It turns out access to j1939_can_rx_register() needs to be serialized,
otherwise j1939_priv can be corrupted when parallel threads call
j1939_netdev_start() and j1939_can_rx_register() fails. This issue is
thoroughly covered in other commit which serializes access to
j1939_can_rx_register().
Change j1939_netdev_lock type to mutex so that we do not need to remove
GFP_KERNEL from can_rx_register().
j1939_netdev_lock seems to be used in normal contexts where mutex usage
is not prohibited.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Suggested-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20230526171910.227615-2-pchelkin@ispras.ru
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch addresses an issue within the j1939_sk_send_loop_abort()
function in the j1939/socket.c file, specifically in the context of
Transport Protocol (TP) sessions.
Without this patch, when a TP session is initiated and a Clear To Send
(CTS) frame is received from the remote side requesting one data packet,
the kernel dispatches the first Data Transport (DT) frame and then waits
for the next CTS. If the remote side doesn't respond with another CTS,
the kernel aborts due to a timeout. This leads to the user-space
receiving an EPOLLERR on the socket, and the socket becomes active.
However, when trying to read the error queue from the socket with
sock.recvmsg(, , socket.MSG_ERRQUEUE), it returns -EAGAIN,
given that the socket is non-blocking. This situation results in an
infinite loop: the user-space repeatedly calls epoll(), epoll() returns
the socket file descriptor with EPOLLERR, but the socket then blocks on
the recv() of ERRQUEUE.
This patch introduces an additional check for the J1939_SOCK_ERRQUEUE
flag within the j1939_sk_send_loop_abort() function. If the flag is set,
it indicates that the application has subscribed to receive error queue
messages. In such cases, the kernel can communicate the current transfer
state via the error queue. This allows for the function to return early,
preventing the unnecessary setting of the socket into an error state,
and breaking the infinite loop. It is crucial to note that a socket
error is only needed if the application isn't using the error queue, as,
without it, the application wouldn't be aware of transfer issues.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Reported-by: David Jander <david@protonic.nl>
Tested-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/r/20230526081946.715190-1-o.rempel@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The control message provided by J1939 support MSG_CMSG_COMPAT but
blocked recvmsg() syscalls that have set this flag, i.e. on 32bit user
space on 64 bit kernels.
Link: https://github.com/hartkopp/can-isotp/issues/59
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Tested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Link: https://lore.kernel.org/20230505110308.81087-3-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The control message provided by isotp support MSG_CMSG_COMPAT but
blocked recvmsg() syscalls that have set this flag, i.e. on 32bit user
space on 64 bit kernels.
Link: https://github.com/hartkopp/can-isotp/issues/59
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Fixes: 42bf50a179 ("can: isotp: support MSG_TRUNC flag when reading from socket")
Link: https://lore.kernel.org/20230505110308.81087-2-mkl@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEDs2BvajyNKlf9TJQvlAcSiqKBOgFAmQsOSQTHG1rbEBwZW5n
dXRyb25peC5kZQAKCRC+UBxKKooE6N+QB/4w/slgDq0yAYs0GTsRA3Z3IGp8OAlp
PI6g1y9npiR7ffFdnC7ldYRSzTg2sStEKhe0xv80zOPl8IpI82Bz5a7oSb2Oi9tH
Fuf2JF2KYt08VfhGQKmhhcWHSh/vyCrAt14s8P2sCGQPEFBm2N8qrB9hhZera3Xb
gwNG+1nFjuFlUdRxMVQXLmyBdccl/+OLdtU/tI3Y4xm57Fxnghq7DyvmdGumJsbN
6zlyi+FTF3PGgOWglS/2rZeOO4PPWgfsZEeM6jhAt1E2ijtMJSQUl3w1Fpo6dcnq
49wSMFySI8jwpewLgZctZNheb73wvuvAqXnmPm8Krd0hi/apL79Tb1OE
=lDzw
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.4-20230404-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-04-04-2
The first patch is by Oliver Hartkopp and makes the maximum pdu size
of the CAN ISOTP protocol configurable.
The following 5 patches are by Dario Binacchi and add support for the
bxCAN controller by ST.
Geert Uytterhoeven's patch for the rcar_canfd driver fixes a sparse
warning.
Peng Fan's patch adds an optional power-domains property to the
flexcan device tree binding.
Frank Jungclaus adds support for CAN_CTRLMODE_BERR_REPORTING to the
esd_usb driver.
The last patch is by Oliver Hartkopp and converts the USB IDs of the
kvaser_usb driver to hexadecimal values.
* tag 'linux-can-next-for-6.4-20230404-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next:
kvaser_usb: convert USB IDs to hexadecimal values
can: esd_usb: Add support for CAN_CTRLMODE_BERR_REPORTING
dt-bindings: can: fsl,flexcan: add optional power-domains property
can: rcar_canfd: rcar_canfd_probe(): fix plain integer in transceivers[] init
can: bxcan: add support for ST bxCAN controller
ARM: dts: stm32: add pin map for CAN controller on stm32f4
ARM: dts: stm32: add CAN support on stm32f429
dt-bindings: net: can: add STM32 bxcan DT bindings
dt-bindings: arm: stm32: add compatible for syscon gcan node
can: isotp: add module parameter for maximum pdu size
====================
Link: https://lore.kernel.org/r/20230404145908.1714400-1-mkl@pengutronix.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the j1939_tp_tx_dat_new() function, an out-of-bounds memory access
could occur during the memcpy() operation if the size of skb->cb is
larger than the size of struct j1939_sk_buff_cb. This is because the
memcpy() operation uses the size of skb->cb, leading to a read beyond
the struct j1939_sk_buff_cb.
Updated the memcpy() operation to use the size of struct
j1939_sk_buff_cb instead of the size of skb->cb. This ensures that the
memcpy() operation only reads the memory within the bounds of struct
j1939_sk_buff_cb, preventing out-of-bounds memory access.
Additionally, add a BUILD_BUG_ON() to check that the size of skb->cb
is greater than or equal to the size of struct j1939_sk_buff_cb. This
ensures that the skb->cb buffer is large enough to hold the
j1939_sk_buff_cb structure.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Reported-by: Shuangpeng Bai <sjb7183@psu.edu>
Tested-by: Shuangpeng Bai <sjb7183@psu.edu>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://groups.google.com/g/syzkaller/c/G_LL-C3plRs/m/-8xCi6dCAgAJ
Link: https://lore.kernel.org/all/20230404073128.3173900-1-o.rempel@pengutronix.de
Cc: stable@vger.kernel.org
[mkl: rephrase commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
With ISO 15765-2:2016 the PDU size is not limited to 2^12 - 1 (4095)
bytes but can be represented as a 32 bit unsigned integer value which
allows 2^32 - 1 bytes (~4GB). The use-cases like automotive unified
diagnostic services (UDS) and flashing of ECUs still use the small
static buffers which are provided at socket creation time.
When a use-case requires to transfer PDUs up to 1025 kByte the maximum
PDU size can now be extended by setting the module parameter
max_pdu_size. The extended size buffers are only allocated on a
per-socket/connection base when needed at run-time.
changes since v2: https://lore.kernel.org/all/20230313172510.3851-1-socketcan@hartkopp.net
- use ARRAY_SIZE() to reference DEFAULT_MAX_PDU_SIZE only at one place
changes since v1: https://lore.kernel.org/all/20230311143446.3183-1-socketcan@hartkopp.net
- limit the minimum 'max_pdu_size' to 4095 to maintain the classic
behavior before ISO 15765-2:2016
Link: https://github.com/raspberrypi/linux/issues/5371
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230326115911.15094-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Syzkaller reported the following issue:
=====================================================
BUG: KMSAN: uninit-value in aio_rw_done fs/aio.c:1520 [inline]
BUG: KMSAN: uninit-value in aio_write+0x899/0x950 fs/aio.c:1600
aio_rw_done fs/aio.c:1520 [inline]
aio_write+0x899/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
Uninit was created at:
slab_post_alloc_hook mm/slab.h:766 [inline]
slab_alloc_node mm/slub.c:3452 [inline]
__kmem_cache_alloc_node+0x71f/0xce0 mm/slub.c:3491
__do_kmalloc_node mm/slab_common.c:967 [inline]
__kmalloc+0x11d/0x3b0 mm/slab_common.c:981
kmalloc_array include/linux/slab.h:636 [inline]
bcm_tx_setup+0x80e/0x29d0 net/can/bcm.c:930
bcm_sendmsg+0x3a2/0xce0 net/can/bcm.c:1351
sock_sendmsg_nosec net/socket.c:714 [inline]
sock_sendmsg net/socket.c:734 [inline]
sock_write_iter+0x495/0x5e0 net/socket.c:1108
call_write_iter include/linux/fs.h:2189 [inline]
aio_write+0x63a/0x950 fs/aio.c:1600
io_submit_one+0x1d1c/0x3bf0 fs/aio.c:2019
__do_sys_io_submit fs/aio.c:2078 [inline]
__se_sys_io_submit+0x293/0x770 fs/aio.c:2048
__x64_sys_io_submit+0x92/0xd0 fs/aio.c:2048
do_syscall_x64 arch/x86/entry/common.c:50 [inline]
do_syscall_64+0x3d/0xb0 arch/x86/entry/common.c:80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
CPU: 1 PID: 5034 Comm: syz-executor350 Not tainted 6.2.0-rc6-syzkaller-80422-geda666ff2276 #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/12/2023
=====================================================
We can follow the call chain and find that 'bcm_tx_setup' function
calls 'memcpy_from_msg' to copy some content to the newly allocated
frame of 'op->frames'. After that the 'len' field of copied structure
being compared with some constant value (64 or 8). However, if
'memcpy_from_msg' returns an error, we will compare some uninitialized
memory. This triggers 'uninit-value' issue.
This patch will add 'memcpy_from_msg' possible errors processing to
avoid uninit-value issue.
Tested via syzkaller
Reported-by: syzbot+c9bfd85eca611ebf5db1@syzkaller.appspotmail.com
Link: https://syzkaller.appspot.com/bug?id=47f897f8ad958bbde5790ebf389b5e7e0a345089
Signed-off-by: Ivan Orlov <ivan.orlov0322@gmail.com>
Fixes: 6f3b911d5f ("can: bcm: add support for CAN FD frames")
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230314120445.12407-1-ivan.orlov0322@gmail.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This commit addresses a deadlock situation that can occur in certain
scenarios, such as when running data TP/ETP transfer and subscribing to
the error queue while receiving a net down event. The deadlock involves
locks in the following order:
3
j1939_session_list_lock -> active_session_list_lock
j1939_session_activate
...
j1939_sk_queue_activate_next -> sk_session_queue_lock
...
j1939_xtp_rx_eoma_one
2
j1939_sk_queue_drop_all -> sk_session_queue_lock
...
j1939_sk_netdev_event_netdown -> j1939_socks_lock
j1939_netdev_notify
1
j1939_sk_errqueue -> j1939_socks_lock
__j1939_session_cancel -> active_session_list_lock
j1939_tp_rxtimer
CPU0 CPU1
---- ----
lock(&priv->active_session_list_lock);
lock(&jsk->sk_session_queue_lock);
lock(&priv->active_session_list_lock);
lock(&priv->j1939_socks_lock);
The solution implemented in this commit is to move the
j1939_sk_errqueue() call out of the active_session_list_lock context,
thus preventing the deadlock situation.
Reported-by: syzbot+ee1cd780f69483a8616b@syzkaller.appspotmail.com
Fixes: 5b9272e93f ("can: j1939: extend UAPI to notify about RX status")
Co-developed-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Hillf Danton <hdanton@sina.com>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20230324130141.2132787-1-o.rempel@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Introduce a temporary variable to check for an invalid configuration
attempt from user space. Before this patch the value was copied to
the real config variable and rolled back in the case of an error.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230203090807.97100-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEDs2BvajyNKlf9TJQvlAcSiqKBOgFAmPg+r4THG1rbEBwZW5n
dXRyb25peC5kZQAKCRC+UBxKKooE6A44B/0c8jjyLikVE2fEBKkvPk8iRlFKap48
140HNR+1TuVBBPCJTe2Gq3l8fDfFUgUVnFfVDjAQq6pMWufLkz9jVr5uGN7O94v+
tFCjip8NLRTa6ibgQlGrFXl31X5vqT+jV6V4l29wFgbwgOMRrod7wLDo+bHTtuuY
46Sf4GgIazYjxEeZBBsvjnAbraFq0twZFcEz9SyeOxqjR+9+71X4Y3x0kgQuz72N
CrvRng0yFLqbHOBE60iaDqbjuNnwBGTH476pwX25Kj9gVyIH20T45h8tV4j6z2Sq
A42cHKDlWZRWUiWQjGOHHT4igUf//Sfv8WDaFjqobO/DDY+nBA75EPAv
=hWLT
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-6.3-20230206' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2023-02-06
this is a pull request of 47 patches for net-next/master.
The first two patch is by Oliver Hartkopp. One adds missing error
checking to the CAN_GW protocol, the other adds a missing CAN address
family check to the CAN ISO TP protocol.
Thomas Kopp contributes a performance optimization to the mcp251xfd
driver.
The next 11 patches are by Geert Uytterhoeven and add support for
R-Car V4H systems to the rcar_canfd driver.
Stephane Grosjean and Lukas Magel contribute 8 patches to the peak_usb
driver, which add support for configurable CAN channel ID.
The last 17 patches are by me and target the CAN bit timing
configuration. The bit timing is cleaned up, error messages are
improved and forwarded to user space via NL_SET_ERR_MSG_FMT() instead
of netdev_err(), and the SJW handling is updated, including the
definition of a new default value that will benefit CAN-FD
controllers, by increasing their oscillator tolerance.
* tag 'linux-can-next-for-6.3-20230206' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next: (47 commits)
can: bittiming: can_validate_bitrate(): report error via netlink
can: bittiming: can_calc_bittiming(): convert from netdev_err() to NL_SET_ERR_MSG_FMT()
can: bittiming: can_calc_bittiming(): clean up SJW handling
can: bittiming: can_sjw_set_default(): use Phase Seg2 / 2 as default for SJW
can: bittiming: can_sjw_check(): check that SJW is not longer than either Phase Buffer Segment
can: bittiming: can_sjw_check(): report error via netlink and harmonize error value
can: bittiming: can_fixup_bittiming(): report error via netlink and harmonize error value
can: bittiming: factor out can_sjw_set_default() and can_sjw_check()
can: bittiming: can_changelink() pass extack down callstack
can: netlink: can_changelink(): convert from netdev_err() to NL_SET_ERR_MSG_FMT()
can: netlink: can_validate(): validate sample point for CAN and CAN-FD
can: dev: register_candev(): bail out if both fixed bit rates and bit timing constants are provided
can: dev: register_candev(): ensure that bittiming const are valid
can: bittiming: can_get_bittiming(): use direct return and remove unneeded else
can: bittiming: can_fixup_bittiming(): set effective tq
can: bittiming: can_fixup_bittiming(): use CAN_SYNC_SEG instead of 1
can: bittiming(): replace open coded variants of can_bit_time()
can: peak_usb: Reorder include directives alphabetically
can: peak_usb: align CAN channel ID format in log with sysfs attribute
can: peak_usb: export PCAN CAN channel ID as sysfs device attribute
...
====================
Link: https://lore.kernel.org/r/20230206131620.2758724-1-mkl@pengutronix.de
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
The ISO 11783-5 standard, in "4.5.2 - Address claim requirements", states:
d) No CF shall begin, or resume, transmission on the network until 250
ms after it has successfully claimed an address except when
responding to a request for address-claimed.
But "Figure 6" and "Figure 7" in "4.5.4.2 - Address-claim
prioritization" show that the CF begins the transmission after 250 ms
from the first AC (address-claimed) message even if it sends another AC
message during that time window to resolve the address contention with
another CF.
As stated in "4.4.2.3 - Address-claimed message":
In order to successfully claim an address, the CF sending an address
claimed message shall not receive a contending claim from another CF
for at least 250 ms.
As stated in "4.4.3.2 - NAME management (NM) message":
1) A commanding CF can
d) request that a CF with a specified NAME transmit the address-
claimed message with its current NAME.
2) A target CF shall
d) send an address-claimed message in response to a request for a
matching NAME
Taking the above arguments into account, the 250 ms wait is requested
only during network initialization.
Do not restart the timer on AC message if both the NAME and the address
match and so if the address has already been claimed (timer has expired)
or the AC message has been sent to resolve the contention with another
CF (timer is still running).
Signed-off-by: Devid Antonio Filoni <devid.filoni@egluetechnologies.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20221125170418.34575-1-devid.filoni@egluetechnologies.com
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To send CAN traffic back to the incoming interface a special flag has to
be set. When creating a routing job for identical interfaces without this
flag the rule is created but has no effect.
This patch adds an error return value in the case that the CAN interfaces
are identical but the CGW_FLAGS_CAN_IIF_TX_OK flag was not set.
Reported-by: Jannik Hartung <jannik.hartung@tu-bs.de>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230125055407.2053-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The timer for the transmission of isotp PDUs formerly had two functions:
1. send two consecutive frames with a given time gap
2. monitor the timeouts for flow control frames and the echo frames
This led to larger txstate checks and potentially to a problem discovered
by syzbot which enabled the panic_on_warn feature while testing.
The former 'txtimer' function is split into 'txfrtimer' and 'txtimer'
to handle the two above functionalities with separate timer callbacks.
The two simplified timers now run in one-shot mode and make the state
transitions (especially with isotp_rcv_echo) better understandable.
Fixes: 866337865f ("can: isotp: fix tx state handling for echo tx processing")
Reported-by: syzbot+5aed6c3aaba661f5b917@syzkaller.appspotmail.com
Cc: stable@vger.kernel.org # >= v6.0
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230104145701.2422-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
When wait_event_interruptible() has been interrupted by a signal the
tx.state value might not be ISOTP_IDLE. Force the state machines
into idle state to inhibit the timer handlers to continue working.
Fixes: 866337865f ("can: isotp: fix tx state handling for echo tx processing")
Cc: stable@vger.kernel.org
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230112192347.1944-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
A CAN XL device is always capable to process CAN FD frames. The former
check when sending CAN FD frames relied on the existence of a CAN FD
device and did not check for a CAN XL device that would be correct
too.
With this patch the CAN FD feature is enabled automatically when CAN
XL is switched on - and CAN FD cannot be switch off while CAN XL is
enabled.
This precondition also leads to a clean up and reduction of checks in
the hot path in raw_rcv() and raw_sendmsg(). Some conditions are
reordered to handle simple checks first.
changes since v1: https://lore.kernel.org/all/20230131091012.50553-1-socketcan@hartkopp.net
- fixed typo: devive -> device
changes since v2: https://lore.kernel.org/all/20230131091824.51026-1-socketcan@hartkopp.net/
- reorder checks in if statements to handle simple checks first
Fixes: 626332696d ("can: raw: add CAN XL support")
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20230131105613.55228-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The conclusion "j1939_session_deactivate() should be called with a
session ref-count of at least 2" is incorrect. In some concurrent
scenarios, j1939_session_deactivate can be called with the session
ref-count less than 2. But there is not any problem because it
will check the session active state before session putting in
j1939_session_deactivate_locked().
Here is the concurrent scenario of the problem reported by syzbot
and my reproduction log.
cpu0 cpu1
j1939_xtp_rx_eoma
j1939_xtp_rx_abort_one
j1939_session_get_by_addr [kref == 2]
j1939_session_get_by_addr [kref == 3]
j1939_session_deactivate [kref == 2]
j1939_session_put [kref == 1]
j1939_session_completed
j1939_session_deactivate
WARN_ON_ONCE(kref < 2)
=====================================================
WARNING: CPU: 1 PID: 21 at net/can/j1939/transport.c:1088 j1939_session_deactivate+0x5f/0x70
CPU: 1 PID: 21 Comm: ksoftirqd/1 Not tainted 5.14.0-rc7+ #32
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.13.0-1ubuntu1 04/01/2014
RIP: 0010:j1939_session_deactivate+0x5f/0x70
Call Trace:
j1939_session_deactivate_activate_next+0x11/0x28
j1939_xtp_rx_eoma+0x12a/0x180
j1939_tp_recv+0x4a2/0x510
j1939_can_recv+0x226/0x380
can_rcv_filter+0xf8/0x220
can_receive+0x102/0x220
? process_backlog+0xf0/0x2c0
can_rcv+0x53/0xf0
__netif_receive_skb_one_core+0x67/0x90
? process_backlog+0x97/0x2c0
__netif_receive_skb+0x22/0x80
Fixes: 0c71437dd5 ("can: j1939: j1939_session_deactivate(): clarify lifetime of session object")
Reported-by: syzbot+9981a614060dcee6eeca@syzkaller.appspotmail.com
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20210906094200.95868-1-william.xuanziyang@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Core
----
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations.
- Add inet drop monitor support.
- A few GRO performance improvements.
- Add infrastructure for atomic dev stats, addressing long standing
data races.
- De-duplicate common code between OVS and conntrack offloading
infrastructure.
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements.
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up
the workload with the number of available CPUs.
- Add the helper support for connection-tracking OVS offload.
BPF
---
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF.
- Make cgroup local storage available to non-cgroup attached BPF
programs.
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers.
- A relevant bunch of BPF verifier fixes and improvements.
- Veristat tool improvements to support custom filtering, sorting,
and replay of results.
- Add LLVM disassembler as default library for dumping JITed code.
- Lots of new BPF documentation for various BPF maps.
- Add bpf_rcu_read_{,un}lock() support for sleepable programs.
- Add RCU grace period chaining to BPF to wait for the completion
of access from both sleepable and non-sleepable BPF programs.
- Add support storing struct task_struct objects as kptrs in maps.
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values.
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions.
Protocols
---------
- TCP: implement Protective Load Balancing across switch links.
- TCP: allow dynamically disabling TCP-MD5 static key, reverting
back to fast[er]-path.
- UDP: Introduce optional per-netns hash lookup table.
- IPv6: simplify and cleanup sockets disposal.
- Netlink: support different type policies for each generic
netlink operation.
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support.
- MPTCP: add netlink notification support for listener sockets
events.
- SCTP: add VRF support, allowing sctp sockets binding to VRF
devices.
- Add bridging MAC Authentication Bypass (MAB) support.
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios.
- More work for Wi-Fi 7 support, comprising conversion of all
the existing drivers to internal TX queue usage.
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading.
- IPSec: extended ack support for more descriptive XFRM error
reporting.
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking.
- IEEE 802154: synchronous send frame and extended filtering
support, initial support for scanning available 15.4 networks.
- Tun: bump the link speed from 10Mbps to 10Gbps.
- Tun/VirtioNet: implement UDP segmentation offload support.
Driver API
----------
- PHY/SFP: improve power level switching between standard
level 1 and the higher power levels.
- New API for netdev <-> devlink_port linkage.
- PTP: convert existing drivers to new frequency adjustment
implementation.
- DSA: add support for rx offloading.
- Autoload DSA tagging driver when dynamically changing protocol.
- Add new PCP and APPTRUST attributes to Data Center Bridging.
- Add configuration support for 800Gbps link speed.
- Add devlink port function attribute to enable/disable RoCE and
migratable.
- Extend devlink-rate to support strict prioriry and weighted fair
queuing.
- Add devlink support to directly reading from region memory.
- New device tree helper to fetch MAC address from nvmem.
- New big TCP helper to simplify temporary header stripping.
New hardware / drivers
----------------------
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches.
- Marvel Prestera AC5X Ethernet Switch.
- WangXun 10 Gigabit NIC.
- Motorcomm yt8521 Gigabit Ethernet.
- Microchip ksz9563 Gigabit Ethernet Switch.
- Microsoft Azure Network Adapter.
- Linux Automation 10Base-T1L adapter.
- PHY:
- Aquantia AQR112 and AQR412.
- Motorcomm YT8531S.
- PTP:
- Orolia ART-CARD.
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices.
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices.
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets.
- Realtek RTL8852BE and RTL8723DS.
- Cypress.CYW4373A0 WiFi + Bluetooth combo device.
Drivers
-------
- CAN:
- gs_usb: bus error reporting support.
- kvaser_usb: listen only and bus error reporting support.
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping.
- implement devlink-rate support.
- support direct read from memory.
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate.
- Support for enhanced events compression.
- extend H/W offload packet manipulation capabilities.
- implement IPSec packet offload mode.
- nVidia/Mellanox (mlx4):
- better big TCP support.
- Netronome Ethernet NICs (nfp):
- IPsec offload support.
- add support for multicast filter.
- Broadcom:
- RSS and PTP support improvements.
- AMD/SolarFlare:
- netlink extened ack improvements.
- add basic flower matches to offload, and related stats.
- Virtual NICs:
- ibmvnic: introduce affinity hint support.
- small / embedded:
- FreeScale fec: add initial XDP support.
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood.
- TI am65-cpsw: add suspend/resume support.
- Mediatek MT7986: add RX wireless wthernet dispatch support.
- Realtek 8169: enable GRO software interrupt coalescing per
default.
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP.
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support.
- add ip6gre support.
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support.
- enable flow offload support.
- Renesas:
- add rswitch R-Car Gen4 gPTP support.
- Microchip (lan966x):
- add full XDP support.
- add TC H/W offload via VCAP.
- enable PTP on bridge interfaces.
- Microchip (ksz8):
- add MTU support for KSZ8 series.
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan.
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support.
- add ack signal support.
- enable coredump support.
- remain_on_channel support.
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities.
- 320 MHz channels support.
- RealTek WiFi (rtw89):
- new dynamic header firmware format support.
- wake-over-WLAN support.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEEg1AjqC77wbdLX2LbKSR5jcyPE6QFAmOYXUcSHHBhYmVuaUBy
ZWRoYXQuY29tAAoJECkkeY3MjxOk8zQP/R7BZtbJMTPiWkRnSoKHnAyupDVwrz5U
ktukLkwPsCyJuEbAjgxrxf4EEEQ9uq2FFlxNSYuKiiQMqIpFxV6KED7LCUygn4Tc
kxtkp0Q+5XiqisWlQmtfExf2OjuuPqcjV9tWCDBI6GebKUbfNwY/eI44RcMu4BSv
DzIlW5GkX/kZAPqnnuqaLsN3FudDTJHGEAD7NbA++7wJ076RWYSLXlFv0Z+SCSPS
H8/PEG0/ZK/65rIWMAFRClJ9BNIDwGVgp0GrsIvs1gqbRUOlA1hl1rDM21TqtNFf
5QPQT7sIfTcCE/nerxKJD5JE3JyP+XRlRn96PaRw3rt4MgI6I/EOj/HOKQ5tMCNc
oPiqb7N70+hkLZyr42qX+vN9eDPjp2koEQm7EO2Zs+/534/zWDs24Zfk/Aa1ps0I
Fa82oGjAgkBhGe/FZ6i5cYoLcyxqRqZV1Ws9XQMl72qRC7/BwvNbIW6beLpCRyeM
yYIU+0e9dEm+wHQEdh2niJuVtR63hy8tvmPx56lyh+6u0+pondkwbfSiC5aD3kAC
ikKsN5DyEsdXyiBAlytCEBxnaOjQy4RAz+3YXSiS0eBNacXp03UUrNGx4Pzpu/D0
QLFJhBnMFFCgy5to8/DvKnrTPgZdSURwqbIUcZdvU21f1HLR8tUTpaQnYffc/Whm
V8gnt1EL+0cc
=CbJC
-----END PGP SIGNATURE-----
Merge tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Paolo Abeni:
"Core:
- Allow live renaming when an interface is up
- Add retpoline wrappers for tc, improving considerably the
performances of complex queue discipline configurations
- Add inet drop monitor support
- A few GRO performance improvements
- Add infrastructure for atomic dev stats, addressing long standing
data races
- De-duplicate common code between OVS and conntrack offloading
infrastructure
- A bunch of UBSAN_BOUNDS/FORTIFY_SOURCE improvements
- Netfilter: introduce packet parser for tunneled packets
- Replace IPVS timer-based estimators with kthreads to scale up the
workload with the number of available CPUs
- Add the helper support for connection-tracking OVS offload
BPF:
- Support for user defined BPF objects: the use case is to allocate
own objects, build own object hierarchies and use the building
blocks to build own data structures flexibly, for example, linked
lists in BPF
- Make cgroup local storage available to non-cgroup attached BPF
programs
- Avoid unnecessary deadlock detection and failures wrt BPF task
storage helpers
- A relevant bunch of BPF verifier fixes and improvements
- Veristat tool improvements to support custom filtering, sorting,
and replay of results
- Add LLVM disassembler as default library for dumping JITed code
- Lots of new BPF documentation for various BPF maps
- Add bpf_rcu_read_{,un}lock() support for sleepable programs
- Add RCU grace period chaining to BPF to wait for the completion of
access from both sleepable and non-sleepable BPF programs
- Add support storing struct task_struct objects as kptrs in maps
- Improve helper UAPI by explicitly defining BPF_FUNC_xxx integer
values
- Add libbpf *_opts API-variants for bpf_*_get_fd_by_id() functions
Protocols:
- TCP: implement Protective Load Balancing across switch links
- TCP: allow dynamically disabling TCP-MD5 static key, reverting back
to fast[er]-path
- UDP: Introduce optional per-netns hash lookup table
- IPv6: simplify and cleanup sockets disposal
- Netlink: support different type policies for each generic netlink
operation
- MPTCP: add MSG_FASTOPEN and FastOpen listener side support
- MPTCP: add netlink notification support for listener sockets events
- SCTP: add VRF support, allowing sctp sockets binding to VRF devices
- Add bridging MAC Authentication Bypass (MAB) support
- Extensions for Ethernet VPN bridging implementation to better
support multicast scenarios
- More work for Wi-Fi 7 support, comprising conversion of all the
existing drivers to internal TX queue usage
- IPSec: introduce a new offload type (packet offload) allowing
complete header processing and crypto offloading
- IPSec: extended ack support for more descriptive XFRM error
reporting
- RXRPC: increase SACK table size and move processing into a
per-local endpoint kernel thread, reducing considerably the
required locking
- IEEE 802154: synchronous send frame and extended filtering support,
initial support for scanning available 15.4 networks
- Tun: bump the link speed from 10Mbps to 10Gbps
- Tun/VirtioNet: implement UDP segmentation offload support
Driver API:
- PHY/SFP: improve power level switching between standard level 1 and
the higher power levels
- New API for netdev <-> devlink_port linkage
- PTP: convert existing drivers to new frequency adjustment
implementation
- DSA: add support for rx offloading
- Autoload DSA tagging driver when dynamically changing protocol
- Add new PCP and APPTRUST attributes to Data Center Bridging
- Add configuration support for 800Gbps link speed
- Add devlink port function attribute to enable/disable RoCE and
migratable
- Extend devlink-rate to support strict prioriry and weighted fair
queuing
- Add devlink support to directly reading from region memory
- New device tree helper to fetch MAC address from nvmem
- New big TCP helper to simplify temporary header stripping
New hardware / drivers:
- Ethernet:
- Marvel Octeon CNF95N and CN10KB Ethernet Switches
- Marvel Prestera AC5X Ethernet Switch
- WangXun 10 Gigabit NIC
- Motorcomm yt8521 Gigabit Ethernet
- Microchip ksz9563 Gigabit Ethernet Switch
- Microsoft Azure Network Adapter
- Linux Automation 10Base-T1L adapter
- PHY:
- Aquantia AQR112 and AQR412
- Motorcomm YT8531S
- PTP:
- Orolia ART-CARD
- WiFi:
- MediaTek Wi-Fi 7 (802.11be) devices
- RealTek rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du USB
devices
- Bluetooth:
- Broadcom BCM4377/4378/4387 Bluetooth chipsets
- Realtek RTL8852BE and RTL8723DS
- Cypress.CYW4373A0 WiFi + Bluetooth combo device
Drivers:
- CAN:
- gs_usb: bus error reporting support
- kvaser_usb: listen only and bus error reporting support
- Ethernet NICs:
- Intel (100G):
- extend action skbedit to RX queue mapping
- implement devlink-rate support
- support direct read from memory
- nVidia/Mellanox (mlx5):
- SW steering improvements, increasing rules update rate
- Support for enhanced events compression
- extend H/W offload packet manipulation capabilities
- implement IPSec packet offload mode
- nVidia/Mellanox (mlx4):
- better big TCP support
- Netronome Ethernet NICs (nfp):
- IPsec offload support
- add support for multicast filter
- Broadcom:
- RSS and PTP support improvements
- AMD/SolarFlare:
- netlink extened ack improvements
- add basic flower matches to offload, and related stats
- Virtual NICs:
- ibmvnic: introduce affinity hint support
- small / embedded:
- FreeScale fec: add initial XDP support
- Marvel mv643xx_eth: support MII/GMII/RGMII modes for Kirkwood
- TI am65-cpsw: add suspend/resume support
- Mediatek MT7986: add RX wireless wthernet dispatch support
- Realtek 8169: enable GRO software interrupt coalescing per
default
- Ethernet high-speed switches:
- Microchip (sparx5):
- add support for Sparx5 TC/flower H/W offload via VCAP
- Mellanox mlxsw:
- add 802.1X and MAC Authentication Bypass offload support
- add ip6gre support
- Embedded Ethernet switches:
- Mediatek (mtk_eth_soc):
- improve PCS implementation, add DSA untag support
- enable flow offload support
- Renesas:
- add rswitch R-Car Gen4 gPTP support
- Microchip (lan966x):
- add full XDP support
- add TC H/W offload via VCAP
- enable PTP on bridge interfaces
- Microchip (ksz8):
- add MTU support for KSZ8 series
- Qualcomm 802.11ax WiFi (ath11k):
- support configuring channel dwell time during scan
- MediaTek WiFi (mt76):
- enable Wireless Ethernet Dispatch (WED) offload support
- add ack signal support
- enable coredump support
- remain_on_channel support
- Intel WiFi (iwlwifi):
- enable Wi-Fi 7 Extremely High Throughput (EHT) PHY capabilities
- 320 MHz channels support
- RealTek WiFi (rtw89):
- new dynamic header firmware format support
- wake-over-WLAN support"
* tag 'net-next-6.2' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2002 commits)
ipvs: fix type warning in do_div() on 32 bit
net: lan966x: Remove a useless test in lan966x_ptp_add_trap()
net: ipa: add IPA v4.7 support
dt-bindings: net: qcom,ipa: Add SM6350 compatible
bnxt: Use generic HBH removal helper in tx path
IPv6/GRO: generic helper to remove temporary HBH/jumbo header in driver
selftests: forwarding: Add bridge MDB test
selftests: forwarding: Rename bridge_mdb test
bridge: mcast: Support replacement of MDB port group entries
bridge: mcast: Allow user space to specify MDB entry routing protocol
bridge: mcast: Allow user space to add (*, G) with a source list and filter mode
bridge: mcast: Add support for (*, G) with a source list and filter mode
bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source
bridge: mcast: Add a flag for user installed source entries
bridge: mcast: Expose __br_multicast_del_group_src()
bridge: mcast: Expose br_multicast_new_group_src()
bridge: mcast: Add a centralized error path
bridge: mcast: Place netlink policy before validation functions
bridge: mcast: Split (*, G) and (S, G) addition into different functions
bridge: mcast: Do not derive entry type from its filter mode
...
-----BEGIN PGP SIGNATURE-----
iQIzBAABCAAdFiEEq5lC5tSkz8NBJiCnSfxwEqXeA64FAmOU+U8ACgkQSfxwEqXe
A67NnQ//Y5DltmvibyPd7r1TFT2gUYv+Rx3sUV9ZE1NYptd/SWhhcL8c5FZ70Fuw
bSKCa1uiWjOxosjXT1kGrWq3de7q7oUpAPSOGxgxzoaNURIt58N/ajItCX/4Au8I
RlGAScHy5e5t41/26a498kB6qJ441fBEqCYKQpPLINMBAhe8TQ+NVp0rlpUwNHFX
WrUGg4oKWxdBIW3HkDirQjJWDkkAiklRTifQh/Al4b6QDbOnRUGGCeckNOhixsvS
waHWTld+Td8jRrA4b82tUb2uVZ2/b8dEvj/A8CuTv4yC0lywoyMgBWmJAGOC+UmT
ZVNdGW02Jc2T+Iap8ZdsEmeLHNqbli4+IcbY5xNlov+tHJ2oz41H9TZoYKbudlr6
/ReAUPSn7i50PhbQlEruj3eg+M2gjOeh8OF8UKwwRK8PghvyWQ1ScW0l3kUhPIhI
PdIG6j4+D2mJc1FIj2rTVB+Bg933x6S+qx4zDxGlNp62AARUFYf6EgyD6aXFQVuX
RxcKb6cjRuFkzFiKc8zkqg5edZH+IJcPNuIBmABqTGBOxbZWURXzIQvK/iULqZa4
CdGAFIs6FuOh8pFHLI3R4YoHBopbHup/xKDEeAO9KZGyeVIuOSERDxxo5f/ITzcq
APvT77DFOEuyvanr8RMqqh0yUjzcddXqw9+ieufsAyDwjD9DTuE=
=QRhK
-----END PGP SIGNATURE-----
Merge tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random
Pull random number generator updates from Jason Donenfeld:
- Replace prandom_u32_max() and various open-coded variants of it,
there is now a new family of functions that uses fast rejection
sampling to choose properly uniformly random numbers within an
interval:
get_random_u32_below(ceil) - [0, ceil)
get_random_u32_above(floor) - (floor, U32_MAX]
get_random_u32_inclusive(floor, ceil) - [floor, ceil]
Coccinelle was used to convert all current users of
prandom_u32_max(), as well as many open-coded patterns, resulting in
improvements throughout the tree.
I'll have a "late" 6.1-rc1 pull for you that removes the now unused
prandom_u32_max() function, just in case any other trees add a new
use case of it that needs to converted. According to linux-next,
there may be two trivial cases of prandom_u32_max() reintroductions
that are fixable with a 's/.../.../'. So I'll have for you a final
conversion patch doing that alongside the removal patch during the
second week.
This is a treewide change that touches many files throughout.
- More consistent use of get_random_canary().
- Updates to comments, documentation, tests, headers, and
simplification in configuration.
- The arch_get_random*_early() abstraction was only used by arm64 and
wasn't entirely useful, so this has been replaced by code that works
in all relevant contexts.
- The kernel will use and manage random seeds in non-volatile EFI
variables, refreshing a variable with a fresh seed when the RNG is
initialized. The RNG GUID namespace is then hidden from efivarfs to
prevent accidental leakage.
These changes are split into random.c infrastructure code used in the
EFI subsystem, in this pull request, and related support inside of
EFISTUB, in Ard's EFI tree. These are co-dependent for full
functionality, but the order of merging doesn't matter.
- Part of the infrastructure added for the EFI support is also used for
an improvement to the way vsprintf initializes its siphash key,
replacing an sleep loop wart.
- The hardware RNG framework now always calls its correct random.c
input function, add_hwgenerator_randomness(), rather than sometimes
going through helpers better suited for other cases.
- The add_latent_entropy() function has long been called from the fork
handler, but is a no-op when the latent entropy gcc plugin isn't
used, which is fine for the purposes of latent entropy.
But it was missing out on the cycle counter that was also being mixed
in beside the latent entropy variable. So now, if the latent entropy
gcc plugin isn't enabled, add_latent_entropy() will expand to a call
to add_device_randomness(NULL, 0), which adds a cycle counter,
without the absent latent entropy variable.
- The RNG is now reseeded from a delayed worker, rather than on demand
when used. Always running from a worker allows it to make use of the
CPU RNG on platforms like S390x, whose instructions are too slow to
do so from interrupts. It also has the effect of adding in new inputs
more frequently with more regularity, amounting to a long term
transcript of random values. Plus, it helps a bit with the upcoming
vDSO implementation (which isn't yet ready for 6.2).
- The jitter entropy algorithm now tries to execute on many different
CPUs, round-robining, in hopes of hitting even more memory latencies
and other unpredictable effects. It also will mix in a cycle counter
when the entropy timer fires, in addition to being mixed in from the
main loop, to account more explicitly for fluctuations in that timer
firing. And the state it touches is now kept within the same cache
line, so that it's assured that the different execution contexts will
cause latencies.
* tag 'random-6.2-rc1-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/crng/random: (23 commits)
random: include <linux/once.h> in the right header
random: align entropy_timer_state to cache line
random: mix in cycle counter when jitter timer fires
random: spread out jitter callback to different CPUs
random: remove extraneous period and add a missing one in comments
efi: random: refresh non-volatile random seed when RNG is initialized
vsprintf: initialize siphash key using notifier
random: add back async readiness notifier
random: reseed in delayed work rather than on-demand
random: always mix cycle counter in add_latent_entropy()
hw_random: use add_hwgenerator_randomness() for early entropy
random: modernize documentation comment on get_random_bytes()
random: adjust comment to account for removed function
random: remove early archrandom abstraction
random: use random.trust_{bootloader,cpu} command line option only
stackprotector: actually use get_random_canary()
stackprotector: move get_random_canary() into stackprotector.h
treewide: use get_random_u32_inclusive() when possible
treewide: use get_random_u32_{above,below}() instead of manual loop
treewide: use get_random_u32_below() instead of deprecated function
...
Add support for SO_MARK to the CAN_RAW protocol. This makes it
possible to add traffic control filters based on the fwmark.
Link: https://lore.kernel.org/all/20221210113653.170346-1-mkl@pengutronix.de
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Analogue to commit 8aa59e3559 ("can: af_can: fix NULL pointer
dereference in can_rx_register()") we need to check for a missing
initialization of ml_priv in the receive path of CAN frames.
Since commit 4e096a1886 ("net: introduce CAN specific pointer in the
struct net_device") the check for dev->type to be ARPHRD_CAN is not
sufficient anymore since bonding or tun netdevices claim to be CAN
devices but do not initialize ml_priv accordingly.
Fixes: 4e096a1886 ("net: introduce CAN specific pointer in the struct net_device")
Reported-by: syzbot+2d7f58292cb5b29eb5ad@syzkaller.appspotmail.com
Reported-by: Wei Chen <harperchen1110@gmail.com>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20221206201259.3028-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This is a simple mechanical transformation done by:
@@
expression E;
@@
- prandom_u32_max
+ get_random_u32_below
(E)
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Darrick J. Wong <djwong@kernel.org> # for xfs
Reviewed-by: SeongJae Park <sj@kernel.org> # for damon
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com> # for infiniband
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> # for arm
Acked-by: Ulf Hansson <ulf.hansson@linaro.org> # for mmc
Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
In commit 4b7fe92c06 ("can: isotp: add local echo tx processing for
consecutive frames") the data flow for consecutive frames (CF) has been
reworked to improve the reliability of long data transfers.
This rework did not touch the transmission and the tx state changes of
single frame (SF) transfers which likely led to the WARN in the
isotp_tx_timer_handler() catching a wrong tx state. This patch makes use
of the improved frame processing for SF frames and sets the ISOTP_SENDING
state in isotp_sendmsg() within the cmpxchg() condition handling.
A review of the state machine and the timer handling additionally revealed
a missing echo timeout handling in the case of the burst mode in
isotp_rcv_echo() and removes a potential timer configuration uncertainty
in isotp_rcv_fc() when the receiver requests consecutive frames.
Fixes: 4b7fe92c06 ("can: isotp: add local echo tx processing for consecutive frames")
Link: https://lore.kernel.org/linux-can/CAO4mrfe3dG7cMP1V5FLUkw7s+50c9vichigUMQwsxX4M=45QEw@mail.gmail.com/T/#u
Reported-by: Wei Chen <harperchen1110@gmail.com>
Cc: stable@vger.kernel.org # v6.0
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20221104142551.16924-1-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
It causes NULL pointer dereference when testing as following:
(a) use syscall(__NR_socket, 0x10ul, 3ul, 0) to create netlink socket.
(b) use syscall(__NR_sendmsg, ...) to create bond link device and vxcan
link device, and bind vxcan device to bond device (can also use
ifenslave command to bind vxcan device to bond device).
(c) use syscall(__NR_socket, 0x1dul, 3ul, 1) to create CAN socket.
(d) use syscall(__NR_bind, ...) to bind the bond device to CAN socket.
The bond device invokes the can-raw protocol registration interface to
receive CAN packets. However, ml_priv is not allocated to the dev,
dev_rcv_lists is assigned to NULL in can_rx_register(). In this case,
it will occur the NULL pointer dereference issue.
The following is the stack information:
BUG: kernel NULL pointer dereference, address: 0000000000000008
PGD 122a4067 P4D 122a4067 PUD 1223c067 PMD 0
Oops: 0000 [#1] PREEMPT SMP
RIP: 0010:can_rx_register+0x12d/0x1e0
Call Trace:
<TASK>
raw_enable_filters+0x8d/0x120
raw_enable_allfilters+0x3b/0x130
raw_bind+0x118/0x4f0
__sys_bind+0x163/0x1a0
__x64_sys_bind+0x1e/0x30
do_syscall_64+0x35/0x80
entry_SYSCALL_64_after_hwframe+0x63/0xcd
</TASK>
Fixes: 4e096a1886 ("net: introduce CAN specific pointer in the struct net_device")
Signed-off-by: Zhengchao Shao <shaozhengchao@huawei.com>
Reviewed-by: Marc Kleine-Budde <mkl@pengutronix.de>
Link: https://lore.kernel.org/all/20221028085650.170470-1-shaozhengchao@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
In can_init(), dev_add_pack(&canxl_packet) is added but not removed in
can_exit(). It breaks the packet handler list and can make kernel
panic when can_init() is called for the second time.
| > modprobe can && rmmod can
| > rmmod xxx && modprobe can
|
| BUG: unable to handle page fault for address: fffffbfff807d7f4
| RIP: 0010:dev_add_pack+0x133/0x1f0
| Call Trace:
| <TASK>
| can_init+0xaa/0x1000 [can]
| do_one_initcall+0xd3/0x4e0
| ...
Fixes: fb08cba12b ("can: canxl: update CAN infrastructure for CAN XL frames")
Signed-off-by: Chen Zhongjin <chenzhongjin@huawei.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20221031033053.37849-1-chenzhongjin@huawei.com
[mkl: adjust subject and commit message]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
drivers/net/can/usb/kvaser_usb/kvaser_usb_leaf.c
2871edb32f ("can: kvaser_usb: Fix possible completions during init_completion")
abb8670938 ("can: kvaser_usb_leaf: Ignore stale bus-off after start")
8d21f5927a ("can: kvaser_usb_leaf: Fix improved state not being reported")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
It is not allowed to call kfree_skb() from hardware interrupt context
or with interrupts being disabled. The skb is unlinked from the queue,
so it can be freed after spin_unlock_irqrestore().
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20221027091237.2290111-1-yangyingliang@huawei.com
Cc: stable@vger.kernel.org
[mkl: adjust subject]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
If can_send() fail, it should not update frames_abs counter
in bcm_can_tx(). Add the result check for can_send() in bcm_can_tx().
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Suggested-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/all/9851878e74d6d37aee2f1ee76d68361a46f89458.1663206163.git.william.xuanziyang@huawei.com
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Now, register_netdevice_notifier() and register_pernet_subsys() are both
after can_proto_register(). It can create CAN_BCM socket and process socket
once can_proto_register() successfully, so it is possible missing notifier
event or proc node creation because notifier or bcm proc directory is not
registered or created yet. Although this is a low probability scenario, it
is not impossible.
Move register_pernet_subsys() and register_netdevice_notifier() to the
front of can_proto_register(). In addition, register_pernet_subsys() and
register_netdevice_notifier() may fail, check their results are necessary.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/all/823cff0ebec33fa9389eeaf8b8ded3217c32cb38.1663206163.git.william.xuanziyang@huawei.com
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Enable CAN_RAW sockets to read and write CAN XL frames analogue to the
CAN FD extension (new CAN_RAW_XL_FRAMES sockopt).
A CAN XL network interface is capable to handle Classical CAN, CAN FD and
CAN XL frames. When CAN_RAW_XL_FRAMES is enabled, the CAN_RAW socket checks
whether the addressed CAN network interface is capable to handle the
provided CAN frame.
In opposite to the fixed number of bytes for
- CAN frames (CAN_MTU = sizeof(struct can_frame))
- CAN FD frames (CANFD_MTU = sizeof(struct can_frame))
the number of bytes when reading/writing CAN XL frames depends on the
number of data bytes. For efficiency reasons the length of the struct
canxl_frame is truncated to the needed size for read/write operations.
This leads to a calculated size of CANXL_HDR_SIZE + canxl_frame::len which
is enforced on write() operations and guaranteed on read() operations.
NB: Valid length values are 1 .. 2048 (CANXL_MIN_DLEN .. CANXL_MAX_DLEN).
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20220912170725.120748-8-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
- add new ETH_P_CANXL ethernet protocol type
- update skb checks for CAN XL
- add alloc_canxl_skb() which now needs a data length parameter
- introduce init_can_skb_reserve() to reduce code duplication
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20220912170725.120748-6-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
To simplify the testing in user space all struct canfd_frame's provided by
the CAN subsystem of the Linux kernel now have the CANFD_FDF flag set in
canfd_frame::flags.
NB: Handcrafted ETH_P_CANFD frames introduced via PF_PACKET socket might
not set this bit correctly. During the check for sufficient headroom in
PF_PACKET sk_buffs the uninitialized CAN sk_buff data structures are filled.
In the case of a CAN FD frame the CANFD_FDF flag is set accordingly.
As the CAN frame content is already zero initialized in alloc_canfd_skb()
the obsolete initialization of cf->flags in the CTU CAN FD driver has been
removed as it would overwrite the already set CANFD_FDF flag.
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20220912170725.120748-4-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Replace open coded checks for sk_buffs containing Classical CAN and
CAN FD frame structures as a preparation for CAN XL support.
With the added length check the unintended processing of CAN XL frames
having the CANXL_XLF bit set can be suppressed even when the skb->len
fits to non CAN XL frames.
The CAN_RAW socket needs a rework to use these helpers. Therefore the
use of these helpers is postponed to the CAN_RAW CAN XL integration.
The J1939 protocol gets a check for Classical CAN frames too.
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/all/20220912170725.120748-2-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Now, register notifier after register proto successfully. It can create
raw socket and set socket options once register proto successfully, so it
is possible missing notifier event before register notifier successfully
although this is a low probability scenario.
Move notifier registration to the front of proto registration like done
in j1939. In addition, register_netdevice_notifier() may fail, check its
result is necessary.
Signed-off-by: Ziyang Xuan <william.xuanziyang@huawei.com>
Link: https://lore.kernel.org/all/7af9401f0d2d9fed36c1667b5ac9b8df8f8b87ee.1661584485.git.william.xuanziyang@huawei.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We need to drop skb references taken in j1939_session_skb_queue() when
destroying a session in j1939_session_destroy(). Otherwise those skbs
would be lost.
Link to Syzkaller info and repro: https://forge.ispras.ru/issues/11743.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
V1: https://lore.kernel.org/all/20220708175949.539064-1-pchelkin@ispras.ru
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Suggested-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20220805150216.66313-1-pchelkin@ispras.ru
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
We should warn user-space that it is doing something wrong when trying
to activate sessions with identical parameters but WARN_ON_ONCE macro
can not be used here as it serves a different purpose.
So it would be good to replace it with netdev_warn_once() message.
Found by Linux Verification Center (linuxtesting.org) with Syzkaller.
Fixes: 9d71dd0c70 ("can: add support of SAE J1939 protocol")
Signed-off-by: Fedor Pchelkin <pchelkin@ispras.ru>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Oleksij Rempel <o.rempel@pengutronix.de>
Link: https://lore.kernel.org/all/20220729143655.1108297-1-pchelkin@ispras.ru
[mkl: fix indention]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Fedor Pchelkin