Fix the following coccicheck warning:
./drivers/power/supply/cpcap-charger.c:416:31-36: WARNING: conversion to
bool not needed here
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Yang Li <yang.lee@linux.alibaba.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Adds 80000 us sleep when the usb cable is plugged in to hopefully avoid
bouncing contacts.
Upon pluging in the usb cable vbus will bounce for some time, causing cpcap to
dissconnect charging due to detecting an undervoltage condition. This is a
scope of vbus on xt894 while quickly inserting the usb cable with firm force,
probed at the far side of the usb socket and vbus loaded with approx 1k:
http://uvos.xyz/maserati/usbplug.jpg.
As can clearly be seen, vbus is all over the place for the first 15 ms or so
with a small blip at ~40 ms this causes the cpcap to trip up and disable
charging again.
The delay helps cpcap_usb_detect avoid the worst of this. It is, however, still
not ideal as strong vibrations can cause the issue to reapear any time during
charging. I have however not been able to cause the device to stop charging due
to this in practice as it is hard to vibrate the device such that the vbus pins
start bouncing again but cpcap_usb_detect is not called again due to a detected
disconnect/reconnect event.
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Signed-off-by: Carl Philipp Klemm <philipp@uvos.xyz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Currently if the pointer battery is null there is a null pointer
dereference on the call to power_supply_put. Fix this by only
performing the put if battery is not null.
Addresses-Coverity: ("Dereference after null check")
Fixes: 4bff91bb32 ("power: supply: cpcap-charger: Fix missing power_supply_put()")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We want to have the battery update it's status when the charge is done,
and when the charger is disconnected. Otherwise the battery does not know
when it's full unless there's a userspace app polling the battery status.
To do this, we add supplied_to handling to cpcap-battery, and implement
power_supply_changed() for cpcap-charger. When cpcap-charger calls
power_supply_changed(), cpcap-battery will update it's status.
Let's also use new_state variable for the POWER_SUPPLY_STATUS_CHARGING
case to have unified handling for the switch.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Let's turn cpcap_charger_set_state() into separate cpcap_charger_enable()
and cpcap_charger_disable() to simplify things, and to allow managing
status separately. This can be then used for the follow-up patches to
make battery full status behave a bit nicer.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We currently have both state and status, get rid of state and use
generic status instead.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Droid 4 has same problem as N900: it is often necessary to manually
tweak current draw from USB, for example when using thin charging cable.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
[tony@atomide.com: rebased, cleaned up whitespace issues, updated comments]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Just get rid of the custom enumeration if favor of the standard one.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
This should be only shown when debug is enabled.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
If we have a USB charger connected, reboot is flakey and often fails to
reboot the device with the charger LED staying on.
Let's fix this by implementing .shutdown.
Cc: Arthur Demchenkov <spinal.by@gmail.com>
Cc: Carl Philipp Klemm <philipp@uvos.xyz>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Commit 25d76fed7f ("phy: cpcap-usb: Use IRQF_ONESHOT") started causing
errors loading phy-cpcap-usb driver:
cpcap_battery cpcap_battery.0: failed to register power supply
genirq: Flags mismatch irq 211. 00002080 (se0conn) vs. 00000080 (se0conn)
cpcap-usb-phy cpcap-usb-phy.0: could not get irq se0conn: -16
Let's fix this by adding the missing IRQF_ONESHOT to also cpcap-battery
and cpcap-charger drivers.
Fixes: 25d76fed7f ("phy: cpcap-usb: Use IRQF_ONESHOT")
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Add 'static' keyword to internal function as reported by sparse
using the following configuration:
make ARCH=x86_64 allmodconfig
make C=1 CF='-fdiagnostic-prefix -D__CHECK_ENDIAN__'
Fixes: d4ee021c41 ("power: supply: cpcap-charger: Limit voltage to 4.2V for battery")
Signed-off-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Let's allow reconfiguring the cpcap-charger max charge voltage and
default to 4.2V that should be safe for the known users.
This allows the users to use 4.35V for the extra capacity if really
needed at a cost of probably shorter battery life. We check the
constant charge voltage limit set by the battery.
Some pieces of the property setting code is based on an earlier patch
from Pavel Machek <pavel@ucw.cz> but limited to configuring the charge
voltage for now.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We are currently using a wrong ADC range for the battery detection.
The ADC returns the battery temperature if connected.
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Pavel Machek <pavel@ucw.cz>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
There have been some cases of droid4 battery bulging that seem to be
related to being left connected to the charger for several weeks.
It is suspected that the 4.35V charge voltage configured for the battery
is too much in the long run, so lets limit the charge voltage to 4.2V.
It could also be that the batteries are just getting old.
We don't really want to just change the charge voltage to 4.2V as Android
may have charged the battery to 4.35V as pointed out by Pavel Machek.
To add checks for battery voltage, the driver needs to understand the
voltage it's charging at, and also needs to better understand it's
charger state. Right now it only understands connect and disconnect,
while now we need to know also a connected state but not charging.
So let's add better charger state handling with help of chrgcurr2 interrupt
for detecting charge full and retry, and add a check for battery voltage
before we start charging. And then we finally can lower the charge voltage
to 4.2V.
Note that we've been using the same register values as the Android distros
on droid4, so it is suspected that the same problem also exists in Android.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Rob Herring <robh+dt@kernel.org>
Reported-by: Merlijn Wajer <merlijn@wizzup.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
We are currently not enabling VBUS boost for cpcap when in host mode.
This means the VBUS is fed at the battery voltage level, which can cause
flakeyness enumerating devices.
Looks like the boost control for VBUS is CPCAP_BIT_VBUS_SWITCH that we
must enable in the charger for nice 4.92 V VBUS output. And looks like
we must not use the STBY pin enabling but must instead use manual VBUS
control in phy-cpcap-usb.
We want to do this in cpcap_charger_vbus_work() and also set a flag for
feeding_vbus to avoid races between USB detection and charger detection,
and disable charging if feeding_vbus is set.
Cc: Jacopo Mondi <jacopo@jmondi.org>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Merlijn Wajer <merlijn@wizzup.org>
Cc: Michael Scott <hashcode0f@gmail.com>
Cc: NeKit <nekit1000@gmail.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Sebastian Reichel <sre@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation this program is
distributed in the hope that it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 655 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
With loadable modules we may get the following during init:
could not initialize VBUS or ID IIO: -517
Let's not print any pointless error messages for deferred probe.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
The driver doesn't generate uevents on charger connect/disconnect.
This leads to UPower not detecting when AC is on or off... and that is
bad.
Reported by Arthur D. on github (
https://github.com/maemo-leste/bugtracker/issues/206 ), thanks to
Merlijn Wajer for suggesting a fix.
Cc: stable@kernel.org
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Trivial fix to clean up indentation issue, remove an extraneous tab
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Function platform_get_irq_byname() returns a negative error code on
failure, and a zero or positive number on success. However, in function
cpcap_usb_init_irq(), positive IRQ numbers are also taken as error
cases. Use "if (irq < 0)" instead of "if (!irq)" to validate the return
value of platform_get_irq_byname().
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Otherwise cpcap-battery won't probe properly with the power-supplies
property configured but will fail with "Not all required supplies found,
defer probe".
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
With the ADC driver working, we can now fix the voltage table based on
the values read from the ADC.
Note that unlike the ICHRG registers, the VCHRG register bits don't
match the MC13783UG.pdf.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Turns out a similar battery charger hardware is documented for NXP MC13783
PMIC in "MC13783 Power Management and Audio Circuit Users's Guide" named
MC13783UG.pdf. Looks like the CPCAP charge current table matches that, so
let's start using the nominal values from it.
While at it, let's also add comments to some of the mystery CPCAP charger
registers based on the MC13783UG.pdf documentation.
Note that this patch does not contain any functional changes, the register
values being used stay the same.
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Android does not seem to set the trickle charger bits, and these
seem to be only used by the bootloader when bringing up a
completely discharged battery. So let's keep the trickle charging
bits disabled and avoid misconfiguring the hardware.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal
CPCAP PMIC battery charger")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Zero is a valid register value for for 3.8V charging.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal
CPCAP PMIC battery charger")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
We have the charge voltage wrong, it should be 4.35V instead of 4.2V.
This will cause the battery to never get fully charged.
I noticed this when looking at the Andoid kernel battery and charger
status for a fully charged battery:
POWER_SUPPLY_VOLTAGE_NOW=4351000
Also the battery on droid 4 says "4.35, 1735/1785mAh (min/typ),
6.6/6.8 Wh (min/typ)". Presumably the 4.35 on the battery is the
charge voltage.
And finally, on Android the CPCAP CRM register is set to 0x03b5 where
the b is the charge voltage.
Let's fix the charge voltage define and update the charge configuration
to use the 4.35V setting.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal
CPCAP PMIC battery charger")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
I noticed we have a different name from what Android is using.
Let's not break the /sys/class/power user space interface here
and use the same naming as Android has.
On Android we have the following for droid 4:
$ ls /sys/class/power_supply/
ac battery usb
So let's use the usb naming here for charger too.
Fixes: 0c9888e3c1 ("power: supply: cpcap-charger: Add minimal
CPCAP PMIC battery charger")
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
The custom CPCAP PMIC used on Motorola phones such as Droid 4 has a
USB battery charger. It can optionally also have a companion chip that
is used for wireless charging.
The charger on CPCAP also can feed VBUS for the USB host mode. This
can be handled by the existing kernel phy_companion interface.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sebastian Reichel <sre@kernel.org>
Yang Li
