The drm_panel_enable/disable and drm_panel_prepare/unprepare calls are
not fine grained enough to abstract all the different steps we need to
take (and VBT sequences we need to exec) properly. So simply remove the
panel _enable/disable and prepare/unprepare callbacks and instead
export intel_dsi_exec_vbt_sequence() from intel_dsi_panel_vbt.c
and call that from intel_dsi_enable/disable().
No functional changes.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/b4ca5185d4788d92df2ed60837a24b8962a8e8ba.1488273823.git.jani.nikula@intel.com
Instead of calling wait_for_dsi_fifo_empty on all dsi ports after calling
a drm_panel_foo helper which calls VBT sequences, move it to the VBT
mipi_exec_send_packet helper, which is the one VBT instruction which
actually puts data in the fifo.
This results in a nice cleanup making it clearer what all the steps on
intel_dsi_enable / disable are and this also makes the VBT code properly
wait till a command has actually been send before executing the next
steps (typically a delay) in the VBT sequence.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Bob Paauwe <bob.j.paauwe@intel.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/289977b5699e252fea5c211d1d1645f9e79cca79.1488273823.git.jani.nikula@intel.com
For GEMINILAKE, dphy param reg values are programmed in terms
of HS byte clock count while for older platforms in terms of
HS ddr clk count.
v2: Added comments to clarify ddr clock count calculation
v3: Use multiplier variable instead of IS_GEMINILAKE()
check everywhere (Jani)
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Madhav Chauhan <madhav.chauhan@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487335415-14766-2-git-send-email-madhav.chauhan@intel.com
Dump out more of the DSI configuration details during init.
This includes pclk, burst_mode_ratio, lane_count, pixel_overlap,
video_mode_format and reset_timer_val.
v2: Dump more info (Chris)
v3: Use the VIDEO_MODE_ defines for consistency (Chris)
Dump dphy_reg too (Chris)
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/20161221143114.23530-1-ville.syrjala@linux.intel.com
Request the GPIO by index through the consumer API. For now, use a quick
hack to store the already requested ones, simply because I have no idea
whether this actually works or not, and I have no way to test it.
v2 by Mika: switch *NULL* to *"panel"* when requesting gpio for MIPI/DSI
panel.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Mika Kahola <mika.kahola@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1480923034-21916-1-git-send-email-mika.kahola@intel.com
Set the CHV_GPIO_GPIOEN bit when updating GPIOs from chv_exec_gpio.
Fixes: a0a6d4ffd2 ("drm/i915/dsi: add support for gpio elements on CHV")
Cc: stable@vger.kernel.org
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161201202925.12220-3-hdegoede@redhat.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Looking at the ADF code from the Android kernel sources for a
cherrytrail tablet I noticed that it is calling the
MIPI_SEQ_ASSERT_RESET sequence from the panel prepare hook.
Until commit b1cb1bd291 ("drm/i915/dsi: update reset and power sequences
in panel prepare/unprepare hooks") the mainline i915 code was doing the
same. That commits effectively swaps the calling of MIPI_SEQ_ASSERT_RESET /
MIPI_SEQ_DEASSERT_RESET.
Looking at the naming of the sequences that is the right thing to do,
but the problem is, that the old mainline code and the ADF code was
actually calling the right sequence (tested on a cube iwork8 air tablet),
and the swapping of the calling breaks things.
This breakage was likely not noticed in testing because on cherrytrail,
currently chv_exec_gpio ends up disabling the gpio pins rather then
setting them (this is fixed in the next patch in this patch-set).
This commit fixes the swapping by fixing MIPI_SEQ_ASSERT/DEASSERT_RESET's
places in the enum defining them, so that their (new) names match their
actual use.
Changes in v2:
-Add a comment to the enum explaining that the assert/reassert names
are swapped in the spec
Fixes: b1cb1bd291 ("drm/i915/dsi: update reset and power sequences...")
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/20161202150128.29871-1-hdegoede@redhat.com
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Based on the documentation alone, it's anyone's guess when exactly we
should be running these sequences. Add power on/off sequences where they
feel logical and update assert/deassert reset. The drm panel hooks don't
currently offer us more granularity anyway.
v2: update assert/deassert reset as well (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1543320494df953fa073e136248238eaa1eed059.1474286487.git.jani.nikula@intel.com
Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().
text data bss dec hex filename
1073824 4562 416 1078802 107612 drivers/gpu/drm/i915/i915.ko
1068976 4562 416 1073954 106322 drivers/gpu/drm/i915/i915.ko
Created by the coccinelle script:
@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Dave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk
Add support for CHV gpio programming in DSI gpio elements.
v2: Overhaul macros according to Ville's review.
v3: Address Ville's review:
- swap E and SE gpio ranges
- add a note about max SE index
- use GPO, not HIZ
- swap cfg0 and cfg1
v4: fix port for dsi sequence versions 1 and 2
[Rewritten by Jani, based on earlier work by Yogesh and Deepak.]
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/bdaaf9915a5005305b31bb26cf619a5a82472f2a.1461666263.git.jani.nikula@intel.com
Define and store the pad base offset in the array, and reference the
pconf0 and padval registers through macros. Add VLV prefixes to
macros. Use spec nomenclature for pconf0 and padval.
v2: Address Ville's review comments, squash another patch here.
v3: Use the names Ville dug up in the specs.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/34932140b78a3de7f825c78380a08c930694651b.1459884518.git.jani.nikula@intel.com
A small step moving us closer to DRM MIPI DSI code. Use enum
mipi_dsi_pixel_format instead of our own. The first benefit is being
able to use common mipi_dsi_pixel_format_to_bpp().
There's a little back and forth conversion with the VBT -> enum ->
register, since we have just shoved the VBT value into the register
directly. Longer term, all the VBT parsing and deciphering should be
done in intel_bios.c, and abstracted there.
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1458123700-16003-2-git-send-email-jani.nikula@intel.com
The bpp value which is used while calulating the txbyteclkhs values
should be wrt the pixel format value. Currently bpp is coming
from pipe config to calculate txbyteclkhs. Fix it in this patch.
V2: dsi_pixel_format_bpp is used to retrieve the bpp from pixel_format
[Review: Jani]
Signed-off-by: Deepak M <m.deepak@intel.com>
Signed-off-by: Yogesh Mohan Marimuthu <yogesh.mohan.marimuthu@intel.com>
Signed-off-by: Ramalingam C <ramalingam.c@intel.com>
Tested-by: Mika Kahola <mika.kahola@intel.com> # BYT
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1455203007-10850-1-git-send-email-ramalingam.c@intel.com
Make the gpio read/write functions more generic iosf sideband read/write
functions, taking the iosf port as argument.
v2: rebase
v3: rebase
v4 by Jani: address Ville's review
v5 by Jani: drop the PCI_DEVFN change (Ville)
Signed-off-by: Deepak M <m.deepak@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1454604915-17142-1-git-send-email-jani.nikula@intel.com
The sequence block has sizes of elements after the operation byte since
sequence block v3. Use it to skip elements we don't support yet.
v2: remove redundant exec_elem[operation_byte] check (Daniel)
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452006408-27688-1-git-send-email-jani.nikula@intel.com
The changes since the sequence block v2 are:
* The whole MIPI bios data block has a separate 32-bit size field since
v3, stored after the version. This facilitates big sequences.
* The size of the panel specific sequence blocks has grown to 32
bits. This facilitates big sequences.
* The elements within sequences now have an 8-bit size field following
the operation byte. This facilitates skipping unknown new operation
bytes, i.e. forward compatibility.
v2 (of the patch): use DRM_ERROR for unknown operation byte
v3 (of the patch): even more bounds checking (Ville)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1452518102-3154-1-git-send-email-jani.nikula@intel.com
Rename dpio_lock to sb_lock to inform the reader that its primary
purpose is to protect the sideband mailbox rather than some DPIO
state.
Signed-off-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The removed functions can be resurrected in intel_dsi.c as need arises.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Use the drm core interfaces in preparation of removing our homebrew.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Add basic support for using the drm mipi dsi framework for DSI. We don't
use device tree which is pretty much required by mipi_dsi_host_register
and friends, and we don't have the kind of device model the functions
expect either. So we cheat and use it as a library to abstract what we
need: a nice, clean interface for DSI transfers. This means we will have
to be careful with what functions we call, as the driver model devices
in mipi_dsi_host and mipi_dsi_device will *not* be initialized.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Replace intel_dsi_device and intel_dsi_dev_ops with drm_panel and
drm_panel_funcs. They are adequate for what we have now, and if we end
up needing more than this we should improve drm_panel. This will keep us
better aligned with the drm core infrastructure.
The panel driver initialization changes a bit. It still remains hideous,
but fixing that is beyond the scope here.
v2: extend mode config mutex to cover drm_panel_get_modes (Shobhit)
vbt_panel->intel_dsi = intel_dsi in vbt panel init (Shobhit)
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Const is good for you. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Remove all the trivial and/or dummy callbacks from intel dsi device
ops. Merge send_otp_cmds into panel_reset as they're called back to
back.
This will be helpful for switching to use drm_panel for the
callbacks. If we ever need the additional callbacks, we should add them
to drm_panel funcs.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-By: Shobhit Kumar <shobhit.kumar@intel.com>
[danvet: Resolve tiny conflict with ongoing atomic work.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
From now on for both DSI Ports A & C, the seq_port value has been
set to 0. seq_port value is parsed from Sequence block#53 of VBT.
So, for packets that needs to be read/write for DSI single link on
Port A and Port C will now be based on the DVO port from VBT block 2,
instead of seq_port.
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For dual link MIPI Panels, each port needs half of pixel clock. Pixel overlap
can be enabled if needed by panel, then in that case, pixel clock will be
increased for extra pixels.
v2 : Address review comments by Jani
- Removed the bit mask used for ->dual_link
- Used DSI instead of MIPI for #define variables
v3: Added the VLV_DISPLAY_BASE to VLV_CHICKEN_3 register
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
For Dual Link MIPI Panels, both Port A and Port C should be enabled
during the MIPI encoder enabling sequence. Similarly, during the
disabling sequence, both ports needs to be disabled.
v2: Used for_each_dsi_port macro instead of for loop
v3: Used intel_dsi->ports instead of dual_link var for dual link configuration check
v4: Masking of the required MIPI port bits before writing proper values
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch is in preparation of DSI dual link panels. For dual link
panels, few packets needs to be sent to Port A or Port C or both. Based
on the portno from MIPI Sequence Block#53, these sequences needs to be
sent accordingly.
v2: Addressed review comments by Jani
- port variables named properly
Signed-off-by: Gaurav K Singh <gaurav.k.singh@intel.com>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Hans de Goede