USB4 added a capability to tunnel USB 3.x protocol over the USB4
fabric. USB4 device routers may include integrated SuperSpeed HUB or a
function or both. USB tunneling follows PCIe so that the tunnel is
created between the parent and the child router from USB3 downstream
adapter port to USB3 upstream adapter port over a single USB4 link.
This adds support for USB 3.x tunneling and also capability to discover
existing USB 3.x tunnels (for example created by connection manager in
boot firmware).
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Co-developed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Link: https://lore.kernel.org/r/20191217123345.31850-9-mika.westerberg@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Titan Ridge supports Display Port 1.4 which adds HBR3 (High Bit Rate)
rates that may be up to 8.1 Gb/s over 4 lanes. This translates to
effective data bandwidth of 25.92 Gb/s (as 8/10 encoding is removed by
the DP adapters when going over Thunderbolt fabric). If another high
rate monitor is connected we may need to reduce the bandwidth it
consumes so that it fits into the total 40 Gb/s available on the
Thunderbolt fabric.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In addition to PCIe and Display Port tunnels it is also possible to
create tunnels that forward DMA traffic from the host interface adapter
(NHI) to a NULL port that is connected to another domain through a
Thunderbolt cable. These tunnels can be used to carry software messages
such as networking packets.
To support this we introduce another tunnel type (TB_TUNNEL_DMA) that
supports paths from NHI to NULL port and back.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Display Port tunnels are somewhat more complex than PCIe tunnels as it
requires 3 tunnels (AUX Rx/Tx and Video). In addition we are not
supposed to create the tunnels immediately when a DP OUT is enumerated.
Instead we need to wait until we get hotplug event to that adapter port
or check if the port has HPD set before tunnels can be established. This
adds Display Port tunneling support to the software connection manager.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In Apple Macs the boot firmware (EFI) connects all devices automatically
when the system is started, before it hands over to the OS. Instead of
ignoring we discover all those PCIe tunnels and record them using our
internal structures, just like we do when a device is connected after
the OS is already up.
By doing this we can properly tear down tunnels when devices are
disconnected. Also this allows us to resume the existing tunnels after
system suspend/resume cycle.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
To be able to tunnel non-PCIe traffic, separate tunnel functionality
into generic and PCIe specific parts. Rename struct tb_pci_tunnel to
tb_tunnel, and make it hold an array of paths instead of just two.
Update all the tunneling functions to take this structure as parameter.
We also move tb_pci_port_active() to switch.c (and rename it) where we
will be keeping all port and switch related functions.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
In order to tunnel non-PCIe traffic as well rename tunnel_pci.[ch] to
tunnel.[ch] to reflect this fact. No functional changes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Rajmohan Mani