DM RAID: Add message/status support for changing sync action
This patch adds a message interface to dm-raid to allow the user to more
finely control the sync actions being performed by the MD driver. This
gives the user the ability to initiate "check" and "repair" (i.e. scrubbing).
Two additional fields have been appended to the status output to provide more
information about the type of sync action occurring and the results of those
actions, specifically: <sync_action> and <mismatch_cnt>. These new fields
will always be populated. This is essentially the device-mapper way of doing
what MD controls through the 'sync_action' sysfs file and shows through the
'mismatch_cnt' sysfs file.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD: Export 'md_reap_sync_thread' function
Make 'md_reap_sync_thread' available to other files, specifically dm-raid.c.
- rename reap_sync_thread to md_reap_sync_thread
- move the fn after md_check_recovery to match md.h declaration placement
- export md_reap_sync_thread
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
read-only arrays should stay that way as much as possible.
Updating the metadata - which could be triggered by a re-add
while assembling the array metadata - should be avoided.
Signed-off-by: NeilBrown <neilb@suse.de>
When assembling an array incrementally we might want to make
it device available when "enough" devices are present, but maybe
not "all" devices are present.
If the remaining devices appear before the array is actually used,
they should be added transparently.
We do this by using the "read-auto" mode where the array acts like
it is read-only until a write request arrives.
Current an add-device request switches a read-auto array to active.
This means that only one device can be added after the array is first
made read-auto. This isn't a problem for RAID5, but is not ideal for
RAID6 or RAID10.
Also we don't really want to switch the array to read-auto at all
when re-adding a device as this doesn't really imply any change.
So:
- remove the "md_update_sb()" call from add_new_disk(). This isn't
really needed as just adding a disk doesn't require a metadata
update. Instead, just set MD_CHANGE_DEVS. This will effect a
metadata update soon enough, once the array is not read-only.
- Allow the ADD_NEW_DISK ioctl to succeed without activating a
read-auto array, providing the MD_DISK_SYNC flag is set.
In this case, the device will be rejected if it cannot be added
with the correct device number, or has an incorrect event count.
- Teach remove_and_add_spares() to be careful about adding spares
when the array is read-only (or read-mostly) - only add devices
that are thought to be in-sync, and only do it if the array is
in-sync itself.
- In md_check_recovery, use remove_and_add_spares in the read-only
case, rather than open coding just the 'remove' part of it.
Reported-by: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NeilBrown <neilb@suse.de>
When an array is assembled incrementally with mdadm -I -R
and the array switches to "active" mode, md starts a recovery.
If the array was clean, the "fullsync" flag will be 0. Skip
the full recovery in this case, as RAID1 does (the code was
actually copied from the sync_request() method of RAID1).
Signed-off-by: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NeilBrown <neilb@suse.de>
If we write to a known-bad-block it will be flags as having
a ReadError by analyse_stripe, but the write will proceed anyway
(as it should). Then the read-error handling will kick in an
write again, then re-read.
We don't need that 'write-again', so set R5_ReWrite so it looks like
it has already been done. Then we will just get the re-read, which we
want.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
As the function call is the most expensive of these tests it should be
done later in the chain so that it can be avoided in some cases.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The value returned by test_and_set_bit_le() drivers/md/bitmap.c is not used.
So just use set_bit_le(). The same goes for test_and_clear_bit_le().
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Neil Brown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
If a fail device or a spare is removed from an array, there is
not need to make the array 'active'. If/when the array does become
active for some other reason the metadata will be update to reflect
the removal.
If that never happens and the array is stopped while still read-auto,
then there is no loss in forgetting the that the device had 'failed'.
A read-only array will leave failed devices attached to
the array personality, so we need to explicitly call
remove_and_add_spares() to free it (clearing Blocked just
like we do in store_slot()).
Signed-off-by: NeilBrown <neilb@suse.de>
slot_store and remove_and_add_spares both call ->hot_remove_disk(),
but with slightly different tests and consequences, which is
at least untidy and might be buggy.
So modify remove_and_add_spaces() so that it can be asked
to remove a specific device, and call it from slot_store().
We also clear the Blocked flag to ensure that doesn't prevent
removal. The purpose of Blocked is to prevent automatic removal
by the kernel before an error is acknowledged.
If the array is read/write then user-space would have not reason
to remove a device unless it was known to be 'spare' or 'faulty' in
which it would have already cleared the Blocked flag.
If the array is read-only, the flag might still be blocked, but
there is no harm in clearing the flag for read-only arrays.
Signed-off-by: NeilBrown <neilb@suse.de>
Normally we don't even try to update the metadata if
the array is read-only. However future patches
will increase the number of things that can happen on a read-only
array, so it is safest to explicitly disable this.
Every time that mddev->ro is set to 0, either
- md_update_sb will be called again (at least if MD_CHANGE_DEVS
is set) or
- the mddev->thread is scheduled, which will also run
md_update_sb if needed.
So this is safe: if the array ever become read-write the
metadata will be updated.
Signed-off-by: NeilBrown <neilb@suse.de>
Stacked md devices reuse the bvm for the subordinate device, causing
problems...
Reported-by: Michael Balser <michael.balser@profitbricks.com>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
bch_bio_max_sectors() was checking against BIO_MAX_PAGES as if the limit
was for the total bytes in the bio, not the number of segments.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Add a new superblock version, and consolidate related defines.
Signed-off-by: Gabriel de Perthuis <g2p.code+bcache@gmail.com>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
This reverts commit 3a366e614d.
Wanlong Gao reports that it causes a kernel panic on his machine several
minutes after boot. Reverting it removes the panic.
Jens says:
"It's not quite clear why that is yet, so I think we should just revert
the commit for 3.9 final (which I'm assuming is pretty close).
The wifi is crap at the LSF hotel, so sending this email instead of
queueing up a revert and pull request."
Reported-by: Wanlong Gao <gaowanlong@cn.fujitsu.com>
Requested-by: Jens Axboe <axboe@kernel.dk>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
m68k/allmodconfig:
drivers/md/bcache/bset.c: In function ‘bset_search_tree’:
drivers/md/bcache/bset.c:727: error: implicit declaration of function ‘prefetch’
drivers/md/bcache/btree.c: In function ‘bch_btree_node_get’:
drivers/md/bcache/btree.c:933: error: implicit declaration of function ‘prefetch’
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
A recent patch to fix the dm cache target's writethrough mode extended
the bio's front_pad to include a 1056-byte struct dm_bio_details.
Writeback mode doesn't need this, so this patch reduces the
per_bio_data_size to 16 bytes in this case instead of 1096.
The dm_bio_details structure was added in "dm cache: fix writes to
cache device in writethrough mode" which fixed commit e2e74d617e ("dm
cache: fix race in writethrough implementation"). In writeback mode
we avoid allocating the writethrough-specific members of the
per_bio_data structure (the dm_bio_details structure included).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The dm-cache writethrough strategy introduced by commit e2e74d617e
("dm cache: fix race in writethrough implementation") issues a bio to
the origin device, remaps and then issues the bio to the cache device.
This more conservative in-series approach was selected to favor
correctness over performance (of the previous parallel writethrough).
However, this in-series implementation that reuses the same bio to write
both the origin and cache device didn't take into account that the block
layer's req_bio_endio() modifies a completing bio's bi_sector and
bi_size. So the new writethrough strategy needs to preserve these bio
fields, and restore them before submission to the cache device,
otherwise nothing gets written to the cache (because bi_size is 0).
This patch adds a struct dm_bio_details field to struct per_bio_data,
and uses dm_bio_record() and dm_bio_restore() to ensure the bio is
restored before reissuing to the cache device. Adding such a large
structure to the per_bio_data is not ideal but we can improve this
later, for now correctness is the important thing.
This problem initially went unnoticed because the dm-cache test-suite
uses a linear DM device for the dm-cache device's origin device.
Writethrough worked as expected because DM submits a *clone* of the
original bio, so the original bio which was reused for the cache was
never touched.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Tejun writes:
-----
This is the pull request for the earlier patchset[1] with the same
name. It's only three patches (the first one was committed to
workqueue tree) but the merge strategy is a bit involved due to the
dependencies.
* Because the conversion needs features from wq/for-3.10,
block/for-3.10/core is based on rc3, and wq/for-3.10 has conflicts
with rc3, I pulled mainline (rc5) into wq/for-3.10 to prevent those
workqueue conflicts from flaring up in block tree.
* Resolving the issue that Jan and Dave raised about debugging
requires arch-wide changes. The patchset is being worked on[2] but
it'll have to go through -mm after these changes show up in -next,
and not included in this pull request.
The three commits are located in the following git branch.
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git writeback-workqueue
Pulling it into block/for-3.10/core produces a conflict in
drivers/md/raid5.c between the following two commits.
e3620a3ad5 ("MD RAID5: Avoid accessing gendisk or queue structs when not available")
2f6db2a707 ("raid5: use bio_reset()")
The conflict is trivial - one removes an "if ()" conditional while the
other removes "rbi->bi_next = NULL" right above it. We just need to
remove both. The merged branch is available at
git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq.git block-test-merge
so that you can use it for verification. The test merge commit has
proper merge description.
While these changes are a bit of pain to route, they make code simpler
and even have, while minute, measureable performance gain[3] even on a
workload which isn't particularly favorable to showing the benefits of
this conversion.
----
Fixed up the conflict.
Conflicts:
drivers/md/raid5.c
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Commit 82a84eaf7e51ba3da0c36cbc401034a4e943492d left a return 0 in
closure_debug_init(). Whoops.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Took out some nested functions, and fixed some more checkpatch
complaints.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: linux-bcache@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
config: make ARCH=i386 allmodconfig
All error/warnings:
drivers/md/bcache/bset.c: In function 'bch_ptr_bad':
>> drivers/md/bcache/bset.c:164:2: warning: format '%li' expects argument of type 'long int', but argument 4 has type 'size_t' [-Wformat]
--
drivers/md/bcache/debug.c: In function 'bch_pbtree':
>> drivers/md/bcache/debug.c:86:4: warning: format '%li' expects argument of type 'long int', but argument 4 has type 'size_t' [-Wformat]
--
drivers/md/bcache/btree.c: In function 'bch_btree_read_done':
>> drivers/md/bcache/btree.c:245:8: warning: format '%lu' expects argument of type 'long unsigned int', but argument 4 has type 'size_t' [-Wformat]
--
drivers/md/bcache/closure.o: In function `closure_debug_init':
>> (.init.text+0x0): multiple definition of `init_module'
>> drivers/md/bcache/super.o:super.c:(.init.text+0x0): first defined here
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: Fengguang Wu <fengguang.wu@intel.com>
Cc: linux-bcache@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Does writethrough and writeback caching, handles unclean shutdown, and
has a bunch of other nifty features motivated by real world usage.
See the wiki at http://bcache.evilpiepirate.org for more.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=Rycs
-----END PGP SIGNATURE-----
Merge tag 'md-3.9-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"A few bugfixes for md
- recent regressions in raid5
- recent regressions in dmraid
- a few instances of CONFIG_MULTICORE_RAID456 linger
Several tagged for -stable"
* tag 'md-3.9-fixes' of git://neil.brown.name/md:
md: remove CONFIG_MULTICORE_RAID456 entirely
md/raid5: ensure sync and DISCARD don't happen at the same time.
MD: Prevent sysfs operations on uninitialized kobjects
MD RAID5: Avoid accessing gendisk or queue structs when not available
md/raid5: schedule_construction should abort if nothing to do.
More prep work for immutable bvecs:
A few places in the code were either open coding or using the wrong
version - fix.
After we introduce the bvec iter, it'll no longer be possible to modify
the biovec through bio_for_each_segment_all() - it doesn't increment a
pointer to the current bvec, you pass in a struct bio_vec (not a
pointer) which is updated with what the current biovec would be (taking
into account bi_bvec_done and bi_size).
So because of that it's more worthwhile to be consistent about
bio_for_each_segment()/bio_for_each_segment_all() usage.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Alexander Viro <viro@zeniv.linux.org.uk>
__bio_for_each_segment() iterates bvecs from the specified index
instead of bio->bv_idx. Currently, the only usage is to walk all the
bvecs after the bio has been advanced by specifying 0 index.
For immutable bvecs, we need to split these apart;
bio_for_each_segment() is going to have a different implementation.
This will also help document the intent of code that's using it -
bio_for_each_segment_all() is only legal to use for code that owns the
bio.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Neil Brown <neilb@suse.de>
CC: Boaz Harrosh <bharrosh@panasas.com>
This doesn't really delete any code _yet_, but once immutable bvecs are
done we can just delete the rest of the code in that loop.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
More bi_idx removal. This code was just open coding bio_clone(). This
could probably be further improved by using bio_advance() instead of
skipping over null pages, but that'd be a larger rework.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
Had to shuffle the code around a bit (where bi_rw and bi_end_io were
set), but shouldn't really be anything tricky here
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
More prep work for immutable bio vecs, mainly getting rid of references
to bi_idx.
bio_reset was being open coded in a few places. The one in sync_request
was a bit nontrivial to convert, so could use some extra eyeballs.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
Acked-by: NeilBrown <neilb@suse.de>
Random cleanup - this code was duplicated and it's not really specific
to md.
Also added the ability to return the actual error code.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
For immutable bvecs, all bi_idx usage needs to be audited - so here
we're removing all the unnecessary uses.
Most of these are places where it was being initialized on a bio that
was just allocated, a few others are conversions to standard macros.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
In the current code bio_split() won't be seeing partially completed bios
so this doesn't change any behaviour, but this makes the code a bit
clearer as to what bio_split() actually requires.
The immediate purpose of the patch is removing unnecessary bi_idx
references, but the end goal is to allow partial completed bios to be
submitted, which along with immutable biovecs enables effecient bio
splitting.
Some of the callers were (double) checking that bios could be split, so
update their checks too.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Lars Ellenberg <drbd-dev@lists.linbit.com>
CC: Neil Brown <neilb@suse.de>
CC: Martin K. Petersen <martin.petersen@oracle.com>
Bunch of places in the code weren't using it where they could be -
this'll reduce the size of the patch that puts bi_sector/bi_size/bi_idx
into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: "Ed L. Cashin" <ecashin@coraid.com>
CC: Nick Piggin <npiggin@kernel.dk>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jim Paris <jim@jtan.com>
CC: Geoff Levand <geoff@infradead.org>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Ed Cashin <ecashin@coraid.com>
Just a little convenience macro - main reason to add it now is preparing
for immutable bio vecs, it'll reduce the size of the patch that puts
bi_sector/bi_size/bi_idx into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Lars Ellenberg <drbd-dev@lists.linbit.com>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Martin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux-s390@vger.kernel.org
CC: Chris Mason <chris.mason@fusionio.com>
CC: Steven Whitehouse <swhiteho@redhat.com>
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
When reading the dm cache metadata from disk, ignore the policy hints
unless they were generated by the same major version number of the same
policy module.
The hints are considered to be private data belonging to the specific
module that generated them and there is no requirement for them to make
sense to different versions of the policy that generated them.
Policy modules are all required to work fine if no previous hints are
supplied (or if existing hints are lost).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Separate dm cache policy version string into 3 unsigned numbers
corresponding to major, minor and patchlevel and store them at the end
of the on-disk metadata so we know which version of the policy generated
the hints in case a future version wants to use them differently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
We have found a race in the optimisation used in the dm cache
writethrough implementation. Currently, dm core sends the cache target
two bios, one for the origin device and one for the cache device and
these are processed in parallel. This patch avoids the race by
changing the code back to a simpler (slower) implementation which
processes the two writes in series, one after the other, until we can
develop a complete fix for the problem.
When the cache is in writethrough mode it needs to send WRITE bios to
both the origin and cache devices.
Previously we've been implementing this by having dm core query the
cache target on every write to find out how many copies of the bio it
wants. The cache will ask for two bios if the block is in the cache,
and one otherwise.
Then main problem with this is it's racey. At the time this check is
made the bio hasn't yet been submitted and so isn't being taken into
account when quiescing a block for migration (promotion or demotion).
This means a single bio may be submitted when two were needed because
the block has since been promoted to the cache (catastrophic), or two
bios where only one is needed (harmless).
I really don't want to start entering bios into the quiescing system
(deferred_set) in the get_num_write_bios callback. Instead this patch
simplifies things; only one bio is submitted by the core, this is
first written to the origin and then the cache device in series.
Obviously this will have a latency impact.
deferred_writethrough_bios is introduced to record bios that must be
later issued to the cache device from the worker thread. This deferred
submission, after the origin bio completes, is required given that we're
in interrupt context (writethrough_endio).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When writing the dirty bitset to the metadata device on a clean
shutdown, clear the dirty bits. Previously they were left indicating
the cache was dirty. This led to confusion about whether there really
was dirty data in the cache or not. (This was a harmless bug.)
Reported-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If the cache policy's config values are not able to be set we must
set the policy to NULL after destroying it in create_cache_policy()
so we don't attempt to destroy it a second time later.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Return error if cache_create() fails.
A missing return check made cache_ctr continue even after an error in
cache_create() resulting in the cache object being destroyed. So a
simple failure like an odd number of cache policy config value arguments
would result in an oops.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Squash various 32bit link errors.
>> on i386:
>> drivers/built-in.o: In function `is_discarded_oblock':
>> dm-cache-target.c:(.text+0x1ea28e): undefined reference to `__udivdi3'
...
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A deadlock was found in the prefetch code in the dm verity map
function. This patch fixes this by transferring the prefetch
to a worker thread and skipping it completely if kmalloc fails.
If generic_make_request is called recursively, it queues the I/O
request on the current->bio_list without making the I/O request
and returns. The routine making the recursive call cannot wait
for the I/O to complete.
The deadlock occurs when one thread grabs the bufio_client
mutex and waits for an I/O to complete but the I/O is queued
on another thread's current->bio_list and is waiting to get
the mutex held by the first thread.
The fix recognises that prefetching is not essential. If memory
can be allocated, it queues the prefetch request to the worker thread,
but if not, it does nothing.
Signed-off-by: Paul Taysom <taysom@chromium.org>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@kernel.org
Fix a discard granularity calculation to work for non power of 2 block sizes.
In order for thinp to passdown discard bios to the underlying data
device, the data device must have a discard granularity that is a
factor of the thinp block size. Originally this check was done by
using bitops since the block_size was known to be a power of two.
Introduced by commit f13945d757
("dm thin: support a non power of 2 discard_granularity").
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a bug in dm_btree_remove that could leave leaf values with incorrect
reference counts. The effect of this was that removal of a shared block
could result in the space maps thinking the block was no longer used.
More concretely, if you have a thin device and a snapshot of it, sending
a discard to a shared region of the thin could corrupt the snapshot.
Thinp uses a 2-level nested btree to store it's mappings. This first
level is indexed by thin device, and the second level by logical
block.
Often when we're removing an entry in this mapping tree we need to
rebalance nodes, which can involve shadowing them, possibly creating a
copy if the block is shared. If we do create a copy then children of
that node need to have their reference counts incremented. In this
way reference counts percolate down the tree as shared trees diverge.
The rebalance functions were incrementing the children at the
appropriate time, but they were always assuming the children were
internal nodes. This meant the leaf values (in our case packed
block/flags entries) were not being incremented.
Cc: stable@vger.kernel.org
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Once instance of this Kconfig macro remained after commit
51acbcec6c ("md: remove
CONFIG_MULTICORE_RAID456"). Remove that one too. And, while we're at it,
also remove it from the defconfig files that carry it.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: NeilBrown <neilb@suse.de>
A number of problems can occur due to races between
resync/recovery and discard.
- if sync_request calls handle_stripe() while a discard is
happening on the stripe, it might call handle_stripe_clean_event
before all of the individual discard requests have completed
(so some devices are still locked, but not all).
Since commit ca64cae960
md/raid5: Make sure we clear R5_Discard when discard is finished.
this will cause R5_Discard to be cleared for the parity device,
so handle_stripe_clean_event() will not be called when the other
devices do become unlocked, so their ->written will not be cleared.
This ultimately leads to a WARN_ON in init_stripe and a lock-up.
- If handle_stripe_clean_event() does clear R5_UPTODATE at an awkward
time for resync, it can lead to s->uptodate being less than disks
in handle_parity_checks5(), which triggers a BUG (because it is
one).
So:
- keep R5_Discard on the parity device until all other devices have
completed their discard request
- make sure we don't try to have a 'discard' and a 'sync' action at
the same time.
This involves a new stripe flag to we know when a 'discard' is
happening, and the use of R5_Overlap on the parity disk so when a
discard is wanted while a sync is active, so we know to wake up
the discard at the appropriate time.
Discard support for RAID5 was added in 3.7, so this is suitable for
any -stable kernel since 3.7.
Cc: stable@vger.kernel.org (v3.7+)
Reported-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Tested-by: Jes Sorensen <Jes.Sorensen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD: Prevent sysfs operations on uninitialized kobjects
Device-mapper does not use sysfs; but when device-mapper is leveraging
MD's RAID personalities, MD sometimes attempts to update sysfs. This
patch adds checks for 'mddev-kobj.sd' in sysfs_[un]link_rdev to ensure
it is about to operate on something valid. This patch also checks for
'mddev->kobj.sd' before calling 'sysfs_notify' in 'remove_and_add_spares'.
Although 'sysfs_notify' already makes this check, doing so in
'remove_and_add_spares' prevents an additional mutex operation.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID5: Fix kernel oops when RAID4/5/6 is used via device-mapper
Commit a9add5d (v3.8-rc1) added blktrace calls to the RAID4/5/6 driver.
However, when device-mapper is used to create RAID4/5/6 arrays, the
mddev->gendisk and mddev->queue fields are not setup. Therefore, calling
things like trace_block_bio_remap will cause a kernel oops. This patch
conditionalizes those calls on whether the proper fields exist to make
the calls. (Device-mapper will call trace_block_bio_remap on its own.)
This patch is suitable for the 3.8.y stable kernel.
Cc: stable@vger.kernel.org (v3.8+)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Since commit 1ed850f356
md/raid5: make sure to_read and to_write never go negative.
It has been possible for handle_stripe_dirtying to be called
when there isn't actually any work to do.
It then calls schedule_reconstruction() which will set R5_LOCKED
on the parity block(s) even when nothing else is happening.
This then causes problems in do_release_stripe().
So add checks to schedule_reconstruction() so that if it doesn't
find anything to do, it just aborts.
This bug was introduced in v3.7, so the patch is suitable
for -stable kernels since then.
Cc: stable@vger.kernel.org (v3.7+)
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
mostly little bugfixes.
Only "feature" is a new RAID10 layout which slightly
improves the number of sets of devices that can concurrently
fail, without data loss.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=YdVD
-----END PGP SIGNATURE-----
Merge tag 'md-3.9' of git://neil.brown.name/md
Pull md updates from NeilBrown:
"Mostly little bugfixes.
Only "feature" is a new RAID10 layout which slightly improves the
number of sets of devices that can concurrently fail, without data
loss."
* tag 'md-3.9' of git://neil.brown.name/md:
md: expedite metadata update when switching read-auto -> active
md: remove CONFIG_MULTICORE_RAID456
md/raid1,raid10: fix deadlock with freeze_array()
md/raid0: improve error message when converting RAID4-with-spares to RAID0
md: raid0: fix error return from create_stripe_zones.
md: fix two bugs when attempting to resize RAID0 array.
DM RAID: Add support for MD's RAID10 "far" and "offset" algorithms
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 2)
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 1)
MD RAID10: Minor non-functional code changes
md: raid1,10: Handle REQ_WRITE_SAME flag in write bios
md: protect against crash upon fsync on ro array
A simple cache policy that writes back all data to the origin.
This is used to decommission a dm cache by emptying it.
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A cache policy that uses a multiqueue ordered by recent hit
count to select which blocks should be promoted and demoted.
This is meant to be a general purpose policy. It prioritises
reads over writes.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a target that allows a fast device such as an SSD to be used as a
cache for a slower device such as a disk.
A plug-in architecture was chosen so that the decisions about which data
to migrate and when are delegated to interchangeable tunable policy
modules. The first general purpose module we have developed, called
"mq" (multiqueue), follows in the next patch. Other modules are
under development.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Heinz Mauelshagen <mauelshagen@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch takes advantage of the new bio-prison interface where the
memory is now passed in rather than using a mempool in bio-prison.
This allows the map function to avoid performing potentially-blocking
allocations that could lead to deadlocks: We want to avoid the cell
allocation that is done in bio_detain.
(The potential for mempool deadlocks still remains in other functions
that use bio_detain.)
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Change the dm_bio_prison interface so that instead of allocating memory
internally, dm_bio_detain is supplied with a pre-allocated cell each
time it is called.
This enables a subsequent patch to move the allocation of the struct
dm_bio_prison_cell outside the thin target's mapping function so it can
no longer block there.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add dm_btree_walk to iterate through the contents of a btree.
This will be used by the dm cache target.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a num_write_bios function to struct target.
If an instance of a target sets this, it will be queried before the
target's mapping function is called on a write bio, and the response
controls the number of copies of the write bio that the target will
receive.
This provides a convenient way for a target to send the same data to
more than one device. The new cache target uses this in writethrough
mode, to send the data both to the cache and the backing device.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch allows the administrator to reduce the rate at which kcopyd
issues I/O.
Each module that uses kcopyd acquires a throttle parameter that can be
set in /sys/module/*/parameters.
We maintain a history of kcopyd usage by each module in the variables
io_period and total_period in struct dm_kcopyd_throttle. The actual
kcopyd activity is calculated as a percentage of time equal to
"(100 * io_period / total_period)". This is compared with the user-defined
throttle percentage threshold and if it is exceeded, we sleep.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch introduces enhanced message support that allows the
device-mapper core to recognise messages that are common to all devices,
and for messages to return data to userspace.
Core messages are processed by the function "message_for_md". If the
device mapper doesn't support the message, it is passed to the target
driver.
If the message returns data, the kernel sets the flag
DM_MESSAGE_OUT_FLAG.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Device-mapper ioctls receive and send data in a buffer supplied
by userspace. The buffer has two parts. The first part contains
a 'struct dm_ioctl' and has a fixed size. The second part depends
on the ioctl and has a variable size.
This patch recognises the specific ioctls that do not use the variable
part of the buffer and skips allocating memory for it.
In particular, when a device is suspended and a resume ioctl is sent,
this now avoid memory allocation completely.
The variable "struct dm_ioctl tmp" is moved from the function
copy_params to its caller ctl_ioctl and renamed to param_kernel.
It is used directly when the ioctl function doesn't need any arguments.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch introduces flags for each ioctl function.
So far, one flag is defined, IOCTL_FLAGS_NO_PARAMS. It is set if the
function processing the ioctl doesn't take or produce any parameters in
the section of the data buffer that has a variable size.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch merges io_pool and tio_pool into io_pool and cleans up
related functions.
Though device-mapper used to have 2 pools of objects for each dm device,
the use of bioset frontbad for per-bio data has shrunk the number of
pools to 1 for both bio-based and request-based device types.
(See c0820cf5 "dm: introduce per_bio_data" and
94818742 "dm: Use bioset's front_pad for dm_rq_clone_bio_info")
So dm no longer has to maintain 2 different pointers.
No functional changes.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove _rq_bio_info_cache, which is no longer used.
No functional changes.
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm_calculate_queue_limits will first reset the provided limits to
defaults using blk_set_stacking_limits; whereby defeating the purpose of
retaining the original live table's limits -- as was intended via commit
3ae7065616 ("dm: retain table limits when
swapping to new table with no devices").
Fix this improper limits initialization (in the no data devices case) by
avoiding the call to dm_calculate_queue_limits.
[patch header revised by Mike Snitzer]
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.6+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add module aliases so that autoloading works correctly if the user
tries to activate "snapshot-origin" or "snapshot-merge" targets.
Reference: https://bugzilla.redhat.com/889973
Reported-by: Chao Yang <chyang@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Mark some constant parameters constant in some dm-btree functions.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename functions involved in splitting and cloning bios.
The sequence of functions is now:
(1) __split_and_process* - entry point that selects the processing strategy
(2) __send* - prepare the details for each bio needed and loop through them
(3) __clone_and_map* - creates a clone and maps it
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use 'bio' in the name of variables and functions that deal with
bios rather than 'request' to avoid confusion with the normal
block layer use of 'request'.
No functional changes.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the no-longer-used struct bio_set argument from clone_bio and split_bvec.
Use tio->ti in __map_bio() instead of passing in ti.
Factor out some code for setting up cloned bios.
Take target_request_nr as a parameter to alloc_tio().
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use block_size_is_power_of_two() rather than checking
sectors_per_block_shift directly. Also introduce local pool variable in
get_bio_block() to eliminate redundant tc->pool dereferences.
No functional change.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use WRITE_FLUSH instead of REQ_FLUSH for submitted requests to make it
consistent with the rest of the kernel. There is no functional change.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If allocation fails, the local var *t is not used any more after kfree.
Don't need to reset it to NULL. Remove the unnecesary NULL set here.
Signed-off-by: Wang Sheng-Hui <shhuiw@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support a non-power-of-2 discard granularity in dm-thin, now that the block
layer supports this(via 8dd2cb7e88 "block:
discard granularity might not be power of 2" and
59771079c1 "blk: avoid divide-by-zero with zero
discard granularity").
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Avoid returning a truncated table or status string instead of setting
the DM_BUFFER_FULL_FLAG when the last target of a table fills the
buffer.
When processing a table or status request, the function retrieve_status
calls ti->type->status. If ti->type->status returns non-zero,
retrieve_status assumes that the buffer overflowed and sets
DM_BUFFER_FULL_FLAG.
However, targets don't return non-zero values from their status method
on overflow. Most targets returns always zero.
If a buffer overflow happens in a target that is not the last in the
table, it gets noticed during the next iteration of the loop in
retrieve_status; but if a buffer overflow happens in the last target, it
goes unnoticed and erroneously truncated data is returned.
In the current code, the targets behave in the following way:
* dm-crypt returns -ENOMEM if there is not enough space to store the
key, but it returns 0 on all other overflows.
* dm-thin returns errors from the status method if a disk error happened.
This is incorrect because retrieve_status doesn't check the error
code, it assumes that all non-zero values mean buffer overflow.
* all the other targets always return 0.
This patch changes the ti->type->status function to return void (because
most targets don't use the return code). Overflow is detected in
retrieve_status: if the status method fills up the remaining space
completely, it is assumed that buffer overflow happened.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes a regression introduced in v3.8, which causes oops
like this when dm-multipath is used:
general protection fault: 0000 [#1] SMP
RIP: 0010:[<ffffffff810fe754>] [<ffffffff810fe754>] mempool_free+0x24/0xb0
Call Trace:
<IRQ>
[<ffffffff81187417>] bio_put+0x97/0xc0
[<ffffffffa02247a5>] end_clone_bio+0x35/0x90 [dm_mod]
[<ffffffff81185efd>] bio_endio+0x1d/0x30
[<ffffffff811f03a3>] req_bio_endio.isra.51+0xa3/0xe0
[<ffffffff811f2f68>] blk_update_request+0x118/0x520
[<ffffffff811f3397>] blk_update_bidi_request+0x27/0xa0
[<ffffffff811f343c>] blk_end_bidi_request+0x2c/0x80
[<ffffffff811f34d0>] blk_end_request+0x10/0x20
[<ffffffffa000b32b>] scsi_io_completion+0xfb/0x6c0 [scsi_mod]
[<ffffffffa000107d>] scsi_finish_command+0xbd/0x120 [scsi_mod]
[<ffffffffa000b12f>] scsi_softirq_done+0x13f/0x160 [scsi_mod]
[<ffffffff811f9fd0>] blk_done_softirq+0x80/0xa0
[<ffffffff81044551>] __do_softirq+0xf1/0x250
[<ffffffff8142ee8c>] call_softirq+0x1c/0x30
[<ffffffff8100420d>] do_softirq+0x8d/0xc0
[<ffffffff81044885>] irq_exit+0xd5/0xe0
[<ffffffff8142f3e3>] do_IRQ+0x63/0xe0
[<ffffffff814257af>] common_interrupt+0x6f/0x6f
<EOI>
[<ffffffffa021737c>] srp_queuecommand+0x8c/0xcb0 [ib_srp]
[<ffffffffa0002f18>] scsi_dispatch_cmd+0x148/0x310 [scsi_mod]
[<ffffffffa000a38e>] scsi_request_fn+0x31e/0x520 [scsi_mod]
[<ffffffff811f1e57>] __blk_run_queue+0x37/0x50
[<ffffffff811f1f69>] blk_delay_work+0x29/0x40
[<ffffffff81059003>] process_one_work+0x1c3/0x5c0
[<ffffffff8105b22e>] worker_thread+0x15e/0x440
[<ffffffff8106164b>] kthread+0xdb/0xe0
[<ffffffff8142db9c>] ret_from_fork+0x7c/0xb0
The regression was introduced by the change
c0820cf5 "dm: introduce per_bio_data", where dm started to replace
bioset during table replacement.
For bio-based dm, it is good because clone bios do not exist during the
table replacement.
For request-based dm, however, (not-yet-mapped) clone bios may stay in
request queue and survive during the table replacement.
So freeing the old bioset could cause the oops in bio_put().
Since the size of front_pad may change only with bio-based dm,
it is not necessary to replace bioset for request-based dm.
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull block IO core bits from Jens Axboe:
"Below are the core block IO bits for 3.9. It was delayed a few days
since my workstation kept crashing every 2-8h after pulling it into
current -git, but turns out it is a bug in the new pstate code (divide
by zero, will report separately). In any case, it contains:
- The big cfq/blkcg update from Tejun and and Vivek.
- Additional block and writeback tracepoints from Tejun.
- Improvement of the should sort (based on queues) logic in the plug
flushing.
- _io() variants of the wait_for_completion() interface, using
io_schedule() instead of schedule() to contribute to io wait
properly.
- Various little fixes.
You'll get two trivial merge conflicts, which should be easy enough to
fix up"
Fix up the trivial conflicts due to hlist traversal cleanups (commit
b67bfe0d42ca: "hlist: drop the node parameter from iterators").
* 'for-3.9/core' of git://git.kernel.dk/linux-block: (39 commits)
block: remove redundant check to bd_openers()
block: use i_size_write() in bd_set_size()
cfq: fix lock imbalance with failed allocations
drivers/block/swim3.c: fix null pointer dereference
block: don't select PERCPU_RWSEM
block: account iowait time when waiting for completion of IO request
sched: add wait_for_completion_io[_timeout]
writeback: add more tracepoints
block: add block_{touch|dirty}_buffer tracepoint
buffer: make touch_buffer() an exported function
block: add @req to bio_{front|back}_merge tracepoints
block: add missing block_bio_complete() tracepoint
block: Remove should_sort judgement when flush blk_plug
block,elevator: use new hashtable implementation
cfq-iosched: add hierarchical cfq_group statistics
cfq-iosched: collect stats from dead cfqgs
cfq-iosched: separate out cfqg_stats_reset() from cfq_pd_reset_stats()
blkcg: make blkcg_print_blkgs() grab q locks instead of blkcg lock
block: RCU free request_queue
blkcg: implement blkg_[rw]stat_recursive_sum() and blkg_[rw]stat_merge()
...
I'm not sure why, but the hlist for each entry iterators were conceived
list_for_each_entry(pos, head, member)
The hlist ones were greedy and wanted an extra parameter:
hlist_for_each_entry(tpos, pos, head, member)
Why did they need an extra pos parameter? I'm not quite sure. Not only
they don't really need it, it also prevents the iterator from looking
exactly like the list iterator, which is unfortunate.
Besides the semantic patch, there was some manual work required:
- Fix up the actual hlist iterators in linux/list.h
- Fix up the declaration of other iterators based on the hlist ones.
- A very small amount of places were using the 'node' parameter, this
was modified to use 'obj->member' instead.
- Coccinelle didn't handle the hlist_for_each_entry_safe iterator
properly, so those had to be fixed up manually.
The semantic patch which is mostly the work of Peter Senna Tschudin is here:
@@
iterator name hlist_for_each_entry, hlist_for_each_entry_continue, hlist_for_each_entry_from, hlist_for_each_entry_rcu, hlist_for_each_entry_rcu_bh, hlist_for_each_entry_continue_rcu_bh, for_each_busy_worker, ax25_uid_for_each, ax25_for_each, inet_bind_bucket_for_each, sctp_for_each_hentry, sk_for_each, sk_for_each_rcu, sk_for_each_from, sk_for_each_safe, sk_for_each_bound, hlist_for_each_entry_safe, hlist_for_each_entry_continue_rcu, nr_neigh_for_each, nr_neigh_for_each_safe, nr_node_for_each, nr_node_for_each_safe, for_each_gfn_indirect_valid_sp, for_each_gfn_sp, for_each_host;
type T;
expression a,c,d,e;
identifier b;
statement S;
@@
-T b;
<+... when != b
(
hlist_for_each_entry(a,
- b,
c, d) S
|
hlist_for_each_entry_continue(a,
- b,
c) S
|
hlist_for_each_entry_from(a,
- b,
c) S
|
hlist_for_each_entry_rcu(a,
- b,
c, d) S
|
hlist_for_each_entry_rcu_bh(a,
- b,
c, d) S
|
hlist_for_each_entry_continue_rcu_bh(a,
- b,
c) S
|
for_each_busy_worker(a, c,
- b,
d) S
|
ax25_uid_for_each(a,
- b,
c) S
|
ax25_for_each(a,
- b,
c) S
|
inet_bind_bucket_for_each(a,
- b,
c) S
|
sctp_for_each_hentry(a,
- b,
c) S
|
sk_for_each(a,
- b,
c) S
|
sk_for_each_rcu(a,
- b,
c) S
|
sk_for_each_from
-(a, b)
+(a)
S
+ sk_for_each_from(a) S
|
sk_for_each_safe(a,
- b,
c, d) S
|
sk_for_each_bound(a,
- b,
c) S
|
hlist_for_each_entry_safe(a,
- b,
c, d, e) S
|
hlist_for_each_entry_continue_rcu(a,
- b,
c) S
|
nr_neigh_for_each(a,
- b,
c) S
|
nr_neigh_for_each_safe(a,
- b,
c, d) S
|
nr_node_for_each(a,
- b,
c) S
|
nr_node_for_each_safe(a,
- b,
c, d) S
|
- for_each_gfn_sp(a, c, d, b) S
+ for_each_gfn_sp(a, c, d) S
|
- for_each_gfn_indirect_valid_sp(a, c, d, b) S
+ for_each_gfn_indirect_valid_sp(a, c, d) S
|
for_each_host(a,
- b,
c) S
|
for_each_host_safe(a,
- b,
c, d) S
|
for_each_mesh_entry(a,
- b,
c, d) S
)
...+>
[akpm@linux-foundation.org: drop bogus change from net/ipv4/raw.c]
[akpm@linux-foundation.org: drop bogus hunk from net/ipv6/raw.c]
[akpm@linux-foundation.org: checkpatch fixes]
[akpm@linux-foundation.org: fix warnings]
[akpm@linux-foudnation.org: redo intrusive kvm changes]
Tested-by: Peter Senna Tschudin <peter.senna@gmail.com>
Acked-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Cc: Wu Fengguang <fengguang.wu@intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert to the much saner new idr interface.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
idr_destroy() can destroy idr by itself and idr_remove_all() is being
deprecated. Drop its usage.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If something has failed while the array was read-auto,
then when we switch to 'active' we need to update the metadata.
This will happen anyway but it is good to expedite it, and
also to ensure any failed device has been released by the
underlying device before we try to action the ioctl which
caused us to switch to 'active' mode.
Reported-by: Joe Lawrence <Joe.Lawrence@stratus.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This doesn't seem to actually help and we have an alternate
multi-threading approach waiting in the wings, so just get
rid of this config option and associated code.
As a bonus, we remove one use of CONFIG_EXPERIMENTAL
Cc: Dan Williams <djbw@fb.com>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull vfs pile (part one) from Al Viro:
"Assorted stuff - cleaning namei.c up a bit, fixing ->d_name/->d_parent
locking violations, etc.
The most visible changes here are death of FS_REVAL_DOT (replaced with
"has ->d_weak_revalidate()") and a new helper getting from struct file
to inode. Some bits of preparation to xattr method interface changes.
Misc patches by various people sent this cycle *and* ocfs2 fixes from
several cycles ago that should've been upstream right then.
PS: the next vfs pile will be xattr stuff."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (46 commits)
saner proc_get_inode() calling conventions
proc: avoid extra pde_put() in proc_fill_super()
fs: change return values from -EACCES to -EPERM
fs/exec.c: make bprm_mm_init() static
ocfs2/dlm: use GFP_ATOMIC inside a spin_lock
ocfs2: fix possible use-after-free with AIO
ocfs2: Fix oops in ocfs2_fast_symlink_readpage() code path
get_empty_filp()/alloc_file() leave both ->f_pos and ->f_version zero
target: writev() on single-element vector is pointless
export kernel_write(), convert open-coded instances
fs: encode_fh: return FILEID_INVALID if invalid fid_type
kill f_vfsmnt
vfs: kill FS_REVAL_DOT by adding a d_weak_revalidate dentry op
nfsd: handle vfs_getattr errors in acl protocol
switch vfs_getattr() to struct path
default SET_PERSONALITY() in linux/elf.h
ceph: prepopulate inodes only when request is aborted
d_hash_and_lookup(): export, switch open-coded instances
9p: switch v9fs_set_create_acl() to inode+fid, do it before d_instantiate()
9p: split dropping the acls from v9fs_set_create_acl()
...
When raid1/raid10 needs to fix a read error, it first drains
all pending requests by calling freeze_array().
This calls flush_pending_writes() if it needs to sleep,
but some writes may be pending in a per-process plug rather
than in the per-array request queue.
When raid1{,0}_unplug() moves the request from the per-process
plug to the per-array request queue (from which
flush_pending_writes() can flush them), it needs to wake up
freeze_array(), or freeze_array() will never flush them and so
it will block forever.
So add the requires wake_up() calls.
This bug was introduced by commit
f54a9d0e59
for raid1 and a similar commit for RAID10, and so has been present
since linux-3.6. As the bug causes a deadlock I believe this fix is
suitable for -stable.
Cc: stable@vger.kernel.org (3.6.y 3.7.y 3.8.y)
Reported-by: Tregaron Bayly <tbayly@bluehost.com>
Tested-by: Tregaron Bayly <tbayly@bluehost.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Mentioning "bad disk number -1" exposes irrelevant internal detail.
Just say they are inactive and must be removed.
Signed-off-by: NeilBrown <neilb@suse.de>
Create_stripe_zones returns an error slightly differently to
raid0_run and to raid0_takeover_*.
The error returned used by the second was wrong and an error would
result in mddev->private being set to NULL and sooner or later a
crash.
So never return NULL, return ERR_PTR(err), not NULL from
create_stripe_zones.
This bug has been present since 2.6.35 so the fix is suitable
for any kernel since then.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
You cannot resize a RAID0 array (in terms of making the devices
bigger), but the code doesn't entirely stop you.
So:
disable setting of the available size on each device for
RAID0 and Linear devices. This must not change as doing so
can change the effective layout of data.
Make sure that the size that raid0_size() reports is accurate,
but rounding devices sizes to chunk sizes. As the device sizes
cannot change now, this isn't so important, but it is best to be
safe.
Without this change:
mdadm --grow /dev/md0 -z max
mdadm --grow /dev/md0 -Z max
then read to the end of the array
can cause a BUG in a RAID0 array.
These bugs have been present ever since it became possible
to resize any device, which is a long time. So the fix is
suitable for any -stable kerenl.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add support for MD's RAID10 "far" and "offset" algorithms
Until now, dm-raid.c only supported the "near" algorthm of MD's RAID10
implementation. This patch adds support for the "far" and "offset"
algorithms, but only with the improved redundancy that is brought with
the introduction of the 'use_far_sets' bit, which shifts copied stripes
according to smaller sets vs the entire array. That is, the 17th bit
of the 'layout' variable that defines the RAID10 implementation will
always be set. (More information on how the 'layout' variable selects
the RAID10 algorithm can be found in the opening comments of
drivers/md/raid10.c.)
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 2)
This patch addresses raid arrays that have a number of devices that cannot
be evenly divided by 'far_copies'. (E.g. 5 devices, far_copies = 2) This
case must be handled differently because it causes that last set to be of
a different size than the rest of the sets. We must compute a new modulo
for this last set so that copied chunks are properly wrapped around.
Example use_far_sets=1, far_copies=2, near_copies=1, devices=5:
"far" algorithm
dev1 dev2 dev3 dev4 dev5
==== ==== ==== ==== ====
[ A B ] [ C D E ]
[ G H ] [ I J K ]
...
[ B A ] [ E C D ] --> nominal set of 2 and last set of 3
[ H G ] [ K I J ] []'s show far/offset sets
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The MD RAID10 'far' and 'offset' algorithms make copies of entire stripe
widths - copying them to a different location on the same devices after
shifting the stripe. An example layout of each follows below:
"far" algorithm
dev1 dev2 dev3 dev4 dev5 dev6
==== ==== ==== ==== ==== ====
A B C D E F
G H I J K L
...
F A B C D E --> Copy of stripe0, but shifted by 1
L G H I J K
...
"offset" algorithm
dev1 dev2 dev3 dev4 dev5 dev6
==== ==== ==== ==== ==== ====
A B C D E F
F A B C D E --> Copy of stripe0, but shifted by 1
G H I J K L
L G H I J K
...
Redundancy for these algorithms is gained by shifting the copied stripes
one device to the right. This patch proposes that array be divided into
sets of adjacent devices and when the stripe copies are shifted, they wrap
on set boundaries rather than the array size boundary. That is, for the
purposes of shifting, the copies are confined to their sets within the
array. The sets are 'near_copies * far_copies' in size.
The above "far" algorithm example would change to:
"far" algorithm
dev1 dev2 dev3 dev4 dev5 dev6
==== ==== ==== ==== ==== ====
A B C D E F
G H I J K L
...
B A D C F E --> Copy of stripe0, shifted 1, 2-dev sets
H G J I L K Dev sets are 1-2, 3-4, 5-6
...
This has the affect of improving the redundancy of the array. We can
always sustain at least one failure, but sometimes more than one can
be handled. In the first examples, the pairs of devices that CANNOT fail
together are:
(1,2) (2,3) (3,4) (4,5) (5,6) (1, 6) [40% of possible pairs]
In the example where the copies are confined to sets, the pairs of
devices that cannot fail together are:
(1,2) (3,4) (5,6) [20% of possible pairs]
We cannot simply replace the old algorithms, so the 17th bit of the 'layout'
variable is used to indicate whether we use the old or new method of computing
the shift. (This is similar to the way the 16th bit indicates whether the
"far" algorithm or the "offset" algorithm is being used.)
This patch only handles the cases where the number of total raid disks is
a multiple of 'far_copies'. A follow-on patch addresses the condition where
this is not true.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Changes include assigning 'addr' from 's' instead of 'sector' to be
consistent with the way the code does it just a few lines later and
using '%=' vs a conditional and subtraction.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Set mddev queue's max_write_same_sectors to its chunk_sector value (before
disk_stack_limits merges the underlying disk limits.) With that in place,
be sure to handle writes coming down from the block layer that have the
REQ_WRITE_SAME flag set. That flag needs to be copied into any newly cloned
write bio.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Fix the warning:
drivers/md/persistent-data/dm-transaction-manager.c:28:1: warning: "HASH_SIZE" redefined
In file included from include/linux/elevator.h:5,
from include/linux/blkdev.h:216,
from drivers/md/persistent-data/dm-block-manager.h:11,
from drivers/md/persistent-data/dm-transaction-manager.h:10,
from drivers/md/persistent-data/dm-transaction-manager.c:6:
include/linux/hashtable.h:22:1: warning: this is the location of the previous definition
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If an fsync occurs on a read-only array, we need to send a
completion for the IO and may not increment the active IO count.
Otherwise, we hit a bug trace and can't stop the MD array anymore.
By advice of Christoph Hellwig we return success upon a flush
request but we return -EROFS for other writes.
We detect flush requests by checking if the bio has zero sectors.
This patch is suitable to any -stable kernel to which it applies.
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Reported-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Paul Menzel <paulepanter@users.sourceforge.net>
Signed-off-by: NeilBrown <neilb@suse.de>
support.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=qtaF
-----END PGP SIGNATURE-----
Merge tag 'dm-3.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull more device-mapper fixes from Alasdair G Kergon:
"A fix for stacked dm thin devices and a fix for the new dm WRITE SAME
support."
* tag 'dm-3.8-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm: fix write same requests counting
dm thin: fix queue limits stacking
When processing write same requests, fix dm to send the configured
number of WRITE SAME requests to the target rather than the number of
discards, which is not always the same.
Device-mapper WRITE SAME support was introduced by commit
23508a96cd ("dm: add WRITE SAME support").
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
thin_io_hints() is blindly copying the queue limits from the thin-pool
which can lead to incorrect limits being set. The fix here simply
deletes the thin_io_hints() hook which leaves the existing stacking
infrastructure to set the limits correctly.
When a thin-pool uses an MD device for the data device a thin device
from the thin-pool must respect MD's constraints about disallowing a bio
from spanning multiple chunks. Otherwise we can see problems. If the raid0
chunksize is 1152K and thin-pool chunksize is 256K I see the following
md/raid0 error (with extra debug tracing added to thin_endio) when
mkfs.xfs is executed against the thin device:
md/raid0:md99: make_request bug: can't convert block across chunks or bigger than 1152k 6688 127
device-mapper: thin: bio sector=2080 err=-5 bi_size=130560 bi_rw=17 bi_vcnt=32 bi_idx=0
This extra DM debugging shows that the failing bio is spanning across
the first and second logical 1152K chunk (sector 2080 + 255 takes the
bio beyond the first chunk's boundary of sector 2304). So the bio
splitting that DM is doing clearly isn't respecting the MD limits.
max_hw_sectors_kb is 127 for both the thin-pool and thin device
(queue_max_hw_sectors returns 255 so we'll excuse sysfs's lack of
precision). So this explains why bi_size is 130560.
But the thin device's max_hw_sectors_kb should be 4 (PAGE_SIZE) given
that it doesn't have a .merge function (for bio_add_page to consult
indirectly via dm_merge_bvec) yet the thin-pool does sit above an MD
device that has a compulsory merge_bvec_fn. This scenario is exactly
why DM must resort to sending single PAGE_SIZE bios to the underlying
layer. Some additional context for this is available in the header for
commit 8cbeb67a ("dm: avoid unsupported spanning of md stripe boundaries").
Long story short, the reason a thin device doesn't properly get
configured to have a max_hw_sectors_kb of 4 (PAGE_SIZE) is that
thin_io_hints() is blindly copying the queue limits from the thin-pool
device directly to the thin device's queue limits.
Fix this by eliminating thin_io_hints. Doing so is safe because the
block layer's queue limits stacking already enables the upper level thin
device to inherit the thin-pool device's discard and minimum_io_size and
optimal_io_size limits that get set in pool_io_hints. But avoiding the
queue limits copy allows the thin and thin-pool limits to be different
where it is important, namely max_hw_sectors_kb.
Reported-by: Daniel Browning <db@kavod.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Before attempting to activate a RAID array, it is checked for sufficient
redundancy. That is, we make sure that there are not too many failed
devices - or devices specified for rebuild - to undermine our ability to
activate the array. The current code performs this check twice - once to
ensure there were not too many devices specified for rebuild by the user
('validate_rebuild_devices') and again after possibly experiencing a failure
to read the superblock ('analyse_superblocks'). Neither of these checks are
sufficient. The first check is done properly but with insufficient
information about the possible failure state of the devices to make a good
determination if the array can be activated. The second check is simply
done wrong in the case of RAID10 because it doesn't account for the
independence of the stripes (i.e. mirror sets). The solution is to use the
properly written check ('validate_rebuild_devices'), but perform the check
after the superblocks have been read and we know which devices have failed.
This gives us one check instead of two and performs it in a location where
it can be done right.
Only RAID10 was affected and it was affected in the following ways:
- the code did not properly catch the condition where a user specified
a device for rebuild that already had a failed device in the same mirror
set. (This condition would, however, be caught at a deeper level in MD.)
- the code triggers a false positive and denies activation when devices in
independent mirror sets have failed - counting the failures as though they
were all in the same set.
The most likely place this error was introduced (or this patch should have
been included) is in commit 4ec1e369 - first introduced in v3.7-rc1.
Consequently this fix should also go in v3.7.y, however there is a
small conflict on the .version in raid_target, so I'll submit a
separate patch to -stable.
Cc: stable@vger.kernel.org
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
bio completion didn't kick block_bio_complete TP. Only dm was
explicitly triggering the TP on IO completion. This makes
block_bio_complete TP useless for tracers which want to know about
bios, and all other bio based drivers skip generating blktrace
completion events.
This patch makes all bio completions via bio_endio() generate
block_bio_complete TP.
* Explicit trace_block_bio_complete() invocation removed from dm and
the trace point is unexported.
* @rq dropped from trace_block_bio_complete(). bios may fly around
w/o queue associated. Verifying and accessing the assocaited queue
belongs to TP probes.
* blktrace now gets both request and bio completions. Make it ignore
bio completions if request completion path is happening.
This makes all bio based drivers generate blktrace completion events
properly and makes the block_bio_complete TP actually useful.
v2: With this change, block_bio_complete TP could be invoked on sg
commands which have bio's with %NULL bi_bdev. Update TP
assignment code to check whether bio->bi_bdev is %NULL before
dereferencing.
Signed-off-by: Tejun Heo <tj@kernel.org>
Original-patch-by: Namhyung Kim <namhyung@gmail.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Of particular note:
- Disable broken WRITE SAME support in all targets except linear and striped.
Use it when kcopyd is zeroing blocks.
- Remove several mempools from targets by moving the data into the bio's new
front_pad area(which dm calls 'per_bio_data').
- Fix a race in thin provisioning if discards are misused.
- Prevent userspace from interfering with the ioctl parameters and
use kmalloc for the data buffer if it's small instead of vmalloc.
- Throttle some annoying error messages when I/O fails.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=yzhS
-----END PGP SIGNATURE-----
Merge tag 'dm-3.8-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull dm update from Alasdair G Kergon:
"Miscellaneous device-mapper fixes, cleanups and performance
improvements.
Of particular note:
- Disable broken WRITE SAME support in all targets except linear and
striped. Use it when kcopyd is zeroing blocks.
- Remove several mempools from targets by moving the data into the
bio's new front_pad area(which dm calls 'per_bio_data').
- Fix a race in thin provisioning if discards are misused.
- Prevent userspace from interfering with the ioctl parameters and
use kmalloc for the data buffer if it's small instead of vmalloc.
- Throttle some annoying error messages when I/O fails."
* tag 'dm-3.8-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm: (36 commits)
dm stripe: add WRITE SAME support
dm: remove map_info
dm snapshot: do not use map_context
dm thin: dont use map_context
dm raid1: dont use map_context
dm flakey: dont use map_context
dm raid1: rename read_record to bio_record
dm: move target request nr to dm_target_io
dm snapshot: use per_bio_data
dm verity: use per_bio_data
dm raid1: use per_bio_data
dm: introduce per_bio_data
dm kcopyd: add WRITE SAME support to dm_kcopyd_zero
dm linear: add WRITE SAME support
dm: add WRITE SAME support
dm: prepare to support WRITE SAME
dm ioctl: use kmalloc if possible
dm ioctl: remove PF_MEMALLOC
dm persistent data: improve improve space map block alloc failure message
dm thin: use DMERR_LIMIT for errors
...
Rename stripe_map_discard to stripe_map_range and reuse it for WRITE
SAME bio processing.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes map_info from bio-based device mapper targets.
map_info is still used for request-based targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Eliminate struct map_info from dm-snap.
map_info->ptr was used in dm-snap to indicate if the bio was tracked.
If map_info->ptr was non-NULL, the bio was linked in tracked_chunk_hash.
This patch removes the use of map_info->ptr. We determine if the bio was
tracked based on hlist_unhashed(&c->node). If hlist_unhashed is true,
the bio is not tracked, if it is false, the bio is tracked.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch removes endio_hook_pool from dm-thin and uses per-bio data instead.
This patch removes any use of map_info in preparation for the next patch
that removes map_info from bio-based device mapper.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Don't use map_info any more in dm-raid1.
map_info was used for writes to hold the region number. For this purpose
we add a new field dm_bio_details to dm_raid1_bio_record.
map_info was used for reads to hold a pointer to dm_raid1_bio_record (if
the pointer was non-NULL, bio details were saved; if the pointer was
NULL, bio details were not saved). We use
dm_raid1_bio_record.details->bi_bdev for this purpose. If bi_bdev is
NULL, details were not saved, if bi_bdev is non-NULL, details were
saved.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Replace map_info with a per-bio structure "struct per_bio_data" in dm-flakey.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename struct read_record to bio_record in dm-raid1.
In the following patch, the structure will be used for both read and
write bios, so rename it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch moves target_request_nr from map_info to dm_target_io and
makes it accessible with dm_bio_get_target_request_nr.
This patch is a preparation for the next patch that removes map_info.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Replace tracked_chunk_pool with per_bio_data in dm-snap.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Replace io_mempool with per_bio_data in dm-verity.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Replace read_record_pool with per_bio_data in dm-raid1.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce a field per_bio_data_size in struct dm_target.
Targets can set this field in the constructor. If a target sets this
field to a non-zero value, "per_bio_data_size" bytes of auxiliary data
are allocated for each bio submitted to the target. These data can be
used for any purpose by the target and help us improve performance by
removing some per-target mempools.
Per-bio data is accessed with dm_per_bio_data. The
argument data_size must be the same as the value per_bio_data_size in
dm_target.
If the target has a pointer to per_bio_data, it can get a pointer to
the bio with dm_bio_from_per_bio_data() function (data_size must be the
same as the value passed to dm_per_bio_data).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add WRITE SAME support to dm-io and make it accessible to
dm_kcopyd_zero(). dm_kcopyd_zero() provides an asynchronous interface
whereas the blkdev_issue_write_same() interface is synchronous.
WRITE SAME is a SCSI command that can be leveraged for more efficient
zeroing of a specified logical extent of a device which supports it.
Only a single zeroed logical block is transfered to the target for each
WRITE SAME and the target then writes that same block across the
specified extent.
The dm thin target uses this.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The linear target can already support WRITE SAME requests so signal
this by setting num_write_same_requests to 1.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
WRITE SAME bios have a payload that contain a single page. When
cloning WRITE SAME bios DM has no need to modify the bi_io_vec
attributes (and doing so would be detrimental). DM need only alter the
start and end of the WRITE SAME bio accordingly.
Rather than duplicate __clone_and_map_discard, factor out a common
function that is also used by __clone_and_map_write_same.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow targets to opt in to WRITE SAME support by setting
'num_write_same_requests' in the dm_target structure.
A dm device will only advertise WRITE SAME support if all its
targets and all its underlying devices support it.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If the parameter buffer is small enough, try to allocate it with kmalloc()
rather than vmalloc().
vmalloc is noticeably slower than kmalloc because it has to manipulate
page tables.
In my tests, on PA-RISC this patch speeds up activation 13 times.
On Opteron this patch speeds up activation by 5%.
This patch introduces a new function free_params() to free the
parameters and this uses new flags that record whether or not vmalloc()
was used and whether or not the input buffer must be wiped after use.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When allocating memory for the userspace ioctl data, set some
appropriate GPF flags directly instead of using PF_MEMALLOC.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Improve space map error message when unable to allocate a new
metadata block.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Throttle all errors logged from the IO path by dm thin.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Nearly all of persistent-data is in the IO path so throttle error
messages with DMERR_LIMIT to limit the amount logged when
something has gone wrong.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reinstate a useful error message when the block manager buffer validator fails.
This was mistakenly eliminated when the block manager was converted to use
dm-bufio.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If the user does not supply a bitmap region_size to the dm raid target,
a reasonable size is computed automatically. If this is not a power of 2,
the md code will report an error later.
This patch catches the problem early and rounds the region_size to the
next power of two.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove unused @data_block parameter from cell_defer.
Change thin_bio_map to use many returns rather than setting a variable.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename cell_defer_except() to cell_defer_no_holder() which describes
its function more clearly.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
track_chunk is always called with interrupts enabled. Consequently, we
do not need to save and restore interrupt state in "flags" variable.
This patch changes spin_lock_irqsave to spin_lock_irq and
spin_unlock_irqrestore to spin_unlock_irq.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use a defined macro DM_ENDIO_INCOMPLETE instead of a numeric constant.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
mempool_alloc can't fail if __GFP_WAIT is specified, so the condition
that tests if read_record is non-NULL is always true.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If "ignore_discard" is specified when creating the thin pool device then
discard support is disabled for that device. The pool device's status
should reflect this fact rather than stating "no_discard_passdown"
(which implies discards are enabled but passdown is disabled).
Reported-by: Zdenek Kabelac <zkabelac@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When deleting nested btrees, the code forgets to delete the innermost
btree. The thin-metadata code serendipitously compensates for this by
claiming there is one extra layer in the tree.
This patch corrects both problems.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When discards are prepared it is best to directly wake the worker that
will process them. The worker will be woken anyway, via periodic
commit, but there is no reason to not wake_worker here.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
There is a race when discard bios and non-discard bios are issued
simultaneously to the same block.
Discard support is expensive for all thin devices precisely because you
have to be careful to quiesce the area you're discarding. DM thin must
handle this conflicting IO pattern (simultaneous non-discard vs discard)
even though a sane application shouldn't be issuing such IO.
The race manifests as follows:
1. A non-discard bio is mapped in thin_bio_map.
This doesn't lock out parallel activity to the same block.
2. A discard bio is issued to the same block as the non-discard bio.
3. The discard bio is locked in a dm_bio_prison_cell in process_discard
to lock out parallel activity against the same block.
4. The non-discard bio's mapping continues and its all_io_entry is
incremented so the bio is accounted for in the thin pool's all_io_ds
which is a dm_deferred_set used to track time locality of non-discard IO.
5. The non-discard bio is finally locked in a dm_bio_prison_cell in
process_bio.
The race can result in deadlock, leaving the block layer hanging waiting
for completion of a discard bio that never completes, e.g.:
INFO: task ruby:15354 blocked for more than 120 seconds.
"echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
ruby D ffffffff8160f0e0 0 15354 15314 0x00000000
ffff8802fb08bc58 0000000000000082 ffff8802fb08bfd8 0000000000012900
ffff8802fb08a010 0000000000012900 0000000000012900 0000000000012900
ffff8802fb08bfd8 0000000000012900 ffff8803324b9480 ffff88032c6f14c0
Call Trace:
[<ffffffff814e5a19>] schedule+0x29/0x70
[<ffffffff814e3d85>] schedule_timeout+0x195/0x220
[<ffffffffa06b9bc1>] ? _dm_request+0x111/0x160 [dm_mod]
[<ffffffff814e589e>] wait_for_common+0x11e/0x190
[<ffffffff8107a170>] ? try_to_wake_up+0x2b0/0x2b0
[<ffffffff814e59ed>] wait_for_completion+0x1d/0x20
[<ffffffff81233289>] blkdev_issue_discard+0x219/0x260
[<ffffffff81233e79>] blkdev_ioctl+0x6e9/0x7b0
[<ffffffff8119a65c>] block_ioctl+0x3c/0x40
[<ffffffff8117539c>] do_vfs_ioctl+0x8c/0x340
[<ffffffff8119a547>] ? block_llseek+0x67/0xb0
[<ffffffff811756f1>] sys_ioctl+0xa1/0xb0
[<ffffffff810561f6>] ? sys_rt_sigprocmask+0x86/0xd0
[<ffffffff814ef099>] system_call_fastpath+0x16/0x1b
The thinp-test-suite's test_discard_random_sectors reliably hits this
deadlock on fast SSD storage.
The fix for this race is that the all_io_entry for a bio must be
incremented whilst the dm_bio_prison_cell is held for the bio's
associated virtual and physical blocks. That cell locking wasn't
occurring early enough in thin_bio_map. This patch fixes this.
Care is taken to always call the new function inc_all_io_entry() with
the relevant cells locked, but they are generally unlocked before
calling issue() to try to avoid holding the cells locked across
generic_submit_request.
Also, now that thin_bio_map may lock bios in a cell, process_bio() is no
longer the only thread that will do so. Because of this we must be sure
to use cell_defer_except() to release all non-holder entries, that
were added by the other thread, because they must be deferred.
This patch depends on "dm thin: replace dm_cell_release_singleton with
cell_defer_except".
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cc: stable@vger.kernel.org
Kent Overstreet