This pin needs to be configured in pull-down, non-tristate mode in order
for the backlight to work correctly.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Other boards use PULL_NONE for their debug UART pins, and without this
change, the board doesn't accept any serial input.
Don't set the I2S port pins to tristate mode, or no audio signal will
be sent out.
Fixes: 605ae5804385 ("ARM: tegra: add default pinctrl nodes for Venice2")
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Add the default pinmux configuration for the Tegra124 based
Venice2 platform.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Set the parent of the regulators LDO2 to LDO9 according to the
schematic. Set the base voltage to 3.3V, there is only 3.3V on the
module itself.
Set the Core and CPU voltage to the specified voltages of 1.2V and
1.0V respectivly.
LDO6 should deliver 2.85V. The attached peripherals were not in
use so far.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use Tegra pinconrol dt-binding macro to set the values of different pinmux
properties of Tegra30 platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use Tegra pinconrol dt-binding macro to set the values of different pinmux
properties of Tegra20 platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use Tegra pinconrol dt-binding macro to set the values of different pinmux
properties of Tegra114 platforms.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Use key code macros for all key code refernced for keys.
For tegra20-seaboard.dts and tegra20-harmony.dts:
The key comment for key (16th row and 1st column) is KEY_KPSLASH but
code is 0x004e which is the key code for KEY_KPPLUS. As there other
key exist with KY_KPPLUS, I am assuming key code is wrong and comment
is fine. With this assumption, I am keeping the key code as KEY_KPSLASH.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Subsequent patches will need to reference a PWM channel for backlight
support, so enable the PWM device and assign a label to it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Stephen Warren <swarren@nvidia.com>
The PWM controller on Tegra124 is the same as the one on earlier SoC
generations.
Signed-off-by: Thierry Reding <treding@nvidia.com>
[swarren, added reset properties]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Venice2 uses the MAX98090 audio CODEC, and supports built-in speakers,
and a combo headphones/microphone jack. Add a top-level sound card node
to represent this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 contains a similar set of audio devices to previous Tegra chips.
Specifically, there is an AHUB device which contains DMA FIFOs and audio
routing, and which hosts various audio-related components such as I2S
controllers.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Enable all the I2C controllers that are wired up on Venice2. I don't
know the correct I2C bus clock rates, so set them all to a conservative
100KHz for now.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 has 6 I2C controllers. The first 5 have identical configuration
to Tegra114, but the sixth obviously has different interrupt/... IDs.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Tegra124 has 4 MMC controllers just like previous versions of the SoC.
Note that there are some non-backwards-compatible HW differences, and
hence a new DT compatible value must be used to describe the HW.
Also enable the relevant controllers in the Venice2 board DT.
power-gpios property suggested by Thierry Reding.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
Instantiate the APB DMA controller in the Tegra124 DT, and add all
DMA-related properties to other DT nodes that rely on (reference) the
DMA controller's node.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
The DT bindings now require module resets to be specified. The earlier
patches which added these nodes were originally written before that
requirement.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch adds clock properties for devices in the DT for basic support
of Tegra124 SoC.
Signed-off-by: Joseph Lo <josephl@nvidia.com>
[swarren, added missing unit address to "clock" node]
Signed-off-by: Stephen Warren <swarren@nvidia.com>
For Tegra DT files, I've been attempting to keep the nodes sorted in
the order:
1) Nodes with reg, in order of reg.
2) Nodes without reg, alphabetically.
This patch fixes a few escapees that I missed:-(
The diffs look larger than they really are, because sometimes when one
node was moved up or down, diff chose to represent this as many other
nodes being moved the other way!
Signed-off-by: Stephen Warren <swarren@nvidia.com>
DT node names should include a unit address iff the node has a reg
property. For Tegra DTs at least, we were previously applying a different
rule, namely that node names only needed to include a unit address if it
was required to make the node name unique. Consequently, many unit
addresses are missing. Add them.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Now that all Tegra drivers have been converted to use DMA APIs which
retrieve DMA channel information from standard DMA DT properties, we can
remove all the legacy DT DMA-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Now that all Tegra drivers have been converted to use the common reset
framework, we can remove all the legacy DT clocks/clock-names entries for
"clocks" that were only used with the old custom Tegra module reset API.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
This patch switches the Tegra DT files to use the standard DMA DT bindings
rather than custom properties. Note that the legacy properties are not yet
removed; the drivers must be updated to use the new properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
An earlier patch updated the Tegra DT bindings to require resets and
reset-names properties to be filled in. This patch updates the DT files
to include those properties.
Note that any legacy clocks and clock-names entries that are replaced by
reset properties are not yet removed; the drivers must be updated to use
the new resets and reset-names properties first.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Many of the Tegra DT binding documents say nothing about the clocks or
clock-names properties, yet those are present and required in DT files.
This patch simply updates the documentation file to match the implicit
definition of the binding, based on real-world DT content.
All Tegra bindings that mention clocks are updated to have consistent
wording and formatting of the clock-related properties.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-By: Terje Bergstrom <tbergstrom@nvidia.com>
Some of the clocks that were designated gate-clk do not have a gate, so
change those clocks to be of periph-clk type.
Signed-off-by: Dinh Nguyen <dinguyen@altera.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Tony Lindgren:
Few more legacy booting vs device tree booting fixes that people
have noticed while booting things with device tree for things like
omap4 WLAN, smsc911x, and beagle audio. Hopefully this will be it
for the legacy booting vs device tree fixes for this -rc cycle.
* tag 'omap-for-v3.13/more-dt-regressions' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: Fix the name of supplies for smsc911x shared by OMAP
ARM: OMAP2+: Powerdomain: Fix unchecked dereference of arch_pwrdm
ARM: dts: omap3-beagle: Add omap-twl4030 audio support
ARM: dts: omap4-sdp: Fix pin muxing for wl12xx
ARM: dts: omap4-panda-common: Fix pin muxing for wl12xx
From Nicolas Ferre:
AT91: second round of fixes for 3.13
- reduce IP frequency for I2C on sama5d3
- missing aliases directive for USART3 on 9x5 family
- a PM symbol is missing if !CONFIG_PM
* tag 'at91-fixes' of git://github.com/at91linux/linux-at91:
ARM: at91: fixed unresolved symbol "at91_pm_set_standby" when built without CONFIG_PM
ARM: at91: add usart3 alias to dtsi
ARM: at91: sama5d3: reduce TWI internal clock frequency
From Jason Cooper, mvebu DT fixes for v3.13:
- mvebu
- PCIe fixes now that we have test devices with more ports.
- fix access to coherency registers
* tag 'mvebu-dt-fixes-3.13' of git://git.infradead.org/linux-mvebu:
ARM: mvebu: re-enable PCIe on Armada 370 DB
ARM: mvebu: use the virtual CPU registers to access coherency registers
ARM: mvebu: fix second and third PCIe unit of Armada XP mv78260
ARM: mvebu: second PCIe unit of Armada XP mv78230 is only x1 capable
From Tony Lindgren:
Some omap related fixes that have come up with people moving to device
tree only based booting for omap2+.
The series contains a handful of fixes for the igep boards as they were
one of the first omap3 boards to jump over completely to device tree
based booting. So these can be considered regressions compared to
booting igep in legacy mode with board files in v3.12.
Also included are few other device tree vs legacy booting regressions:
- yet more missing omap3 .dtsi entries that have showed up booting
various boards with device tree only
- n900 eMMC device tree fix
- fixes for beagle USB EHCI
- two fixes to make omap2420 MMC work
As we're moving omap2+ to be device tree only for v3.14, I'd like to
have v3.13 work equally well for legacy based booting and device tree
based booting. So there will be likely few more device tree related
booting patches trickling in.
This series also includes a regression fix for the omap timer posted
mode that may wrongly stay on from the bootloader for some SoCs.
* tag 'omap-for-v3.13/fixes-against-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
mmc: omap: Fix I2C dependency and make driver usable with device tree
mmc: omap: Fix DMA configuration to not rely on device id
ARM: dts: omap3-beagle: Fix USB host on beagle boards (for 3.13)
ARM: dts: omap3-igep0020: name twl4030 VPLL2 regulator as vdds_dsi
ARM: dts: AM33XX IGEP0033: add USB support
ARM: dts: AM33XX BASE0033: add 32KBit EEPROM support
ARM: dts: AM33XX BASE0033: add pinmux and user led support
ARM: dts: AM33XX BASE0033: add pinmux and hdmi node to enable display
ARM: dts: omap3-igep0020: Add pinmuxing for DVI output
ARM: dts: omap3-igep0020: Add pinmux setup for i2c devices
ARM: dts: omap3-igep: Update to use the TI AM/DM37x processor
ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO
ARM: dts: omap3-igep: Fix bus-width for mmc1
ARM: OMAP2+: dss-common: change IGEP's DVI DDC i2c bus
ARM: OMAP2+: Disable POSTED mode for errata i103 and i767
ARM: OMAP2+: Fix eMMC on n900 with device tree
ARM: OMAP2+: Add fixed regulator to omap2plus_defconfig
ARM: OMAP2+: Fix more missing data for omap3.dtsi file
Signed-off-by: Olof Johansson <olof@lixom.net>
drivers/net/ethernet/smsc/smsc911x.c is expecting supplies named
"vdd33a" and "vddvario". Currently the shared DTS file provides
"vmmc" and "vmmc_aux", and the supply lookup will fail:
smsc911x 2c000000.ethernet: Looking up vdd33a-supply from device tree
smsc911x 2c000000.ethernet: Looking up vdd33a-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
smsc911x 2c000000.ethernet: Looking up vddvario-supply from device tree
smsc911x 2c000000.ethernet: Looking up vddvario-supply property in node /ocp/gpmc@6e000000/ethernet@gpmc failed
Fix it!
Looks like commmit 6b2978ac40 (ARM: dts: Shared file for omap GPMC
connected smsc911x) made the problem more visible by moving the smc911x
configuration from the omap3-igep0020.dts file to the generic file.
But it seems we've had this problem since commit d72b441501
(ARM: dts: omap3-igep0020: Add SMSC911x LAN chip support).
Tested on OMAP3 Overo platform.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[tony@atomide.com: updated comments for the commits causing the problem]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This adds typical McBSP2-TWL4030 audio description to the legacy
Beagle Board.
Signed-off-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Mux mode for wlan/sdmmc5 should be MODE0 in pinmux_wl12xx_pins and
Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes WLAN on omap4-sdp that got broken in v3.10 when we
moved omap4 to boot using device tree only as I did not have
the WL12XX card in my omap4 SDP to test with. The commit that
attempted to make WL12XX working on omap4 SDP was 775d2418f3
(ARM: dts: Fix muxing and regulator for wl12xx on the SDIO
bus for blaze).
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: updated comments for the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
pin mux wl12xx_gpio and wl12xx_pins should be part of omap4_pmx_core
and not omap4_pmx_wkup. So, move wl12xx_* to omap4_pmx_core.
Fix the following error message:
pinctrl-single 4a31e040.pinmux: mux offset out of range: 0x38 (0x38)
pinctrl-single 4a31e040.pinmux: could not add functions for pinmux_wl12xx_pins 56x
SDIO card is not detected after moving pin mux to omap4_pmx_core since
sdmmc5_clk pull is disabled. Enable Pull up on sdmmc5_clk to detect SDIO card.
This fixes a regression where WLAN did not work after a warm reset
or after one up/down cycle that happened when we move omap4 to boot
using device tree only. For reference, the kernel bug is described at:
https://bugzilla.kernel.org/show_bug.cgi?id=63821
Cc: stable@vger.kernel.org # v3.10+
Signed-off-by: Balaji T K <balajitk@ti.com>
[tony@atomide.com: update comments to describe the regression]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Alias was missing for SoC of the at91sam9x5 familly that embed USART3.
Reported-by: Jiri Prchal <jiri.prchal@aksignal.cz>
[b.brezillon@overkiz.com: advised to place changes in at91sam9x5_usart3.dtsi]
Acked-by: Boris BREZILLON <b.brezillon@overkiz.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Beagle (rev. C4) and Beagle-XM (all revs) need VAUX2 1.8V supply
for the USB PHY.
As the generic PHY driver can't handle more than one supply
at the moment, we configure this supply to be always on.
This will cause a very small power impact if the USB host subsystem
is not in use, about 76.86 micro-W + LDO power.
Older Beagle boards (prior to C4) don't have VAUX2 connected anywhere,
so there won't be any functional impact on those boards other than
some additional LDO power consumption.
Reported-by: Nishanth Menon <nm@ti.com>
Tested-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On Device Tree boot the VDDS_DSI regulator is not linked to
the DPI device so omapfb driver probing fails with:
[ 3.186035] OMAPFB: omapfb_probe
[ 3.190704] omapdss DPI error: can't get VDDS_DSI regulator
[ 3.196594] omapfb omapfb: failed to connect default display
[ 3.202667] omapfb omapfb: failed to init overlay connections
[ 3.208892] OMAPFB: free_resources
[ 3.212493] OMAPFB: free all fbmem
[ 3.216735] omapfb omapfb: failed to setup omapfb
As a workaround name the VPLL2 regulator from twl4030 as vdds_dsi
so getting the VDDS_DSI regulator will succeed on dpi_init_regulator().
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add node to support the USB Host and the USB OTG on the IGEP AQUILA
Processor Board.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEP AQUILA EXPANSION has a 32KBit EEPROM for user data storage.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the user leds on the IGEP AQUILA EXPANSION. The has two leds,
one green and one red, that are controllable by software.
Signed-off-by: Enric Balletbo i Serra <eballetbo@iseebcn.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Enable the hdmi output and the LCD Controller on IGEP AQUILA. Also
configure the correct pinmux for output of video data from the SoC
to the HDMI encoder.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The IGEPv2 has a TFP410 DPI-to-DVI encoder attached to OMAP's
Display SubSystem (DSS).
Add mux setup for DSS pins and also for the GPIO 170 pin that
is used to ensure that the DVI-D is powered down on power up.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add pin muxing support for IGEP boards i2c controllers.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most of the boards are using the TI AM/DM37x processor, there is only a small
quantity of IGEP Processor Boards based on TI OMAP3530. So it's better use the
omap36xx.dtsi include instead of omap34xx.dtsi include. We can add support
for the 34xx based variant later on as needed.
To avoid confusion we have added to the model the (TI AM/DM37x) comment.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
[tony@atomide.com: updated comments for the 34xx to 36xx include change]
Signed-off-by: Tony Lindgren <tony@atomide.com>
The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In
both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using
the same MMC interface and uses the same GPIOs.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Both, IGEPv2 and IGEP COM MODULE have a bus-width of 4 not 8, so fix this and
do not mux data pins from mmc1_data4 to mmc1_data7.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The I2C controller node needs #address-cells and #size-cells properties,
but these are currently missing. Add them. This allows child nodes to be
parsed correctly.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Without the interrupt you'll get problems if you enable
CONFIG_RTC_DRV_MAX77686. Setup the interrupt properly in the device
tree.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org
Thierry Reding