When running ocfs2 test suite multiple nodes reflink stress test, for a
4 nodes cluster, every unlink() for refcounted file needs about 700s.
The slow unlink is caused by the contention of refcount tree lock since
all nodes are unlink files using the same refcount tree. When the
unlinking file have many extents(over 1600 in our test), most of the
extents has refcounted flag set. In ocfs2_commit_truncate(), it will
execute the following call trace for every extents. This means it needs
get and released refcount tree lock about 1600 times. And when several
nodes are do this at the same time, the performance will be very low.
ocfs2_remove_btree_range()
-- ocfs2_lock_refcount_tree()
---- ocfs2_refcount_lock()
------ __ocfs2_cluster_lock()
ocfs2_refcount_lock() is costly, move it to ocfs2_commit_truncate() to
do lock/unlock once can improve a lot performance.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Wengang <wen.gang.wang@oracle.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Filesize is not a good indication that the file needs to be synced.
An example where this breaks is:
1. Open the file in O_SYNC|O_RDWR
2. Read a small portion of the file (say 64 bytes)
3. Lseek to starting of the file
4. Write 64 bytes
If the node crashes, it is not written out to disk because this was not
committed in the journal and the other node which reads the file after
recovery reads stale data (even if the write on the other node was
successful)
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.de>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull UDF and quota updates from Jan Kara:
"A few UDF fixes and also a few patches which are preparing filesystems
for support of project quotas in VFS"
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
udf: Fix loading of special inodes
ocfs2: Back out change to use OCFS2_MAXQUOTAS in ocfs2_setattr()
udf: remove redundant sys_tz declaration
ocfs2: Don't use MAXQUOTAS value
reiserfs: Don't use MAXQUOTAS value
ext3: Don't use MAXQUOTAS value
udf: Fix race between write(2) and close(2)
For commit ocfs2 journal, ocfs2 journal thread will acquire the mutex
osb->journal->j_trans_barrier and wake up jbd2 commit thread, then it
will wait until jbd2 commit thread done. In order journal mode, jbd2
needs flushing dirty data pages first, and this needs get page lock.
So osb->journal->j_trans_barrier should be got before page lock.
But ocfs2_write_zero_page() and ocfs2_write_begin_inline() obey this
locking order, and this will cause deadlock and hung the whole cluster.
One deadlock catched is the following:
PID: 13449 TASK: ffff8802e2f08180 CPU: 31 COMMAND: "oracle"
#0 [ffff8802ee3f79b0] __schedule at ffffffff8150a524
#1 [ffff8802ee3f7a58] schedule at ffffffff8150acbf
#2 [ffff8802ee3f7a68] rwsem_down_failed_common at ffffffff8150cb85
#3 [ffff8802ee3f7ad8] rwsem_down_read_failed at ffffffff8150cc55
#4 [ffff8802ee3f7ae8] call_rwsem_down_read_failed at ffffffff812617a4
#5 [ffff8802ee3f7b50] ocfs2_start_trans at ffffffffa0498919 [ocfs2]
#6 [ffff8802ee3f7ba0] ocfs2_zero_start_ordered_transaction at ffffffffa048b2b8 [ocfs2]
#7 [ffff8802ee3f7bf0] ocfs2_write_zero_page at ffffffffa048e9bd [ocfs2]
#8 [ffff8802ee3f7c80] ocfs2_zero_extend_range at ffffffffa048ec83 [ocfs2]
#9 [ffff8802ee3f7ce0] ocfs2_zero_extend at ffffffffa048edfd [ocfs2]
#10 [ffff8802ee3f7d50] ocfs2_extend_file at ffffffffa049079e [ocfs2]
#11 [ffff8802ee3f7da0] ocfs2_setattr at ffffffffa04910ed [ocfs2]
#12 [ffff8802ee3f7e70] notify_change at ffffffff81187d29
#13 [ffff8802ee3f7ee0] do_truncate at ffffffff8116bbc1
#14 [ffff8802ee3f7f50] sys_ftruncate at ffffffff8116bcbd
#15 [ffff8802ee3f7f80] system_call_fastpath at ffffffff81515142
RIP: 00007f8de750c6f7 RSP: 00007fffe786e478 RFLAGS: 00000206
RAX: 000000000000004d RBX: ffffffff81515142 RCX: 0000000000000000
RDX: 0000000000000200 RSI: 0000000000028400 RDI: 000000000000000d
RBP: 00007fffe786e040 R8: 0000000000000000 R9: 000000000000000d
R10: 0000000000000000 R11: 0000000000000206 R12: 000000000000000d
R13: 00007fffe786e710 R14: 00007f8de70f8340 R15: 0000000000028400
ORIG_RAX: 000000000000004d CS: 0033 SS: 002b
crash64> bt
PID: 7610 TASK: ffff88100fd56140 CPU: 1 COMMAND: "ocfs2cmt"
#0 [ffff88100f4d1c50] __schedule at ffffffff8150a524
#1 [ffff88100f4d1cf8] schedule at ffffffff8150acbf
#2 [ffff88100f4d1d08] jbd2_log_wait_commit at ffffffffa01274fd [jbd2]
#3 [ffff88100f4d1d98] jbd2_journal_flush at ffffffffa01280b4 [jbd2]
#4 [ffff88100f4d1dd8] ocfs2_commit_cache at ffffffffa0499b14 [ocfs2]
#5 [ffff88100f4d1e38] ocfs2_commit_thread at ffffffffa0499d38 [ocfs2]
#6 [ffff88100f4d1ee8] kthread at ffffffff81090db6
#7 [ffff88100f4d1f48] kernel_thread_helper at ffffffff81516284
crash64> bt
PID: 7609 TASK: ffff88100f2d4480 CPU: 0 COMMAND: "jbd2/dm-20-86"
#0 [ffff88100def3920] __schedule at ffffffff8150a524
#1 [ffff88100def39c8] schedule at ffffffff8150acbf
#2 [ffff88100def39d8] io_schedule at ffffffff8150ad6c
#3 [ffff88100def39f8] sleep_on_page at ffffffff8111069e
#4 [ffff88100def3a08] __wait_on_bit_lock at ffffffff8150b30a
#5 [ffff88100def3a58] __lock_page at ffffffff81110687
#6 [ffff88100def3ab8] write_cache_pages at ffffffff8111b752
#7 [ffff88100def3be8] generic_writepages at ffffffff8111b901
#8 [ffff88100def3c48] journal_submit_data_buffers at ffffffffa0120f67 [jbd2]
#9 [ffff88100def3cf8] jbd2_journal_commit_transaction at ffffffffa0121372[jbd2]
#10 [ffff88100def3e68] kjournald2 at ffffffffa0127a86 [jbd2]
#11 [ffff88100def3ee8] kthread at ffffffff81090db6
#12 [ffff88100def3f48] kernel_thread_helper at ffffffff81516284
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Alex Chen <alex.chen@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ocfs2_setattr() actually needs to really use MAXQUOTAS and not
OCFS2_MAXQUOTAS since it will pass the array over to VFS. Currently
this isn't a problem since MAXQUOTAS == OCFS2_MAXQUOTAS but it would
be once we introduce project quotas.
CC: Mark Fasheh <mfasheh@suse.com>
CC: Joel Becker <jlbec@evilplan.org>
CC: ocfs2-devel@oss.oracle.com
Signed-off-by: Jan Kara <jack@suse.cz>
MAXQUOTAS value defines maximum number of quota types VFS supports.
This isn't necessarily the number of types ocfs2 supports and with
addition of project quotas these two numbers stop matching. So make
ocfs2 use its private definition.
CC: Mark Fasheh <mfasheh@suse.com>
CC: Joel Becker <jlbec@evilplan.org>
CC: ocfs2-devel@oss.oracle.com
Signed-off-by: Jan Kara <jack@suse.cz>
Pull vfs updates from Al Viro:
"This the bunch that sat in -next + lock_parent() fix. This is the
minimal set; there's more pending stuff.
In particular, I really hope to get acct.c fixes merged this cycle -
we need that to deal sanely with delayed-mntput stuff. In the next
pile, hopefully - that series is fairly short and localized
(kernel/acct.c, fs/super.c and fs/namespace.c). In this pile: more
iov_iter work. Most of prereqs for ->splice_write with sane locking
order are there and Kent's dio rewrite would also fit nicely on top of
this pile"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (70 commits)
lock_parent: don't step on stale ->d_parent of all-but-freed one
kill generic_file_splice_write()
ceph: switch to iter_file_splice_write()
shmem: switch to iter_file_splice_write()
nfs: switch to iter_splice_write_file()
fs/splice.c: remove unneeded exports
ocfs2: switch to iter_file_splice_write()
->splice_write() via ->write_iter()
bio_vec-backed iov_iter
optimize copy_page_{to,from}_iter()
bury generic_file_aio_{read,write}
lustre: get rid of messing with iovecs
ceph: switch to ->write_iter()
ceph_sync_direct_write: stop poking into iov_iter guts
ceph_sync_read: stop poking into iov_iter guts
new helper: copy_page_from_iter()
fuse: switch to ->write_iter()
btrfs: switch to ->write_iter()
ocfs2: switch to ->write_iter()
xfs: switch to ->write_iter()
...
The last in-tree caller of block_write_full_page_endio() was removed in
January 2013. It's time to remove the EXPORT_SYMBOL, which leaves
block_write_full_page() as the only caller of
block_write_full_page_endio(), so inline block_write_full_page_endio()
into block_write_full_page().
Signed-off-by: Matthew Wilcox <matthew.r.wilcox@intel.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Dave Chinner <david@fromorbit.com>
Cc: Dheeraj Reddy <dheeraj.reddy@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Now It Can Be Done(tm) - we don't need to do iov_shorten() in
generic_file_direct_write() anymore, now that all ->direct_IO()
instances are converted to proper iov_iter methods and honour
iter->count and iter->iov_offset properly.
Get rid of count/ocount arguments of generic_file_direct_write(),
while we are at it.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
For now, just use the same thing we pass to ->direct_IO() - it's all
iovec-based at the moment. Pass it explicitly to iov_iter_init() and
account for kvec vs. iovec in there, by the same kludge NFS ->direct_IO()
uses.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
all callers of ->aio_read() and ->aio_write() have iov/nr_segs already
checked - generic_segment_checks() done after that is just an odd way
to spell iov_length().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Pull vfs updates from Al Viro:
"The first vfs pile, with deep apologies for being very late in this
window.
Assorted cleanups and fixes, plus a large preparatory part of iov_iter
work. There's a lot more of that, but it'll probably go into the next
merge window - it *does* shape up nicely, removes a lot of
boilerplate, gets rid of locking inconsistencie between aio_write and
splice_write and I hope to get Kent's direct-io rewrite merged into
the same queue, but some of the stuff after this point is having
(mostly trivial) conflicts with the things already merged into
mainline and with some I want more testing.
This one passes LTP and xfstests without regressions, in addition to
usual beating. BTW, readahead02 in ltp syscalls testsuite has started
giving failures since "mm/readahead.c: fix readahead failure for
memoryless NUMA nodes and limit readahead pages" - might be a false
positive, might be a real regression..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (63 commits)
missing bits of "splice: fix racy pipe->buffers uses"
cifs: fix the race in cifs_writev()
ceph_sync_{,direct_}write: fix an oops on ceph_osdc_new_request() failure
kill generic_file_buffered_write()
ocfs2_file_aio_write(): switch to generic_perform_write()
ceph_aio_write(): switch to generic_perform_write()
xfs_file_buffered_aio_write(): switch to generic_perform_write()
export generic_perform_write(), start getting rid of generic_file_buffer_write()
generic_file_direct_write(): get rid of ppos argument
btrfs_file_aio_write(): get rid of ppos
kill the 5th argument of generic_file_buffered_write()
kill the 4th argument of __generic_file_aio_write()
lustre: don't open-code kernel_recvmsg()
ocfs2: don't open-code kernel_recvmsg()
drbd: don't open-code kernel_recvmsg()
constify blk_rq_map_user_iov() and friends
lustre: switch to kernel_sendmsg()
ocfs2: don't open-code kernel_sendmsg()
take iov_iter stuff to mm/iov_iter.c
process_vm_access: tidy up a bit
...
Ensure that ocfs2_update_inode_fsync_trans() is called any time we touch
an inode in a given transaction. This is a follow-on to the previous
patch to reduce lock contention and deadlocking during an fsync
operation.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Wengang <wen.gang.wang@oracle.com>
Cc: Greg Marsden <greg.marsden@oracle.com>
Cc: Srinivas Eeda <srinivas.eeda@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
llseek requires ocfs2 inode lock for updating the file size in SEEK_END.
because the file size maybe update on another node.
This bug can be reproduce the following scenario: at first, we dd a test
fileA, the file size is 10k.
on NodeA:
---------
1) open the test fileA, lseek the end of file. and print the position.
2) close the test fileA
on NodeB:
1) open the test fileA, append the 5k data to test FileA.
2) lseek the end of file. and print the position.
3) close file.
At first we run the test program1 on NodeA , the result is 10k. And
then run the test program2 on NodeB, the result is 15k. At last, we run
the test program1 on NodeA again, the result is 10k.
After applying this patch the three step result is 15k.
test result: 1000000 times lseek call;
index lseek with inode lock (unit:us) lseek without inode lock (unit:us)
1 1168162 555383
2 1168011 549504
3 1170538 549396
4 1170375 551685
5 1170444 556719
6 1174364 555307
7 1163294 551552
8 1170080 549350
9 1162464 553700
10 1165441 552594
avg 1168317 552519
avg with lock - avg without lock = 615798
(avg with lock - avg without lock)/1000000=0.615798 us
Signed-off-by: Jensen <shencanquan@huawei.com>
Cc: Jie Liu <jeff.liu@oracle.com>
Acked-by: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Sunil Mushran <sunil.mushran@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, ocfs2_sync_file grabs i_mutex and forces the current journal
transaction to complete. This isn't terribly efficient, since sync_file
really only needs to wait for the last transaction involving that inode
to complete, and this doesn't require i_mutex.
Therefore, implement the necessary bits to track the newest tid
associated with an inode, and teach sync_file to wait for that instead
of waiting for everything in the journal to commit. Furthermore, only
issue the flush request to the drive if jbd2 hasn't already done so.
This also eliminates the deadlock between ocfs2_file_aio_write() and
ocfs2_sync_file(). aio_write takes i_mutex then calls
ocfs2_aiodio_wait() to wait for unaligned dio writes to finish.
However, if that dio completion involves calling fsync, then we can get
into trouble when some ocfs2_sync_file tries to take i_mutex.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is a problem that waitqueue_active() may check stale data thus miss
a wakeup of threads waiting on ip_unaligned_aio.
The valid value of ip_unaligned_aio is only 0 and 1 so we can change it to
be of type mutex thus the above prolem is avoid. Another benifit is that
mutex which works as FIFO is fairer than wake_up_all().
Signed-off-by: Wengang Wang <wen.gang.wang@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
fs-writeback will release the dirty pages without page lock whose offset
are over inode size, the release happens at
block_write_full_page_endio(). If not update, dirty pages in file holes
may be released before flushed to the disk, then file holes will contain
some non-zero data, this will cause sparse file md5sum error.
To reproduce the bug, find a big sparse file with many holes, like vm
image file, its actual size should be bigger than available mem size to
make writeback work more frequently, tar it with -S option, then keep
untar it and check its md5sum again and again until you get a wrong
md5sum.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Younger Liu <younger.liu@huawei.com>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The issue scenario is as following:
- Create a small file and fallocate a large disk space for a file with
FALLOC_FL_KEEP_SIZE option.
- ftruncate the file back to the original size again. but the disk free
space is not changed back. This is a real bug that be fixed in this
patch.
In order to solve the issue above, we modified ocfs2_setattr(), if
attr->ia_size != i_size_read(inode), It calls ocfs2_truncate_file(), and
truncate disk space to attr->ia_size.
Signed-off-by: Younger Liu <younger.liu@huawei.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Tested-by: Jie Liu <jeff.liu@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Reviewed-by: Mark Fasheh <mfasheh@suse.de>
Cc: Sunil Mushran <sunil.mushran@gmail.com>
Reviewed-by: Jensen <shencanquan@huawei.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If filesystem is readonly, there is no need to flush drive's caches or
force any uncommitted transactions.
[akpm@linux-foundation.org: return -EROFS, not 0]
Signed-off-by: Younger Liu <younger.liucn@gmail.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs updates from Al Viro:
"Assorted stuff; the biggest pile here is Christoph's ACL series. Plus
assorted cleanups and fixes all over the place...
There will be another pile later this week"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (43 commits)
__dentry_path() fixes
vfs: Remove second variable named error in __dentry_path
vfs: Is mounted should be testing mnt_ns for NULL or error.
Fix race when checking i_size on direct i/o read
hfsplus: remove can_set_xattr
nfsd: use get_acl and ->set_acl
fs: remove generic_acl
nfs: use generic posix ACL infrastructure for v3 Posix ACLs
gfs2: use generic posix ACL infrastructure
jfs: use generic posix ACL infrastructure
xfs: use generic posix ACL infrastructure
reiserfs: use generic posix ACL infrastructure
ocfs2: use generic posix ACL infrastructure
jffs2: use generic posix ACL infrastructure
hfsplus: use generic posix ACL infrastructure
f2fs: use generic posix ACL infrastructure
ext2/3/4: use generic posix ACL infrastructure
btrfs: use generic posix ACL infrastructure
fs: make posix_acl_create more useful
fs: make posix_acl_chmod more useful
...
This contains some major refactoring for the create path so that
inodes are created with the right mode to start with instead of
fixing it up later.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
An unreserve space ioctl OCFS2_IOC_UNRESVSP/64 should reject a negative
length.
Orabug:14789508
Signed-off-by: Tariq Saseed <tariq.x.saeed@oracle.com>
Signed-off-by: Srinivas Eeda <srinivas.eeda@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unwritten extent only exists for file systems which support holes. But
the comment said was opposite meaning and also the comment is not very
clear, so rephase it.
Signed-off-by: Junxiao Bi <junxiao.bi@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Code cleanup to remove unnecessary variable passed but never used
to ocfs2_calc_extend_credits.
Signed-off-by: Goldwyn Rodrigues <rgoldwyn@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull aio changes from Ben LaHaise:
"First off, sorry for this pull request being late in the merge window.
Al had raised a couple of concerns about 2 items in the series below.
I addressed the first issue (the race introduced by Gu's use of
mm_populate()), but he has not provided any further details on how he
wants to rework the anon_inode.c changes (which were sent out months
ago but have yet to be commented on).
The bulk of the changes have been sitting in the -next tree for a few
months, with all the issues raised being addressed"
* git://git.kvack.org/~bcrl/aio-next: (22 commits)
aio: rcu_read_lock protection for new rcu_dereference calls
aio: fix race in ring buffer page lookup introduced by page migration support
aio: fix rcu sparse warnings introduced by ioctx table lookup patch
aio: remove unnecessary debugging from aio_free_ring()
aio: table lookup: verify ctx pointer
staging/lustre: kiocb->ki_left is removed
aio: fix error handling and rcu usage in "convert the ioctx list to table lookup v3"
aio: be defensive to ensure request batching is non-zero instead of BUG_ON()
aio: convert the ioctx list to table lookup v3
aio: double aio_max_nr in calculations
aio: Kill ki_dtor
aio: Kill ki_users
aio: Kill unneeded kiocb members
aio: Kill aio_rw_vect_retry()
aio: Don't use ctx->tail unnecessarily
aio: io_cancel() no longer returns the io_event
aio: percpu ioctx refcount
aio: percpu reqs_available
aio: reqs_active -> reqs_available
aio: fix build when migration is disabled
...
In ocfs2_remove_inode_range(), there is a memory leak. The variable path
has allocated memory with ocfs2_new_path_from_et(), but it is not free.
Signed-off-by: Younger Liu <younger.liu@huawei.com>
Reviewed-by: Jie Liu <jeff.liu@oracle.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The issue scenario is as following:
When fallocating a very large disk space for a small file,
__ocfs2_extend_allocation attempts to get a very large transaction. For
some journal sizes, there may be not enough room for this transaction,
and the fallocate will fail.
The patch below extends & restarts the transaction as necessary while
allocating space, and should work with even the smallest journal. This
patch refers ext4 resize.
Test:
# mkfs.ocfs2 -b 4K -C 32K -T datafiles /dev/sdc
...(jounral size is 32M)
# mount.ocfs2 /dev/sdc /mnt/ocfs2/
# touch /mnt/ocfs2/1.log
# fallocate -o 0 -l 400G /mnt/ocfs2/1.log
fallocate: /mnt/ocfs2/1.log: fallocate failed: Cannot allocate memory
# tail -f /var/log/messages
[ 7372.278591] JBD: fallocate wants too many credits (2051 > 2048)
[ 7372.278597] (fallocate,6438,0):__ocfs2_extend_allocation:709 ERROR: status = -12
[ 7372.278603] (fallocate,6438,0):ocfs2_allocate_unwritten_extents:1504 ERROR: status = -12
[ 7372.278607] (fallocate,6438,0):__ocfs2_change_file_space:1955 ERROR: status = -12
^C
With this patch, the test works well.
Signed-off-by: Younger Liu <younger.liu@huawei.com>
Cc: Jie Liu <jeff.liu@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since ocfs2_cow_file_pos will invoke ocfs2_refcount_icow with a NULL as
the struct file pointer, it finally result in a null pointer dereference
in ocfs2_duplicate_clusters_by_page.
This patch replace file pointer with inode pointer in
cow_duplicate_clusters to fix this issue.
[jeff.liu@oracle.com: rebased patch against linux-next tree]
Signed-off-by: Tiger Yang <tiger.yang@oracle.com>
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Acked-by: Tao Ma <tm@tao.ma>
Tested-by: David Weber <wb@munzinger.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This code doesn't serve any purpose anymore, since the aio retry
infrastructure has been removed.
This change should be safe because aio_read/write are also used for
synchronous IO, and called from do_sync_read()/do_sync_write() - and
there's no looping done in the sync case (the read and write syscalls).
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Zach Brown <zab@redhat.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Jeff Moyer <jmoyer@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Benjamin LaHaise <bcrl@kvack.org>
Signed-off-by: Benjamin LaHaise <bcrl@kvack.org>
For those file systems(btrfs/ext4/ocfs2/tmpfs) that support
SEEK_DATA/SEEK_HOLE functions, we end up handling the similar
matter in lseek_execute() to update the current file offset
to the desired offset if it is valid, ceph also does the
simliar things at ceph_llseek().
To reduce the duplications, this patch make lseek_execute()
public accessible so that we can call it directly from the
underlying file systems.
Thanks Dave Chinner for this suggestion.
[AV: call it vfs_setpos(), don't bring the removed 'inode' argument back]
v2->v1:
- Add kernel-doc comments for lseek_execute()
- Call lseek_execute() in ceph->llseek()
Signed-off-by: Jie Liu <jeff.liu@oracle.com>
Cc: Dave Chinner <dchinner@redhat.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: Josef Bacik <jbacik@fusionio.com>
Cc: Ben Myers <bpm@sgi.com>
Cc: Ted Tso <tytso@mit.edu>
Cc: Hugh Dickins <hughd@google.com>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Sage Weil <sage@inktank.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
In ocfs2_file_aio_write(), it does ocfs2_rw_lock() first and then
ocfs2_inode_lock().
But if ocfs2_inode_lock() failed, it goes to out_sems without unlocking
rw lock. This will cause a bug in ocfs2_lock_res_free() when testing
res->l_ex_holders, which is increased in __ocfs2_cluster_lock() and
decreased in __ocfs2_cluster_unlock().
Signed-off-by: Joseph Qi <joseph.qi@huawei.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Li Zefan <lizefan@huawei.com>
Cc: "Duyongfeng (B)" <du.duyongfeng@huawei.com>
Acked-by: Sunil Mushran <sunil.mushran@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
But the kernel decided to call it "origin" instead. Fix most of the
sites.
Acked-by: Hugh Dickins <hughd@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There is no reason to pass the nr_pages_dirtied argument, because
nr_pages_dirtied value from the caller is unused in
balance_dirty_pages_ratelimited_nr().
Signed-off-by: Namjae Jeon <linkinjeon@gmail.com>
Signed-off-by: Vivek Trivedi <vtrivedi018@gmail.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Junxiao Bi