The cur_tx counter must be incremented after TACT bit of
txdesc->status was set. However, a CPU is possible to reorder
instructions and/or memory accesses between cur_tx and
txdesc->status. And then, if TX interrupt happened at such a
timing, the sh_eth_tx_free() may free the descriptor wrongly.
So, add wmb() before cur_tx++.
Otherwise NETDEV WATCHDOG timeout is possible to happen.
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reset support is present on R-Car. Let's support it, if it is
available.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The E-MAC IP on the R-Car AVB module has different initialization
parameters for RX frame size, duplex settings, different offset
for transfer speed setting and has magic packet detection support
compared to E-MAC on RZ/G2L Gigabit Ethernet module. Factorise
the ravb_emac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMAC IP on the R-Car AVB module has different initialization
parameters for RCR, TGC, TCCR, RIC0, RIC2, and TIC compared to
DMAC IP on the RZ/G2L Gigabit Ethernet module. Factorise the
ravb_dmac_init function to support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RZ/G2L supports HW checksum on RX and TX whereas R-Car supports on RX.
Factorise ravb_set_features to support this feature.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car supports 100 and 1000 Mbps transfer speed whereas RZ/G2L
in addition support 10Mbps. Factorise ravb_adjust_link function
in order to support 10Mbps speed.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car uses an extended descriptor in RX whereas, RZ/G2L uses
normal descriptor in RX. Factorise the ravb_rx function to
support the later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ravb_ring_init function uses an extended descriptor in RX for
R-Car and normal descriptor for RZ/G2L. Add a helper function
for RX ring buffer allocation to support later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ravb_ring_format function uses an extended descriptor in RX
for R-Car compared to the normal descriptor for RZ/G2L. Factorise
RX ring buffer buildup to extend the support for later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car uses extended descriptor in RX, whereas RZ/G2L uses normal
descriptor. Factorise ravb_ring_free function so that it can
support later SoC.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some H/W differences for the gPTP feature between
R-Car Gen3, R-Car Gen2, and RZ/G2L as below.
1) On R-Car Gen3, gPTP support is active in config mode.
2) On R-Car Gen2, gPTP support is not active in config mode.
3) RZ/G2L does not support the gPTP feature.
Add a ptp_cfg_active hw feature bit to struct ravb_hw_info for
supporting gPTP active in config mode for R-Car Gen3.
This patch also removes enum ravb_chip_id, chip_id from both
struct ravb_hw_info and struct ravb_private, as it is unused.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some H/W differences for the gPTP feature between
R-Car Gen3, R-Car Gen2, and RZ/G2L as below.
1) On R-Car Gen2, gPTP support is not active in config mode.
2) On R-Car Gen3, gPTP support is active in config mode.
3) RZ/G2L does not support the gPTP feature.
Add a no_ptp_cfg_active hw feature bit to struct ravb_hw_info for
handling gPTP for R-Car Gen2.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car Gen3 supports separate interrupts for E-MAC and DMA queues,
whereas R-Car Gen2 and RZ/G2L have a single interrupt instead.
Add a multi_irq hw feature bit to struct ravb_hw_info to enable
this only for R-Car Gen3.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For addressing 4 bytes alignment restriction on transmission
buffer for R-Car Gen2 we use 2 descriptors whereas it is a single
descriptor for other cases.
Replace the macros NUM_TX_DESC_GEN[23] with magic number and
add a comment to explain it.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register for retrieving TX counters is present only on R-Car Gen3
and RZ/G2L; it is not present on R-Car Gen2.
Add the tx_counters hw feature bit to struct ravb_hw_info, to enable this
feature specifically for R-Car Gen3 now and later extend it to RZ/G2L.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car Gen3 supports TX and RX clock internal delay modes, whereas R-Car
Gen2 and RZ/G2L do not support it.
Add an internal_delay hw feature bit to struct ravb_hw_info to enable this
only for R-Car Gen3.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On R-Car the checksum calculation on RX frames is done by the E-MAC
module, whereas on RZ/G2L it is done by the TOE.
TOE calculates the checksum of received frames from E-MAC and outputs it to
DMAC. TOE also calculates the checksum of transmission frames from DMAC and
outputs it E-MAC.
Add net_features and net_hw_features to struct ravb_hw_info, to support
subsequent SoCs without any code changes in the ravb_probe function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The device stats strings for R-Car and RZ/G2L are different.
R-Car provides 30 device stats, whereas RZ/G2L provides only 15. In
addition, RZ/G2L has stats "rx_queue_0_csum_offload_errors" instead of
"rx_queue_0_missed_errors".
Add structure variables gstrings_stats and gstrings_size to struct
ravb_hw_info, so that subsequent SoCs can be added without any code
changes in the ravb_get_strings function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car provides 30 device stats, whereas RZ/G2L provides only 15. In
addition, RZ/G2L has stats "rx_queue_0_csum_offload_errors" instead of
"rx_queue_0_missed_errors".
Replace RAVB_STATS_LEN macro with a structure variable stats_len to
struct ravb_hw_info, to support subsequent SoCs without any code changes
to the ravb_get_sset_count function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The maximum descriptor size that can be specified on the reception side for
R-Car is 2048 bytes, whereas for RZ/G2L it is 8096.
Add the max_rx_len variable to struct ravb_hw_info for allocating different
RX skb buffer sizes for R-Car and RZ/G2L using the netdev_alloc_skb
function.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
R-Car Gen2 needs a 4byte aligned address for the transmission buffer,
whereas R-Car Gen3 doesn't have any such restriction.
Add aligned_tx to struct ravb_hw_info to select the driver to choose
between aligned and unaligned tx buffers.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DMAC and EMAC blocks of Gigabit Ethernet IP found on RZ/G2L SoC are
similar to the R-Car Ethernet AVB IP. With a few changes in the driver we
can support both IPs.
This patch adds the struct ravb_hw_info to hold hw features, driver data
and function pointers to support both the IPs. It also replaces the driver
data chip type with struct ravb_hw_info by moving chip type to it.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of TX descriptors per packet is an unsigned value and
the variable for holding this information should be unsigned.
This patch replaces the data type of num_tx_desc variable in struct
ravb_private from 'int' to 'unsigned int'.
This patch also updates the data type of local variables to unsigned int,
where the local variables are evaluated using num_tx_desc.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 'imply' keyword does not do what most people think it does, it only
politely asks Kconfig to turn on another symbol, but does not prevent
it from being disabled manually or built as a loadable module when the
user is built-in. In the ICE driver, the latter now causes a link failure:
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_eth_ioctl':
ice_main.c:(.text+0x13b0): undefined reference to `ice_ptp_get_ts_config'
ice_main.c:(.text+0x13b0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_get_ts_config'
aarch64-linux-ld: ice_main.c:(.text+0x13bc): undefined reference to `ice_ptp_set_ts_config'
ice_main.c:(.text+0x13bc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_set_ts_config'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_prepare_for_reset':
ice_main.c:(.text+0x31fc): undefined reference to `ice_ptp_release'
ice_main.c:(.text+0x31fc): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `ice_ptp_release'
aarch64-linux-ld: drivers/net/ethernet/intel/ice/ice_main.o: in function `ice_rebuild':
This is a recurring problem in many drivers, and we have discussed
it several times befores, without reaching a consensus. I'm providing
a link to the previous email thread for reference, which discusses
some related problems.
To solve the dependency issue better than the 'imply' keyword, introduce a
separate Kconfig symbol "CONFIG_PTP_1588_CLOCK_OPTIONAL" that any driver
can depend on if it is able to use PTP support when available, but works
fine without it. Whenever CONFIG_PTP_1588_CLOCK=m, those drivers are
then prevented from being built-in, the same way as with a 'depends on
PTP_1588_CLOCK || !PTP_1588_CLOCK' dependency that does the same trick,
but that can be rather confusing when you first see it.
Since this should cover the dependencies correctly, the IS_REACHABLE()
hack in the header is no longer needed now, and can be turned back
into a normal IS_ENABLED() check. Any driver that gets the dependency
wrong will now cause a link time failure rather than being unable to use
PTP support when that is in a loadable module.
However, the two recently added ptp_get_vclocks_index() and
ptp_convert_timestamp() interfaces are only called from builtin code with
ethtool and socket timestamps, so keep the current behavior by stubbing
those out completely when PTP is in a loadable module. This should be
addressed properly in a follow-up.
As Richard suggested, we may want to actually turn PTP support into a
'bool' option later on, preventing it from being a loadable module
altogether, which would be one way to solve the problem with the ethtool
interface.
Fixes: 06c16d89d2 ("ice: register 1588 PTP clock device object for E810 devices")
Link: https://lore.kernel.org/netdev/20210804121318.337276-1-arnd@kernel.org/
Link: https://lore.kernel.org/netdev/CAK8P3a06enZOf=XyZ+zcAwBczv41UuCTz+=0FMf2gBz1_cOnZQ@mail.gmail.com/
Link: https://lore.kernel.org/netdev/CAK8P3a3=eOxE-K25754+fB_-i_0BZzf9a9RfPTX3ppSwu9WZXw@mail.gmail.com/
Link: https://lore.kernel.org/netdev/20210726084540.3282344-1-arnd@kernel.org/
Acked-by: Shannon Nelson <snelson@pensando.io>
Acked-by: Jacob Keller <jacob.e.keller@intel.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20210812183509.1362782-1-arnd@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The EtherAVB instances on the R-Car E3/D3 and RZ/G2E SoCs do not support
TX clock internal delay modes, and the EtherAVB driver prints a warning
if an unsupported "rgmii-*id" PHY mode is specified, to catch buggy
DTBs.
Commit a6f51f2efa ("ravb: Add support for explicit internal
clock delay configuration") deprecated deriving the internal delay mode
from the PHY mode, in favor of explicit configuration using the now
mandatory "rx-internal-delay-ps" and "tx-internal-delay-ps" properties,
thus delegating the warning to the legacy fallback code.
Since explicit configuration of a (valid) internal clock delay
configuration is enforced by validating device tree source files against
DT binding files, and all upstream DTS files have been converted as of
commit a5200e63af ("arm64: dts: renesas: rzg2: Convert EtherAVB to
explicit delay handling"), the checks in the legacy fallback code can be
removed.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/2037542ac56e99413b9807e24049711553cc88a9.1628696778.git.geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Most users of ndo_do_ioctl are ethernet drivers that implement
the MII commands SIOCGMIIPHY/SIOCGMIIREG/SIOCSMIIREG, or hardware
timestamping with SIOCSHWTSTAMP/SIOCGHWTSTAMP.
Separate these from the few drivers that use ndo_do_ioctl to
implement SIOCBOND, SIOCBR and SIOCWANDEV commands.
This is a purely cosmetic change intended to help readers find
their way through the implementation.
Cc: Doug Ledford <dledford@redhat.com>
Cc: Jason Gunthorpe <jgg@ziepe.ca>
Cc: Jay Vosburgh <j.vosburgh@gmail.com>
Cc: Veaceslav Falico <vfalico@gmail.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Vivien Didelot <vivien.didelot@gmail.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Vladimir Oltean <olteanv@gmail.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Jason Gunthorpe <jgg@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the member description comments for struct ravb_desc by
removing the extra TAB.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix the typo RX->TX in comment, as the code following the comment
process TX and not RX.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In preparation for FORTIFY_SOURCE performing compile-time and run-time
field bounds checking for memcpy(), memmove(), and memset(), avoid
intentionally reading across neighboring array fields.
The memcpy() is copying the entire structure, not just the first array.
Adjust the source argument so the compiler can do appropriate bounds
checking.
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_platform_get_and_ioremap_resource() to simplify
code.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The call to clk_disable_unprepare() can happen before priv is
initialized. This means moving clk_disable_unprepare out of
out_release into a new label.
Fixes: 8ef7adc6be ("net: ethernet: ravb: Enable optional refclk")
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a lot of frames were received in the short term, the driver
caused a stuck of receiving until a new frame was received. For example,
the following command from other device could cause this issue.
$ sudo ping -f -l 1000 -c 1000 <this driver's ipaddress>
The previous code always cleared the interrupt flag of RX but checks
the interrupt flags in ravb_poll(). So, ravb_poll() could not call
ravb_rx() in the next time until a new RX frame was received if
ravb_rx() returned true. To fix the issue, always calls ravb_rx()
regardless the interrupt flags condition.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
of_get_mac_address() returns a "const void*" pointer to a MAC address.
Lately, support to fetch the MAC address by an NVMEM provider was added.
But this will only work with platform devices. It will not work with
PCI devices (e.g. of an integrated root complex) and esp. not with DSA
ports.
There is an of_* variant of the nvmem binding which works without
devices. The returned data of a nvmem_cell_read() has to be freed after
use. On the other hand the return of_get_mac_address() points to some
static data without a lifetime. The trick for now, was to allocate a
device resource managed buffer which is then returned. This will only
work if we have an actual device.
Change it, so that the caller of of_get_mac_address() has to supply a
buffer where the MAC address is written to. Unfortunately, this will
touch all drivers which use the of_get_mac_address().
Usually the code looks like:
const char *addr;
addr = of_get_mac_address(np);
if (!IS_ERR(addr))
ether_addr_copy(ndev->dev_addr, addr);
This can then be simply rewritten as:
of_get_mac_address(np, ndev->dev_addr);
Sometimes is_valid_ether_addr() is used to test the MAC address.
of_get_mac_address() already makes sure, it just returns a valid MAC
address. Thus we can just test its return code. But we have to be
careful if there are still other sources for the MAC address before the
of_get_mac_address(). In this case we have to keep the
is_valid_ether_addr() call.
The following coccinelle patch was used to convert common cases to the
new style. Afterwards, I've manually gone over the drivers and fixed the
return code variable: either used a new one or if one was already
available use that. Mansour Moufid, thanks for that coccinelle patch!
<spml>
@a@
identifier x;
expression y, z;
@@
- x = of_get_mac_address(y);
+ x = of_get_mac_address(y, z);
<...
- ether_addr_copy(z, x);
...>
@@
identifier a.x;
@@
- if (<+... x ...+>) {}
@@
identifier a.x;
@@
if (<+... x ...+>) {
...
}
- else {}
@@
identifier a.x;
expression e;
@@
- if (<+... x ...+>@e)
- {}
- else
+ if (!(e))
{...}
@@
expression x, y, z;
@@
- x = of_get_mac_address(y, z);
+ of_get_mac_address(y, z);
... when != x
</spml>
All drivers, except drivers/net/ethernet/aeroflex/greth.c, were
compile-time tested.
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
For devices that use a programmable clock for the AVB reference clock,
the driver may need to enable them. Add code to find the optional clock
and enable it when available.
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Place the RX/TX descriptor bit *enum*s where they belong -- after the
corresponding RX/TX descriptor *struct*s and, while at it, switch to
declaring one *enum* entry per line...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finally, rename the rest of the *enum* tags still not (exactly) matching
the abbreviated register names from the manuals...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all the SoC manuals (except R-Car gen2) the PHY status register's name
is abbreviated to PSR with the only valid bit 0 named LMON. Follow the
suit and rename the corresponding *enum* tag/entry.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
In all the SoC manuals the TRSCER register bits match the corresponding
EESR registers's bits, but only on the R-Car gen2 SoC those are named
RINT<n> and TINT<n>. Follow the suit and rename the *enum* tag/entries
from DESC_I_* to TRSCER_*.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the RZ/A2M Group User's Manual: Hardware, Rev. 2.00,
the TRSCER register has bit 9 reserved, hence we can't use the driver's
default TRSCER mask. Add the explicit initializer for sh_eth_cpu_data::
trscer_err_mask for R7S9210.
Fixes: 6e0bb04d0e ("sh_eth: Add R7S9210 support")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the RZ/A1H Group, RZ/A1M Group User's Manual: Hardware,
Rev. 4.00, the TRSCER register has bit 9 reserved, hence we can't use
the driver's default TRSCER mask. Add the explicit initializer for
sh_eth_cpu_data::trscer_err_mask for R7S72100.
Fixes: db893473d3 ("sh_eth: Add support for r7s72100")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
According to the SH7710, SH7712, SH7713 Group User's Manual: Hardware,
Rev. 3.00, the TRSCER register actually has only bit 7 valid (and named
differently), with all the other bits reserved. Apparently, this was not
the case with some early revisions of the manual as we have the other
bits declared (and set) in the original driver. Follow the suit and add
the explicit sh_eth_cpu_data::trscer_err_mask initializer for SH771x...
Fixes: 86a74ff21a ("net: sh_eth: add support for Renesas SuperH Ethernet")
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e73 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
sh_eth_close() does a synchronous power down of the device before
marking it closed. Revert the order, to make sure the device is never
marked opened while suspended.
While at it, use pm_runtime_put() instead of pm_runtime_put_sync(), as
there is no reason to do a synchronous power down.
Fixes: 7fa2955ff7 ("sh_eth: Fix sleeping function called from invalid context")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Link: https://lore.kernel.org/r/20210118150812.796791-1-geert+renesas@glider.be
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Wolfram reports that his R-Car H2-based Lager board can no longer be
rebooted in v5.11-rc1, as it crashes with an imprecise external abort.
The issue can be reproduced on other boards (e.g. Koelsch with R-Car
M2-W) too, if CONFIG_IP_PNP is disabled, and the Ethernet interface is
down at reboot time:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=422b6835, *pte=00000000, *ppte=00000000
Internal error: : 1406 [#1] ARM
Modules linked in:
CPU: 0 PID: 1105 Comm: init Tainted: G W 5.10.0-rc1-00402-ge2f016cf7751 #1048
Hardware name: Generic R-Car Gen2 (Flattened Device Tree)
PC is at sh_mdio_ctrl+0x44/0x60
LR is at sh_mmd_ctrl+0x20/0x24
...
Backtrace:
[<c0451f30>] (sh_mdio_ctrl) from [<c0451fd4>] (sh_mmd_ctrl+0x20/0x24)
r7:0000001f r6:00000020 r5:00000002 r4:c22a1dc4
[<c0451fb4>] (sh_mmd_ctrl) from [<c044fc18>] (mdiobb_cmd+0x38/0xa8)
[<c044fbe0>] (mdiobb_cmd) from [<c044feb8>] (mdiobb_read+0x58/0xdc)
r9:c229f844 r8:c0c329dc r7:c221e000 r6:00000001 r5:c22a1dc4 r4:00000001
[<c044fe60>] (mdiobb_read) from [<c044c854>] (__mdiobus_read+0x74/0xe0)
r7:0000001f r6:00000001 r5:c221e000 r4:c221e000
[<c044c7e0>] (__mdiobus_read) from [<c044c9d8>] (mdiobus_read+0x40/0x54)
r7:0000001f r6:00000001 r5:c221e000 r4:c221e458
[<c044c998>] (mdiobus_read) from [<c044d678>] (phy_read+0x1c/0x20)
r7:ffffe000 r6:c221e470 r5:00000200 r4:c229f800
[<c044d65c>] (phy_read) from [<c044d94c>] (kszphy_config_intr+0x44/0x80)
[<c044d908>] (kszphy_config_intr) from [<c044694c>] (phy_disable_interrupts+0x44/0x50)
r5:c229f800 r4:c229f800
[<c0446908>] (phy_disable_interrupts) from [<c0449370>] (phy_shutdown+0x18/0x1c)
r5:c229f800 r4:c229f804
[<c0449358>] (phy_shutdown) from [<c040066c>] (device_shutdown+0x168/0x1f8)
[<c0400504>] (device_shutdown) from [<c013de44>] (kernel_restart_prepare+0x3c/0x48)
r9:c22d2000 r8:c0100264 r7:c0b0d034 r6:00000000 r5:4321fedc r4:00000000
[<c013de08>] (kernel_restart_prepare) from [<c013dee0>] (kernel_restart+0x1c/0x60)
[<c013dec4>] (kernel_restart) from [<c013e1d8>] (__do_sys_reboot+0x168/0x208)
r5:4321fedc r4:01234567
[<c013e070>] (__do_sys_reboot) from [<c013e2e8>] (sys_reboot+0x18/0x1c)
r7:00000058 r6:00000000 r5:00000000 r4:00000000
[<c013e2d0>] (sys_reboot) from [<c0100060>] (ret_fast_syscall+0x0/0x54)
As of commit e2f016cf77 ("net: phy: add a shutdown procedure"),
system reboot calls phy_disable_interrupts() during shutdown. As this
happens unconditionally, the PHY registers may be accessed while the
device is suspended, causing undefined behavior, which may crash the
system.
Fix this by wrapping the PHY bitbang accessors in the sh_eth driver by
wrappers that take care of Runtime PM, to resume the device when needed.
Reported-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
The "undocumented" annotations in the EtherAVB driver were done against
the R-Car gen2 manuals; most of these registers/bits were then described
in the R-Car gen3 manuals -- reflect this fact in the annotations (note
that ECSIPR.LCHNGIP was documented in the recent R-Car gen2 manual)...
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
According to the R-Car Series, 3rd Generation User's Manual: Hardware,
Rev. 1.50, there's no APSR.DM field, instead there are 2 independent
RX/TX clock internal delay bits. Follow the suit: remove #define APSR_DM
and rename #define's APSR_DM_{R|T}DM to APSR_{R|T}DM.
While at it, do several more things to the declaration of *enum* APSR_BIT:
- remove superfluous indentation;
- annotate APSR_MEMS as undocumented;
- annotate APSR as R-Car Gen3 only.
Signed-off-by: Sergey Shtylyov <s.shtylyov@omprussia.ru>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
In the function ravb_hwtstamp_get() in ravb_main.c with the existing
values for RAVB_RXTSTAMP_TYPE_V2_L2_EVENT (0x2) and RAVB_RXTSTAMP_TYPE_ALL
(0x6)
if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_V2_L2_EVENT)
config.rx_filter = HWTSTAMP_FILTER_PTP_V2_L2_EVENT;
else if (priv->tstamp_rx_ctrl & RAVB_RXTSTAMP_TYPE_ALL)
config.rx_filter = HWTSTAMP_FILTER_ALL;
if the test on RAVB_RXTSTAMP_TYPE_ALL should be true,
it will never be reached.
This issue can be verified with 'hwtstamp_config' testing program
(tools/testing/selftests/net/hwtstamp_config.c). Setting filter type
to ALL and subsequent retrieving it gives incorrect value:
$ hwtstamp_config eth0 OFF ALL
flags = 0
tx_type = OFF
rx_filter = ALL
$ hwtstamp_config eth0
flags = 0
tx_type = OFF
rx_filter = PTP_V2_L2_EVENT
Correct this by converting if-else's to switch.
Fixes: c156633f13 ("Renesas Ethernet AVB driver proper")
Reported-by: Julia Lawall <julia.lawall@inria.fr>
Signed-off-by: Andrew Gabbasov <andrew_gabbasov@mentor.com>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@gmail.com>
Link: https://lore.kernel.org/r/20201026102130.29368-1-andrew_gabbasov@mentor.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Yoshihiro Shimoda