Rob suggests to move of_net.c from under drivers/of/ somewhere
to the networking code.
Suggested-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The felix DSA driver, which is a wrapper over the same hardware class as
ocelot, is integrated with phylink, but ocelot is using the plain PHY
library. It makes sense to bring together the two implementations, which
is what this patch achieves.
This is a large patch and hard to break up, but it does the following:
The existing ocelot_adjust_link writes some registers, and
felix_phylink_mac_link_up writes some registers, some of them are
common, but both functions write to some registers to which the other
doesn't.
The main reasons for this are:
- Felix switches so far have used an NXP PCS so they had no need to
write the PCS1G registers that ocelot_adjust_link writes
- Felix switches have the MAC fixed at 1G, so some of the MAC speed
changes actually break the link and must be avoided.
The naming conventions for the functions introduced in this patch are:
- vsc7514_phylink_{mac_config,validate} are specific to the Ocelot
instantiations and placed in ocelot_net.c which is built only for the
ocelot switchdev driver.
- ocelot_phylink_mac_link_{up,down} are shared between the ocelot
switchdev driver and the felix DSA driver (they are put in the common
lib).
One by one, the registers written by ocelot_adjust_link are:
DEV_MAC_MODE_CFG - felix_phylink_mac_link_up had no need to write this
register since its out-of-reset value was fine and
did not need changing. The write is moved to the
common ocelot_phylink_mac_link_up and on felix it is
guarded by a quirk bit that makes the written value
identical with the out-of-reset one
DEV_PORT_MISC - runtime invariant, was moved to vsc7514_phylink_mac_config
PCS1G_MODE_CFG - same as above
PCS1G_SD_CFG - same as above
PCS1G_CFG - same as above
PCS1G_ANEG_CFG - same as above
PCS1G_LB_CFG - same as above
DEV_MAC_ENA_CFG - both ocelot_adjust_link and ocelot_port_disable
touched this. felix_phylink_mac_link_{up,down} also
do. We go with what felix does and put it in
ocelot_phylink_mac_link_up.
DEV_CLOCK_CFG - ocelot_adjust_link and felix_phylink_mac_link_up both
write this, but to different values. Move to the common
ocelot_phylink_mac_link_up and make sure via the quirk
that the old values are preserved for both.
ANA_PFC_PFC_CFG - ocelot_adjust_link wrote this, felix_phylink_mac_link_up
did not. Runtime invariant, speed does not matter since
PFC is disabled via the RX_PFC_ENA bits which are cleared.
Move to vsc7514_phylink_mac_config.
QSYS_SWITCH_PORT_MODE_PORT_ENA - both ocelot_adjust_link and
felix_phylink_mac_link_{up,down} wrote
this. Ocelot also wrote this register
from ocelot_port_disable. Keep what
felix did, move in ocelot_phylink_mac_link_{up,down}
and delete ocelot_port_disable.
ANA_POL_FLOWC - same as above
SYS_MAC_FC_CFG - same as above, except slight behavior change. Whereas
ocelot always enabled RX and TX flow control, felix
listened to phylink (for the most part, at least - see
the 2500base-X comment).
The registers which only felix_phylink_mac_link_up wrote are:
SYS_PAUSE_CFG_PAUSE_ENA - this is why I am not sure that flow control
worked on ocelot. Not it should, since the
code is shared with felix where it does.
ANA_PORT_PORT_CFG - this is a Frame Analyzer block register, phylink
should be the one touching them, deleted.
Other changes:
- The old phylib registration code was in mscc_ocelot_init_ports. It is
hard to work with 2 levels of indentation already in, and with hard to
follow teardown logic. The new phylink registration code was moved
inside ocelot_probe_port(), right between alloc_etherdev() and
register_netdev(). It could not be done before (=> outside of)
ocelot_probe_port() because ocelot_probe_port() allocates the struct
ocelot_port which we then use to assign ocelot_port->phy_mode to. It
is more preferable to me to have all PHY handling logic inside the
same function.
- On the same topic: struct ocelot_port_private :: serdes is only used
in ocelot_port_open to set the SERDES protocol to Ethernet. This is
logically a runtime invariant and can be done just once, when the port
registers with phylink. We therefore don't even need to keep the
serdes reference inside struct ocelot_port_private, or to use the devm
variant of of_phy_get().
- Phylink needs a valid phy-mode for phylink_create() to succeed, and
the existing device tree bindings in arch/mips/boot/dts/mscc/ocelot_pcb120.dts
don't define one for the internal PHY ports. So we patch
PHY_INTERFACE_MODE_NA into PHY_INTERFACE_MODE_INTERNAL.
- There was a strategically placed:
switch (priv->phy_mode) {
case PHY_INTERFACE_MODE_NA:
continue;
which made the code skip the serdes initialization for the internal
PHY ports. Frankly that is not all that obvious, so now we explicitly
initialize the serdes under an "if" condition and not rely on code
jumps, so everything is clearer.
- There was a write of OCELOT_SPEED_1000 to DEV_CLOCK_CFG for QSGMII
ports. Since that is in fact the default value for the register field
DEV_CLOCK_CFG_LINK_SPEED, I can only guess the intention was to clear
the adjacent fields, MAC_TX_RST and MAC_RX_RST, aka take the port out
of reset, which does match the comment. I don't even want to know why
this code is placed there, but if there is indeed an issue that all
ports that share a QSGMII lane must all be up, then this logic is
already buggy, since mscc_ocelot_init_ports iterates using
for_each_available_child_of_node, so nobody prevents the user from
putting a 'status = "disabled";' for some QSGMII ports which would
break the driver's assumption.
In any case, in the eventuality that I'm right, we would have yet
another issue if ocelot_phylink_mac_link_down would reset those ports
and that would be forbidden, so since the ocelot_adjust_link logic did
not do that (maybe for a reason), add another quirk to preserve the
old logic.
The ocelot driver teardown goes through all ports in one fell swoop.
When initialization of one port fails, the ocelot->ports[port] pointer
for that is reset to NULL, and teardown is done only for non-NULL ports,
so there is no reason to do partial teardowns, let the central
mscc_ocelot_release_ports() do its job.
Tested bind, unbind, rebind, link up, link down, speed change on mock-up
hardware (modified the driver to probe on Felix VSC9959). Also
regression tested the felix DSA driver. Could not test the Ocelot
specific bits (PCS1G, SERDES, device tree bindings).
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The premise of this change is that the switchdev port attributes and
objects offloaded by ocelot might have been missed when we are joining
an already existing bridge port, such as a bonding interface.
The patch pulls these switchdev attributes and objects from the bridge,
on behalf of the 'bridge port' net device which might be either the
ocelot switch interface, or the bonding upper interface.
The ocelot_net.c belongs strictly to the switchdev ocelot driver, while
ocelot.c is part of a library shared with the DSA felix driver.
The ocelot_port_bridge_leave function (part of the common library) used
to call ocelot_port_vlan_filtering(false), something which is not
necessary for DSA, since the framework deals with that already there.
So we move this function to ocelot_switchdev_unsync, which is specific
to the switchdev driver.
The code movement described above makes ocelot_port_bridge_leave no
longer return an error code, so we change its type from int to void.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this option, the driver fails to link:
ld.lld: error: undefined symbol: devlink_sb_register
>>> referenced by ocelot_devlink.c
>>> net/ethernet/mscc/ocelot_devlink.o:(ocelot_devlink_sb_register) in archive drivers/built-in.a
>>> referenced by ocelot_devlink.c
>>> net/ethernet/mscc/ocelot_devlink.o:(ocelot_devlink_sb_register) in archive drivers/built-in.a
Fixes: f59fd9cab7 ("net: mscc: ocelot: configure watermarks using devlink-sb")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210225143910.3964364-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Ocelot now uses include/linux/dsa/ocelot.h which makes use of
CONFIG_PACKING to pack/unpack bits into the Injection/Extraction Frame
Headers. So it needs to explicitly select it, otherwise there might be
build errors due to the missing dependency.
Fixes: 40d3f295b5 ("net: mscc: ocelot: use common tag parsing code with DSA")
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Having the users of MSCC_OCELOT_SWITCH_LIB depend on REGMAP_MMIO was a
bad idea, since that symbol is not user-selectable. So we should have
kept a 'select REGMAP_MMIO'.
When we do that, we run into 2 more problems:
- By depending on GENERIC_PHY, we are causing a recursive dependency.
But it looks like GENERIC_PHY has no other dependencies, and other
drivers select it, so we can select it too:
drivers/of/Kconfig:69:error: recursive dependency detected!
drivers/of/Kconfig:69: symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:68: symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7: symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by MSCC_OCELOT_SWITCH_LIB
drivers/net/ethernet/mscc/Kconfig:15: symbol MSCC_OCELOT_SWITCH_LIB is selected by MSCC_OCELOT_SWITCH
drivers/net/ethernet/mscc/Kconfig:22: symbol MSCC_OCELOT_SWITCH depends on GENERIC_PHY
drivers/phy/Kconfig:8: symbol GENERIC_PHY is selected by PHY_BCM_NS_USB3
drivers/phy/broadcom/Kconfig:41: symbol PHY_BCM_NS_USB3 depends on MDIO_BUS
drivers/net/phy/Kconfig:13: symbol MDIO_BUS depends on MDIO_DEVICE
drivers/net/phy/Kconfig:6: symbol MDIO_DEVICE is selected by PHYLIB
drivers/net/phy/Kconfig:254: symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:19: symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:25: symbol ARC_EMAC depends on OF_IRQ
- By depending on PHYLIB, we are causing a recursive dependency. PHYLIB
only has a single dependency, "depends on NETDEVICES", which we are
already depending on, so we can again hack our way into conformance by
turning the PHYLIB dependency into a select.
drivers/of/Kconfig:69:error: recursive dependency detected!
drivers/of/Kconfig:69: symbol OF_IRQ depends on IRQ_DOMAIN
kernel/irq/Kconfig:68: symbol IRQ_DOMAIN is selected by REGMAP
drivers/base/regmap/Kconfig:7: symbol REGMAP default is visible depending on REGMAP_MMIO
drivers/base/regmap/Kconfig:39: symbol REGMAP_MMIO is selected by MSCC_OCELOT_SWITCH_LIB
drivers/net/ethernet/mscc/Kconfig:15: symbol MSCC_OCELOT_SWITCH_LIB is selected by MSCC_OCELOT_SWITCH
drivers/net/ethernet/mscc/Kconfig:22: symbol MSCC_OCELOT_SWITCH depends on PHYLIB
drivers/net/phy/Kconfig:254: symbol PHYLIB is selected by ARC_EMAC_CORE
drivers/net/ethernet/arc/Kconfig:19: symbol ARC_EMAC_CORE is selected by ARC_EMAC
drivers/net/ethernet/arc/Kconfig:25: symbol ARC_EMAC depends on OF_IRQ
Fixes: f4d0323bae ("net: mscc: ocelot: convert MSCC_OCELOT_SWITCH into a library")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Putting 'ocelot' in the config's name twice just to say that 'it's the
ocelot driver running on the ocelot SoC' is a bit confusing. Instead,
it's just the ocelot driver. Now that we've renamed the previous symbol
that was holding the MSCC_OCELOT_SWITCH_OCELOT into *_LIB (because
that's what it is), we're free to use this name for the driver.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hide the CONFIG_MSCC_OCELOT_SWITCH option from users. It is meant to be
only a hardware library which is selected by the drivers that use it
(ocelot, felix).
Since it is "selected" from Kconfig, all its dependencies are manually
transferred to the driver that selects it. This is because "select" in
Kconfig language is a bit of a mess, and doesn't handle dependencies of
selected options quite right.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, the SerDes muxing was hardcoded to a given mode in the MAC
controller driver. Now, the SerDes muxing is configured within the
Device Tree and is enforced in the MAC controller driver so we can have
a lot of different SerDes configurations.
Make use of the SerDes PHYs in the MAC controller to set up the SerDes
according to the SerDes<->switch port mapping and the communication mode
with the Ethernet PHY.
Signed-off-by: Quentin Schulz <quentin.schulz@bootlin.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a driver for Microsemi Ocelot Ethernet switch support.
This makes two modules:
mscc_ocelot_common handles all the common features that doesn't depend on
how the switch is integrated in the SoC. Currently, it handles offloading
bridging to the hardware. ocelot_io.c handles register accesses. This is
unfortunately needed because the register layout is packed and then depends
on the number of ports available on the switch. The register definition
files are automatically generated.
ocelot_board handles the switch integration on the SoC and on the board.
Frame injection and extraction to/from the CPU port is currently done using
register accesses which is quite slow. DMA is possible but the port is not
able to absorb the whole switch bandwidth.
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jakub Kicinski