sienna cichlid interfaces with RAS eeprom on I2C controller port 1
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: John Clements <john.clements@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to improve the fine grain tuning function for RV/RV2/PCO.
This patch adds two new commands: "restore" and "commit".
This function uses the pp_od_clk_voltage sysfs file to configure the min
and max value of gfx clock frequency manually or restore the default value.
Command guide:
echo "s level value" > pp_od_clk_voltage
"s" - set the sclk frequency
"level" - 0 or 1, "0" represents the min value, "1" represents
the max value
"value" - the target value of sclk frequency, it should be limited in the
safe range
echo "r" > pp_od_clk_voltage
"r" - reset the sclk frequency, restore the default value instantly
echo "c" > pp_od_clk_voltage
"c" - commit the min and max value of sclk frequency to the system
only after the commit command, the target values set by "s" command
will take effect.
Example:
1)change power profile from "auto" to "manual"
$ cat power_dpm_force_performance_level
auto
$ echo "manual" > power_dpm_force_performance_level
$ cat power_dpm_force_performance_level
manual
2)check the default sclk frequency
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
3)use "s" -- set command to configure the min and max sclk frequency
$ echo "s 0 600" > pp_od_clk_voltage
$ echo "s 1 1000" > pp_od_clk_voltage
$ echo "c" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 600Mhz
1: 1000Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
4)use "r" -- reset command to restore the min or max sclk frequency
$ echo "r" > pp_od_clk_voltage
$ cat pp_od_clk_voltage
OD_SCLK:
0: 200Mhz
1: 1400Mhz
OD_RANGE:
SCLK: 200MHz 1400MHz
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This patch is to correct the sensor value of power for vangogh.
Signed-off-by: Xiaojian Du <Xiaojian.Du@amd.com>
Reviewed-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
BXT/APL has different isr/irr/hpd regs compared with other GEN9. If not
setting these regs bits correctly according to the emulated monitor
(currently a DP on PORT_B), although gvt still triggers a virtual HPD
event, the guest driver won't detect a valid HPD pulse thus no full
display detection will be executed to read the updated EDID.
With this patch, the vfio_edid is enabled again on BXT/APL, which is
previously disabled.
Fixes: 642403e359 ("drm/i915/gvt: Temporarily disable vfio_edid for BXT/APL")
Signed-off-by: Colin Xu <colin.xu@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20201201060329.142375-1-colin.xu@intel.com
Reviewed-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Since multiple connectors may run intel_dp_aux_xfer conncurrently, a
single global pm_qos does not suffice. (One connector may disable the
dma-latency boost prematurely while the second is still depending on
it.) Instead of a single global pm_qos, track the pm_qos request for
each intel_dp.
v2: Move the pm_qos setup/teardown to intel_dp_aux_init/fini
Fixes: 9ee32fea5f ("drm/i915: irq-drive the dp aux communication")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Imre Deak <imre.deak@intel.com>
Reviewed-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201230202309.23982-1-chris@chris-wilson.co.uk
(cherry picked from commit b3304591f1)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When splitting the Coffeelake define to also identify Cometlakes, I
missed the double fw_def for Coffeelake. That is only newer Cometlakes
use the cml specific guc firmware, older Cometlakes should use kbl
firmware.
Closes: https://gitlab.freedesktop.org/drm/intel/-/issues/2859
Fixes: 5f4ae2704d ("drm/i915: Identify Cometlake platform")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: <stable@vger.kernel.org> # v5.9+
Reviewed-by: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201229120828.29931-1-chris@chris-wilson.co.uk
(cherry picked from commit 70960ab275)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The reloc batch is short lived but can exist in the user visible ppGTT,
and since it's backed by an internal object, which lacks page clearing,
we should take care to clear it upfront.
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224151358.401345-2-matthew.auld@intel.com
Cc: stable@vger.kernel.org
(cherry picked from commit 26ebc511e7)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
The shadow batch is an internal object, which doesn't have any page
clearing, and since the batch_len can be smaller than the object, we
should take care to clear it.
Testcase: igt/gen9_exec_parse/shadow-peek
Fixes: 4f7af1948a ("drm/i915: Support ro ppgtt mapped cmdparser shadow buffers")
Signed-off-by: Matthew Auld <matthew.auld@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20201224151358.401345-1-matthew.auld@intel.com
Cc: stable@vger.kernel.org
(cherry picked from commit eeb52ee6c4)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
get_pages is only called in a locked context. Add a WARN_ON to make sure
it stays that way.
Signed-off-by: Iskren Chernev <iskren.chernev@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>
clang (quite rightly) complains fairly loudly about the newly added
mpc1_get_mpc_out_mux() function returning an uninitialized value if the
'opp_id' checks don't pass.
This may not happen in practice, but the code really shouldn't return
garbage if the sanity checks don't pass.
So just initialize 'val' to zero to avoid the issue.
Fixes: 110b055b28 ("drm/amd/display: add getter routine to retrieve mpcc mux")
Cc: Josip Pavic <Josip.Pavic@amd.com>
Cc: Bindu Ramamurthy <bindu.r@amd.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
accesses, inefficient and disfunctional code. The goal is to remove the
export of irq_to_desc() to prevent these things from creeping up again.
-----BEGIN PGP SIGNATURE-----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=BXv+
-----END PGP SIGNATURE-----
Merge tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq updates from Thomas Gleixner:
"This is the second attempt after the first one failed miserably and
got zapped to unblock the rest of the interrupt related patches.
A treewide cleanup of interrupt descriptor (ab)use with all sorts of
racy accesses, inefficient and disfunctional code. The goal is to
remove the export of irq_to_desc() to prevent these things from
creeping up again"
* tag 'irq-core-2020-12-23' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (30 commits)
genirq: Restrict export of irq_to_desc()
xen/events: Implement irq distribution
xen/events: Reduce irq_info:: Spurious_cnt storage size
xen/events: Only force affinity mask for percpu interrupts
xen/events: Use immediate affinity setting
xen/events: Remove disfunct affinity spreading
xen/events: Remove unused bind_evtchn_to_irq_lateeoi()
net/mlx5: Use effective interrupt affinity
net/mlx5: Replace irq_to_desc() abuse
net/mlx4: Use effective interrupt affinity
net/mlx4: Replace irq_to_desc() abuse
PCI: mobiveil: Use irq_data_get_irq_chip_data()
PCI: xilinx-nwl: Use irq_data_get_irq_chip_data()
NTB/msi: Use irq_has_action()
mfd: ab8500-debugfs: Remove the racy fiddling with irq_desc
pinctrl: nomadik: Use irq_has_action()
drm/i915/pmu: Replace open coded kstat_irqs() copy
drm/i915/lpe_audio: Remove pointless irq_to_desc() usage
s390/irq: Use irq_desc_kstat_cpu() in show_msi_interrupt()
parisc/irq: Use irq_desc_kstat_cpu() in show_interrupts()
...
* dma-buf: Include <linux/vmalloc.h> for building on MIPS
* komeda: Fix order of operation in commit tail; Fix NULL-pointer and
out-of-bounds access; Cleanups
* ttm: Fix an unused-function warning
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEchf7rIzpz2NEoWjlaA3BHVMLeiMFAl/iRSAACgkQaA3BHVML
eiMrsQf/dlHwJykbsGbkE/lG8qgrnz4jFKkei+DnZjqNaAwvgbz9s1YvaMYIIdsE
wvYnBSTvdvhYzde08+E0Q4JLCvHh/0aHWqkZR3dGd22tAgNxGfslBITu07EyI+k8
Agy4AeBbYJUwYcfRAHqwDuKCDQ28/FXcBpLajSF9K9oG6et2GgftshuIwWij2xNR
kNQTddCsXdXXbFDK/N3X/Inb+WSbRU0GWDTMTUPC31rMXX6kIKASQmVvCQ8h6a5F
N9EqjUmGf7XGjdqWEkSM34HpCUv5c5N2MWc4OAiSaP3Q3QVJyp3RHg8zLOpeSIsy
hVAj+8SN8UrI+Fz0Tx+SFdU72t0eVA==
=hlDA
-----END PGP SIGNATURE-----
Merge tag 'drm-misc-next-fixes-2020-12-22' of git://anongit.freedesktop.org/drm/drm-misc into drm-next
Short summary of fixes pull:
* dma-buf: Include <linux/vmalloc.h> for building on MIPS
* komeda: Fix order of operation in commit tail; Fix NULL-pointer and
out-of-bounds access; Cleanups
* ttm: Fix an unused-function warning
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/X+JFYlW1SEZa6ShA@linux-uq9g
EDID parsing in S3 resume pushes new display modes
to probed_modes list but doesn't consolidate to actual
mode list. This creates a race condition when
amdgpu_dm_connector_ddc_get_modes() re-initializes the
list head without walking the list and results in memory leak.
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=209987
Acked-by: Harry Wentland <harry.wentland@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Stylon Wang <stylon.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Fixes a crash in drm_object_property_set_value() because the property
is not set for internal DP ports that connect to a bridge chips
(e.g., DP to VGA or DP to LVDS).
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=210739
Fixes: 65bf2cf95d ("drm/amdgpu: utilize subconnector property for DP through atombios")
Tested-By: Kris Karas <bugs-a17@moonlit-rail.com>
Cc: Oleg Vasilev <oleg.vasilev@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.10.x
This can suppress the annoying but unharmful prompts.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why & How]
Add function to identify which MPCC is providing input to a specified OPP
Signed-off-by: Josip Pavic <Josip.Pavic@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We defer clock updates to after pipes have been programmed. In
some instances we use DPPCLK that have been previously set to be
"unused". This results in a brief window of time where underflow
could occur.
[How]
During prepare bandwidth allow rn_update_clocks_update_dpp_dto
to check each instance and compare previous clock to new clock.
If new clock is higher than previous clock, program DPPDTO.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- restore lvtma_pwrseq_delay2 from vbios integrated info table
- restore MVID/NVID after power up.
- Enable timer wake up mask when enable timer interrupt.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit latency
being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
DSC should only be acquired per OPP. Therefore, DSC should only
be acquired for the top_pipe when ODM is enabled.
Not doing this check may lead to acquiring more DSC's than needed
when doing MPO + ODM Combine.
[HOW]
Only acquire DSC if pipe is top_pipe.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FP2 programming not happening when topology changes occur with multiple
displays.
[How]
Ensure FP2 is programmed whenever global sync changes occur but wait for
VACTIVE first to avoid underflow.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
new_crtc_state is already dereferenced earlier in the function
[How]
Remove the check
Signed-off-by: Eryk Brol <eryk.brol@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
Virtual signals were previously counted as a workaround to S0i2 hang
which is fixed on Renoir. This blocks S0i3 diags testing.
[HOW]
Stop counting virtual signals as S0i2 hang is fixed on Renoir.
Signed-off-by: Michael Strauss <michael.strauss@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
there is some garbage showing up during reboot test.
Reason:
SMU might handle display driver msg defered and driver will send
next msg to SMU after 10ms timeout, once SMU FW handle previous msg,
parameters are changed to next one, which result in a wrong value be programmed.
[How]
Extend timeout to 2s so SMU will have enough time to handle driver msg.
Signed-off-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Need driver to pass values of backlight ramp start and ramp reduction so
that intensity can be ramped down appropriately.
[How]
Using abm_parameters structure to get these values from driver.
Signed-off-by: Rizvi <syerizvi@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
The sink count change HPD_IRQ will be ignored if the branch device has only
DP DFP.
[how]
To remove the port type restriction.
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
Some MST display may not report the internal panel to DEVICE_COUNT,
that makes the check condition always failed.
[how]
To update this condition with the reported device count + 1
(because the immediate repeater's internal panel is possibly
not included in DEVICE_COUNT)
Signed-off-by: Martin Tsai <martin.tsai@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[WHY]
HUBP blanking sequence on DCN30 requires us to check if HUBP is in blank
and also toggle HUBP_DISABLE, which should instead be called
HUBP_SOFT_RESET for what it does in HW.
Signed-off-by: Wesley Chalmers <Wesley.Chalmers@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[why]
handler is supposedly passed in as a function pointer;
however, the entire struct amdgpu_dm_irq_handler_data
gets from the list is used to check match.
[how]
use the interrupt_handler within amdgpu_dm_irq_handler_data
for checking match.
Signed-off-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Acked-by: Bindu Ramamurthy <bindu.r@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GUI_IDLE interrupts controlled by CP_INT_CNTL_RING0
are only applicable to me0 pipe0.
For ASICs that have gfx pipe removed, don't toggle
those bits.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The number of crtc should be 0 for ASICs that don't
have display engine. Remove the unnecessary asic type
check then.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check number of gfx ring, rather than asic type,
before cp gfx engine initialization so driver just
need to make sure number of gfx ring is initialized
correctly in gfx early_init phase. No need to add
additional asic type check everywhere when there is
new asic with gfx pipe removed.
Signed-off-by: Hawking Zhang <Hawking.Zhang@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Acked-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Only enable char/agp uapi when CONFIG_DRM_LEGACY is set
Cross-subsystem Changes:
- vma_set_file helper to make vma->vm_file changing less brittle,
acked by Andrew
Core Changes:
- dma-buf heaps improvements
- pass full atomic modeset state to driver callbacks
- shmem helpers: cached bo by default
- cleanups for fbdev, fb-helpers
- better docs for drm modes and SCALING_FITLER uapi
- ttm: fix dma32 page pool regression
Driver Changes:
- multi-hop regression fixes for amdgpu, radeon, nouveau
- lots of small amdgpu hw enabling fixes (display, pm, ...)
- fixes for imx, mcde, meson, some panels, virtio, qxl, i915, all
fairly minor
- some cleanups for legacy drm/fbdev drivers
-----BEGIN PGP SIGNATURE-----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=BhU/
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-18' of git://anongit.freedesktop.org/drm/drm
Pull more drm updates from Daniel Vetter:
"UAPI Changes:
- Only enable char/agp uapi when CONFIG_DRM_LEGACY is set
Cross-subsystem Changes:
- vma_set_file helper to make vma->vm_file changing less brittle,
acked by Andrew
Core Changes:
- dma-buf heaps improvements
- pass full atomic modeset state to driver callbacks
- shmem helpers: cached bo by default
- cleanups for fbdev, fb-helpers
- better docs for drm modes and SCALING_FITLER uapi
- ttm: fix dma32 page pool regression
Driver Changes:
- multi-hop regression fixes for amdgpu, radeon, nouveau
- lots of small amdgpu hw enabling fixes (display, pm, ...)
- fixes for imx, mcde, meson, some panels, virtio, qxl, i915, all
fairly minor
- some cleanups for legacy drm/fbdev drivers"
* tag 'drm-next-2020-12-18' of git://anongit.freedesktop.org/drm/drm: (117 commits)
drm/qxl: don't allocate a dma_address array
drm/nouveau: fix multihop when move doesn't work.
drm/i915/tgl: Fix REVID macros for TGL to fetch correct stepping
drm/i915: Fix mismatch between misplaced vma check and vma insert
drm/i915/perf: also include Gen11 in OATAILPTR workaround
Revert "drm/i915: re-order if/else ladder for hpd_irq_setup"
drm/amdgpu/disply: fix documentation warnings in display manager
drm/amdgpu: print mmhub client name for dimgrey_cavefish
drm/amdgpu: set mode1 reset as default for dimgrey_cavefish
drm/amd/display: Add get_dig_frontend implementation for DCEx
drm/radeon: remove h from printk format specifier
drm/amdgpu: remove h from printk format specifier
drm/amdgpu: Fix spelling mistake "Heterogenous" -> "Heterogeneous"
drm/amdgpu: fix regression in vbios reservation handling on headless
drm/amdgpu/SRIOV: Extend VF reset request wait period
drm/amdkfd: correct amdgpu_amdkfd_gpuvm_alloc_memory_of_gpu log.
drm/amd/display: Adding prototype for dccg21_update_dpp_dto()
drm/amdgpu: print what method we are using for runtime pm
drm/amdgpu: simplify logic in atpx resume handling
drm/amdgpu: no need to call pci_ignore_hotplug for _PR3
...
KASAN found this problem. find_first_bit() expects to look at a
pointer pointing to a long, but we look at a u32 - this is going to be
an issue with endianness but, KSAN already flags this as out-of-bounds
stack reads. This fixes it by just importing inot a local long.
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218150812.68195-1-carsten.haitzler@foss.arm.com
komeda_component_get_old_state() technically can return a NULL
pointer. komeda_compiz_set_input() even warns when this happens, but
then proceeeds to use that NULL pointer to compare memory content there
agains the new state to see if it changed. In this case, it's better to
assume that the input changed as there is no old state to compare
against and thus assume the changes happen anyway.
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
[Applied small spelling fixes and fix suggested by Steven Price]
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127110054.133686-1-carsten.haitzler@foss.arm.com
ret is not actually read after this (only written in one case then
returned), so this assign line is useless. This removes that assignment.
Signed-off-by: Carsten Haitzler <carsten.haitzler@arm.com>
Reviewed-by: Steven Price <steven.price@arm.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127110027.133569-1-carsten.haitzler@foss.arm.com
Komeda HW has no special, program the update to HW is done first,
then flip happens. So correct the sequence to hw_done() first then
flip_done().
Reported-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: James Qian Wang <james.qian.wang@arm.com>
Acked-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201119013948.2866343-1-james.qian.wang@arm.com
That seems to be unused.
Daniel: Mike reported a warning when booting with qxl, which this
patch fixes:
[ 1.815561] WARNING: CPU: 7 PID: 355 at drivers/gpu/drm/ttm/ttm_pool.c:365 ttm_pool_alloc+0x41b/0x540 [ttm]
Signed-off-by: Christian König <christian.koenig@amd.com>
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Mike Galbraith <efault@gmx.de>
References: https://lore.kernel.org/lkml/7cb43d5b-4e6a-defc-1ab6-5f713ad5a963@amd.com/
Reviewed-by: David Airlie <airlied@redhat.com>
[davnet: bring commit message up to par.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201218134243.110884-1-christian.koenig@amd.com
As per the radeon/amdgpu fix don't use multihop if hw moves
aren't enabled.
Reported-by: Mike Galbraith <efault@gmx.de>
Tested-by: Mike Galbraith <efault@gmx.de>
Fixes: 0c8c0659d7 ("drm/nouveau/ttm: use multihop")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/20201217200943.30511-1-airlied@gmail.com
Fix TGL REVID macros to fetch correct display/gt stepping based
on SOC rev id from INTEL_REVID() macro. Previously, we were just
returning the first element of the revid array instead of using
the correct index based on SOC rev id.
Fixes: c33298cb34 ("drm/i915/tgl: Fix stepping WA matching")
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Aditya Swarup <aditya.swarup@intel.com>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: Lucas De Marchi <lucas.demarchi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201203072359.156682-1-aditya.swarup@intel.com
(cherry picked from commit 83dbd74f82)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
When inserting a VMA, we restrict the placement to the low 4G unless the
caller opts into using the full range. This was done to allow usersapce
the opportunity to transition slowly from a 32b address space, and to
avoid breaking inherent 32b assumptions of some commands.
However, for insert we limited ourselves to 4G-4K, but on verification
we allowed the full 4G. This causes some attempts to bind a new buffer
to sporadically fail with -ENOSPC, but at other times be bound
successfully.
commit 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1
page") suggests that there is a genuine problem with stateless addressing
that cannot utilize the last page in 4G and so we purposefully excluded
it. This means that the quick pin pass may cause us to utilize a buggy
placement.
Reported-by: CQ Tang <cq.tang@intel.com>
Testcase: igt/gem_exec_params/larger-than-life-batch
Fixes: 48ea1e32c3 ("drm/i915/gen9: Set PIN_ZONE_4G end to 4GB - 1 page")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: CQ Tang <cq.tang@intel.com>
Reviewed-by: CQ Tang <cq.tang@intel.com>
Reviewed-by: Matthew Auld <matthew.auld@intel.com>
Cc: <stable@vger.kernel.org> # v4.5+
Link: https://patchwork.freedesktop.org/patch/msgid/20201216092951.7124-1-chris@chris-wilson.co.uk
(cherry picked from commit 5f22cc0b13)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
We now use ilk_hpd_irq_setup for all GMCH platforms that do not have
hotplug. These are early gen3 and gen2 devices that now explode on boot
as they try to access non-existent registers.
Fixes: 794d61a190 ("drm/i915: re-order if/else ladder for hpd_irq_setup")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: José Roberto de Souza <jose.souza@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201127145748.29491-1-chris@chris-wilson.co.uk
(cherry picked from commit e5346a1ff3)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
There is no reserveration so set the size to 0. Fixes
a regression on SR-IOV.
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Only pmfw version behind v4.63.23.00 could support this message.
Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
GFX10 CP firmware expects PCIe atomics support. Don't enumerate GFX10
devices on platforms (PCIe v2) that don't support PCIe atomics.
Currently, some of the applications like clinfo soft hangs on platforms
without PCIe atomics support.
Signed-off-by: Harish Kasiviswanathan <Harish.Kasiviswanathan@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Commit 991fcb77f4 ("drm/edid: Fix uninitialized variable in
drm_cvt_modes()") just replaced one warning with another.
The original warning about a possibly uninitialized variable was due to
the compiler not being smart enough to see that the case statement
actually enumerated all possible cases. And the initial fix was just to
add a "default" case that had a single "unreachable()", just to tell the
compiler that that situation cannot happen.
However, that doesn't actually fix the fundamental reason for the
problem: the compiler still doesn't see that the existing case
statements enumerate all possibilities, so the compiler will still
generate code to jump to that unreachable case statement. It just won't
complain about an uninitialized variable any more.
So now the compiler generates code to our inline asm marker that we told
it would not fall through, and end end result is basically random. We
have created a bridge to nowhere.
And then, depending on the random details of just exactly what the
compiler ends up doing, 'objtool' might end up complaining about the
conditional branches (for conditions that cannot happen, and that thus
will never be taken - but if the compiler was not smart enough to figure
that out, we can't expect objtool to do so) going off in the weeds.
So depending on how the compiler has laid out the result, you might see
something like this:
drivers/gpu/drm/drm_edid.o: warning: objtool: do_cvt_mode() falls through to next function drm_mode_detailed.isra.0()
and now you have a truly inscrutable warning that makes no sense at all
unless you start looking at whatever random code the compiler happened
to generate for our bare "unreachable()" statement.
IOW, don't use "unreachable()" unless you have an _active_ operation
that generates code that actually makes it obvious that something is not
reachable (ie an UD instruction or similar).
Solve the "compiler isn't smart enough" problem by just marking one of
the cases as "default", so that even when the compiler doesn't otherwise
see that we've enumerated all cases, the compiler will feel happy and
safe about there always being a valid case that initializes the 'width'
variable.
This also generates better code, since now the compiler doesn't generate
comparisons for five different possibilities (the four real ones and the
one that can't happen), but just for the three real ones and "the rest"
(which is that last one).
A smart enough compiler that sees that we cover all the cases won't care.
Cc: Lyude Paul <lyude@redhat.com>
Cc: Ilia Mirkin <imirkin@alum.mit.edu>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There are a couple of subsystems maintained by other people that
merge their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control
and SoC identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660
and SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs.
There is a trivial conflict in the cedrus driver, with two branches
adding the same CEDRUS_CAPABILITY_H265_DEC flag, and another trivial
remove/remove conflict in linux/dma-mapping.h.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----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=BjJf
-----END PGP SIGNATURE-----
Merge tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC driver updates from Arnd Bergmann:
"There are a couple of subsystems maintained by other people that merge
their drivers through the SoC tree, those changes include:
- The SCMI firmware framework gains support for sensor notifications
and for controlling voltage domains.
- A large update for the Tegra memory controller driver, integrating
it better with the interconnect framework
- The memory controller subsystem gains support for Mediatek MT8192
- The reset controller framework gains support for sharing pulsed
resets
For Soc specific drivers in drivers/soc, the main changes are
- The Allwinner/sunxi MBUS gets a rework for the way it handles
dma_map_ops and offsets between physical and dma address spaces.
- An errata fix plus some cleanups for Freescale Layerscape SoCs
- A cleanup for renesas drivers regarding MMIO accesses.
- New SoC specific drivers for Mediatek MT8192 and MT8183 power
domains
- New SoC specific drivers for Aspeed AST2600 LPC bus control and SoC
identification.
- Core Power Domain support for Qualcomm MSM8916, MSM8939, SDM660 and
SDX55.
- A rework of the TI AM33xx 'genpd' power domain support to use
information from DT instead of platform data
- Support for TI AM64x SoCs
- Allow building some Amlogic drivers as modules instead of built-in
Finally, there are numerous cleanups and smaller bug fixes for
Mediatek, Tegra, Samsung, Qualcomm, TI OMAP, Amlogic, Rockchips,
Renesas, and Xilinx SoCs"
* tag 'arm-soc-drivers-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (222 commits)
soc: mediatek: mmsys: Specify HAS_IOMEM dependency for MTK_MMSYS
firmware: xilinx: Properly align function parameter
firmware: xilinx: Add a blank line after function declaration
firmware: xilinx: Remove additional newline
firmware: xilinx: Fix kernel-doc warnings
firmware: xlnx-zynqmp: fix compilation warning
soc: xilinx: vcu: add missing register NUM_CORE
soc: xilinx: vcu: use vcu-settings syscon registers
dt-bindings: soc: xlnx: extract xlnx, vcu-settings to separate binding
soc: xilinx: vcu: drop useless success message
clk: samsung: mark PM functions as __maybe_unused
soc: samsung: exynos-chipid: initialize later - with arch_initcall
soc: samsung: exynos-chipid: order list of SoCs by name
memory: jz4780_nemc: Fix potential NULL dereference in jz4780_nemc_probe()
memory: ti-emif-sram: only build for ARMv7
memory: tegra30: Support interconnect framework
memory: tegra20: Support hardware versioning and clean up OPP table initialization
dt-bindings: memory: tegra20-emc: Document opp-supported-hw property
soc: rockchip: io-domain: Fix error return code in rockchip_iodomain_probe()
reset-controller: ti: force the write operation when assert or deassert
...
- IOVA allocation optimisations and removal of unused code
- Introduction of DOMAIN_ATTR_IO_PGTABLE_CFG for parameterising the
page-table of an IOMMU domain
- Support for changing the default domain type in sysfs
- Optimisation to the way in which identity-mapped regions are created
- Driver updates:
* Arm SMMU updates, including continued work on Shared Virtual Memory
* Tegra SMMU updates, including support for PCI devices
* Intel VT-D updates, including conversion to the IOMMU-DMA API
- Cleanup, kerneldoc and minor refactoring
-----BEGIN PGP SIGNATURE-----
iQFEBAABCgAuFiEEPxTL6PPUbjXGY88ct6xw3ITBYzQFAl/XWy8QHHdpbGxAa2Vy
bmVsLm9yZwAKCRC3rHDchMFjNPejB/46QsXATkWt7hbDPIxlUvzUG8VP/FBNJ6A3
/4Z+4KBXR3zhvZJOEqTarnm6Uc22tWkYpNS3QAOuRW0EfVeD8H+og4SOA2iri5tR
x3GZUCng93APWpHdDtJP7kP/xuU47JsBblY/Ip9aJKYoXi9c9svtssAqKr008wxr
knv/xv/awQ0O7CNc3gAoz7mUagQxG/no+HMXMT3Fz9KWRzzvTi6s+7ZDm2faI0hO
GEJygsKbXxe1qbfeGqKTP/67EJVqjTGsLCF2zMogbnnD7DxadJ2hP0oNg5tvldT/
oDj9YWG6oLMfIVCwDVQXuWNfKxd7RGORMbYwKNAaRSvmkli6625h
=KFOO
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull IOMMU updates from Will Deacon:
"There's a good mixture of improvements to the core code and driver
changes across the board.
One thing worth pointing out is that this includes a quirk to work
around behaviour in the i915 driver (see 65f746e828 ("iommu: Add
quirk for Intel graphic devices in map_sg")), which otherwise
interacts badly with the conversion of the intel IOMMU driver over to
the DMA-IOMMU APU but has being fixed properly in the DRM tree.
We'll revert the quirk later this cycle once we've confirmed that
things don't fall apart without it.
Summary:
- IOVA allocation optimisations and removal of unused code
- Introduction of DOMAIN_ATTR_IO_PGTABLE_CFG for parameterising the
page-table of an IOMMU domain
- Support for changing the default domain type in sysfs
- Optimisation to the way in which identity-mapped regions are
created
- Driver updates:
* Arm SMMU updates, including continued work on Shared Virtual
Memory
* Tegra SMMU updates, including support for PCI devices
* Intel VT-D updates, including conversion to the IOMMU-DMA API
- Cleanup, kerneldoc and minor refactoring"
* tag 'iommu-updates-v5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux: (50 commits)
iommu/amd: Add sanity check for interrupt remapping table length macros
dma-iommu: remove __iommu_dma_mmap
iommu/io-pgtable: Remove tlb_flush_leaf
iommu: Stop exporting free_iova_mem()
iommu: Stop exporting alloc_iova_mem()
iommu: Delete split_and_remove_iova()
iommu/io-pgtable-arm: Remove unused 'level' parameter from iopte_type() macro
iommu: Defer the early return in arm_(v7s/lpae)_map
iommu: Improve the performance for direct_mapping
iommu: avoid taking iova_rbtree_lock twice
iommu/vt-d: Avoid GFP_ATOMIC where it is not needed
iommu/vt-d: Remove set but not used variable
iommu: return error code when it can't get group
iommu: Fix htmldocs warnings in sysfs-kernel-iommu_groups
iommu: arm-smmu-impl: Add a space before open parenthesis
iommu: arm-smmu-impl: Use table to list QCOM implementations
iommu/arm-smmu: Move non-strict mode to use io_pgtable_domain_attr
iommu/arm-smmu: Add support for pagetable config domain attribute
iommu: Document usage of "/sys/kernel/iommu_groups/<grp_id>/type" file
iommu: Take lock before reading iommu group default domain type
...
Add documentation for crc window.
Fixes: c920888c60 ("drm/amd/display: Expose new CRC window property")
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: Wayne Lin <Wayne.Lin@amd.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Wayne Lin <Wayne.Lin@amd.com>
This makes it easier to debug what block is causing the fault, same as
sienna_cichlid.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Jiansong Chen <Jiansong.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Use mode1 reset for dimgrey_cavefish by default.
Signed-off-by: Tao Zhou <tao.zhou1@amd.com>
Reviewed-by: Jiansong Chen <Jiansong.Chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Some old ASICs might not implement/require get_dig_frontend helper; in
this scenario, we can have a NULL pointer exception when we try to call
it inside vbios disable operation. For example, this situation might
happen when using Polaris12 with an eDP panel. This commit avoids this
situation by adding a specific get_dig_frontend implementation for DCEx.
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Harry Wentland <Harry.Wentland@amd.com>
Cc: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Cc: Chiawen Huang <chiawen.huang@amd.com>
Reported-and-tested-by: Borislav Petkov <bp@suse.de>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
ttm_pool_type_count() is not used when debugfs is disabled:
drivers/gpu/drm/ttm/ttm_pool.c:243:21: error: unused function 'ttm_pool_type_count' [-Werror,-Wunused-function]
static unsigned int ttm_pool_type_count(struct ttm_pool_type *pt)
Move the definition into the #ifdef block.
Fixes: d099fc8f54 ("drm/ttm: new TT backend allocation pool v3")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Martin Peres <martin.peres@mupuf.org>
Reviewed-by: Christian König <christian.koenig@amd.com>
Link: https://patchwork.freedesktop.org/patch/405695/
Signed-off-by: Christian König <christian.koenig@amd.com>
Now that relay_open() accepts const callbacks, make relay callbacks const.
Link: https://lkml.kernel.org/r/534d089f413db98aa0b94773fa49d5275d0d3c25.1606153547.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Kalle Valo <kvalo@codeaurora.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----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=xRTv
-----END PGP SIGNATURE-----
Merge tag 'pci-v5.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Decode PCIe 64 GT/s link speed (Gustavo Pimentel)
- Remove unused HAVE_PCI_SET_MWI (Heiner Kallweit)
- Reduce pci_set_cacheline_size() message to debug level (Heiner
Kallweit)
- Fix pci_slot_release() NULL pointer dereference (Jubin Zhong)
- Unify ECAM constants in native PCI Express drivers (Krzysztof
Wilczyński)
- Return u8 from pci_find_capability() and similar (Puranjay Mohan)
- Return u16 from pci_find_ext_capability() and similar (Bjorn
Helgaas)
- Fix ACPI companion lookup for device 0 on the root bus (Rafael J.
Wysocki)
Resource management:
- Keep both device and resource name for config space remaps
(Alexander Lobakin)
- Bounds-check command-line resource alignment requests (Bjorn
Helgaas)
- Fix overflow in command-line resource alignment requests (Colin Ian
King)
Driver binding:
- Avoid duplicate IDs in driver dynamic IDs list (Zhenzhong Duan)
Power management:
- Save/restore Precision Time Measurement Capability for
suspend/resume (David E. Box)
- Disable PTM during suspend to save power (David E. Box)
- Add sysfs attribute for device power state (Maximilian Luz)
- Rename pci_wakeup_bus() to pci_resume_bus() (Mika Westerberg)
- Do not generate wakeup event when runtime resuming device (Mika
Westerberg)
- Save/restore ASPM L1SS Capability for suspend/resume (Vidya Sagar)
Virtualization:
- Mark AMD Raven iGPU ATS as broken in some platforms (Alex Deucher)
- Add function 1 DMA alias quirk for Marvell 9215 SATA controller
(Bjorn Helgaas)
MSI:
- Disable MSI for Pericom PCIe-USB adapter (Andy Shevchenko)
- Improve warnings for 32-bit-limited MSI support (Vidya Sagar)
Error handling:
- Cache RCEC EA Capability offset in pci_init_capabilities() (Sean V
Kelley)
- Rename reset_link() to reset_subordinates() (Sean V Kelley)
- Write AER Capability only when we control it (Sean V Kelley)
- Clear AER status only when we control AER (Sean V Kelley)
- Bind RCEC devices to the Root Port driver (Qiuxu Zhuo)
- Recover from RCiEP AER errors (Qiuxu Zhuo)
- Recover from RCEC AER errors (Sean V Kelley)
- Add pcie_link_rcec() to associate RCiEPs (Sean V Kelley)
- Add pcie_walk_rcec() to RCEC AER handling (Sean V Kelley)
- Add pcie_walk_rcec() to RCEC PME handling (Sean V Kelley)
- Add RCEC AER error injection support (Qiuxu Zhuo)
Broadcom iProc PCIe controller driver:
- Fix out-of-bound array accesses (Bharat Gooty)
- Invalidate correct PAXB inbound windows (Roman Bacik)
- Enhance PCIe Link information display (Srinath Mannam)
Cadence PCIe controller driver:
- Make "cdns,max-outbound-regions" property optional (Kishon Vijay
Abraham I)
Intel VMD host bridge driver:
- Offset client MSI-X vectors (Jon Derrick)
- Update type of __iomem pointers (Krzysztof Wilczyński)
NVIDIA Tegra PCIe controller driver:
- Move "dbi" accesses to post common DWC initialization (Vidya Sagar)
- Read "dbi" base address to program in application logic (Vidya
Sagar)
- Fix ASPM-L1SS advertisement disable code (Vidya Sagar)
- Set DesignWare IP version (Vidya Sagar)
- Continue unconfig sequence even if parts fail (Vidya Sagar)
- Check return value of tegra_pcie_init_controller() (Vidya Sagar)
- Disable LTSSM during L2 entry (Vidya Sagar)
Qualcomm PCIe controller driver:
- Document PCIe bindings for SM8250 SoC (Manivannan Sadhasivam)
- Add SM8250 SoC support (Manivannan Sadhasivam)
- Add support for configuring BDF to SID mapping for SM8250
(Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- rcar: Drop unused members from struct rcar_pcie_host (Lad
Prabhakar)
- PCI: rcar-pci-host: Document r8a774e1 bindings (Lad Prabhakar)
- PCI: rcar-pci-host: Convert bindings to json-schema (Yoshihiro
Shimoda)
- PCI: rcar-pci-host: Document r8a77965 bindings (Yoshihiro Shimoda)
Samsung Exynos PCIe controller driver:
- Rework driver to support Exynos5433 PCIe PHY (Jaehoon Chung)
- Rework driver to support Exynos5433 variant (Jaehoon Chung)
- Drop samsung,exynos5440-pcie binding (Marek Szyprowski)
- Add the samsung,exynos-pcie binding (Marek Szyprowski)
- Add the samsung,exynos-pcie-phy binding (Marek Szyprowski)
Synopsys DesignWare PCIe controller driver:
- Support multiple ATU memory regions (Rob Herring)
- Move intel-gw ATU offset out of driver match data (Rob Herring)
- Move "dbi", "dbi2", and "addr_space" resource setup into common
code (Rob Herring)
- Remove intel-gw unneeded function wrappers (Rob Herring)
- Ensure all outbound ATU windows are reset (Rob Herring)
- Use the common MSI irq_chip in dra7xx (Rob Herring)
- Drop the .set_num_vectors() host op (Rob Herring)
- Move MSI interrupt setup into DWC common code (Rob Herring)
- Rework MSI initialization (Rob Herring)
- Move link handling into common code (Rob Herring)
- Move dw_pcie_msi_init() into core (Rob Herring)
- Move dw_pcie_setup_rc() to DWC common code (Rob Herring)
- Remove unnecessary wrappers around dw_pcie_host_init() (Rob
Herring)
- Drop keystone duplicated 'num-viewport'" (Rob Herring)
- Move inbound and outbound windows to common struct (Rob Herring)
- Detect number of iATU windows (Rob Herring)
- Warn if non-prefetchable memory aperture size is > 32-bit (Vidya
Sagar)
- Add support to program ATU for >4GB memory (Vidya Sagar)
- Set 32-bit DMA mask for MSI target address allocation (Vidya Sagar)
TI J721E PCIe driver:
- Fix "ti,syscon-pcie-ctrl" to take argument (Kishon Vijay Abraham I)
- Add host mode dt-bindings for TI's J7200 SoC (Kishon Vijay Abraham
I)
- Add EP mode dt-bindings for TI's J7200 SoC (Kishon Vijay Abraham I)
- Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
(Kishon Vijay Abraham I)
TI Keystone PCIe controller driver:
- Enable compile-testing on !ARM (Alex Dewar)"
* tag 'pci-v5.11-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (100 commits)
PCI: Add function 1 DMA alias quirk for Marvell 9215 SATA controller
PCI/ACPI: Fix companion lookup for device 0 on the root bus
PCI: Keep both device and resource name for config space remaps
PCI: xgene: Removed unused ".bus_shift" initialisers from pci-xgene.c
PCI: vmd: Update type of the __iomem pointers
PCI: iproc: Convert to use the new ECAM constants
PCI: thunder-pem: Add constant for custom ".bus_shift" initialiser
PCI: Unify ECAM constants in native PCI Express drivers
PCI: Disable PTM during suspend to save power
PCI/PTM: Save/restore Precision Time Measurement Capability for suspend/resume
PCI: Mark AMD Raven iGPU ATS as broken in some platforms
PCI: j721e: Get offset within "syscon" from "ti,syscon-pcie-ctrl" phandle arg
dt-bindings: PCI: Add EP mode dt-bindings for TI's J7200 SoC
dt-bindings: PCI: Add host mode dt-bindings for TI's J7200 SoC
dt-bindings: pci: ti,j721e: Fix "ti,syscon-pcie-ctrl" to take argument
PCI: dwc: Set 32-bit DMA mask for MSI target address allocation
PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
PCI: Reduce pci_set_cacheline_size() message to debug level
PCI: Remove unused HAVE_PCI_SET_MWI
PCI: qcom: Add SM8250 SoC support
...
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from
the frequency table as the current frequency and clean up that
driver (Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle
driver (Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables
in DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it
to take the interconnect and OPP information from DT and clean it
up ((Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print
driver flags for devices with debug enabled (Alex Shi, Patrice
Chotard, Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan).
-----BEGIN PGP SIGNATURE-----
iQJGBAABCAAwFiEE4fcc61cGeeHD/fCwgsRv/nhiVHEFAl/Y8mcSHHJqd0Byand5
c29ja2kubmV0AAoJEILEb/54YlRxjY4QAKsNFJeEtjGCxq7MxQIML3QLAsdJM9of
9kkY9skMEw4v1TRmyy7sW9jZW2pLSRcLJwWRKWu4143qUS3YUp2DQ0lqX4WyXoWu
BhnkhkMUl6iCeBO8CWnt8zsTuqSa20A13sL9LyqN1+7OZKHD8StbT4hKjBncdNNN
4aDj+1uAPyOgj2iCUZuHQ8DtpBvOLjgTh367vbhbufjeJ//8/9+R7s4Xzrj7wtmv
JlE0LDgvge9QeGTpjhxQJzn0q2/H5fg9jbmjPXUfbHJNuyKhrqnmjGyrN5m256JI
8DqGqQtJpmFp7Ihrur3uKTk3gWO05YwJ1FdeEooAKEjEMObm5xuYhKVRoDhmlJAu
G6ui+OAUvNR0FffJtbzvWe/pLovLGOEOHdvTrZxUF8Abo6br3untTm8rKTi1fhaF
wWndSMw0apGsPzCx5T+bE7AbJz2QHFpLhaVAutenuCzNI8xoMlxNKEzsaVz/+FqL
Pq/PdFaM4vNlMbv7hkb/fujkCs/v3EcX2ihzvt7I2o8dBS0D1X8A4mnuWJmiGslw
1ftbJ6M9XacwkPBTHPgeXxJh2C1yxxe5VQ9Z5fWWi7sPOUeJnUwxKaluv+coFndQ
sO6JxsPQ4hQihg8yOxLEkL6Wn68sZlmp+u2Oj+TPFAsAGANIA8rJlBPo1ppJWvdQ
j1OCIc/qzwpH
=BVdX
-----END PGP SIGNATURE-----
Merge tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"These update cpufreq (core and drivers), cpuidle (polling state
implementation and the PSCI driver), the OPP (operating performance
points) framework, devfreq (core and drivers), the power capping RAPL
(Running Average Power Limit) driver, the Energy Model support, the
generic power domains (genpd) framework, the ACPI device power
management, the core system-wide suspend code and power management
utilities.
Specifics:
- Use local_clock() instead of jiffies in the cpufreq statistics to
improve accuracy (Viresh Kumar).
- Fix up OPP usage in the cpufreq-dt and qcom-cpufreq-nvmem cpufreq
drivers (Viresh Kumar).
- Clean up the cpufreq core, the intel_pstate driver and the
schedutil cpufreq governor (Rafael Wysocki).
- Fix up error code paths in the sti-cpufreq and mediatek cpufreq
drivers (Yangtao Li, Qinglang Miao).
- Fix cpufreq_online() to return error codes instead of success (0)
in all cases when it fails (Wang ShaoBo).
- Add mt8167 support to the mediatek cpufreq driver and blacklist
mt8516 in the cpufreq-dt-platdev driver (Fabien Parent).
- Modify the tegra194 cpufreq driver to always return values from the
frequency table as the current frequency and clean up that driver
(Sumit Gupta, Jon Hunter).
- Modify the arm_scmi cpufreq driver to allow it to discover the
power scale present in the performance protocol and provide this
information to the Energy Model (Lukasz Luba).
- Add missing MODULE_DEVICE_TABLE to several cpufreq drivers (Pali
Rohár).
- Clean up the CPPC cpufreq driver (Ionela Voinescu).
- Fix NVMEM_IMX_OCOTP dependency in the imx cpufreq driver (Arnd
Bergmann).
- Rework the poling interval selection for the polling state in
cpuidle (Mel Gorman).
- Enable suspend-to-idle for PSCI OSI mode in the PSCI cpuidle driver
(Ulf Hansson).
- Modify the OPP framework to support empty (node-less) OPP tables in
DT for passing dependency information (Nicola Mazzucato).
- Fix potential lockdep issue in the OPP core and clean up the OPP
core (Viresh Kumar).
- Modify dev_pm_opp_put_regulators() to accept a NULL argument and
update its users accordingly (Viresh Kumar).
- Add frequency changes tracepoint to devfreq (Matthias Kaehlcke).
- Add support for governor feature flags to devfreq, make devfreq
sysfs file permissions depend on the governor and clean up the
devfreq core (Chanwoo Choi).
- Clean up the tegra20 devfreq driver and deprecate it to allow
another driver based on EMC_STAT to be used instead of it (Dmitry
Osipenko).
- Add interconnect support to the tegra30 devfreq driver, allow it to
take the interconnect and OPP information from DT and clean it up
(Dmitry Osipenko).
- Add interconnect support to the exynos-bus devfreq driver along
with interconnect properties documentation (Sylwester Nawrocki).
- Add suport for AMD Fam17h and Fam19h processors to the RAPL power
capping driver (Victor Ding, Kim Phillips).
- Fix handling of overly long constraint names in the powercap
framework (Lukasz Luba).
- Fix the wakeup configuration handling for bridges in the ACPI
device power management core (Rafael Wysocki).
- Add support for using an abstract scale for power units in the
Energy Model (EM) and document it (Lukasz Luba).
- Add em_cpu_energy() micro-optimization to the EM (Pavankumar
Kondeti).
- Modify the generic power domains (genpd) framwework to support
suspend-to-idle (Ulf Hansson).
- Fix creation of debugfs nodes in genpd (Thierry Strudel).
- Clean up genpd (Lina Iyer).
- Clean up the core system-wide suspend code and make it print driver
flags for devices with debug enabled (Alex Shi, Patrice Chotard,
Chen Yu).
- Modify the ACPI system reboot code to make it prepare for system
power off to avoid confusing the platform firmware (Kai-Heng Feng).
- Update the pm-graph (multiple changes, mostly usability-related)
and cpupower (online and offline CPU information support) PM
utilities (Todd Brandt, Brahadambal Srinivasan)"
* tag 'pm-5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (86 commits)
cpufreq: Fix cpufreq_online() return value on errors
cpufreq: Fix up several kerneldoc comments
cpufreq: stats: Use local_clock() instead of jiffies
cpufreq: schedutil: Simplify sugov_update_next_freq()
cpufreq: intel_pstate: Simplify intel_cpufreq_update_pstate()
PM: domains: create debugfs nodes when adding power domains
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
PM / EM: Micro optimization in em_cpu_energy
cpufreq: arm_scmi: Discover the power scale in performance protocol
...
Pull thermal updates from Daniel Lezcano:
- Add upper and lower limits clamps for the cooling device state in the
power allocator governor (Michael Kao)
- Add upper and lower limits support for the power allocator governor
(Lukasz Luba)
- Optimize conditions testing for the trip points (Bernard Zhao)
- Replace spin_lock_irqsave by spin_lock in hard IRQ on the rcar driver
(Tian Tao)
- Add MT8516 dt-bindings and device reset optional support (Fabien
Parent)
- Add a quiescent period to cool down the PCH when entering S0iX
(Sumeet Pawnikar)
- Use bitmap API instead of re-inventing the wheel on sun8i (Yangtao
Li)
- Remove useless NULL check in the hwmon driver (Bernard Zhao)
- Update the current state in the cpufreq cooling device only if the
frequency change is effective (Zhuguangqing)
- Improve the schema validation for the rcar DT bindings (Geert
Uytterhoeven)
- Fix the user time unit in the documentation (Viresh Kumar)
- Add PCI ids for Lewisburg PCH (Andres Freund)
- Add hwmon support on amlogic (Martin Blumenstingl)
- Fix build failure for PCH entering on in S0iX (Randy Dunlap)
- Improve the k_* coefficient for the power allocator governor (Lukasz
Luba)
- Fix missing const on a sysfs attribute (Rikard Falkeborn)
- Remove broken interrupt support on rcar to be replaced by a new one
(Niklas Söderlund)
- Improve the error code handling at init time on imx8mm (Fabio
Estevam)
- Compute interval validity once instead at each temperature reading
iteration on acerhdf (Daniel Lezcano)
- Add r8a779a0 support (Niklas Söderlund)
- Add PCI ids for AlderLake PCH and mmio refactoring (Srinivas
Pandruvada)
- Add RFIM and mailbox support on int340x (Srinivas Pandruvada)
- Use macro for temperature calculation on PCH (Sumeet Pawnikar)
- Simplify return conditions at probe time on Broadcom (Zheng Yongjun)
- Fix workload name on PCH (Srinivas Pandruvada)
- Migrate the devfreq cooling device code to the energy model API
(Lukasz Luba)
- Emit a warning if the thermal_zone_device_update is called without
the .get_temp() ops (Daniel Lezcano)
- Add critical and hot ops for the thermal zone (Daniel Lezcano)
- Remove notification usage when critical is reached on rcar (Daniel
Lezcano)
- Fix devfreq build when ENERGY_MODEL is not set (Lukasz Luba)
* tag 'thermal-v5.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (45 commits)
thermal/drivers/devfreq_cooling: Fix the build when !ENERGY_MODEL
thermal/drivers/rcar: Remove notification usage
thermal/core: Add critical and hot ops
thermal/core: Emit a warning if the thermal zone is updated without ops
drm/panfrost: Register devfreq cooling and attempt to add Energy Model
thermal: devfreq_cooling: remove old power model and use EM
thermal: devfreq_cooling: add new registration functions with Energy Model
thermal: devfreq_cooling: use a copy of device status
thermal: devfreq_cooling: change tracing function and arguments
thermal: int340x: processor_thermal: Correct workload type name
thermal: broadcom: simplify the return expression of bcm2711_thermal_probe()
thermal: intel: pch: use macro for temperature calculation
thermal: int340x: processor_thermal: Add mailbox driver
thermal: int340x: processor_thermal: Add RFIM driver
thermal: int340x: processor_thermal: Add AlderLake PCI device id
thermal: int340x: processor_thermal: Refactor MMIO interface
thermal: rcar_gen3_thermal: Add r8a779a0 support
dt-bindings: thermal: rcar-gen3-thermal: Add r8a779a0 support
platform/x86/drivers/acerhdf: Check the interval value when it is set
platform/x86/drivers/acerhdf: Use module_param_cb to set/get polling interval
...
Merge misc updates from Andrew Morton:
- a few random little subsystems
- almost all of the MM patches which are staged ahead of linux-next
material. I'll trickle to post-linux-next work in as the dependents
get merged up.
Subsystems affected by this patch series: kthread, kbuild, ide, ntfs,
ocfs2, arch, and mm (slab-generic, slab, slub, dax, debug, pagecache,
gup, swap, shmem, memcg, pagemap, mremap, hmm, vmalloc, documentation,
kasan, pagealloc, memory-failure, hugetlb, vmscan, z3fold, compaction,
oom-kill, migration, cma, page-poison, userfaultfd, zswap, zsmalloc,
uaccess, zram, and cleanups).
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (200 commits)
mm: cleanup kstrto*() usage
mm: fix fall-through warnings for Clang
mm: slub: convert sysfs sprintf family to sysfs_emit/sysfs_emit_at
mm: shmem: convert shmem_enabled_show to use sysfs_emit_at
mm:backing-dev: use sysfs_emit in macro defining functions
mm: huge_memory: convert remaining use of sprintf to sysfs_emit and neatening
mm: use sysfs_emit for struct kobject * uses
mm: fix kernel-doc markups
zram: break the strict dependency from lzo
zram: add stat to gather incompressible pages since zram set up
zram: support page writeback
mm/process_vm_access: remove redundant initialization of iov_r
mm/zsmalloc.c: rework the list_add code in insert_zspage()
mm/zswap: move to use crypto_acomp API for hardware acceleration
mm/zswap: fix passing zero to 'PTR_ERR' warning
mm/zswap: make struct kernel_param_ops definitions const
userfaultfd/selftests: hint the test runner on required privilege
userfaultfd/selftests: fix retval check for userfaultfd_open()
userfaultfd/selftests: always dump something in modes
userfaultfd: selftests: make __{s,u}64 format specifiers portable
...
See Documentation/core-api/printk-formats.rst.
h should no longer be used in the format specifier for printk.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
See Documentation/core-api/printk-formats.rst.
h should no longer be used in the format specifier for printk.
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is a spelling mistake in a comment in the Kconfig. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
We need to move the check under the non-headless case, otherwise
we always reserve the VGA save size.
Fixes: 157fe68d74 ("drm/amdgpu: fix size calculation with stolen vga memory")
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In Virtualization case, when one VF is sending too many
FLR requests, hypervisor would stop responding to this
VF's request for a long period of time. This is called
event guard. During this period of cooling time, guest
driver should wait instead of doing other things. After
this period of time, guest driver would resume reset
process and return to normal.
Currently, guest driver would wait 12 seconds and return fail
if it doesn't get response from host.
Solution: extend this waiting time in guest driver and poll
response periodically. Poll happens every 6 seconds and it will
last for 60 seconds.
v2: change the max repetition times from number to macro.
Signed-off-by: Jiange Zhao <Jiange.Zhao@amd.com>
Acked-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
it could also be insufficient vram that makes
amdgpu_amdkfd_reserve_mem_limit fail.
Signed-off-by: Yifan Zhang <yifan1.zhang@amd.com>
Reviewed-by: Felix Kuehling <Felix.Kuehling@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
So we know when it's enabled and what method we are using.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Simplify the logic in the runtime resume handling for
atpx
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Change it to check if the device has ACPI power resources.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Check if the device has ACPI power resources so we can
enable runtime pm if so.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
In preparation for systems that support d3cold on dGPUs
independent of PX/HG. No functional change intended.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Kernel test robot throws below warning ->
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5349:5:
warning: no previous prototype for 'amdgpu_dm_crtc_atomic_set_property'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5349:5:
warning: no previous prototype for function
'amdgpu_dm_crtc_atomic_set_property' [-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5373:5:
warning: no previous prototype for 'amdgpu_dm_crtc_atomic_get_property'
[-Wmissing-prototypes]
drivers/gpu/drm/amd/amdgpu/../display/amdgpu_dm/amdgpu_dm.c:5373:5:
warning: no previous prototype for function
'amdgpu_dm_crtc_atomic_get_property' [-Wmissing-prototypes]
As these functions are only used inside amdgpu_dm.c, these can be
made static.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
- Add new aux_channel_type
- Changed port_index to instance in dmub_cmd_dp_aux_control_data
- Change aux_return_code_type to sync up with driver
- param for ramping abm based on backlight level
Signed-off-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
The OGAM LUT precision was accumulating too much error
in the higher end.
[How]
Instead of calculating all points of the LUT in relation
to the previous ones, perform a full calculation in one
of the intermediate segments to stop error propagation.
Signed-off-by: Felipe Clark <Felipe.Clark@amd.com>
Reviewed-by: Krunoslav Kovac <Krunoslav.Kovac@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
FP2 is not double buffered and must wait for VACTIVE
before programming.
[How]
Only update when there is a full update we should
change FP2 to avoid delay every flip.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
For certain timings, Renoir may underflow due to sr exit
latency being too slow.
[How]
Updated wm table for renoir.
Signed-off-by: Jake Wang <haonan.wang2@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
race condition of programming FP2 wrt pipe locking
and vactive state can cause underflow/black screen
[How]
Enforce the FP2 is only programmed during vactive,
and unlock pipe soon afterwards.
Signed-off-by: Martin Leung <martin.leung@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
We are missing the DP info frame update on dcn30, and this will
lead to DP SDPs not being sent;
[How]
Add the DP info frame update for dcn30;
Signed-off-by: Leo (Hanghong) Ma <hanghong.ma@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
dcn30_link_encoder_validate_output_with_stream was a static function.
[How]
remove the static define and include it in the header.
Signed-off-by: Eric Bernstein <eric.bernstein@amd.com>
Reviewed-by: Dmytro Laktyushkin <Dmytro.Laktyushkin@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Find out when we try to disable CRC calculation,
crc generation is still enabled. Main reason is
that dc_stream_configure_crc() will never get
called when the source is AMDGPU_DM_PIPE_CRC_SOURCE_NONE.
[How]
Add checking condition that when source is
AMDGPU_DM_PIPE_CRC_SOURCE_NONE, we should also call
dc_stream_configure_crc() to disable crc calculation.
Also, clean up crc window when disable crc calculation.
Signed-off-by: Wayne Lin <Wayne.Lin@amd.com>
Reviewed-by: Nicholas Kazlauskas <Nicholas.Kazlauskas@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
Many VR headsets require a HSYNC width of 4, but DCN
has default minimum of 8.
[How]
Change the arbitrary minimum HSYNC width to 4 to match
DCN20.
Signed-off-by: Aric Cyr <aric.cyr@amd.com>
Reviewed-by: Charlene Liu <Charlene.Liu@amd.com>
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
some DP_SEC register defs and masks are missing.
[How]
add the missing defs and masks.
Signed-off-by: Max Tseng <chuan-yu.tseng@amd.com>
Reviewed-by: Anthony Koo <Anthony.Koo@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
There is a warning that triggers when pstate takes too long.
Pstate can take up to ~200us on Linux without hanging but
it is currently set to 40us.
[How]
Change the timeout for the warning to be 180us on Linux.
Signed-off-by: Victor Lu <victorchengchi.lu@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Qingqing Zhuo <qingqing.zhuo@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
skip load smu and sdma fw on sriov due to sos,
ta and asd fw have been skipped for SIENNA_CICHLID.
V2:
move asic check into smu11
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
CONFIG_DRM_AMD_DC_DCN3_0 is retired. drop it
Signed-off-by: Flora Cui <flora.cui@amd.com>
Reviewed-by: Guchun Chen <guchun.chen@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
S0ix only makes sense on APUs since they are part of the platform, so
only when the ASIC is APU should set amdgpu_acpi_is_s0ix_supported flag
to deal with the related situation.
Signed-off-by: Likun Gao <Likun.Gao@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Without doing the soft reset, register mmSDMA0_GFX_RB_WPTR's value could not be
reset to 0 when sdma block resumes. That would cause the ring buffer's read and
write pointers not equal and ring test fail. So add the soft reset step.
Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
These are supported by Sienna Cichlid and should be
taken into consideration during DS control.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is needed for Sienna Cichlid.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
This is needed for Sienna Cichlid.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fulfill the UMD PSTATE profiling clocks of sienna cichlid.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Driver code has no business with the internals of the irq descriptor.
Aside of that the count is per interrupt line and therefore takes
interrupts from other devices into account which share the interrupt line
and are not handled by the graphics driver.
Replace it with a pmu private count which only counts interrupts which
originate from the graphics card.
To avoid atomics or heuristics of some sort make the counter field
'unsigned long'. That limits the count to 4e9 on 32bit which is a lot and
postprocessing can easily deal with the occasional wraparound.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Link: https://lore.kernel.org/r/20201210194043.957046529@linutronix.de
Nothing uses the result and nothing should ever use it in driver code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: https://lore.kernel.org/r/20201210194043.862572239@linutronix.de
It can take multiple iterations until all components for an attached DSI
bridge are up leading to several:
[ 3.796425] mxsfb 30320000.lcd-controller: Cannot connect bridge: -517
[ 3.816952] mxsfb 30320000.lcd-controller: [drm:mxsfb_probe [mxsfb]] *ERROR* failed to attach bridge: -517
Silence this by checking for -EPROBE_DEFER and using dev_err_probe() so
we set a deferred reason in case a dependency fails to probe (which
quickly happens on small config/DT changes due to the rather long probe
chain which can include bridges, phys, panels, backights, leds, etc.).
This also removes the only DRM_DEV_ERROR() usage, the rest of the driver
uses dev_err().
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Fixes: c42001e357 ("drm: mxsfb: Use drm_panel_bridge")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/d5761eb871adde5464ba112b89d966568bc2ff6c.1608020391.git.agx@sigxcpu.org
- migrate_disable/enable() support which originates from the RT tree and
is now a prerequisite for the new preemptible kmap_local() API which aims
to replace kmap_atomic().
- A fair amount of topology and NUMA related improvements
- Improvements for the frequency invariant calculations
- Enhanced robustness for the global CPU priority tracking and decision
making
- The usual small fixes and enhancements all over the place
-----BEGIN PGP SIGNATURE-----
iQJHBAABCgAxFiEEQp8+kY+LLUocC4bMphj1TA10mKEFAl/XwK4THHRnbHhAbGlu
dXRyb25peC5kZQAKCRCmGPVMDXSYoX28D/9cVrvziSQGfBfuQWnUiw8iOIq1QBa2
Me+Tvenhfrlt7xU6rbP9ciFu7eTN+fS06m5uQPGI+t22WuJmHzbmw1bJVXfkvYfI
/QoU+Hg7DkDAn1p7ZKXh0dRkV0nI9ixxSHl0E+Zf1ATBxCUMV2SO85flg6z/4qJq
3VWUye0dmR7/bhtkIjv5rwce9v2JB2g1AbgYXYTW9lHVoUdGoMSdiZAF4tGyHLnx
sJ6DMqQ+k+dmPyYO0z5MTzjW/fXit4n9w2e3z9TvRH/uBu58WSW1RBmQYX6aHBAg
dhT9F4lvTs6lJY23x5RSFWDOv6xAvKF5a0xfb8UZcyH5EoLYrPRvm42a0BbjdeRa
u0z7LbwIlKA+RFdZzFZWz8UvvO0ljyMjmiuqZnZ5dY9Cd80LSBuxrWeQYG0qg6lR
Y2povhhCepEG+q8AXIe2YjHKWKKC1s/l/VY3CNnCzcd21JPQjQ4Z5eWGmHif5IED
CntaeFFhZadR3w02tkX35zFmY3w4soKKrbI4EKWrQwd+cIEQlOSY7dEPI/b5BbYj
MWAb3P4EG9N77AWTNmbhK4nN0brEYb+rBbCA+5dtNBVhHTxAC7OTWElJOC2O66FI
e06dREjvwYtOkRUkUguWwErbIai2gJ2MH0VILV3hHoh64oRk7jjM8PZYnjQkdptQ
Gsq0rJW5iiu/OQ==
=Oz1V
-----END PGP SIGNATURE-----
Merge tag 'sched-core-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull scheduler updates from Thomas Gleixner:
- migrate_disable/enable() support which originates from the RT tree
and is now a prerequisite for the new preemptible kmap_local() API
which aims to replace kmap_atomic().
- A fair amount of topology and NUMA related improvements
- Improvements for the frequency invariant calculations
- Enhanced robustness for the global CPU priority tracking and decision
making
- The usual small fixes and enhancements all over the place
* tag 'sched-core-2020-12-14' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (61 commits)
sched/fair: Trivial correction of the newidle_balance() comment
sched/fair: Clear SMT siblings after determining the core is not idle
sched: Fix kernel-doc markup
x86: Print ratio freq_max/freq_base used in frequency invariance calculations
x86, sched: Use midpoint of max_boost and max_P for frequency invariance on AMD EPYC
x86, sched: Calculate frequency invariance for AMD systems
irq_work: Optimize irq_work_single()
smp: Cleanup smp_call_function*()
irq_work: Cleanup
sched: Limit the amount of NUMA imbalance that can exist at fork time
sched/numa: Allow a floating imbalance between NUMA nodes
sched: Avoid unnecessary calculation of load imbalance at clone time
sched/numa: Rename nr_running and break out the magic number
sched: Make migrate_disable/enable() independent of RT
sched/topology: Condition EAS enablement on FIE support
arm64: Rebuild sched domains on invariance status changes
sched/topology,schedutil: Wrap sched domains rebuild
sched/uclamp: Allow to reset a task uclamp constraint value
sched/core: Fix typos in comments
Documentation: scheduler: fix information on arch SD flags, sched_domain and sched_debug
...
Reorder the code to fix checking if blitting is available.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 28a68f8282 ("drm/radeon/ttm: use multihop")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/403847/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorder the code to fix checking if blitting is available.
Signed-off-by: Christian König <christian.koenig@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Link: https://patchwork.freedesktop.org/patch/401019/
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reorder the code to fix checking if blitting is available.
Signed-off-by: Christian König <christian.koenig@amd.com>
Fixes: 28a68f8282 ("drm/radeon/ttm: use multihop")
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/403847/
Pull OPP (Operating Performance Points) updates for 5.11-rc1 from
Viresh Kumar:
"This contains the following updates:
- Allow empty (node-less) OPP tables in DT for passing just the
dependency related information (Nicola Mazzucato).
- Fix a potential lockdep in OPP core and other OPP core cleanups
(Viresh Kumar).
- Don't abuse dev_pm_opp_get_opp_table() to create an OPP table, fix
cpufreq-dt driver for the same (Viresh Kumar).
- dev_pm_opp_put_regulators() accepts a NULL argument now, updates to
all the users as well (Viresh Kumar)."
* 'opp/linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/vireshk/pm:
opp: of: Allow empty opp-table with opp-shared
dt-bindings: opp: Allow empty OPP tables
media: venus: dev_pm_opp_put_*() accepts NULL argument
drm/panfrost: dev_pm_opp_put_*() accepts NULL argument
drm/lima: dev_pm_opp_put_*() accepts NULL argument
PM / devfreq: exynos: dev_pm_opp_put_*() accepts NULL argument
cpufreq: qcom-cpufreq-nvmem: dev_pm_opp_put_*() accepts NULL argument
cpufreq: dt: dev_pm_opp_put_regulators() accepts NULL argument
opp: Allow dev_pm_opp_put_*() APIs to accept NULL opp_table
opp: Don't create an OPP table from dev_pm_opp_get_opp_table()
cpufreq: dt: Don't (ab)use dev_pm_opp_get_opp_table() to create OPP table
opp: Reduce the size of critical section in _opp_kref_release()
opp: Don't return opp_dev from _find_opp_dev()
opp: Allocate the OPP table outside of opp_table_lock
opp: Always add entries in dev_list with opp_table->lock held
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support
-----BEGIN PGP SIGNATURE-----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=c9rl
-----END PGP SIGNATURE-----
Merge tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm
Pull drm updates from Dave Airlie:
"Not a huge amount of big things here, AMD has support for a few new HW
variants (vangogh, green sardine, dimgrey cavefish), Intel has some
more DG1 enablement. We have a few big reworks of the TTM layers and
interfaces, GEM and atomic internal API reworks cross tree. fbdev is
marked orphaned in here as well to reflect the current reality.
core:
- documentation updates
- deprecate DRM_FORMAT_MOD_NONE
- atomic crtc enable/disable rework
- GEM convert drivers to gem object functions
- remove SCATTER_LIST_MAX_SEGMENT
sched:
- avoid infinite waits
ttm:
- remove AGP support
- don't modify caching for swapout
- ttm pinning rework
- major TTM reworks
- new backend allocator
- multihop support
vram-helper:
- top down BO placement fix
- TTM changes
- GEM object support
displayport:
- DP 2.0 DPCD prep work
- DP MST extended DPCD caps
fbdev:
- mark as orphaned
amdgpu:
- Initial Vangogh support
- Green Sardine support
- Dimgrey Cavefish support
- SG display support for renoir
- SMU7 improvements
- gfx9+ modiifier support
- CI BACO fixes
radeon:
- expose voltage via hwmon on SUMO
amdkfd:
- fix unique id handling
i915:
- more DG1 enablement
- bigjoiner support
- integer scaling filter support
- async flip support
- ICL+ DSI command mode
- Improve display shutdown
- Display refactoring
- eLLC machine fbdev loading fix
- dma scatterlist fixes
- TGL hang fixes
- eLLC display buffer caching on SKL+
- MOCS PTE seeting for gen9+
msm:
- Shutdown hook
- GPU cooling device support
- DSI 7nm and 10nm phy/pll updates
- sm8150/sm2850 DPU support
- GEM locking re-work
- LLCC system cache support
aspeed:
- sysfs output config support
ast:
- LUT fix
- new display mode
gma500:
- remove 2d framebuffer accel
panfrost:
- move gpu reset to a worker
exynos:
- new HDMI mode support
mediatek:
- MT8167 support
- yaml bindings
- MIPI DSI phy code moved
etnaviv:
- new perf counter
- more lockdep annotation
hibmc:
- i2c DDC support
ingenic:
- pixel clock reset fix
- reserved memory support
- allow both DMA channels at once
- different pixel format support
- 30/24/8-bit palette modes
tilcdc:
- don't keep vblank irq enabled
vc4:
- new maintainer added
- DSI registration fix
virtio:
- blob resource support
- host visible and cross-device support
- uuid api support"
* tag 'drm-next-2020-12-11' of git://anongit.freedesktop.org/drm/drm: (1754 commits)
drm/amdgpu: Initialise drm_gem_object_funcs for imported BOs
drm/amdgpu: fix size calculation with stolen vga memory
drm/amdgpu: remove amdgpu_ttm_late_init and amdgpu_bo_late_init
drm/amdgpu: free the pre-OS console framebuffer after the first modeset
drm/amdgpu: enable runtime pm using BACO on CI dGPUs
drm/amdgpu/cik: enable BACO reset on Bonaire
drm/amd/pm: update smu10.h WORKLOAD_PPLIB setting for raven
drm/amd/pm: remove one unsupported smu function for vangogh
drm/amd/display: setup system context for APUs
drm/amd/display: add S/G support for Vangogh
drm/amdkfd: Fix leak in dmabuf import
drm/amdgpu: use AMDGPU_NUM_VMID when possible
drm/amdgpu: fix sdma instance fw version and feature version init
drm/amd/pm: update driver if version for dimgrey_cavefish
drm/amd/display: 3.2.115
drm/amd/display: [FW Promotion] Release 0.0.45
drm/amd/display: Revert DCN2.1 dram_clock_change_latency update
drm/amd/display: Enable gpu_vm_support for dcn3.01
drm/amd/display: Fixed the audio noise during mode switching with HDCP mode on
drm/amd/display: Add wm table for Renoir
...
Register devfreq cooling device and attempt to register Energy Model. This
will add the devfreq device to the Energy Model framework. It will create
a dedicated and unified data structures used i.e. in thermal framework.
It uses simplified Energy Model, created based on voltage, frequency
and DT 'dynamic-power-coefficient'.
Reviewed-by: Steven Price <steven.price@arm.com>
Reviewed-by: Alyssa Rosenzweig <alyssa.rosenzweig@collabora.com>
Signed-off-by: Lukasz Luba <lukasz.luba@arm.com>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Link: https://lore.kernel.org/r/20201210143014.24685-6-lukasz.luba@arm.com
Reduce the module/device probe error into a mere debug to hide issues
where the initial modeset is failing (after lies told by hw probe) and
the system hangs with a livelock in cleaning up the failed commit.
Reported-by: H.J. Lu <hjl.tools@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=210619
Fixes: b3bf99daae ("drm/i915/display: Defer initial modeset until after GGTT is initialised")
Fixes: ccc9e67ab2 ("drm/i915/display: Defer initial modeset until after GGTT is initialised")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: "Ville Syrjälä" <ville.syrjala@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Dave Airlie <airlied@redhat.com>
Reviewed-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201210230741.17140-1-chris@chris-wilson.co.uk
- Check the correct variable in selftest (Dan)
- Propagate error from canceled submit due to context closure (Chris)
- Ignore repeated attempts to suspend request flow across reset (Chris)
- Cancel the preemption timeout on responding to it (Chris)
- Fix unsigned compared against 0 (Colin)
- Compute the correct slice count for VDSC on DP (Manasi)
- Declar gen9 has 64 mocs entries (Chris)
-----BEGIN PGP SIGNATURE-----
iQEzBAABCAAdFiEEbSBwaO7dZQkcLOKj+mJfZA7rE8oFAl/RYfgACgkQ+mJfZA7r
E8qAFAf+KdbI2Is7i8OdHOz5sP97QplFVn9JY3rfXbi+ekIvZD9F/9yLyoav2a5Q
SLScUMlxbXUMyBUav3gGxJLcSIyHZRdq75rlZ5zjcF7GaNUu+VBEahbPiQ2tLC5A
IO98SkHxktnHGyHQqELIH4vzm+3zwQhB8X4moob3bhAJPjSITQkUUsUNARljoSJ+
i0fYsh6QAmhzMTcSMaRQIgk7FJYvTk2//4BeD2viErnbjMqANg8hXcVN0UsWlVgO
OEj6QcIEOU9MWCkm57GmsjIjhYd18xg0IJ/OjJSl9S4mC2u89/ZEK6khr0+iJZE4
dIh5gZmCmkn2s3kfpzWaaVRej6R6SQ==
=1+fd
-----END PGP SIGNATURE-----
Merge tag 'drm-intel-fixes-2020-12-09' of git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Fixes for VDSC/DP, selftests, shmem_utils, preemption, submission, and gt reset:
- Check the correct variable in selftest (Dan)
- Propagate error from canceled submit due to context closure (Chris)
- Ignore repeated attempts to suspend request flow across reset (Chris)
- Cancel the preemption timeout on responding to it (Chris)
- Fix unsigned compared against 0 (Colin)
- Compute the correct slice count for VDSC on DP (Manasi)
- Declar gen9 has 64 mocs entries (Chris)
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rodrigo Vivi <rodrigo.vivi@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20201209235010.GA10554@intel.com
RLC is halted when system suspend/shutdown. However, due to DPM enabled, PMFW is
unaware of RLC being halted and will continue sending messages, which would
eventually cause an ACPI hang. Use the system_feature_control interface to
notify SMU the status of RLC (Normal/OFF) thus enable/disable DPM feature.
Signed-off-by: Xiaomeng Hou <Xiaomeng.Hou@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Reviewed-by: Lazar Lijo <Lijo.Lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's only used when CONFIG_DRM_AMD_DC_DCN is set. Fixes and set but
not used warning.
Acked-by: Evan Quan <evan.quan@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "COMPUTE" was wrongly spelled as "CUSTOM".
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Fulfill the 2nd usb2.0 port workaround for sienna cichlid.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The workaround is needed by sienna cichlid.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Used for determining 2ND_USB20PORT support from firmware_capability.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
That will help to determine whether 2ND_USB20_PORT workaround is
needed for Sienna Cichlid.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
New SMC message was introduced for gpo control on sienna cichlid.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct the power limit setting for SMU V11 asics.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Enable power source switch on Sienna Cichlid.
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Lijo Lazar <lijo.lazar@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Correct pipe offset calculation in is_pipe_enabled function,
it should be done in queues.
Signed-off-by: Jiansong Chen <Jiansong.Chen@amd.com>
Reviewed-by: Hawking Zhang <Hawking.Zhang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
After refactor our amdgpu_dm_atomic_commit, this function only invoke
drm_atomic_helper_commit. For this reason, this commit drops
amdgpu_dm_atomic_commit and add drm_atomic_helper_commit directly in the
atomic_commit hook.
v2: squash in warning fix (Alex)
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Rodrigo Siqueira <Rodrigo.Siqueira@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The text output should not be more than a page, so only print the first
32 page table entries.
If we need all of them we can still look into the binary trace.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Shashank Sharma <shashank.sharma@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
For BOs imported from outside of amdgpu, setting of amdgpu_gem_object_funcs
was missing in amdgpu_dma_buf_create_obj. Fix by refactoring BO creation
and amdgpu_gem_object_funcs setting into single function called
from both code paths.
Fixes: d693def4fd ("drm: Remove obsolete GEM and PRIME callbacks from struct drm_driver")
v2: Use use amdgpu_gem_object_create() directly
v3: fix warning
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
The "COMPUTE" was wrongly spelled as "CUSTOM".
Signed-off-by: Evan Quan <evan.quan@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org # 5.9.x
* Shutdown hook for GPU (to ensure GPU is idle before iommu goes away)
* GPU cooling device support
* DSI 7nm and 10nm phy/pll updates
* Additional sm8150/sm8250 DPU support (merge_3d and DSPP color
processing)
* Various DP fixes
* A whole bunch of W=1 fixes from Lee Jones
* GEM locking re-work (no more trylock_recursive in shrinker!)
* LLCC (system cache) support
* Various other fixes/cleanups
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Rob Clark <robdclark@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/CAF6AEGt0G=H3_RbF_GAQv838z5uujSmFd+7fYhL6Yg=23LwZ=g@mail.gmail.com
For BOs imported from outside of amdgpu, setting of amdgpu_gem_object_funcs
was missing in amdgpu_dma_buf_create_obj. Fix by refactoring BO creation
and amdgpu_gem_object_funcs setting into single function called
from both code paths.
Fixes: d693def4fd ("drm: Remove obsolete GEM and PRIME callbacks from struct drm_driver")
v2: Use use amdgpu_gem_object_create() directly
v3: fix warning
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Andrey Grodzovsky <andrey.grodzovsky@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If we need to keep the stolen vga memory, make sure it is
at least as big as the legacy vga size.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When using old WORKLOAD_PPLIB setting in smu10.h, there is problem that
it can't be able to switch to mak gpu clk during compute workload.
It needs to update WORKLOAD_PPLIB setting to fix this issue.
Signed-off-by: Changfeng <Changfeng.Zhu@amd.com>
Reviewed-by: Huang Rui <ray.huang@amd.com>
Acked-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Release dmabuf reference before returning from kfd_ioctl_import_dmabuf.
amdgpu_amdkfd_gpuvm_import_dmabuf takes a reference to the underlying
GEM BO and doesn't keep the reference to the dmabuf wrapper.
Signed-off-by: Felix Kuehling <Felix.Kuehling@amd.com>
Reviewed-by: Kent Russell <kent.russell@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
each sdma instance fw_version and feature_version
should be set right value when asic type isn't
between SIENNA_CICHILD and CHIP_DIMGREY_CAVEFISH
Signed-off-by: Stanley.Yang <Stanley.Yang@amd.com>
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
[Why]
Without additional HostVM Latency, Renoir takes 2us longer to exit
self-refresh. This causes underflow in certain cases.
[How]
Add table for Renoir with updated sr exit latencies for WM set A.
Signed-off-by: Sung Lee <sung.lee@amd.com>
Reviewed-by: Yongqiang Sun <yongqiang.sun@amd.com>
Reviewed-by: Roman Li <Roman.Li@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
[Why]
At very high pixel clock, bandwidth calculation exceeds 32 bit size
and overflow value. This causes the resulting selection of link rate
to be inaccurate.
[How]
Change order of operation and use fixed point to deal with integer
accuracy. Also address bug found when forcing link rate.
Signed-off-by: Chris Park <Chris.Park@amd.com>
Reviewed-by: Wenjing Liu <Wenjing.Liu@amd.com>
Acked-by: Eryk Brol <eryk.brol@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
There is still a warning when CONFIG_DEBUG_FS is disabled:
drivers/gpu/drm/amd/amdgpu/amdgpu_ras.c:1145:13: error: 'amdgpu_ras_debugfs_create_ctrl_node' defined but not used [-Werror=unused-function]
1145 | static void amdgpu_ras_debugfs_create_ctrl_node(struct amdgpu_device *adev)
Change the code again to make the compiler actually drop
this code but not warn about it.
Fixes: ae2bf61ff3 ("drm/amdgpu: guard ras debugfs creation/removal based on CONFIG_DEBUG_FS")
Reviewed-by: Tao Zhou <tao.zhou1@amd.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
To avoid a recently added warning:
Bogus possible_crtcs: [ENCODER:65:TMDS-65] possible_crtcs=0xf (full crtc mask=0x7)
WARNING: CPU: 3 PID: 439 at drivers/gpu/drm/drm_mode_config.c:617 drm_mode_config_validate+0x178/0x200 [drm]
In this case the warning is harmless, but confusing to users.
Fixes: 0df1082374 ("drm: Validate encoder->possible_crtcs")
Bug: https://bugzilla.kernel.org/show_bug.cgi?id=209123
Reviewed-by: Daniel Vetter <daniel@ffwll.ch>
Reviewed-by: Nicholas Kazlauskas <nicholas.kazlauskas@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
The dev_pm_opp_put_*() APIs now accepts a NULL opp_table pointer and so
there is no need for us to carry the extra check. Drop them.
Reviewed-by: Steven Price <steven.price@arm.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
The dev_pm_opp_put_*() APIs now accepts a NULL opp_table pointer and so
there is no need for us to carry the extra check. Drop them.
Reviewed-by: Qiang Yu <yuq825@gmail.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
If we need to keep the stolen vga memory, make sure it is
at least as big as the legacy vga size.
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
John Clements