There is at least the worker context, the receiver context, the context of
receiving netlink packts.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We don't discard anything here, really.
We resolve conflicting, concurrent writes to overlapping data blocks.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
To avoid confusion with REQ_DISCARD aka TRIM, rename our
"discard concurrent write acks" from P_DISCARD_WRITE to P_SUPERSEDED.
At the same time, rename the drbd request event DISCARD_WRITE
to CONFLICT_RESOLVED. It already triggers both successful completion
or restart of the request, depending on our RQ_POSTPONED flag.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The DISCARD_CONCURRENT flag should be set on one node and cleared on the
other node.
As the code was before it was theoretical possible that a node accepts the
meta socket, but has to close it later on, and keeps the DISCARD_CONCURRENT
flag.
Correct this by moving the clear_bit(DISCARD_CONCURRENT) where the packet
gets sent.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since the listening socket is open all the time, it was possible to
get into stable "initial packet S crossed" loops.
* when both sides realize in the drbd_socket_okay() call at the end
of the loop that the other side closed the main socket you had
the chance to get into a stable loop with repeated "packet S crossed"
messages.
* when both sides do not realize with the drbd_socket_okay() call at the end
of the loop that the other side closed the main socket you had
the chance to get into a stable loop with alternating "packet S crossed"
"packet M crossed" messages.
In order to break out these stable loops randomize the behaviour if
such a crossing of P_INITIAL_DATA or P_INITIAL_META packets is detected.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since now our listening socket is open all the time we will get
connection tries of the peer always in. No need to try it three
times.
This is valid when connecting to older peers as well, it simply
increases the probability that the new version DRBD will accept
a connection instead that it will establish one.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since the drbd_socket_okay() function itself tests if the the
socket is NULL, the explicit test "if (sock.socket && &msock.socket)"
was redundent.
Apart from that the address opperator ('&') before msock.socket rendered
the test pointless.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
In 8.4, we may have bios spanning two activity log extents.
Fixup drbd_al_begin_io() and drbd_al_complete_io() to deal with zero sized bios.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We now can schedule only a specific range of sectors for online verify,
or interrupt a running verify without interrupting the connection.
Had to bump the protocol version differently, we are now 101.
Added verify_can_do_stop_sector() { protocol >= 97 && protocol != 100; }
Also, the return value convention for worker callbacks has changed,
we returned "true/false" for "keep the connection up" in 8.3,
we return 0 for success and <= for failure in 8.4.
Affected: receive_state()
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
cherry-picked and adapted from drbd 9 devel branch
DRBD requests (struct drbd_request) are already on the per resource
transfer log list, and carry their epoch number. We do not need to
additionally link them on other ring lists in other structs.
The drbd sender thread can recognize itself when to send a P_BARRIER,
by tracking the currently processed epoch, and how many writes
have been processed for that epoch.
If the epoch of the request to be processed does not match the currently
processed epoch, any writes have been processed in it, a P_BARRIER for
this last processed epoch is send out first.
The new epoch then becomes the currently processed epoch.
To not get stuck in drbd_al_begin_io() waiting for P_BARRIER_ACK,
the sender thread also needs to handle the case when the current
epoch was closed already, but no new requests are queued yet,
and send out P_BARRIER as soon as possible.
This is done by comparing the per resource "current transfer log epoch"
(tconn->current_tle_nr) with the per connection "currently processed
epoch number" (tconn->send.current_epoch_nr), while waiting for
new requests to be processed in wait_for_work().
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
cherry-picked and adapted from drbd 9 devel branch
In 8.4, we don't distinguish between "resource work" and "connection
work" yet, we have one worker for both, as we still have only one connection.
We only ever used the "data.work",
no need to keep the "meta.work" around.
Move tconn->data.work to tconn->sender_work.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This could be exploited by a peer which runs modified code.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Changes to the role and disk state should be delayed or rejected
while we establish a connection.
This is necessary, since the peer will base its resync decision
on the UUIDs and the state we sent in the drbd_connect() function.
The most prominent example for this race is becoming primary after
sending state and UUIDs and before the state changes to C_WF_CONNECTION.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since drbd_bump_write_ordering() is called in the attaching
process while the disk state is D_ATTACHING, it was not
considering these three flags during attach.
A call to this function was missing form drbd_adm_disk_opts().
Fixed both issues.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Transfer log epochs, and therefore P_BARRIER packets,
are per resource, not per volume.
We must not associate them with "some random volume".
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
w_restart_write(), run from worker context, calls __drbd_make_request()
and further drbd_al_begin_io(, delegate=true), which then
potentially deadlocks. The previous patch moved a BUG_ON to expose
such call paths, which would now be triggered.
Also, if we call __drbd_make_request() from resource worker context,
like w_restart_write() did, and that should block for whatever reason
(!drbd_state_is_stable(), resource suspended, ...),
we potentially deadlock the whole resource, as the worker
is needed for state changes and other things.
Create a dedicated retry workqueue for this instead.
Also make sure that inc_ap_bio()/dec_ap_bio() are properly paired,
even if do_retry() needs to retry itself,
in case __drbd_make_request() returns != 0.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbd_accept was modelled after kernel_accept
with drbd commit 53eb779 in July 2008.
Only, kernel_accept was then broken, and only fixed later
with kernel commit 1b08534e in Dec 2008:
net: Fix module refcount leak in kernel_accept()
Impact: protocol families provided as modules, e.g. ipv6 or ib_sdp,
would soon have their reference count become negative, preventing
them from being unloaded (likely), or worse, hit zero without actually
being unused, allowing them to be unloaded while still in use (unlikely,
but if triggered, causing a kernel crash).
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
For compatibility reasons 8.4 has to send P_STATE_CHG_REQ (instead
of P_CONN_ST_CHG_REQ) when disconnecting.
In the receiving code path we missed to convert the old
answer (P_STATE_CHG_REPLY) back to 8.4 logic. Therefore
the CL_ST_CHG_SUCCESS or CL_ST_CHG_FAIL bit in the flags word
of mdev got set, while the state code was waiting for
the CONN_WD_ST_CHG_OKAY or CONN_WD_ST_CHG_FAIL bits in tconn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With commit from Mon Mar 28 16:33:12 2011 +0200
"drbd: drbd_connect(): Initialize struct drbd_socket before sending anything"
tconn->data.sock and tconn->meta.sock get assigned early, in
conn_connect.
The early assigning can trigger an OOPS, because it may released the socket
without acquiring the mutex protecting the socket. An other thread (worker)
might use setsockopt() on the socket while it gets free()ed.
Restored the (proven) 8.3 behavior of assigning these sockets after the two
connections are established.
Credits for reporting the issue are going to Arne Redlich.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If the asender thread, or request_timer_fn(), or some other part of
the code, decided to drop the connection (because of timeout or other),
but the receiver just now was processing a P_STATE packet, there was a
chance that receive_state() would do a hard state change
"re-establishing" an already failed connection without additional handshake.
Log excerpt:
Remote failed to finish a request within ko-count * timeout
peer( Secondary -> Unknown ) conn( Connected -> Timeout ) pdsk( UpToDate -> DUnknown )
asender terminated
...
peer( Unknown -> Secondary ) conn( Timeout -> Connected ) pdsk( DUnknown -> UpToDate ) peer_isp( 0 -> 1 )
...
Connection closed
peer( Secondary -> Unknown ) conn( Connected -> Unconnected ) pdsk( UpToDate -> DUnknown ) peer_isp( 1 -> 0 )
receiver terminated
Impact:
while the connection state is erroneously "Connected",
requests may be queued and even sent,
which would never be acknowledged,
and may have been missed by the cleanup.
These requests would never be completed.
The next drbd_suspend_io() will then lock up,
waiting forever for these requests to complete.
Fixed in several code paths:
Make sure the connection state is NetworkFailure or worse
before starting the cleanup in drbd_disconnect().
This should make sure the cleanup won't miss any requests.
Disallow receive_state() to "upgrade" the connection state
from an error state. This will make sure the "illegal" state
transition won't happen.
For all connection failure states,
relax the safe-guard in sanitize_state() again
to silently mask out those state changes
(e.g. Timeout -> Connected becomes Timeout -> Timeout).
Note by Philipp Reisner:
The 3rd chunk described as "relax the safe-guard..."
is not there in 8.4 as it is relaxed to the maximum in
8.4 already
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
New config option for the disk secition "read-balancing", with
the values: prefer-local, prefer-remote, round-robin, when-congested-remote.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Recent commit
drbd: Move write_ordering from mdev to tconn
introduced a new idr_for_each loop over all volumes,
but did not take necessary rcu locks or krefs.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Wait until IO is drained in all volumes.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This is necessary since the transfer_log on the sending is also
per tconn.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
An epoch object needs a pointer to the mdev it was received for.
This is necessary to be able to send the barrier ack packet for
the same volume as the original barrier packet was assigned to.
This prepares the next step, in which the (receiver side)
epoch list is moved from the device (mdev) to the connection (tconn)
object.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This is necessary in order to prepare the move of the (receiver side)
epoch list from the device (mdev) to the connection (tconn) objects.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* drbd-8.3:
drbd: O_SYNC gives EIO on ramdisks for some kernels (eg. RHEL6).
drbd: send intermediate state change results to the peer
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since version 4.6.1 gcc warns about variables that get
a value assigned, but which are never read later on.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With sync-after dependencies, given "lucky" timing of pause/unpause
events, and the end of an empty (0 bits set) resync was sometimes not
detected on the SyncTarget, leading to a "stalled" SyncSource state.
Fixed this by expecting not only "Inconsistent -> UpToDate" but also
"Consistent -> UpToDate" transitions for the peer disk state
to end a resync.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If we get into the C_BROKEN_PIPE cstate once, the state engine set the
thi->t_state of the receiver thread to restarting. But with the while loop
in drbdd_init() a new connection gets established. After the call into
drbdd() returns immediately since the thi->t_state is not RUNNING. The
restart of drbd_init() then resets thi->t_state to RUNNING.
I.e. after entering C_BROKEN_PIPE once, the next successful established
connection gets wasted.
The two parts of the fix:
* Do not cause the thread to restart if we detect the issue
with the sockets while we are in C_WF_CONNECTION.
* Make sure that all actions that would have set us to C_BROKEN_PIPE
happen before the state change to C_WF_REPORT_PARAMS.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The last data-integrity-alg fix made data integrity checking work when the
algorithm was changed for an established connection, but the common case of
configuring the algorithm before connecting was still broken. Fix that.
Signed-off-by: Andreas Gruenbacher <agruen@linbit.com>
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Refer to the settings by the names which drbdsetup and drbd.conf are using.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
When removing a volume/device we need to switch the connection
status of the peer back into WFReportParams.
Before this fix it was left in Connected state. That means that
the peer device continued to inform us about state changes, etc...
But we deleted that minor -> protocol error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* drbd-8.3:
documentation: Documented detach's --force and disk's --disk-timeout
drbd: Implemented the disk-timeout option
drbd: Force flag for the detach operation
drbd: Allow new IOs while the local disk in in FAILED state
drbd: Bitmap IO functions can not return prematurely if the disk breaks
drbd: Added a kref to bm_aio_ctx
drbd: Hold a reference to ldev while doing meta-data IO
drbd: Keep a reference to the bio until the completion handler finished
drbd: Implemented wait_until_done_or_disk_failure()
drbd: Replaced md_io_mutex by an atomic: md_io_in_use
drbd: moved md_io into mdev
drbd: Immediately allow completion of IOs, that wait for IO completions on a failed disk
drbd: Keep a reference to barrier acked requests
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
drbdadm already has a --dry-run option, so this option cannot directly be
passed through to drbdsetup. Rename the drbdsetup option to resolve this
conflict.
For backward compatibility, make --dry-run an alias of --tentative.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This is what it is called in config files and on the command line as
well.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* Updates to all configuration items is done under genl_lock().
Including removal of mdevs or tconns.
* All read non sleeping read sides are protected by rcu
* All sleeping read sides keep reference counts to keep the
objects alive
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Preparing removal of drbd_cfg_rwsem
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Change the --no-tcp-cork drbdsetup command line option as well as
the no_cork netlink packet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Change the --no-disk-drain drbdsetup command line option as well as
the no_disk_drain netlink packet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Change the --no-disk-flushes drbdsetup command line option as well as
the no_disk_flush netlink packet.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This removes the issue with using peer_seq_lock out of different
contexts.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
* Moved rs_planed into it, named total
* When having a pointer to the object the values can
be embedded into the fifo object.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Preparing to use the same mutex for disk_conf updates
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If a forced disconnect hits a restarting receiver right after it passed
its final "if (C_DISCONNECTING)" test in drbdd_init(), but before it was
actually restarted by drbd_thread_setup, we could be left with a
connection stuck in C_DISCONNECTING, never reaching C_STANDALONE,
which would be necessary to take it down or reconfigure it.
Move the last cleanup into w_after_conn_state_ch(), and do an additional
state change request in conn_try_disconnect(), just in case.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The main purpose of this is to allow to turn data integrity checking on
and off on demand without causing interruptions.
Implemented by allocating tconn->peer_integrity_tfm only when receiving
a P_PROTOCOL message. l accesses to tconn->peer_integrity_tf happen in
worker context, and no further synchronization is necessary.
On the sender side, tconn->integrity_tfm is modified under
tconn->data.mutex, and a P_PROTOCOL message is sent whenever. All
accesses to tconn->integrity_tfm already happen under this mutex.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We allocate hash transformations with crypto_alloc_hash() which will
only return hash algorithms. It is not necessary to reconfirm that we
actually got a hash algorithm.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
It is not enough to grab net_conf->integrity_alg under rcu_read_lock()
and access it outside of it; the entire net_conf object may be gone by
then.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
If an admin requests disconnect at a time when the state handling
already disconnects/reconnects, there have been some races.
Make sure to always really stop the network threads before
returning success for disconnect. Do not pretend successfull
forced disconnect, if the state handling returned an error.
Return success from drbd_adm_down() only after all threads are finished.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Now since it is possible to change the two_primaries config
flag while the connection is up, make sure we treat a peer_req
in a consistent way if the config flag changes while the peer_req
is under IO.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Removing the get_net_conf()/put_net_conf() functions
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Removing the get_net_conf()/put_net_conf() calls
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The wire protocol is no longer a property that is negotiated
between the two peers. It is now expressed with two bits
(DP_SEND_WRITE_ACK and DP_SEND_RECEIVE_ACK) in each data
packet. Therefore the primary node is free to change the
wire protocol at any time without disconnect/reconnect.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
With this commit the locking for all accesses to IDRs is complete:
* Non sleeping read accesses are protected by RCU
* sleeping read accesses are protocted by a read lock on drbd_cfg_rwsem
* accesses that add anything are protected by a write lock
* accesses that remove an object are protoected by a write lock
and a call to synchronize_rcu() after it is removed from the IDR
and before the object is actually free()ed.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Since have now header 100, that has space for 16 bit volume numbers,
the high byte of the length in header 95 is no longer reserved for
8 bit volume numbers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The 8 byte header finally becomes too small. With the protocol 100 header we
have 16 bit for the volume number, proper 32 bit for the data length, and
32 bit for further extensions in the future.
Previous versions of drbd are using version 80 headers for all packets
short enough for protocol 80. They support both header versions in
worker context, but only version 80 headers in asynchronous context.
For backwards compatibility, continue to use version 80 headers for
short packets before protocol version 100.
From protocol version 100 on, use the same header version for all
packets.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Prepare the introduction of the protocol 100 headers. The actual protocol
header is removed for the packet declarations. I.e. allow us to use the
packets with different headers.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Centralize sock->mutex locking and unlocking in [drbd|conn]_prepare_command()
and [drbd|conn]_send_comman().
Therefore all *_send_* functions are touched to use these primitives instead
of drbd_get_data_sock()/drbd_put_data_sock() and former helper functions.
That change makes the *_send_* functions more standardized.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
We want to avoid bio_split for bios crossing activity log boundaries.
So we may need to activate two activity log extents "atomically".
drbd_al_begin_io() needs to know more than just the start sector.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Packets of type P_HAND_SHAKE define which protocol versions and features
a node supports. For clarity, call those packets P_CONNECTION_FEATURES
instead.
(This does not determine the features that a specific drbd device
supports, such as drbd protocol A, B, C.)
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The first packets exchanged when a connection is established are
referred to as P_HAND_SHAKE_S and P_HAND_SHAKE_M in the code, followed
by P_HAND_SHAKE packets. To avoid confusion between these two unrelated
things, call the initial packets P_INITIAL_DATA and P_INITIAL_META.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The receive handlers do not all handle unknown volume numbers the same
way.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
These messages can only trigger in case there is a pretty obvious
internal programming error.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
There is no need to send protocol 80 headers to peers that understand
protocol 95 headers. Make sure that we don't send protocol 95 headers
until we have agreed upon a protocol version with our peer, though.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
The pattern of receiving a fixed number of bytes and warning if a short
packet is received and the receiver has not actively been interruped is
repeated many times; clean that up.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This helps to ensure that we don't miss one of them when changing their
return value semantics.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
This commit breaks the API again.
Move per-volume former syncer options into disk_conf.
Move per-connection former syncer options into net_conf.
Renamed the remainign sync_conf to res_opts
Syncer settings have been changeable at runtime, so we need to prepare
for these settings to be runtime-changeable in their new home as well.
Introduce new configuration operations, and share the netlink attribute
between "attach" (create new disk) and "disk-opts" (change options).
Same for "connect" and "net-opts".
Some fields cannot be changed at runtime, however.
Introduce a new flag GENLA_F_INVARIANT to be able to trigger on that in
the generated validation and assignment functions.
Signed-off-by: Philipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: Lars Ellenberg <lars.ellenberg@linbit.com>
Philipp Reisner