This patch adds support for Serval pinctrl, using the ocelot driver as
basis. It adds pinconfig support as well, as supported by the
platform.
gclement: Split from a larger patch adding support all platforms in
the same time.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20201106093118.965152-5-gregory.clement@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds support for Luton pinctrl, using the ocelot driver as
basis. It adds pinconfig support as well, as supported by the
platform.
gclement: Split from a larger patch adding support all platforms in
the same time.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Link: https://lore.kernel.org/r/20201106093118.965152-4-gregory.clement@bootlin.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This add support for Sparx5 pinctrl, using the ocelot drives as
basis. It adds pinconfig support as well, as supported by the
platform.
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20200615133242.24911-6-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes a problem with using the GPIO as an interrupt on Jaguar2
(and similar), as the register layout of the platforms with 64 GPIO's
are pairwise, such that the original offset must be multiplied with
the platform stride.
Fixes: da801ab56a pinctrl: ocelot: add MSCC Jaguar2 support.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-4-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This patch removes the instance number from the "miim", "reco_clk" and
"sfp" pin function.
The change needed is to prepare the driver for adding new platforms
with more of these instances. The instance number is also redundant,
as this is implicit for each pin.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-3-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This fixes the situation where the GPIO controller is not
used as an interrupt controller as well.
Previously, the driver would silently fail to register even the
GPIO's. With this change, the driver will only register as an
interrupt controller if a parent interrupt is provided.
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Link: https://lore.kernel.org/r/20200513125532.24585-2-lars.povlsen@microchip.com
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Use newly added GPIO defines GPIO_LINE_DIRECTION_IN and
GPIO_LINE_DIRECTION_OUT instead of using hard-coded 1 and 0.
Main benefit is to make it easier to see which values mean IN and which
OUT. As a side effect this helps GPIO framework to change the direction
defines to something else if ever needed.
Please note that return value from get_direction call on
pinctrl-axp209 driver was changed. Previously pinctrl-axp209 might have
returned value 2 for direction INPUT.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Reported-by: kbuild test robot <lkp@intel.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Link: https://lore.kernel.org/r/20200214135712.GA14557@localhost.localdomain
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We need to convert all old gpio irqchips to pass the irqchip
setup along when adding the gpio_chip. For more info see
drivers/gpio/TODO.
For chained irqchips this is a pretty straight-forward
conversion.
Cc: Thierry Reding <thierry.reding@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Link: https://lore.kernel.org/r/20191002114454.9684-1-linus.walleij@linaro.org
The actual layout for OCELOT_GPIO_ALT[01] when there are more than 32 pins
is interleaved, i.e. OCELOT_GPIO_ALT0[0], OCELOT_GPIO_ALT1[0],
OCELOT_GPIO_ALT0[1], OCELOT_GPIO_ALT1[1]. Introduce a new REG_ALT macro to
facilitate the register offset calculation and use it where necessary.
Fixes: da801ab56a pinctrl: ocelot: add MSCC Jaguar2 support
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The third argument passed to REG is not the correct one and
ocelot_gpio_set_direction is not working for pins after 31. Fix that by
passing the pin number instead of the modulo 32 value.
Fixes: da801ab56a pinctrl: ocelot: add MSCC Jaguar2 support
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Jaguar2 has the same register layout as Ocelot but it has 64 pins, meaning
that there are 2 registers instead of one.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This GPIO controller can serve as an interrupt controller as well on the
GPIOs it handles.
An interrupt is generated whenever a GPIO line changes and the
interrupt for this GPIO line is enabled. This means that both the
changes from low to high and high to low generate an interrupt.
For some use cases, it makes sense to ignore the high to low change and
not generate an interrupt. Such a use case is a line that is hold in a
level high/low manner until the event holding the line gets acked.
This can be achieved by making sure the interrupt on the GPIO controller
side gets acked and masked only after the line gets hold in its default
state, this is what's done with the fasteoi functions.
Only IRQ_TYPE_EDGE_BOTH and IRQ_TYPE_LEVEL_HIGH are supported for now.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
the TWI function on GPIO4 is actually a multiplexed SCL, not an original
TWI SDA or SCL. Fix it.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Bits have to be cleared in DEVCPU_GCB:GPIO:GPIO_OE for input and set for
output. ocelot_gpio_set_direction() got it wrong and this went unnoticed
when the driver was reworked.
Reported-by: Gregory Clement <gregory.clement@bootlin.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Acked-by: Gregory CLEMENT <gregory.clement@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The function ocelot_pinctrl_probe is local to the source and does not
need to be in global scope, so make it static.
Cleans up sparse warning:
drivers/pinctrl/pinctrl-ocelot.c:465:5: warning: symbol
'ocelot_pinctrl_probe' was not declared. Should it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The Microsemi Ocelot SoC has a few pins that can be used as GPIOs or take
multiple other functions. Add a driver for the pinmuxing and the GPIOs.
There is currently no support for interrupts.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Lars Povlsen