This code has been untouched since it was merged many years ago, and has
severely bitrotted since, suggesting that the board has no real users
left. Notice of intent to remove has been sent out over the last few
years, with no takers. Kill it off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sdk7786 FPGA supports a number of user settable input switches that
are otherwise unused. This wires up a dummy gpio chip for the switch bank
to simply expose them to userspace.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the sh7757lcr board.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch series adds support for ITO Co., Ltd.'s SH-2007 reference
platform (A PC-104 based SH7780 platform).
This is a direct port of the out-of-tree board support from the vendor's
kernel, originally located at:
http://ms-n.org/sh-linux/kernel/
More information on the board and the vendor can be obtained from the
vendor's site at:
http://www.itonet.co.jp/
Presently supported peripherals are CF and ethernet, with support for
the on-board IDE still pending further testing.
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Reviewed-by: Magnus Damm <magnus.damm@gmail.com>
Signed-off-by: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
urquell only provides PIO in the PCI case, while the x3proto board never
had a working PCIe controller, so it can simply disable it outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was only built in for Urquell boards, but the same
approach can be used on SDK7786 now that the mode pin reading is
supported, so make it generic to SH7786.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This stubs in some preliminary board support for the RTE SDK7786.
This is quite stunted at the moment, and primarily builds on top of the
system FPGA. FPGA IRQs are handled via CPU IRL masking for simplicity,
with initial peripheral support restricted to the debug ethernet.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This board doesn't use trapped I/O for anything, so just kill off the
select. This was causing problems in the unhandled page fault die path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the EcoVec board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic kfr2r09 board support. Only
the SCIF1 console is supported with this patch, but
this patch and a proper sh7724 configuration is all
that is needed. Combine with an initramfs to have a
small RAM based kernel and distribution booted as
zImage from RAM via JTAG.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds initial support for the PCI-Express module in the SH7786,
particularly as it relates to the urquell platform. Presently it is
only supported in root complex mode, with endpoint mode still requiring
more debugging. 29/32-bit mode and lane configurations are selectable via
board mode pins, and are otherwise fixed.
Only 4x and 1x PCI channels are presently handled, the PCI bridge still
requires additional debugging and stabilization in hardware.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the ms7724se solution engine board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All 32-bit SuperH processors currently go through __ioremap_mode()
and check for IO_TRAPPED and directly mapped segments. With this
patch we simplify the MMU less case with a pass through version of
__ioremap_mode() which just returns the physical address.
The effects of this is change are:
- fix non-MMU ioremap() of high address hardware blocks (sh7203 CMT)
- make sure IO_TRAPPED is not selected
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Polaris is an SMSC reference platform with a SH7709S CPU and LAN9118
ethernet controller. This patch adds support for it.
Updated following feedback from Nobuhiro Iwamatsu.
Signed-off-by: Steve Glendinning <steve.glendinning@smsc.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the ESPT-Giga (Ethernet Serial Parallel
Translator) SH7763-based reference board.
Board support is relatively sparse, presently supporting serial,
gigabit ethernet, USB host, and MTD.
More information (in Japanese) available at:
http://www.cente.jp/product/cente_hard/ESPT-Giga.html
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a new defconfig for SH7785LCR in 32-bit mode, and update the power
off code to avoid 29-bit assumptions.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the SH7786-based Urquell board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix up the build for mach-highlander and mach-rsk. These operated on the
assumption that GENERIC_GPIO support with an optional GPIOLIB was
possible. This used to be true, but has not been the case since commit-id
d56cc8bc661ac1ceded8d45ba2d53bb134fee17d ("sh: use gpiolib"), where the
GENERIC_GPIO implementation was rewritten to use GPIOLIB directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the SuperH gpio code to make use of gpiolib. The
gpiolib callbacks get() and set() are lockless, but we use our own
spinlock for the other operations to make sure hardware register
bitfield accesses stay atomic.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
RSK+ platforms have quite a few characteristics in common, so roll them
together in to a shiny new RSK mach-type.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the RTE RSK+ 7201 board.
Signed-off-by: Peter Griffin <pgriffin@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch hooks up the magicpanelr2 board with the sh7720 pinmux code.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make the rsk7203 board use the newly added sh7203 pinmux code.
Only a single LED plus the serial console pins for now.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on AP325RXA and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
While at it 2 LEDs and one switch are added and exported to user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the GPIO code on Migo-R and converts the code from
register based pinmux configuration to GPIO based pin by pin setup.
Fix whitespace damage while at it and add 2 LEDs and export them to
user space.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the Renesas (RTE) EDOSK7760 board. Currently
supported devices are:
- ramdisk support
- ethernet support
- nfs support
- ext2/ext3 support
- i2c support
- fb support (M)
Signed-off-by: Luca Santini <luca.santini@spesonline.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt