The raid0 MD personality does not start a raid0 array with any of its
data devices missing.
dm-raid was removing data/metadata device pairs unconditionally if it
failed to read a superblock off the respective metadata device of such
pair, resulting in failure to start arrays with the raid0 personality.
Avoid removing any data/metadata device pairs in case of raid0
(e.g. lvm2 segment type 'raid0_meta') thus allowing MD to start the
array.
Also, avoid region size validation for raid0.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
attempt_restore_of_faulty_devices() is limited to 64 when it should support
the new maximum of 253 when identifying any failed devices. It clears any
revivable devices via an MD personality hot remove and add cylce to allow
for their recovery.
Address by using existing functions to retrieve and update all failed
devices' bitfield members in the dm raid superblocks on all RAID devices
and check for any devices to clear in it.
Whilst on it, don't call attempt_restore_of_faulty_devices() for any MD
personality not providing disk hot add/remove methods (i.e. raid0 now),
because such personalities don't support reviving of failed disks.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
'lvchange --refresh RaidLV' causes a mapped device suspend/resume cycle
aiming at device restore and resync after transient device failures. This
failed because flag RT_FLAG_RS_RESUMED was always cleared in the suspend path,
thus the device restore wasn't performed in the resume path.
Solve by removing RT_FLAG_RS_RESUMED from the suspend path and resume
unconditionally. Also, remove superfluous comment from raid_resume().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
On LVM2 conversions via lvconvert(8), the target keeps mapped devices in
frozen state when requesting RAID devices be resynchronized. This
applies to e.g. adding legs to a raid1 device or taking over from raid0
to raid4 when the rebuild flag's set on the new raid1 legs or the added
dedicated parity stripe.
Also, fix frozen recovery for reshaping as well.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
During a resynchronization, device status char 'a' is output on the raid
status line for every device of a RAID set. It changes from 'a' to 'A'
(unless device failure) when the resynchronization completes.
Interrupting and restarting a resynchronization, by reloading the DM
table, erroneously lead to status char 'A'.
Fix this by avoiding setting the MD_RECOVERY_REQUESTED flag in
raid_preresume().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When lvm2 userspace requests a RaidLV repair, it sets the rebuild
constructor flag on the new replacement DataLVs but does not clear the
respective MetaLVs. Hence the superblock that is loaded from such new
MetaLVs may have a non-zero incompat_features member and the constructor
will fail with false-positive on incompat_features.
Solve by initializing the incompat_features member properly.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
__CTR_FLAG_MIN_RECOVERY_RATE was used instead of __CTR_FLAG_MAX_RECOVERY_RATE
thus causing max_recovery_rate to be rejected in case min_recovery_rate
was already set.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
raid_io_hints() was retrieving the number of data stripes used for the
calculation of io_opt from struct r5conf, which is not defined for raid0
mappings.
Base the calculation on the in-core raid_set structure instead.
Also, adjust to use to_bytes() for the sector -> bytes conversion
throughout.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use 'unsigned int' where appropriate.
Return negative errors.
Correct an indentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add "delta_disks" constructor argument support to raid1 to allow for
consistent userspace disk addition/removal handling.
Fix raid_status() to report all raid disks with status and table output
on disk adding reshapes, not just the ones listed on the mddev; optimize
its rebuild and writemostly output.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Enhance rs_reshape_requested() check function to be more transparent and
fix its raid10 check.
Streamline the constructor by factoring out reshaping preparation into
fucntion rs_prepare_reshape().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Resizing a RAID set during recovery can be allowed, because the MD
resynchronization thread will either stop any ongoing recovery in case
of shrinking below the current recovery position or carry on recovery
to the new size if the set is growing.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add function rs_setup_recovery() to allow for defined setup of RAID set
recovery in the constructor.
Will be called with dev_sectors={0, rdev->sectors, MaxSectors} to
recover a new or enforced sync, grown or not to be synhronized RAID set
respectively.
Prevents recovery on raid0, which doesn't support it.
Enforces recovery on raid6 to ensure properly defined Syndromes
mandatory for that MD personality are being created.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
A newly introduced function has 'const int' as the return type,
but as "make W=1" reports, that has no meaning:
drivers/md/dm-raid.c:510:18: error: type qualifiers ignored on function return type [-Werror=ignored-qualifiers]
This changes the return type to plain 'int'.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 33e53f0685 ("dm raid: introduce extended superblock and new raid types to support takeover/reshaping")
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Superblock updates where bogus causing some takovers/reshapes to fail.
Introduce new runtime flag (RT_FLAG_KEEP_RS_FROZEN) to keep a raid set
frozen when a layout change was requested. Userpace will immediately
reload the table w/o the flags requesting such change once they made it
to the superblocks and any change of recovery/reshape offsets has to be
avoided until after read.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add bool functions rs_is_recovering and rs_is_reshaping()
to test for ongoing recovery/reshaping respectively in order
to reject respective requests on ongoing ones.
Remove ctr array size check, because ti->len and array
sectors will differ during disk addition/removal reshape.
Use __is_raid10_near() rather than type string compare.
Introduce rs_check_reshape() and rs_start_reshape(),
use the former in the ctr to reject bogus rehsape requests
and the latter in preresume to actually start a reshape.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add rs_is_reshapable(), rs_data_stripes(), rs_reshape_requested(),
rs_set_dev_and_array_sectors() and rs_adjust_data_offsets()
Remove superfluous check for reshape message
Correct runtime bit definitions to be incremental
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
It is more intuitive to manage each raid level's features in terms of
what is supported rather than what isn't supported.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Renamed functions and variables with leading single underscore to have a
double underscore. Renamed some functions to have better names. Folded
functions that were split out without reason.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Also update module description to "raid0/1/10/4/5/6 target"
Reported by Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
No idea what Heinz was doing with the versioning but upstream commit
4c9971ca6a ("dm raid: make sure no feature flags are set in metadata")
bumped to 1.8.0 already.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
There ti_error_* wrappers added very little. No other DM target has
ever gone to such lengths to wrap setting ti->error.
Also fixes some NULL derefences via rs->ti->error.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The target's status interface has to provide the new 'data_offset' value
to allow userspace to retrieve the kernels offset to the data on each
raid device of a raid set. This is the base for out-of-place reshaping
required to not write over any data during reshaping (e.g. change
raid6_zr -> raid6_nc):
- add rs_set_cur() to be able to start up existing array in case of no
takeover; use in ctr on takeover check
- enhance raid_status()
- add supporting functions to get resync/reshape progress and raid
device status chars
- fixup rebuild table line output race, which does miss to emit
'rebuild N' on fully synced/rebuild devices, because it is relying on
the transient 'In_sync' raid device flag
- add new status line output for 'data_offset', which'll later be used
for out-of-place reshaping
- fixup takeover not working for all levels
- fixup raid0 message interface oops caused by missing checks
for the md threads, which don't exist in case of raid0
- remove ALL_FREEZE_FLAGS not needed for takeover
- adjust comments
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Heinz Mauelshagen