This is automatically set for all MIPS32 and MIPS64 processors.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add a helper routine to register tx4939ide driver and use it on
RBTX4939 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add leds-gpio platform device for controlling LEDs connected to IOC on
RBTX49XX and JMR3927 board.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The IOC interrupt status register on RBTX49XX only have 8 bits. Use
8-bit version of __fls() to optimize interrupt handlers.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TXx9 SoCs have pin multiplex. Stop some controller modules which can
not be used due to pin configurations.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch converts the rb532 code to use gpio library
and register its gpio chip.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch cleans up headers and regroups informations to
where they should reside. While moving, try to have a
consistant naming for defines.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are no longer using setup_serial_port. So just remove it
from the prom code.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When there is only platform device of the same type, id = -1
should be used, fix this.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch replaces a raw read using volatiles
with a readl.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We are no longer using gpio bootup state, so do not export
it and do not parse the kernel command line tag for it.
Instead we provide gpio-keys for the button the gpio bootup
state was checking.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the misuse of virtual addresses for the GPIO and third
device controller which would lead to problems while accessing ioremap'd
registers.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch moves GPIO related definitions to gpio.h and IRQ
related to irq.h
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Helper routines in txx9/rbtx4938/spi_eeprom.c is not TX4938 specific.
Move it to txx9/generic/ directory and make it works with SPI bus
number other than 0.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/txx9/generic/spi_eeprom.c
delete mode 100644 arch/mips/txx9/rbtx4938/spi_eeprom.c
Add TOSHIBA_RBTX4938_MPLEX_KEEP to keep MPLEX settings by firmware.
Also replace some printk with pr_info.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TX39/TX49 can enable/disable I/D cache at runtime. Add kernel options
to control them. This is useful to debug some cache-related issues,
such as aliasing or I/D coherency. Also enable CWF bit for TX49 SoCs.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add prom_getenv() which can be used for YAMON. This assumes other
firmware should pass NULL for fw_arg2.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Make prom_init_cmdline() static and be called from prom_init.
* Append built-in args if the first character was '+'.
* Drop command-line args if the first character of built-in was '-'.
* Enclose args include spaces by quotes.
* TX4938_NAND_BOOT is no longer needed.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Make sure all interrupts cleared on startup
* Initialize some GPIOs
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This new gpio driver for PMC-Sierra's MSP71xx SoC allows
standard api calls for access to the general and extended
gpio's.
Signed-off-by: Patrick Glass <patrickglass@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100755 arch/mips/pmc-sierra/msp71xx/gpio.c
create mode 100755 arch/mips/pmc-sierra/msp71xx/gpio_extended.c
create mode 100755 include/asm-mips/pmc-sierra/msp71xx/gpio.h
This replaces mips's sys_ptrace32 with a compat_arch_ptrace and
enables the new generic definition of compat_sys_ptrace instead.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'sched-v28-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (38 commits)
sched debug: add name to sched_domain sysctl entries
sched: sync wakeups vs avg_overlap
sched: remove redundant code in cpu_cgroup_create()
sched_rt.c: resch needed in rt_rq_enqueue() for the root rt_rq
cpusets: scan_for_empty_cpusets(), cpuset doesn't seem to be so const
sched: minor optimizations in wake_affine and select_task_rq_fair
sched: maintain only task entities in cfs_rq->tasks list
sched: fixup buddy selection
sched: more sanity checks on the bandwidth settings
sched: add some comments to the bandwidth code
sched: fixlet for group load balance
sched: rework wakeup preemption
CFS scheduler: documentation about scheduling policies
sched: clarify ifdef tangle
sched: fix list traversal to use _rcu variant
sched: turn off WAKEUP_OVERLAP
sched: wakeup preempt when small overlap
kernel/cpu.c: create a CPU_STARTING cpu_chain notifier
kernel/cpu.c: Move the CPU_DYING notifiers
sched: fix __load_balance_iterator() for cfq with only one task
...
Symbol name spaghetti which is too complicated to cleanup on this stage
of the release cycle breaks the build on BCM1480 platforms.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6:
ide: workaround for bogus gcc warning in ide_sysfs_register_port()
ide-cd: Optiarc DVD RW AD-7200A does play audio
IDE: Fix platform device registration in Swarm IDE driver (v2)
ide-dma: fix ide_build_dmatable() for TRM290
ide-cd: temporary tray close fix
The Swarm IDE driver uses a release method which is defined in the driver
itself thus potentially oopsable. The simple fix would be to just leak
the device but this patch goes the full length and moves the entire
handling of the platform device in the platform code and retains only
the platform driver code in drivers/ide/mips/swarm.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: "Maciej W. Rozycki" <macro@linux-mips.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[bart: remove no longer needed BLK_DEV_IDE_SWARM from ide/Kconfig]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Rework of SMTC support to make it work with the new clock event system,
allowing "tickless" operation, and to make it compatible with the use of
the "wait_irqoff" idle loop. The new clocking scheme means that the
previously optional IPI instant replay mechanism is now required, and has
been made more robust.
Signed-off-by: Kevin D. Kissell <kevink@paralogos.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Though from a hardware perspective it would be sensible to use only a
32-bit unsigned int type Linux defines interrupt flags to be stored in
an unsigned long and nothing else.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus:
[SSB] Initialise dma_mask for SSB_BUSTYPE_SSB devices
[MIPS] BCM47xx: Fix build error due to missing PCI functions
[MIPS] IP27: Switch to dynamic interrupt routing avoding panic on error.
[MIPS] au1000: Make sure GPIO value is zero or one
This patch defines pcibios_map_irq() and pcibios_plat_dev_init() for
the BCM47xx platform.
It fixes the regression introduced by commit
aab547ce0d.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pcibios_map_irq is no way of returning an error but on IP27 an interrupt
is possibly not routable when running out of resources. So do the
interrupt routing at pcibios_enable_device time.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
David Brownell <david-b@pacbell.net> wrote:
> The problem is that "value" is zero-or-nonzero.
> This code wrongly assumes it's zero-or-one.
> Possible fix: "((!!value) << gpio)".
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On the x86 arch, user space single step exceptions should be ignored
if they occur in the kernel space, such as ptrace stepping through a
system call.
First check if it is kgdb that is executing a single step, then ensure
it is not an accidental traversal into the user space, while in kgdb,
any other time the TIF_SINGLESTEP is set, kgdb should ignore the
exception.
On x86, arm, mips and powerpc, the kgdb_contthread usage was
inconsistent with the way single stepping is implemented in the kgdb
core. The arch specific stub should always set the
kgdb_cpu_doing_single_step correctly if it is single stepping. This
allows kgdb to correctly process an instruction steps if ptrace
happens to be requesting an instruction step over a system call.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
When setting the direction of one GPIO pin we have to keep the state of the
other pins, hence use binary OR. Also gpio_direction_output() wants to set an
initial value, so add that too.
This fixes a problem with the USB power switch on mtx-1 boards.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The -ffunction-sections puts each text in .text.function_name section.
Without this patch, most functions are placed outside _text..._etext
area and it breaks show_stacktrace(), etc.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If an interrupt happened between checking of NEED_RESCHED and WAIT
instruction, adjust EPC to restart from checking of NEED_RESCHED.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use unsigned loads to avoid possible misscalculation of IP checksums. This
bug was instruced in f761106cd728bcf65b7fe161b10221ee00cf7132 (lmo) /
ed99e2bc1d (kernel.org).
[Original fix by Atsushi. Improved instruction scheduling and fix for
unaligned unsigned load by me -- Ralf]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Right now, there is no notifier that is called on a new cpu, before the new
cpu begins processing interrupts/softirqs.
Various kernel function would need that notification, e.g. kvm works around
by calling smp_call_function_single(), rcu polls cpu_online_map.
The patch adds a CPU_STARTING notification. It also adds a helper function
that sends the message to all cpu_chain handlers.
Tested on x86-64.
All other archs are untested. Especially on sparc, I'm not sure if I got
it right.
Signed-off-by: Manfred Spraul <manfred@colorfullife.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The second HPC3 could be found only on Guiness systems (Challenge-S),
but not on fullhouse (Indigo2) systems.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch also includes the required removal of (unused) inclusion of
<asm/a.out.h> <linux/a.out.h>'s in the arch/ code for these
architectures.
[dwmw2: updated for 2.6.27-rc]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Currently init_initrd() probes initrd header at the last page of kernel
image, but it is valid only if addinitrd was used. If addinitrd was not
used, the area contains garbage so probing there might misdetect initrd
header (magic number is not strictly robust).
This patch introduces CONFIG_PROBE_INITRD_HEADER to explicitly enable this
probing.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The txx9_pcode variable was introduced in commit
fe1c2bc64f65003b39f331a8e4b0d15b235a4afd ("TXx9: Add 64-bit support")
but was not initialized properly.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
trap_init issues flush_icache_range(), which uses ipi functions to
get icache flushing done on all cpus. But this is done before interrupts
are enabled and caused WARN_ON messages. This changeset introduces
a new local_flush_icache_range() and uses it before interrupts (and
additional CPUs) are enabled to avoid this problem.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With -ffunction-section the entries in __dbe_table aren't no longer
sorted, so the lookup of exception addresses in do_be() failed for
some addresses. To avoid this we now sort __dbe_table.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
kgdb_mips_notify is called on IBE/DBE/FPE/BP/TRAP/RI exception. None
of them need fixup. And doing fixup for a breakpoint exception will
confuse gdb.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the register definitions of the MPMC controller from
mach-rc32434/rb.h instead of redefining them.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
CC arch/mips/emma2rh/markeins/setup.o
In file included from arch/mips/emma2rh/markeins/setup.c:30:
include/linux/ide.h:645: error: ‘CONFIG_IDE_MAX_HWIFS’ undeclared here (not in a function)
make[1]: *** [arch/mips/emma2rh/markeins/setup.o] Error 1
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch remove unneeded #include <linux/ide.h>'s.
It also adds a required #include <linux/interrupt.h> that was previously
implicitely pulled by ide.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
[bart: revert change to tests/lkdtm.c (spotted by Stephen Rothwell)]
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The new kgdb architecture specific handler registers and unregisters
dynamically for exceptions depending on when you configure a kgdb I/O
driver.
Aside from initializing the exceptions earlier in the boot process,
kgdb should have no impact on a device when it is compiled in so long
as an I/O module is not configured for use.
There have been quite a number of contributors during the existence of
this patch (see arch/mips/kernel/kgdb.c). Most recently Jason
re-wrote the mips kgdb logic to use the die notification handlers.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch explicitly removes the kgdb implementation, for mips which
is intended to be followed by a patch that adds a kgdb implementation
for MIPS that makes use of the kgdb core in the kernel.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Unify calling of early_serial_txx9_setup.
* Use dedicated serial clock on RBTX4938.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Random cleanups spotted by checkpatch script.
* Do not initialize panic_timeout. "panic=" kernel parameter can be used.
* Do not add "ip=any" or "ip=bootp". This options is not board specific.
* Do not add "root=/dev/nfs". This is default on CONFIG_ROOT_NFS.
* Kill unused error checking.
* Fix IRQ comment to match current code.
* Kill some unneeded includes
* ST0_ERL is already cleared in generic code.
* conswitchp is initialized generic code.
* __init is not needed in prototype.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make some TX4938 SoC specific code independent from board specific code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make some TX3927 SoC specific code independent from board specific code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A recent generic change now catches such bugs:
<-- snip -->
...
CC arch/mips/rb532/time.o
cc1: warnings being treated as errors
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c: In function 'plat_time_init':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c:55: error: comparison of distinct pointer types lacks a cast
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/rb532/time.c:66: error: comparison of distinct pointer types lacks a cast
make[2]: *** [arch/mips/rb532/time.o] Error 1
<-- snip -->
Reported-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
An earlier update changed some calls from simple_strotl to strict_strtol but
did not account for the differences in the syntax between the calls.
simple_strotl returns the integer; strict_strtol returns an error code and
takes a pointer to the result. As it was, NULL was being passed in place of
the result, which led to failures during kernel initialization when using
YAMON.
Signed-off-by: Kevin Hickey <khickey@rmicorp.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Bug originally found and reported by Julia Lawall <julia@diku.dk>. I
decieded that the whole error check was mostly useless paranoia and should
be discarded. It would only ever trigger if r3k_have_wired_reg has a wrong
value.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove arch-specific show_mem() in favor of the generic version.
This also removes the following redundant information display:
- pages in swapcache, printed by show_swap_cache_info()
where show_mem() calls show_free_areas(), which calls
show_swap_cache_info().
And show_mem() does now actually print something on configurations
with multiple nodes.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add per-device dma_mapping_ops support for CONFIG_X86_64 as POWER
architecture does:
This enables us to cleanly fix the Calgary IOMMU issue that some devices
are not behind the IOMMU (http://lkml.org/lkml/2008/5/8/423).
I think that per-device dma_mapping_ops support would be also helpful for
KVM people to support PCI passthrough but Andi thinks that this makes it
difficult to support the PCI passthrough (see the above thread). So I
CC'ed this to KVM camp. Comments are appreciated.
A pointer to dma_mapping_ops to struct dev_archdata is added. If the
pointer is non NULL, DMA operations in asm/dma-mapping.h use it. If it's
NULL, the system-wide dma_ops pointer is used as before.
If it's useful for KVM people, I plan to implement a mechanism to register
a hook called when a new pci (or dma capable) device is created (it works
with hot plugging). It enables IOMMUs to set up an appropriate
dma_mapping_ops per device.
The major obstacle is that dma_mapping_error doesn't take a pointer to the
device unlike other DMA operations. So x86 can't have dma_mapping_ops per
device. Note all the POWER IOMMUs use the same dma_mapping_error function
so this is not a problem for POWER but x86 IOMMUs use different
dma_mapping_error functions.
The first patch adds the device argument to dma_mapping_error. The patch
is trivial but large since it touches lots of drivers and dma-mapping.h in
all the architecture.
This patch:
dma_mapping_error() doesn't take a pointer to the device unlike other DMA
operations. So we can't have dma_mapping_ops per device.
Note that POWER already has dma_mapping_ops per device but all the POWER
IOMMUs use the same dma_mapping_error function. x86 IOMMUs use device
argument.
[akpm@linux-foundation.org: fix sge]
[akpm@linux-foundation.org: fix svc_rdma]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix bnx2x]
[akpm@linux-foundation.org: fix s2io]
[akpm@linux-foundation.org: fix pasemi_mac]
[akpm@linux-foundation.org: fix sdhci]
[akpm@linux-foundation.org: build fix]
[akpm@linux-foundation.org: fix sparc]
[akpm@linux-foundation.org: fix ibmvscsi]
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Muli Ben-Yehuda <muli@il.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Avi Kivity <avi@qumranet.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds functionality to the gpio-lib subsystem to make it
possible to enable the gpio-lib code even if the architecture code didn't
request to get it built in.
The archtitecture code does still need to implement the gpiolib accessor
functions in its asm/gpio.h file. This patch adds the implementations for
x86 and PPC.
With these changes it is possible to run generic GPIO expansion cards on
every architecture that implements the trivial wrapper functions. Support
for more architectures can easily be added.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: David Brownell <david-b@pacbell.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
nohz: adjust tick_nohz_stop_sched_tick() call of s390 as well
nohz: prevent tick stop outside of the idle loop
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
arch/mips/kernel/stacktrace.c: Heiko can't type
kthread: reduce stack pressure in create_kthread and kthreadd
fix core/stacktrace changes on avr32, mips, sh
This patch introduces the new syscall pipe2 which is like pipe but it also
takes an additional parameter which takes a flag value. This patch implements
the handling of O_CLOEXEC for the flag. I did not add support for the new
syscall for the architectures which have a special sys_pipe implementation. I
think the maintainers of those archs have the chance to go with the unified
implementation but that's up to them.
The implementation introduces do_pipe_flags. I did that instead of changing
all callers of do_pipe because some of the callers are written in assembler.
I would probably screw up changing the assembly code. To avoid breaking code
do_pipe is now a small wrapper around do_pipe_flags. Once all callers are
changed over to do_pipe_flags the old do_pipe function can be removed.
The following test must be adjusted for architectures other than x86 and
x86-64 and in case the syscall numbers changed.
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
#include <fcntl.h>
#include <stdio.h>
#include <unistd.h>
#include <sys/syscall.h>
#ifndef __NR_pipe2
# ifdef __x86_64__
# define __NR_pipe2 293
# elif defined __i386__
# define __NR_pipe2 331
# else
# error "need __NR_pipe2"
# endif
#endif
int
main (void)
{
int fd[2];
if (syscall (__NR_pipe2, fd, 0) != 0)
{
puts ("pipe2(0) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if (coe & FD_CLOEXEC)
{
printf ("pipe2(0) set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
if (syscall (__NR_pipe2, fd, O_CLOEXEC) != 0)
{
puts ("pipe2(O_CLOEXEC) failed");
return 1;
}
for (int i = 0; i < 2; ++i)
{
int coe = fcntl (fd[i], F_GETFD);
if (coe == -1)
{
puts ("fcntl failed");
return 1;
}
if ((coe & FD_CLOEXEC) == 0)
{
printf ("pipe2(O_CLOEXEC) does not set close-on-exit for fd[%d]\n", i);
return 1;
}
}
close (fd[0]);
close (fd[1]);
puts ("OK");
return 0;
}
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Acked-by: Davide Libenzi <davidel@xmailserver.org>
Cc: Michael Kerrisk <mtk.manpages@googlemail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove the obsolete and no longer used include/linux/pm_legacy.h
Reviewed-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Cc: Pavel Machek <pavel@suse.cz>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On 32-bit architectures PAGE_ALIGN() truncates 64-bit values to the 32-bit
boundary. For example:
u64 val = PAGE_ALIGN(size);
always returns a value < 4GB even if size is greater than 4GB.
The problem resides in PAGE_MASK definition (from include/asm-x86/page.h for
example):
#define PAGE_SHIFT 12
#define PAGE_SIZE (_AC(1,UL) << PAGE_SHIFT)
#define PAGE_MASK (~(PAGE_SIZE-1))
...
#define PAGE_ALIGN(addr) (((addr)+PAGE_SIZE-1)&PAGE_MASK)
The "~" is performed on a 32-bit value, so everything in "and" with
PAGE_MASK greater than 4GB will be truncated to the 32-bit boundary.
Using the ALIGN() macro seems to be the right way, because it uses
typeof(addr) for the mask.
Also move the PAGE_ALIGN() definitions out of include/asm-*/page.h in
include/linux/mm.h.
See also lkml discussion: http://lkml.org/lkml/2008/6/11/237
[akpm@linux-foundation.org: fix drivers/media/video/uvc/uvc_queue.c]
[akpm@linux-foundation.org: fix v850]
[akpm@linux-foundation.org: fix powerpc]
[akpm@linux-foundation.org: fix arm]
[akpm@linux-foundation.org: fix mips]
[akpm@linux-foundation.org: fix drivers/media/video/pvrusb2/pvrusb2-dvb.c]
[akpm@linux-foundation.org: fix drivers/mtd/maps/uclinux.c]
[akpm@linux-foundation.org: fix powerpc]
Signed-off-by: Andrea Righi <righi.andrea@gmail.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a lot of places that define either a single bootmem descriptor or an
array of them. Use only one central array with MAX_NUMNODES items instead.
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Hirokazu Takata <takata@linux-m32r.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Cc: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
device_create() is race-prone, so use the race-free
device_create_drvdata() instead as device_create() is going away.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SYS_SUPPORTS_64BIT_KERNEL is enabled for RBTX4927/RBTX4938, but
actually it was broken for long time (or from the beginning). Now it
should work.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Commit 3e6ea3b0d7a93550a93a265e732413d3a5aaf0d2 (linux-mips.org) /
52f4f6bbcf (kernel.org)
([MIPS] Use kernel-supplied ARRAY_SIZE() macro.)
causes the following compile error:
<-- snip -->
...
CC arch/mips/sgi-ip22/ip28-berr.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/sgi-ip22/ip28-berr.c: In function 'ip28_be_interrupt':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/sgi-ip22/ip28-berr.c:415: error: subscripted value is neither array nor pointer
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/sgi-ip22/ip28-berr.c:415: error: subscripted value is neither array nor pointer
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/sgi-ip22/ip28-berr.c:415: warning: type defaults to 'int' in declaration of 'type name'
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/sgi-ip22/ip28-berr.c:424: error: subscripted value is neither array nor pointer
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/sgi-ip22/ip28-berr.c:424: error: subscripted value is neither array nor pointer
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/sgi-ip22/ip28-berr.c:424: warning: type defaults to 'int' in declaration of 'type name'
make[2]: *** [arch/mips/sgi-ip22/ip28-berr.o] Error 1
<-- snip -->
Using ARRAY_SIZE in these places in arch/mips/sgi-ip22/ip28-berr.c was
bogus, and therefore gets reverted by this patch.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Instead of one SGI_HAS_HAL2 for IP22 and one for IP28, IP28 got two of
them... Let's give IP22 some ALSA sound, too.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>[MIPS] IP22, IP28: Fix merge bug
Instead of one SGI_HAS_HAL2 for IP22 and one for IP28, IP28 got two of
them... Let's give IP22 some ALSA sound, too.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
While building the Malta defconfig, sparse spat the following
warnings:
>>>>>>>>>>>>>>>>>>
arch/mips/math-emu/kernel_linkage.c:31:6: warning: symbol
'fpu_emulator_init_fpu' was not declared. Should it be static?
arch/mips/math-emu/kernel_linkage.c:54:5: warning: symbol
'fpu_emulator_save_context' was not declared. Should it be
static?
arch/mips/math-emu/kernel_linkage.c:68:5: warning: symbol
'fpu_emulator_restore_context' was not declared. Should it be
static?
>>>>>>>>>>>>>>>>>>
This patch fixes these errors by adding the proper prototypes
to the include/asm-mips/fpu.h header, and actually using this
header in the sparse-spotted source file.
Build-tested with Malta defconfig.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The pcibios_max_latency variable is needlessly defined global, and this
patch makes it static.
Build-tested using malta_defconfig.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Jack Ren and Eric Miao tracked down the following long standing
problem in the NOHZ code:
scheduler switch to idle task
enable interrupts
Window starts here
----> interrupt happens (does not set NEED_RESCHED)
irq_exit() stops the tick
----> interrupt happens (does set NEED_RESCHED)
return from schedule()
cpu_idle(): preempt_disable();
Window ends here
The interrupts can happen at any point inside the race window. The
first interrupt stops the tick, the second one causes the scheduler to
rerun and switch away from idle again and we end up with the tick
disabled.
The fact that it needs two interrupts where the first one does not set
NEED_RESCHED and the second one does made the bug obscure and extremly
hard to reproduce and analyse. Kudos to Jack and Eric.
Solution: Limit the NOHZ functionality to the idle loop to make sure
that we can not run into such a situation ever again.
cpu_idle()
{
preempt_disable();
while(1) {
tick_nohz_stop_sched_tick(1); <- tell NOHZ code that we
are in the idle loop
while (!need_resched())
halt();
tick_nohz_restart_sched_tick(); <- disables NOHZ mode
preempt_enable_no_resched();
schedule();
preempt_disable();
}
}
In hindsight we should have done this forever, but ...
/me grabs a large brown paperbag.
Debugged-by: Jack Ren <jack.ren@marvell.com>,
Debugged-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fixes this type of problem:
CC arch/s390/kernel/stacktrace.o
arch/s390/kernel/stacktrace.c:84: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:84: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:84: warning: parameter names (without types) in function declaration
arch/s390/kernel/stacktrace.c:97: warning: data definition has no type or storage class
arch/s390/kernel/stacktrace.c:97: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL'
arch/s390/kernel/stacktrace.c:97: warning: parameter names (without types) in function declaration
caused by "stacktrace: export save_stack_trace[_tsk]"
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6: (72 commits)
Revert "x86/PCI: ACPI based PCI gap calculation"
PCI: remove unnecessary volatile in PCIe hotplug struct controller
x86/PCI: ACPI based PCI gap calculation
PCI: include linux/pm_wakeup.h for device_set_wakeup_capable
PCI PM: Fix pci_prepare_to_sleep
x86/PCI: Fix PCI config space for domains > 0
Fix acpi_pm_device_sleep_wake() by providing a stub for CONFIG_PM_SLEEP=n
PCI: Simplify PCI device PM code
PCI PM: Introduce pci_prepare_to_sleep and pci_back_from_sleep
PCI ACPI: Rework PCI handling of wake-up
ACPI: Introduce new device wakeup flag 'prepared'
ACPI: Introduce acpi_device_sleep_wake function
PCI: rework pci_set_power_state function to call platform first
PCI: Introduce platform_pci_power_manageable function
ACPI: Introduce acpi_bus_power_manageable function
PCI: make pci_name use dev_name
PCI: handle pci_name() being const
PCI: add stub for pci_set_consistent_dma_mask()
PCI: remove unused arch pcibios_update_resource() functions
PCI: fix pci_setup_device()'s sprinting into a const buffer
...
Fixed up conflicts in various files (arch/x86/kernel/setup_64.c,
arch/x86/pci/irq.c, arch/x86/pci/pci.h, drivers/acpi/sleep/main.c,
drivers/pci/pci.c, drivers/pci/pci.h, include/acpi/acpi_bus.h) from x86
and ACPI updates manually.
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (54 commits)
[MIPS] Remove mips_machtype for LASAT machines
[MIPS] Remove mips_machtype from EMMA2RH machines
[MIPS] Remove mips_machtype from ARC based machines
[MIPS] MTX-1 flash partition setup move to platform devices registration
[MIPS] TXx9: cleanup and fix some sparse warnings
[MIPS] TXx9: rename asm-mips/mach-jmr3927 to asm-mips/mach-tx39xx
[MIPS] remove machtype for group Toshiba
[MIPS] separate rbtx4927_time_init() and rbtx4937_time_init()
[MIPS] separate rbtx4927_arch_init() and rbtx4937_arch_init()
[MIPS] txx9_cpu_clock setup move to rbtx4927_time_init()
[MIPS] txx9_board_vec set directly without mips_machtype
[MIPS] IP22: Add platform device for Indy volume buttons
[MIPS] cmbvr4133: Remove support
[MIPS] remove wrppmc_machine_power_off()
[MIPS] replace inline assembler to cpu_wait()
[MIPS] IP22/28: Add platform devices for HAL2
[MIPS] TXx9: Update and merge defconfigs
[MIPS] TXx9: Make single kernel can support multiple boards
[MIPS] TXx9: Update defconfigs
[MIPS] TXx9: Reorganize PCI code
...
* 'i2c-for-linus' of git://jdelvare.pck.nerim.net/jdelvare-2.6: (56 commits)
i2c: Add detection capability to new-style drivers
i2c: Call client_unregister for new-style devices too
i2c: Clean up old chip drivers
i2c-ibm_iic: Register child nodes
i2c: New-style EEPROM driver using device IDs
i2c: Export the i2c_bus_type symbol
i2c-au1550: Fix PM support
i2c-dev: Delete empty detach_client callback
i2c: Drop stray references to lm_sensors
i2c: Check for ACPI resource conflicts
i2c-ocores: basic PM support
i2c-sibyte: SWARM I2C board initialization
i2c-i801: Fix handling of error conditions
i2c-i801: Rename local variable temp to status
i2c-i801: Properly report bus arbitration loss
i2c-i801: Remove verbose debugging messages
i2c-algo-pcf: Drop unused struct members
i2c-algo-pcf: Multi-master lost-arbitration improvement
i2c: Deprecate the legacy gpio drivers
i2c-pxa: Initialize early
...
This is the LASAT part of the mips_machtype removal.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the EMMA2RH part of the mips_machtype removal.
[Ralf: Fixed to the #error statements]
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the ARC part of the mips_machtype removal.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Do not return void value
* Make some functions static
* Do not include unnecessary bootinfo.h
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Rename mach-jmr3927 directory to more proper name to make adding other
platforms easier.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It cannot be built for a long time and nobody maintains it.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Merge rbhma4200(RBTX4927/37) and rbhma4500(RBTX4938) defconfig into
single rbtx49xx defconfig. And jmr3927 defconfig is also updated.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Make single kernel can be used on RBTX4927/37/38. Also make
some SoC-specific code independent from board-specific code.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Split out PCIC dependent code and SoC dependent code from board dependent
code. Now TX4927 PCIC code is independent from TX4927/TX4938 SoC code.
Also fix some build problems on CONFIG_PCI=n.
As a bonus, "FPCIB0 Backplane Support" is available for all TX39/TX49 boards
and PCI66 support is available for all TX49 boards.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move arch/mips/{jmr3927,tx4927,tx4938} into arch/mips/txx9/ tree.
This will help more code sharing and maintainance.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
TXx9 GPIO set/get routines are spinlock-safe. This patch make
gpio_direction_{input,output} routines also spinlock-safe so that they
can be used during early board setup.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
-ffunction-sections serves as a workaround for the problems caused by the
limited branch range in some inline assembler fragments for very large
compilation units.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Declare pci_probe_only, etc. in asm-mips/pci.h file. This will fix
some sparse warnings.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
SGI-IP28 is running in so called slow mode, when kernel is started
from the PROM. PROM calls must be done in slow mode otherwise the
PROM will issue an error. To get better memory performance we now
switch to normal mode, when the PROM is no longer needed.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following errors were caught by sparse:
>>>>>>>>>>>
arch/mips/mips-boards/generic/display.c:30:6: warning: symbol
'mips_display_message' was not declared. Should it be static?
arch/mips/mips-boards/generic/display.c:58:6: warning: symbol
'mips_scroll_message' was not declared. Should it be static?
>>>>>>>>>>>
This patch includes the asm/mips-boards/prom.h header file into
arch/mips/mips-boards/generic/display.c. This adds the needed
function declarations, and the errors are gone.
Compile-tested using defconfigs for Malta, Atlas and SEAD boards.
Runtime test was successfully performed by booting a Malta 4Kc
board up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The gcmp_probe() function is needlessly defined global, and
this patch makes it static.
Tested by booting a Malta 4Kc board up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Both the fill_ipi_map() routine and the gic_intr_map array defined
in arch/mips/mips-boards/malta/malta_int.c are not used outside of
the latter file. Thus, these objects can become static. Moreover,
these two objects are used by the MT code only, which is why this
patch adds the appropriate ifdef.
While at it, this patch removes an unnecessary preprocessing macro
in favor of the commonly used ARRAY_SIZE.
Successfully tested using a Qemu-emulated Malta board for both SMP
and UP kernels.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following symbols
hose_head
hose_tail
are needlessly defined global in arch/mips/pci/pci.c, and
this patch makes them static.
The variable pci_isa_hose is not used, and is removed by
this patch.
Spotted by namespacecheck. Tested by booting a Malta 4Kc
board up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The pit_clockevent symbol is needlessly defined global. This patch makes
that variable static.
Spotted by sparse. Compile-tested using Malta defconfig.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Both onboard controller of the O2 support FAST-20 transfer speeds,
but the bit, which signals that to the aic driver, isn't set. Instead
of adding detection code to the scsi driver, we just fake the missing
bit in the PCI config space of the scsi chips.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Never terribly functional or popular, plagued by hard to fix bugs the time
to say goodbye has more than arrived.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following routines
allocate_irqno()
free_irqno()
seem not to be used outside of the core kernel code, hence
exporting these functions is pointless. This patch removes
the export.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following routines
uasm_rel_highest()
uasm_rel_higher()
are needlessly defined global. This patch makes them static.
Compile-tested using a customized config for the Malta board. Booting
the same board up to the shell prompt was also successful with this
patch applied.
Spotted by sparse.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following sparse warning:
<<<<<<<<
arch/mips/kernel/early_printk.c:35:13: warning: symbol 'setup_early_printk'
was not declared. Should it be static?
<<<<<<<<
The fix is to define a prototype of the setup_early_printk() function and
to include the appropriate header into arch/mips/kernel/early_printk.c.
[Ralf: Sorted includes again]
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The isa_slot_offset variable and its __ISA_IO_base macro is not used
anywhere anymore. It does not look like a decent interface per today's
standards either. Remove both including all places of initialization.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is not used anywhere in tree.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The standard rtc-m41t80.c driver cannot be used with the SWARM as it is,
because the board does not provide setup information for the I2C core.
As a result the bus and the address to probe for the M41T80 chip is not
known.
Here is a set of changes that fix the problem:
1. swarm-i2c.c -- SWARM I2C board setup, currently for the M41T80 chip on
the bus #1 only (there is a MAX6654 temperature sensor on the bus #0
which may be added in the future if we have a driver for that chip).
2. The i2c-sibyte.c BCM1250A SMBus controller driver now registers its
buses as numbered so that board setup is correctly applied.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The generated copy_page for R4k CPU with a 128 byte cache line size used
Create Dirty Exclusive cache line operations even if only part of the
cache line was filled. This change avoids generating cache operations,
if only part of the cache line size is copied in one loop. It also
increases the maxmimum loop size, because the generated code even fits
into the available space for r4k CPUs with 128 byte cache line size.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Resolve these mismatches by defining affected functions with the __cpuinit
attribute, rather than __init.
Signed-off-by: Shane McDonald <mcdonald.shane@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The txx9_tmr_init() will not clear a timer counter register in a certain
case. The counter register is cleared on 1->0 transition of TCE bit if
CRE=1. So just clearing the TCE bit is not enough.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The introduction of a real dma cache invalidate makes it important
to have a correct cache line size, otherwise the kernel will gives
out two memory segment, which might share one cache line. The R4400
Indy/Indigo2 CPU modules are using a second level cache line size
of 128 bytes, so MIPS_L1_CACHE_SHIFT needs to be bumped up to 7 for
IP22.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It's possible that the crime interrupt handler is called without
pending interrupts (probably a hardware issue). To avoid irritating
"unexpected irq 71" messages, we now just ignore the spurious crime
interrupts.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Andrew Morton reported this against linux-next:
ERROR: ".save_stack_trace" [tests/backtracetest.ko] undefined!
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Russell King did the following back in 2003:
<-- snip -->
[PCI] pci-9: Kill per-architecture pcibios_update_resource()
Kill pcibios_update_resource(), replacing it with pci_update_resource().
pci_update_resource() uses pcibios_resource_to_bus() to convert a
resource to a device BAR - the transformation should be exactly the
same as the transformation used for the PCI bridges.
pci_update_resource "knows" about 64-bit BARs, but doesn't attempt to
set the high 32-bits to anything non-zero - currently no architecture
attempts to do something different. If anyone cares, please fix; I'm
going to reflect current behaviour for the time being.
Ivan pointed out the following architectures need to examine their
pcibios_update_resource() implementation - they should make sure that
this new implementation does the right thing. #warning's have been
added where appropriate.
ia64
mips
mips64
This cset also includes a fix for the problem reported by AKPM where
64-bit arch compilers complain about the resource mask being placed
in a u32.
<-- snip -->
This patch removes the unused pcibios_update_resource() functions the
kernel gained since, from FRV, m68k, mips & sh architectures.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
It's never used and the comments refer to nonatomic and retry
interchangably. So get rid of it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This converts mips to use the new helpers for smp_call_function() and
friends, and adds support for smp_call_function_single(). Not tested,
but it compiles.
mips shares the same IPI for smp_call_function() and
smp_call_function_single(), since not all mips platforms have enough
available IPIs to support seperate setups.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Au12x0 MMC platform device strangely claims 0x41 bytes for its
memory-mapped registers. Make it claim the whole 0x80000 instead according
to the memory map given in the datasheets.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix 64-bit Malta by using CKSEG0ADDR and correct casts.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
LASAT's sysctl interface was broken, it failed a check during boot because
a single entry had a sysctl number and the rest were unnumbered. When I
fixed it I noticed that the whole sysctl file needed a spring clean, it was
using mutexes where it wasn't needed (it's only needed to protect during
writes to the EEPROM), so I moved that stuff out and generally cleaned the
whole thing up.
So now, LASAT's sysctl/proc interface is working again.
Signed-off-by: Thomas Horsten <thomas@horsten.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Assuming the call of kmap_coherent in local_r4k_flush_cache_page doesn't
need fixing this was skipped in fcae549295bcae801ac48fc1c2030ab8cc487020.
Turns out it needed the same change after all.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After the common MIPS CPU interrupt controller (for irq0-7) was introduced
the Lasat boards didn't get their interrupts right, so nothing worked. The
old routines need to be offset by the new 8 hardware interrupts common to
all MIPS CPU's.
Signed-off-by: Thomas Horsten <thomas@horsten.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The SWARM defconfig file has not been regenerated for over a year now.
Here is a patch to bring the file up to date. Additionally some important
and sometimes confusing changes happened meanwhile. Here is the list of
notable corresponding updates to the configuration:
1. CPU_SB1_PASS_2_2 is now selected rather than CPU_SB1_PASS_1. The
latter requires a non-standard -msb1-pass1-workarounds option to be
supported by GCC and I am told is quite rare anyway.
[Ralf: Afaik -msb1-pass1-workarounds is available only in Monta Vista's
special Sibyte gcc 3.0 variant and gcc 3.0 is too old to build a modern
kernel anyway.]
2. PHYLIB and BROADCOM_PHY are both built in and NETDEV_1000 enabled as
required by SB1250_MAC.
3. USB and USB_OHCI_HCD are enabled as there is an OHCI chip onboard.
4. TMPFS is enabled, because I use it. ;-)
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Build the SWARM platform library is as an object rather than an archive
so that files which only contain symbols used by initcalls and do not
provide any symbols that would pull them from an archive still work.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
RM200 with R5ks have a little bit different arcname.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use better load address for big endian kernels to avoid clashes with
PROM / SASH.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Correctly initialize io_map_base for the SB1250 PCI controller as required
for proper iomap support. Based on a proposal from Daniel Jacobowitz.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Changes in the generic bootmem code broke memory setup for IP27. This
patch fixes this by replacing lots of special IP27 code with generic
bootmon code. This has been tested only on a single node.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The existing options are named CONFIG_CPU_R4300 and CONFIG_CPU_R4X00,
and they are directly below.
Reported-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The newly added check for valid stack pointer address breaks at least for
64bit kernels. Use __get_user() for accessing stack content to avoid crashes,
when doing the backtrace.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Treat R4700 like R4600 in build_tlb_probe_entry. Without this fix kernel
will lock up.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add API to delete custom DDMA device ids create with
au1xxx_ddma_device_add().
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
au1xmmc.c driver depends on it, so export it for modules.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the following build errror caused by
commit 7dffa3c673
(ntp: handle leap second via timer):
<-- snip -->
...
CC arch/mips/emma2rh/markeins/setup.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/mips/emma2rh/markeins/setup.c:79: error: conflicting types for 'clock'
/home/bunk/linux/kernel-2.6/git/linux-2.6/include/linux/clocksource.h:96: error: previous declaration of 'clock' was here
make[2]: *** [arch/mips/emma2rh/markeins/setup.o] Error 1
<-- snip -->
[Ralf: reformated to 80 colums after the fix and marked emma2rh_clock as
__initdata]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix several errors and warnings given by checkpatch.pl:
- use of C99 // comments;
- using simple_strtol() where strict_strtol() could be used.
In addition to these changes, also do the following:
- remove needless parentheses;
- remove unneeded numeric literal type cast;
- insert spaces between operator and its operands;
- remove excess new lines;
- remove space after the type cast's closing parenthesis;
- insert missing space before closing brace in the structure initializer;
- fix typos, capitalize acronyms, etc. in the comments;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix many errors and warnings given by checkpatch.pl:
- space after opening and before closing parentheses;
- use of C99 // comments;
- leading spaces instead of tabs;
- brace not on the same line with 'else' in the 'if' statement;
statement;
- printk() without KERN_* facility level;
- using simple_strtol() where strict_strtol() could be used.
- including <asm/gpio.h> instead of <linux/gpio.h>.
In addition to these changes, also do the following:
- insert spaces between operator and its operands;
- replace tab between the function type and name with space in
mtx1_pci_idsel() declaration;
- remove space after the type cast's closing parenthesis;
- insert missing space before closing brace in the array/structure
initializers;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix several errors and warnings given by checkpatch.pl:
- use of C99 // comments;
- initialization of a 'static' variable to 0;
- space after opening and before closing parentheses;
- missing space between 'for' and opening parenthesis;
- macros with complex values not enclosed in parentheses;
- printk() without KERN_* facility level;
- unnecessary braces for single-statement block;
- using simple_strtol() where strict_strtol() could be used;
- line over 80 characters.
In addition to these changes, also do the following:
- mention DBAu1200 board in the Makefile;
- replace the group of #include/#ifdef directives by a single
#include <au1xxx.h> since this header contains the needed stuff;
- properly indent the blocks;
- insert spaces between operator and its operands, remove excess spaces
there;
- remove needless parentheses and add some for clarity;
- replace numeric literals/expressions with the matching macros;
- remove space after the type cast's closing parenthesis;
- reduce pb1200_setup_cascade() to the single 'return' statement;
- reduce the number of printed empty lines in the so-called CPLD
workaround;
- remove #undef AU1X00_EXTERNAL_INT since that macro is not defined
anywhere;
- replace spaces after the macro name with tabs in the #define directives;
- remove excess tabs after the macro name in the #define directives;
- fix typo in the BCSR_RESETS_PWMR1mUX macro's name;
- group all Pb1200 PCMCIA definitions together;
- put the function's result type and name/parameters on the same line;
- insert missing and remove excess new lines;
- make the multi-line comment style consistent with the kernel style
elsewhere by adding empty first line and/or adding space/asterisk on
their left side;
- fix typos/errors, capitalize acronyms, etc. in the comments;
- combine some comments;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix a few errors and warnings given by checkpatch.pl:
- macros with complex values not enclosed in parentheses;
- printk() without KERN_* facility level;
- unnecessary braces for single-statement block;
- using simple_strtol() where strict_strtol() could be used.
In addition to these changes, also do the following:
- replace numeric literals with the matching macros;
- properly indent the code and the array initializers;
- insert spaces between operator and its operands, also remove excess spaces
there;
- remove space after the type cast's closing parenthesis;
- insert missing space before closing brace in the array initializers;
- replace spaces after the macro name with tabs in the #define directives, also
sometimes insert space there for better looks;
- remove excess tabs after the macro name in the #define directives;
- fix typos/errors, capitalize acronyms, etc. in the comments;
- make the multi-line comment style consistent with the kernel style elsewhere
by adding empty first line;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix several errors and warnings given by checkpatch.pl:
- use of C99 // comments;
- printk() without KERN_* facility level;
- unnecessary braces for single-statement block;
- using simple_strtol() where strict_strtol() could be used.
In addition to these changes, also do the following:
- replace numeric literals/expressions with the matching macros;
- insert spaces between operator and its operands;
- properly indent the code and the array initializers;
- remove useless #if dirctive from board_setup();
- remove needless parentheses;
- remove unneeded type casts;
- remove excess new lines;
- make hexadecimal literals all lower case;
- remove space after the type cast's closing parenthesis;
- insert missing space before closing brace in the array initializers;
- replace spaces after the macro name with tabs in the #define directives,
also sometimes insert space there for better looks;
- fix typos/errors, capitalize acronyms, etc. in the comments;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix several errors and warnings given by checkpatch.pl:
- space between asterisk and variable name;
- use of C99 // comments;
- using simple_strtol() where strict_strtol() could be used.
In addition to these changes, also do the following:
- properly indent the code;
- remove space after the type cast's closing parenthesis;
- replace numeric literals/expressions with the matching macros;
- replace spaces after the macro name with tabs in the #define directives,
and sometimes insert spaces there;
- fix typos/errors, capitalize acronyms, etc. in the comments;
- make the multi-line comment style consistent with the kernel style
elsewhere by adding empty first line;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix several errors and warnings given by checkpatch.pl:
- use of C99 // comments;
- brace not on the same line with condition in the 'switch' statement;
- printk() without KERN_* facility level;
- unnecessary braces for single-statement block;
- using simple_strtol() where strict_strtol() could be used.
In addition to these changes, also do the following:
- properly indent the 'switch' statement;
- remove needless parentheses;
- insert spaces between operator and its operands;
- replace numeric literals/expressions with the matching macros;
- remove useless #if dirctive from board_setup();
- remove unneeded numeric literal type casts;
- remove space after the type cast's closing parenthesis;
- replace spaces after the macro name with tabs in the #define directives, and
sometimes insert spaces there;
- remove excess new lines;
- fix typos/errors, capitalize acronyms, etc. in the comments;
- make the multi-line comment style consistent with the kernel style elsewhere
by adding empty first/last line;
- combine some comments;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix several errors and warnings given by checkpatch.pl:
- macros with complex values not enclosed in parentheses;
- leading spaces instead of tabs;
- printk() without KERN_* facility level;
- using simple_strtol() where strict_strtol() could be used;
- line over 80 characters.
In addition to these changes, also do the following:
- initialize variable instead of assigning value later where it makes sense;
- insert spaces between operator and its operands, also remove excess spaces
there;
- remove unneeded numeric literal type casts;
- remove needless parentheses;
- remove space after the type cast's closing parenthesis;
- insert missing space before closing brace in the array initializers;
- replace spaces after the macro name with tabs in the #define directives;
- remove excess tabs after the macro name in the #define directives;
- fix typos/errors, capitalize acronyms, etc. in the comments;
- make the multi-line comment style consistent with the kernel style elsewhere
by adding empty first/last line;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix 15 errors and 4 warnings given by checkpatch.pl:
- space between the asterisk and variable name;
- space after opening and before closing parentheses;
- leading spaces instead of tabs;
- printk() without KERN_* facility level;
- unnecessary braces for single-statement block;
- line over 80 characters.
In addition to these changes, also do the following:
- combine the nested 'if' statements into one when possible;
- remove needless parentheses;
- add missing and remove excess spaces between operator and its operands;
- fix printk() format specifiers mismatching the argument types;
- put the function's result type and name/parameters on the same line;
- insert missing and remove excess new lines;
- properly indent multi-line expressions;
- make the multi-line comment style consistent with the kernel style elsewhere
by adding empty first line;
- fix typos, capitalize acronyms, etc. in the comments;
- update MontaVista copyright;
- remove Pete Popov's old email address...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix many errors and warnings given by checkpatch.pl:
- use of C99 // comments;
- missing space between the type and asterisk in a variable declaration;
- space between the asterisk and function/variable name;
- leading spaces instead of tabs;
- space after opening and before closing parentheses;
- initialization of a 'static' variable to 0;
- missing spaces around assignement/comparison operator;
- brace not on the same line with condition (or 'else') in the 'if'/'switch'
statement;
- missing space between 'if'/'for'/'while' and opening parenthesis;
- use of assignement in 'if' statement's condition;
- printk() without KERN_* facility level;
- EXPORT_SYMBOL() not following its function immediately;
- unnecessary braces for single-statement block;
- adding new 'typedef' (where including <linux/types.h> will do);
- use of 'extern' in the .c file (where it can be avoided by including header);
- line over 80 characters.
In addition to these changes, also do the following:
- insert missing space after opening brace and/or before closing brace in the
structure initializers;
- insert spaces between operator and its operands;
- put the function's result type and name/parameters on the same line;
- properly indent multi-line expressions;
- remove commented out code;
- remove useless initializers and code;
- remove needless parentheses;
- fix broken/excess indentation;
- add missing spaces between operator and its operands;
- insert missing and remove excess new lines;
- group 'else' and 'if' together where possible;
- make au1xxx_platform_init() 'static';
- regroup variable declarations in pm_do_freq() for prettier look;
- replace numeric literals with the matching macros;
- fix printk() format specifiers mismatching the argument types;
- make the multi-line comment style consistent with the kernel style elsewhere
by adding empty first line and/or adding space on their left side;
- make two-line comments that only have one line of text one-line;
- fix typos/errors, capitalize acronyms, etc. in the comments;
- fix/remove obsolete references in the comments;
- reformat some comments;
- add comment about the CPU:counter clock ratio to calc_clock();
- update MontaVista copyright;
- remove Pete Popov's and Steve Longerbeam's old email addresses...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is to clarify that GCC_IMM_ASM does not take an argument as the
context of the macro's invocation seems to imply.
As suggested by Maciej W. Rozycki (macro@linux-mips.org).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- remove always-true test
- neaten request_irq() indentation
This change's main purpose is to prepare for the patchset in
jgarzik/misc-2.6.git#irq-remove, that explores removal of the
never-used 'irq' argument in each interrupt handler.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch removes the no longer used export of __kmap_atomic_to_page.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
do_brk's return value was stored in an unsigned long variable before being
tested for less than zero making the test always fail. Also do_brk's
called irix_map_prda_page wasn't forwarding do_brk() success.
Bug checking the return value of do_brk() and initial fix for it found
by Roel Kluin <12o3l@tiscali.nl>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Alchemy platform code registers the SMBus device using the virtual
address of its registers instead of the physical one -- fix this, taking
into account that actually the whole megabyte is decoded by any of the
programmable serial controllers (one of which is SMBus), and that all the
Alchemy peripherals are directly mappable into KSEG1 kernel space and
therefore ioremap() call would just boil down to CKSEG1ADDR() invocation.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Existing code in there (get_tty(), etc.) is both severely
racy *and* pointless: ioctls in question have Linux equivalents
and there's no need to play silly buggers in irix_ioctl() -
just need to replace arguments and, in case of TIOCGSID,
deal with API differences - Linux one expects pid_t __user *
while Irix one does unsigned long __user *. BFD...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
x86 is the only arch right now, which provides an optimized for
div_long_long_rem and it has the downside that one has to be very careful that
the divide doesn't overflow.
The API is a little akward, as the arguments for the unsigned divide are
signed. The signed version also doesn't handle a negative divisor and
produces worse code on 64bit archs.
There is little incentive to keep this API alive, so this converts the few
users to the new API.
Signed-off-by: Roman Zippel <zippel@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (179 commits)
ACPI: Fix acpi_processor_idle and idle= boot parameters interaction
acpi: fix section mismatch warning in pnpacpi
intel_menlo: fix build warning
ACPI: Cleanup: Remove unneeded, multiple local dummy variables
ACPI: video - fix permissions on some proc entries
ACPI: video - properly handle errors when registering proc elements
ACPI: video - do not store invalid entries in attached_array list
ACPI: re-name acpi_pm_ops to acpi_suspend_ops
ACER_WMI/ASUS_LAPTOP: fix build bug
thinkpad_acpi: fix possible NULL pointer dereference if kstrdup failed
ACPI: check a return value correctly in acpi_power_get_context()
#if 0 acpi/bay.c:eject_removable_drive()
eeepc-laptop: add hwmon fan control
eeepc-laptop: add backlight
eeepc-laptop: add base driver
ACPI: thinkpad-acpi: bump up version to 0.20
ACPI: thinkpad-acpi: fix selects in Kconfig
ACPI: thinkpad-acpi: use a private workqueue
ACPI: thinkpad-acpi: fluff really minor fix
ACPI: thinkpad-acpi: use uppercase for "LED" on user documentation
...
Fixed conflicts in drivers/acpi/video.c and drivers/misc/intel_menlow.c
manually.
Use the macros provided in kbuild.h
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove proc_root export. Creation and removal works well if parent PDE is
supplied as NULL -- it worked always that way.
So, one useless export removed and consistency added, some drivers created
PDEs with &proc_root as parent but removed them as NULL and so on.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a proper extern for late_time_init in include/linux/init.h
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Almost all implementations of pci_iomap() in the kernel, including the generic
lib/iomap.c one, copies the content of a struct resource into unsigned long's
which will break on 32 bits platforms with 64 bits resources.
This fixes all definitions of pci_iomap() to use resource_size_t. I also
"fixed" the 64bits arch for consistency.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since both the IDE interface and SMC 91C111 Ethernet chip are on-board
devices, not SOC devices, move the platform device registration form the
common to the board specific code.
While at it, remove semicolon (which didn't break compilation only by
chance) from the AU1XXX_ATA_DDMA_REQ macro and do some renaming:
- change 'au1200_ide0_' variable name prefix to the mere 'ide_';
- change 'smc91x_' variable name prefix to 'smc91c111_' since that's the
name of the chip used on the boards;
- drop 'AU1XXX_' prefix from the names of macros describing IDE and Ethernet
on-board devices;
- change 'SMC91111_' to 'SMC91C111_', change 'IRQ' to 'INT' in the names of
the macros describing the Ethernet chip for consistency with the IDE
macros;
- change 'ATA_' to 'IDE_' and 'OFFSET' to 'SHIFT' (since this value is
indeed a shift count) in the names of the macros describing the IDE
interface.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pb1200 does have SMC 91C111 Ethernet chip on board but the platform code
did not register it, so one couldn't mount NFS...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The on-board SMC 91C111 chip only decodes 16 bytes of memory (obviously, it
can not decode a whole megabyte starting from address 0x19000300).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Do not initialize res->parent for platform device.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Do not use non-standard I/O accessors, such as reg_rd08, etc.
* Kill unnecessary wbflush()
* Kill tx4938_mips.h
* Kill unnecessary includes
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is a board-independent TXx9 gpio API implementation using gpiolib.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch unexports the null_perf_irq() symbol, and simultaneously
makes this function static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No users for the rtc_mips_set_time() routine exist outside of the
core kernel code. Therefore, EXPORT_SYMBOL(rtc_mips_set_time) is
useless, and this patch removes it.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
No users for the copy_from_user_page() routine exist outside of the
core kernel code. Therefore, EXPORT_SYMBOL(copy_from_user_page) is
useless, and this patch removes it.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The copy_to_user_page() function is called only in the core kernel
code. Therefore, there is no need to export it. This patch removes
EXPORT_SYMBOL(copy_to_user_page).
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The copy_user_highpage() routine has no users outside of the
core kernel code, so exporting this symbol is pointless.
This patch removes EXPORT_SYMBOL(copy_user_highpage).
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the code registering the Alchemy UART platform devices from
drivers/serial/ to its proper place, into the Alchemy platform code. Fix
the related Kconfig entry, while at it...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Go thru the Alchemy code and hunt down every unneeded #include, #define, and
extern (some of which refer to already long dead functions).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The following variables defined in arch/mips/mips-boards/malta/malta_int.c
can become static: msc_irqmap[], msc_nr_irqs, msc_eicirqmap[], and
msc_nr_eicirqs. This patch makes them static.
Successfully build-tested using default configs for Malta, Atlas
and SEAD boards.
Runtime test successfully performed by booting the Malta 4Kc board
up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The array standard_io_resources[] needs not to be exposed in the kernel
global namespace. This patch makes it static.
Successfully build-tested using default configs for Malta, Atlas
and SEAD boards.
Runtime test successfully performed by booting the Malta 4Kc board
up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There is no need for the plat_perf_setup() function to be global,
so make it static.
Successfully build-tested using default configs for Malta, Atlas
and SEAD boards.
Runtime test successfully performed by booting the Malta 4Kc board
up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Neither the mdesc[] array nor the prom_getmdesc() function need to
be global. This patch makes them static.
Successfully build-tested using default configs for Malta, Atlas
and SEAD boards.
Runtime test successfully performed by booting the Malta 4Kc board
up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change makes the needlessly global function mips_ejtag_setup() static.
Successfully build-tested using default configs for Malta, Atlas
and SEAD boards.
Runtime test successfully performed by booting the Malta 4Kc board
up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change makes the needlessly global function mips_nmi_setup() static.
Successfully build-tested using default configs for Malta, Atlas
and SEAD boards.
Runtime test successfully performed by booting the Malta 4Kc board
up to the shell prompt.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the commit 91a2fcc886 ([MIPS]
Consolidate all variants of MIPS cp0 timer interrupt handlers) removed the
Alchemy specific timer handler, 'r4k_offset' and 'r4k_cur' variables became
practically useless, so get rid of them at last, renaming cal_r4off()
function into calc_clock() and making it return CPU frequency. Also, make
'no_au1xxx_32khz' variable static...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Defer the unmasking of the count/compare interrupt (IRQ5) till the
clockevent driver initialization:
- only enable the cascaded IRQs 0 thru 4 in arch_init_irq(); kill the
ALLINTS macro -- this change is blessed by AMD as I saw it in their own
patch; :-)
- do not force IRQ5 enabled in plat_time_init() if PM is enabled and there's
no 32 KHz crystal.
Update the copyrights (taking into account my prior changes), also removing
Pete Popov's old email...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Slightly tacky, but there is a precedent in the sparc archirecture code.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It is not being used by Malta and shouldn't be needed for MIPSsim.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fold the SB-1 specific implementation of clear_page/copy_page in the
generic version, and rewrite that one in tlbex style. The immediate
benefits:
- It converts the compile-time workaround for SB-1 pass 1 prefetches
to a more efficient run-time check.
- It allows adjustment of loop unfolling, which helps to reduce the
number of redundant cdex cache ops.
- It fixes some esoteric cornercases (the cache line length calculations
can go wrong, and support for 64k pages without prefetch instructions
will overflow the addiu immediate).
- Somewhat better guesses of "good" prefetch values.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add the ability to pass comments into asm-offsets.h by generating asm
output like
-># comment line
Mips needs this feature to preserve the comments that are in
asm-mips/asm-offsets.h right now.
Then remove the special handling for mips from Kbuild and convert mips to use
the new string to include the comments.
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
The header files for the Pb1200/DBAu1200 boards have wrong definition for the
IDE interface's decoded range length -- it should be 512 bytes according to
what the IDE driver does. In addition, the IDE platform device claims 1 byte
too many for its memory resource -- fix the platform code and the IDE driver
in accordance.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
AFAICT pm_send_all is a nop when noone uses pm_register...
Hmm.. can we just force CONFIG_PM_LEGACY=n, and see what happens?
Or maybe this is better idea? It may break build somewhere, but it
should be easy to fix... (it builds here, i386 and x86-64).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
flush_cache_vmap / flush_cache_vunmap were calling flush_cache_all which -
having been deprecated - turned into a nop ...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Building UP kernel with KGDB enabled produces the following errors and warning
(fatal due to -Werror in arch/mips/kernel/Makefile):
In file included from arch/mips/kernel/gdb-stub.c:142:
include/asm/smp.h:25:1: "raw_smp_processor_id" redefined
In file included from include/linux/sched.h:69,
from arch/mips/kernel/gdb-stub.c:126:
include/linux/smp.h:88:1: this is the location of the previous definition
In file included from arch/mips/kernel/gdb-stub.c:142:
include/asm/smp.h:62: error: redefinition of 'smp_send_reschedule'
include/linux/smp.h:102: error: previous definition of 'smp_send_reschedule' was here
include/asm/smp.h: In function `smp_send_reschedule':
include/asm/smp.h:65: error: dereferencing pointer to incomplete type
arch/mips/kernel/gdb-stub.c: At top level:
arch/mips/kernel/gdb-stub.c:660: warning: 'kgdb_wait' defined but not used
Fix the errors by not directly including <asm/smp.h> (which is already included
by <linux/smp.h>) and the warning by enclosing kgdb_wait() in #ifdef CONFIG_SMP.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes the compilation of the Au1000 XSS1500
board setup and irqmap code.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Work around the CPU clock miscalculation on Au1000DA/HA/HB due the
sys_cpupll register being write-only, i.e. actually do what the comment
before cal_r4off() function advertised for years but the code failed at.
This is achieved by just giving user a chance to define the clock
explicitly in the board config. via CONFIG_SOC_AU1000_FREQUENCY option,
defaulting to 396 MHz if the option is not given...
The patch is based on the AMD's big unpublished patch, the issue seems to
be an undocumented errata (or feature :-)...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Early 4KEc were MIPS32r1 and therefore need some love to get a TLB
refill handler.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- removed check for enable HT-PCI bridges, because some CFE version
init only the needed one and scanning works even with disabled HT
links
- implemented I/O access behind HT PCI busses
- fixed pci_map for IO resource behind PCI bridge
Tested with E100 and Tulip driver.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Check whether gcc supports -mr10-cache-barrier=1 and issue a cleaner
error message if not. This option is needed to build working SGI IP28
kernels.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
And while at it, make it a little cleaner. Issue originally reported by
Tiejun Chen (tiejun.chen@windriver.com).
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With KBUILD_DEFCONFIG we don't have to ship a second copy of ip22_defconfig.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows a 48Hz clock to be selected on Malta and other systems. Note
this not normally a sensible option as it results in rather high latencies
for some kernel stuff.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some of these are architecturally required for R2 processors so lets try
to be bit closer to the real thing. This also provides access to the
CPU cycle timer, even on multiprocessors. In that aspect its currently
bug compatible to what would happen on a R2-based SMP.
Signed-off-by: Chris Dearman <chris@mips.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
0 is a valid device id (DSCR_CMD0_UART0_TX), so we can't use it to mark
an empty entry in the device table. Use ~0 instead and search for id ~0
when looking for a free entry.
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Switch the BCM47XX code to the new SPROM data structure now that the old
one has been removed.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The MIPS version of pcibios_enalbe_resources did not have the fixes
from ed6d14f976 yet which under circumstances
similar to x86 might result in failures.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Two files were omitted from the recent removal of the qemu platform.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch enables the system calls timerfd_create(), timerfd_settime()
and timerfd_gettime() for MIPS architecture.
Please see the following Bugzilla entry for more details:
http://bugzilla.kernel.org/show_bug.cgi?id=10038
This was tested using a Malta 4Kc board in both little-endian and
big-endian modes. The unit test program is available from the URL
above.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
[Ralf: Added N64, N32 and O32 bits on 64-bit kernels.]
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fix type mismatch warnings for 64-bit kernel builds which trigger -Werror.
The problem affects only SB-1 kernels with CONFIG_SIBYTE_DMA_PAGEOPS
enabled.
Signed-off-by: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
kmap_coherent will only work correctly if the page it is called on is
not marked dirty. If it's dirty the kernel address of the page should
be used instead of a temporary mapping.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Properly acknowledge RM7K and RM9K interrupts. Before this, interrupts were
permanently masked after their first occurrence, making them non-functional.
Signed-off-by: Thomas Koeller <thomas.koeller@baslerweb.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
So far flush_cache_range() did't consider the I-cache largely because it
did rarely ever matter to real world code. This was working primarily
because normally code and data are don't share the same pages - with the
exception of MIPS16 code which uses address constants embedded between
the code. The following sequence of events may break the code:
o MIPS16 executable being loaded
o dynamic linker relocates the address constants embedded into the code:
o Uses mprotect(2) to make code pages PROT_READ|PROT_WRITE
o Performs the actual relocations by writing to the pages which likely
are COW. Because no PROT_EXEC is set I-cache coherence will not be
considered.
o Uses mprotect(2) to switch code pages back to PROT_READ|PROT_EXEC.
This results in a call to flush_cache_range() which also does not
consider I-caches.
o => executing the page just having been relocated may now result in the
I-cache getting refilled with stale data from memory.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
There are some places left in mips, that lookup task in initial namespace,
while the code doing so gets the pid from the user space and thus must
treat it as virtual.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Add path_put() functions for releasing a reference to the dentry and
vfsmount of a struct path in the right order
* Switch from path_release(nd) to path_put(&nd->path)
* Rename dput_path() to path_put_conditional()
[akpm@linux-foundation.org: fix cifs]
Signed-off-by: Jan Blunck <jblunck@suse.de>
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: <linux-fsdevel@vger.kernel.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Steven French <sfrench@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
David Daney