We currently initialize the group of private IRQs during
kvm_vgic_vcpu_init, and the value of the group depends on the GIC model
we are emulating. However, CPUs created before creating (and
initializing) the VGIC might end up with the wrong group if the VGIC
is created as GICv3 later.
Since we have no enforced ordering of creating the VGIC and creating
VCPUs, we can end up with part the VCPUs being properly intialized and
the remaining incorrectly initialized. That also means that we have no
single place to do the per-cpu data structure initialization which
depends on knowing the emulated GIC model (which is only the group
field).
This patch removes the incorrect comment from kvm_vgic_vcpu_init and
initializes the group of all previously created VCPUs's private
interrupts in vgic_init in addition to the existing initialization in
kvm_vgic_vcpu_init.
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Failing to properly reset system registers is pretty bad. But not
quite as bad as bringing the whole machine down... So warn loudly,
but slightly more gracefully.
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Acked-by: Christoffer Dall <christoffer.dall@arm.com>
The current kvm_psci_vcpu_on implementation will directly try to
manipulate the state of the VCPU to reset it. However, since this is
not done on the thread that runs the VCPU, we can end up in a strangely
corrupted state when the source and target VCPUs are running at the same
time.
Fix this by factoring out all reset logic from the PSCI implementation
and forwarding the required information along with a request to the
target VCPU.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
We have two ways to reset a vcpu:
- either through VCPU_INIT
- or through a PSCI_ON call
The first one is easy to reason about. The second one is implemented
in a more bizarre way, as it is the vcpu that handles PSCI_ON that
resets the vcpu that is being powered-on. As we need to turn the logic
around and have the target vcpu to reset itself, we must take some
preliminary steps.
Resetting the VCPU state modifies the system register state in memory,
but this may interact with vcpu_load/vcpu_put if running with preemption
disabled, which in turn may lead to corrupted system register state.
Address this by disabling preemption and doing put/load if required
around the reset logic.
Reviewed-by: Andrew Jones <drjones@redhat.com>
Signed-off-by: Christoffer Dall <christoffer.dall@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
There was a divergence between Linux and ACPICA on the definition of
ACPI_DEBUG_DEFAULT. This divergence was solved by taking ACPICA's
definition in 4c1379d7bb. After resolving the divergence, it was
clear that Linux users wanted to use their old set of debug flags.
This change fixes the divergence by setting these debug flags during
acpi_early_init() rather than during global variable initialization
in acpixf.h (owned by ACPICA).
Fixes: 4c1379d7bb ("ACPICA: Debug output: Add option to display method/object evaluation")
Reported-by: Michael J Ruhl <michael.j.ruhl@intel.com>
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com>
Signed-off-by: Erik Schmauss <erik.schmauss@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This reverts commit 9594ca6b87.
With the handle_simple_irq irq_flow_handler it must be ensured to
not call generic_handle_irq with the same IRQ number on 2 CPUs at
the same time (interrupts are floating on s390).
Contrary to my initial investigation the irq_desc's lock usage in
handle_simple_irq does not ensure this. Thus re-introduce the bit-
lock usage in s390's pci handler.
Reported-by: Ursula Braun <ubraun@linux.ibm.com>
Reported-by: Alexander Schmidt <alexs@linux.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
A collection of a few small fixes. The most significant one is the
fix for the possible race at loading HD-audio drivers. This has been
present for long time and surfaced only in a rare occasion, but
finally spotted out.
The rest are usual device-specific fixes for HD-audio and USB-audio.
-----BEGIN PGP SIGNATURE-----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=aD7u
-----END PGP SIGNATURE-----
Merge tag 'sound-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
"A collection of a few small fixes.
The most significant one is the fix for the possible race at loading
HD-audio drivers. This has been present for long time and surfaced
only in a rare occasion, but finally spotted out"
* tag 'sound-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/ca0132 - Fix build error without CONFIG_PCI
ALSA: compress: Fix stop handling on compressed capture streams
ALSA: usb-audio: Add support for new T+A USB DAC
ALSA: hda - Serialize codec registrations
ALSA: hda/realtek - Use a common helper for hp pin reference
ALSA: hda/realtek - Fix lose hp_pins for disable auto mute
ALSA: hda/realtek - Headset microphone support for System76 darp5
A small fix for a uapi header, and a fix for VDPA for non-x86 guests.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
-----BEGIN PGP SIGNATURE-----
iQEcBAABAgAGBQJcWfKsAAoJECgfDbjSjVRpz8AIALAFWg40sy8n1LjcDoTar9oP
YRrKUD7ag4dL8I41kbu4Vk8GQG1cSKFxk+PnZ4lhyiJGUgcd267qoUf3Kk9MxL94
IvMxa/Y2qPiSpEIwJGDxikJNaqcSDTJXYgs6zjCLHgo35WUbmAxVh3iZDWkpaKKl
mql+DsotNhEYE5BGAi8OhPIbGOtumkhCy6JySBD+trHyivKIotKaPN6PoNudPRQU
ipP1YlTZQL2vYp3vwbwjaO4IKo/17IDQtzHxLQU2Q1ZORSPOctjffmF74qfDkNKl
pqWYXwVbq8/EuKyhNexAqU3vkSQaLUEMthzi5d/Z7QYeJt/K5xcpgkKHYm1lZ/U=
=XTXV
-----END PGP SIGNATURE-----
Merge tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost
Pull virtio fixes from Michael Tsirkin:
"A small fix for a uapi header, and a fix for VDPA for non-x86 guests"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
virtio: drop internal struct from UAPI
virtio: support VIRTIO_F_ORDER_PLATFORM
- Cut and paste fix to have uprobe printks say "uprobe" and not "kprobe"
- Add terminating '\0' byte when copying of function arguments
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXFsNwBQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qlSLAP9iup0t8BrDYcJQCNIJK+7hwBdB642c
11qbWE7aXfsyUwEAu78tJfQfmBeZz7mHxKeMkTHQHE2IqV5qU311twOFiAE=
=zkXr
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
"This has two fixes for uprobe code.
- Cut and paste fix to have uprobe printks say "uprobe" and not
"kprobe"
- Add terminating '\0' byte when copying function arguments"
* tag 'trace-v5.0-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
tracing/uprobes: Fix output for multiple string arguments
tracing: uprobes: Fix typo in pr_fmt string
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQSQHSd0lITzzeNWNm3h3BK/laaZPAUCXFls+wAKCRDh3BK/laaZ
PC+hAQDRkyJeAmMzpHwvv/IASqpJgc6HrSzH0p201lDyARcKIAD+MWxZHYP4ltAn
WVTLIvYT1xsoqGG3plfZ/d1iNbAWcwU=
=cL/O
-----END PGP SIGNATURE-----
Merge tag 'fuse-fixes-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse
Pull fuse fixes from Miklos Szeredi:
"A fix for a CUSE regression introduced in v4.20, as well as fixes for
a couple of old bugs"
* tag 'fuse-fixes-5.0-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: decrement NR_WRITEBACK_TEMP on the right page
fuse: call pipe_buf_release() under pipe lock
cuse: fix ioctl
fuse: handle zero sized retrieve correctly
8c56df372b ("net: add support for Cavium PTP coprocessor") added the
Cavium PTP coprocessor driver and enabled it by default. Remove the
"default y" because the driver only applies to Cavium ThunderX processors.
Fixes: 8c56df372b ("net: add support for Cavium PTP coprocessor")
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in sbdma_tx_process() when
skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in velocity_free_tx_buf()
when skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in bdx_tx_cleanup() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called when skb xmit done. It makes
drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in hdlc_tx_done() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in mpc52xx_fec_tx_interrupt()
when skb xmit done. It makes drop profiles(dropwatch, perf) more
friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in epic_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in dscc4_tx_irq() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in de_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb_irq() should be called in dfx_xmt_done() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Reviewed-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In some case, we may use multiple pedit actions to modify packets.
The command shown as below: the last pedit action is effective.
$ tc filter add dev netdev_rep parent ffff: protocol ip prio 1 \
flower skip_sw ip_proto icmp dst_ip 3.3.3.3 \
action pedit ex munge ip dst set 192.168.1.100 pipe \
action pedit ex munge eth src set 00:00:00:00:00:01 pipe \
action pedit ex munge eth dst set 00:00:00:00:00:02 pipe \
action csum ip pipe \
action tunnel_key set src_ip 1.1.1.100 dst_ip 1.1.1.200 dst_port 4789 id 100 \
action mirred egress redirect dev vxlan0
To fix it, we add max_mod_hdr_actions to mlx5e_tc_flow_parse_attr struction,
max_mod_hdr_actions will store the max pedit action number we support and
num_mod_hdr_actions indicates how many pedit action we used, and store all
pedit action to mod_hdr_actions.
Fixes: d79b6df6b1 ("net/mlx5e: Add parsing of TC pedit actions to HW format")
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we offload tc filters to hardware, hardware flows can
be updated when mac of encap destination ip is changed.
But we ignore one case, that the mac of local encap ip can
be changed too, so we should also update them.
To fix it, add route_dev in mlx5e_encap_entry struct to save
the local encap netdevice, and when mac changed, kernel will
flush all the neighbour on the netdevice and send NETEVENT_NEIGH_UPDATE
event. The mlx5 driver will delete the flows and add them when neighbour
available again.
Fixes: 232c001398 ("net/mlx5e: Add support to neighbour update flow")
Cc: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Manish Chopra says:
====================
qed*: Bug fixes.
This series contains general qed/qede fixes.
Please consider applying this to "net"
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Version update for qed/qede modules.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix unnecessary logging of message in an expected
default case where coalescing value read (via ethtool -c)
migh not be valid unless they are configured explicitly
in the hardware using ethtool -C.
Signed-off-by: Rahul Verma <rverma@marvell.com>
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Under heavy traffic load, when changing number of channels via
ethtool (ethtool -L) which will cause interface to be reloaded,
it was observed that some packets gets transmitted on old TX
channel/queue id which doesn't really exist after the channel
configuration leads to system crash.
Add a safeguard in the driver by validating queue id through
ndo_select_queue() which is called before the ndo_start_xmit().
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Max supported queues is derived incorrectly in the case of multi-CoS.
Need to consider TCs while calculating num_queues for PF.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the case of Unified Fabric Port (UFP) mode, switch provides
the traffic class (TC) value to be used for the traffic.
Configure hardware to use this TC value for vlan priority.
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When slowpath messages are sent with high rate, the resulting
events can lead to a FW assert in case they are not handled fast
enough (Event Queue Full assert). Attempt to send queued slowpath
messages only after the newly evacuated entries in the EQ ring
are indicated to FW.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A patch set from Christoph for vmwgfx dma mode detection breakage with the
new dma code restructuring in 5.0
A couple of fixes also CC'd stable
Finally an improved IOMMU detection that automatically enables dma mapping
also with other vIOMMUS than the intel one if present and enabled.
Currently trying to start a VM in that case would fail catastrophically.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Hellstrom <thellstrom@vmware.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190206194735.4663-1-thellstrom@vmware.com
There are at least four different parts with the same Vendor and Device
ID ([16c3:abcd]):
1) Synopsys HAPS USB3 controller
2) Synopsys PCIe Root Port in Freescale/NXP i.MX6Q (reported by Lucas)
3) Synopsys PCIe Root Port in Freescale/NXP i.MX6QP (reported by Lukas)
4) Synopsys PCIe Root Port in Freescale/NXP i.MX7D (reported by Trent)
The HAPS USB3 controller has a Class Code of PCI_CLASS_SERIAL_USB_XHCI,
which means the XHCI driver would normally claim it. Previously,
quirk_synopsys_haps() changed the Class Code of all [16c3:abcd] devices,
including the Root Ports, to PCI_CLASS_SERIAL_USB_DEVICE to prevent the
XHCI driver from claiming them so dwc3-haps can claim them instead.
Changing the Class Code of the Root Ports prevents the PCI core from
handling them as bridges, so devices below them don't work.
Restrict the quirk so it only changes the Class Code for devices that start
with the PCI_CLASS_SERIAL_USB_XHCI Class Code, leaving the Root Ports
alone.
Fixes: 03e6742584 ("PCI: Override Synopsys USB 3.x HAPS device class")
Reported-by: Lukas F. Hartmann <lukas@mntmn.com>
Reported-by: Trent Piepho <tpiepho@impinj.com>
Reported-by: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
[bhelgaas: changelog]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
bio_trim() has an early return, which makes it _not_ idempotent, if the
offset is 0 and the bio's bi_size already matches the requested size.
Prior to DM, all users of bio_trim() were fine with this. But DM has
exposed the fact that bio_trim()'s early return is incompatible with a
cloned bio whose integrity payload must be trimmed via
bio_integrity_trim().
Fix this by reverting DM back to doing the equivalent of bio_trim() but
in an idempotent manner (so bio_integrity_trim is always performed).
Follow-on work is needed to assess what benefit bio_trim()'s early
return is providing to its existing callers.
Reported-by: Milan Broz <gmazyland@gmail.com>
Fixes: 57c36519e4 ("dm: fix clone_bio() to trigger blk_recount_segments()")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Block core changes to switch bio-based IO accounting to be percpu had a
side-effect of altering DM core to now rely on calling waitqueue_active
(in both bio-based and request-based) to check if another task is in
dm_wait_for_completion().
A memory barrier is needed before calling waitqueue_active(). DM core
doesn't piggyback on a preceding memory barrier so it must explicitly
use its own.
For more details on why using waitqueue_active() without a preceding
barrier is unsafe, please see the comment before the waitqueue_active()
definition in include/linux/wait.h.
Add the missing memory barrier by switching to using wq_has_sleeper().
Fixes: 6f75723190 ("dm: remove the pending IO accounting")
Fixes: c4576aed8d ("dm: fix request-based dm's use of dm_wait_for_completion")
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This function can't succeed if dp->pl is NULL. It will Oops inside the
call to return phylink_ethtool_get_eee(dp->pl, e);
Fixes: 1be52e97ed ("dsa: slave: eee: Allow ports to use phylink")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two and a half years ago, the client was changed to use gathered
Send for larger inline messages, in commit 655fec6987 ("xprtrdma:
Use gathered Send for large inline messages"). Several fixes were
required because there are a few in-kernel device drivers whose
max_sge is 3, and these were broken by the change.
Apparently my memory is going, because some time later, I submitted
commit 25fd86eca1 ("svcrdma: Don't overrun the SGE array in
svc_rdma_send_ctxt"), and after that, commit f3c1fd0ee2 ("svcrdma:
Reduce max_send_sges"). These too incorrectly assumed in-kernel
device drivers would have more than a few Send SGEs available.
The fix for the server side is not the same. This is because the
fundamental problem on the server is that, whether or not the client
has provisioned a chunk for the RPC reply, the server must squeeze
even the most complex RPC replies into a single RDMA Send. Failing
in the send path because of Send SGE exhaustion should never be an
option.
Therefore, instead of failing when the send path runs out of SGEs,
switch to using a bounce buffer mechanism to handle RPC replies that
are too complex for the device to send directly. That allows us to
remove the max_sge check to enable drivers with small max_sge to
work again.
Reported-by: Don Dutile <ddutile@redhat.com>
Fixes: 25fd86eca1 ("svcrdma: Don't overrun the SGE array in ...")
Cc: stable@vger.kernel.org
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
If the parameter 'count' is non-zero, nfsd4_clone_file_range() will
currently clobber all errors returned by vfs_clone_file_range() and
replace them with EINVAL.
Fixes: 42ec3d4c02 ("vfs: make remap_file_range functions take and...")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v4.20+
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
When something let __find_get_block_slow() hit all_mapped path, it calls
printk() for 100+ times per a second. But there is no need to print same
message with such high frequency; it is just asking for stall warning, or
at least bloating log files.
[ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8
[ 399.873324][T15342] b_state=0x00000029, b_size=512
[ 399.878403][T15342] device loop0 blocksize: 4096
[ 399.883296][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8
[ 399.890400][T15342] b_state=0x00000029, b_size=512
[ 399.895595][T15342] device loop0 blocksize: 4096
[ 399.900556][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8
[ 399.907471][T15342] b_state=0x00000029, b_size=512
[ 399.912506][T15342] device loop0 blocksize: 4096
This patch reduces frequency to up to once per a second, in addition to
concatenating three lines into one.
[ 399.866302][T15342] __find_get_block_slow() failed. block=1, b_blocknr=8, b_state=0x00000029, b_size=512, device loop0 blocksize: 4096
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Reviewed-by: Jan Kara <jack@suse.cz>
Cc: Dmitry Vyukov <dvyukov@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Add maintainer entry for SFF/SFP/SFP+ support.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
When calling register_blkdev() with specified major
device number, the return code is 0 on success.
So it seems not correct direct assign return code to
variable major_num in this case.
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Chengguang Xu <cgxu519@gmx.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
We've received a bugreport that using LPM with a SAMSUNG
MZ7TE512HMHP-000L1 SSD leads to system instability, we already have
a quirk for the MZ7TD256HAFV-000L9, which is also a Samsun EVO 840 /
PM851 OEM model, so it seems some of these models have a LPM issue.
This commits adds a NOLPM quirk for the model string from the new
bugeport, to avoid the reported stability issues.
Cc: stable@vger.kernel.org
BugLink: https://bugzilla.redhat.com/show_bug.cgi?id=1571330
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
RDMSR in the trampoline code overwrites EDX but that register is used
to indicate whether 5-level paging has to be enabled and if clobbered,
leads to failure to boot on a 5-level paging machine.
Preserve EDX on the stack while we are dealing with EFER.
Fixes: b677dfae5a ("x86/boot/compressed/64: Set EFER.LME=1 in 32-bit trampoline before returning to long mode")
Reported-by: Kyle D Pelton <kyle.d.pelton@intel.com>
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: dave.hansen@linux.intel.com
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Huang <wei@redhat.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190206115253.1907-1-kirill.shutemov@linux.intel.com
commit 4d230d1271 ("ASoC: rsnd: fixup not to call clk_get/set
under non-atomic") added new rsnd_ssi_prepare() and moved
rsnd_ssi_master_clk_start() to .prepare.
But, ssi user count (= ssi->usrcnt) is incremented at .init
(= rsnd_ssi_init()).
Because of these timing exchange, ssi->usrcnt check at
rsnd_ssi_master_clk_start() should be adjusted.
Otherwise, 2nd master clock setup will be no check.
This patch fixup this issue.
Fixes: commit 4d230d1271 ("ASoC: rsnd: fixup not to call clk_get/set under non-atomic")
Reported-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Reported-by: Valentine Barshak <valentine.barshak@cogentembedded.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Yusuke Goda <yusuke.goda.sx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
KASAN reports and additional traces point to out-of-bounds accesses to
the dapm_up_seq and dapm_down_seq lookup tables. The indices used are
larger than the array definition.
Fix by adding missing entries for the new widget types in these two
lookup tables, and align them with PGA values.
Also the sequences for the following widgets were not defined. Since
their values defaulted to zero, assign them explicitly
snd_soc_dapm_input
snd_soc_dapm_output
snd_soc_dapm_vmid
snd_soc_dapm_siggen
snd_soc_dapm_sink
Fixes: 8a70b4544e ('ASoC: dapm: Add new widget type for constructing DAPM graphs on DSPs.').
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Pull NVMe fixes from Christoph for this release.
* 'nvme-5.0' of git://git.infradead.org/nvme:
nvme-pci: fix rapid add remove sequence
nvme: lock NS list changes while handling command effects
A surprise removal may fail to tear down request queues if it is racing
with the initial asynchronous probe. If that happens, the remove path
won't see the queue resources to tear down, and the controller reset
path may create a new request queue on a removed device, but will not
be able to make forward progress, deadlocking the pci removal.
Protect setting up non-blocking resources from a shutdown by holding the
same mutex, and transition to the CONNECTING state after these resources
are initialized so the probe path may see the dead controller state
before dispatching new IO.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=202081
Reported-by: Alex Gagniuc <Alex_Gagniuc@Dellteam.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Tested-by: Alex Gagniuc <mr.nuke.me@gmail.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Christoffer Dall