack rssi
values of data packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
In WCN3990, WMI_TLV_SERVICE_TX_DATA_MGMT_ACK_RSSI service Indicates that
the firmware has the capability to send the RSSI value of the ACK for all
data and management packets transmitted.
If WMI_RSRC_CFG_FLAG_TX_ACK_RSSI is set in host capability then firmware
sends RSSI value in "management" tx completion event. Host extracts ack
rssi values of management packets from their tx completion event.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When the driver receives the tx completion of the
descriptor over ce, it clears the nbytes configured
for that particular descriptor. WCN3990 uses ce
descriptors with 64-bit address.
Currently during handling the tx completion of the
descriptors, the nbytes are accessed from the descriptors
using ce_desc for 32-bit targets. This will lead to clearing
of memory at incorrect offset if DMA MASK is set to greater
than 32 bits.
Attach different ce tx copy completed handler for targets
using address above 32-bit address.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01387-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Use SPDX identifiers everywhere in ath10k.
Makefile was incorrectly marked in commit b24413180f ("License cleanup: add
SPDX GPL-2.0 license identifier to files with no license"), fix that as well.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Instead of copying fields one by one copy the whole structure. This way there's
no need to modify the function every time we add a new field to the struct.
Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 there's a warning:
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'new' not described in 'ath10k_wow_convert_8023_to_80211'
drivers/net/wireless/ath/ath10k/wow.c:93: warning: Function parameter or member 'old' not described in 'ath10k_wow_convert_8023_to_80211'
Fix it by changing the documentation marker '/**' to a normal code comment.
While at it, clean up the line wrapping.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
With W=1 GCC warns:
drivers/net/wireless/ath/ath10k/htt.h:1746:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_32' is less than 4 [-Wpacked-not-aligned]
drivers/net/wireless/ath/ath10k/htt.h:1753:1: warning: alignment 1 of 'struct ath10k_htt_txbuf_64' is less than 4 [-Wpacked-not-aligned]
Fix that by using __align(4). Compile tested only.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When adding a new value to enum wmi_service it's very easy to miss that the new
value should be also added to wmi_service_name() mapping function. Modify the
function so that GCC can now warn about this:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_FOO' not handled in switch [-Wswitch]
And also add a reminder to the enum.
Thanks to Jouni Malinen for the idea.
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After implementing the next patch GCC reported:
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BTCOEX' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_MGMT_TX_WMI' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_SPOOF_MAC_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_VDEV_DISABLE_4_ADDR_SRC_LRN_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT' not handled in switch [-Wswitch]
drivers/net/wireless/ath/ath10k/wmi.h:385:2: warning: enumeration value 'WMI_SERVICE_THERM_THROT' not handled in switch [-Wswitch]
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
If supported, update transmit airtime in mac80211 with the airtime
values reported by the firmware. TX airtime of the PPDU is reported
via HTT data TX completion indication message.
A new service flag 'WMI_SERVICE_REPORT_AIRTIME' is added to advertise
the firmware support. For firmwares which do not support this feature,
TX airtime is calculated in the driver using TX bitrate.
Hardwares tested : QCA9984
Firmwares tested : 10.4-3.6.1-00841
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Multicast/broadcast traffic destined for a particular vlan group will
always be encrypted in software. To enable dynamic VLANs, it requires
driver support for sending software encrypted packets.
In ath10k, sending software encrypted frames is allowed only when we insmod
the driver with cryptmode param set to 1, this configuration disables
hardware crypto and enables RAW mode implicitly. Since, enabling raw
mode has performance impact, this cannot be considered as an ideal
solution for supporting VLANs in the driver.
As an alternative take, in this approach, cryptographic keys for
unicast traffic (per peer PTKs) and keys for non-vlan group traffic
will be configured in hardware, allowing hardware encryption for unicast
and non-vlan group traffic. Only vlan group traffic will be encrypted in
software and pushed to the target with encap mode set to RAW in the TX
descriptors.
Not all firmwares can support this type of key configuration(having few
keys installed in hardware and few only in software); for this purpose a
new WMI service flag "WMI_SERVICE_PER_PACKET_SW_ENCRYPT" is introduced to
advertise this support.
Also, adding the logic required to send sw encrypted frames in raw mode.
Hardwares Tested : QCA9984, QCA988X
Firmwares Tested : 10.4-3.5.3-00057, 10.2.4-1.0-00042
Signed-off-by: Manikanta Pubbisetty <mpubbise@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Configure fine timing measurement (FTM) responder role from the
ftm_responder bss param sent by mac80211. With FTM functionality offloaded
to firmware, adding the interface allows userspace to enable or disable
FTM responder functionality. ath10k disables it at the time of interface
creation.
Supported FW: 10.4
Tested on IPQ4019 with firmware: 10.4-3.2.1.1-00022
Signed-off-by: Pradeep Kumar Chitrapu <pradeepc@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The airtime of a transmitted frame will be estimated from last used tx rate
which the firmware reports with the peer stats feature
(WMI_SERVICE_PEER_STATS). The airtime is computed on the tx path and it
will be reported to mac80211 upon tx completion.
This change is based on Kan's orginal commit in Chromium tree
("CHROMIUM: ath10k: Implementing airtime fairness based TX scheduler")
ref: https://chromium-review.googlesource.com/588190
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Signed-off-by: Kan Yan <kyan@google.com>
[rmanohar@codeaurora.org: ported only the airtime computation]
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
[toke@redhat.com: Rebase to mac80211-next, add test note]
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
ath10k maintains common txqs list for all stations. This txq
management can be removed by migrating to mac80211 txq APIs
and let mac80211 handle txqs reordering based on reported airtime.
By doing this, txq fairness maintained in ath10k i.e processing
N frames per txq is removed. By adapting to mac80211 APIs,
ath10k will support mac80211 based airtime fairness algorithm.
Tested on QCA4019 with firmware version 10.4-3.2.1.1-00015
Tested on QCA9984 with firmware version 10.4-3.9.0.1-00005
Tested-by: Venkateswara Naralasetty <vnaralas@codeaurora.org>
Co-developed-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Rajkumar Manoharan <rmanohar@codeaurora.org>
Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Commit 750afb08ca ("cross-tree: phase out dma_zalloc_coherent()") introduced
a new checkpatch warning:
drivers/net/wireless/ath/ath10k/ce.c:1602: line over 90 characters
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports shadow registers write operation support
for copy engine for regular operation in powersave mode.
Since WCN3990 is a 64-bit target, the shadow register
implementation needs to be done in the copy engine handlers
for 64-bit target. Currently the shadow register implementation
is present in the 32-bit target handlers of copy engine.
Fix the shadow register copy engine write operation
implementation for 64-bit target(WCN3990).
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: b7ba83f7c4 ("ath10k: add support for shadow register for WNC3990")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The support to put WCN3990 firmware into Factory
test mode is not present currently. The WCN3990
firmware can operate in Factory test mode based
on the mode it receives in the wlan enable message
from the host driver.
When the host driver is started in testmode send
the operating mode as UTF mode, to the WCN3990
firmware, in the wlan enable message to start the
firmware in Factory test mode.
Tested on: WCN3990
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The DIAG copy engine is only used via polling, but it holds a spinlock
with softirqs disabled. Each iteration of our read/write loops can
theoretically take 20ms (two 10ms timeout loops), and this loop can be
run an unbounded number of times while holding the spinlock -- dependent
on the request size given by the caller.
As of commit 39501ea641 ("ath10k: download firmware via diag Copy
Engine for QCA6174 and QCA9377."), we transfer large chunks of firmware
memory using this mechanism. With large enough firmware segments, this
becomes an exceedingly long period for disabling soft IRQs. For example,
with a 500KiB firmware segment, in testing QCA6174A, I see 200 loop
iterations of about 50-100us each, which can total about 10-20ms.
In reality, we don't really need to block softirqs for this duration.
The DIAG CE is only used in polling mode, and we only need to hold
ce_lock to make sure any CE bookkeeping is done without screwing up
another CE. Otherwise, we only need to ensure exclusion between
ath10k_pci_diag_{read,write}_mem() contexts.
This patch moves to use fine-grained locking for the shared ce_lock,
while adding a new mutex just to ensure mutual exclusion of diag
read/write operations.
Tested on QCA6174A, firmware version WLAN.RM.4.4.1-00132-QCARMSWPZ-1.
Fixes: 39501ea641 ("ath10k: download firmware via diag Copy Engine for QCA6174 and QCA9377.")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
FW credit flow control is enabled for only WMI ctrl
service(CE3) but credit update is requested unconditionally
on all HTC services as part of HTC tx in CE3/CE0/CE4.
This is causing WOW failure as FW is not expecting credit
report request on other end-points(CE0/CE4).
Request credit report only on those endpoints where
credit flow control is enabled.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
wow pause iface config controls the PCI D0/D3-WOW cases for pcie
bus state. Firmware does not expects WOW_IFACE_PAUSE_ENABLED config
for bus/link that cannot be suspended ex:snoc and does not trigger
common subsystem shutdown.
Disable interface pause wow config for integrated chipset(WCN3990)
for correct WOW configuration in the firmware.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Register snoc bus layer suspend/resume PM ops and configure
the wakeup source(CE2) for the device.
Testing:
Tested on WCN3990 HW.
Tested FW: WLAN.HL.2.0-01192-QCAHLSWMTPLZ-1.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Many integrated QCA9984 WiFis in various IPQ806x platform routers
from various vendors (Netgear R7800, ZyXEL NBG6817, TP-LINK C2600,
etc.) have either blank, bogus or non-unique MAC-addresses in
their calibration data.
As a result, OpenWrt utilizes a discouraged binary calibration data
patching method that allows to modify the device's MAC-addresses right
at the source. This is because the ath10k' firmware extracts the MAC
address from the supplied radio/calibration data and issues a response
to the ath10k linux driver. Which was designed to take the main MAC in
ath10k_wmi_event_ready().
Part of the "setting an alternate MAC" issue was already tackled by a
patch from Brian Norris:
commit 9d5804662c
("ath10k: retrieve MAC address from system firmware if provided")
by allowing the option to specify an alternate MAC-address with the
established device_get_mac_address() function which extracts the right
address from DeviceTree/fwnode mac-address or local-mac-address
properties and saves it for later.
However, Ben Greear noted that the Qualcomm's ath10k firmware is liable
to not properly calculate its rx-bssid mask in this case. This can cause
issues in the popluar "multiple AP with a single ath10k instance"
configurations.
To improve MAC address handling, Felix Fietkau suggested to call
pdev_set_base_macaddr_cmdid before bringing up the first vif and
use the first vif MAC address there. Which is in ath10k_core_start().
This patch implement Felix Fietkau's request to
"call pdev_set_base_macaddr_cmdid before bringing up the first vif".
The pdev_set_base_macaddr_cmdid is already declared for all devices
and version. The driver just needed the support code for this
function.
Tested on:
QCA9880/CUS223, firmwares: 10.2.4.13-2, 10.2.4.70.44, 10.2.4-1.0-00041
QCA9887/MR33 firmware:10.2.4-1.0-00033
QCA4019/RT-AC58U firmware: 10.4-3.4-00104, 10.4-3.5.3-00057
QCA9984/R7800 firmware: Candela Technologies (CT) Firmware
BugLink: https://lists.openwrt.org/pipermail/openwrt-devel/2018-November/014595.html
Fixes: 9d5804662c ("ath10k: retrieve MAC address from system firmware if provided")
Cc: Brian Norris <briannorris@chromium.org>
Cc: Ben Greear <greearb@candelatech.com>
Cc: Felix Fietkau <nbd@nbd.name>
Cc: Mathias Kresin <dev@kresin.me>
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
TLV based firmware ex. QCA6174, WCN3990 expects key cipher value
set to 9 while non-TLV firmware expects key cipher value set to 8
for enabling GCMP and GCMP-256 cipher suites.
To fix this problem, attach the key cipher suite values based on
wmi version.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Hostapd uses CCMP, GCMP & GCMP-256 as 'wpa_pairwise' option to run WPA3.
In WCN3990 firmware cipher suite numbers 9 to 11 are for CCMP,
GCMP & GCMP-256.
To enable CCMP, GCMP & GCMP-256 cipher suites in WCN3990 firmware,
host sets 'n_cipher_suites = 11' while initializing hardware parameters.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Abhishek Ambure <aambure@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The series "[PATCH 0/2] mt76x0: initialize per-channel max_power" depends on
commit d04ca38386 ("mt76x0u: fix suspend/resume"), so merge wireless-drivers
into wireless-drivers-next to get that.
ath.git patches for 5.1. Major changes:
ath10k
* change QMI interface to support the new (and backwards incompatible)
interface from HL3.1 and used in recent HL2.0 branch firmware releases
ath
* add new country codes for US
Firmware sends the tx_duration for each in HTT_T2H_MSG_TYPE_PEER_STATS
msg. Fill the tx_duration sent by firmware in the tx stats information
per STA.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The firmware advertises the LDPC support information for HT in
HT capability info in the wmi service ready event. To provide
granularity, firmware now advertises WMI_HT_CAP_RX_LDPC and
WMI_HT_CAP_TX_LDPC separately. To support LDPC, host should
also check for WMI_HT_CAP_RX_LDPC and WMI_HT_CAP_TX_LDPC in HT
capabilities.
Add a condition to existing logic in host to know whether firmware
supports LDPC or not.
Tested HW: WCN3990
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Surabhi Vishnoi <svishnoi@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Reduce the transmit MSDU count for SDIO, to match with the descriptors
as used by the firmware. This also acts as a high watermark level for
transmit. Too many packets to the firmware results in transmit overflow
interrupt.
It only affect SDIO chip, it will not cause functionaly changes to
other hardware.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Alagu Sankar <alagusankar@silex-india.com>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
When calling debugfs functions, they can now return error values if
something went wrong. If that happens, return a NULL as a *dentry to
the relay core instead of passing it an illegal pointer.
The relay core should be able to handle an illegal pointer, but add this
check to be safe.
Cc: Kalle Valo <kvalo@codeaurora.org>
Cc: ath10k@lists.infradead.org
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/wireless/ath/ath10k/snoc.c: In function 'ath10k_snoc_tx_pipe_cleanup':
drivers/net/wireless/ath/ath10k/snoc.c:681:22: warning:
variable 'ar_snoc' set but not used [-Wunused-but-set-variable]
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
sdio_register_driver() doesn't do this for us, unlike (for example)
platform_driver_register(). This is important for helping track
module-to-device relationships.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The swap box flag of firmware is not set before htc ready, then it
will not set swap box flag in ath10k driver, and it will let swap
box setting not same between firmware and ath10k driver, then it
will trigger firmware assert failure.
Check the flag and set swap box after htc ready will fix the firmware
assert failure.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00005-QCARMSWP-1.
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The hw-restart crash inject mode is a special mode, where
there is no crash generated in the firmware, but instead
the driver restarts the firmware. In order to restart WCN3990
firmware, the driver needs to send qmi_wlan_disable message
followed by the qmi_wlan_enable message to the WCN3990 firmware.
Currently the qmi_wlan_disable message is not sent to
the WCN3990 firmware when hw-restart crash is injected,
which causes the firmware to crash when the driver sends
qmi_wlan_enable message during ath10k_restart.
Send qmi_wlan_disable to the WCN3990 firmware when the
hw-restart crash is injected via debugfs.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
The management frames transmitted are dma mapped with
direction TO_DEVICE, but incorrectly mapped with
direction FROM_DEVICE during tx complete and error cases.
Fix the direction of dma during dma unmap of the
transmitted management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Fixes: 38a1390e02 ("ath10k: dma unmap mgmt tx buffer if wmi cmd send fails")
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 sends tx completion of multiple management
frames bundled together in a single event, if the
host driver exposes the support to handle this
bundled tx completion event. This reduces the number
of WMI events which are sent to the host driver by
the target.
Set the BUNDLE_TX_COMPL flag in the host capability
flags when host sends the wmi init command, to indicate
the host capability to handle bundled tx completion for
management frames.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 supports sending tx completion for multiple
management frames bundled together in a single event.
Add support to handle the bundled tx completion
event for WCN3990.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
HOST capability interface data structures are updated
in HL3.1 fw version. Update the qmi host capability
members for compatibility across different firmware
versions.
Since this change breaks backward compatibility with
HL2.0 fw, HL2.0 fw upgrade to WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
or later version is required.
Testing:
Tested on QCS404 platform(WCN3990 HW).
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1,
WLAN.HL.2.0-01617-QCAHLSWMTPLZ-1
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcWoRZAAoJEG4XJFUm622bOm4H/j2Tt6qS5yz3ioH2I7R+f7e/
8C2JJia+uQs8iChdyCjCFcDymmjB2l5u72JvupwCdERzp3okv/xmJiLW5wFW2z4x
B3Nrd4FV2EMIdsRXg1RWbwZHC4wIY6lFhL1OcUcuNwpb5ab1ppvQFHmH5logd7DC
euFSe02g8xmXdUMciRDKGUdiSiDIApmx9dUfguaqYtepqeW3hmDEEkeDicaf2fjq
cM5qAvssIAgUTqwIImEQQEU7j7A2TgMYkRBNzwv2QG47jy6OlgXkZVByvtq59irg
v4BFNtG6uRWTugxQ/FwYWeqsrnjegFNKm5MFbS6BDxbe05M7QzeK8zm55fE9ZGk=
=cHbd
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-02-06' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
First set of patches for 5.1. Lots of new features in various drivers
but nothing really special standing out.
Major changes:
brcmfmac
* DMI nvram filename quirk for PoV TAB-P1006W-232 tablet
rsi
* support for hardware scan offload
iwlwifi
* support for Target Wakeup Time (TWT) -- a feature that allows the AP
to specify when individual stations can access the medium
* support for mac80211 AMSDU handling
* some new PCI IDs
* relicense the pcie submodule to dual GPL/BSD
* reworked the TOF/CSI (channel estimation matrix) implementation
* Some product name updates in the human-readable strings
mt76
* energy detect regulatory compliance fixes
* preparation for MT7603 support
* channel switch announcement support
mwifiex
* support for sd8977 chipset
qtnfmac
* support for 4addr mode
* convert to SPDX license identifiers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
HTT aggr message parameter in HL2.0 fw are different in comparison
to legacy fw version. Fill correct HTT aggr msg parameter for
targets using HL2.0 firmware.
Signed-off-by: Govind Singh <govinds@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
After system entering S5 (shut down but system still
providing power to QCA9377) on Ubuntu platform, power
consumption of QCA9377 is 69mA, which is too high.
The root cause is pci_soft_reset is not set for QCA9377
during pci probe.
To fix this issue, set 'pci_soft_reset' to 'th10k_pci_warm_reset',
and then the power consumption drops to a normal value(10mA).
Verified on Dell Ubuntu platform with firmware:
WLAN.TF.1.0-00002-QCATFSWPZ-5
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Yu Wang <yyuwang@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is a 37-bit target but can address memory range
only upto 35 bits. The 36th bit is used to control the
smmu/iommu translation and the 37th bit is used by the
internal bus masters to access the wifi subsystem internal
SRAM. With the DMA mask set to 37i-bit, the host driver
can get 37-bit dma address, which leads to incorrect
address access in the target.
Hence the host driver can used addresses upto 35-bit
for WCN3990. Fix the dma mask for wcn3990 to 35-bit,
instead of 37-bit.
Tested HW: WCN3990
Tested FW: WLAN.HL.2.0-01188-QCAHLSWMTPLZ-1
Tested-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
WCN3990 is SNOC, not PCI. This prevents probing WCN3990.
Fixes: 367c899f62 ("ath10k: add bus type check in ath10k_init_hw_params")
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
We already need to zero out memory for dma_alloc_coherent(), as such
using dma_zalloc_coherent() is superflous. Phase it out.
This change was generated with the following Coccinelle SmPL patch:
@ replace_dma_zalloc_coherent @
expression dev, size, data, handle, flags;
@@
-dma_zalloc_coherent(dev, size, handle, flags)
+dma_alloc_coherent(dev, size, handle, flags)
Suggested-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Luis Chamberlain <mcgrof@kernel.org>
[hch: re-ran the script on the latest tree]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJcG9TEAAoJEG4XJFUm622byW8H/1vMVJhXwgIZbHeoUKNa47Yp
Z7Jv5vW8IGXu+lp7DyoedDCbq4+lskNSlDV1DmysNChLgDnApU/3oCd/jH8EiGPV
JAFUHb85HuVLTTpPpNHtnYz3IzL7r098TNVxOU0VD+xILM0Mf0aCeXztgmFWpGaY
/rfHkId8oKUezIjdu6Dc96mqITrT6WRNtnOMfjr6dZPjClRTS44Hyz3Ga3rXABBL
/n8BCkl0GpKGrL3mBy2CCR5mVY8zfxMB4Aj2zx7bccZ8i2i2QjrGlXCHyB6ImNrR
lv4L1fUVXZWVdeOe8EbpftY7zEsPrX+XNm6h1kckdB7UyuBROpQLsVb+yxlLh9g=
=mhAw
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2018-12-20' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.21
Last set of patches for 4.21. mt76 is still in very active development
and having some refactoring as well as new features. But also other
drivers got few new features and fixes.
Major changes:
ath10k
* add amsdu support for QCA6174 monitor mode
* report tx rate using the new ieee80211_tx_rate_update() API
* wcn3990 support is not experimental anymore
iwlwifi
* support for FW version 43 for 9000 and 22000 series
brcmfmac
* add support for CYW43012 SDIO chipset
* add the raw 4354 PCIe device ID for unprogrammed Cypress boards
mwifiex
* add NL80211_STA_INFO_RX_BITRATE support
mt76
* use the same firmware for mt76x2e and mt76x2u
* mt76x0e survey support
* more unification between mt76x2 and mt76x0
* mt76x0e AP mode support
* mt76x0e DFS support
* rework and fix tx status handling for mt76x0 and mt76x2
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Lots of conflicts, by happily all cases of overlapping
changes, parallel adds, things of that nature.
Thanks to Stephen Rothwell, Saeed Mahameed, and others
for their guidance in these resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add wmi configuration cmd to configure base band(BB) power amplifier(PA)
off timing values in hardware. The default PA off timings were fine tuned
to make proper DFS radar detection in QCA reference design. If ODM uses
different PA in their design, then the same default PA off timing values
cannot be used, it requires different settling time to detect radar pulses
very sooner and avoid radar detection problems. In that case it provides
provision to select proper PA off timing values based on the PA hardware used.
The PA component is part of FEM hardware and new device tree entry
"ext-fem-name" is used to indentify the FEM hardware. And this wmi configuration
cmd is enabled via wmi service flag "WMI_SERVICE_BB_TIMING_CONFIG_SUPPORT".
Other way is to apply these values through calibration data, but recalibration
of all boards out there might not be feasible.
This change tested on firmware ver 10.2.4-1.0-00042 in QCA988X chipset.
Signed-off-by: Bhagavathi Perumal S <bperumal@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Wen Gong