This work as a follow-up of commit f7b3bec6f5 ("net: allow setting ecn
via routing table") and adds RFC3168 section 6.1.1.1. fallback for outgoing
ECN connections. In other words, this work adds a retry with a non-ECN
setup SYN packet, as suggested from the RFC on the first timeout:
[...] A host that receives no reply to an ECN-setup SYN within the
normal SYN retransmission timeout interval MAY resend the SYN and
any subsequent SYN retransmissions with CWR and ECE cleared. [...]
Schematic client-side view when assuming the server is in tcp_ecn=2 mode,
that is, Linux default since 2009 via commit 255cac91c3 ("tcp: extend
ECN sysctl to allow server-side only ECN"):
1) Normal ECN-capable path:
SYN ECE CWR ----->
<----- SYN ACK ECE
ACK ----->
2) Path with broken middlebox, when client has fallback:
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
SYN ----->
<----- SYN ACK
ACK ----->
In case we would not have the fallback implemented, the middlebox drop
point would basically end up as:
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
SYN ECE CWR ----X crappy middlebox drops packet
(timeout, rtx)
In any case, it's rather a smaller percentage of sites where there would
occur such additional setup latency: it was found in end of 2014 that ~56%
of IPv4 and 65% of IPv6 servers of Alexa 1 million list would negotiate
ECN (aka tcp_ecn=2 default), 0.42% of these webservers will fail to connect
when trying to negotiate with ECN (tcp_ecn=1) due to timeouts, which the
fallback would mitigate with a slight latency trade-off. Recent related
paper on this topic:
Brian Trammell, Mirja Kühlewind, Damiano Boppart, Iain Learmonth,
Gorry Fairhurst, and Richard Scheffenegger:
"Enabling Internet-Wide Deployment of Explicit Congestion Notification."
Proc. PAM 2015, New York.
http://ecn.ethz.ch/ecn-pam15.pdf
Thus, when net.ipv4.tcp_ecn=1 is being set, the patch will perform RFC3168,
section 6.1.1.1. fallback on timeout. For users explicitly not wanting this
which can be in DC use case, we add a net.ipv4.tcp_ecn_fallback knob that
allows for disabling the fallback.
tp->ecn_flags are not being cleared in tcp_ecn_clear_syn() on output, but
rather we let tcp_ecn_rcv_synack() take that over on input path in case a
SYN ACK ECE was delayed. Thus a spurious SYN retransmission will not prevent
ECN being negotiated eventually in that case.
Reference: https://www.ietf.org/proceedings/92/slides/slides-92-iccrg-1.pdf
Reference: https://www.ietf.org/proceedings/89/slides/slides-89-tsvarea-1.pdf
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Mirja Kühlewind <mirja.kuehlewind@tik.ee.ethz.ch>
Signed-off-by: Brian Trammell <trammell@tik.ee.ethz.ch>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Dave That <dave.taht@gmail.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
OSA Ethernet hardware is introducing BRIDGEPORT functionality
similar (but not identical) to HiperSockets BRIDGEPORT. This
patch makes HiperSockets BRIDGEPORT related sysfs attributes
and udev events work with OSA hardware too.
Reviewed-by: Thomas Richter <tmricht@linux.vnet.ibm.com>
Signed-off-by: Eugene Crosser <Eugene.Crosser@ru.ibm.com>
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simplify the device tree support of the amd-xgbe driver by defining
the PHY-related resources within the ethernet device node. The support
provides backwards compatibility with the original way.
Update the driver version to 1.0.2.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AMD XGBE device is intended to work with a specific integrated PHY
and that PHY is not meant to be a standalone PHY for use by other
devices. As such this patch removes the phylib driver and implements
the PHY support in the amd-xgbe driver (the majority of the logic from
the phylib driver is moved into the amd-xgbe driver).
Update the driver version to 1.0.1.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device tree binding documentation for nxp,lpc1850-dwmac.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some Ethernet PHY devices/switches may not properly release the MDIO bus
during turn-around time, and fail to drive it low, which can be seen by
some controllers as a read failure, while the data clocked in is still
correct.
Add a boolean property "broken-turn-around" which is parsed by the
generic MDIO bus probing code and will set the corresponding bit in the
MDIO bus phy_ignore_ta_mask bitmask for MDIO bus drivers to utilize that
information.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems all we want here is to avoid endless 'goto reclassify' loop.
tc_classify_compat even resets this counter when something other
than TC_ACT_RECLASSIFY is returned, so this skb-counter doesn't
break hypothetical loops induced by something other than perpetual
TC_ACT_RECLASSIFY return values.
skb_act_clone is now identical to skb_clone, so just use that.
Tested with following (bogus) filter:
tc filter add dev eth0 parent ffff: \
protocol ip u32 match u32 0 0 police rate 10Kbit burst \
64000 mtu 1500 action reclassify
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Four minor merge conflicts:
1) qca_spi.c renamed the local variable used for the SPI device
from spi_device to spi, meanwhile the spi_set_drvdata() call
got moved further up in the probe function.
2) Two changes were both adding new members to codel params
structure, and thus we had overlapping changes to the
initializer function.
3) 'net' was making a fix to sk_release_kernel() which is
completely removed in 'net-next'.
4) In net_namespace.c, the rtnl_net_fill() call for GET operations
had the command value fixed, meanwhile 'net-next' adjusted the
argument signature a bit.
This also matches example merge resolutions posted by Stephen
Rothwell over the past two days.
Signed-off-by: David S. Miller <davem@davemloft.net>
There were a few review comments on the switchdev.txt documentation that
didn't get included with the Spring Cleanup series, so include them now.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Much need updated of switchdev documentation to cover what's been
implmented to-date. There are some XXX comments in the text for
unimplemented or broken items. I'd like to keep these in there (poor-man's
TODO list) and update the document once each issue is resolved.
Signed-off-by: Scott Feldman <sfeldma@gmail.com>
Acked-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The port key has three components - user-key, speed-part, and duplex-part.
The LSBit is for the duplex-part, next 5 bits are for the speed while the
remaining 10 bits are the user defined key bits. Get these 10 bits
from the user-space (through the SysFs interface) and use it to form the
admin port-key. Allowed range for the user-key is 0 - 1023 (10 bits). If
it is not provided then use zero for the user-key-bits (default).
It can set using following example code -
# modprobe bonding mode=4
# usr_port_key=$(( RANDOM & 0x3FF ))
# echo $usr_port_key > /sys/class/net/bond0/bonding/ad_user_port_key
# echo +eth1 > /sys/class/net/bond0/bonding/slaves
...
# ip link set bond0 up
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
[jt: * fixed up style issues reported by checkpatch
* fixed up context from change in ad_actor_sys_prio patch]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In an AD system, the communication between actor and partner is the
business between these two entities. In the current setup anyone on the
same L2 can "guess" the LACPDU contents and then possibly send the
spoofed LACPDUs and trick the partner causing connectivity issues for
the AD system. This patch allows to use a random mac-address obscuring
it's identity making it harder for someone in the L2 is do the same thing.
This patch allows user-space to choose the mac-address for the AD-system.
This mac-address can not be NULL or a Multicast. If the mac-address is set
from user-space; kernel will honor it and will not overwrite it. In the
absence (value from user space); the logic will default to using the
masters' mac as the mac-address for the AD-system.
It can be set using example code below -
# modprobe bonding mode=4
# sys_mac_addr=$(printf '%02x:%02x:%02x:%02x:%02x:%02x' \
$(( (RANDOM & 0xFE) | 0x02 )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )) \
$(( RANDOM & 0xFF )))
# echo $sys_mac_addr > /sys/class/net/bond0/bonding/ad_actor_system
# echo +eth1 > /sys/class/net/bond0/bonding/slaves
...
# ip link set bond0 up
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
[jt: fixed up style issues reported by checkpatch]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows user to randomize the system-priority in an ad-system.
The allowed range is 1 - 0xFFFF while default value is 0xFFFF. If user
does not specify this value, the system defaults to 0xFFFF, which is
what it was before this patch.
Following example code could set the value -
# modprobe bonding mode=4
# sys_prio=$(( 1 + RANDOM + RANDOM ))
# echo $sys_prio > /sys/class/net/bond0/bonding/ad_actor_sys_prio
# echo +eth1 > /sys/class/net/bond0/bonding/slaves
...
# ip link set bond0 up
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Reviewed-by: Nikolay Aleksandrov <nikolay@redhat.com>
[jt: * fixed up style issues reported by checkpatch
* changed how the default value is set in bond_check_params(), this
makes the default consistent between what gets set for a new bond
and what the default is claimed to be in the bonding options.]
Signed-off-by: Jonathan Toppins <jtoppins@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Introduce xmit_mode 'netif_receive' for pktgen which generates the
packets using familiar pktgen commands, but feeds them into
netif_receive_skb() instead of ndo_start_xmit().
Default mode is called 'start_xmit'.
It is designed to test netif_receive_skb and ingress qdisc
performace only. Make sure to understand how it works before
using it for other rx benchmarking.
Sample script 'pktgen.sh':
\#!/bin/bash
function pgset() {
local result
echo $1 > $PGDEV
result=`cat $PGDEV | fgrep "Result: OK:"`
if [ "$result" = "" ]; then
cat $PGDEV | fgrep Result:
fi
}
[ -z "$1" ] && echo "Usage: $0 DEV" && exit 1
ETH=$1
PGDEV=/proc/net/pktgen/kpktgend_0
pgset "rem_device_all"
pgset "add_device $ETH"
PGDEV=/proc/net/pktgen/$ETH
pgset "xmit_mode netif_receive"
pgset "pkt_size 60"
pgset "dst 198.18.0.1"
pgset "dst_mac 90:e2:ba:ff:ff:ff"
pgset "count 10000000"
pgset "burst 32"
PGDEV=/proc/net/pktgen/pgctrl
echo "Running... ctrl^C to stop"
pgset "start"
echo "Done"
cat /proc/net/pktgen/$ETH
Usage:
$ sudo ./pktgen.sh eth2
...
Result: OK: 232376(c232372+d3) usec, 10000000 (60byte,0frags)
43033682pps 20656Mb/sec (20656167360bps) errors: 10000000
Raw netif_receive_skb speed should be ~43 million packet
per second on 3.7Ghz x86 and 'perf report' should look like:
37.69% kpktgend_0 [kernel.vmlinux] [k] __netif_receive_skb_core
25.81% kpktgend_0 [kernel.vmlinux] [k] kfree_skb
7.22% kpktgend_0 [kernel.vmlinux] [k] ip_rcv
5.68% kpktgend_0 [pktgen] [k] pktgen_thread_worker
If fib_table_lookup is seen on top, it means skb was processed
by the stack. To benchmark netif_receive_skb only make sure
that 'dst_mac' of your pktgen script is different from
receiving device mac and it will be dropped by ip_rcv
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow flag NO_TIMESTAMP to turn timestamping on again, like other flags,
with a negation of the flag like !NO_TIMESTAMP.
Also document the option flag NO_TIMESTAMP.
Fixes: afb84b6261 ("pktgen: add flag NO_TIMESTAMP to disable timestamping")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-----BEGIN PGP SIGNATURE-----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=dcJu
-----END PGP SIGNATURE-----
Merge tag 'linux-can-next-for-4.2-20150506' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next
Marc Kleine-Budde says:
====================
pull-request: can-next 2015-05-06
this is a pull request of a seven patches for net-next/master.
Andreas Gröger contributes two patches for the janz-ican3 driver. In
the first patch, the documentation for already existing sysfs entries
is added, the second patch adds support for another module/firmware
variant. A patch by Shawn Landden makes the padding in the struct
can_frame explicit. The next 4 patches target the flexcan driver, the
first one is by David Jander adding some documentation, the reaming
three by me add more documentation and two small code cleanups.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
A few patches have come up since the merge window. The largest one is a
rewrite of the PXA lubbock/mainstone IRQ handling. This was already
broken in 2011 by a change to the GPIO code and only noticed now.
The other changes contained here are:
MAINTAINERS file updates:
- Ray Jui and Scott Branden are now co-maintainers for some of the
mach-bcm chips, while Christian Daudt and Marc Carino have stepped
down.
- Andrew Victor is no longer maintaining at91. Instead, Alexandre
Belloni now becomes an official maintainer, after having done a
bulk of the work for a while.
- Baruch Siach, who added the mach-digicolor platform in 4.1
is now listed as maintainer
- The git URL for mach-socfpga has changed
Bug fixes:
- Three bug fixes for new rockchip rk3288 code
- A regression fix to make SD card support work on certain ux500
boards
- multiple smaller dts fixes for imx, omap, mvebu, and shmobile
- a regression fiix for omap3 power consumption
- a fix for regression in the ARM CCI bus driver
Configuration changes:
- more imx platforms are now enabled in multi_v7_defconfig
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=lVQn
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A few patches have come up since the merge window. The largest one is
a rewrite of the PXA lubbock/mainstone IRQ handling. This was already
broken in 2011 by a change to the GPIO code and only noticed now.
The other changes contained here are:
MAINTAINERS file updates:
- Ray Jui and Scott Branden are now co-maintainers for some of the
mach-bcm chips, while Christian Daudt and Marc Carino have stepped
down.
- Andrew Victor is no longer maintaining at91. Instead, Alexandre
Belloni now becomes an official maintainer, after having done a
bulk of the work for a while.
- Baruch Siach, who added the mach-digicolor platform in 4.1 is now
listed as maintainer
- The git URL for mach-socfpga has changed
Bug fixes:
- Three bug fixes for new rockchip rk3288 code
- A regression fix to make SD card support work on certain ux500
boards
- multiple smaller dts fixes for imx, omap, mvebu, and shmobile
- a regression fiix for omap3 power consumption
- a fix for regression in the ARM CCI bus driver
Configuration changes:
- more imx platforms are now enabled in multi_v7_defconfig"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (39 commits)
MAINTAINERS: add Conexant Digicolor machines entry
MAINTAINERS: socfpga: update the git repo for SoCFPGA
ARM: multi_v7_defconfig: Select more FSL SoCs
MAINTAINERS: replace an AT91 maintainer
drivers: CCI: fix used_mask init in validate_group()
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
MAINTAINERS: Update brcmstb entry
MAINTAINERS: Remove Christian Daudt for mach-bcm
...
Add "cdns,zynqmp-gem" to be used for Zynq Ultrascale+ MPSoC.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Reviewed-by: Punnaiah Choudary Kalluri <punnaia@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Fix for a PCI resources management regression introduced during
the 4.0 cycle and related to the handling of ACPI resources'
Producer/Consumer flags that turn out to be useless (Jiang Liu).
- Fix for a MacBook regression related to the Smart Battery Subsystem
(SBS) driver causing various problems (stalls on boot, failure to
detect or report battery) to happen and introduced during the 3.18
cycle (Chris Bainbridge).
- Fix for an ACPI/PNP device enumeration regression introduced during
the 3.16 cycle caused by failing to include two PNP device IDs into
the list of IDs that PNP device objects need to be created for
(Witold Szczeponik).
- Fixes for two minor mistakes in the ACPI GPIO properties
documentation (Antonio Ospite, Rafael J Wysocki).
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)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=JFUn
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI fixes from Rafael Wysocki:
"These include three regression fixes (PCI resources management,
ACPI/PNP device enumeration, ACPI SBS on MacBook) and two ACPI
documentation fixes related to GPIO.
Specifics:
- Fix for a PCI resources management regression introduced during the
4.0 cycle and related to the handling of ACPI resources'
Producer/Consumer flags that turn out to be useless (Jiang Liu)
- Fix for a MacBook regression related to the Smart Battery Subsystem
(SBS) driver causing various problems (stalls on boot, failure to
detect or report battery) to happen and introduced during the 3.18
cycle (Chris Bainbridge)
- Fix for an ACPI/PNP device enumeration regression introduced during
the 3.16 cycle caused by failing to include two PNP device IDs into
the list of IDs that PNP device objects need to be created for
(Witold Szczeponik)
- Fixes for two minor mistakes in the ACPI GPIO properties
documentation (Antonio Ospite, Rafael J Wysocki)"
* tag 'pm+acpi-4.1-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
* acpi-resources:
x86/PCI/ACPI: Make all resources except [io 0xcf8-0xcff] available on PCI bus
* acpi-battery:
ACPI / SBS: Add 5 us delay to fix SBS hangs on MacBook
* acpi-doc:
ACPI / documentation: Fix ambiguity in the GPIO properties document
ACPI / documentation: fix a sentence about GPIO resources
* acpi-pnp:
ACPI / PNP: add two IDs to list for PNPACPI device enumeration
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=tOGf
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes against v4.1-rc1" from Tony Lindgren:
Fixes for omaps, mostly a fix for power power consumption
creeping up during idle, and two l3-noc device fixes:
- Fix power consumption creeping up with I2C4 staying on
- Fix n900 microphone bias voltages
- Fix dra7 l3-noc for host clock
- Fix omap5 l3-noc id address decoding
The rest are all just minor dts fixes:
- Fix changed EXTCON_USB_GPIO_USB in defconfig
- Fix missing isp and iva #iommu-cells property
- Various beagle x15 dts fixes for pre-production changes
- Fix am437x-sk display dts entries
* tag 'omap-for-v4.1/fixes-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
bus: omap_l3_noc: Fix master id address decoding for OMAP5
bus: omap_l3_noc: Fix offset for DRA7 CLK1_HOST_CLK1_2 instance
ARM: dts: dra7: Fix efuse register size for ABB
ARM: dts: am57xx-beagle-x15: Switch GPIO fan number
ARM: dts: am57xx-beagle-x15: Switch UART mux pins
ARM: dts: am437x-sk: reduce col-scan-delay-us
ARM: dts: am437x-sk: fix for new newhaven display module revision
ARM: dts: am57xx-beagle-x15: Fix RTC aliases
ARM: dts: am57xx-beagle-x15: Fix IRQ type for mcp7941x
ARM: dts: omap3: Add #iommu-cells to isp and iva iommu
ARM: omap2plus_defconfig: Enable EXTCON_USB_GPIO
ARM: dts: OMAP3-N900: Add microphone bias voltages
ARM: OMAP2+: Fix omap off idle power consumption creeping up
- A couple of imx23-olinuxino device tree fixes regarding to LED GPIO
polarity and USB dr_mode setting
- One i.MX28 device tree fix on AUART4 TX-DMA interrupt name
- Add missing pwm-cells to PWM4 for i.MX25 device tree
- Fix imx6q-phytec device tree to get correct USB VBUS control
- Drop invalid pinctrl-assert-gpios property from imx6qdl-sabreauto
device tree, which was sneaked in from vendor device tree
- One fix on Wolfram's broken email address
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVQO+yAAoJEFBXWFqHsHzOWkwH/RQGJQOAXT5QFwCxwjJ8rWbQ
QdB7SWUFufEoAUura83ZrER3FT1WmIRrtvLYypdopUUPhABT8cir5nwRjVd0iMc1
NaC31HohR27N3XZ0zt8yFlvpm03MSYirgpPyB8/tkvMhMv3ghlz5az2PzoAzc5vl
X9uOricn+gKWZsOYQ2X90VJtvNtipV64NKhwEWkg+t1lyxZmfcP30iY8LM3/B21D
qP4k08SIuPo3YoIPjITSmHqtzgp5X9Rf1FTfKmBvecBtt5W4GfrbtsylTvC1ISQC
p4FhDBOrN8hRl1ocbSQvFQybz2poOF/UTFwpWHtAPJxwY11j+IDs2SC33H7whXs=
=H+ZO
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into fixes
Pull "The i.MX fixes for 4.1" from Shawn Guo:
- A couple of imx23-olinuxino device tree fixes regarding to LED GPIO
polarity and USB dr_mode setting
- One i.MX28 device tree fix on AUART4 TX-DMA interrupt name
- Add missing pwm-cells to PWM4 for i.MX25 device tree
- Fix imx6q-phytec device tree to get correct USB VBUS control
- Drop invalid pinctrl-assert-gpios property from imx6qdl-sabreauto
device tree, which was sneaked in from vendor device tree
- One fix on Wolfram's broken email address
* tag 'imx-fixes-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
ARM: dts: imx6qdl-sabreauto: remove pinctrl-assert-gpios
ARM: dts: imx28: Fix AUART4 TX-DMA interrupt name
ARM: dts: imx25: Add #pwm-cells to pwm4
ARM: dts: imx6: phyFLEX: USB VBUS control is active-high
ARM: mach-imx: devices: platform-sdhci-esdhc-imx: fix broken email address
ARM: dts: imx23-olinuxino: Fix dr_mode of usb0
ARM: dts: imx23-olinuxino: Fix polarity of LED GPIO
In our department we are using some older Janz ICAN3-modules in our dekstop
pcs. There we have slightly different carrier boards than the janz-cmodio
supported in the kernel sources, called CAN-PCI2 with two submodules. But the
pci configuration regions are identical. So extending the supported pci devices
to the corresponding device ids is sufficient to get the drivers working.
* The old ICAN3-modules with firmware 1.28 need more then 250ms for the restart
after reset. I've increased the timeout to 500ms.
* The janz_ican3 module uses the raw can services of the Janz-firmware, this
means firmware must be ICANOS/2. Our ICAN3-modules are equipped with
CAL/CANopen-firmware, so I must use the appropriate commands for the layer
management services.
Te driver detects the firmware after module reset and selects the commands
matching the firmware. This affects the bus on/off-command
(ican3_set_bus_state) and the configuration of the bittiming
(ican3_set_bittiming). For better diagnostics the detected firmware string is
presented as sysfs attribute (fwinfo).
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
This patch adds documentation for the existing sysfs entries for the janz PCI
module.
Signed-off-by: Andreas Gröger <andreas24groeger@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The current definition of struct can_frame has a 16-byte size, with 8-byte
alignment, but the 3 bytes of padding are not explicit like the similar 2 bytes
of padding of struct canfd_frame. Make it explicit so it is easier to read.
Signed-off-by: Shawn Landden <shawn@churchofgit.com>
Acked-by: Oliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
the SSIF driver has been in the main kernel for a while.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iEYEABECAAYFAlVJYpsACgkQIXnXXONXERcc1wCfZS0viLVcju2FdzgpXrI+nEcp
gXcAn0dznQiTK0qO44qUCtjwtmKvfJaT
=1yl/
-----END PGP SIGNATURE-----
Merge tag 'for-linus-4.1-1' of git://git.code.sf.net/p/openipmi/linux-ipmi
Pull IPMI fixes from Corey Minyard:
"Lots of minor IPMI fixes, especially ones that have have come up since
the SSIF driver has been in the main kernel for a while"
* tag 'for-linus-4.1-1' of git://git.code.sf.net/p/openipmi/linux-ipmi:
ipmi: Fix multi-part message handling
ipmi: Add alert handling to SSIF
ipmi: Fix a problem that messages are not issued in run_to_completion mode
ipmi: Report an error if ACPI _IFT doesn't exist
ipmi: Remove unused including <linux/version.h>
ipmi: Don't report err in the SI driver for SSIF devices
ipmi: Remove incorrect use of seq_has_overflowed
ipmi:ssif: Ignore spaces when comparing I2C adapter names
ipmi_ssif: Fix the logic on user-supplied addresses
Document the bindings for abracon,abx80x and related compatibles.
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Philippe De Muyter <phdm@macqel.be>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The documentation shows a need for gcc > 4.9.2, but it's really >=. The
Kconfig entries don't show require versions so add them. Correct a
latter/later typo too. Also mention that gcc 5 required to catch out of
bounds accesses to global and stack variables.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Andrey Ryabinin <a.ryabinin@samsung.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
BR_GROUPFWD_RESTRICTED bitmask restricts users from setting values to
/sys/class/net/brX/bridge/group_fwd_mask that allow forwarding of
some IEEE 802.1D Table 7-10 Reserved addresses:
(MAC Control) 802.3 01-80-C2-00-00-01
(Link Aggregation) 802.3 01-80-C2-00-00-02
802.1AB LLDP 01-80-C2-00-00-0E
Change BR_GROUPFWD_RESTRICTED to allow to forward LLDP frames and document
group_fwd_mask.
e.g.
echo 16384 > /sys/class/net/brX/bridge/group_fwd_mask
allows to forward LLDP frames.
This may be needed for bridge setups used for network troubleshooting or
any other scenario where forwarding of LLDP frames is desired (e.g. bridge
connecting a virtual machine to real switch transmitting LLDP frames that
virtual machine needs to receive).
Tested on a simple bridge setup with two interfaces and host transmitting
LLDP frames on one side of this bridge (used lldpd). Setting group_fwd_mask
as described above lets LLDP frames traverse bridge.
Signed-off-by: Bernhard Thaler <bernhard.thaler@wvnet.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the adapters have spaces in their names, but that's really
hard to pass in as a module or kernel parameters. So ignore the
spaces.
Signed-off-by: Corey Minyard <cminyard@mvista.com>
The L3 Error handling on OMAP5 for the most part is very similar
to that of OMAP4, and had leveraged common data structures and
register layout definitions so far. Upon closer inspection, there
are a few minor differences causing an incorrect decoding and
reporting of the master NIU upon an error:
1. The L3_TARG_STDERRLOG_MSTADDR.STDERRLOG_MSTADDR occupies
11 bits on OMAP5 as against 8 bits on OMAP4, with the master
NIU connID encoded in the 6 MSBs of the STDERRLOG_MSTADDR
field.
2. The CLK3 FlagMux component has 1 input source on OMAP4 and 3
input sources on OMAP5. The common DEBUGSS source is at a
different input on each SoC.
Fix the above issues by using a OMAP5-specific compatible property
and using SoC-specific data where there are differences.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The first paragraph in Documentation/acpi/gpio-properties.txt is
ambiguous, so make it more clear.
Reported-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Antonio Ospite <ao2@ao2.it>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch divides the IPv6 flow label space into two ranges:
0-7ffff is reserved for flow label manager, 80000-fffff will be
used for creating auto flow labels (per RFC6438). This only affects how
labels are set on transmit, it does not affect receive. This range split
can be disbaled by systcl.
Background:
IPv6 flow labels have been an unmitigated disappointment thus far
in the lifetime of IPv6. Support in HW devices to use them for ECMP
is lacking, and OSes don't turn them on by default. If we had these
we could get much better hashing in IPv6 networks without resorting
to DPI, possibly eliminating some of the motivations to to define new
encaps in UDP just for getting ECMP.
Unfortunately, the initial specfications of IPv6 did not clarify
how they are to be used. There has always been a vague concept that
these can be used for ECMP, flow hashing, etc. and we do now have a
good standard how to this in RFC6438. The problem is that flow labels
can be either stateful or stateless (as in RFC6438), and we are
presented with the possibility that a stateless label may collide
with a stateful one. Attempts to split the flow label space were
rejected in IETF. When we added support in Linux for RFC6438, we
could not turn on flow labels by default due to this conflict.
This patch splits the flow label space and should give us
a path to enabling auto flow labels by default for all IPv6 packets.
This is an API change so we need to consider compatibility with
existing deployment. The stateful range is chosen to be the lower
values in hopes that most uses would have chosen small numbers.
Once we resolve the stateless/stateful issue, we can proceed to
look at enabling RFC6438 flow labels by default (starting with
scaled testing).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Build fix for SMP=n in book3s_xics.c
- Fix for Daniel's pci_controller_ops on powernv.
- Revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- Two EEH fixes from Gavin.
- Fix for CR corruption from Sam.
- Selftest build fix.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=S0WU
-----END PGP SIGNATURE-----
Merge tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux
Pull powerpc fixes from Michael Ellerman:
- build fix for SMP=n in book3s_xics.c
- fix for Daniel's pci_controller_ops on powernv.
- revert the TM syscall abort patch for now.
- CPU affinity fix from Nathan.
- two EEH fixes from Gavin.
- fix for CR corruption from Sam.
- selftest build fix.
* tag 'powerpc-4.1-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mpe/linux:
powerpc/powernv: Restore non-volatile CRs after nap
powerpc/eeh: Delay probing EEH device during hotplug
powerpc/eeh: Fix race condition in pcibios_set_pcie_reset_state()
powerpc/pseries: Correct cpu affinity for dlpar added cpus
selftests/powerpc: Fix the pmu install rule
Revert "powerpc/tm: Abort syscalls in active transactions"
powerpc/powernv: Fix early pci_controller_ops loading.
powerpc/kvm: Fix SMP=n build error in book3s_xics.c
Not used.
pedit sets TC_MUNGED when packet content was altered, but all the core
does is unset MUNGED again and then set OK2MUNGE.
And the latter isn't tested anywhere. So lets remove both
TC_MUNGED and TC_OK2MUNGE.
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: Alexei Starovoitov <ast@plumgrid.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sentence "These resources are used be used to pass ..." contains
a suspicious repetition, likely the author meant "These resources can
be used to pass ...".
Simplify the wording.
Signed-off-by: Antonio Ospite <ao2@ao2.it>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Change default key details to be more obviously unspecified.
Reported-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: James Morris <james.l.morris@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are a number of small USB fixes for 4.2-rc2. They revert one
problem patch, fix some minor things, and add some new quirks for
"broken" devices.
All have been in linux-next successfully.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iEYEABECAAYFAlVCMNMACgkQMUfUDdst+ylQJwCgsGHQVK4YgrIOCpIkXoc+riy1
VWkAnip86mUGKRej4jrrRvTGvm3maeTj
=/oWf
-----END PGP SIGNATURE-----
Merge tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are a number of small USB fixes for 4.2-rc2. They revert one
problem patch, fix some minor things, and add some new quirks for
"broken" devices.
All have been in linux-next successfully"
* tag 'usb-4.1-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
cdc-acm: prevent infinite loop when parsing CDC headers.
Revert "usb: host: ehci-msm: Use devm_ioremap_resource instead of devm_ioremap"
usb: chipidea: otg: remove mutex unlock and lock while stop and start role
uas: Set max_sectors_240 quirk for ASM1053 devices
uas: Add US_FL_MAX_SECTORS_240 flag
uas: Allow uas_use_uas_driver to return usb-storage flags
This reverts commit feba40362b.
Although the principle of this change is good, the implementation has a
few issues.
Firstly we can sometimes fail to abort a syscall because r12 may have
been clobbered by C code if we went down the virtual CPU accounting
path, or if syscall tracing was enabled.
Secondly we have decided that it is safer to abort the syscall even
earlier in the syscall entry path, so that we avoid the syscall tracing
path when we are transactional.
So that we have time to thoroughly test those changes we have decided to
revert this for this merge window and will merge the fixed version in
the next window.
NB. Rather than reverting the selftest we just drop tm-syscall from
TEST_PROGS so that it's not run by default.
Fixes: feba40362b ("powerpc/tm: Abort syscalls in active transactions")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
The usb-storage driver sets max_sectors = 240 in its scsi-host template,
for uas we do not want to do that for all devices, but testing has shown
that some devices need it.
This commit adds a US_FL_MAX_SECTORS_240 flag for such devices, and
implements support for it in uas.c, while at it it also adds support
for US_FL_MAX_SECTORS_64 to uas.c.
Cc: stable@vger.kernel.org # 3.16
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull networking fixes from David Miller:
1) mlx4 doesn't check fully for supported valid RSS hash function, fix
from Amir Vadai
2) Off by one in ibmveth_change_mtu(), from David Gibson
3) Prevent altera chip from reporting false error interrupts in some
circumstances, from Chee Nouk Phoon
4) Get rid of that stupid endless loop trying to allocate a FIN packet
in TCP, and in the process kill deadlocks. From Eric Dumazet
5) Fix get_rps_cpus() crash due to wrong invalid-cpu value, also from
Eric Dumazet
6) Fix two bugs in async rhashtable resizing, from Thomas Graf
7) Fix topology server listener socket namespace bug in TIPC, from Ying
Xue
8) Add some missing HAS_DMA kconfig dependencies, from Geert
Uytterhoeven
9) bgmac driver intends to force re-polling but does so by returning
the wrong value from it's ->poll() handler. Fix from Rafał Miłecki
10) When the creater of an rhashtable configures a max size for it,
don't bark in the logs and drop insertions when that is exceeded.
Fix from Johannes Berg
11) Recover from out of order packets in ppp mppe properly, from Sylvain
Rochet
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (41 commits)
bnx2x: really disable TPA if 'disable_tpa' option is set
net:treewide: Fix typo in drivers/net
net/mlx4_en: Prevent setting invalid RSS hash function
mdio-mux-gpio: use new gpiod_get_array and gpiod_put_array functions
netfilter; Add some missing default cases to switch statements in nft_reject.
ppp: mppe: discard late packet in stateless mode
ppp: mppe: sanity error path rework
net/bonding: Make DRV macros private
net: rfs: fix crash in get_rps_cpus()
altera tse: add support for fixed-links.
pxa168: fix double deallocation of managed resources
net: fix crash in build_skb()
net: eth: altera: Resolve false errors from MSGDMA to TSE
ehea: Fix memory hook reference counting crashes
net/tg3: Release IRQs on permanent error
net: mdio-gpio: support access that may sleep
inet: fix possible panic in reqsk_queue_unlink()
rhashtable: don't attempt to grow when at max_size
bgmac: fix requests for extra polling calls from NAPI
tcp: avoid looping in tcp_send_fin()
...
Fix a typo in the TX DMA interrupt name for AUART4.
This patch makes AUART4 operational again.
Signed-off-by: Marek Vasut <marex@denx.de>
Fixes: f30fb03d4d ("ARM: dts: add generic DMA device tree binding for mxs-dma")
Cc: stable@vger.kernel.org
Acked-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
dell-laptop: Add support for keyboard backlight.
toshiba_acpi: Adaptive keyboard, hotkey, USB sleep and charge,
and backlight updates. Update sysfs documentation.
toshiba_bluetooth: Fix enabling/disabling loop on recent devices
apple-gmux: lock iGP IO to protect from vgaarb changes
other: Fix typos, clear gcc warnings, clarify pr_* messages,
correct return types, update MAINTAINERS.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJVOzXzAAoJEKbMaAwKp364yjQH/3RJQAiemygVKTv8npk6am4W
6NjoQHwFbvbHnea1DsMBI66DgvDFuXBi04/eKoFtZiSQdt3LOWyF04VY7yPdGKT/
0yIgxMonhLk/lbBiU1PmyAsloOI4mG3zylOO+zJv66LeW0q2vjlLK7xE7AJn0dVU
hRn+Wl0YCjPzEEB4uZpKY6V0+7ys0Odxd2MeYu7pcs5DQzbvzeo4JRwUL4VtNiX9
M1I4ucBRA9jjnuNDzr4d9WtttorOOymoBYy3KFE+2QzDr5chhXTbWp6mRzwnYRvy
siOEPLzeR9jTSB4U514I1CktsCmYxvGnrGcNj1IgiY8VFujoh9j6Ndh339f8064=
=O+n4
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86
Pull x86 platform driver updates from Darren Hart:
"This series includes significant updates to the toshiba_acpi driver
and the reintroduction of the dell-laptop keyboard backlight additions
I had to revert previously. Also included are various fixes for
typos, warnings, correctness, and minor bugs.
Specifics:
dell-laptop:
- add support for keyboard backlight.
toshiba_acpi:
- adaptive keyboard, hotkey, USB sleep and charge, and backlight
updates. Update sysfs documentation.
toshiba_bluetooth:
- fix enabling/disabling loop on recent devices
apple-gmux:
- lock iGP IO to protect from vgaarb changes
other:
- Fix typos, clear gcc warnings, clarify pr_* messages, correct
return types, update MAINTAINERS"
* tag 'platform-drivers-x86-v4.1-1' of git://git.infradead.org/users/dvhart/linux-platform-drivers-x86: (25 commits)
toshiba_acpi: Do not register vendor backlight when acpi_video bl is available
MAINTAINERS: Add me on list of Dell laptop drivers
platform: x86: dell-laptop: Add support for keyboard backlight
Documentation/ABI: Update sysfs-driver-toshiba_acpi entry
toshiba_acpi: Fix pr_* messages from USB Sleep Functions
toshiba_acpi: Update and fix USB Sleep and Charge modes
wmi: Use bool function return values of true/false not 1/0
toshiba_bluetooth: Fix enabling/disabling loop on recent devices
toshiba_bluetooth: Clean up *_add function and disable BT device at removal
toshiba_bluetooth: Add three new functions to the driver
toshiba_acpi: Fix the enabling of the Special Functions
toshiba_acpi: Use the Hotkey Event Type function for keymap choosing
toshiba_acpi: Add Hotkey Event Type function and definitions
x86/wmi: delete unused wmi_data_lock mutex causing gcc warning
apple-gmux: lock iGP IO to protect from vgaarb changes
MAINTAINERS: Add missing Toshiba devices and add myself as maintainer
toshiba_acpi: Update events in toshiba_acpi_notify
intel-oaktrail: Fix trivial typo in comment
thinkpad_acpi: off by one in adaptive_keyboard_hotkey_notify_hotkey()
thinkpad_acpi: signedness bugs getting current_mode
...
Here's a set of updates to the Chrome OS platform drivers for this merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can make your
own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The laptop driver
is trying to be smart and not instantiate the devices that don't answer to
probe. For the trackpad that can come up in two modes (bootloader or regular),
this gets complicated since the driver already knows how to handle the two
modes including the actual addresses used. So now the laptop driver needs to
know more too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few bugfixes
from him, kbuild and myself.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQIcBAABAgAGBQJVOyVhAAoJEIwa5zzehBx3U/gP/jEqIMKEB6r0qApnYLU/0v2V
6AiAtQBDZ6PSNDOqy5Mo5HoMQ0WI09n4xvml3Ntmx0/584RGECn8nlFvwlowIxNo
FLGYcKWuy8w8wKgN19hhEYySnTEex4+kBuDTITvya61SpvxUUfu7fpGV+DXwM2CS
aJQdMOwl24BJ4gjev9JS5QasyZrAzZVuDwo8vSKG6PKZNGgC1uyjOrm+NjiTEW15
FzCk77rRHfiN6Zr9C79ZfqV/nWKm4rPvaJJOiNr2vZUQ/0bhbvSHp3/BekjtnlOv
W6GbUCoDT6/DU/p1SP2Yegqk5pOEcqKQFe7Uc3YDSfiNLNCp03nF1RuIoi/NzfDy
1GcLYWAvHCrtmpQwqM/gIgc9uAsFN9Stin2G79xt3U/dUitdAmwMsCfqDE1FO63e
pGjPx0H7e1Ot3en3O5agaAlYlsokptKl3bIVOMfK6s6bH3RK4Y83LxwsVQKYkayA
TyulczOPnx6i4+acQroIwpFTj8QhhNjjhBU5gXTebVj4B/CwfieZBadaYF23O765
shX71oUJ1gQ6LCZtu8brl/82uk3sSkpVDi8e5WWaSnLfnAmqtU/ITy5yg77uuD0b
RAdHxVFUO6Y0FspWmWzBckrPec7ub+SKglCACq8HNciGx/9BWx6NUWI9FK93CDIu
O36D/l9hoUvA0gds5Iom
=NVa4
-----END PGP SIGNATURE-----
Merge tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform
Pull chrome platform updates from Olof Johansson:
"Here's a set of updates to the Chrome OS platform drivers for this
merge window.
Main new things this cycle is:
- Driver changes to expose the lightbar to users. With this, you can
make your own blinkenlights on Chromebook Pixels.
- Changes in the way that the atmel_mxt trackpads are probed. The
laptop driver is trying to be smart and not instantiate the devices
that don't answer to probe. For the trackpad that can come up in
two modes (bootloader or regular), this gets complicated since the
driver already knows how to handle the two modes including the
actual addresses used. So now the laptop driver needs to know more
too, instantiating the regular address even if the bootloader one
is the probe that passed.
- mfd driver improvements by Javier Martines Canillas, and a few
bugfixes from him, kbuild and myself"
* tag 'chrome-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/chrome-platform:
platform/chrome: chromeos_laptop - instantiate Atmel at primary address
platform/chrome: cros_ec_lpc - Depend on X86 || COMPILE_TEST
platform/chrome: cros_ec_lpc - Include linux/io.h header file
platform/chrome: fix platform_no_drv_owner.cocci warnings
platform/chrome: cros_ec_lightbar - fix duplicate const warning
platform/chrome: cros_ec_dev - fix Unknown escape '%' warning
platform/chrome: Expose Chrome OS Lightbar to users
platform/chrome: Create sysfs attributes for the ChromeOS EC
mfd: cros_ec: Instantiate ChromeOS EC character device
platform/chrome: Add Chrome OS EC userspace device interface
platform/chrome: Add cros_ec_lpc driver for x86 devices
mfd: cros_ec: Add char dev and virtual dev pointers
mfd: cros_ec: Use fixed size arrays to transfer data with the EC
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iEYEABECAAYFAlU70nMACgkQ31LbvUHyf1cYgwCfSmPhyLFmr0pGM/BxsVY7K1v6
PaEAn2+7xfZV38E6hwrGMrT42ZvKyL6r
=LHQU
-----END PGP SIGNATURE-----
Merge tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris
Pull arch/cris updates from Jesper Nilsson:
"Some much needed love for the CRIS-port.
There's a bunch of changes this time, giving the CRISv32 port a bit of
modern makeover with device-tree, irq domain and gpiolib support, and
more switchover to generic frameworks.
Some small fixes and removal of the theoretical SMP support brings up
the rear"
* tag 'cris-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/jesper/cris:
cris: fix integer overflow in ELF_ET_DYN_BASE
CRISv32: use GENERIC_SCHED_CLOCK
CRISv32: use MMIO clocksource
CRISv32: use generic clockevents
CRIS: use generic headers via Kbuild
CRIS: use generic cmpxchg.h
CRIS: use generic atomic.h
CRIS: use generic atomic bitops
CRISv10: remove redundant macros from system.h
CRIS: remove SMP code
CRISv32: don't enable irqs in INIT_THREAD
CRISv32: handle multiple signals
CRISv32: prevent bogus restarts on sigreturn
CRISv32: don't attempt syscall restart on irq exit
Add binding documentation for CRIS
CRIS: add Axis 88 board device tree
CRISv32: add device tree support
CRISv32: add irq domains support
CRIS: enable GPIOLIB
Commit 567e4b7973 ("net: rfs: add hash collision detection") had one
mistake :
RPS_NO_CPU is no longer the marker for invalid cpu in set_rps_cpu()
and get_rps_cpu(), as @next_cpu was the result of an AND with
rps_cpu_mask
This bug showed up on a host with 72 cpus :
next_cpu was 0x7f, and the code was trying to access percpu data of an
non existent cpu.
In a follow up patch, we might get rid of compares against nr_cpu_ids,
if we init the tables with 0. This is silly to test for a very unlikely
condition that exists only shortly after table initialization, as
we got rid of rps_reset_sock_flow() and similar functions that were
writing this RPS_NO_CPU magic value at flow dismantle : When table is
old enough, it never contains this value anymore.
Fixes: 567e4b7973 ("net: rfs: add hash collision detection")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Book3S HV only (debugging aids, minor performance improvements and some
cleanups). But there are also bug fixes and small cleanups for ARM,
x86 and s390.
The task_migration_notifier revert and real fix is still pending review,
but I'll send it as soon as possible after -rc1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.22 (GNU/Linux)
iQEcBAABAgAGBQJVOONLAAoJEL/70l94x66DbsMIAIpZPsaqgXOC1sDEiZuYay+6
rD4n4id7j8hIAzcf3AlZdyf5XgLlr6I1Zyt62s1WcoRq/CCnL7k9EljzSmw31WFX
P2y7/J0iBdkn0et+PpoNThfL2GsgTqNRCLOOQlKgEQwMP9Dlw5fnUbtC1UchOzTg
eAMeBIpYwufkWkXhdMw4PAD4lJ9WxUZ1eXHEBRzJb0o0ZxAATJ1tPZGrFJzoUOSM
WsVNTuBsNd7upT02kQdvA1TUo/OPjseTOEoksHHwfcORt6bc5qvpctL3jYfcr7sk
/L6sIhYGVNkjkuredjlKGLfT2DDJjSEdJb1k2pWrDRsY76dmottQubAE9J9cDTk=
=OAi2
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm
Pull second batch of KVM changes from Paolo Bonzini:
"This mostly includes the PPC changes for 4.1, which this time cover
Book3S HV only (debugging aids, minor performance improvements and
some cleanups). But there are also bug fixes and small cleanups for
ARM, x86 and s390.
The task_migration_notifier revert and real fix is still pending
review, but I'll send it as soon as possible after -rc1"
* tag 'for-linus' of git://git.kernel.org/pub/scm/virt/kvm/kvm: (29 commits)
KVM: arm/arm64: check IRQ number on userland injection
KVM: arm: irqfd: fix value returned by kvm_irq_map_gsi
KVM: VMX: Preserve host CR4.MCE value while in guest mode.
KVM: PPC: Book3S HV: Use msgsnd for signalling threads on POWER8
KVM: PPC: Book3S HV: Translate kvmhv_commence_exit to C
KVM: PPC: Book3S HV: Streamline guest entry and exit
KVM: PPC: Book3S HV: Use bitmap of active threads rather than count
KVM: PPC: Book3S HV: Use decrementer to wake napping threads
KVM: PPC: Book3S HV: Don't wake thread with no vcpu on guest IPI
KVM: PPC: Book3S HV: Get rid of vcore nap_count and n_woken
KVM: PPC: Book3S HV: Move vcore preemption point up into kvmppc_run_vcpu
KVM: PPC: Book3S HV: Minor cleanups
KVM: PPC: Book3S HV: Simplify handling of VCPUs that need a VPA update
KVM: PPC: Book3S HV: Accumulate timing information for real-mode code
KVM: PPC: Book3S HV: Create debugfs file for each guest's HPT
KVM: PPC: Book3S HV: Add ICP real mode counters
KVM: PPC: Book3S HV: Move virtual mode ICP functions to real-mode
KVM: PPC: Book3S HV: Convert ICS mutex lock to spin lock
KVM: PPC: Book3S HV: Add guest->host real mode completion counters
KVM: PPC: Book3S HV: Add helpers for lock/unlock hpte
...
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity in target land the last months.
The highlights include:
- Convert fabric drivers tree-wide to target_register_template() (hch
+ bart)
- iser-target hardening fixes + v1.0 improvements (sagi)
- Convert iscsi_thread_set usage to kthread.h + kill
iscsi_target_tq.c (sagi + nab)
- Add support for T10-PI WRITE_STRIP + READ_INSERT operation (mkp +
sagi + nab)
- DIF fixes for CONFIG_DEBUG_SG=y + UNMAP file emulation (akinobu +
sagi + mkp)
- Extended TCMU ABI v2 for future BIDI + DIF support (andy + ilias)
- Fix COMPARE_AND_WRITE handling for NO_ALLLOC drivers (hch + nab)
Thanks to everyone who contributed this round with new features,
bug-reports, fixes, cleanups and improvements.
Looking forward, it's currently shaping up to be a busy v4.2 as well"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (69 commits)
target: Put TCMU under a new config option
target: Version 2 of TCMU ABI
target: fix tcm_mod_builder.py
target/file: Fix UNMAP with DIF protection support
target/file: Fix SG table for prot_buf initialization
target/file: Fix BUG() when CONFIG_DEBUG_SG=y and DIF protection enabled
target: Make core_tmr_abort_task() skip TMFs
target/sbc: Update sbc_dif_generate pr_debug output
target/sbc: Make internal DIF emulation honor ->prot_checks
target/sbc: Return INVALID_CDB_FIELD if DIF + sess_prot_type disabled
target: Ensure sess_prot_type is saved across session restart
target/rd: Don't pass incomplete scatterlist entries to sbc_dif_verify_*
target: Remove the unused flag SCF_ACK_KREF
target: Fix two sparse warnings
target: Fix COMPARE_AND_WRITE with SG_TO_MEM_NOALLOC handling
target: simplify the target template registration API
target: simplify target_xcopy_init_pt_lun
target: remove the unused SCF_CMD_XCOPY_PASSTHROUGH flag
target/rd: reduce code duplication in rd_execute_rw()
tcm_loop: fixup tpgt string to integer conversion
...
Not much has been happening in PWM land lately, so this contains mostly
minor fixes that didn't seem urgent enough for a late pull-request last
cycle.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=X+q2
-----END PGP SIGNATURE-----
Merge tag 'pwm/for-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm changes from Thierry Reding:
"Not much has been happening in PWM land lately, so this contains
mostly minor fixes that didn't seem urgent enough for a late
pull-request last cycle"
* tag 'pwm/for-4.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm:
pwm: Remove __init initializer for pwm_add_table()
pwm: samsung: Fix output race on disabling
pwm: mxs: Fix period divider computation
pwm: atmel-hlcdc: Add errata handling for sama5d4
pwm: pca9685: Constify struct regmap_config
pwm: imx-pwm: add explicit compatible strings and required clock properties
- correction of copy-paste stupidity while doing the cleanup
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=ULmO
-----END PGP SIGNATURE-----
Merge tag 'dma-buf-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf
Pull dma-buf updates from Sumit Semwal:
"Minor cleanup only; this could've gone in for the 4.0 merge window,
but for a copy-paste stupidity from me.
It has been in the for-next since then, and no issues reported.
- cleanup of dma_buf_export()
- correction of copy-paste stupidity while doing the cleanup"
* tag 'dma-buf-for-4.1' of git://git.kernel.org/pub/scm/linux/kernel/git/sumits/dma-buf:
staging: android: ion: fix wrong init of dma_buf_export_info
dma-buf: cleanup dma_buf_export() to make it easily extensible
Daniel Borkmann