A variable dma_stop_delay is added as a new member in hdac_bus
structure to avoid memory decode error incase DMA RUN bit is not
disabled in the given timeout from snd_hdac_stream_sync function and
followed by stream reset which results in memory decode error between
reset set and clear operation.
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20200805095221.5476-3-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Stripe control programming is governed by following formula, which is
referenced from the HD Audio specification(Revision 1.0a).
{ ((num_channels * bits_per_sample) / number of SDOs) >= 8 }
Currently above is implemented in snd_hdac_get_stream_stripe_ctl().
This patch introduces a structure member to store the default factor
of '8'. If any HW wants to use a different value, this member can be
easily updated.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Link: https://lore.kernel.org/r/1588580176-2801-3-git-send-email-spujar@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tegra HDA has FIFO size which can hold upto 10 audio frames to support
DVFS. When HDA DMA RUN bit is set to 0 to stop the stream, the DMA RUN
bit will be cleared to 0 only after transferring all the remaining audio
frames queued up in the fifo. This is not in sync with spec which states
the controller will stop transmitting(output) in the beginning of the
next frame for the relevant stream.
The above behavior with Tegra HDA was resulting in machine check error
during the system suspend flow with active audio playback with below kernel
error logs.
[ 33.524583] mc-err: [mcerr] (hda) csr_hdar: EMEM address decode error
[ 33.531088] mc-err: [mcerr] status = 0x20000015; addr = 0x00000000
[ 33.537431] mc-err: [mcerr] secure: no, access-type: read, SMMU fault: none
This was due to the fifo has more than one audio frame when the DMA
RUN bit is set to 0 during system suspend flow and the timeout handling in
snd_hdac_stream_sync() was not designed to handle this scenario. So the
DMA will continue running even after timeout hit until all remaining
audio frames in the fifo are transferred, but the suspend flow will try
to reset the controller and turn off the hda clocks without the knowledge
of the DMA is still running and could result in mc-err.
The above issue can be resolved by doing stream reset with the help of
snd_hdac_stream_reset() which would ensure the DMA RUN bit is cleared
if the timeout was hit in snd_hdac_stream_sync().
Signed-off-by: Mohan Kumar <mkumard@nvidia.com>
Link: https://lore.kernel.org/r/20200128051508.26064-1-mkumard@nvidia.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Make W=1 throws a lot of warnings, with multiple misalignments between
function params and their descriptions.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Link: https://lore.kernel.org/r/20200113205638.27338-1-pierre-louis.bossart@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit e38e486d66 ("ALSA: hda: Modify stream stripe mask only
when needed") tried to address the regression by the unconditional
application of the stripe mask, but this caused yet another
regression for the previously working devices. Namely, the patch
clears the azx_dev->stripe flag at snd_hdac_stream_clear(), but this
may be called multiple times before restarting the stream, so this
ended up with clearance of the flag for the whole time.
This patch fixes the regression by moving the azx_dev->stripe flag
clearance at the counter-part, the close callback of HDMI codec
driver instead.
Fixes: e38e486d66 ("ALSA: hda: Modify stream stripe mask only when needed")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=205855
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204477
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191214175217.31852-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent commit in HD-audio stream management for changing the
stripe control seems causing a regression on some platforms. The
stripe control is currently used only by HDMI codec, and applying the
stripe mask unconditionally may lead to scratchy and static noises as
seen on some MacBooks.
For addressing the regression, this patch changes the stream
management code to apply the stripe mask conditionally only when the
codec driver requested.
Fixes: 9b6f7e7a29 ("ALSA: hda: program stripe bits for controller")
BugLink: https://bugzilla.kernel.org/show_bug.cgi?id=204477
Tested-by: Michael Pobega <mpobega@neverware.com>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20191202074947.1617-1-tiwai@suse.de
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently we set hdac_stream.fifo_size field only for the playback
stream by some odd reason I forgot, while this field isn't referred in
any places. Actually this fifo_size field would have been required in
the position report correction for VIA chipset, but due to the lack of
the fifo_size set for capture streams, snd-hda-intel driver fetches
the register by itself.
This patch straightens and simplifies the code by setting the
fifo_size field for both playback and capture streams, and use it in
the HD-audio controller driver.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The HD-audio core allocates and releases pages via driver's specific
dma_alloc_pages and dma_free_pages ops defined in bus->io_ops. This
was because some platforms require the uncached pages and the handling
of page flags had to be done locally in the driver code.
Since the recent change in ALSA core memory allocator, we can simply
pass SNDRV_DMA_TYPE_DEV_UC for the uncached pages, and the only
difference became about this type to be passed to the core allocator.
That is, it's good time for cleaning up the mess.
This patch changes the allocation code in HD-audio core to call the
core allocator directly so that we get rid of dma_alloc_pages and
dma_free_pages io_ops. If a driver needs the uncached pages, it has
to set bus->dma_type right after the bus initialization.
This is merely a code refactoring and shouldn't bring any behavior
changes.
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Platforms having multiple SORs and hdmi/dp sinks require higher
bandwidth to support simultaneous playbacks of higher resolution.
If hda controller supports multiple SDO lines, STRIPE can be used
to indicate how many of the SDO lines the stream should be striped
across.
During stream start stripe control bits are programmed to use given
number of sdo lines and the same is cleared during stream stop.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Ravindra Lokhande <rlokhande@nvidia.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Controllers and codecs can support striping of audio out across
multiple SDO lines. The number of supported SDO lines can be
specific to chip. GCAP register can be read to know the maximum
supported SDO lines.
snd_hdac_get_stream_stripe_ctl() is exposed to program stripe bits
on controller and codec side.
stripe value: 0 for 1SDO, 1 for 2SDO, 2 for 4SDO lines, etc.,
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Reviewed-by: Mohan Kumar D <mkumard@nvidia.com>
Reviewed-by: Ravindra Lokhande <rlokhande@nvidia.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To enable SIE(Stream Interrupt Enable) in snd_hdac_stream_start(), we
should set both mask and value to be "1 << azx_dev->index" for register
update, the mask was 0, here fix it.
Signed-off-by: Keyon Jie <yang.jie@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The BDL pointer used in snd_hdac_dsp_prepare() should be declared as
__le32, as warned by sparse:
sound/hda/hdac_stream.c:655:47: warning: incorrect type in argument 4 (different base types)
sound/hda/hdac_stream.c:655:47: expected restricted __le32 [usertype] **bdlp
sound/hda/hdac_stream.c:655:47: got unsigned int [usertype] **<noident>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The macros _snd_hdac_chip_read() and *_write() expand to different
types (b,w,l) per their argument. They were thought to be used only
internally for other snd_hdac_chip_*() macros, but in some situations
we need to call these directly, and they are way too ugly.
Instead of saving a few lines, we just write these macros explicitly
with the types, so that they can be used in a saner way.
Acked-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
Give some readable comment in kernel doc style for each exported
function, as I promised in the previous meetings. While we're at it,
fix the wrong comments, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a helper to find the stream using stream tag and direction.
This is useful for drivers to query stream based on stream tag
and direction, fox example while downloading FW thru DSP loader
code
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CA0132 DSP loader leads to NULL deference since the recent
transition to HDA core code, as it unconditionally accesses
hdac_stream->substream->runtime. For DSP loading, the substream
shouldn't be assigned.
This patch addresses the NULL dereference above in addition to assure
the substream is cleared while DSP loading.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=98151
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the trace of snd_hdac_stream_start and snd_hdac_stream_stop.
Signed-off-by: Libin Yang <libin.yang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This will be used by hda controller driver to
setup stream params in prepare. This function will
setup the bdl and periods.
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Subhransu S. Prusty <subhransu.s.prusty@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For fixing randconfig build errors like:
sound/hda/hdac_stream.c: In function 'azx_timecounter_init':
sound/hda/hdac_stream.c:365:2: error: implicit declaration of function 'CLOCKSOURCE_MASK' [-Werror=implicit-function-declaration]
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the controller helper codes to hda-core library.
The I/O access ops are added to the bus ops. The CORB/RIRB, the basic
attributes like irq# and iomap address, some locks and the list of
streams are added to the bus object, together with the stream object
and its helpers.
Currently the codes are just copied from the legacy driver, so you can
find duplicated codes in both directories. Only constants are removed
from the original hda_controller.h. More integration work will follow
in the later patches.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
huangjianghui