This patch adds System MMU nodes to the devices that are specific to
Exynos3250 series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
This patch adds System MMU nodes that are specific to Exynos4210/4x12
series.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The Odroid XU3 Lite is almost the same as XU3, except:
1. Lower CPU frequencies (1.8 GHz for A15 and 1.3 GHz for A7, instead of
2.0 GHz and 1.4 GHz).
2. No DisplayPort.
3. No TI INA231 energy measurement sensors.
This patch moves common nodes (which is almost everything) to a common
DTSI file and adds a new XU3 Lite DTS.
Currently in comparison to XU3, only the INA231 sensors are disabled to
remove the warning:
ina2xx 0-0040: error configuring the device: -6
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add Hardkernel Co., Ltd. to the list of device tree vendor prefixes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The IRQB of S2MPS11 PMIC is wired to XEINT4 (GPX0-4) through pull-up
resistor.
Add interrupt properties and pinctrl configuration to enable RTC wake
alarm of rtc-s5m driver. This also removes a warning:
sec_pmic 4-0066: No interrupt specified, no interrupts
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add nodes for jpeg codec in Exynos5420 SoC.
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@samsung.com>
[k.kozlowski: fixed up minor differences for applying]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add new labels to certain nodes on S3C2416 so they could be easily
referenced by board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes. Additionally remove duplicated serial and uart labels
for serial.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
The i2c_7 node (i2c@12CD0000) with LVDS bridge child node was put in
Exynos5250 Snow DTS file twice. Move the LVDS bridge to proper existing
i2c_7 node.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add new labels to certain nodes so they could be easily referenced by
Exynos5 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
PWM output wasn't working because it wasn't hooked up to its pincontrol.
This patch:
- hooks up PWM to its pincontrol, and documents what
the outputs are on the XU3
- switches the LEDs that are on PWM outputs to use PWM
rather than GPIO.
The main effect is that the brightness of the LEDs can be controlled, and
user-mode fan control is enabled via /sys/class/pwm
Acked-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Peter Chubb <peter.chubb@nicta.com.au>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
For thermal zones:
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Usage of labels instead of full paths reduces possible mistakes when
overriding nodes.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Add new labels to certain nodes so they could be easily referenced by
Exynos4 board DTS files.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since e4b3d38088 ("phy: exynos-video-mipi: Fix regression by adding
support for PMU regmap") the Exynos PMU driver provides regmap to access
the MIPI DPHY registers. The MIPI DPHY driver accesses this regmap
through syscon phandle.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Since e4b3d38088 ("phy: exynos-video-mipi: Fix regression by
adding support for PMU regmap") the Exynos PMU driver provides
regmap to access the MIPI DPHY registers. The MIPI DPHY node uses
a phandle to syscon to get this regmap. The 'reg' field is obsolete.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Replace fixed parent with last parent (obtained with clk_get_parent())
of clocks for devices in mfc and disp power domains. This should improve
behavior if such clocks were reparented by the drivers and new parents
are different than those specified in DTS.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
Pull vfs fix from Al Viro:
"Off-by-one in d_walk()/__dentry_kill() race fix.
It's very hard to hit; possible in the same conditions as the original
bug, except that you need the skipped branch to contain all the
remaining evictables, so that the d_walk()-calling loop in
d_invalidate() decides there's nothing more to do and doesn't go for
another pass - otherwise that next pass will sweep the sucker.
So it's not too urgent, but seeing that the fix is obvious and the
original commit has spread into all -stable branches..."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
d_walk() might skip too much
Pull ARM fixes from Russell King:
"Three fixes this time around:
- fix a memory leak which occurs when probing performance monitoring
unit interrupts
- fix handling of non-PMD aligned end of RAM causing boot failures
- fix missing syscall trace exit path with syscall tracing enabled
causing a kernel oops in the audit code"
* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
ARM: 8357/1: perf: fix memory leak when probing PMU PPIs
ARM: fix missing syscall trace exit
ARM: 8356/1: mm: handle non-pmd-aligned end of RAM
Pull MIPS fixes from Ralf Baechle:
"MIPS fixes for 4.1 all across the tree"
* 'upstream' of git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux:
MIPS: strnlen_user.S: Fix a CPU_DADDI_WORKAROUNDS regression
MIPS: BMIPS: Fix bmips_wr_vec()
MIPS: ath79: fix build problem if CONFIG_BLK_DEV_INITRD is not set
MIPS: Fuloong 2E: Replace CONFIG_USB_ISP1760_HCD by CONFIG_USB_ISP1760
MIPS: irq: Use DECLARE_BITMAP
ttyFDC: Fix to use native endian MMIO reads
MIPS: Fix CDMM to use native endian MMIO reads
Pull turbostat tool fixes from Len Brown:
"Just one minor kernel dependency in this batch -- added a #define to
msr-index.h"
* 'turbostat' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools/power turbostat: update version number to 4.7
tools/power turbostat: allow running without cpu0
tools/power turbostat: correctly decode of ENERGY_PERFORMANCE_BIAS
tools/power turbostat: enable turbostat to support Knights Landing (KNL)
tools/power turbostat: correctly display more than 2 threads/core
Pull SCSI target fixes from Nicholas Bellinger:
"These are mostly minor fixes, with the exception of the following that
address fall-out from recent v4.1-rc1 changes:
- regression fix related to the big fabric API registration changes
and configfs_depend_item() usage, that required cherry-picking one
of HCH's patches from for-next to address the issue for v4.1 code.
- remaining TCM-USER -v2 related changes to enforce full CDB
passthrough from Andy + Ilias.
Also included is a target_core_pscsi driver fix from Andy that
addresses a long standing issue with a Scsi_Host reference being
leaked on PSCSI device shutdown"
* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
iser-target: Fix error path in isert_create_pi_ctx()
target: Use a PASSTHROUGH flag instead of transport_types
target: Move passthrough CDB parsing into a common function
target/user: Only support full command pass-through
target/user: Update example code for new ABI requirements
target/pscsi: Don't leak scsi_host if hba is VIRTUAL_HOST
target: Fix se_tpg_tfo->tf_subsys regression + remove tf_subsystem
target: Drop signal_pending checks after interruptible lock acquire
target: Add missing parentheses
target: Fix bidi command handling
target/user: Disallow full passthrough (pass_level=0)
ISCSI: fix minor memory leak
- Fix sysfs attribute initialization in nct6775 and nct6683 drivers
- Do not attempt to auto-detect tmp435 on I2C address 0x37
- Ensure iio channel is of type IIO_VOLTAGE in ntc_thermistor driver
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cHeh
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-linus-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon fixes from Guenter Roeck:
"Some late hwmon patches, all headed for -stable
- fix sysfs attribute initialization in nct6775 and nct6683 drivers
- do not attempt to auto-detect tmp435 on I2C address 0x37
- ensure iio channel is of type IIO_VOLTAGE in ntc_thermistor driver"
* tag 'hwmon-for-linus-v4.1-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
hwmon: (nct6683) Add missing sysfs attribute initialization
hwmon: (nct6775) Add missing sysfs attribute initialization
hwmon: (tmp401) Do not auto-detect chip on I2C address 0x37
hwmon: (ntc_thermistor) Ensure iio channel is of type IIO_VOLTAGE
We don't assign pi_ctx to desc->pi_ctx until we're certain to succeed
in the function. That means the cleanup path should use the local
pi_ctx variable, not desc->pi_ctx.
This was detected by Coverity (CID 1260062).
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
It seems like we only care if a transport is passthrough or not. Convert
transport_type to a flags field and replace TRANSPORT_PLUGIN_* with a
flag, TRANSPORT_FLAG_PASSTHROUGH.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Aside from whether they handle BIDI ops or not, parsing of the CDB by
kernel and user SCSI passthrough modules should be identical. Move this
into a new passthrough_parse_cdb() and call it from tcm-pscsi and tcm-user.
Reported-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
After much discussion, give up on only passing a subset of SCSI commands
to userspace and pass them all. Based on what pscsi is doing, make sure
to set SCF_SCSI_DATA_CDB for I/O ops, and define attributes identical to
pscsi.
Make hw_block_size configurable via dev param.
Remove mention of command filtering from tcmu-design.txt.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
We now require that the userspace handler set a bit if the command is not
handled.
Update calls to tcmu_hdr_get_op for v2.
Signed-off-by: Andy Grover <agrover@redhat.com>
Reviewed-by: Ilias Tsitsimpis <iliastsi@arrikto.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
See https://bugzilla.redhat.com/show_bug.cgi?id=1025672
We need to put() the reference to the scsi host that we got in
pscsi_configure_device(). In VIRTUAL_HOST mode it is associated with
the dev_virt, not the hba_virt.
Signed-off-by: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org # 2.6.38+
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
There is just one configfs subsystem in the target code, so we might as
well add two helpers to reference / unreference it from the core code
instead of passing pointers to it around.
This fixes a regression introduced for v4.1-rc1 with commit 9ac8928e6,
where configfs_depend_item() callers using se_tpg_tfo->tf_subsys would
fail, because the assignment from the original target_core_subsystem[]
is no longer happening at target_register_template() time.
(Fix target_core_exit_configfs pointer dereference - Sagi)
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reported-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
The following error message is seen when loading the nct6683 driver
with DEBUG_LOCK_ALLOC enabled.
BUG: key ffff88040b2f0030 not in .data!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 186 at kernel/locking/lockdep.c:2988
lockdep_init_map+0x469/0x630()
DEBUG_LOCKS_WARN_ON(1)
Caused by a missing call to sysfs_attr_init() when initializing
sysfs attributes.
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The following error message is seen when loading the nct6775 driver
with DEBUG_LOCK_ALLOC enabled.
BUG: key ffff88040b2f0030 not in .data!
------------[ cut here ]------------
WARNING: CPU: 0 PID: 186 at kernel/locking/lockdep.c:2988
lockdep_init_map+0x469/0x630()
DEBUG_LOCKS_WARN_ON(1)
Caused by a missing call to sysfs_attr_init() when initializing
sysfs attributes.
Reported-by: Alexey Orishko <alexey.orishko@gmail.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Cc: stable@vger.kernel.org # v3.12+
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Marek Szyprowski