DSL and CM (Cable Modem) support 8 B max transfer size and have a custom
DT binding for that reason. This driver was checking for a wrong
"compatible" however which resulted in an incorrect setup.
Fixes: e2e5a2c618 ("i2c: brcmstb: Adding support for CM and DSL SoCs")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Driver builds fine with COMPILE_TEST. Enable it for wider test coverage
and easier maintenance.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Michal Simek <michal.simek@xilinx.com>
There is a minor chance for a race, if a pointer to an i2c-bus subnode
is stored and then reused after releasing its reference, and it would
be sufficient to get one more reference under a loop over children
subnodes.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
If i2c_add_adapter() fails to add an I2C adapter found on QCOM CCI
controller, on error path i2c_del_adapter() is still called.
Fortunately there is a sanity check in the I2C core, so the only
visible implication is a printed debug level message:
i2c-core: attempting to delete unregistered adapter [Qualcomm-CCI]
Nevertheless it would be reasonable to correct the probe error path.
Fixes: e517526195 ("i2c: Add Qualcomm CCI I2C driver")
Signed-off-by: Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The CLKT register contains at poweron 0x40, which at our typical 100kHz
bus rate means .64ms. But there is no specified limit to how long devices
should be able to stretch the clocks, so just disable the timeout. We
still have a timeout wrapping the entire transfer.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
BugLink: https://github.com/raspberrypi/linux/issues/3064
Signed-off-by: Wolfram Sang <wsa@kernel.org>
partial support for < MAX_ORDER - 1 granularity for virtio-mem
driver_override for vdpa
sysfs ABI documentation for vdpa
multiqueue config support for mlx5 vdpa
Misc fixes, cleanups.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQFDBAABCAAtFiEEXQn9CHHI+FuUyooNKB8NuNKNVGkFAmHiDHkPHG1zdEByZWRo
YXQuY29tAAoJECgfDbjSjVRpVT4H/3Veixt3uYPOmuLU2tSx+8X+sFTtik81hyiE
okz5fRJrxxA8SqS76FnmO10FS4hlPOGNk0Z5WVhr0yihwFvPLvpCM/xi2Lmrz9I7
pB0sXOIocEL1xApsxukR9K1Twpb2hfYsflbJYUVlRfhS5G0izKJNZp5I7OPrzd80
vVNNDWKW2iLDlfqsavumI4Kvm4nsFuCHG03jzMtcIa7YTXYV3DORD4ZGFFVUOIQN
t5F74TznwHOeYgJeg7TzjFjfPWmXjLetvx10QX1A1uOvwppWW/QY6My0UafTXNXj
VB3gOwJPf+gxXAXl/4bafq4NzM0xys6cpcPpjvhmU+erY4UuyAU=
=Y1eO
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio updates from Michael Tsirkin:
"virtio,vdpa,qemu_fw_cfg: features, cleanups, and fixes.
- partial support for < MAX_ORDER - 1 granularity for virtio-mem
- driver_override for vdpa
- sysfs ABI documentation for vdpa
- multiqueue config support for mlx5 vdpa
- and misc fixes, cleanups"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost: (42 commits)
vdpa/mlx5: Fix tracking of current number of VQs
vdpa/mlx5: Fix is_index_valid() to refer to features
vdpa: Protect vdpa reset with cf_mutex
vdpa: Avoid taking cf_mutex lock on get status
vdpa/vdpa_sim_net: Report max device capabilities
vdpa: Use BIT_ULL for bit operations
vdpa/vdpa_sim: Configure max supported virtqueues
vdpa/mlx5: Report max device capabilities
vdpa: Support reporting max device capabilities
vdpa/mlx5: Restore cur_num_vqs in case of failure in change_num_qps()
vdpa: Add support for returning device configuration information
vdpa/mlx5: Support configuring max data virtqueue
vdpa/mlx5: Fix config_attr_mask assignment
vdpa: Allow to configure max data virtqueues
vdpa: Read device configuration only if FEATURES_OK
vdpa: Sync calls set/get config/status with cf_mutex
vdpa/mlx5: Distribute RX virtqueues in RQT object
vdpa: Provide interface to read driver features
vdpa: clean up get_config_size ret value handling
virtio_ring: mark ring unused on error
...
This will enable cleanups down the road.
The idea is to disable cbs, then add "flush_queued_cbs" callback
as a parameter, this way drivers can flush any work
queued after callbacks have been disabled.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Link: https://lore.kernel.org/r/20211013105226.20225-1-mst@redhat.com
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Pull i2c updates from Wolfram Sang:
"Mostly driver updates and refactorization.
The removal of the XLR driver and the i801 refactoring stand out a
little. In the core, we enabled async suspend/resume for I2C
controllers and their clients. No issues were reported during the test
phase in -next. We will see how this goes for mainline"
* 'i2c/for-mergewindow' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (54 commits)
i2c: sh_mobile: remove unneeded semicolon
i2c: riic: Use platform_get_irq() to get the interrupt
i2c: sh_mobile: Use platform_get_irq_optional() to get the interrupt
i2c: bcm2835: Use platform_get_irq() to get the interrupt
i2c: aspeed: Remove unused includes
dt-bindings: i2c: aspeed: Drop stray '#interrupt-cells'
i2c: sh_mobile: update to new DMAENGINE API when terminating
i2c: rcar: update to new DMAENGINE API when terminating
i2c: exynos5: Fix getting the optional clock
i2c: designware-pci: Convert to use dev_err_probe()
i2c: designware-pci: use __maybe_unused for PM functions
i2c: designware-pci: Group MODULE_*() macros
i2c: designware-pci: Add a note about struct dw_scl_sda_cfg usage
i2c: designware-pci: Fix to change data types of hcnt and lcnt parameters
i2c: designware: Do not complete i2c read without RX_FULL interrupt
eeprom: at24: Add support for 24c1025 EEPROM
dt-bindings: at24: add at24c1025
i2c: tegra: use i2c_timings for bus clock freq
dt-bindings: at24: Rework special case compatible handling
i2c: i801: Don't clear status flags twice in interrupt mode
...
Eliminate the following coccicheck warning:
./drivers/i2c/busses/i2c-sh_mobile.c:849:3-4: Unneeded semicolon
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
- Update ACPICA code in the kernel to the 20211217 upstream release
including the following changes:
* iASL/Disassembler: Additional support for NHLT table (Bob Moore).
* Change a return_ACPI_STATUS (AE_BAD_PARAMETER) (Bob Moore).
* Fix a couple of warnings under MSVC (Bob Moore).
* iASL: Add TDEL table to both compiler/disassembler (Bob Moore).
* iASL/NHLT table: "Specific Data" field support (Bob Moore).
* Use original data_table_region pointer for accesses (Jessica
Clarke).
* Use original pointer for virtual origin tables (Jessica Clarke).
* Macros: Remove ACPI_PHYSADDR_TO_PTR (Jessica Clarke).
* Avoid subobject buffer overflow when validating RSDP signature
(Jessica Clarke).
* iASL: Add suppport for AGDI table (Ilkka Koskinen).
* Hardware: Do not flush CPU cache when entering S4 and S5 (Kirill
A. Shutemov).
* Expand the ACPI_ACCESS_ definitions (Mark Langsdorf).
* Utilities: Avoid deleting the same object twice in a row (Rafael
Wysocki).
* Executer: Fix REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
(Rafael Wysocki).
* Fix AEST Processor generic resource substructure data field byte
length (Shuuichirou Ishii).
* Fix wrong interpretation of PCC address (Sudeep Holla).
* Add support for PCC Opregion special context data (Sudeep Holla).
- Implement OperationRegion handler for PCC Type 3 subtype (Sudeep
Holla).
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system
PM transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang Li).
- Rework flushing of EC work while suspended to idle and clean up
the handling of events in the ACPI EC driver (Rafael Wysocki).
- Prohibit ec_sys module parameter write_support from being used
when the system is locked down (Hans de Goede).
- Make the ACPI processor thermal driver use cpufreq_cpu_get() to
check for presence of cpufreq policy (Manfred Spraul).
- Avoid unnecessary CPU cache flushing in the ACPI processor idle
driver (Kirill A. Shutemov).
- Replace kernel.h with the necessary inclusions in the ACPI
processor driver (Andy Shevchenko).
- Use swap() instead of open coding it in the ACPI processor idle
driver (Guo Zhengkui).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
- Add AEST to the list of known ACPI table signatures (Shuuichirou
Ishii).
- Make ACPI NUMA code take hotpluggable memblocks into account when
CONFIG_MEMORY_HOTPLUG is not set (Vitaly Kuznetsov).
- Use default_groups in kobj_type in the ACPI sysfs code (Greg
Kroah-Hartman).
- Rearrange _CPC structure documentation (Andy Shevchenko).
- Drop an always true check from the ACPI thermal driver (Adam
Borowski).
- Add new "not charging" quirk for Lenovo ThinkPads to the ACPI
battery driver (Thomas Weißschuh).
-----BEGIN PGP SIGNATURE-----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=IGwJ
-----END PGP SIGNATURE-----
Merge tag 'acpi-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI updates from Rafael Wysocki:
"These are usual ACPICA code updates (although there are more of them
than in the last few releases), a noticeable EC driver update (which
mostly consists of cleanups, though), the device enumeration quirks
handling rework from Hans, some updates eliminating unnecessary CPU
cache flushing in some places (processor idle and system-wide PM code)
and a bunch of assorted cleanups and fixes.
Specifics:
- Update ACPICA code in the kernel to the 20211217 upstream release
including the following changes:
- iASL/Disassembler: Additional support for NHLT table (Bob
Moore).
- Change a return_ACPI_STATUS (AE_BAD_PARAMETER) (Bob Moore).
- Fix a couple of warnings under MSVC (Bob Moore).
- iASL: Add TDEL table to both compiler/disassembler (Bob Moore).
- iASL/NHLT table: "Specific Data" field support (Bob Moore).
- Use original data_table_region pointer for accesses (Jessica
Clarke).
- Use original pointer for virtual origin tables (Jessica Clarke).
- Macros: Remove ACPI_PHYSADDR_TO_PTR (Jessica Clarke).
- Avoid subobject buffer overflow when validating RSDP signature
(Jessica Clarke).
- iASL: Add suppport for AGDI table (Ilkka Koskinen).
- Hardware: Do not flush CPU cache when entering S4 and S5 (Kirill
A. Shutemov).
- Expand the ACPI_ACCESS_ definitions (Mark Langsdorf).
- Utilities: Avoid deleting the same object twice in a row (Rafael
Wysocki).
- Executer: Fix REFCLASS_REFOF case in acpi_ex_opcode_1A_0T_1R()
(Rafael Wysocki).
- Fix AEST Processor generic resource substructure data field byte
length (Shuuichirou Ishii).
- Fix wrong interpretation of PCC address (Sudeep Holla).
- Add support for PCC Opregion special context data (Sudeep
Holla).
- Implement OperationRegion handler for PCC Type 3 subtype (Sudeep
Holla).
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system PM
transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang
Li).
- Rework flushing of EC work while suspended to idle and clean up the
handling of events in the ACPI EC driver (Rafael Wysocki).
- Prohibit ec_sys module parameter write_support from being used when
the system is locked down (Hans de Goede).
- Make the ACPI processor thermal driver use cpufreq_cpu_get() to
check for presence of cpufreq policy (Manfred Spraul).
- Avoid unnecessary CPU cache flushing in the ACPI processor idle
driver (Kirill A. Shutemov).
- Replace kernel.h with the necessary inclusions in the ACPI
processor driver (Andy Shevchenko).
- Use swap() instead of open coding it in the ACPI processor idle
driver (Guo Zhengkui).
- Fix the handling of defective LPAT in the ACPI xpower PMIC driver
and clean up some definitions of PMIC data structures (Hans de
Goede).
- Fix outdated comment in the ACPI DPTF driver (Sumeet Pawnikar).
- Add AEST to the list of known ACPI table signatures (Shuuichirou
Ishii).
- Make ACPI NUMA code take hotpluggable memblocks into account when
CONFIG_MEMORY_HOTPLUG is not set (Vitaly Kuznetsov).
- Use default_groups in kobj_type in the ACPI sysfs code (Greg
Kroah-Hartman).
- Rearrange _CPC structure documentation (Andy Shevchenko).
- Drop an always true check from the ACPI thermal driver (Adam
Borowski).
- Add new "not charging" quirk for Lenovo ThinkPads to the ACPI
battery driver (Thomas Weißschuh)"
* tag 'acpi-5.17-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (64 commits)
ACPI: PCC: Implement OperationRegion handler for the PCC Type 3 subtype
ACPI / x86: Skip AC and battery devices on x86 Android tablets with broken DSDTs
ACPI / x86: Introduce an acpi_quirk_skip_acpi_ac_and_battery() helper
ACPI: processor: thermal: avoid cpufreq_get_policy()
serdev: Do not instantiate serdevs on boards with known bogus DSDT entries
i2c: acpi: Do not instantiate I2C-clients on boards with known bogus DSDT entries
ACPI / x86: Add acpi_quirk_skip_[i2c_client|serdev]_enumeration() helpers
ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
PCI/ACPI: Fix acpi_pci_osc_control_set() kernel-doc comment
ACPI: battery: Add the ThinkPad "Not Charging" quirk
ACPI: sysfs: use default_groups in kobj_type
ACPICA: Update version to 20211217
ACPICA: iASL/NHLT table: "Specific Data" field support
ACPICA: iASL: Add suppport for AGDI table
ACPICA: iASL: Add TDEL table to both compiler/disassembler
ACPICA: Fixed a couple of warnings under MSVC
ACPICA: Change a return_ACPI_STATUS (AE_BAD_PARAMETER)
ACPICA: Hardware: Do not flush CPU cache when entering S4 and S5
ACPICA: Add support for PCC Opregion special context data
ACPICA: Fix wrong interpretation of PCC address
...
-----BEGIN PGP SIGNATURE-----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=cCwW
-----END PGP SIGNATURE-----
Merge tag 'media/v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New sensor driver: ov5693
- A new driver for STM32 Chrom-ART Accelerator
- Added V4L2 core helper functions for VP9 codec
- Hantro driver has gained support for VP9 codecs
- Added support for Maxim MAX96712 Quad GMSL2 Deserializer
- The staging atomisp driver has gained lots of improvements, fixes and
cleanups. It now works with userptr
- Lots of random driver improvements as usual
* tag 'media/v5.17-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (397 commits)
media: ipu3-cio2: Add support for instantiating i2c-clients for VCMs
media: ipu3-cio2: Call cio2_bridge_init() before anything else
media: ipu3-cio2: Defer probing until the PMIC is fully setup
media: hantro: Add support for Allwinner H6
media: dt-bindings: allwinner: document H6 Hantro G2 binding
media: hantro: Convert imx8m_vpu_g2_irq to helper
media: hantro: move postproc enablement for old cores
media: hantro: vp9: add support for legacy register set
media: hantro: vp9: use double buffering if needed
media: hantro: add support for reset lines
media: hantro: Fix probe func error path
media: i2c: hi846: use pm_runtime_force_suspend/resume for system suspend
media: i2c: hi846: check return value of regulator_bulk_disable()
media: hi556: Support device probe in non-zero ACPI D state
media: ov5675: Support device probe in non-zero ACPI D state
media: imx208: Support device probe in non-zero ACPI D state
media: ov2740: support device probe in non-zero ACPI D state
media: ov5670: Support device probe in non-zero ACPI D state
media: ov8856: support device probe in non-zero ACPI D state
media: ov8865: Disable only enabled regulators on error path
...
These are all minor bug fixes and cleanups to code in arch/arm and
arch/arm64 that is specific to one SoC, updating Kconfig symbols,
the MAINTAINERS file, and removing some dead code.
-----BEGIN PGP SIGNATURE-----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=8wnp
-----END PGP SIGNATURE-----
Merge tag 'soc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC updates from Arnd Bergmann:
"These are all minor bug fixes and cleanups to code in arch/arm and
arch/arm64 that is specific to one SoC, updating Kconfig symbols, the
MAINTAINERS file, and removing some dead code"
* tag 'soc-5.17' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
arm64: exynos: Enable Exynos Multi-Core Timer driver
ARM: ixp4xx: remove unused header file pata_ixp4xx_cf.h
ARM: ixp4xx: remove dead configs CPU_IXP43X and CPU_IXP46X
MAINTAINERS: Add Florian as BCM5301X and BCM53573 maintainer
ARM: samsung: Remove HAVE_S3C2410_I2C and use direct dependencies
ARM: imx: rename DEBUG_IMX21_IMX27_UART to DEBUG_IMX27_UART
ARM: imx: remove dead left-over from i.MX{27,31,35} removal
ARM: s3c: add one more "fallthrough" statement in Jive
ARM: s3c: include header for prototype of s3c2410_modify_misccr
ARM: shmobile: rcar-gen2: Add missing of_node_put()
Merge ACPI device enumeration updates, ACPI power management updates
and PCI host bridge ACPI driver updates for 5.17-rc1:
- Introduce acpi_fetch_acpi_dev() as a replacement for
acpi_bus_get_device() and use it in the ACPI subsystem (Rafael
Wysocki).
- Avoid using _CID for device enumaration if _HID is missing or
invalid (Rafael Wysocki).
- Rework quirk handling during ACPI device enumeration and add some
new quirks for known broken platforms (Hans de Goede).
- Avoid unnecessary or redundant CPU cache flushing during system
PM transitions (Kirill A. Shutemov).
- Add PM debug messages related to power resources (Rafael Wysocki).
- Fix kernel-doc comment in the PCI host bridge ACPI driver (Yang Li).
* acpi-scan:
serdev: Do not instantiate serdevs on boards with known bogus DSDT entries
i2c: acpi: Do not instantiate I2C-clients on boards with known bogus DSDT entries
ACPI / x86: Add acpi_quirk_skip_[i2c_client|serdev]_enumeration() helpers
ACPI: scan: Create platform device for BCM4752 and LNV4752 ACPI nodes
ACPI: Use acpi_fetch_acpi_dev() instead of acpi_bus_get_device()
ACPI: scan: Introduce acpi_fetch_acpi_dev()
ACPI: scan: Do not add device IDs from _CID if _HID is not valid
* acpi-pm:
ACPI: PM: Remove redundant cache flushing
ACPI: PM: Avoid CPU cache flush when entering S4
* acpi-power:
ACPI: PM: Emit debug messages when enabling/disabling wakeup power
* acpi-pci:
PCI/ACPI: Fix acpi_pci_osc_control_set() kernel-doc comment
This largely reverts commit 5a7b95fb99. It
breaks suspend with AMD GPUs, and we couldn't incrementally fix it. So,
let's remove the code and go back to the drawing board. We keep the
header extension to not break drivers already populating the regulator.
We expect to re-add the code handling it soon.
Fixes: 5a7b95fb99 ("i2c: core: support bus regulator controlling in adapter")
Reported-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Link: https://lore.kernel.org/r/1295184560.182511.1639075777725@mail.yahoo.com
Reported-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Link: https://lore.kernel.org/r/7143a7147978f4104171072d9f5225d2ce355ec1.camel@yandex.ru
BugLink: https://gitlab.freedesktop.org/drm/amd/-/issues/1850
Tested-by: "Tareque Md.Hanif" <tarequemd.hanif@yahoo.com>
Tested-by: Konstantin Kharlamov <hi-angel@yandex.ru>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Cc: <stable@vger.kernel.org> # 5.14+
When performing an I2C transfer where the last message was a write KASAN
would complain:
BUG: KASAN: slab-out-of-bounds in mpc_i2c_do_action+0x154/0x630
Read of size 2 at addr c814e310 by task swapper/2/0
CPU: 2 PID: 0 Comm: swapper/2 Tainted: G B 5.16.0-rc8 #1
Call Trace:
[e5ee9d50] [c08418e8] dump_stack_lvl+0x4c/0x6c (unreliable)
[e5ee9d70] [c02f8a14] print_address_description.constprop.13+0x64/0x3b0
[e5ee9da0] [c02f9030] kasan_report+0x1f0/0x204
[e5ee9de0] [c0c76ee4] mpc_i2c_do_action+0x154/0x630
[e5ee9e30] [c0c782c4] mpc_i2c_isr+0x164/0x240
[e5ee9e60] [c00f3a04] __handle_irq_event_percpu+0xf4/0x3b0
[e5ee9ec0] [c00f3d40] handle_irq_event_percpu+0x80/0x110
[e5ee9f40] [c00f3e48] handle_irq_event+0x78/0xd0
[e5ee9f60] [c00fcfec] handle_fasteoi_irq+0x19c/0x370
[e5ee9fa0] [c00f1d84] generic_handle_irq+0x54/0x80
[e5ee9fc0] [c0006b54] __do_irq+0x64/0x200
[e5ee9ff0] [c0007958] __do_IRQ+0xe8/0x1c0
[c812dd50] [e3eaab20] 0xe3eaab20
[c812dd90] [c0007a4c] do_IRQ+0x1c/0x30
[c812dda0] [c0000c04] ExternalInput+0x144/0x160
--- interrupt: 500 at arch_cpu_idle+0x34/0x60
NIP: c000b684 LR: c000b684 CTR: c0019688
REGS: c812ddb0 TRAP: 0500 Tainted: G B (5.16.0-rc8)
MSR: 00029002 <CE,EE,ME> CR: 22000488 XER: 20000000
GPR00: c10ef7fc c812de90 c80ff200 c2394718 00000001 00000001 c10e3f90 00000003
GPR08: 00000000 c0019688 c2394718 fc7d625b 22000484 00000000 21e17000 c208228c
GPR16: e3e99284 00000000 ffffffff c2390000 c001bac0 c2082288 c812df60 c001ba60
GPR24: c23949c0 00000018 00080000 00000004 c80ff200 00000002 c2348ee4 c2394718
NIP [c000b684] arch_cpu_idle+0x34/0x60
LR [c000b684] arch_cpu_idle+0x34/0x60
--- interrupt: 500
[c812de90] [c10e3f90] rcu_eqs_enter.isra.60+0xc0/0x110 (unreliable)
[c812deb0] [c10ef7fc] default_idle_call+0xbc/0x230
[c812dee0] [c00af0e8] do_idle+0x1c8/0x200
[c812df10] [c00af3c0] cpu_startup_entry+0x20/0x30
[c812df20] [c001e010] start_secondary+0x5d0/0xba0
[c812dff0] [c00028a0] __secondary_start+0x90/0xdc
This happened because we would overrun the i2c->msgs array on the final
interrupt for the I2C STOP. This didn't happen if the last message was a
read because there is no interrupt in that case. Ensure that we only
access the current message if we are not processing a I2C STOP
condition.
Fixes: 1538d82f46 ("i2c: mpc: Interrupt driven transfer")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq_optional() for DT users only.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
platform_get_resource(pdev, IORESOURCE_IRQ, ..) relies on static
allocation of IRQ resources in DT core code, this causes an issue
when using hierarchical interrupt domains using "interrupts" property
in the node as this bypasses the hierarchical setup and messes up the
irq chaining.
In preparation for removal of static setup of IRQ resource from DT core
code use platform_get_irq().
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Wrong user data may cause warning in i2c_transfer(), ex: zero msgs.
Userspace should not be able to trigger warnings, so this patch adds
validation checks for user data in compact ioctl to prevent reported
warnings
Reported-and-tested-by: syzbot+e417648b303855b91d8a@syzkaller.appspotmail.com
Fixes: 7d5cb45655 ("i2c compat ioctls: move to ->compat_ioctl()")
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
x86 ACPI devices which ship with only Android as their factory image
usually declare a whole bunch of bogus I2C devices in their ACPI tables.
Instantiating I2C clients for these bogus devices causes various issues,
e.g. GPIO/IRQ resource conflicts because sometimes drivers do bind to them.
The Android x86 kernel fork shipped on these devices has some special code
to remove these bogus devices, instead of just fixing the DSDT <sigh>.
Use the new acpi_quirk_skip_i2c_client_enumeration() helper to identify
known boards / acpi devices with this issue, and skip enumerating these.
Note these boards typically do actually have I2C devices, just
different ones then the ones described in their DSDT. The devices
which are actually present are manually instantiated by the
drivers/platform/x86/x86-android-tablets.c kernel module.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
No symbols from the linux/irqchip/chained_irq.h and linux/irqdomain.h
headers are used in the driver, so they can be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated. When converting the existing
calls, it turned out that the termination in the DMA setup and callback
were superfluous and only a side effect of simply calling
rcar_i2c_cleanup_dma(). As either no DMA transfers have been submitted
yet or the last one has successfully completed, there is nothing to
terminate and we can leave it out. So, merge the DMA unmap and cleanup
function to save some code. Then, add a flag if the new cleanup function
needs to terminate DMA. This is only the case for the erorr handling in
the main thread, so we can finally switch from dmaengine_terminate_all()
to dmaengine_terminate_sync() here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated. When converting the existing
calls, it turned out that the termination in the interrupt handlers was
superfluous and only a side effect of simply calling
rcar_i2c_cleanup_dma(). As either no DMA transfers have been submitted
yet or the last one has successfully completed, there is nothing to
terminate and we can leave it out. So, merge the DMA unmap and cleanup
function to save some code. Then, add a flag if the new cleanup function
needs to terminate DMA. This is only the case for the erorr handling in
the main thread, so we can finally switch from dmaengine_terminate_all()
to dmaengine_terminate_sync() here.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
"hsi2c_pclk" clock is optional and may not be present for some SoCs
supported by this driver. Nevertheless, in case the clock is provided
but some error happens during its getting, that error should be handled
properly. Use devm_clk_get_optional() API for that. Also report possible
errors using dev_err_probe() to handle properly -EPROBE_DEFER error (if
clock provider is not ready by the time I2C probe function is executed).
Fixes: 697ad2490c ("i2c: exynos5: Add bus clock support")
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
[wsa: fixed SHA1 of Fixes tag]
Signed-off-by: Wolfram Sang <wsa@kernel.org>
It's fine to call dev_err_probe() in ->probe() when error code is known.
Convert the driver to use dev_err_probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use __maybe_unused for PM functions instead of ifdeffery.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
For better maintenance group MODULE_*() macros together.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Add a note about struct dw_scl_sda_cfg usage to discourage people
of using this structure on new platforms. Instead they should try
hard to put the needed information into firmware descriptions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The data type of hcnt and lcnt in the struct dw_i2c_dev is of type u16.
It's better to have same data type in struct dw_scl_sda_cfg as well.
Reported-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Lakshmi Sowjanya D <lakshmi.sowjanya.d@intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Intel Keem Bay platform supports multi-master operations over same i2c
bus using Synopsys i2c DesignWare IP. When multi-masters initiate i2c
operation simultaneously in a loop, SCL line is stucked low forever
after few i2c operations. Following interrupt sequences are observed
in:
working case: TX_EMPTY, RX_FULL and STOP_DET
non working case: TX_EMPTY, STOP_DET, RX_FULL.
DW_apb_i2c stretches the SCL line when the TX FIFO is empty or when
RX FIFO is full. The DW_apb_i2c master will continue to hold the SCL
line LOW until RX FIFO is read.
Linux kernel i2c DesignWare driver does not handle above non working
sequence. TX_EMPTY, RX_FULL and STOP_DET routine execution are required
in sequence although RX_FULL interrupt is raised after STOP_DET by
hardware. Clear STOP_DET for the following conditions:
(STOP_DET ,RX_FULL, rx_outstanding)
Write Operation: (1, 0, 0)
Read Operation:
RX_FULL followed by STOP_DET: (0, 1, 1) -> (1, 0, 0)
STOP_DET followed by RX_FULL: (1, 0, 1) -> (1, 1, 0)
RX_FULL and STOP_DET together: (1, 1, 1)
Signed-off-by: Tamal Saha <tamal.saha@intel.com>
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches.
-----BEGIN PGP SIGNATURE-----
iQFIBAABCAAyFiEEuvA7XScYQRpenhd+kuxHeUQDJ9wFAmG6YLQUHGhkZWdvZWRl
QHJlZGhhdC5jb20ACgkQkuxHeUQDJ9zwGwf8Csb4wXyc3duBlnX/9jO9REDVKTN9
HhmU2KQm29g10dN2nlFXEOG16xAy8zt3BE7QwniL/R5sUsKTCAEugY8Aqq/4+lFA
vTU+YR9YqZFmEDGMfDngHeh9ZvSWIJS7IEXthxCkgGVhrd2Wl50jKTjVyq1RIDKv
a7B4fOhguFv95xRlnXK+yoVUU7zZPWAgxyCqV0E0JEi8aWE8Y483IRCzcDEyJeDa
HkgZLVwD9l3WQ4uZllVg1q5jfSprHwBa8dFxgcd6mOOYaKowiJ+GjnvnXOto5X72
zsODBJH15VzfVXF5cAqIvzN6nAFR8Mxieei+21iFyUD/Ps1vfWlodFHH2w==
=Q1N9
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-int3472-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86 into media_tree
Signed tag for the immutable platform-drivers-x86-int3472 branch
This branch contains 5.16-rc1 + the pending ACPI/i2c, tps68570 platform_data
and INT3472 driver patches.
* tag 'platform-drivers-x86-int3472-1' of git://git.kernel.org/pub/scm/linux/kernel/git/pdx86/platform-drivers-x86:
platform/x86: int3472: Deal with probe ordering issues
platform/x86: int3472: Pass tps68470_regulator_platform_data to the tps68470-regulator MFD-cell
platform/x86: int3472: Pass tps68470_clk_platform_data to the tps68470-regulator MFD-cell
platform/x86: int3472: Add get_sensor_adev_and_name() helper
platform/x86: int3472: Split into 2 drivers
platform_data: Add linux/platform_data/tps68470.h file
i2c: acpi: Add i2c_acpi_new_device_by_fwnode() function
i2c: acpi: Use acpi_dev_ready_for_enumeration() helper
ACPI: delay enumeration of devices with a _DEP pointing to an INT3472 device
Change i2c_acpi_new_device() into i2c_acpi_new_device_by_fwnode() and
add a static inline wrapper providing the old i2c_acpi_new_device()
behavior.
This is necessary because in some cases we may only have access
to the fwnode / acpi_device and not to the matching physical-node
struct device *.
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Wolfram Sang <wsa@kernel.org>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-4-hdegoede@redhat.com
The clk and regulator frameworks expect clk/regulator consumer-devices
to have info about the consumed clks/regulators described in the device's
fw_node.
To work around cases where this info is not present in the firmware tables,
which is often the case on x86/ACPI devices, both frameworks allow the
provider-driver to attach info about consumers to the clks/regulators
when registering these.
This causes problems with the probe ordering wrt drivers for consumers
of these clks/regulators. Since the lookups are only registered when the
provider-driver binds, trying to get these clks/regulators before then
results in a -ENOENT error for clks and a dummy regulator for regulators.
To ensure the correct probe-ordering the ACPI core has code to defer the
enumeration of consumers affected by this until the providers are ready.
Call the new acpi_dev_ready_for_enumeration() helper to avoid
enumerating / instantiating i2c-clients too early.
Acked-by: Wolfram Sang <wsa@kernel.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Link: https://lore.kernel.org/r/20211203102857.44539-3-hdegoede@redhat.com
Maxime points out that the polling code in mpc_i2c_isr should use the
_atomic API because it is called in an irq context and that the
behaviour of the MCF bit is that it is 1 when the byte transfer is
complete. All of this means the original code was effectively a
udelay(100).
Fix this by using readb_poll_timeout_atomic() and removing the negation
of the break condition.
Fixes: 4a8ac5e45c ("i2c: mpc: Poll for MCF")
Reported-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Tested-by: Maxime Bizon <mbizon@freebox.fr>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Use i2c_timings struct and corresponding methods to get bus clock frequency
Signed-off-by: Akhil R <akhilrajeev@nvidia.com>
Suggested-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Reviewed-by: Dmitry Osipenko <digetx@gmail.com>
Tested-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In interrupt mode we clear the status flags twice, in the interrupt
handler and in i801_check_post(). Remove clearing the status flags
from i801_check_post() and handle polling mode by using the
SMBus unlocking write to also clear the status flags if still set.
To be precise: One could still argue that the status flags are
cleared twice in interrupt mode, but it comes for free.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I see no need to read back the registers to verify that the bits
have actually been cleared. I can't imagine any scenario where
the bits would remain set after a write to them.
Whilst at it, change involved syslog messages to use pci_dbg() et al.
to simplify them.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Tested-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
I2C controller chosen by I2C_EXYNOS5 config option is also suitable for
Exynos850 and ExynosAutoV9 SoCs. State that specifically in I2C_EXYNOS5
symbol help section.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In new Exynos SoCs (like Exynos850) where HSI2C is implemented as a
part of USIv2 block, there are two clocks provided to HSI2C controller:
- PCLK: bus clock (APB), provides access to register interface
- IPCLK: operating IP-core clock; SCL is derived from this one
Both clocks have to be asserted for HSI2C to be functional in that case.
Add code to obtain and enable/disable PCLK in addition to already
handled operating clock. Make it optional though, as older Exynos SoC
variants only have one HSI2C clock.
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Reviewed-by: Chanho Park <chanho61.park@samsung.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
ExynosAutoV9 functioning logic mostly follows I2C_TYPE_EXYNOS7, but
timing calculation and configuration procedure is changed: e.g. only
timing_s3 has to be set now.
Another change of HSI2C controller in ExynosAutoV9 SoC is that it's now
a part of USIv2 IP-core. No changes is needed for I2C driver though, as
all USI related configuration is done in USI driver.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The driver currently assumes that the notify callback is only received
when the device is done with all the queued buffers.
However, this is not true, since the notify callback could be called
without any of the queued buffers being completed (for example, with
virtio-pci and shared interrupts) or with only some of the buffers being
completed (since the driver makes them available to the device in
multiple separate virtqueue_add_sgs() calls).
This can lead to incorrect data on the I2C bus or memory corruption in
the guest if the device operates on buffers which are have been freed by
the driver. (The WARN_ON in the driver is also triggered.)
BUG kmalloc-128 (Tainted: G W ): Poison overwritten
First byte 0x0 instead of 0x6b
Allocated in i2cdev_ioctl_rdwr+0x9d/0x1de age=243 cpu=0 pid=28
memdup_user+0x2e/0xbd
i2cdev_ioctl_rdwr+0x9d/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Freed in i2cdev_ioctl_rdwr+0x1bb/0x1de age=68 cpu=0 pid=28
kfree+0x1bd/0x1cc
i2cdev_ioctl_rdwr+0x1bb/0x1de
i2cdev_ioctl+0x247/0x2ed
vfs_ioctl+0x21/0x30
sys_ioctl+0xb18/0xb41
Fix this by calling virtio_get_buf() from the notify handler like other
virtio drivers and by actually waiting for all the buffers to be
completed.
Fixes: 3cfc883804 ("i2c: virtio: add a virtio i2c frontend driver")
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
The log messages talk about 'bus recovery' while it is not a bus
recovery with 9 pulses but merely a controller reset. Controller resets
are not worth log messages. The 'bus busy' message should be emitted by
upper layers, a busy bus may be expected in some cases.
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Reviewed-by: Alain Volmat <alain.volmat@foss.st.com>
Function stm32f7_i2c_release_bus is always returning 0, hence it
should be a void function. Update the function and remove the
return value error checking code in caller functions.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In a typical read transfer, start completion flag is being set after
read finishes (notice ipd bit 4 being set):
trasnfer poll=0
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 33
This causes I2C transfer being aborted in polled mode from a stop completion
handler:
trasnfer poll=1
i2c start
rk3x-i2c fdd40000.i2c: IRQ: state 1, ipd: 10
i2c read
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 0
rk3x-i2c fdd40000.i2c: IRQ: state 2, ipd: 1b
i2c stop
rk3x-i2c fdd40000.i2c: IRQ: state 4, ipd: 13
i2c stop
rk3x-i2c fdd40000.i2c: unexpected irq in STOP: 0x10
Clearing the START flag after read fixes the issue without any obvious
side effects.
This issue was dicovered on RK3566 when adding support for powering
off the RK817 PMIC.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Reviewed-by: John Keeping <john@metanate.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit e8578547ce. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
This reverts commit 36af188f79. Drivers
should read these values from ACPI tables.
Reported-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
dmaengine_terminate_all() is deprecated in favor of explicitly saying if
it should be sync or async. Here, we use dmaengine_terminate_sync in
i2c_xfer and i2c_smbus_xfer handlers and rely on
dmaengine_terminate_async within interrupt handlers
(transmission error cases).
dmaengine_synchronize is added within i2c_xfer and i2c_smbus_xfer handler
to finalize terminate started in interrupt handlers.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
In case of receiving a NACK, the dma transfer should be stopped
to avoid feeding data into the FIFO.
Also ensure to properly return the proper error code and avoid
waiting for the end of the dma completion in case of
error happening during the transmission.
Fixes: 7ecc8cfde5 ("i2c: i2c-stm32f7: Add DMA support")
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Reviewed-by: Pierre-Yves MORDRET <pierre-yves.mordret@foss.st.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>
Rafał Miłecki